TP : Configuration de routeurs CISCO
|
|
- Douglas Day
- 8 years ago
- Views:
Transcription
1 TP : Configuration de routeurs CISCO Sovanna Tan Novembre 2010 révision décembre /19 Sovanna Tan TP : Routeurs CISCO
2 Plan 1 Présentation du routeur Cisco Le système d exploitation /19 Sovanna Tan TP : Routeurs CISCO
3 Le routeur Cisco 1841 Image provenant de : 3/19 Sovanna Tan TP : Routeurs CISCO
4 Fonctionnalités du Routeur Cisco 1841 Fonctions de base du routeur Routage : OSPF, RIP, IGRP Network Address Translation (NAT) Access Control Lists (ACLs) Serveur DHCP Serveur HTTP Administration SNMP 4/19 Sovanna Tan TP : Routeurs CISCO
5 Paramétrage du routeur Interfaces de configuration Command Line Interface : port console, telnet Interface graphique : navigateur web et java pour configuration partielle 5/19 Sovanna Tan TP : Routeurs CISCO
6 Sources Mémento Cisco, Configuration générale, R. Bergoin et C. Bourg, Eyrolles /19 Sovanna Tan TP : Routeurs CISCO
7 1 Présentation du routeur Cisco Le système d exploitation /19 Sovanna Tan TP : Routeurs CISCO
8 Le système d exploitation Modes d accès Exécution (prompt >) : mode par défaut Privilégié (prompt #) : commande pour passer en mode privilégié enable Configuration (prompt (config)#) : commande pour passer en mode configuration configure terminal, pour sortir du mode configuration CTRL Z 8/19 Sovanna Tan TP : Routeurs CISCO
9 Obtenir des informations La commande show show running-config show startup-config show interface nominterface show ip interface brief show ip protocols show ip route show ip access-lists show ip nat translations show ip dhcp binding show version la configuration courante la configuration en mémoire la configuration de l interface vue d ensemble des interfaces les protocoles de routage les tables de routage les ACLs le NAT les réservations DHCP version d 9/19 Sovanna Tan TP : Routeurs CISCO
10 Configuration des interfaces En mode configuration interface nominterface ip address adresseip masquesousreseau description no shutdown sélection adresse IP commentaire activation Exemple : Router(config)# interface Fastethernet 0/0 Router(config-if)# ip address Router(config-if)# description "cote reseau local" Router(config-if)# no shutdown 10/19 Sovanna Tan TP : Routeurs CISCO
11 Configuration de la route par défaut En mode configuration ip route adripreseau masque adripgateway route statique Exemple Router(config)# ip route /19 Sovanna Tan TP : Routeurs CISCO
12 Configuration de OSPF En mode configuration router ospf id network adrreseau masqueinverse area noaire default-information originate redistribute rip [subnets] protocole reseau propagation de la route par défaut redistribution des routes RIP Exemple Router(config)# router ospf 1 Router(config-router)# network area 0 Router(config-router)# network area 0 Router(config-router)# default-information originate 12/19 Sovanna Tan TP : Routeurs CISCO
13 Configuration de RIP En mode configuration router rip version numéro network adrreseau default-information originate protocole version réseau propagation de la route par défaut redistribute ospf id redistribution des routes OSPF Exemple Router(config)# router rip Router(config)# version 2 Router(config-router)# network Router(config-router)# network Router(config-router)# default-information originate 13/19 Sovanna Tan TP : Routeurs CISCO
14 Aperçu de la configuration des ACLs standard En mode configuration access-list numéro deny permit adrsrc [masksrc] règle Exemple : autoriser les paquets dont l adresse source est comprise entre et Router(config)# access-list 7 permit Exemple : appliquer l ACL à l interface Router(config)# interface FastEthernet 0/0 Router(config-if)# ip access-group 7 in 14/19 Sovanna Tan TP : Routeurs CISCO
15 Les objectifs du NAT NAT statique Il rend visible un serveur appartenant à un réseau non routable en faisant correspondre son adresse IP à une adresse IP accessible de l extérieur. En mode configuration ip nat inside source static adrinterne adrexterne règle NAT dynamique Il permet à un ensemble de machines appartenant à un réseau non routable de communiquer avec le réseau externe en transformant leurs adresses en une ou plusieurs adresses accessibles de l extérieur. 15/19 Sovanna Tan TP : Routeurs CISCO
