How To Sail A Winner Optimist
|
|
|
- Milo Doyle
- 5 years ago
- Views:
Transcription
1 Rigging Manual Winner Optimist Congratulation on the purchase of your new Winner Optimist. Reading this manual will help you with the rigging and preparation for correct use and subsequent high enjoyment that comes with the Winner Optimist. No tools are required for the rigging, as the Winner Optimist comes almost prepared for sailing. The Optimist and key parts: 1
2 This manual includes the fitting and preparation of the following parts of the Optimist: 1. Sprit halyard 2. Sprit 3. Sail 4. Mast collar 5. Mast step 6. Boom 7. Boom outhaul 8. Boom downhaul 9. Mainsheet 10. Dagger board 11. Rudder 12. Practical use 13. Good advise
3 1. Sprit Halyard. Attach the sprit halyard to the mast clam cleat. Secure the halyard in the clam cleat with a stopper knot. The sprit is fastened with a downward pull in the halyard. The block-in-wire system is to be fitted at the other end of the sprit halyard thereby connecting the clam cleat at the mast with the block-in-wire system. 2. Sprit Place the rounded end of the sprit into the loop at the end of the block-in-wire system. The sprit is now adjustable and must be adjusted according to wind conditions, using the sprit halyard. 3. Sail. Spread out the sail on the floor, place mast and boom according to the illustration. Attach the sail to the mast and boom with sail ties. Be sure to use at knot with extra overhand on top of it. Use thicker sail ties (3 mm), and wrap them around twice, at the end of both the mast and boom for extra strength. At top of the mast, an sail tie must be wrapped around diagonal to secure the lower top pin. Wrap a 3mm tie around the mast twice to secure the upper top pin. Put the wind indicator through the two pins. 3
4 4. Mast collar. All Winner Optimist comes with mast sleeve fixed. Depending on which mast your Winner Optimist is equipped with, the mast sleeve will be either with or without a mast collar. Club rigs usually come without the mast collar, but racing rigs comes with. Does your Optimist have a mast sleeve with collar, the collar must be fitted to the mast, which then fits into the mast sleeve. The mast fits right into the mast sleeve on Optimists without collar. (Illustration show mast sleeve without collar) 5. Mast step The mast is placed in the mast step. The mast step is adjustable, and can be adjusted specially to the sail being used, in order to achieve the best performance. 6. Boom The boom must be secured to the mast. Wrap the rope at the base of the boom around the little knob on the mast. The rope is attached at each arm of the boom jaw. When de-rigging, it is best to pull the boom upwards towards the mast, and thereby automatically release the boom fork form the mast. 4
5 7. Boom outhaul Tie a stopper knot at one end of the outhaul and put the other end forward through the port hole in the outboard end of the boom. Pass the outhaul through the corner of the sail, then back through the starboard hole and then forward to the clam cleat. Secure the end with a stopper knot. 8. Boom downhaul Fasten the downhaul rope to the wire hanging from the boom. Lead the downhaul rope down to the clam cleat on the mast and pass it up from underneath. Secure the rope with a stopper knot. 9. Mainsheet Attach the boom bridle to the two boom bridle buttons located on the boom. Attach the mainsheet to the ring on the boom bridle. 5
6 10. Dagger board The dagger board is placed in the dagger case. Use the rubber band to secure the dagger board while sailing. Remember to fasten the dagger board to the boat with a piece of rope. Fix the rope using the hole in the dagger board and secure the other end at the eye, which is also used to hold the rubber band in place. Important: The sharp edge of the dagger board must face backwards. 11. Rudder The rudder is fitted to the two rudder angles at the back of the boat. Make sure the safety snap has clicked the rudder into position. To remove the rudder, then push the safety snap in to release the rudder from the boat. 6
