Installation of hard drive (2.5 or 3.5 inch)

Transcription

1 Safety Warning This product has been manufactured to comply with international safety standards. Please read the following safety precautions carefully. Safety instructions and Precautions 1. MAINS SUPPLY Operate this product only from the type of power supply indicated on the marking label. Disconnect the product from the mains before you start any maintenance or installation procedures. 2. OVER LOADING Do not overload a wall outlet, extension cord or adapter as this may result in electronic fire or shock 3. LIQUIDS The product should not be exposed to liquid of any kind. In addition, no objects filled with liquid should be placed on the product. 4. VENTILATION The slots on rear of the product must be left uncovered to allow proper airflow into the unit. Do not stack electronic equipments on top of the product. 5. ATTACHMENTS Do not use any unsupported attachments as these may be hazardous or cause damage to the product. 6. CONNECTION TO THE TV Disconnect the product from the mains before connecting or disconnecting the cable from the TV. Failure to do so can damage the TV. 7. LOCATION Place the product indoors to avoid exposing it to lightning, rain or sun. Do not place it near a radiator or heat register. 8. REPLACEMENTS OF PARTS When replacement of parts is required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitution may result in additional damage to the unit. CAUTION Back up your system periodically to avoid any potential data loss. We disclaims any responsibility of all sorts of data loss or recovery

2 Installation of hard drive (2.5 or 3.5 inch) 1. The top and bottom case come already assembled. Remove the five fixing screws on bottom case as shown in the picture below. 2. Remove the top case by lifting it up in the direction shown below. 3. Take the drive chassis out of the bottom case after removing the two fixing screws on both sides of chassis.

3 4. Place the drive on its position of chassis, line up the holes and then insert the fixing screws supplied. 3.5" drive: line up the holes shown 12 and fix the screws in the direction shown in the picture 2.5 drive: line up the holes shown 3456 and fix the screws in the direction shown in the picture. 5. Insert the chassis into the case and then plug in the hard drive to the connector in the direction shown 1. Secure the chassis to the bottom case by fixing the screws on both sides of chassis in the direction shown 2 6. Assemble top cover with bottom cover by fixing the five screws

4 CONTENTS 1 Before using the product Package Contents Front View Side View Rear Panel Remote Control 9 2 Connections Connect to the Antenna To use the composite AV connector To use HDMI connector Plug in power Connect to the Ethernet To use optical Digital Audio Connect a USB device Transfer media files from your computer to player To use AV Input connector To use the SD card 13 3 Basic Operation Browser Menu Movie Playback Music Playback Viewing Photos 16 4 Installation (Searching for the channels) Automatic Search Manual Search 19

5 5 Recording Instant Recording Scheduled Recording by manual Scheduled Recording by EPG (Electronic Program Guide) Recorded Program Time Shifted Recording 24 6 File Manager Copy or Move Delete 26 7 Network Setup Wired Setup Wireless Setup (Optional) Browsing on the network Using Internet Radio FTP Server NFS Server BitTorrent 37 8 Setup 39 9 Firmware Update Partition and Formatting of hard disk Appendix Trouble shooting Specification 50

6 1. Before using this product This chapter provides detailed instructions on the product and its accessories. 1.1 Package Contents Check all the package contents before using the product. Recorder Remote Control Batteries Users Manual AC adapter Power Cord USB Cable Composite audio/video cable NOTE Product contents may be subject to change. Cables not specified above must be purchased separately

7 1.2 Front View 1. Power LED The power LED on the front of the unit is on while the recorder player starts up. 2. Infrared receiver Receives signals from the remote control. Make sure that the path between remote control and IR is unobstructed. 1.3 Side View 3. SD card slot 4. USB Host port 5. FAN 5

8 1.4 Rear Panel 1. DC12V 2. USB(PC) Target Port 3. HDMI Out 4. LAN(Ethernet 100Base-Tx/10Base-T) 5. ANTENNA-IN for TV Tuner(DVB-T) 6. ANTENNA-OUT for TV Tuner(DVB-T) 7. OPTICAL Out 8. AV-OUT (stereo audio and composite video output) 9. AV-IN 6

