TW-EAV510 AC v2. 3G/4G/LTE ADSL2+/Fibre Broadband Router Wireless b/g/n ac 2,4 GHz / 5 GHz VPN. User Manual. Copyright TeleWell Oy

Transcription

1 TW-EAV510 AC v2 3G/4G/LTE ADSL2+/Fbre Broadband Router Wreless b/g/n ac 2,4 GHz / 5 GHz VPN User Manual Copyrght TeleWell Oy

2 Table of Contents Chapter 1: Introducton... 3 Introducton to your Router... 3 Features... 5 Physcal Interface... 7 Package Contents... 7 Devce Descrpton... 8 Chapter 2: Basc Installaton Network Confguraton Factory Default Settngs Chapter 3: Confguraton Status Summary WAN Statstcs Bandwdth Usage G/LTE Status Route ARP DHCP VPN Log Confguraton LAN - Local Area Network IPv6 Autoconfg Interface Groupng Wreless 2.4GHz and 5GHz WAN- Wde Area Network System USB IP Tunnel Securty QoS - Qualty of Servce NAT VPN IPSec VPN Account Advanced Setup Routng DNS Certfcate Multcast Management Dagnostcs Restart Chapter 4: Troubleshootng

3 Chapter 1: Introducton Introducton to your Router The TeleWell TW-EAV510 AC v2 s a fbre-ready ADSL2+/VDSL modem, an all-n-one advanced devce ntegratng Wreless-AC 1300Mbps, 1000 Mb Ethernet, 3G/4G/LTE, and NAS (Network Attached Storage) n one unt. As well as beng IPv6-capable, the TeleWell TW-EAV510 AC v2 ADSL2+ router supports super fast fbre connectons va dual-wan connectvty through a Ggabt Ethernet WAN port. Also, t also has a USB port, allowng the devce to act as a prnt server as well as a NAS (Network Attached Storage) devce wth DLNA (Dgtal Lvng Network Allance). Moreover, the USB port can host a 3G/4G/LTE modem connectng to the 3G/4G/LTE network for Internet access. Wth an array of advanced features, the TeleWell TW-EAV510 AC v2 delvers a future-proof soluton for ADSL2+ connectons, super fast FTTC and ultra-speed FTTH (Fbre-To-The-Home) network deployment and servces. Maxmum wreless performance Wth an ntegrated n Wreless Access Pont, the router delvers up to 6 tmes the speed of an b/g/n ac network devce. It supports a data rate of up to 300Mbps and s also compatble wth b/g/n ac equpment. The Wreless Protected Access (WPA-PSK/WPA2-PSK) and Wreless Encrypton Protocol (WEP) features enhance the level of transmsson securty and access control over wreless LAN. The router also supports the W-F Protected Setup (WPS) standard, allowng users to establsh a secure wreless network by smply pushng a button. If your network requres wder coverage, the bult-n Wreless Dstrbuton System (WDS) repeater functon allows you to expand your wreless network wthout the need for any external wres or cables. 3G/4G/LTE Moblty and Always-on Connectvty Wth 3G/4G/LTE-based Internet connecton (requres an addtonal 3G/4G/LTE USB modem plugged nto the bult-n USB port), user can access nternet through 3G/4G/LTE, whether you are seated at your desk or takng a cross-country trp. The auto fal-over feature ensures optmum connectvty and mnmum nterrupton by quckly and smoothly connectng to a 3G/4G/ LTE network n the event that you ADSL/Fbre/Cable lne fals. The TeleWell TW-EAV510 AC v2 wll then automatcally reconnect to the ADSL/Fbre/Cable connecton when t s restored, reducng connecton costs. These features are perfect for offce stuatons when a constant and smooth WAN connecton s crtcal. IPv6 supported Internet Protocol verson 6 (IPv6) s a verson of the Internet Protocol that s desgned to succeed IPv4. IPv6 has a vastly larger address space than IPv4. Ths results from the use of a 128-bt address, whereas IPv4 uses only 32 bts. The new address space thus supports 2128 (about ) addresses. Ths expanson provdes flexblty n allocatng addresses and routng traffc and elmnates the prmary need for network address translaton (NAT), whch ganed wdespread deployment as an effort to allevate IPv4 address exhauston. The TeleWell TW-EAV510 AC v2 fully supports IPv6 (Internet Protocol Verson 6), launched as the current IPv4 range s fllng up, and IPv6 s gradually becomng the ndspensable addressng system for savvy cloud computng users. Dual stack means the router s capable of runnng IPv4 and IPv6 n parallel durng the transton perod. Wth TeleWell IPv6 enabled devces, three major transton mechansms such as Dual-Stack, Dual-Stack Lte, and 6RD (IPv6 rapd deployment) are supported to be adapted easly nto servce provder s IPv4/IPv6 network 3

4 Jumbo frames supported Jumbo frames are Ethernet frames wth more than 1500 bytes (standard Ethernet frame) of payload. Conventonally, jumbo frames can carry up to 9720 bytes of payload to enjoy a hgh-effcency communcaton n Ggabt Ethernet. Jumbo frames ncrease the frame sze so that a certan large amount of date can be transported wth less effort, reducng CPU utlzaton and ncreasng throughput by reducng the number of frames needng to be processed and reducng the total overhead byte count of all frames sent. Vrtual AP A Vrtual Access Pont s a logcal entty that exsts wthn a physcal Access Pont (AP). When a sngle physcal AP supports multple Vrtual APs, each Vrtual AP appears to statons (STAs) to be an ndependent physcal AP, even though only a sngle physcal AP s present. For example, multple Vrtual APs mght exst wthn a sngle physcal AP, each advertsng a dstnct SSID and capablty set. Alternatvely, multple Vrtual APs mght advertse the same SSID but a dfferent capablty set allowng access to be provded va Web Portal, WEP, and WPA smultaneously. Where APs are shared by multple provders, Vrtual APs provde each provder wth separate authentcaton and accountng data for ther users, as well as dagnostc nformaton, wthout sharng senstve management traffc or data between provders. You can enable the vrtual AP. Web Based GUI It supports web based GUI for confguraton and management. It s user-frendly and comes wth onlne help. It also supports remote management capablty for remote users to confgure and manage ths product. Frmware Upgradeable Devce can be upgraded to the latest frmware through the WEB based GUI. 4