7 12+13: Practical use & good advise Handling & maintenance of the Winner optimist When buying a Winner Optimist you get a refined sport implement, built within the tolerance of the class rules, the intention to attain the best possible competition effect. Please handle your dinghy with extra care as it is constructed with competition in view and this does not stand the same kind of handling as an ordinary dinghy. To get the optimal pleasure of your dinghy, kindly note the following advises regarding the handling. Failure of correct handling will affect the performance of the boat and perhaps cause permanent damages and defects for which we are not responsible. Please observe the following: Advise: To be stored frost proof. Take care that the bottom is not put under spot pressure. Do not cover with PVC cover, plastic or similar, which does not permit water diffusion. Do not grind on gel-coat layer. Any major reparation of the boat - which involves grinding and remodelling is only to be carried out by Winner or the guarantee repeals. Only polish by hand using approved boat wax. In case of damages and fractures of the gel-coat layer, the fibreglass lamination must be prevented from absorbing water. Do not expose the boat to high heating stresses. Clean, polish and wax the boat at least once a year. Always use a lifejacket and only sail under supervision of fully qualified adults. Wash your boat with fresh water after use. Stored in a dry place. Do not over-inflate the airbags they may burst in the sun. Lifting your Optimist: Empty the boat for water and equipment. Lift only your boat by the outer gunwale. Stored on a padded surface. Transporting your Optimist: Make sure that the roof-racks are securely mounted on the car. Transport your Optimist upside down. And best with a top and bottom cover which protects the boat from dirt, stone throw and save fuel!) Do not tie the Optimist too tight to the roof racks it prevents small cracks in the gel coat. Check the height of garage before parking your car with the boat on top of it If you follow these instructions you should be sure to enjoy your Winner optimist for many years. 7
Rigging Manual. 1 Parts of the Hull. 2 Parts of the Sail. 3 Sunfish Mast Kit. 4 Bailer Installation. 5 Ratchet Block Installation
SUNFISH SUNFISH RACE SUNFISH Rigging Manual 1 Parts of the Hull Go-fast tip number one: Read this rigging guide first. 2 Parts of the Sail 3 Sunfish Mast Kit 4 Bailer Installation 5 Ratchet Block Installation
THE FLYING SCOT A BASIC GUIDE TUNING AND SAIL TRIM By Harry Carpenter
THE FLYING SCOT A BASIC GUIDE TO TUNING AND SAIL TRIM By Harry Carpenter Tuning the Flying Scot Rig Boat set up In setting the mast rake on a Flying Scot, most Scot sailors run a tape measure up the mast
Learn to Sail at MIT
Learn to Sail at MIT Please read this before the next class and practice your knots: the bowline and the stunsail tack bend. Rigging Check with the dock staff to see if there are any restrictions. Grab
EH-20 20m antenna. By VE3RGW
EH-20 20m antenna By VE3RGW Equivalent circuit of EH-20 (prototype 2A) antenna system. Upper cylinder Lower cylinder Ground Counter pose Phasing coil Impedance transformer and tune circuit Tune coil Feed
NONSUCH SPARS Recommended Owner s Maintenance Schedule
NONSUCH SPARS Recommended Owner s Maintenance Schedule The first Nonsuch masts were designed and produced in 1978 and these prototype spars are standing and functioning today after seven seasons of hard
RS300 OWNER S MANUAL. LDC Racing Sailboats, Trafalgar Close, Chandlers Ford, Eastleigh SO53 4BW, GBR Tel. +44 (0)23 8027 4500 Fax. +44 (0)23 8027 4800
RS300 OWNER S MANUAL LDC Racing Sailboats, Trafalgar Close, Chandlers Ford, Eastleigh SO53 4BW, GBR Tel. +44 (0)23 8027 4500 Fax. +44 (0)23 8027 4800 INTRODUCTION Congratulations on the purchase of your
Micrio WS1 Replacement Wind Speed Sensor and WC1 Replacement Wind Compass Sensor for Raymarine ST50 and ST60 Wind Instruments. Rev 4.
Micrio WS1 Replacement Wind Speed Sensor and WC1 Replacement Wind Compass Sensor for Raymarine ST50 and ST60 Wind Instruments. Rev 4.1 The Micrio WS1 Wind Speed Sensor and WC1 Compass Sensor are direct
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
COMMON SAILING GLOSSARY OF TERMS
COMMON SAILING GLOSSARY OF TERMS Abeam Aboard Anchor Aft Off to the side of a vessel at right angles to the boat s centerline. On or in the boat A device used to hold a boat to the sea bottom At, near
Drive shaft, servicing
Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,
Weta Class Rules. This introduction provides an informal background and is not part of the Weta class rules.
Introduction The Weta is a trimaran developed by Weta Marine Ltd. Weta hulls, beams, hull appendages, rigs and sails shall only be manufactured by Weta Marine Ltd or their appointed manufacturers. A hull,
STEP I INSERT MAST. IA. Roll out the sail with the zippers facing upwards.