9 1. POWER Standby mode 2. TV OUT Switch TV OUT mode. 3. SOURCE Press the button to change the input signal SOURCE. 4. REC. -. Press the button to begin recording -. Press the button to resume recording -. Press the button to use instant recording function 5. TIME SHIFT Press the button to use Time Shift function 6. SETUP Press the button to go directly to SETUP Menu 7. Number button -. Press to change the channel. -. Press to enter numeric changing settings. 8. Press the button to move to next or previous file 7

10 9. MUTE Mute the audio temporarily. 10. STOP Press to stop playing a file 11. PLAY/PAUSE -. Press the button to play a file -. Press the button again to stop the current file -. Press the button to resume playback of this file. 12. VOL + / - Adjusts the audio volume. 13. HOME Home screen which displays RECORD/AV IN/FILE MANAGER/SETUP. 14. ARROW Press the buttons to navigate the menus. 15. OK Press the button to select a menu or confirm the user s action. 16. REW / FF -. Press the buttons to rewind/forward the playback of recorded file. -. Press repeatedly to select faster REW/FF speeds. 17. RETURN -. Goes back to the previous screen -. Press the button to cancel user s action. 18. INFO Press the button to display the information of recording. 19. EPG Press the button to display the Electronic Program Guide. (for NTR82 and NTR83 only) 20. MEDIA Navigate through All,, Movies, Music or Photo icons on Browser menu 8

11 21. EJECT Safely remove attached storage 22. i-radio Goes directly to folder named Internet Radio 23. GOTO Press the button to go to a specific point. 24. SLOW Press the button to change the playback speed into the slow motion mode. 25. A - B Press the button to set the beginning and end points of a section to repeat 26. SHUFFLE Press the button to switch random and sequential playback. 27. ZOOM Press the button to zoom in/out the screen during watching a file. 28. ROTATE Press the button to rotate a picture by 4 angles. 29. BOOK MARK Press the button to add or delete the current position as a bookmark. 30. SLEEP Press the button to set the timing to turn the product off automatically. 31. DVD MENU Press the button to display DVD menu. 32. AUDIO Press the button to view the audio track. 33. S. TITLE Press the button to view subtitles 34. SYNC Press the button to synchronize the video and subtitle 9

12 2. Connections 2.1 Connect to Antenna Connect your aerial to ANTENNA-IN outlet on the rear of recorder player. And connect the ANTENNA-OUT outlet of the unit and the aerial input of TV using RF cable. 2.2 To use the composite AV connector Plug the yellow(video), red(right audio) and white(left audio) connectors into their respective ports on the player. Plug the opposite ends into the composite input ports on your television

13 2.3 To use HDMI connector Plug one end of the cable into the HDMI socket on the recorder player, and plug the other end into the matching socket on your television. In this case, you do not have to make audio connection because the HDMI connector can output stereo audio or Dolby Digital audio. 2.4 Plug in power Connect the power cable to the media player s DC connector, and then plug the opposite end into an AC power outlet. 2.5 Connect to the Ethernet Connect one end of the Ethernet cable into the LAN outlet on the rear of the recorder player and the other into your computer network switch or router

14 2.6 To use optical Digital Audio Plug the optical cable into the digital optical port on your player and the other end of the optical cable into the digital optical port on you re a/v receiver. 2.7 Connect a USB Device The player has two USB ports that support playback from the USB external drives. Connect the USB device to either of the HD media player s USB ports

15 2.8 Transfer media files from your computer to player Connect your player to your computer and transfer your favorite contents from your computer to your recorder player. Safely remove the player from your computer. 2.9 To use AV input connector Use the composite cable when connecting to a DVD player and other audiovisual equipment To use the SD card Insert a SD card into the SD card socket of your recorder player

16 3. Basic Operation 3.1 Browser Menu Home screen menu is displayed when your press HOME on the remote control. The icons on the Browser menu (default) let you to browse your media library. The Movies, Music and Photo icons represent files for the different media types. All icon will display available media files in the current folder. 3.2 Movie Playback Select Movies icon by pressing MEDIA on remote control. The screen will display available video files. You can navigate video files by using buttons to scroll through the list To begin playback of a single file, highlight the file and then press OK. Video Play Controls Use these buttons on the remote control to control video playback. Button Function Stops video playback Pause or resume video playback Resume playback on the selected position(video scan) Scan video (press repeatedly to select the scan speed)

