Chemical Compatibility Guide For Polyethylene Items
|
|
|
- Belinda Henry
- 9 years ago
- Views:
Transcription
1 SpillTech Sales & Marketing 5440 McGinnis Village Place Suite 102 Alpharetta, GA Phone: Fax: SpillTech Manufacturing Brookley Industrial Complex 1627 O Donoghue Street Mobile, AL Phone: Polyethylene Chemical Compatibility Guide Page 1 of 5 Chemical Compatibility Guide For Polyethylene Items This Chemical Compatibility Guide is offered for informational purposes only and was developed from information sources other than SpillTech. The information from such third party sources is believed to be reliable and accurate; however, Purchaser should make its own determination of compatibility before using any SpillTech product. It is the sole responsibility of the Purchaser to determine whether any product is suitable for Purchaser s actual or intended uses. This listing was prepared to provide guidance to the chemical compatibility molded polyethylene. Polyethylene is susceptible to attack by some chemicals which may cause stress cracking, swelling, oxidation or may permeate the polyethylene. These reactions may reduce the physical properties of polyethylene. When considering a polyethylene product for use in secondary containment applications, it is important to note that most secondary containment products are designed to hold leaked chemicals for only hours, a day, at most a week. These secondary containment units would then be cleaned of any chemical. In these short term applications, a greater variety of chemicals may be used with the polyethylene since the exposure time of the chemical to the polyethylene is limited. NO GUARANTEE, WARRANTY, OR REPRESENTATION IS MADE, INTENDED, OR IMPLIED AS TO THE CORRECTNESS OR SUFFICIENCY OF THE CHEMICAL COMPATABILITY GUIDE OR ANY INFORMATION SUPPLIED HEREIN. THE PRODUCTS DISCUSSED HEREIN ARE SOLD WITHOUT ANY WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED. NO WAIVER, ALTERATION, ADDITION OR MODIFICATION OF THE FOREGOING CONDITIONS SHALL BE VALID UNLESS MADE IN WRITING AND MANUALLY SIGNED BY AN OFFICER OF SPILLTECH. IT IS THE PURCHASER S SOLE RESPONSIBILITY TO CONDUCT TESTING TO ESTABLISH THE SUITABILITY OF ANY PRODUCT FOR PURCHASER S INTENDED USE. LIABILITY OF SPILLTECH FOR ALL CLAIMS, WHETHER ARISING OUT OF A BREACH OF CONTRACT, WARRANTY, NEGLIGENCE, STRICT LIABILITY, OR OTHERWISE, IS LIMITED TO THE PURCHASE PRICE OF THE MATERIAL SUPPLIED. Rating Key: L = Products should be suitable for prolonged or repeated contact with these substances, under the conditions specified. S =These substances may adversely affect the polyethylene. Products may be suitable for intermittent contact; however, some deterioration in properties may occur. The user should perform qualification tests before or during usage of the container. N =These substances aggressively attack polyethylene or have vapor pressures incompatible with closed containers. Do not use polyethylene containers in these applications. Acetaldehyde (40%) L Hydrofluorisilicic Acid (All Conc.) L Acetamide L Hydrogen Bromide (10%) L Acetic Acid (50%) L Hydrogen Peroxide (90%) L Acetic Acid (100%) N Hydrogen Phosphide 100% L Acetic Acid Anhydride S Hydroquinone L Acetic Ether S Hydrogen Sulfide L Acetone L Hypochlorous Acid L Acetylene Tetrabromide S Inks L Acrylic Emulsions S Iodine (Alc. Sol.) Conc. L Acrylonitrile L Iron Salts L Adipic Acid L Iso-Octane S Aliphatic Hydrocarbons (Hexane, Octane, etc) L Isopropyl Acetate L Allyl Alcohol (96%) L Isopropyl Alcohol L Alum (Aqueous Solutions) L Isopropyl Ether N Aluminum Chloride (20%) L Jetfuel S Aluminum Fluoride L Kerosene S
2 Polyethylene Chemical Compatibility Guide Page 2 of 5 Aluminum Hydrogen Solution (10%) L Lactic Acid (All Conc.) L Aluminum Hydroxide L Lanolin L Alums (All Types) L Latex L Ammonia (Anhydrous) L Lead Salts L Ammonia (Aqueous) L Lead Acetate Sat d L Ammonia (100% Dry Gas) L Lime L Ammonium Salts L Linseed Oil L Ammonium Acetate L Lithium Salts L Ammonium Biflouride L Lube Oil L Ammonium Carbonate 50% L Magnesium Salts L Ammonium Chloride L Magnesium Carbonate L Ammonium Hydrogen Fluoride (50%) L Magnesium Hydroxide L Ammonium Hydroxide L Magnesium Nitrate L Ammonium Metaphosphate Sat d L Magnesium Oxide L Ammonium Nitrate (10%) L Magnesium Sulfate L Ammonium Nitrate Sat d L Maleic Acid L Ammonium Persulfate Sat d L Malic Acid (1%) L Ammonium Phosphate L Mercuric Salts L Ammonium Sulfate (1)%) L Mercurous Salts L Ammonium Sulfate Sat d L Mercury L Ammonium Sulfide Sat d L