STEP I INSERT MAST IA. Roll out the sail with the zippers facing upwards. IB. Push the mast all the way to the top of the sleeve with one hand on the mast inside the boom cutout and one hand pulling the
Nor thbr id ge Sailing C lub Rescuing Centreboard Dinghies
FOREWORD The following draws heavily on an article written by Don McKenzie of the Northbridge Sailing Club 20 years ago. It has been augmented and updated with the assistance of experienced rescue crew
Kids Woven - Minimum Construction Standards
Kids Woven - Minimum Construction Standards NOTE All construction standards will be followed except when specified otherwise Must use Bon-Ton approved suppliers Vendor must meet all applicable Bon-Ton
RS400 www.ldcracingsailboats.co.uk
RS400 OWNER S MANUAL LDC Racing Sailboats, Trafalgar Close, Chandlers Ford, Eastleigh SO53 4BW, GBR Tel. +44 (0)23 8027 4500 Fax. +44 (0)23 8027 4800 www.ldcracingsailboats.co.uk INTRODUCTION Congratulations
MM 45 Charter Catamaran Subchapter "T" - 49 Passenger
MM 45 Charter Catamaran Subchapter "T" - 49 Passenger Make: MM 45 Charter Catamaran Model: Subchapter "T" - 49 Passenger Length: 45 ft Price: $ 600,000 Year: 2015 Condition: New Location: Portland, United
INSTRUCTION FOR ASSEMBLY. 150x180 v Traditional sauna cabin
INSTRUCTION FOR ASSEMBLY 150x180 v Traditional sauna cabin 1. SAUNA PLAN 1800 LIGHT UNDER THE BENCH VENTILATION OUTLET UPPER BENCH 600 1500 LOWER BENCH 400 700 1656 956 HEATER 366 381 690 815 Light switch
Soch Sails DF65 Rig Kit Manual
Soch Sails DF65 Rig Kit Manual A simple yet useful guide to building a new rig for a DF65 written in a manner that you can understand without needing a degree in rocket science or membership of MENSA.
DIAMOND Retractable Rodding Robot Model SPRAYROD-R
2004-12-21 2 1 (23) DIAMOND Retractable Rodding Robot Model SPRAYROD-R 2004-12-21 2 2 (23) Table of contents 1 TECHNICAL DESCRIPTION...4 1.1 MAIN DETAILS...5 1.2 COMPONENTS DESCRIPTION...5 1.2.1 Pneumatic
PLASTIMO JIB REEFING SYSTEMS S-SERIES 406-S 608-S 810-S
PLASTIMO JIB REEFING SYSTEMS S-SERIES 406-S 608-S 810-S GB ASSEMBLY INSTRUCTIONS FOR S-SERIES 406-S 608-S 810-S I N D E X Technical specifications of 406-S, 608-S, 810-S 3 Description of specific parts
RS600 OWNER S MANUAL. LDC Racing Sailboats, Trafalgar Close, Chandlers Ford, Eastleigh SO53 4BW, GBR Tel. +44 (0)23 8027 4500 Fax. +44 (0)23 8027 4800
RS600 OWNER S MANUAL LDC Racing Sailboats, Trafalgar Close, Chandlers Ford, Eastleigh SO53 4BW, GBR Tel. +44 (0)23 8027 4500 Fax. +44 (0)23 8027 4800 www.rssailing.com INTRODUCTION Congratulations on the
Class Rules Effective 1st April 2013
Class Rules Effective 1 st April 2013 TABLE OF CONTENTS CLASS RULES 1 OBJECTIVES OF THE CLASS RULES 1 2 ADMINISTRATION 1 3 CONSTRUCTION AND MEASUREMENT 3 4 REQUIRED EQUIPMENT WHEN RACING 10 5 CREW 10 6
Auto Sentry-eXP Maintenance
Auto Sentry-eXP Maintenance Maintenance Procedures for Auto Sentry exp Bill Dispenser Credit Card Reader Bill Acceptor Bill Dispenser Maintenance Bill Dispenser Problem / Cause Bill Dispenser Error Codes
How To Secure To A Boat
Mooring Equipment A Conservancy maintained mooring consists of a heavy black iron chain riser, which is attached to a sinker or ground chain. The swivel allows the boat to swing freely at the mooring without
Installation instructions, accessories - Handsfree for cellular phone, system B, entry level
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18
30 minutes in class, 2 hours to make the first time
Asking questions and defining problems Developing and using models Planning and carrying out investigations 30 minutes in class, 2 hours to make the first time 3 12 x 24 x ¾ inch plywood boards 1 x 12
Juice Box Stages 1&2 135&335 Installation Guide 5/10/08
Tools Required: 8mm socket or nut driver Small flat head screwdriver Electrical tape, masking tape, or shrink tube Pep talk: Although the install looks daunting at first, once you get the learning curve
50AI01oe 02/15. Labko GRP cesspools. Instructions for installation, operation and maintenance
02/15 Labko GRP cesspools Instructions for installation, operation and maintenance Reliable solutions Wastewater treatment systems Contents 1 LABKO CESSPOOLS... 3 1.1 GENERAL... 3 1.2 IMPORTANT TO KNOW
PLATU 25 CLASS RULES. The PLATU 25, designed by Bruce Farr, was adopted as a recognised class in November 2005.