17 Using Video Repeat Use this option to repeat the video currently playing. To set the video repeat mode : 1. During video playback, press SHUFFLE. The option appears on the top of the screen. 2. Press repeatedly until the repeat mode you want is displayed. Options include : OFF The video file(series file) will be just repeated once. Repeat The current video is played repeatedly until you press STOP All All the files in the current video folder are played in sequence, and repeatedly, until you press STOP Displaying the Video information panel Use this option to display the video information panel on the top of screen. To view the Information Panel of current video, press button during the video playback. 3.3 Music Playback Select Music icon by pressing MEDIA on remote control. The screen will display available audio files. You can navigate audio files by using buttons to scroll through the list. Music Play Controls Use these buttons on the remote control to control music playback. Button Function Stop audio playback Playback audio file Scan the audio playback forward or backward

18 Music Shuffle Mode Use this option to set the audio tracks in the current music folder to play in random order. To enable music shuffle mode : 1. During music playback, press SHUFFLE. The option opens at the top of screen. 2. Press repeatedly until the shuffle mode you want is displayed. Options include : OFF All the audio tracks in the current folder are played in sequence, and once, until you press STOP Shuffle Repeat All 3.4 Viewing Photos Once Select Photo icon by pressing MEDIA on remote control. You can navigate image files by using buttons to scroll through the list You can navigate previous or next 10th image file from the one in the current list by using buttons Photo Slideshow This player allows you to create a slideshow using the contents of a photo folder. To start a slide show: 1. Select the photo folder containing the image files you want in the slide show. 2. Highlight the image files in the current folder, then press PLAY/PAUSE to start the slideshow

19 To listen to background music with a slideshow: 1. Select the audio files you want to accompany the slide show 2. Copy them into the photo folder you want in the slide show To listen to background music with a slideshow, the audio files and pictures must be included in the same folder. Repeating a Slideshow Use this option to set the slideshow to play in a loop sequence. To set the slide show repeat mode: During the slideshow, press REPEAT/SHUFFLE, then press this button repeatedly until the repeat mode you want is displayed. Options include: Not repeating: The slideshow is played once Change status to repeat: The slideshow is played repeatedly until you press STOP Photo Display Options Rotating the Picture Use this option to rotate the image clockwise. This setting does not affect the original file s orientation. During the photo viewing, press ROTATE, then press this button repeatedly until the rotation you want is set. Using Photo Zoom Use this option to change the viewing scale of the image display. During the photo viewing, press ZOOM, and then press this button repeatedly until the scale you want is shown. Displaying the Picture information panel Use this option to display the Picture Information Panel on the top of the screen. This panel shows the following information about the current picture: Image file name Image s sequence number and the total number of image files in the current folder

20 4. Installation(Searching for the channels) This will guide you through the installation procedure to automatically search for the digital channels. You will also run this installation after the product has been returned to the Factory Reset. 4.1 Automatic Search Wait while channel search continues. This may take a few minutes. 1. Select Channel Scan and then press OK 2. During the channel search, the cursor is located at CANCEL. Therefore, if you press OK button during the search, the search will stop and the channels found until then will be displayed. 3. If the search does not find any channels, then select Channel Scan button to search for the channels again. Make sure that you have connected your aerial correctly

21 4. You can delete the unwanted channels from the found channels. NOTE If you exit the installation without fully completing the channel searching procedure, you may not have all of the channels available. In this case, you can use channel scan menu to search for the channels. 4.2 Manual Search You can search channels manually by searching parameters. 1. Press HOME, press the SETUP icon and then the screen like the left figure will be shown. 2. Select Channel Scan, highlight MANUAL SCAN and then press OK. 3. Enter the channel to search. When entering channel value, the appropriate frequency value is displayed