Methanol L Ammonium Thiocyanate Sat d L Methyl Acetate L Amyl Acetate L Methyl Alcohol (100%) L Amyl Alcohol (100%) L Methyl Amine (32%) L L Amyl Chloride N Methyl Bromide N Aniline (100%) S Methyl Chloride N Aniline Hydrochloride S Methylene Chloride N Animal Fats L Methyl Ethyl Ketone S Anti-Freeze L Methyl Isobutyl Ketone S Antimony Salts L Methyl Isopropyl ketone S Antimony Trichloride 90% L Methyl Sulfate L Aqua Regia N Methyl Sulfuric Acid (All Conc.) L Aqueous Salt Solutions (NaCl) L Milk L Aqueous Alkalies (NaOH) L Mineral Oils L Arsenic Acid L Molasses L Arsenic Salts L Monochloroacetic Acid Ethyl Ester L Barium Salts L Monochloroacetic Acid Methyl Ester L Barium Carbonate L Morpholin L Barium Chloride L Mowilith D L Barium Cyanide L Muriatic Acid L Barium Hydroxide L Naptha S Barium Nitrate L Napthalene S Barium Sulfate L Nickel Salts L Barium Sulfide L Nicotine Dilute L Battery Fluid Acid S Nicotinic Acid L Beef Tallow Emulsion, Sulfonated L Nitric Acid <50% L Beer L Nitrobenzene S Benzaldehyde L Nitrotoluene S Benzene L Octyl Cresol L Benzene Sulfonic Acid S Oils and Fats L Benzoic Acid L Oleic Acid (All Conc.) L Benzyl Alcohol L Oleum Conc. N Benzyl Chloroformate L Olive Oil L Bismuth Salts L Orange Extract L
3 Polyethylene Chemical Compatibility Guide Page 3 of 5 Bleach Lye (10%) S Oxalic Acid (All Conc.) L Black Liquor L Palmitic Acid N Borax Cold Sat d L Palm Oil S Boric Acid Dilute L Paraffin Emulsions L Boric Acid Conc. L Paraffin Oil L Bromine Liquid N Perchloric Acid (50%) L Bromine Water N Perchloroethylene N Bromobenzene N Petroleum L Bromoform N Petroleum Ether S Butadiene L Phenol (90%) N Butane L Phenylhydrazine N Butanediol (100%) L Phosphoric Acid All Conc L Butanol L Phosphorous Chlorides S Butyl Acetate L Phosphorous Yellow (100%) L Butyl Alcohol (100%) L Phosphorous Pentoxide L Butylene N Photographic Solutions L Butylene Glycol L Phthalic Acid (All Conc.) L Butylene Liquid N Phthalic Anhydride L Butyl Phenol N Pickling Baths Sulfuric Acid L Butyric Acid L Pickling Baths Hydrochloric Acid L Calcium Carbonate L Picric Acid (1%) L Calcium Chloride L Plating Solutions L Calcium Hydroxide L Potash L Calcium Hypochlorite L Potassium/Aluminum Sulfates (50%) L Calcium Nitrate (50%) L Potassium Bichromate L Calcium Sulfate L Potassium Borate (10%) L Camphor Oil N Potassium Bromide L Carbon Disulfide N Potassium Chlorate L Carbonic Acid (Aq.CO2) L Potassium Chloride L Carbon Monoxide L Potassium Chromate L Carbon Tetrachloride N Potassium Cyanide L Castor Oil Conc. L Potassium Dichromate 40% L Caustic (Aqueous) L Potassium Ferri/ Ferro Cyanide Sat d L Caustic Potash Sol. (50%) L Potassium Fluoride L Caustic Soda Sol. (10%) L Potassium Hydroxide L Chloral Hydrate L Potassium Iodide L Chloroethanol L Potassium Nitrate Sat d L Chloric Acid (10%) L Potassium Perborate Sat d L Chloroacetic Acid L Potassium Perchlorate L Chlorobenzene L Potassium Permanganate L Chloroform N Potassium Persufate Sat d L Chloromethane N Potassium Phosphates L Chlorosulfonic Acid 100% N Potassium Sulfate L Chrome Alum Sat d L Propanol L Chromic Acid (50%) S Propargyl Alcohol (7%) L Cider L Propionic Acid (50%) L Citric Acid (All Conc.) L Propyl Alcohol L Clorox Bleach L Propylene Dichloride (100%) L Coconut Oil Alcohols L Propylene Glycol L Cola Concentrates L Propylene Oxide L Compressed Air Conditioning Oil L Pyridine S Copper Salts L Rayon Coagulation Salts L Copper Cyanide L Rust Inhibitors L Copper Nitrate L Sea Water L
4 Polyethylene Chemical Compatibility Guide Page 4 of 5 Copper Sulfate L Selenic Acid L Corn Oil L Sewage L Cottonseed Oil L Shortening L Cresol (90%) L Silicic Acid L Cresylic Acid L Silicone Oil L Crotonic Aldehyde L Silver Salts L Cuprous Chloride Sat d L Silver Nitrate L Cyclohexane L Soda Solution (All Conc.) L Cyclohexanol L Soda Ash L Cyclohexanone S Sodium Salts L Detergents (General) L Sodium Acetate Sat d L Developer, Photographic L Sodium Acrylates L Dextrin Sat d L Sodium Benzoate L Dextrose Sat d L Sodium Bicarbonate L Dibutyl Ether N Sodium Bisulfate (10%) L Dibutylphthalate S Sodium Bisulfite L Dibutyl Sebacate S Sodium Bromate S Dichloroacetic Acid S Sodium Bromide L Dichloroacetic Acid / Methyl Ester S Sodium Bromide Dilute Sol. L Dichlorobenzene Liquid N Sodium Carbonate L Dichloroethylene N Sodium Chlorate L Diesel Fuel S Sodium Chloride L Diesel Oil S Sodium Chlorite L Diethyl Carbonate L Sodium Chromate L Disodium Phosphate L Sodium Disulfite L Diazo Salts L Sodium Dithionite (10%) L Diethylene Glycol L Sodium