5 Features - Trple-WAN ports for 3G/4G/LTE, ADSL2+, VDSL2, 10/100Mb/1000Mb Ethernet WAN (EWAN) for broadband connectvty /100/10 Mb WAN and LAN - Fbre (FTTC/FTTP/FTTH) ready wth hgh WAN throughput - IPv6 ready (IPv4/IPv6 dual stack) - Auto fal-over - Hgh-speed Internet Access va ADSL2 / 2+; Backward Compatble wth ADSL - Jumbo frames - IEEE b/g/n ac complant Wreless Access Pont wth W-F Protected Setup (WPS) - W-F Protected Access (WPA-PSK/ WPA2-PSK) and Wred Equvalent Prvacy (WEP) support - Secured IPSec VPN wth powerful DES/ 3DES/ AES - PPTP VPN wth Pap/ Chap/ MS-CHAPv2 authentcaton - Pure L2TP and L2TP over IPSec - GRE tunnel - SOHO Frewall Securty wth DoS Preventng and Packet Flterng - Qualty of Servce Control for traffc prortzaton and Bandwdth management - Unversal Plug and Play (UPnP) Complance - Supports IPTV Applcaton - USB port for prnt server, NAS (Samba), DLNA meda server, and 3G/4G LTE USB ADSL Complance - Complant wth ADSL+ / VDSL 2 Standard - Full-rate ANSI T1.413 Issue 2 - G.dmt (ITU G.992.1) - G.hs (ITU G.994.1) - Complant wth ADSL2 Standard - G.dmt.bs (ITU G.992.3) - ADSL2 Annex M (ITU G Annex M) - G.dmt.bs plus (ITU G.992.5) - ADSL2+ Annex M (ITU G Annex M) VDSL 2 Network Protocols and Features - IPv4 or IPv4 / IPv6 Dual Stack - NAT, statc (v4/v6) routng and RIP-1 / 2 - IPv6 Stateless / Stateful Address Auto-confguraton - IPv6 Router Advertsement - IPv6 over PPP - DHCPv6 - IP Tunnel IPv6 n IPv4 (6RD) - IP Tunnel IPv4 n IPv6 (DS-Lte) - Unversal Plug and Play (UPnP) Complant - Dynamc Doman Name System (DDNS) - Vrtual Server, DMZ and one-to-one NAT - SNTP, DNS relay, IGMP snoopng and IGMP proxy for vdeo servce - MLD snoopng and MLD proxy for vdeo servce - Management based-on IP protocol, port number and address 5

6 Frewall - Bult-n NAT Frewall - Stateful Packet Inspecton (SPI) - DoS attack preventon - Packet Flterng (v4/v6) - port, source IP address, destnaton IP address, MAC address - URL Content Flterng (v4/v6) strng or doman name detecton n URL strng - MAC Flterng Qualty of Servce Control - Supports the DffServ approach - Traffc prortzaton and bandwdth management based-on IPv4/IPv6 protocol, port number and address ATM, PTM and PPP Protocols - ATM Adaptaton Layer Type 5 (AAL5) - Multple Protocol over ALL5 (RFC 268, formerly RFC 1483) - Brdged or routed Ethernet encapsulaton - VC and LLC based multplexng - PPP over Ethernet (PPPoE) - PPP over ATM (RFC 2364) Classcal IP over ATM (RFC 1577) - MAC Encapsulated Routng (RFC 1483 MER) - OAM F4 / F5 IPTV Applcatons - IGMP Snoopng and IGMP Proxy - MLD Snoopng and MLD Proxy - Vrtual LAN (VLAN) - Qualty of Servce (QoS) Wreless LAN - Complant wth IEEE b/g/n ac standards GHz and 5GHz rado bands for wreless - Up to 1300 Mbps wreless operaton rate - 64/128 bts WEP supported for encrypton - WPS (W-F Protected Setup) for easy setup - Supports WPS v2 - Wreless Securty wth WPA-PSK / WPA2-PSK support - WDS repeater functon support USB Applcaton Server - 3G/4G/LTE dongle support - DLNA meda server - Prnter Server Vrtual Prvate Network (VPN) - IKE key management - DES, 3DES and AES encrypton for IPSec - L2TP over IPSec - Pap/ Chap/ MS-CHAPv2 authentcaton for PPTP - IPSec pass-through - GRE tunnel 6

7 Management - Web-based GUI for remote and local management (IPv4/IPv6) - Frmware upgrades and confguraton data upload and download va web-based GUI - Embedded Telnet server for remote and local management - Supports DHCP server / clent / relay - Supports SNMP v1,v2, MIB-I and MIB-II - TR-069 supports remote management - Avalable Syslog - Mal alert for WAN IP changed - Auto falover and fallback - Push Servce Physcal Interface - WLAN: 5 x 3db nternal antenna - DSL: ADSL / VDSL port - USB 2.0 port for DLAN, prnter server and 3G/4G/LTE dongle - Ethernet: 4-port 10/100/1000 Mbps auto-crossover (MDI / MDI-X) Swtch - Factory default reset button - WPS push button - Power jack - Power swtch Package Contents - TW-EAV510 AC v2 router - Quck Start Gude - CD contanng Englsh manual - RJ-45 Cat. 5e STP Ethernet cable - RJ-11 ADSL/ telephone cable - Power adapter - Spltter / Mcro-flter (Optonal) Important note for usng ths router Do not use the router n hgh humdty or hgh temperatures Do not use the same power source for the router as other equpment. Do not open or repar the case yourself. If the router s too hot, turn off the power mmedately and have t repared at a qualfed servce center. Avod usng ths product and all accessores outdoors Warnng Do not use the router n hgh humdty or hgh temperatures. Do not use the same power source for the router as other equpment. Do not open or repar the case yourself. If the router s too hot, turn off the power mmedately and have t repared at a qualfed servce center. Avod usng ths product and all accessores outdoors. Place the router on a stable surface. Only use the power adapter that comes wth the package. Usng a dfferent voltage ratng power adapter may damage the router. 7

8 Devce Descrpton The Front LEDs LED Status Meanng 1 Power Red Green Boot falure or n emergency mode System ready 2 Ethernet Port 1-4 (EWAN) Green Blnkng Transmsson speed httng Data beng transmtted/receved 3 Wlan 2.4G / Wlan 5G Green Green blnkng Wreless connecton establshed Sendng/recevng data 4 WPS 2.4G / WPS 5G Green blnkng Off WPS confguraton beng n progress WPS process completed or WPS s off Green Blnkng DSL synchronzng or watng for DSL synchronzng 5 DSL 6 Internet 7 USB 2 / USB 1 Green Off Red Green Off Green Flashng green Successfully connected to an ADSL/VDSL DSLAM Sync DSL cable unplugged Obtanng IP falure Havng obtaned an IP address successfully Router n brdge mode or DSL connecton not present. USB actvate on modem Data s transmsson Off Modem off or no devce attached 8

