LF6 ß = 0,82 LF6 ß = 0,82

Transcription

1 NORM REQUIREMENTS WHITE HOT MELT THERMOPLASTICS Comparative Technical Information SPECIFICATION F-2001 F-2003 F Colour (chromacity coordinates) UNE co-ordinates x, y within the region defined in UNE for the white colour 2. Luminance Factor UNE ß Heat Stability UNE variation in ß Accelerated Ultraviolet Ageing 5. Softening Point (ring and ball method) EN 1871 (UV-B) variation in ß 0.05 UNE SP 95 ºC Variation of ß 0,03 UV1 ß 0,05 PR > 95 ºC 6. Flow Resistance UNE Variation h 5 % variation h 0,05 7. Flash Point UNE T 235 ºC Tª > 235 ºC 8. Alkali Resistance (concrete application) MATERIAL NOT SUITABLE FOR ITS DIRECT APPLICATION OVER CONCRETE PAVEMENTS

2 SPECIFICATION F-2001LT F-2005 F-2005HR F-2009 F-2009HR F-2011 F-2015 F Colour (chromacity coordinates) UNE co-ordinates x, y within the region defined in UNE for the white colour 2. Luminance Factor UNE ß 0.80 ß = 0,81 3. Heat Stability UNE variation in ß 0.03 Variation of ß 0,03 4. Accelerated Ultraviolet Ageing EN 1871 (UV-B) variation in ß 0.05 UV1 ß 0,05 5. Softening Point (ring and ball method) UNE SP 95 ºC PR > 95 ºC 6. Flow Resistance UNE Variation h 5 % variation h 0,05 7. Flash Point UNE T 235 ºC Tª > 235 ºC 8. Alkali Resistance (concrete application) MATERIAL NOT SUITABLE FOR ITS DIRECT APPLICATION OVER CONCRETE PAVEMENTS

3 IDENTIFICATION CHARACTERISTICS SPECIFIC. F-2001 F-2003 F Binder content UNE-EN ± 8% of the 2. Luminance factor UNE ± 0,02 of the ± 8% of the ß = 0,80 0,84 3. Pre-mix content 30 % 30 % 20% 4. Resin type Hydrocarbon Hydrocarbon Hydrocarbon 5. Application Spray application. Extrusion and screed box for profiled road markings. It can also be applied through spray. Spray application. 6. Dosage g/m g/m 2 (depending on dimensions and cadence of the relief marks) g/m 2 7. Application temperature ºC ºC ºC 8. Other characteristics and use recommendations

4 SPECIFIC. F-2001LT F-2005 F-2005HR F-2009 F-2009HR F-2011 F-2015 F Binder content UNE-EN ± 8% of the 2. Luminance factor UNE ± 0,02 of the ± 8% of the ß = 0,80 0,84 3. Pre-mix content 22 % 30 % 45 % 30 % 45 % 25 % 20 % 20% 4. Resin type Colophony Colophony Colophony Colophony Colophony Colophony Colophony Colophony 5. Application Spray application. Extrusion and screed box for profiled road markings. It can also be applied through spray. Extrusion and screed box for profiled road markings. It can also be applied through spray. Spray application. Spray application. Spray application, extrusion or screed box for flat road marking. Extrusion and screed box for profiled road markings. It can also be applied through spray. Spray application. 6. Dosage g/m g/m 2 (depending on dimensions and cadence of the relief marks) g/m 2 (depending on dimensions and cadence of the relief marks) g/m g/m g/m g/m 2 (depending on dimensions and cadence of the relief marks) g/m 2 7. Application temperature ºC ºC ºC ºC ºC ºC ºC ºC 8. Other characteristics and use recommendations Enhanced night visibility for hot climates and tropical regions. Product with CE marking Enhanced night visibility Product with CE marking Enhanced night visibility Declared value for each property is indicated on the product Technical Specification. Values obtained by our quality control laboratory for each product lot are available on the corresponding analysis certificate.