Ferricyanide L Diethanolamine S Sodium Ferrocyanide Sat d L Diglycolic Acid (30%) L Sodium Fluoride Sat d L Di-Isobutyl Ketone S Sodium Hydroxide Conc. L Dimethylamine S Sodium Hypochlorite L Dimethyl Formamide S Sodium Iodide L Dinonyl Phthalate N Sodium Nitrate L Dioctyl Phthalate N Sodium Oxalate L Dioxane L Sodium Persulfate L Diphenyl Oxide N Sodium Phosphate L Electrolyte L Sodium Silicate L Emulsions, Photogtraphic L Sodium Sulfate L Ethanol L Sodium Sulfide L Ether N Sodium Sulfite L Ethyl Acetate (100%) S Sodium Sulfonates L Ethyl Alcohol L Sodium Thiosulfate L Ethyl Butyrate S Spindle Oil L Ethyl Chloride N Stannic Salts L Ethyl Ether N Stannous Salts L Ethylene Chloride N Starch Solution Sat d L Ethylene Chlorohydrin L Stearic Acid (All Conc.) L Ethylene Diamine L Succinic Acid L Ethylene Dichloride N Sugar Solutions (Glucose, Lactose, Sucrose, etc) L Ethylene Glycol L Sulfur L Ethylene Oxide N Sulfuric Acid (98%) S Fatty Acids L Sulfuric Acid Fuming N Fatty Alcohol Sulfonate L Sulfurous Acid L Ferric Salts L Sulfuryl Chloride N
5 Polyethylene Chemical Compatibility Guide Page 5 of 5 Ferric Sulfate L Tallow L Ferrous Salts L Tannic Acid L Ferrous Sulfate L Tanning Extracts L Fertilizer Salts L Tartaric Acid Sat d L Fish Solubles L Tetrachloroethane N Fluoboric Acid L Tetrachloroethylene N Fluosilicic Acid (All Conc.) L Tetraethyl Lead L Formaldehyde (40%) L Tetrahydrofuran N Formamide L Tetrahydronaphthalene N Formic Acid (All Conc.) L Thionyl Chloride N Fruit Pulp L Tin Salts L Fuel Oil L Titanium Salts S Furfural (100%) L Toluene S Furfuryl Alcohol N Toluene Sulfonic Acid S Gallic Acid Sat d L Transformer Oil L Gasoline L Tributylphosphate L Gasohol L Trichloroacetic Acid S Gelatine L Trichloroethane N Gin L Trichloroethylene N Gluconic Acid (All Conc.) L Tricresyl Phosphate L Glucose L Triethanolamine L Glycerine L Trioctyl Phosphate N Glycol L Trisodium Phosphate Sat d L Glycol Ethers L Trichloroethylene N Glyocolic Acid (All Conc.) L Turpentine Oil N Grape Sugar Sat d Aq. L Urea L Heptane L Urine L Hexane L Vegetable Oils L Hexanol Tert L Vinegar L Hydrazine Hydrate L Vanilla Extract L Hydrosulfite (10%) L Wax Alcohol N Hydroxylamine Sulfate L Wetting Agents L Hydrazine (35%) L Whisky L Hydrazine Hydrochloride L White Acid (75%) L Hydroiodic Acid (All Conc.) L Wine L Hydrobromic Acid (50%) L Xylene N Hydrocyanic Acid Sat d L Yeast L Hydrochloric Acid (All Conc.) L Zinc Salts L Hydrofluoric Acid (All Conc.) L Zinc Sulfate L
Royal Edge Re-Flex TPO Chemical Resistance Guide
While it is difficult to foresee all chemicals, chemical combinations, and environments to which RPI Royal Edge TPO Roofing Membrane may be subjected, the following information is suggested to help guide
General Chemical Resistance of PET - Products
General Chemical Resistance of PET - Products The below data reflect the information available to the PET producers members of PlasticsEurope. They should not be construed as implying a legal guarantee
HDPE Chemical Resistance Guide
A B Acetaldehyde S O Barium carbonate saturated S S Acetic acid (1-10%) S S Barium carbonate saturated S S Acetic acid (10-60%) S O Barium hydroxide S S Acetic acid (80-100%) S O Barium sulfate saturated
Reference Sheet Chemical Resistance Chart
Reference Sheet Chemical Resistance Chart DISCLAIMER OF WARRANTY AND LIABILITY Although the information set forth herein is presented in good faith and believed to be correct on the date of issuance, Liquid
Chemical Compatibility Guide
Chemical Compatibility Guide Guide Applicable to the Following: PIG Overpack alvage Drums, PIG Wheeled Overpack alvage Drums, PIG pill Kits in Overpack alvage Drums, PIG pill Kits in Wheeled Overpack alvage
CHEMICAL RESISTANCE GUIDE
COMPAATIVE CHEMICAL ESISTANCE Seven Days At 73.4 F CHANGE IN CHANGE IN CHANGE IN CHANGE IN SUFACE CHEMICAL PODUCTS WEIGHT DIMENSION ELONGATION TENSILE *APPEAANCE** % % % STENGTH % Sulfuric Acid HF - 2230
PRODUCT DATA SHEET PDS A115_E. Metric thread M 1.5 pitch CEI EN 60423 CEI EN 50262
reduced cable entry Metric thread M 1.5 pitch CEI EN 60423 CEI EN 50262 Ref. P Fixing A B C L Light Hole min-max Spanner min-max Quantity Grey (mm) (mm) (mm) (mm) (mm) 1900S.M16N M16x1,5 16,5 6-9,5 19
For dead-end terminations. E981DFN 1/2 19 15 E981EFN 3/4 19 15 E981FFN 1 19 18 E981FFN-CAR 1 19 10
Single Gang FS Boxes Type FSE Rigid Nonmetallic Conduit Switch Boxes For dead-end terminations. Type FSS For multiple dead-end circuit terminations or where additional support is required in stub-up applications.