16 Configuration du NAT dynamique En mode configuration ip nat pool nom IPdebut IPFin netmask prefix-length masque ip nat inside source list numéroacl pool nompool [overload] plage lien ACL Exemple : Router(config)# access-list 7 permit Router(config)# ip nat pool ovrld prefix 24 Router(config)# ip nat inside source list 7 pool ovrld overload Router(config)# interface FastEthernet0/0 Router(config-if)# ip address Router(config-if)# ip nat inside Router(config)# interface FastEthernet 0/1 Router(config-if)# ip address Router(config-if)# ip nat outside 16/19 Sovanna Tan TP : Routeurs CISCO
17 Configuration des accès console et telnet En mode configuration username nom priv niveau secret O pass line con 0 line vty 0 4 login local utilisateur accès port console accès telnet demander login/password Exemple Router(config)# user admin priv 15 secret 0 cisco Router(config)# line con 0 Router(config-line)# login local Router(config)# line vty 0 4 Router(config-line)# login local 17/19 Sovanna Tan TP : Routeurs CISCO
18 Configuration du DHCP En mode configuration ip dhcp pool nompool network adrip masque ip dhcp excluded-address adrdebut [adrfin] default-router adrip dns-server adrip service dhcp configuration adresse réseau plage non allouée route par défaut serveur DNS démarrer le service Exemple Router(config)# ip dhcp pool ssi Router(dhcp-config)# network Router(dhcp-config)# default-router Router(dhcp-config)# dns-server Router(dhcp-config)# ip dhcp excluded-address Router(config)# service dhcp 18/19 Sovanna Tan TP : Routeurs CISCO
19 Sauvegarde des configurations En mode privilégié copy running-config startup-config ou write memory copy run tftp://adripserveur:/fichier sauvegarde dans la NVRAM sauvegarde sur un serveur tftp Exemple Router# copy running-config startup-config Router# copy running tftp:// :/config-routeur 19/19 Sovanna Tan TP : Routeurs CISCO
Brest. Backup : copy flash:ppe_brest1 running-config
Brest Backup : copy flash:ppe_brest1 running-config Cisco SF300-08 Mise en place des services : - Serveurs : 10.3.50.0/24 VLAN 2 (port 1) - DSI : 10.3.51.0/24 VLAN 3 (port 2) - Direction : 10.3.52.0/24
More informationLab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt
Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt Objective This lab may introduce new CCNP lab equipment and certain IOS features. This introductory activity also describes how to
More informationIPv6 Workshop: Location Date Security Trainer Name
: Location Date Trainer Name 1/6 Securing the servers 1 ) Boot on linux, check that the IPv6 connectivity is fine. 2 ) From application hands-on, a web server should be running on your host. Add filters
More informationSkills Assessment Student Training Exam
Skills Assessment Student Training Exam Topology Assessment Objectives Part 1: Initialize Devices (8 points, 5 minutes) Part 2: Configure Device Basic Settings (28 points, 30 minutes) Part 3: Configure
More informationICND1-100-101 IOS CLI Study Guide (CCENT)
ICND1-100-101 IOS CLI Study Guide (CCENT) Hostname: 2. hostname SW1 SWITCH CONFIGURATION Mgmt IP: 2. interface vlan 1 3. ip address 10.0.0.2 4. no shut Gateway: 2. ip default-gateway 10.0.0.1 Local User/Pwd:
More informationConfiguring a Router
CHAPTER 3 Configuring a Router This chapter provides information and commands concerning the following topics: Configuring a router, specifically: Names Passwords Interfaces MOTD banners IP host tables
More information- Route Filtering and Route-Maps -
1 Prefix-Lists - Route Filtering and Route-Maps - Prefix-lists are used to match routes as opposed to traffic. Two things are matched: The prefix (the network itself) The prefix-length (the length of the
More information- Basic Router Security -
1 Enable Passwords - Basic Router Security - The enable password protects a router s Privileged mode. This password can be set or changed from Global Configuration mode: Router(config)# enable password
More informationNote: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials.
Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials. CHAPTER 5 OBJECTIVES Configure a router with an initial configuration. Use the
More informationTable of Contents. Cisco Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others
Cisco IOS Firewall to Allow Java Applets From Known Sites w Table of Contents Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others...1 Introduction...1 To Deny Java
More informationLab 1.5.1 Introductory Lab 1 Getting Started and Building Start.txt
Lab 1.5.1 Introductory Lab 1 Getting Started and Building Start.txt Objective This lab will introduce to the student the CCNP lab equipment and certain IOS features that might be new. This introductory
More information3.1 Connecting to a Router and Basic Configuration
3.1 Connecting to a Router and Basic Configuration Objective This lab will focus on the ability to connect a PC to a router in order to establish a console session and observe the user interface. A console
More informationLAB Configuring NAT. Objective. Background/Preparation
LAB Configuring NAT Objective Configure a router to use network address translation (NAT) to convert internal IP addresses, typically private addresses, into outside public addresses. Configure static
More informationCCNA2 Chapter 11 Practice
CCNA2 Chapter 11 Practice Two neighbouring routers are configured for OSPF, but they have different hello and dead intervals. What will happen? They will become adjacent as long as they are configured
More informationBasic Software Configuration Using the Cisco IOS Command-Line Interface
Basic Software Configuration Using the Cisco IOS Command-Line Interface This document describes how to use the Cisco IOS command-line interface (CLI) to perform a basic software configuration for your
More informationCisco Router Configuration Tutorial
Cisco Router Configuration Tutorial Cisco Inter-network Operating System: Cisco IOS Modes of Operation The Cisco IOS software provides access to several different command modes. Each command mode provides
More informationLab 1.2.3 Review of Basic Router Configuration with RIP. Objective. Background / Preparation. General Configuration Tips
Lab 1.2.3 Review of Basic Router Configuration with RIP Objective Cable and configure workstations and routers Setup IP addressing scheme using Class B networks Configure Routing Information Protocol (RIP)
More informationNetwork Security 2. Module 6 Configure Remote Access VPN
1 1 Network Security 2 Module 6 Configure Remote Access VPN 2 Learning Objectives 6.1 Introduction to Cisco Easy VPN 6.2 Configure the Easy VPN Server 6.3 Configure Easy VPN Remote for the Cisco VPN Client
More informationObjectives. Router as a Computer. Router components and their functions. Router components and their functions
2007 Cisco Systems, Inc. All rights reserved. Cisco Public Objectives Introduction to Routing and Packet Forwarding Routing Protocols and Concepts Chapter 1 Identify a router as a computer with an OS and
More informationLab 5.3.8 Configuring PAT with SDM and Static NAT using Cisco IOS Commands
Lab 5.3.8 Configuring PAT with SDM and Static NAT using Cisco IOS Commands Device Host Name Interface IP Address Subnet Mask R1 CustomerRouter Serial 0/0/0 (DTE) 209.165.200.225 255.255.255.224 Fast Ethernet
More informationAngelos Stavrou. OF COURSE there is no Magic so lets see show things work in practice...
Cisco Inter-network Operating System (IOS) A short guide for the NetAdmin Angelos Stavrou Let's start out at the very beginning with the question: "What is a Command?" The most important thing to understand
More informationTopic 7 DHCP and NAT. Networking BAsics.