PLATU 25 CLASS RULES 2008 The PLATU 25, designed by Bruce Farr, was adopted as a recognised class in November 2005. INDEX PART I ADMINISTRATION Section A General A.1 Language... A.2 Abbreviations... A.3
Printrbot Getting Started Guide. For models: Printrbot Plus (v2) Printrbot LC (v2) Printrbot jr
Printrbot Getting Started Guide For models: Printrbot Plus (v2) Printrbot LC (v2) Printrbot jr Contents 4 Chapter 1: Welcome 4 Overview 4 Support 5 Chapter 2: Your Printrbot has arrived... now what? 5
DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT
-J00 REV. 00-- DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT GENERAL Kit Number -A, 0-, -, 0-, -, - 0, -0 Models These kits fit and later FXST, FXSTB, FXSTC, and and later FXDWG Harley-Davidson model
PARTS CATALOG. Prindle 15 Prindle 16 Prindle 18 Prindle Escape. Prindle 19MX. Prindle 19. Prindle 18-2
PARTS CATALOG 15 16 18 Escape 18-2 19 19MX TABLE OF CONTENTS BASIC CATAMARAN ILLUSTRATION Mainsail Battens Mast Jibsail Hull Assembly.................3 Rear Crossbar Assembly...........3 Front Crossbar
Horizontal Mini Blinds Installation Guide
Horizontal Mini Blinds Installation Guide We make it easy! BTG 468298 EN_ rev0614 For more safety information: 1-866-662-0666 or.www.healthcanada.gc.ca/blindcords Before starting Your new Blinds To Go
LIFE SCIENCE. Hoop House Construction for New Mexico: 12-ft. x 40-ft. Hoop House BRINGING TO YOUR HOME ECONOMICS COLLEGE OF AGRICULTURE AND
Hoop House Construction for New Mexico: 12-ft. x 40-ft. Hoop House COLLEGE OF AGRICULTURE AND HOME ECONOMICS BRINGING SCIENCE TO YOUR LIFE Hoop House Construction for New Mexico: 12-ft. x 40-ft. Hoop House
OWNER S MANUAL Version 2
OWNER S MANUAL Version 2 CONTENTS 1. INTRODUCTION 2. EC CONFORMITY AND IDENTIFICATION 3. SAFETY INFORMATION 3.1 Design Category 3.2 Loading 3.3 Safety Equipment 3.4 Capsize Recovery 3.5 Air Tank 3.6 Man
SOLSTICETM International Leisure Products, Inc. 191 Rodeo Drive Edgewood, NY 11717 Tel (631)254-2155
SOLSTICETM International Leisure Products, Inc. 191 Rodeo Drive Edgewood, NY 11717 Tel (631)254-2155 Introduction We thank you for your purchase of our SOLSTICE SPORTSTER 265 & 266 series boat. Please
INTERNATIONAL TECHNO 293 CLASS RULES
INTERNATIONAL TECHNO 293 CLASS RULES INDEX INTRODUCTION... 3 C.9 Sails...8 PART I ADMINISTRATION Section A General A.1 Language... 4 A.2 Abbreviations... 4 A.3 Authorities and Responsibilities4 A.4 ISAF
White Paper. Recommendations for Installing Flash LEDs on Flex Circuits. By Shereen Lim. Abstract. What is a Flex Circuit?