PRODUCT DATA SHEET PDS A17_E
Multi-entry seal plugs Ref. A L Suitable Quantity for Box/Bag Seal (mm) (mm) TGM38 36A3M1623 3 8 5.000/100 TGM48 36A3M1624 + 36A3M2034 + 36A3M2554 4 8 5.000/100 TGM58 36A3M2025 5 8 5.000/100 TGM513 36A3M2545
Chemical Resistance Chart
Acetaldehyde - Alcohols (Propyl) Chemical Resistance Data These recommendations are based upon information from material suppliers and careful examination of available published information and are believed
TECHNICAL REPORT HOLLOW POLYCARBONATE
TECHNICAL REPORT HOLLOW POLYCARBONATE A Brief Introduction Polycarbonate is a very well-known engineering thermoplastic, as clear as glass and as resistant as steel, it is a carbon derivative that gathers
CHEMICAL RESISTANCE Sikafloor PurCem Products
Version: March 2001 Page 1 of 9 CHEMICAL RESISTANCE Sikafloor PurCem Products Acetaldehyde - D Acetic Acid 5% A Acetic Acid 10% A Acetic Acid (60 o C) 10% E Acetic Acid 30% A Acetic Acid (60 o C) 30% E
Shutting Off Power to EZTouch Panel
Shutting Off Power to EZTouch Panel Removing power from the EZTouch Panel does not normally cause a loss of the user program that is stored in the panel unless the battery voltage is low or the battery
Guidance Note: Chemical Storage
Department of Environmental Health and Safety Guidance Note: Chemical Storage The proper segregation and storage of chemicals is important in the laboratory because the accidental mixing of incompatible
INCOMPATIBILITY OF COMMON LABORATORY CHEMICALS
INCOMPATIBILITY OF COMMON LABORATORY CHEMICALS When certain hazardous chemicals are stored or mixed together, violent reactions may occur because the chemicals are unsuitable for mixing, or are incompatible.
ABSORBANTS SPC SORBENTS & SPILL CONTAINMENT. [email protected] www.tfsi1.com. Toll Free: (800) 331-3118 Fax: (248) 377-3172
SPC SORBENTS & SPILL CONTAINMENT 358 www.tfsi1.com APPLICATION GUIDE Listing of common industrial fluids and the sorbents to use Oil Only Polypropylene include: Universal & Chemical Polypropylene include:
Technical Brief. Thermowell Materials Service Guide K EY C ONSIDERATIONS: Common Materials
Technical Brief K EY C ONSIDERATIONS: Operating Temperature Operating Environment Velocity & Pressure thermowell material is usually chosen based on the corrosion conditions the well will face. Thermowell
Chemical resistance properties
Chemical resistance properties Chemical resistance chart of RTS conveyor belts PVC 2 18 POLYOLEFIN 18 30 POLYURETHANE 18 30 URETHANE IMPREGNATED 18 30 The data are based on laboratory tests and practical
Thermoplastic Polyurethane Elastomers (TPU)
Thermoplastic Polyurethane Elastomers (TPU) Elastollan Chemical Resistance Acids Solvents Alkalis Alcohols Grease, Oils Water Technical Information Introduction The resistance of plastic materials against
CHEMICAL RESISTANCE GUIDE
Acetaldehyde Acetamide Acetic acid (50% concentration) Acetone Acetonitrile Acetophenone Acetyl chloride Acrylamide (same as 2-propenamide) Acrylic acid Aircraft stripper Aluminum nitrate (nonhydrous)
Technical Reference Bulletin Elastomer Compatibility Chart
ASTM D-2000 Classification Trade Names 1-Compatible 2-Minor Incompatibility 3-Severe Incompatibility 4-Not Recommended 0-Insufficient Data To Determine Compatibility Chemical Acetone Acetylene Aluminum
Chemical resistance table
Chemical resistance table The chemical resistance table serves as a guide resistance to media of all asbestos-free s. All information is provided in accordance with the current state of knowledge and subject
3M Scotchkote Fusion-Bonded Epoxy Coating 134
3M Scotchkote Fusion-Bonded Epoxy Coating 134 Data Sheet and Application Guide February 2016 Handling and Safety Precautions: Read all Health Hazard, Precautionary and First Aid, Material Safety Data Sheet,
Liquid Flow Conversions
Liquid Flow Conversions This bulletin provides valuable information for converting liquid flows from water to other liquids. This is extremely useful because many valves are tested and catalogued in water
How to Utilize this Chemical Resistance Guide
How to Utilize this Chemical Resistance Guide Three categories of data are provided for each product and corresponding chemical: 1) breakthrough time; 2) rate, and 3) egradation resistance rating. Color