22 5. Recording The product provides various recording modes such as instant recording and scheduled recording. It supports standard DTV features such as EPG (Electronic Program Guide) and Time shifting. 5.1 Instant Recording The instant recording function records the channel displayed currently. 1. Press the REC button to record current channel instantly. 2. Press the REC button repeatedly until the recording duration you want is displayed. Options includes : REC OFF REC 30 min 60 min 90 min 120 min 180 min 240 min 3. Press button to see the detailed information about the recorded program. 4. Press button to stop recording the current channel. 5. If you move to other channel, stops instant recording. Do not switch channels while recording using this function. Note : Ensure that there is enough free space before recording. If the free space on the hard disk drive is insufficient, recording will stop. Recording one hour of program may require up to 2 or 3GB of hard disk space. The first partition of the local hard disk drive must be formatted in NTFS. The recorded program is saved in the folder named My Recordings

23 5.2 Scheduled Recording by manual You can set a service to be recorded at a specific time. Even if the player is in standby mode, it will switch into operation mode and start recording at a specified time. 1. Press HOME, select Record Schedule and then press OK. 2. Select Add a new schedule and press OK to add a new timer event. 3. The box like the left figure will be shown. Set the Type, Date, Duration, Cycle, Quality by using,,,. 4. The following message will be shown. Select Yes to save the changes. 5. This player will be turned on automatically around three minutes before the scheduled timing

24 5.3 Scheduled recording by EPG(Electronic Program Guide) With the Electronic Program Guide (EPG), you can check the schedule of DTV service or event, view detailed information about them. DTV EPG function is not available in analog TV or external input device. Press EPG button to record or see the desired service or event General EPG Screen 1 Service list Shows the list of all services currently available. As you press button, the rows in the event name list will be refreshed correspondingly. 2 ~ 3 Event name list Shows the names of current events in a grid of rows and columns. You can check scheduled event information up to several days ahead, depending on conditions. 4 Picture window 5 Event name Press to open or close EPG Screen Press to change the service list Press to move EPG date forward Press to move EPG date backward

25 Press to scroll up the event name list Press to scroll down the event name list Press to record the desired channel in DTV mode 5.4 Recorded program 1. Press RECORD SCHEDULE button. 2. Select STATUS by using / button. The recorded program list will appear. Note : The program being recorded will be added to the recorded program list The start time of scheduled recording cannot be set within the duration of scheduled recording to start first. Lock Ready Displayed when the program is being recorded. No deleting and editing is feasible. Displayed only if the program is reserved for recording 3. Select the desired reservation using / and press OK. 4. The following popup menu will appear and you can pause scheduled recording

26 1. Move to Delete icon. 2. After selecting reserved program using /, press OK. 3. The following popup menu will appear and then press Yes. Note: If the status of reserved program is set to Lock, you cannot delete the program. 1. Move to History icon. 2. Press OK by using /, to delete a recorded program. OK Displayed if the recording is completed successfully FAIL Displayed if the program fails to be recorded 5.5 Time Shifted Recording You can perform Time Shifted recording while watching the currently broadcasting TV program. If you press the TIME SHIFT button on the remote control, the current program is paused. And the program is resumed from that point If you press the INFO button while watching TV, the time bar information will be displayed. Time bar displays the time gap between the broadcasting point and watching point and the amount of temporarily saved program. Note: Time shift makes the time gap between the broadcasting (live) point and watching point. Press the STOP button to go to the live program

27 6. File Manager This section describes how to copy, move or delete the files or folders from one storage device to another one. 6.1 Copy or Move 1. Press HOME and select File Manger icon. 2. Select source storage and press OK. 3. Select the folders or files you want to copy or move, press PLAY/PAUSE and then the screen like left figure will be shown. 4. Press and then select destination storage. 5. Locate the folder to copy or move the selected files or folders and press. The message like left figure will be shown. Select Copy or Move and then press OK Item with V displayed in red indicates it is currently selected. Select want to create New Folder? to create a new folder into the destination storage. Enter Folder Name by using,,, and then select OK

28 6.2 Delete 1. Press HOME and select File Manger icon. 2. Select source storage and press OK. 3. Select the folders or files you want to delete, press PLAY/PAUSE and then the screen like left figure will be shown. 4. Press and the screen like left figure will be shown. Select Recycle Bin icon and then press OK. 5. The following message will be shown. Highlight Delete and press OK