Topic 7 DHCP and NAT Networking BAsics. 1 Dynamic Host Configuration Protocol (DHCP) IP address assignment Default Gateway assignment Network services discovery I just booted. What network is this? What
More informationDHCP Server Port-Based Address Allocation
The feature provides port-based address allocation support on the Cisco IOS Dynamic Host Configuration Protocol (DHCP) server for the Ethernet platform. The DHCP server provides address assignment support
More informationApplicazioni Telematiche
Angelo Coiro Laboratorio Applicazioni Telematiche L emulatore Packet Tracer Packet Tracer Cisco Packet Tracer is an academic software that allows to emulate Cisco devices Packet Tracer can be used for
More informationHow to Configure Cisco 2600 Routers
Helsinki University of Technology Department of Communications and Networking How to Configure Cisco 2600 Routers Juha Järvinen 10.6.2004 Juha.Jarvinen@netlab.hut.fi Modified by Zhong Yunqiu 7.8.2008 Table
More informationConfiguring WAN Failover with a Cisco 881 Router and an AirLink ES440
Configuring WAN Failover with a Cisco 881 Router and an AirLink ES440 When the AirLink ES440 is combined with a third-party router, the combined solution supports business continuity by providing primary
More informationLab: Basic Router Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Def. Gateway R1 Fa0/0 192.168.1.1 255.255.255.0 N/A S0/0/0 192.168.2.1 255.255.255.0 N/A R2 Fa0/0 192.168.3.1 255.255.255.0 N/A
More informationLab 5.3.7 Configuring DHCP with SDM and the Cisco IOS CLI
Lab 5.3.7 Configuring DHCP with SDM and the Cisco IOS CLI Device Host Name Interface IP Address Subnet Mask R1 Customer Serial 0/0/1 (DTE) 209.165.200.225 255.255.255.224 Fast Ethernet 0/0 192.168.1.1
More informationConfiguring Role-Based Access Control
5 CHAPTER This chapter describes how to configure role-based access control (RBAC) on the Cisco Application Control Engine (ACE) module. This chapter contains the following sections: Information About
More informationICND1 Lab Guide. 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0. Labs powered by
ICND1 Lab Guide 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0 ii Interconnecting Cisco Networking Devices Part 1 100-101 Lab Guide LM20130929/BV2.01 iii 25 Century Blvd. Ste. 500
More informationHow To Configure A Cisco Router With A Cio Router
CHAPTER 1 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
More informationLab Exercise Configure the PIX Firewall and a Cisco Router
Lab Exercise Configure the PIX Firewall and a Cisco Router Scenario Having worked at Isis Network Consulting for two years now as an entry-level analyst, it has been your hope to move up the corporate
More information642 523 Securing Networks with PIX and ASA
642 523 Securing Networks with PIX and ASA Course Number: 642 523 Length: 1 Day(s) Course Overview This course is part of the training for the Cisco Certified Security Professional and the Cisco Firewall
More informationNote concernant votre accord de souscription au service «Trusted Certificate Service» (TCS)
Note concernant votre accord de souscription au service «Trusted Certificate Service» (TCS) Veuillez vérifier les éléments suivants avant de nous soumettre votre accord : 1. Vous avez bien lu et paraphé
More informationLab 2 - Basic Router Configuration
CS326 Fall 2001 Room: PAI 5.48 Name: Lab 2 - Basic Router Configuration In this lab you will learn: the various configuration modes of Cisco 2621 routers how to set up IP addresses for such routers how
More informationNetflow Gamme de Produits Netflow, ntop, nprobe, Nbar NetFlow Analyzer Solarwinds Cisco NetFlow Orion Netflow Traffic Analyzer Intégration avec Orion NPM 2 K à 12 K Live Demo: http://npmv7.solarwinds.net/login.asp
More informationLAB MANUAL for Computer Network
LAB MANUAL for Computer Network CSE-310 F Computer Network Lab L T P - - 3 Class Work : 25 Marks Exam : 25 MARKS Total : 50 Marks This course provides students with hands on training regarding the design,
More informationComware versus Cisco IOS Command Guide
Technical Marketing Engineering Routing and Switching Technology Routing and Switching Comware versus Cisco IOS Command Guide Technical Marketing Brief Revision v5 March 23, 2009 http://www.3com.com 3Com
More informationConfiguring a Gateway of Last Resort Using IP Commands
Configuring a Gateway of Last Resort Using IP Commands Document ID: 16448 Contents Introduction Prerequisites Requirements Components Used Conventions ip default gateway ip default network Flag a Default
More informationCentral America Workshop - Guatemala City Guatemala 30 January - 1 February 07. IPv6 Security
City Guatemala 30 January - 1 February 07 Pedro Lorga (lorga@fccn.pt) Simon Muyal (muyal@renater.pt) Piers O'Hanlon (p.ohanlon@cs.ucl.ac.uk) Laboratory Exercise: Objectives In this laboratory exercise
More informationEnabling Remote Access to the ACE
CHAPTER 2 This chapter describes how to configure remote access to the Cisco Application Control Engine (ACE) module by establishing a remote connection by using the Secure Shell (SSH) or Telnet protocols.