9 The Rear Ports Port Meanng 1 Power Swtch Power ON / OFF swtch. 2 Power Connect the suppled power adapter to ths jack. 3 RESET After the devce s powered on, press t 5 seconds or above: to restore to factory default settngs (ths s used when you cannot logn to the router, e.g. forgot the password) 4 USB 1 / USB 2 Connect the USB devce (Prnter, 3G/4G LTE USB modem) to ths port. 5 WAN Connect Ethernet cable for WAN connectons 6 Ethernet (LAN1-4) Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when connectng to a PC or an offce/home network of 10Mbps /100Mbps. 7 DSL Connect ths port to the DSL network wth the RJ-11 cable (telephone) provded. Cablng One of the most common causes of problems s bad cablng or ADSL lne(s). Make sure that all connected devces are turned on. On the front panel of your router s a bank of LEDs. Verfy that the LAN Lnk and ADSL lne LEDs are all lt. If they are not, verfy f you are usng the proper cables. If the error perssts, you may have a hardware problem. In ths case, you should contact techncal support. Make sure you have a lne flter wth all devces (e.g. telephones, fax machnes, analogue modems) connected to the same telephone lne and the wall socket (unless you are usng a Central Spltter or Central Flter nstalled by a qualfed and lcensed electrcan), and ensure that all lne flters are correctly nstalled and the rght way around. Mssng lne flters or lne flters nstalled the wrong way 9

10 around can cause problems wth your ADSL connecton, ncludng causng frequent dsconnectons. If you have a back-to-base alarm system you should contact your securty provder for a techncan to make any necessary changes. Chapter 2: Basc Installaton The router can be confgured through your web browser. A web browser s ncluded as a standard applcaton n the followng operatng systems: Lnux, Mac OS, Wndows 8 / 7 / 98 / NT / 2000 / XP / Me / Vsta, etc. The product provdes an easy and user-frendly nterface for confguraton. Please check your PC network components. The TCP/IP protocol stack and Ethernet network adapter must be nstalled. If not, please refer to your Wndows-related or other operatng system manuals. There are ways to connect the router, ether through an external repeater hub or connect drectly to your PCs. However, make sure that your PCs have an Ethernet nterface nstalled properly pror to connectng the router devce. You ought to confgure your PCs to obtan an IP address through a DHCP server or a fxed IP address that must be n the same subnet as the router. The default IP address of the router s and the subnet mask s (.e. any attached PC must be n the same subnet, and have an IP address n the range of to ). The best and easest way s to confgure the PC to get an IP address automatcally from the router usng DHCP. If you encounter any problem accessng the router web nterface t s advsable to unnstall your frewall program on your PCs, as they can cause problems accessng the IP address of the router. Users should make ther own decsons on what s best to protect ther network. Please follow the followng steps to confgure your PC network envronment. Any TCP/IP capable workstaton can be used to communcate wth or through ths router. To confgure other types of workstatons, please consult your manufacturer documentaton Network Confguraton Confgurng a PC n Wndows 7 Go to Start. Clck on Control Panel. Then clck on Network and Internet. 10

11 When the Network and Sharng Center wndow pops up, select and clck on Change adapter settngs on the left wndow panel. Select the Local Area Connecton, and rght clck the con to select Propertes. IPv4: Select Internet Protocol Verson 4 (TCP/IPv4) then clck Propertes 11

12 In the TCP/IPv4 propertes wndow, select the Obtan an IP address automatcally and Obtan DNS Server address automatcally rado buttons. Then clck OK to ext the settng. Clck OK agan n the Local Area Connecton Propertes wndow to apply the new confguraton. IPv6: Select Internet Protocol Verson 6 (TCP/IPv6) then clck Propertes 12

13 In the TCP/IPv6 propertes wndow, select the Obtan an IPv6 address automatcally and Obtan DNS Server address automatcally rado buttons. Then clck OK to ext the settng. Clck OK agan n the Local Area Connecton Propertes wndow to apply the new confguraton. Confgurng a PC n Wndows Vsta Go to Start. Clck on Network. Then clck on Network and Sharng Center at the top bar. 13

14 When the Network and Sharng Center wndow pops up, select and clck on Manage network connectons on the left wndow panel. Select the Local Area Connecton, and rght clck the con to select Propertes. IPv4: Select Internet Protocol Verson 4 (TCP/IPv4) then clck Propertes. 14

15 In the TCP/IPv4 propertes wndow, select the Obtan an IP address automatcally and Obtan DNS Server address automatcally rado buttons. Then clck OK to ext the settng. Clck OK agan n the Local Area Connecton Propertes wndow to apply the new confguraton. IPv6: Select Internet Protocol Verson 6 (TCP/IPv6) then clck Propertes. 15

16 In the TCP/IPv6 propertes wndow, select the Obtan an IPv6 address automatcally and Obtan DNS Server address automatcally rado buttons. Then clck OK to ext the settng. Clck OK agan n the Local Area Connecton Propertes wndow to apply the new confguraton. Factory Default Settngs Before confgurng your router, you need to settngs. Web Interface (Username and Password) Three user levels are provded by ths router, namely Admnstrator, Remote and Local respectvely. See Access Control. Admnstrator Username: admn Password: admn Attenton If you have forgotten the username and/or password of the router, you can restore the devce to ts default settng by pressng the Reset Button more than 5 seconds. Devce LAN IPv4 settngs - IPv4 Address: Subnet Mask: Devce LAN IPv6 settngs - IPv6 Address / prefx: Default s a lnk-local address and s dfferent from each other as MAC address s dfferent from one to one 16

17 DHCP server for IPv4 - DHCP server s enabled - Start IP Address: IP pool counts: 100 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set n the factory. The default values are shown n the table. IPv4 LAN Port IPv4 address Subnet Mask DHCP server functon Enabled ports 1-3 IP addresses for 100 IP addresses contnung from dstrbuton to PCs through WAN Port The RFC1483 Brdged IP LLC functon s enabled to automatcally get the WAN IP address from the ISP IPv6 LAN Port IPv6 address/prefx Default s a lnk-local address and s dfferent from each other as MAC address s dfferent from one to one. WAN Port The RFC1483 Brdged IP LLC functon s enabled to automatcally get the WAN IP address from the ISP DHCP server functon Enabled 17