29 7. Network Setup This chapter will guide you through the network settings such as wired, wireless and FTP. 7.1 Wired Setup DCHP(AUTO) If your network supports DHCP, set this option to receive an automatic IP address and subnet mask assignment. 1. Press HOME and select Setup icon. 2. Select Network icon and press OK. 3. Select Wired Setup and press OK. 4. Select DHCP IP and press OK 5. Select OK, press OK. A confirmation prompt appears and select OK to save setting. NOTE: You may enter DNS server IP manually depending on the router available Static IP (Manual) Use this menu to manually configuring the IP address, Subnet mask, Default Gateway, DNS Server IP. 1. Select Static IP and press OK. 2. An on-screen menu opens 3. Enter IP addresses, Subnet Mask, Default Gateway, DNS Sever (Provided by your ISP) by using the NUMERIC (0 ~ 9) buttons and press OK. 4. A pop will appear and press OK to apply changes

30 7.2 Wireless Setup(Optional) This section allows you to make changes to the wireless network settings. 1. Connect USB Wi-Fi adapter to USB host port of this player. 2. Press HOME and select Setup icon. 3. Select Network icon and press OK. 4. Select Wireless Setup and press OK. 5. Select Infrastructure (AP) and press OK. 5. Select AUTO and press OK. List of Access Points (AP) will be displayed available within your range. Select the AP you connect to and press OK. 6. If the security is enabled on the AP you connect to, an on-screen keyboard will be shown. Enter the encryption key by using / / / and then select OK. 7. The following message will be shown when the wireless connection is configured But, if encryption key is wrong or the AP does not match with the setting, the failure message will be shown. NOTE: If your wireless signal seems week in some spots, place your router as close as possible to USB module. If you play high definition files over wireless connection, you may experience the stutter. If you use an USB Wi-Fi adapter with other USB device, it may not work properly

31 7.3 Browsing on the network This section describes how to playback the multimedia files shared on the local area network (Ethernet or WLAN). Make sure that this player is connected on the network. 1. Press HOME and select Browser icon. This icon on this screen lets you browse your media library. 2. Select Network icon and press OK. 3. Workgroup lists will be displayed on your network. Locate the workgroup and all the shared files and folders available will be displayed on the screen. Windows XP(Win2000 server) User To access the shared folder, enable Guest Account. 1 Double click Computer Management. 2 Open Local Users and Groups and expand the Users folder. 3 Double click Guest, and the Guest Properties window will appear. Make sure that the check mark next to account is disabled. 4. To begin playback of the file you want, highlight it and the press OK. NOTE You can turn the firewall function off if needed. It may take several minutes, to load and play the shared media files depending on the network connection and size of shared media files

32 7.4 Using Internet Radio 1. Create a folder in the hard drive by connecting to a PC. 2. Visit the directory of community free online radio station (e.g. to enjoy internet radio with this player 3. If you find a radio station, choose save target as to save it to the folder. This player currently supports M3U and PLS audio formats only. 4. You can remove unnecessary items from the PLS file by using the program such as Word pad in your PC 5. Disconnect the player from the PC. 6. Make sure that the player is connected to wired or wireless LAN. 7. Press HOME. To listen to the favorite internet radio, select folder > internet radio from Browser menu, and then press OK. When you press i-radio on remote control, it will display the station lists in the Internet Radio folder you create. NOTE: LAN connection required for access to internet radio station. The radio station needs to be saved as M3U or PLS format to include streaming URL

33 7.5 FTP Server This menu allows you to determine how to copy, move and delete the files between PC and this player on the network. Make sure that the network settings are correct and FTP client program is installed on your PC to use FTP service 1. Press HOME and then select Setup icon. Use the right navigation button to select a Network icon, and press ENTER. 2. If the network is set to DHCP, IP addresses (e. g xxx. xxx) will be assigned automatically from router. The IP addresses may vary, depending on your network settings. 3. Select FTP User Name to change User Name, and press OK. An on-screen keyboard opens. 4. Enter User Name using / / / button and then press OK. 5. Select FTP Password to change Password, and then press OK. An on-screen keyboard opens 6. Enter NEW Password using / / / button and then press OK. 7. Enter NEW Password again to confirm verify password, and press OK. The default FTP User Name is guest and default password is