More informationTable des matières 1 Cœur... 1 1 1 Routeur... 1 1 1 1 Configuration... 1 1 1 2 Fichiers de configuration... 1
Table des matières 1 Cœur... 1 1 1 Routeur... 1 1 1 1 Configuration... 1 1 1 2 Fichiers de configuration... 1 1 Routeur 1 1 Routeur 1 1 1 Configuration Nom : routeur1.mlif.local Adresse IP eth0 : dynamique
More informationCisco Configuration Professional Quick Start Guide
Cisco Configuration Professional Quick Start Guide April 29, 2011 This document explains how to start using Cisco Configuration Professional Express (Cisco CP Express) and Cisco Configuration Professional
More informationThe Cisco IOS Firewall feature set is supported on the following platforms: Cisco 2600 series Cisco 3600 series
Cisco IOS Firewall Feature Set Feature Summary The Cisco IOS Firewall feature set is available in Cisco IOS Release 12.0. This document includes information that is new in Cisco IOS Release 12.0(1)T, including
More informationIntroduction ToIP/Asterisk Quelques applications Trixbox/FOP Autres distributions Conclusion. Asterisk et la ToIP. Projet tuteuré
Asterisk et la ToIP Projet tuteuré Luis Alonso Domínguez López, Romain Gegout, Quentin Hourlier, Benoit Henryon IUT Charlemagne, Licence ASRALL 2008-2009 31 mars 2009 Asterisk et la ToIP 31 mars 2009 1
More information«Object-Oriented Multi-Methods in Cecil» Craig Chambers (Cours IFT6310, H08)
«Object-Oriented Multi-Methods in Cecil» Craig Chambers (Cours IFT6310, H08) Mathieu Lemoine 2008/02/25 Craig Chambers : Professeur à l Université de Washington au département de Computer Science and Engineering,
More informationConfiguring Network Address Translation
CHAPTER5 Configuring Network Address Translation The information in this chapter applies to both the ACE module and the ACE appliance unless otherwise noted. This chapter contains the following major sections
More informationConfiguring Static and Dynamic NAT Translation
This chapter contains the following sections: Network Address Translation Overview, page 1 Information About Static NAT, page 2 Dynamic NAT Overview, page 3 Timeout Mechanisms, page 4 NAT Inside and Outside
More informationWorkshop. Avril 2015 Benoit Buonassera benoitb@checkpoint.com 06 72 94 19 98
Workshop Avril 2015 Benoit Buonassera benoitb@checkpoint.com 06 72 94 19 98 BE YOUR CUSTOMER S BEST ADVISOR By using the Security Checkup tool you will increase your business opportunities while bringing
More information- The PIX OS Command-Line Interface -
1 PIX OS Versions - The PIX OS Command-Line Interface - The operating system for Cisco PIX/ASA firewalls is known as the PIX OS. Because the PIX product line was acquired and not originally developed by
More informationConfiguring DHCP. DHCP Server Overview
Configuring DHCP This chapter describes how to configure Dynamic Host Configuration Protocol (DHCP). For a complete description of the DHCP commands listed in this chapter, refer to the DHCP s chapter
More informationEvaluation guide. Vyatta Quick Evaluation Guide
VYATTA, INC. Evaluation guide Vyatta Quick Evaluation Guide A simple step-by-step guide to configuring network services with Vyatta Open Source Networking http://www.vyatta.com Overview...1 Booting Up
More informationLab 4.2.4 Advanced Telnet Operations