18 Informaton from your ISP Before confgurng ths devce, you have to check wth your ISP (Internet Servce Provder) to fnd out what knd of servce s provded. Gather the nformaton as llustrated n the followng table and keep t for reference. PPPoE(RFC2516) VPI/VCI, VC / LLC-based multplexng, Username, Password, Servce Name, and Doman Name System (DNS) IP address (t can be automatcally assgned by your ISP when you connect or be set manually). PPPoA(RFC2364) DHCP Clent VPI/VCI, VC / LLC-based multplexng, Username, Password and Doman Name System (DNS) IP address (t can be automatcally assgned by your ISP when you connect or be set manually). VPI/VCI, VC / LLC-based multplexng, Doman Name System (DNS) IP address (t can be automatcally assgned by your ISP when you connect or be set manually). IPoA(RFC1577) VPI/VCI, VC / LLC-based multplexng, IP address, Subnet mask, Gateway address, and Doman Name System (DNS) IP address (t s a fxed IP address). Pure Brdge VPI/VCI, VC / LLC-based multplexng to use Brdged Mode. 18

19 Chapter 3: Confguraton Confguraton va Web Interface Open your web browser; enter the IP address of your router, whch by default s , and clck ok or press Enter key on the keyboard, a logn prompt wndow wll appear. The default root username and password are admn and admn respectvely. Congratulatons! You are now successfully logged n to the Frewall Router! Once you have logged on to your TeleWell TW-EAV510 AC v2 Router va your web browser, you can begn to set t up accordng to your requrements. On the confguraton homepage, the left navgaton pane lnks you drectly to the setup pages, whch nclude: Status (Summary, WAN, Statstcs, Bandwdth Usage, 3G/LTE Status, Route, ARP, DHCP, VPN and Log) Quck Start (Quck Start) Confguraton (LAN, Wreless 2,4 GHz and 5 GHz, WAN, System, USB, IP Tunnel, Securty, Qualty of Servce, NAT, Wake On LAN) VPN (IPSec, VPN Account, PPTP, L2TP, GRE) Advanced Setup (Routng, DNS, Statc ARP, UPnP, Certfcate, Multcast, Management, Dagnostcs) 19

20 Status Ths Secton gves users an easy access to the nformaton about the workng router and access to vew the current status of the router. Here Summary, WAN, Statstcs, Bandwdth Usage, 3G/LTE Status, Route, ARP, DHCP, VPN and Log subsectons are ncluded. Summary The basc nformaton about the devce s provded here (the followng s a confgured screenshots to let users understand clearly). 20

21 Devce Informaton Model Name: Dsplays the model name. Host Name: Dsplays the name of the router. System Up-Tme: Dsplays the elapsed tme snce the devce s on. Date/Tme: Dsplays the current exact date and tme. Sync button s to synchronze the Date/Tme wth your PC tme wthout regard to connectng to nternet or not. Software Verson: Frmware verson. LAN IPv4 Address: Dsplays the LAN IPv4 address. LAN IPv6 Address: Dsplays the LAN IPv6 address. Default s a Lnk-Local address, but when connects to ISP, t wll dsplay the Global Address, lke above fgure. MAC Address: Dsplays the MAC address. DSL PHY and Drver Verson: Dsplay DSL PHY and Drver verson. Wreless Drver Verson: Dsplays wreless drver verson. WAN Lne Rate Upstream (Kbps): Dsplays Upstream lne Rate n Kbps. Lne Rate Downstream (Kbps): Dsplays Downstream lne Rate n Kbps. Default Gateway/IP4 Address: Dsplay Default Gateway and the IPv4 address. Connecton Tme: Dsplays the elapsed tme snce ADSL connecton s up. Prmary DNS Server: Dsplays IPV4 address of Prmary DNS Server. Secondary DNS Server: Dsplays IPV4 address of Secondary DNS Server. Default IPv6 Gateway/IPv6 Address: Dsplay the IPv6 Gateway and the obtaned IPv6 address. WAN Ths table dsplays the nformaton of the WAN connectons, users can turn here for WAN connecton nformaton. Interface: The WAN connecton nterface. Descrpton: The descrpton of ths connecton. Type: The protocol used by ths connecton. Status: To dsconnect or connect the lnk. Connecton Tme: The WAN connecton tme snce WAN s up. IPv4 Address: The WAN IPv4 Address the devce obtaned. IPv6 Address: The WAN IPv6 Address the devce obtaned. 21

22 Statstcs LAN The table shows the statstcs of LAN. Note: P4 can be confgured as EWAN, and when the devce s n EWAN profle, there s no P4/EWAN nterface as P4 s workng as a WAN port. (DSL) (EWAN) Interface: Lst each LAN nterface. P1-P4 ndcates the four LAN nterfaces. Bytes: Dsplay the Receved and Transmtted traffc statstcs n Bytes. Packets: Dsplay the Receved and Transmtted traffc statstcs n Packets. Errors: Dsplay the statstcs of errors arsng n Recevng or Transmttng data. Drops: Dsplay the statstcs of drops arsng n Recevng or Transmttng data. Reset: Press ths button to refresh the statstcs. WAN Servce The table shows the statstcs of WAN. 22

23 Interface: Dsplay the connecton nterface. Descrpton: the descrpton for the connecton. Bytes: Dsplay the WAN Receved and Transmtted traffc statstcs n Bytes. Packets: Dsplay the WAN Receved and Transmtted traffc statstcs n Packests. Errors: Dsplay the statstcs of errors arsng n Recevng or Transmttng data. Drops: Dsplay the statstcs of drops arsng n Recevng or Transmttng data. Reset: Press ths button to refresh the statstcs. xtm The Statstcs-xTM screen dsplays all the xtm statstcs Port Number: Shows number of the port for xtm. In Octets: Number of receved octets over the nterface. Out Octets: Number of transmtted octets over the nterface. In Packets: Number of receved packets over the nterface. Out Packets: Number of transmtted packets over the nterface. In OAM Cells: Number of OAM cells receved. Out OAM Cells: Number of OAM cells transmtted. In ASM Cells: Number of ASM cells receved. Out ASM Cells: Number of ASM cells transmtted. In Packet Errors: Number of receved packets wth errors. In Cell Errors: Number of receved cells wth errors. Reset: Clck to reset the statstcs. 23

24 xdsl Mode: Modulaton protocol, ncludng G.dmt, G.lte, T1.413, ADSL2, AnnexL, ADSL2+ and AnnexM. Traffc Type: Transfer mode, here supports ATM and PTM. Status: Show the status of DSL lnk. Lnk Power State: Show lnk output power state. Lne Codng (Trells): Trells on/off. 24