Chemical Resistance Information Guide. KLEENGUARD* Brand Apparel
Chemical Resistance Information Guide KLEENGUARD* Brand Apparel Chemical Resistance Information Guide KLEENGUARD* Brand Apparel How to Use This Guide The chemical resistance test data is organized by chemical
List of Analytical Reagents(AR)
SAP Code 20011LL200 20011LM500 20026LM500 20042S5K25 20063S5K25 20065SR500 20070LC250 20080SG500 20080S5K50 20080SR500 20092SG100 20094SG100 20095SG500 20095S5K50 20095SR500 20118SG500 20120SG500 20120SR500
Proper chemical storage is required to minimize the hazards associated leaks, spills, and accidental mixing of incompatible chemicals.
CHEMICAL STORAGE Proper chemical storage is required to minimize the hazards associated leaks, spills, and accidental mixing of incompatible chemicals. General Storage Guidelines Observe the following
Chemical Resistance of Polypropylene and Polyethylene
Chemical Resistance of Polypropylene and Polyethylene Generally speaking, the chemical resistance of polypropylene and polyethylene is considered superior to that of metals. They are unaffected by most
LIMITED WARRANTY Blygold PoluAl
Limited Warranty for the Coating LIMITED WARRANTY The heat transfer coils of this unit have been coated with Coating (the Coating ). A unit s coil is defined herein as the heat transfer area up to and
Hazardous Chemical Reactions in Art
Hazardous Chemical Reactions in Art By Michael McCann, PhD, CIH Many art materials are inherently hazardous, including toxic solvents and many metals, corrosive and alkalis, flammable solvents and combustible
Draeger-Tubes and accuro Pump
Draeger-Tubes and accuro Pump Trusted Technology that s ahead of its time Accurate Easy to read Flexible Fast Specific Easy to use Maintenance free Multi-Gas Detector accuro pump One handed operation What
JACKSON SAFETY* G80 Nitrile Chemical Resistant Gloves. Chemical Resistance Guide
JACKSON SAFETY* G80 Nitrile Chemical Resistant Gloves Chemical Resistance Guide This guide presents the results of ASTM F739 standard permeation testing and degradation ratings for the JACKSON SAFETY *
CHEMICAL RESISTANCE AND CHEMICAL APPLICATIONS FOR CPVC PIPE AND FITTINGS. By Michelle Knight
HEMIAL RESISTANE AND HEMIAL APPLIATIONS FOR PV PIPE AND FITTINGS By Michelle Knight hlorinated polyvinyl chloride (PV) has become an important engineering thermoplastic due to its relatively low cost,
Art.Nr. Product group English Pack CasNr CL00.0113.5000 General reagent Acetic acid 80% p. 5 l 64-19-7 CL00.0113.9010 General reagent Acetic acid 80%
Art.Nr. Product group English Pack CasNr CL00.0113.5000 General reagent Acetic acid 80% p. 5 l 64-19-7 CL00.0113.9010 General reagent Acetic acid 80% p. 10 l 64-19-7 CL00.0169.1000 General reagent Acetic
Temple College Compliance with the Environmental Protection Agency Requirements
Temple College Compliance with the Environmental Protection Agency Requirements Background: Temple College is subject to the Federal EPA regulations and procedures in regard to chemical usage, safety and
Chemical Compatibility Chart
Chemical Compatibility Chart 1 Inorganic Acids 1 2 Organic acids X 2 3 Caustics X X 3 4 Amines & Alkanolamines X X 4 5 Halogenated Compounds X X X 5 6 Alcohols, Glycols & Glycol Ethers X 6 7 Aldehydes
Ürün Kodu Açıklaması Amb
Ürün Kodu Açıklaması Amb 15A656.1611 Acetaldehyde 99 % PS 1000 ml 361008.1612 Acetic Acid glacial ( HPLC) PAI 2,5L 131008.1212 Acetic Acid glacial (RFE, USP, BP, Ph. Eur.) PA-ACS-ISO 2,5L 131008.0716 Acetic
Hazard Warning Signage Guidelines
Fire Department 401 Oak Street, #402 Roseville, California 95678-2649 Hazard Warning Signage Guidelines Where hazardous materials are stored in quantities that require a permit pursuant to CFC Table 105.6.20,
Guidance on Safe Storage of Chemicals in Laboratories
Safety Office Reviewed: 17 July 2012 Reviewed: DD Month Year Guidance on Safe Storage of Chemicals in Laboratories The purpose of this document is to explain the principles of safe chemical storage in
7th. Chemical Resistance Guide. Permeation & Degradation Data EDITION