Lab 4.2.4 Advanced Telnet Operations Objective Use the telnet command to remotely access other routers. Verify that the application layer between the source and the destination is working properly. Suspend
More informationBrocade to Cisco Comparisons
1 2 3 Console cables - The console cables are not interchangeable between Brocade and Cisco. Each vendor provides their console cable with each manageable unit it sells. Passwords - Neither Cisco or Brocade
More informationLab 7.2.9 Load Balancing Across Multiple Paths Instructor Version 2500
Lab 7.2.9 Load Balancing Across Multiple Paths Instructor Version 2500 Objective onfigure Load balance across multiple paths. Observe the load balancing process. Background/Preparation able a network similar
More informationCork Institute of Technology Master of Science in Computing in Education National Framework of Qualifications Level 9
Cork Institute of Technology Master of Science in Computing in Education National Framework of Qualifications Level 9 February 2005 System and Network Management (Time: 2 Hours) Answer any THREE questions
More informationAudit de sécurité avec Backtrack 5
Audit de sécurité avec Backtrack 5 DUMITRESCU Andrei EL RAOUSTI Habib Université de Versailles Saint-Quentin-En-Yvelines 24-05-2012 UVSQ - Audit de sécurité avec Backtrack 5 DUMITRESCU Andrei EL RAOUSTI
More informationFSM73xx GSM73xx GMS72xxR Shared access to the Internet across Multiple routing VLANs using a Prosafe Firewall
FSM73xx GSM73xx GMS72xxR Shared access to the Internet across Multiple routing VLANs using a Prosafe Firewall This document describes how to: - Create multiple routing VLANs - Obtain Internet access on
More informationComputer Networks Administration Help Manual Sana Saadaoui Jemai Oliver Wellnitz
Technische Universität Braunschweig Institut für Betriebssysteme und Rechnerverbund Computer Networks Administration Help Manual Sana Saadaoui Jemai Oliver Wellnitz Braunschweig, 27 th March 2007 Contents
More informationRemote Method Invocation
1 / 22 Remote Method Invocation Jean-Michel Richer jean-michel.richer@univ-angers.fr http://www.info.univ-angers.fr/pub/richer M2 Informatique 2010-2011 2 / 22 Plan Plan 1 Introduction 2 RMI en détails
More informationConfiguring Server Load Balancing
CHAPTER 6 This chapter describes how to configure server load balancing (SLB) on the Cisco Application Control Engine (ACE) module. This chapter contains the following sections: Information About Server
More informationNAT (Network Address Translation) & PAT (Port Address Translation)
NAT (Network Address Translation) & PAT (Port Address Translation) First let s define NAT terms: Inside local address The IP address assigned to a host on the inside network. The address is usually not
More informationConfiguring Devices for Use with Cisco Configuration Professional (CCP) 2.5
Configuring Devices for Use with Cisco Configuration Professional (CCP) 2.5 Objectives Part 1: Configure CCP Access for Routers Enable HTTP/HTTPS server. Create a user account with privilege level 15.
More informationExperts in Networking. CCNA Cheat Sheet. This CCNA command cheat sheet covers both ICND parts 1 & 2 and covers the current CCNA exam (640-802).