25 SNR Margn (db): Show the Sgnal to Nose Rato (SNR) margn. Attenuaton (db): Ths s estmate of average loop attenuaton of sgnal. Output Power (dbm): Show the output power. Attanable Rate (Kbps): The sync rate you would obtan. Rate (Kbps): Show the downstream and upstream rate n Kbps. MSGc (#of bytes n overhead channel message): The number of bytes n overhead channel message. B (# of bytes n Mux Data Frame): The number of bytes n Mux Data frame. M (# of Mux Data Frames n FEC Data Frame): The number of Mux Data frames n FEC frame. T (Mux Data Frames over sync bytes): The number of Mux Data frames over all the sync bytes. R (# of check bytes n FEC Data Frame): The number of check bytes n FEC frame. S (rato of FEC over PMD Data Frame length): The rato of FEC over PMD Data frame length L (# of bts n PMD Data Frame): The number of bt n PMD Data frame D (nterleaver depth): Show the nterleaver depth. Delay (msec): Show the delay tme n msec. INP (DMT symbol): Show the DMT symbol. Super Frames: The total number of super frames. Super Frame Errors: The total number of super frame errors. RS Words: Total number of Reed-Solomon code errors. RS Correctable Errors: Total number of RS wth correctable errors. RS Uncorrectable Errors: Total number of RS words wth uncorrectable errors. HEC Errors: Total number of Header Error Checksum errors. OCD Errors: Total number of out-of-cell Delneaton errors. LCD Errors: Total number of Loss of Cell Delneaton. Total Cells: Total number of cells. Data Cells: Total number of data cells Bt Errors: Total number of bt errors. Total ES: Total Number of Errored Seconds. Total SES: Total Number of Severely Errored Seconds. Total UAS: Total Number of Unavalable Seconds. xdsl BER Test: Clck ths button to start a bt Error Rate Test. The ADSL Bt Error Rate (BER) test determnes the qualty of the ADSL connecton. The test s done by transferrng dle cells contanng a known pattern and comparng the receved data wth ths known pattern to check for any errors. Select the Tested Tme (sec), press Start to start test. 25

26 When t s OK, the followng test result wndow wll appear. You can vew the qualty of ADSL connecton. Here the connecton s OK. Reset: Clck ths button to reset the statstcs. Bandwdth Usage Bandwdth Usage provdes users drect vew of bandwdth usage wth smple dagram. Bandwdth usage shows the use of the bandwdth from two angles: Transmtted and Receved, gvng users a clear dea of the usage. LAN Note: P4 can be confgured as EWAN, and when the devce s n EWAN profle, there s no P4/EWAN nterface as P4 s workng as a WAN port. (DSL) 26

27 Press Vew LAN Transmtted button to change the dagram to the statstcs from a Receved Bytes of vew. (Note: means Ethernet port #3, and the traffc nformaton of the port #3 s dentfed wth green, the same color wth P3 n the dagram; other ports all take the same mechansm.) When you press Vew WAN Traffc concurrently button, the WAN Bandwdth Usage pops up so that users can vew the WAN traffc concurrently. WAN Servce Press Vew WAN Transmtted button to change the dagram to the statstcs from a Receved Bytes of vew. Press Vew LAN Traffc concurrently button to drectly swtch to the LAN Bandwdth Usage page to vew the LAN traffc concurrently. 27

28 3G/LTE Status Status: The current status of the 3G/LTE card. Sgnal Strength: The sgnal strength bar ndcates current 3G sgnal strength. Network Name: The network name that the devce s connected to. Network Mode: The current operaton mode for 3G/LTE card, t depends on servce provder and card s lmtaton, GSM or UMTS. Card Name: The name of the 3G/LTE card. Card Frmware: The current frmware for the 3G/LTE card. 28

29 Route Destnaton: The IP address of destnaton network. Gateway: The IP address of the gateway ths route uses. Subnet Mask: The destnaton subnet mask. Flag: Show the status of the route. U: Show the route s actvated or enabled. H (host): destnaton s host not the subnet. G: Show that the outsde gateway s needed to forward packets n ths route. R: Show that the route s renstated from dynamc routng. D: Show that the route s dynamcally nstalled by daemon or redrectng. M: Show the route s modfed from routng daemon or redrect. Metrc: Dsplay the number of hops counted as the Metrc of the route. Servce: Dsplay the servce that ths route uses. Interface: Dsplay the exstng nterface ths route uses. ARP Ths secton dsplays the router s ARP (Address Resoluton Protocol) Table, whch shows the mappng of Internet (IP) addresses to Ethernet (MAC) addresses. Ths s useful as a quck way of determnng the MAC address of the network nterface of your PCs to use wth the router s Securty MAC Flterng functon. Here IPv6 Neghbor Table, lsted wth IPv6 address-mac mappng, s supported. ARP table IP Address: Shows the IP Address of the devce that the MAC address maps to. Flag: Shows the current status of the ARP entres. Complete: the route resolvng s processng well. M (Marked as permanent entry): the route s permanent. P (publsh entry): publsh ths route tem. MAC Address: Shows the MAC address that s corresponded to the IP address of the devce t s mapped to. Devce: here refers to the physcal nterface, t s a concept to dentfy Clents from LAN or WAN. For example, the Clents n LAN, here dsplays br0. Mark: Show clearly the SSID (WLAN) the devce s n. 29

30 DHCP The DHCP Table lsts the DHCP lease nformaton for all IP addresses assgned by the DHCP server n the devce. Host Name: The Host Name of DHCP clent. MAC Address: The MAC Address of nternal DHCP clent host. IP Address: The IP address whch s assgned to the host wth ths MAC address. Expres n: Show the remanng tme after regstraton. Mark: Show clearly the SSID (WLAN) the devce s n. Note: The devces are free to access each other through devce name on condton that they all obtan ther IPs from the DHCP. If the devce IP s obtaned from the DHCP, other devces can access the devce through the devce name. VPN VPN status vewng secton provdes users IPSec, PPTP, L2TP and GRE VPN status. IPSec Name: The IPSec connecton name. Actve: Dsplay the connecton status. Local Subnet: Dsplay the local network. Remote Subnet: Dsplay the remote network. Remote Gateway: The remote gateway address. SA: The Securty Assocaton for ths IPSec entry. Refresh: Clck ths button to refresh the tunnel status. 30