5 TYPE FABRICACIÓN Y APLICACIÓN DE PINTURAS ESPECIALES S.A. DURABILITY CERTIFICATES FOR ROAD MARKING SYSTEMS Norms EN and UNE (B method) USE F ECHOSTAR 20 TRM F-2001LT + 3FH F F F ECHOSTAR 5F F-2005 TRM F-2005HR + 3FH LEVEL P6 / 2 MM I P-NR (permanent / non retrorreflective) P-R dry visibility) Daytime Visibility Q4 ( 160) Night Visibility, Dry R5 ( 300) R5 ( 300) R5 ( 300) R4 ( 200) R5 ( 300) R5 ( 300) II P-RW dry and wet visibility) P-RR dry, wet and rain visibility) Night Visibility, Wet RW4 ( 75) RW3 ( 50) RW4 ( 75) Night Visibility, Rain RR1 ( 25) RR1 ( 25) RR3 ( 50) Skid Resistance S1 ( 45) S1 ( 45) S1 ( 45) --- S1 ( 45) ---

6 TYPE FABRICACIÓN Y APLICACIÓN DE PINTURAS ESPECIALES S.A. USE F ECHOSTAR 5F F-2009 (@ 1800 g/m 2 ) F-2009 F-2009HR F-2015 F-2019 F-2019 (@ 1800 g/m 2 ) LEVEL I P-NR (permanent / non retrorreflective) P-R dry visibility) Daytime Visibility B4 ( 0,50) Q4 ( 160) Q4 ( 160) Night Visibility, Dry R5 ( 300) R2 ( 100) R4 ( 200) R5 ( 300) R5 ( 300) R5 ( 300) R3 ( 150) II P-RW dry and wet visibility) P-RR dry, wet and rain visibility) Night Visibility, Wet RW3 ( 50) RW4 ( 75) RW3 ( 50) RW3 ( 50) RW1 ( 25) Night Visibility, Rain RR2 ( 35) RR2 ( 35) Skid Resistance S1 ( 45) S1 ( 45) S1 ( 45) S1 ( 45) S1 ( 45) S1 ( 45) S1 ( 45)

7 FABRICACIÓN Y APLICACIÓN DE PINTURAS ESPECIALES S.A. USE INSTRUCTIONS SCOPE OF USE Asphalt pavements. Relining upon hot melt thermoplastics, and alkyd and acrylic paints: take special care to use the product only upon road markings worn enough. RETRORREFLECTIVITY Retrorreflective road marking by dropping onto the paint film immediately after applied.. APPLICATION Hot application after melting of the material at the indicated temperature. Lower temperatures than those recommended may decrease the adherence. Road marking machine capable of applying and controlling automatically dosage and homogeneity (in accordance with UNE ). CONDITIONS Dry and clean pavements, whose temperature is not below 5 ºC. Ambient temperature exceeding dew point at least 5 ºC. Wind speed below 25 km/h. In case of relining, make sure of the good adhesion of the preexisting road marking on the pavement. PRESENTATION Ref.: F-2001 / F-2001LT / F-2003 / F-2005 / F-2005HR / F-2009 / F-2009/HR / F-2011 / F-2015 / F-2019 / F-2021 / F kg sacks Pallet with 48 sacks = kg (gross weight kg) Ref.: F-2001/G / F-2001LT/G / F-2003/G / F-2005/G / F-2005HR/G / F-2009/G / F-2009HR/G / F-2011G / F-2015/G / F-2019/G / F-2021/G / F-2121/G Big-bag de 600 kg big bags Pallet with 2 big-bags = kg (gross weight kg) SHIPMENT Packaging properly labelled and marked. LIMITATIONS Not suitable for direct application upon concrete pavements. In this case, apply before an adherent primer (F-5010). After opening to traffic, soiling or blackening of road markings may occur road, the traffic and the weather Use the suitable size gradation and type of, requirements of the road marking. DOSAGE Use the amount of material and required in the contract or specifications sheet. An adequate retrorreflectivity is obtained with a dosage from 500 g/m 2 of. CAUTIONS Do not heat the material above 220 º C (safety temperature). Keep the heated material constantly stirred, and use it within six hours. Do not overheat the material and do not subject it to more than four cycles of heating and cooling. STORAGE Use the material within one year from its manufacturing date. Protect from storage in the open, with extreme change of temperature. Non dangerous goods for transport Customs harmonized system: TARIC code Notes: This technical information does not represent guarantee of the performance of the product once applied. It is the responsibility of the user to confirm the suitability of this information for its particular purpose, as well as to test if the product is appropriate for its own use and process.