Recommendations for Installing Flash LEDs on Circuits By Shereen Lim White Paper Abstract For the mobile market some PCB assemblies have been converted to flex circuit assemblies, in part because flex
Arctic Leash Instruction Manual Alaskan Products Company LLC.
Retractable Cord Reel for Engine Block Heaters Arctic Leash Instruction Manual Alaskan Products Company LLC. INSTALLATION INSTRUCTIONS This instruction manual is a reference guide for installing and operating
Tool And Material Checklist
HOW - TO CV JOINTS CV JOINTS Tool And Material Checklist Screwdriver Metal Shears Breaker Bar or Torque Wrench Assorted Wrenches Wire Evaporating Spray Solvent Pusher Tool Vise Snap Ring or Duckbill Pliers
blokarts, sails & masts
blokarts, sails & masts BLO305* Blokart Classic 3.0m kr. 15.062 1.995 BLO405* Blokart Classic 4.0m kr. 15.817 2.095 BLO505* Blokart Classic 5.5m kr. 16.572 2.195 BLO310* Blokart Comp 3.0m kr. 18.686 2.475
Plate carrier, Strap-on DF -13 MANUAL
Plate carrier, Strap-on DF MANUAL THE COMPLETE SYSTEM What is the complete system? The strap on system is developed to be an integral part of the soldier s equipment, working together with all other parts
DRAGON FORCE RESTRICTED CLASS RULES 2014
Dragon Force Restricted Class Rules 2014 2013 Version 1.3 1.0 DRAGON FORCE RESTRICTED CLASS RULES 2014 Version 1.3 Dragon Force Rules Committee 2014 Introduction The Dragon Force project started in 2011
J/70 Tuning Guide. onedesign.com Follow North Sails on... For any question you may have on tuning your J/70 for speed, contact our experts:
Photo Paul Todd/OUTSIDE IMAGES For any question you may have on tuning your J/70 for speed, contact our experts: Tim Healy 401-683-7997 [email protected] Will Welles 401-683-7997 [email protected]
ERECTION INSTRUCTIONS FOR CAMPUS SEATTLE
ERECTION INSTRUCTIONS FOR CAMPUS SEATTLE BEFORE USE PLEASE TAKE TIME TO READ AND UNDERSTAND THE ERECTION INSTRUCTIONS. FAILURE TO ERECT THE TENT IN ACCORDANCE WITH THE INSTRUCTIONS MAY RESULT IN DAMAGE
How to Install Hardwood Flooring Over a Sub Floor
How to Install Hardwood Flooring Over a Sub Floor Installation Preparation Instructions Read the entire instructions before starting your project. 1) INSPECT EACH PLANK (see fig. a) Wood is a natural product
Battcar Installation Manual System B CB and Slider Cars 6mm Clevis Pin
Battcar Installation Manual System B CB and Slider Cars 6mm Clevis Pin CB/Slider Systems Parts List Thank you for puchasing Harken's B Battcar system. Please read manual before assembling system. Intermediate
CARBO RACING FOIL. Unit 0, 1, 2, 3. Installation Manual Intended for specialized personnel or expert users
CARBO RACING FOIL Unit 0, 1, 2, 3 Installation Manual Intended for specialized personnel or expert users 4364 09/14 Preassembly Specifications, parts, tools, feeder height, measuring and cutting foil,
J/24 Tuning Guide San Diego models
San Diego models Thanks very much for purchasing your J/24 sails from North Sails we appreciate your business. The following tuning guide is meant to be a starting point in setting up your boat for your
Wall Mount Installation and Use
Wall Mount Installation and Use 1. Introduction The Wall Mount works the same way for all Touchfire cases - the one or two row magnet strip on the back of the case is magnetically attracted to the Wall
DRAGONFLITE 95 RESTRICTED CLASS RULES 2016
DragonFlite Force 95, Restricted Class Rules 2016 2013 Version 1.1 1.0 DRAGONFLITE 95 RESTRICTED CLASS RULES 2016 Version 1.1 DF Racing Rules Committee 2016 Introduction The DragonFlite 95 (DF95) project
Industrial Guideline nr. 2
Industrial Guideline nr. 2 OFFSHORE CONTAINERS Purpose Provide guidance for the safe use of offshore containers in the Dutch mining industry taking in account Dutch legislation and European standards.