7th EDITION Chemical Resistance Guide Permeation & Data Introduction to the 7th Edition When reviewing the following recommendations, remember that tests are conducted under laboratory conditions, and
Optical Sensors. Rays of hope in the level measurement
Optical s Rays of hope in the level measurement About us j a c o b - t h e s p e c i a l i s t f o r c a b l e g l a n d s a n d m e a s u r i n g t e c h n o l o g y The success story begins in 9. Wilhelm
KRITIFLEX BLACK 6070 (HDPE)
KRITIFLEX BLACK 6070 () Chemical Resistance Tables The following symbols are used in this table: + Specimen is resistant / Specimen has limited resistance only Specimen is not resistant D Discoloration
Safe Storage of Chemicals
Safe Storage of Chemicals Proper storage of chemicals within a laboratory is a difficult and continuing problem. Some experts have stated that the majority of laboratory accidents are related to improper
Going to Great Lengths with. Polyurethane Tubing
Going to Great Lengths with Tubing SOLUTIONS GLOBAL PRODUCTS GLOBAL Tubing Series TIUB & TU SMC Offers a Rainbow of Tubing Types, Colors, Sizes and Lengths has 8 Quick Ship colors, equalling 336 part numbers,
Chemical Resistance Guide
Caveat Note: This chart is for guidance only and is based upon data which has been generated by a laboratory test representing complete immersion of the test sample. In such tests it is not possible to
Decomposition. Composition
Decomposition 1. Solid ammonium carbonate is heated. 2. Solid calcium carbonate is heated. 3. Solid calcium sulfite is heated in a vacuum. Composition 1. Barium oxide is added to distilled water. 2. Phosphorus
DESCRIPTION ASTM 1418 ISO/DIN 1629 Page. SBR Styrene Butadiene Rubber SBR SBR 6. NR Natural Rubber NR NR 6
CALVOSEALING Plancha Rubber Sheet de caucho Elastomer: CALVOSEALING offers a wide range of rubbers for use in general industry. Our company is able to offer 10 types of elastomers where each offers its
STAINLESS STEEL VOLUTE PUMPS
STAINLESS STEEL VOLUTE PUMPS FEATURES APPLICATIONS Pump portion contacting liquid is made of high Industrial use grade 316 stainless steel Chemical solutions BPO (back pull out) system allows all rotating
HOMEWORK 4A. Definitions. Oxidation-Reduction Reactions. Questions
HOMEWORK 4A Oxidation-Reduction Reactions 1. Indicate whether a reaction will occur or not in each of following. Wtiring a balcnced equation is not necessary. (a) Magnesium metal is added to hydrochloric
Waste Management Log Book
Waste Management Log Book Web address: www.ehs.psu.edu Designated Accumulation Area: Building & Room Number Location in Room Supervisor: E-mail Individual Assigned to Oversight: E-mail Form 1 Chemical
Fluid & Gas Properties
Fluid & Gas Properties FLUID DENSITY Density is the ratio of mass to volume. In English, units density is expressed in pounds mass/cubic foot (lbm/ft 3 ). The symbol for density is ρ. Density is usually
FIRE HAZARD PROPERTIES. Acetaldehyde IA -38 (-39) 347 (175) 4.0 60 0.8 1.5 70 (21) Yes 1 2 4 2 CH 3
Acetaldehyde IA -38 (-3947 (17) 4.0 60 0.8 1. 70 (21) Yes 1 2 4 2 CHO (Acetic Aldehyde) (Ethanal) 7-07-0 Note: Polymerizes. See NFPA 49 contained in Fire Protection Guide to Hazardous Materials. Acetone
SCH 4C1 Unit 2 Problem Set Questions taken from Frank Mustoe et all, "Chemistry 11", McGraw-Hill Ryerson, 2001
SCH 4C1 Unit 2 Problem Set Questions taken from Frank Mustoe et all, "Chemistry 11", McGraw-Hill Ryerson, 2001 1. A small pin contains 0.0178 mol of iron. How many atoms of iron are in the pin? 2. A sample
21/06/04 CHEMFREE 2000 LABORATORY FUME CUPBOARDS. s.r.l.
21/06/04 CERTIFIED LABORATORY FUME CUPBOARDS s.r.l. FUME CUPBOARDS CHEMFREE FOREWORD Faster have designed and manufactured fume cupboards using the latest molecular filtration technology. This provides
107-13-1 Acrylonitrile 1 53-96-3 2-Acetylaminofluorene 1 92-67-1 4-Aminodiphenyl 1 7440-38-2 Arsenic 1
A hard copy of this document may not be the document currently in effect. The current version For concentrations less than 1 % (Wt.), the banned and restricted material requirements do not apply, except
The industry leading cargo tank coating for chemical and product tankers.