31 PPTP PPTP Server Name: The PPTP connecton name. Enable: Dsplay the connecton status wth cons. Status: The connecton status. Connecton Type: Remote Access or LAN to LAN. Peer Network IP: Dsplay the remote network and subnet mask n LAN to LAN PPTP connecton. Connected By: Dsplay the IP of remote connected clent. Acton: Act to the connecton. Clck Drop button to dsconnect the tunnel connecton. PPTP Clent Name: The PPTP connecton name. Enable: Dsplay the connecton status wth cons. Status: The connecton status. Connecton Type: Remote Access or LAN to LAN. Peer Network IP: Dsplay the remote network and subnet mask n LAN to LAN PPTP connecton. Clent: Assgned IP by PPTP server. Acton: Act to the connecton. Clck Drop button to dsconnect the tunnel connecton. Refresh: Clck ths button to refresh the connecton status. L2TP L2TP Server Name: The L2TP connecton name. Enable: Dsplay the connecton status wth cons. Status: The connecton status. Connecton Type: Remote Access or LAN to LAN. Peer Network IP: Dsplay the remote network and subnet mask n LAN to LAN L2TP connecton. Connected By: Dsplay the IP of remote connected clent. Acton: Act to the connecton. Clck Drop button to dsconnect the tunnel connecton. 31

32 L2TP Clent Name: The L2TP connecton name. Enable: Dsplay the connecton status wth cons. Status: The connecton status. Connecton Type: Remote Access or LAN to LAN. Peer Network IP: Dsplay the remote network and subnet mask n LAN to LAN L2TP connecton. Clent: Assgned IP by L2TP server. Acton: Act to the connecton. Clck Drop button to dsconnect the tunnel connecton. Refresh: Clck ths button to refresh the connecton status. GRE Name: The GRE connecton name. Enable: Dsplay the connecton status wth cons. Status: The connecton status, connected or dsable. Remote Gateway: The IP of remote gateway. Refresh: Clck ths button to refresh the connecton status. Log System Log Dsplay system logs accumulated up to the present tme. You can trace hstorcal nformaton wth ths functon. And the log polcy can be confgured n Confgure Log secton. Refresh: Clck to update the system log. Clear: Clck to clear the current log from the screen. 32

33 Securty Log Securty log dsplays the message logged about securty, lke flter messages and some frewall message. You can turn to IP Flterng Outgong, IP Flterng Incomng, URL Flter to determne f you want to log ths nformaton. Also you can turn to Confgure Log secton below to determne the level to log the message. You can use ths to track potental threats to your system and network. Refresh: Clck to update the system log. Clear: Clck to clear the current log from the screen. Confguraton When you clck ths tem, the column wll expand to dsplay the sub-tems that wll allow you to further confgure your router. LAN, Wreless, WAN, System, USB, IP Tunnel, Securty, Qualty of Servce, NAT and Wake On LAN. The functon of each confguraton sub-tem s descrbed n the followng sectons. 33

34 LAN - Local Area Network A Local Area Network AN) s a shared communcaton system network where many computers are connected. Ths type of network s area defned and s usually lmted to a confned regon wthn a buldng. Ethernet Parameters Group Name: Ths refers to the group you set n Interface IP address: the IP address of the router. Default s Subnet Mask: the default Subnet mask on the router. IGMP Snoopng: Enable or dsable the IGMP Snoopng functon. Wthout IGMP snoopng, multcast traffc s treated n the same manner as broadcast traffc - that s, t s forwarded to all ports. Wth IGMP snoopng, multcast traffc of a group s only forwarded to ports that have members of that group. 34

35 When enabled, you wll see two modes: Standard Mode: In standard mode, multcast traffc wll flood to all brdge ports when no clent subscrbes to a multcast group. Blockng Mode: In blockng mode, the multcast data wll be blocked when there are no clent subscrbes to a multcast group, t won t flood to the brdge ports. LAN sde frewall: Enable to drop all traffc from the specfed LAN group nterface. After actvatng t, all ncomng packets by default wll be dropped, and the user on the specfed LAN group nterface can't access CPE anymore. But, you can stll access the nternet servce. If user wants to manage the CPE, please turn to IP Flterng Incomng to add the allowng rules. Note that all ncomng packets by default wll be dropped f the LAN sde frewall s enabled and user cannot manage ths CPE from the specfed LAN group. DHCP Server You can dsable or enable the DHCP (Dynamc Host Confguraton Protocol) server or enable the router s DHCP relay functons. The DHCP protocol allows your router to dynamcally assgn IP addresses to PCs on your network f they are confgured to obtan IP addresses automatcally. Dsable Dsable the DHCP Server functon. Enable Enable the DHCP functon, enter the nformaton wanted. Here as default. Start IP Address: The start IP address of the range the DHCP Server used to assgn to the Clents. End IP Address: The end IP address f the range the DHCP Server used to assgn to the Clents. Leased Tme (hour): The leased tme for each DHCP Clent. Opton 66: Clck Enable to actvate DHCP opton 66 for some specal devces, lke IPTV Set Box. The devces can get frmware or some specal servce from the TFTP server. User needs to set the IP or hostname of the TFTP server. DHCP Server Relay DHCP Server IP Address: Please enter the DHCP Server IP address. 35

36 Statc IP Lst The specfed IP wll be assgned to the correspondng MAC Address lsted n the followng table when DHCP Server assgns IP Addresses to Clents. Press Add to the Statc IP Lst. Enter the MAC Address, IP Address, and then clck Apply to confrm your settngs. But the IP assgned should be outsde the range of IP Alas Ths functon allows the creaton of multple vrtual IP nterfaces on ths router. It helps to connect two or more local networks to the ISP or remote node. IP Alas: Check whether to enable ths functon. IP Address: Specfy an IP address on ths vrtual nterface. Subnet Mask: Specfy a subnet mask on ths vrtual nterface. Clck Apply to apply your settngs. IPv6 Autoconfg The IPv6 address composes of two parts, the prefx and the nterface ID. There are two ways to dynamcally confgure IPv6 address on hosts. One s stateful confguraton, for example usng DHCPv6 (whch resembles ts counterpart DHCP n IPv4.) In the stateful autoconfguraton model, hosts obtan nterface addresses and/or confguraton nformaton and parameters from a DHCPv6 server. The Server mantans a database that keeps track of whch addresses have been assgned to whch hosts. 36