EQUIPMENT SET UP RECURVE BOW
EQUIPMENT SET UP RECURVE BOW Archery Australia Inc Coaching and Standards Committee Proudly Sponsored By EQUIPMENT SET UP RECURVE BOW It is important that equipment to be used must be set up correctly
MGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
HOME GYM. Model. Retain This Manual for Reference OWNER'S MANUAL. www.hyper-extension.com
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice www.hyper-extension.com HOME GYM 50036 Hardware Identifier Assembly Instruction Parts List Warranty
Snap Davits for Sailboat
Snap Davits for Sailboat Objective Cruising Southern California and the Puget Sound on our 2007 Catalina 320 MK II Sailboat requires that we carry an inflatable dinghy. To make the process of carrying
EXTREME 40 CLASS RULES 2012
EXTREME 40 CLASS RULES 2012 EFFECTIVE FROM 1 ST AUGUST 2012 Published 1/8/12 INDEX PART I ADMINISTRATION Section A General A.1 Language... 3 A.2 Abbreviations... 3 A.3 Authorities... 3 A.4 Administration
jbs nfb INSTALLATION INSTRUCTIONS AND OWNERS MANUAL Mechanical Steering for Inboard, Outboard, and Sterndrive Powered Vessels
MEMBER INSTALLATION INSTRUCTIONS AND OWNERS MANUAL Part # IS-SH5094, Rev 3, 04/204 www.seastarsolutions.com SH5294 DUAL SH5094 SINGLE jbs nfb Mechanical Steering for Inboard, Outboard, and Sterndrive Powered
How to Make a Solar Cooker Kristi Jerger s 5th grade class
How to Make a Solar Cooker Kristi Jerger s 5th grade class Dublin, Ohio Public Schools Credits: Marlin Languis, Emeritus Professor, Ohio State University Zep Wallace, Computer Specialist, Dublin Ohio Public
EZ-Steer Assisted Steering System
EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-54 Case IH CVX 1135 CVX 1145 CVX 1155 CVX 1170 CVX 1190 CVX 1195 CVX 135 CVX 145 CVX 155 CVX 175 CVX 195 New Holland TVT
Responsibilities of a Volunteer Leader
Responsibilities of a Volunteer Leader Inspecting tools for safe conditions. Removing unsafe tools from use and immediately notifying site supervisor. Teaching safe tool use to volunteers on your crew.
Basic Spring Motor Roller Shades
Comprehensive Roller Shade Installation Guide Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension
After reading this lesson you will be able to: 12.3 IMPORTANCE OF ROOF 12.4 TYPES OF ROOF IN A HOUSE
86 :: Certificate in Construction Supervision (CIVIL) 12 ROOF 12.1 INTRODUCTION The structure provided to cover the house surface (floor) is known as roof. For different situation and requirement, it is
The load carrier system designed for professionals
The load carrier system designed for professionals THULE PROFESSIONAL The rugged time-saving system Thule Professional is a load carrier system from the world leader in utility transportation. Every aspect
A cascading 16:1 vang for the Coronado 15
cascading : vang for the Coronado Justin Mills, [email protected] pril 0, 00 This guide is written with the assumption that you are replacing an existing (underpowered) vang on your Coronado.
OWNER S MANUAL. LDC Racing Sailboats, Trafalgar Close, Chandlers Ford. Eastleigh SO53 4BW, England Tel. +44 (0)23 8027 4500 Fax. +44 (0)23 8027 4800
OWNER S MANUAL LDC Racing Sailboats, Trafalgar Close, Chandlers Ford. Eastleigh SO53 4BW, England Tel. +44 (0)23 8027 4500 Fax. +44 (0)23 8027 4800 1 CONTENTS 1. INTRODUCTION 2. SPECIFICATIONS AND DRAWINGS
Trillium 40 Axis Spring Tensioner Wire Replacement Instructions
Trillium 40 Axis Spring Tensioner Wire Replacement Instructions 1 Overview The objective is to replace the broken axis spring tensioner wire. This requires the following tasks: 1. Remove the seismometer
Check for deteriorated, shifting or missing tie-down pads. Replace if needed.