The industry leading cargo tank coating for chemical and product tankers. from Advanced Polymer Coatings, is the premier cargo tank coating system available for chemical and product carriers, and the only
Naming Ionic Compounds
Naming Ionic Compounds I. Naming Ions A. Cations (+ions) 1. Element name followed by "ion" (when in Group IA, IIA, Al 3+, Ga 3+, Zn 2+, Cd 2+, Ag +, Ni 2+ ). Na + sodium ion, K + potassium ion, Al 3+ aluminum
CHEMICAL COMPATIBILITY CHART. Metallic Materials Used in Bal Seal Products
COMPATIBILITY CHART Metallic Materials Used in Bal Seal Products Technical Report TR-60C (Rev. Ø; 5-28-99) (100-61-3) (100-61-4) (100-27) (100-27-1) (100-27-2) (DE-72 spec.) 19650 Pauling Foothill Ranch,
AP Chemistry Reaction Questions
AP Chemistry Reaction Questions Directions: Give the formulas to show the reactants and the products for the following chemical reactions. Each of the reactions occurs in aqueous solution unless otherwise
3.2 The Department of Environmental Health and Safety is responsible for;
1 Introduction The have been developed in order to minimize the risk of accidental chemical reactions and exposure resulting from the improper storage of hazardous chemicals. The chemical storage procedures
Hazardous Waste Containers. Hazardous Waste Disposal. Examples of HW Containers. Typical Wastes in Chemistry
Hazardous Waste Initial Training Brian Smith, Hazardous Waste Coordinator Environmental Health and Safety Michigan State University THE Absolute Three Things you need to stay out of trouble: Words Hazardous
C A R E U ID. plastic
C A R E G U ID plastic x Blindtext Table of content 1 2 3 3.1 3.2 3.3 3.4 4 4.1 4.2 4.3 4.4 5 5.1 5.2 6 7 Types of plastic................................... 2 Polypropylene (PP).................................
Calculating Molar Mass of a Compound
Instructions for Conversion Problems For every conversion problem Write the number in the problem down with unit and a multiplication sign Decide which conversion factor you should use, Avagadro s or molar
Air Monitoring Guide 3500/3510, 3520/3530, 3550/3551
Air Monitoring Guide 3500/3510, 3520/3530, 3550/3551 1 Instructions for Use Important! You must read all instructions completely before proceeding with any monitoring. General Product Description The 3M
Technical Bulletin. Colors and Sizes: Product Composition. Product Description. Typical ChemArmor HPL Product Types
Technical Bulletin Nevamar ChemArmor High Pressure Laminate (HPL) has been tested and proven to have superior chemical resistance and significantly higher NEMA wear value than competitive laminates. It
All cast acrylic products in PMMA technical properties
All cast acrylic products in PMMA technical properties Index Preface 1 Technical properties 1.1 Mechanical properties 1.2 Thermic and electric properties 1.3 Chemical properties 1.4 Optical qualities 1.5
Naming Compounds Handout Key
Naming Compounds Handout Key p. 2 Name each of the following monatomic cations: Li + = lithium ion Ag + = silver ion Cd +2 = cadmium ion Cu +2 = copper (II) ion Al +3 = aluminum ion Mg +2 = magnesium ion
Flexmaster Joints Conveying Products
Flexmaster Joints Conveying Products Features Flexmaster Joints in Standard and Self-restrained Configurations Standard Features 1. Gasket provides compression seal when tightened against tube or pipe.
ABB Multiwave TM process photometers. ABB Analytical - PUV3402, PIR3502 and PFO3372 process photometers Applications, technology and data
ABB Multiwave TM process photometers ABB Analytical - PUV3402, PIR3502 and PFO3372 process photometers Applications, technology and data Process photometers PUV3402 and PIR3502 Principle of operation The
Naming Compounds. There are three steps involved in naming ionic compounds- naming the cation, naming the anion, and naming the entire compound.
Naming Compounds Naming compounds is an important part of chemistry. Most compounds fall in to one of three categories ionic compounds, molecular compounds, or acids. Part One: Naming Ionic Compounds Identifying
"Quick user guide" for disposal of chemical residues into the waste water system
Sida 1 av 6 "Quick user guide" for disposal of chemical residues into the water system It is never desirable for chemicals to be poured into the water system, but in some cases it is more beneficial for
Laboratory Safety Manual
Chapter 1 Introduction Laboratory Safety Manual Section 6 Fire Safety INTRODUCTION PURPOSE Both flammable and combustible materials are commonplace in most Duke Laboratories. For this reason, all laboratory
Properties and Uses. Physical properties :
Properties and Uses Physical properties : Commercial carbon disulfide often possesses a strong disagreeable and fetid odor due to the presence of very small amounts of strong smelling organic sulfur compounds.
Our business. Great Chemistry. Our model of success OUR MODEL OF SUCCESS
Great Chemistry Our business OUR MODEL OF SUCCESS Shrieve Chemical Company was founded in 1978 supplying commodity chemicals within the USA, providing the foundation for the business to grow and diversify.