37 The second way s stateless confguraton. Stateless auto-confguraton requres no manual confguraton of hosts, mnmal (f any) confguraton of routers, and no addtonal servers. The stateless mechansm allows a host to generate ts own addresses usng a combnaton of locally avalable nformaton (MAC address) and nformaton (prefx) advertsed by routers. Routers advertse prefxes that dentfy the subnet(s) assocated wth a lnk, whle hosts generate an "nterface dentfer" that unquely dentfes an nterface on a subnet. An address s formed by combnng the two. When usng stateless confguraton, you needn t confgure anythng on the clent. Group Name: Here group refers to the group you set n Interface Groupng secton, you can set the parameters for the specfc group. Select the group by the drop-down box. For more nformaton please refer to Interface Groupng of ths manual. Statc LAN IPv6 Address Confguraton Interface Address / Prefx Length: Enter the statc LAN IPv6 address. IPv6 LAN applcaton DHCPv6 Server: Check whether to enable DHCPv6 server. DHCPv6 Server Type: Select Stateless or Stateful. When DHCPv6 s enabled, ths parameter s avalable. Stateless: If selected, the PCs n LAN are confgured through RA mode, thus, the PCs n LAN are confgured through RA mode, to obtan the prefx message and generate an address usng a combnaton of locally avalable nformaton (MAC address) and nformaton (prefx) advertsed by routers, but they can obtan such nformaton lke DNS from DHCPv6 Server. Stateful: f selected, the PCs n LAN wll be confgured lke n IPv4 mode, thus obtan addresses and DNS nformaton from DHCPv6 server. Start nterface ID: Enter the start nterface ID. The IPv6 address composed of two parts, thus, the prefx and the nterface ID. Interface s lke the Host ID compared to IPv4. End nterface ID: Enter the end nterface ID. Note: Interface ID does NOT support ZERO COMPRESSION "::". Please enter the complete nformaton. For example: Please enter "0:0:0:2" nstead of "::2". 37

38 Leased Tme (hour): The leased tme, smlar to leased tme n DHCPv4, s a tme lmt assgned to clents, when expres, the assgned ID wll be recycled and reassgned. Issue Router Advertsement: Check whether to enable ssue Router Advertsement feature. It s to send Router Advertsement messages perodcally. ULA Prefx Advertsement: Enable ths parameter to nclude the pv6 ULA address n the RA messages. ULA, unque local address, s an IPv6 address n the block fc00::/7. It s approxmately the IPv6 counterpart of the IPv4 prvate address. They are not routable n the global IPv6 Internet. RADVD Type: The way that ULA prefx s generated. Randomly Generated Statcally Confgured: select to set manually n the followng parameters. Prefx: Set the prefx manually. Preferred Lfe Tme: The ULA prefx lfe tme. When the tme s over, the ULA prefx s nvald any more, -1 means no lmt. Vald Lfe Tme: It s a tme threshold, when the tme s over, clents should obtan new IPv6 address from the router through RA; -1 means to be lmtless. MLD snoopng: Smlar to IGMP snoopng, lstens n on the MLD conversaton between hosts and routers by processng MLD packets sent n a multcast network, and t analyzes all MLD packets between hosts and the connected multcast routers n the network. Wthout MLD snoopng, multcast traffc s treated n the same manner as broadcast traffc - that s, t s forwarded to all ports. Wth MLD snoopng, multcast traffc of a group s only forwarded to ports that have members of that group. Standard Mode: In standard mode, multcast traffc wll flood to all brdge ports when no clent subscrbes to a multcast group. Blockng Mode: In blockng mode, the multcast data wll be blocked when there s no clent subscrbes to a multcast group, t won t flood to the brdge ports. Stateless and Stateful IPv6 address Confguraton Stateless: Two methods can be carred. Wth DHCPv6 dsabled, but Issue Router Advertsement Enabled Wth ths method, the PCs n LAN are confgured through RA mode, thus, the PCs n LAN are confgured through RA mode, to obtan the prefx message and generate an address usng a combnaton of locally avalable nformaton (MAC address) and nformaton (prefx) advertsed by routers. Wth both DHCPv6 and Issue Router Advertsement Enabled Wth ths method, the PCs addresses n LAN are confgured lke above method, but they can obtan such nformaton lke DNS from DHCPv6 Server. 38

39 Stateful: two methods can be adopted. Wth only DHCPv6 enabled Wth ths method, the PCs addresses are confgured the same as n IPv4, that s addresses are assgned by DHCPv6 server. Wth both DHCPv6 and Issue Router Advertsement Enabled Wth ths method, the PCs addresses are confgured the same lke above, and the address nformaton n RA packets wll be neglected. Interface Groupng Interface groupng s a functon to group nterfaces, known as VLAN. A Vrtual LAN, commonly known as a VLAN, s a group of hosts wth the common set of requrements that communcate as f they were attached to the same broadcast doman, regardless of the physcal locaton. A VLAN has the same attrbutes as a physcal LAN, but t allows for end statons to be grouped together even f they are not located on the same network swtch. Each group wll perform as an ndependent network. To support ths feature, you must create mappng groups wth approprate LAN and WAN nterfaces usng the Add button. (Please Note: P4 can be confgured as EWAN, and when the devce s n EWAN profle, there s no P4/EWAN nterface as P4 s workng as a WAN port.) 39

40 Group Isolaton: If enabled, devces n one group are not able to access those n the other group. Clck Add to add groups. 40

41 Group Name: Type a group name. Grouped WAN Interfaces: Select from the box the WAN nterface you want to appled n the group. Grouped LAN Interfaces: Select the LAN nterfaces you want to group as a sngle group from Avalable LAN Interfaces. Automatcally Add Clents wth followng DHCP Vendor IDs: Enter the DHCP Vendor IDs for whch you want the Clents automatcally added nto the group. DHCP vendor ID (DHCP 60) s an Authentcaton for DHCP Messages. Clck Apply to confrm your settngs and your added group wll be lsted n the Interface Groupng table below. In group "test", P2 and PPP0.1 are grouped n one group, they have ther only network, see LAN. If you want to remove the group, check the box as the followng and press Remove. Note: - If you lke to automatcally add LAN clents to a WAN Interface n the new group add the DHCP vendor ID strng. - By confgurng a DHCP vendor ID strng any DHCP clent request wth the specfed vendor ID (DHCP opton 60) wll be dened an IP address from the local DHCP server. - If a vendor ID s confgured for a specfc clent devce, please REBOOT the clent devce attached to the modem to allow t to obtan an approprate IP address. - Each LAN nterface can only be added nto one group and one WAN nterface can only be used n one group. 41

42 Wreless 2.4GHz and 5GHz Ths secton provdes you ways to confgure wreless access. The TW-EAV510 AC v2 supports wreless on the 2.4GHz and 5GHz for users. Ths part has sub-tems as Basc, Securty, MAC Flter, Wreless Brdge, Advanced and Staton Info here. Please select whch one wreless you want to confgure. Basc It let you determne whether to enable Wreless functon and set the basc parameters of an AP and the Vrtual APs. Wreless: Default settng s set to Enable. If you do not have any wreless devces, check the checkbox agan to unselect. 42