C C 0 5 C H A S S I S F R A M E Chassis Frame Overview The Blue Bird Vision s chassis frame consists of two main C-channel rails which run the entire length of the bus, and several different kinds of cross
ROOF CONDENSATION: A COSTLY PROBLEM
ROOF CONDENSATION: A COSTLY PROBLEM CONTENTS 1. What is it? 2. How does it form? 3. What to look for 4. Repair options 5. Owner responsibilities and proactive measures 1. WHAT IS IT? Roof condensation
WARNING! WARNING! ALWAYS WEAR A TMA APPROVED FALL ARREST SYSTEM WHEN USING ANY TREESTAND
WARNING! You must read and understand all of the following instructions before first use. If you do not, it could result in serious injury up to and including death. Any questions please call 309-691-9653.
Assembly and Usage Instructions
Assembly and Usage Instructions A Product 5885 West Van Horn Tavern Road Columbia, MO 65203 www.caldwellshooting.com Instruction #1001667 Limited Warranty Every Caldwell product is warrantied to be free
10 ft x 20 ft / 3 m x 6 m STEEL FRAME CAR CANOPY
10 ft x 20 ft / 3 m x 6 m STEEL FRAME CAR CANOPY Instruction Manual ITM./ART.496840 VIEW ASSEMBLY VIDEO AND INSTRUCTION MANUAL AT www.zhengteusa.com Before assembly, read these instructions carefully.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Application Outboards Faria 5 Gauge Set* Publication No. Description Part Number Honda Code PII53606A White faced, flat lens 06300-ZW5-010ZB 6315410 Issue Date Black faced, flat
Fall Protection and Fall Prevention. San José State University Environmental Health and Safety Facilities Development & Operations
Fall Protection and Fall Prevention San José State University Environmental Health and Safety Facilities Development & Operations Learning Objectives To understand the hazards of falls To understand when
EMPLOYEE FALL PROTECTION
EMPLOYEE FALL PROTECTION You can fall from any height and be seriously injured or killed. In the construction industry, as well as any other industry, when falls from heights happen, they are usually very
Solstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
BUILDING WITH STONE AND EARTH
BUILDING WITH STONE AND EARTH PART 1 Earth is a popular building material all over the world. It can be used by itself, but if there is stone available, then the two can be used together to make very good
A PRODUCT OF NEMAG HOLLAND
USER MANUAL ROPE PEAR SOCKETS SIZE: 1-17 A PRODUCT OF NEMAG HOLLAND 1. INTRODUCTION 1.1 Field of application 1.2 Technical specifications of NEMAG Rope Pear Sockets 1.3 Technical specifications of the
Auto-belay Cable Replacement Process
Auto-belay Cable Replacement Process Version 2.00 WARNING: The air pressure in the auto-belay system is what causes the cable to be retracted when releasing the cable or climbing the wall with the cable
Patient Lifts SAFETY GUIDE
Patient Lifts SAFETY GUIDE Caregiver Safety Tips.... 1 Know Your Lift... 2 Check Patient's Condition.... 3 Select Patient's Sling Size.... 4 Choose Sling and Sling Bar.... 5 Prepare Environment.... 6 Prepare
39HQ Airovision Air Handling Units
39HQ Airovision Air Handling Units Mounting instructions CONTENTS 1 - TRANSPORT AND LIFTING INSTRUCTIONS... 3 1.1 - General... 3 1.2 - Transport and storage... 3 1.3 - Roof edge protection during transport
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech Components 1 Sky Commander Digital Setting Circle Computer 2 Encoders 10,000 step 1 Sky Commander Digital Setting Circle Manual
Oceanscience Cable Chimp II Cableway ROV System User Guide and Warranty
Oceanscience Cable Chimp II Cableway ROV System User Guide and Warranty Page 1 Table of Contents Introduction Page 3 Overview Page 3 Setup and Operation Page 5 Remote Control Page 6 Power Management Page
Have fun, nevertheless!
Nanomum The Nanomum is a small pusher gyro for flying indoors or outdoors in very calm weather. It's got a dc head and is easy to build and easy to fly - I hope. Specs: AUW 70 g / 2.5 oz. Rotor diameter:
HOW TO BUILD A LOU-VEE-AIRCAR
HOW TO BUILD A LOU-VEE-AIRCAR MATERIALS (PER CAR) 1. One sheet of legal-sized paper 2. Three standard paper clips 3. One butterfly paper clip 4. One plastic soda straw 5. Two large index cards 6. Narrow
Installation guide for the SafeLine type anchorage device. Tested in compliance with EN 795: 1996. No.: SE-...