34 To use FTP service, make sure FTP client program is installed on your PC. You can download legal FTP client software (e.g. FileZilla) and install it on your PC. The following explains how to use FTP service by using FileZilla software 8. When you have installed FileZilla and run this software from the installed location, the screen like the left figure is shown. 9. To log on the FTP server, you must type host, user name and password and define the port number (default: 21) as shown below. NOTE: For the detailed use of FileZilla, refer to the online help of the website of this software. 10. When you log on the FTP server, the screen on the left will be shown. The folders and files on the player will be shown on the right window. 11. Drag the files and drop them to the folder directly to transfer. You can view the realtime status of file transfer as shown below. ** NOTE ** 1. It is needed to limit the maximum number of connections for a single account for the proper operation. 2. Network connection may be disabled depending on connectivity of FTP available during the uploading of highresolution files

35 7.6 NFS Server This player can also work as NFS server. You can download the NFS server program and configure the following settings (Windows XP) 1. To use NFS Server, you can download the latest Microsoft Windows Services for Unix software from official Microsoft website. 2. Unzip the file you downloaded and double-click on the icon labeled setup.exe. 3. Click Custom Installation to specify the components that you want to install or specify a different installation location. And then click Next. 4. Choose the components of Microsoft Windows Services for UNIX that you want to install. Click Server for NFS and Server for NFS Authentication. 1 This indicates that the component you want will be installed on local drive. 2 This indicates that the component will not be available

36 5. If the User Name Mapping page is displayed, click Password and group files and then click Next. 6. Setup installs Microsoft Windows Services for UNIX. This will take a few minutes. 7. Click Finish one the Completing the Microsoft Windows Services for UNIX Setup Wizard page. 8. Create the two dummy files called passwd and group in SFU folder (c:/sfu). Type root::0:0:root::/bin/sh in dummy file called passwd and root:x:0: in dummy file called group

37 9. Run the installed Services for UNIX Administration. Click Configuration tap. Click Browse and then enter passwd in Password file path and name. Click Browse and then enter group in Group file path and name 10. Click the Maps tab. Click Show User Maps in order to map user names. 11. Click the List Windows Users and Windows users available will be displayed. In the Windows user box, click Windows user name to log on the Windows. (example: Administrator, User) 12. Click the List Linux Users and click root. 13. Click Add and then user name will be displayed in the mapped user list. 14. Click Apply to save settings

38 15. Right-click on the folder you want to share and select Properties from the drop-down menu. 16. Under the NFS Sharing tab, click Share this folder. 17. Type your name in Share name box (default: nfs) 18. Select Read-Write under Type of access. Make sure that Allow root access box is checked 19. Press HOME and then select SETUP icon. 20. Select NFS server IP address > NFS Setup. Type IP address of the computer which you installed Microsoft Windows Services for Unix

39 21. Select Share name > NFS Setup. An onscreen keyboard opens. Enter the share name of folder you configured in the PC directly using on-screen keyboard. 22. Press HOME and then select Browser icon. You can play the shared files by selecting NFS icon. NOTE: If multiple Windows user names are mapped to one UNIX user name, you must select one map to be primary You can install other NFS server software as you desired. You can contact them on the technical support information. 7.7 BitTorrent This player can work as BitTorrent client. You can download legal torrent files by searching on the Internet. There are websites that provide legally sharing torrents e.g. The websites offer torrents as one method of downloading files. It is recommended to format hard disk by selecting HDD format > System from Setup menu. Otherwise, BitTorrent client may not work properly with this player. Back up your valuable data before formatting the hard disk 256MB Linux SWAP partition is created automatically if formatting is complete. Two folders called Download and Torrent are automatically created in the first partition of hard disk when selecting Torrent icon > File Manager menu 1. Browse the torrent files on the website and save the files (.torrent) to your PC 2. Connect the player to PC and copy the saved torrent files to Torrent folder of player