CCNA Cheat Sheet This CCNA command cheat sheet covers both ICND parts 1 & 2 and covers the current CCNA exam (640-802). Whilst not an exhaustive IOS command list it covers the majority of commands found
More informationNetwork Address Translation Commands
Network Address Translation Commands This chapter describes the function and displays the syntax for Network Address Translation (NAT) commands. For more information about defaults and usage guidelines,
More informationChapter 11 Network Address Translation
Chapter 11 Network Address Translation You can configure an HP routing switch to perform standard Network Address Translation (NAT). NAT enables private IP networks that use nonregistered IP addresses
More informationCISCO CATALYST 3550 Series Switches
CISCO CATALYST 3550 Series Switches The switches that belong to this series are stackable and are multilayer switches that provide QoS, high availability and security that are responsible for enhancing
More informationWelcome to Todd Lammle s CCNA Bootcamp
Welcome to Todd Lammle s CCNA Bootcamp Todd Lammle Cisco Authorized CCNA Bootcamps are now available, delivered by CCSI instructor, and popular Sybex author Todd Lammle. Todd Lammle CCNA Training Boot
More informationModifier le texte d'un élément d'un feuillet, en le spécifiant par son numéro d'index:
Bezier Curve Une courbe de "Bézier" (fondé sur "drawing object"). select polygon 1 of page 1 of layout "Feuillet 1" of document 1 set class of selection to Bezier curve select Bezier curve 1 of page 1
More informationNetwork Simulator Lab Study Plan
The CCNA 640-802 Network Simulator has 300 lab exercises, organized both by type (Skill Builder, Configuration Scenario, Troubleshooting Scenario, and Subnetting Exercise) and by major topic within each
More information1 Basic Configuration of Cisco 2600 Router. Basic Configuration Cisco 2600 Router
1 Basic Configuration of Cisco 2600 Router Basic Configuration Cisco 2600 Router I decided to incorporate the Cisco 2600 into my previously designed network. This would give me two seperate broadcast domains
More informationNetwork Scenarios Pagina 1 di 35
Network Scenarios Pagina 1 di 35 Table of Contents Network Scenarios Cisco 827 s Network Connections Internet Access Scenarios Before You Configure Your Internet Access Network Replacing a Bridge or Modem
More informationAPNIC Members Training Course Security workshop. 2-4 July, 2008. Port Vila Vanuatu. In conjunction with PACNOG 4
APNIC Members Training Course Security workshop 2-4 July, 2008 Port Vila Vanuatu In conjunction with PACNOG 4 Router device security lab 1. APNIC s remote lab In these exercises you will be remotely accessing
More informationChapter 3 Using Access Control Lists (ACLs)
Chapter 3 Using Access Control Lists (ACLs) Access control lists (ACLs) enable you to permit or deny packets based on source and destination IP address, IP protocol information, or TCP or UDP protocol
More informationCisco Router Configuration Basics. Scalable Infrastructure Workshop
Cisco Router Configuration Basics Scalable Infrastructure Workshop Router Components p RAM n Holds operating system, data structures, packet buffers, ARP cache, and routing tables n Reset on reload n Router
More informationBasic Configuration of the Cisco 12000 Series Internet Router
CHAPTER 2 Basic Configuration of the Cisco 12000 Series Internet Router This chapter describes how to boot and configure the Cisco 12000 Series Internet Router. It discusses the following subjects: Cisco
More informationListe d'adresses URL
Liste de sites Internet concernés dans l' étude Le 25/02/2014 Information à propos de contrefacon.fr Le site Internet https://www.contrefacon.fr/ permet de vérifier dans une base de donnée de plus d' 1
More informationLAN-Cell to Cisco Tunneling
LAN-Cell to Cisco Tunneling Page 1 of 13 LAN-Cell to Cisco Tunneling This Tech Note guides you through setting up a VPN connection between a LAN-Cell and a Cisco router. As the figure below shows, the
More informationWiNG 5.X How To. Policy Based Routing Cache Redirection. Part No. TME-05-2012-01 Rev. A
WiNG 5.X How To Policy Based Routing Cache Redirection Part No. TME-05-2012-01 Rev. A MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark
More informationLab 6.1.3 Configure Local AAA on Cisco Router
Lab 6.1.3 Configure Local AAA on Cisco Router Objective Scenario Topology In this lab, the students will complete the following tasks: Securing and testing access to the privileged EXEC, VTY, and console
More informationLab 8.3.1.2 Configure Basic AP Security through IOS CLI
Lab 8.3.1.2 Configure Basic AP Security through IOS CLI Estimated Time: 30 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, the student will learn the following