Installation guide for the SafeLine type anchorage device Tested in compliance with EN 795: 1996 No.: SE-... Version: 09.10.2008 SE 67 Subject to technical alterations! Contents 1. General information
ROTOR LOADER OWNER S MANUAL
ROTOR LOADER OWNER S MANUAL ROTOR LOADER OWNER S MANUAL WARNING IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES. Misuse of paintball equipment may cause serious injury or death. QUICK SET-UP GUIDE BATTERY
IMPORTANT SAFETY RULES TO FOLLOW
WARNING FLOOR & CARPET CLEANER Any piece of equipment can be dangerous if not operated properly. YOU are responsible for the safe operation of this equipment. The operator must carefully read and follow
2012-2013 Clamcleat Product Line
0-0 lamcleat Product Line omplementary ranges to satisfy all needs. leats & hocks The lamcleat principle deceptively simple ridged 'V' groove holds ropes firmly, yet is devoid of any moving parts to break
Simple Machines. What are simple machines?
Definitions to know: Simple Machines Work done when an applied force causes an object to move in the direction of the force Energy ability to cause change; can change the speed, direction, shape, or temperature
Installation information. METTLER TOLEDO MultiRange Floor scales / Pit scales
Installation information METTLER TOLEDO MultiRange Floor scales / Pit scales KC300/KCS300 KC600/KCS600 KD600/KD1500 KE1500/KE3000 KES1500/KES3000 KG3000/KG6000 KN1500 Floor scales / Pit scales Contents
IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE USE.
Flip Front2Back Carrier Owners Manual Instructions IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE USE. Read all instructions before assembling and using your carrier. Failure to follow each instruction can result
I BEAM TRACK INSTALLATION
PDQ 0/700 FESTOON SYSTEM INSTALLATION AND MAINTENANCE INSTRUCTIONS INTRODUCTION The PDQ Festoon System was designed to run on one of three sizes of I-beams: S x., S8 x 8. and S x.. System trolleys must
Dell P Series Monitor VESA Mounting Bracket Installation Instructions
Dell P Series Monitor VESA Mounting Bracket Installation Instructions The VESA mounting bracket enables a Wyse cloud client to be mounted to the Dell P Series Monitor and the Dell E24 Monitor. The cloud
RAUFOSS EXPLOSIVE COMPRESSION FITTINGS
INSTRUCTION MANUAL FOR RAUFOSS EXPLOSIVE COMPRESSION FITTINGS Box 7 2831 Raufoss Norway Tlf.: +47 61 15 17 87 Fax: +47 61 15 25 56 25 January 2013, rev 2 Available on www.vpmetall.no Page 1 CONTENTS GENERAL
DRESSING. Fastenings. Managing a tie. Putting on a bra
DRESSING Tips Clothes should be laid out in the same way before dressing, daily. Dress in the same sequence, daily. Dress in front of mirror for visual assistance. Make use of your teeth if necessary.
WINDOW REPAIR MANUAL & REFERENCE GUIDE
WINDOW REPAIR MANUAL & REFERENCE GUIDE TABLE OF CONTENTS DOUBLE HUNG & SINGLE HUNG PARTS 4-5 CASEMENT PARTS 6 SCREEN PARTS 7-8 HOW TO REMOVE TILT-IN SASH 9 HOW TO REMOVE A BALANCE 10 HOW TO INSTALL BALANCE
SAILMAKERS INSTRUCTIONS WEBSITE VERSION
SAILMAKERS INSTRUCTIONS WEBSITE VERSION CONTACT FORESPAR FOR A DRAWING AND VESSEL-SPECIFIC DIMENSIONAL DATA (ITEMS A - K ON PAGE 2) SPECIAL NOTE TO SAILMAKERS: PLEASE READ THESE INSTRUCTIONS CAREFULLY
THE TRIMLINE 10' x 20' CANOPY
THE TRIMLINE 10' x 20' CANOPY Instructions for Assembly Please, assemble the TrimLine at home the first time, not at an event. Before beginning assembly of your TrimLine, please take time to review the
INSTALLATION MANUAL «SD» RANGE
INSTALLATION MANUAL «SD» RANGE The FACNOR model SD is the easiest Reefing System in the world to install. You will see, it is designed for a quick and simple installation. It can be fitted without precise