43 Hde SSID: It s functon n whch transmts ts SSID to the ar so that when wreless clent searches for a network, router can then be dscovered and recognzed. Check the checkbox to determne whether you want to hde SSID. Clents Isolaton: f you enabled ths functon, then each of your wreless clents wll not be able to communcate wth each other. Dsable WMM Advertse: Stop the router from advertsng ts Wreless Multmeda (WMM) functonalty, whch provdes basc qualty of servce for tme-senstve applcatons (e.g. VoIP, Vdeo). Check to dsable or enable ths functon. Wreless multcast Forwardng (WMF): check to enable or dsable wreless multcast forwardng. SSID: The SSID s the unque name of a wreless access pont (AP) to be dstngushed from another. For securty purpose, change the default SSID to a unque ID name to the AP already bult-n to the router s wreless nterface. It s case senstve and must not excess 32 characters. Make sure your wreless clents have exactly the SSID as the devce, n order to get connected to your network. Note: SSID s case senstve and must not exceed 32 characters. BSSID: Basc Set Servce Identfer, t s a local managed IEEE MAC address, and s 48 bts value. Country: Dfferent countres have dfferent wreless band resources, so you can select the approprate Country accordng to your locaton. Max Clents: enter the number of max clents the wreless network can supports,1-16. Guest/vrtual Access Ponts: A Vrtual Access Pont s a logcal entty that exsts wthn a physcal Access Pont (AP). When a sngle physcal AP supports multple Vrtual APs, each Vrtual AP appears to statons (STAs) to be an ndependent physcal AP, even though only a sngle physcal AP s present. For example, multple Vrtual APs mght exst wthn a sngle physcal AP, each advertsng a dstnct SSID and capablty set. Alternatvely, multple Vrtual APs mght advertse the same SSID but a dfferent capablty set allowng access to be provded va Web Portal, WEP, and WPA smultaneously. Where APs are shared by multple provders, Vrtual APs provde each provder wth separate authentcaton and accountng data for ther users, as well as dagnostc nformaton, wthout sharng senstve management traffc or data between provders. You can enable the vrtual AP. Here you can enable some Vrtual APs accordng to the request. And the other parameters of vrtual APs are the same to the above. Clck Apply to apply your settngs. Securty Wreless securty prevents unauthorzed access or damage to computers usng wreless network. Note: The WPS feature wll also be unavalable when the securty settng s not WPA2 or OPEN. So, f you manually set the wreless securty settng, you should gve notce to t, but you can fnd prompt ndcatng confguraton. 43

44 Manual Setup AP Select SSID: Select the SSID you want these settngs apply to. Network Authentcaton Open WEP Encrypton: Select to enable or dsable WEP Encrypton. Here select Enable. Encrypton Strength: Select the strength, 128-bt or 64-bt. Current Network Key: Select the one to be the current network key. Please refer to key 1-4 below. Network Key (1-4): Enter 13 ASCII characters or 26 hexadecmal dgts for 128-bt encrypton keys. Enter 5 ASCII characters or 10 hexadecmal dgts for 64-bt encrypton keys. Shared Ths s smlar to network authentcaton Open. But here the WEP Encrypton must be enabled. 44

45 802.1x RADIUS Server IP Address: RADIUS(Remote Authentcaton Dal In User Servce), Enter the IP address of RADIUS authentcaton server. RADIUS Server Port: Enter the port number of RADIUS authentcaton server here. RADIUS Key: Enter the password of RADIUS authentcaton server. WEP Encrypton: Select to enable or dsable WEP Encrypton. Here select Enable. Current Network Key: Select the one to be the current network key. Please refer to key 2-3 below. Network Key (1-4): Enter 13 ASCII characters or 26 hexadecmal dgts for 128-bt encrypton keys. Enter 5 ASCII characters or 10 hexadecmal dgts for 64-bt encrypton keys. WPA WPA Group ReKey Internal: The perod of renewal tme for changng the securty key automatcally between wreless clent and Access Pont (AP). Ths s n seconds. RADIUS Server IP Address: RADIUS( Remote Authentcaton Dal In User Servce), Enter the IP address of RADIUS authentcaton server. RADIUS Server Port: Enter the port number of RADIUS authentcaton server here. RADIUS Key: Enter the password of RADIUS authentcaton server. WPA/WAPI Encrypton: There are two Algorthms, AES (Advanced Encrypton Standard) and TKIP(Temporal Key Integrty Protocol) whch help to protect the wreless communcaton. WPA-PSK / WPA2-PSK 45

46 WPA/WAPI passphrase: Enter the WPA.WAPI passphrase; you can clck here to dsplay to vew t. WPA Group ReKey Internal: The perod of renewal tme for changng the securty key automatcally between wreless clent and Access Pont (AP). Ths s n seconds. WPA/ WAPI Encrypton: There are two Algorthms, AES (Advanced Encrypton Standard) and TKIP (Temporal Key Integrty Protocol) whch help to protect the wreless communcaton. WPA2 WPA2 Preauthentcaton: When a wreless clent wants to handoff to another AP, wth preauthentcaton, t can perform 802.1X authentcaton to the new AP, and when handoff happens, ths mode wll help reduce the assocaton tme. Network Re-auth Interval: the nterval for network Re-authentcaton. Ths s n seconds. WPA Group ReKey Internal: The perod of renewal tme for changng the securty key automatcally between wreless clent and Access Pont (AP). Ths s n seconds. RADIUS Server IP Address: RADIUS(Remote Authentcaton Dal In User Servce), Enter the IP address of RADIUS authentcaton server. Ths s n seconds. RADIUS Server Port: Enter the port number of RADIUS authentcaton server here. RADIUS Key: Enter the password of RADIUS authentcaton server. WPA/WAPI Encrypton: There are two Algorthms, AES (Advanced Encrypton Standard) and TKIP (Temporal Key Integrty Protocol) whch help to protect the wreless communcaton. Mxed WPA2/WPA WPA2 Preauthentcaton: When a wreless clent wants to handoff to another AP, wth preauthentcaton, t can perform 802.1X authentcatons to the new AP, and when handoff happens, ths mode wll help reduce the assocaton tme used. Network Re-auth Interval: the nterval for network Re-authentcaton. The unt s second. WPA Group ReKey Internal: The perod of renewal tme for changng the securty key automatcally between wreless clent and Access Pont (AP). Ths s n seconds. RADIUS Server IP Address: RADIUS (Remote Authentcaton Dal In User Servce), Enter the IP address of RADIUS authentcaton server. RADIUS Server Port: Enter the port number of RADIUS authentcaton server here. RADIUS Key: Enter the password of RADIUS authentcaton server. 46