Balston Liquid Filters
Balston Vacuum Pump Exhaust and Inlet Filters Gas and Liquid Sample Filtration Process Filtration Specialized Chemical or Solvent Filtration Balston Liquid Filters Filtration to 0.22 micron with exceptional
Oxidizer(s) Management and Use Guidelines
Facilities and Campus Services EHS/RMS 3101 Science Circle CPISB Room 102B Anchorage, AK 99508 Oxidizer(s) Management and Use Guidelines This document provides information concerning the handling, storage,
DURA SLAB MOULDED TECHNICAL SPECIFICATIONS JANUARY 2014
DURA SLAB MOULDED TECHNICAL SPECIFICATIONS JANUARY 2014 Definition Glass-reinforced plastic (GRP) is a composite material made of a thermosetting plastic resin reinforced by fine fibres of glass along
Nomenclature of Ionic Compounds
Nomenclature of Ionic Compounds Ionic compounds are composed of ions. An ion is an atom or molecule with an electrical charge. Monatomic ions are formed from single atoms that have gained or lost electrons.
Chemicals. Hazardous. Safe Storage of. General Assistance. Emergency Phone Numbers. Department Contacts. Office of Environment, Health & Safety
General Assistance Environment, Health & Safety business hours (51) 6-7 Emergency Phone Numbers Life-threatening Emergencies land line 911 cell phone (51) 6- Hazardous Material Spills business hours (51)
Corrosion Resistant Resins for Chemical Containment and Piping. Range and Specification
Corrosion Resistant Resins for Chemical Containment and Piping Range and Specification Chemical Containment Scott Bader offers an outstanding range of corrosion resistant, chemical grade high performance
MITSUBISHI ELECTRIC E1032. Installation manual. English MA00816 2006-04
MITSUBISHI ELECTRIC MA00816 2006-04 E1032 Installation manual English Foreword Installation manual for the E1000 series operator terminals Foreword The E1000 operator terminal is developed to satisfy the
Dosing Pumps BL1.5 - BL3 - BL5 BL7 - BL10 BL15 - BL20 BL7913 - BL7914
Instruction manual Dosing Pumps BL1.5 - BL3 - BL5 BL7 - BL BL15 - BL20 BL7913 - BL7914 These pumps ar in compliance with the CE directives http://www.hannacan.com Dear Customer, Thank you for choosing
FLAMMABLE AND COMBUSTIBLE LIQUIDS
CITY OF BLAINE SAFETY SERVICES 10801 Town Square Drive, Blaine MN 55449 Business Phone 763-785-6187 Fax 763-717-2634 FLAMMABLE AND COMBUSTIBLE LIQUIDS Storage, use, dispensing, mixing and handling of flammable
U.S. Environmental Protection Agency Office of Pesticide Programs List of Inert Pesticide Ingredients List 4A - Minimal Risk Inert Ingredients - By
U.S. Environmental Protection Agency Office of Pesticide Programs List of Inert Pesticide Ingredients List - Minimal Risk Inert Ingredients - By CAS Number Updated August 2004 Inert Ingredients Ordered
Thermo Fisher Scientific. 8x50 sealed. Instruction Manual. 50121058-3 October 2009
Thermo Fisher Scientific 8x50 sealed Instruction Manual 50121058-3 October 2009 2009 Thermo Fisher Scientific Inc. All rights reserved. AutoLock TM is either a registered trademark or a trademark of Thermo
Unit 9 Stoichiometry Notes (The Mole Continues)
Unit 9 Stoichiometry Notes (The Mole Continues) is a big word for a process that chemist s use to calculate amounts in reactions. It makes use of the coefficient ratio set up by balanced reaction equations
Safe Method of Use 7 HSNO Class 3.1 - Flammable Liquids
Safe Method of Use 7 HSNO Class 3.1 - Flammable Liquids A. Classification HSNO Class 3.1 flammable liquids are categorised according to their flashpoints: HSNO Category 3.1A Flammable Liquids with a flashpoint
Repair Sticks. durable versatile high strength. New. Repair Sticks Concrete and Stainless Steel
Repair Sticks durable versatile high strength New Repair Sticks Concrete and Stainless Repair Sticks, Stainless, Copper and Plastic WEICON Repair Sticks The uncomplicated solution for all repair and maintenance
DuPont Permeation Guide
DuPont Guide Tychem Tyvek INTRODUCTION - Chemical What is permeation? is the process by which a potentially hazardous chemical moves through a material on a molecular level. can be represented by the
HAZARDOUS WASTE MANUAL For Faculty, Staff, and Students
Click Here to go to the Table of Contents Department of Chemical Engineering Michigan Technological University Houghton, MI HAZARDOUS WASTE MANUAL For Faculty, Staff, and Students Chemical Hygiene Officer:
DURA SLAB PULTRUDED INDUSTRIAL SECTOR TECHNICAL MANUAL
DURA SLAB PULTRUDED INDUSTRIAL SECTOR TECHNICAL MANUAL For Use In: Substations, Water Treatment Plants, Road/River Bridges, Off Shore Platforms, Industrial Plants, Schools, Hospitals, Warehouses, Factories,
Pipette Tips PACKARD BIOSCIENCE MultiPROBE II COMPATIBLE
User Guide for Reversed-Phase Pipette Tips PACKARD BIOSCIENCE MultiPROBE II COMPATIBLE Notice The information in this document is subject to change without notice and should not be construed as a commitment
Ingredients Checklist
Ingrients Checklist This list was develop to assist custodians in identifying the hazards of ingrients in common cleaning and maintenance products. Although all cleaning chemicals ne to be us with caution,