More informationControlling Access to a Virtual Terminal Line
Controlling Access to a Virtual Terminal Line First Published: August 18, 2006 Last Updated: August 18, 2006 You can control who can access the virtual terminal lines (vtys) to a router by applying an
More information- Advanced IOS Functions -
1 The Configuration Register - Advanced IOS Functions - The configuration register (config-register) is a hexadecimal value that controls various aspects of how a router boots, including: Baud Rate Boot
More informationConfiguring Dial Backup and Remote Management
13 CHAPTER Configuring Dial Backup and Remote Management The Cisco 800 series access routers support dial-in (for remote management) and dial-out (for dial backup) capabilities. By allowing you to configure
More informationCisco Simulations. Kaplan IT Learning CCNA. Simulator: Cisco Labs. IT Certification Test Preparation. www.kaplanit.com
Cisco Simulations Kaplan IT Learning CCNA Simulator: Cisco Labs IT Certification Test Preparation www.kaplanit.com Contts How to Use This Tool... 4 Initial purchase and setup... 4 Performing the CCNA simulation
More informationLab 4.1.4 Creating a Network Map using CDP Instructor Version 2500
Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500 Objective Use Cisco Discovery Protocol (CDP) commands to get information about neighboring network devices. Background/Preparation CDP
More informationIOS NAT Load Balancing for Two ISP Connections
IOS NAT Load Balancing for Two ISP Connections Document ID: 100658 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot
More informationIntroduction to Cisco router configuration
Introduction to Cisco router configuration AFNOG 2001 Workshop 07 to 11 May 2001 Accra - GHANA By: Adiel AKPLOGAN CAFE Informatique S. A. - TOGO E-mail: adiel@akplogan.net - Web: http://www.akplogan.net
More informationConfiguring a Cisco 2509-RJ Terminal Router
created by: Rainer Bemsel Version 1.0 Dated: Dec/08/2012 For my Cisco LAB, I ve purchased a used Cisco 2509-RJ with RJ45-RJ45 roll-over cables. This TechTip shows my configuration setup, so you can easily
More informationLab 3.8.3 Configure Cisco IOS Firewall CBAC on a Cisco Router
Lab 3.8.3 Configure Cisco IOS Firewall CBAC on a Cisco Router Objective Scenario Topology Estimated Time: 35 minutes Number of Team Members: Two teams with four students per team In this lab exercise,
More informationLab 8.3.3b Configuring a Remote Router Using SSH
Lab 8.3.3b Configuring a Remote Router Using SSH Objectives Use SDM to configure a router to accept SSH connections. Configure SSH client software on a PC. Establish a connection to a Cisco ISR using SSH
More informationConfiguring the Switch with the CLI Setup Program
APPENDIXC Configuring the Switch with the CLI Setup Program This appendix provides a command-line interface (CLI) setup procedure for a standalone switch. To set up the switch by using Express Setup, see
More informationBasic Router Configuration Using Cisco Configuration Professional
Basic Router Configuration Using Cisco Configuration Professional Document ID: 111999 Contents Introduction Prerequisites Components Used Install Cisco Configuration Professional Router Configuration to
More informationLab 8.5.3 Configuring the PIX Firewall as a DHCP Server
Lab 8.5.3 Configuring the PIX Firewall as a DHCP Server Objective Scenario Estimated Time: 15 minutes Number of Team Members: Two teams with four students per team. In this lab, students will learn the
More informationVirtual Fragmentation Reassembly
Virtual Fragmentation Reassembly Currently, the Cisco IOS Firewall specifically context-based access control (CBAC) and the intrusion detection system (IDS) cannot identify the contents of the IP fragments
More informationPersonnalisez votre intérieur avec les revêtements imprimés ALYOS design
Plafond tendu à froid ALYOS technology ALYOS technology vous propose un ensemble de solutions techniques pour vos intérieurs. Spécialiste dans le domaine du plafond tendu, nous avons conçu et développé
More informationAdding an Extended Access List
CHAPTER 11 This chapter describes how to configure extended access lists (also known as access control lists), and it includes the following topics: Information About Extended Access Lists, page 11-1 Licensing
More informationModule 6 Configure Remote Access VPN
Network Security 2 Module 6 Configure Remote Access VPN Learning Objectives 6.1 Introduction to Cisco Easy VPN 6.2 Configure the Easy VPN Server 6.3 Configure Easy VPN Remote for the Cisco VPN Client 4.x
More informationTable of Contents. Cisco How Does Load Balancing Work?
Table of Contents How Does Load Balancing Work?...1 Document ID: 5212...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...1 Load Balancing...1 Per Destination and
More information