Electrical Service Guidelines

Transcription

1 Electrical Service Guidelines Middle Tennessee Electric Membership Corporation Revised: May 23, 2013

2 MTEMC's Electrical Guidelines TABLE OF CONTENTS Right-of-Way Clearance Guide 3 MTEMC Requirements 4 General Metering Requirements 5 Metering Room Specifications 6 ESG-400: 400 Amp Residential Metering 7 LBL-MDMB: Labeling for Multi-Metered Installations 8 ESG-1: Overhead Residential Service 9 ESG-2: Underground Residential Service 10 ESG-3: Underground Residential Service, Pad-Mount Transformer 11 ESG-4: Additional Meter on House 12 ESG-5: Member Pole Service, Standard Underground 13 FSMC-2: Free Standing Meter Center 14 ESG-6: Overhead Temporary Service 15 ESG-7: Underground Temporary Service 16 COM-6: Non Residential Metering with Multiple Customers and Service Laterals from a Single Transformer 17 ESG-8: Security Lighting 18 1S: Secondary Ditch Detail 19 2S: Secondary Ditch Detail 20 CTE-1: Current Transformer Enclosure Specifications 21 ESG-9: Double Throw Switch Configuration of MTEMC Service and Standby Generator 22 ESG-10: Generlink Meter Collar 23 MTEMC Offices Listed 24

3 Right-of-Way Clearance Guide

4 MTEMC Requirements Installation In addition to the National Electrical Code, National Electrical Safety Code, and state and local building codes, MTEMC has installation requirements which must be followed. Please check with an MTEMC engineer or representative before locating the meter base or if you have questions about requirements or specifications. General Specifications A. Overhead Services: 1. Where a MTEMC engineering representative specifies an eyebolt for service attachment, install the eyebolt at a point lower than the weatherhead and no more than 18 horizontally from the weatherhead. 2. Where a MTEMC engineering representative specifies a service mast for service attachments, install 2 1/2 inch rigid metal or IMC conduit fastened with a minimum of 2 mast clamps bolted through the wall on all residential services. 3. All services must comply with Codes requirements for clearance. A minimum 18 ft. clearance is required on all non-residential services. In no case shall a point of attachment be less than 12 ft. or more than 30 ft. above final grade. 4. See ESG-1 for additional specification details. B. Underground Services: See ESG-2 or ESG-3 for specification details. See drawings 1S and 2S for the secondary ditch details. C. Manufactured and Modular Home Services: 1. A red HUD label identifies manufactured or mobile homes. Meters may not be installed on manufactured or mobile homes. See ESG-4 or ESG-5 for specification details. 2. Modular homes are identified by a green State of Tennessee label. Services for modular homes may be identical to overhead or underground residential services. See ESG-1, ESG-2, or ESG-3 for specification details. D. Temporary Services: 1. Overhead - Temporary service pole must be within 125 ft. of MTEMC pole. See ESG-6 for specification details 2. Underground - Temporary service pole must be located behind right corner of pad mount transformer or underground secondary box. See ESG-7 for specification details. E. Meter on MTEMC s Pole: MTEMC no longer allows meter installations on MTEMC poles. When a MTEMC pole is changed out, any meters on MTEMC s poles shall be removed if possible. Meters on poles for communication companies may be transferred to new poles as necessary. GENERAL SERVICE CONDUCTOR Service conductors installed near other utility lines, structures, or obstructions require: A. Conductors run parallel to water or gas lines must have a minimum 3 ft. separation. B. Telephone and TV cable may run in the same ditch with a minimum 36 in. horizontal separation between service conductor and cable; or 12 in. vertical separation AND 18 in. horizontal separation. C. All foreign utility perpendicular crossings must have 12 in. minimum separation from MTEMC ducts.

5 GENERAL METERING REQUIREMENTS Non Residential- anything other than a single family dwelling 1. All meter sockets used in MTEMC s service area must be one of the MTEMC approved meter sockets (bases). All sockets and hubs shall be furnished and installed by the member. 2. All meter sockets must be mounted between 4 and 6 feet above final grade. 3. All meter sockets shall be mounted outdoors in a location that is easily accessible for MTEMC personnel. Any variation must be approved in writing by a MTEMC engineering representative. 4. The maximum allowable service wire to connect to MTEMC padmount transformer is 750MCM. The maximum allowable service wire to connect in UG pull box is 500 MCM. For single phase services of 800 amps or less, MTEMC will pull the service wire from the transformer/pull box to the metering point. 5. For multiple services feeding from the same transformer a non-fused safety switch with provisions for an MTEMC padlock shall be installed on the source side each 277/480V self contained (400 Amps and smaller) meter and each instrument metering installation (larger than 400 Amps). 120/208V and 120/240V self contained (400 Amps and smaller) metering shall require a disconnect adjacent to the meter on the exterior of the building. 6. If more than one metering installation is fed from the same transformer, a disconnect shall be installed on the source side of all troughs and ganged metering installations. 7. If a service conductor feeds several meters (gang meter socket, metering trough, etc.), each meter and disconnect shall be labeled with identification numbers (address). These numbers shall be on a stamped or engraved brass or stainless steel label and attached with 2 or more rivets. They should be in a readily visible location on both the meter and disconnect. Labels shall be furnished and installed by the customer. Residential- single family dwelling 1. All meter sockets used in MTEMC s service area must be one of the MTEMC approved meter sockets (bases). All sockets and hubs shall be furnished and installed by the member. 2. All meter sockets must be mounted between 4 and 6 feet above final grade. 3. All meter sockets shall be mounted outdoors in a location that is easily accessible for MTEMC personnel. Any variation must be approved in writing by a MTEMC engineering representative. 4. The maximum allowable service wire to connect to MTEMC padmount transformer is 750MCM. The maximum allowable service wire to connect in UG pull box is 500 MCM. For single phase services of 800 amps or less, MTEMC will pull the service wire from the transformer/pull box to the metering point. 5. Meter base will not be located on or under porches, decks or carports. The meter base shall be located as close to MTEMC s transformer/pull box as possible. If the distribution panel is not located in immediate vicinity of meter, a weatherproof disconnect may be required; refer to National Electric Code. 6. A grounding electrode conductor (ground wire) of a minimum of No. 4 copper or larger shall be run unspliced from a lug in the meter base to a driven grounding electrode (ground rod). An 8 ft. driven grounding electrode (ground rod) bonded to grounding electrode conductor (ground wire) with clamp suitable for direct soil burial will be installed below final grade.

6 METERING ROOMS NO ELECTRICAL METER ROOM WILL BE ALLOWED WITHOUT PRIOR MTEMC APPROVAL. City or County approval of meter room locations is not sufficient and will not be considered if a meter room is installed without prior MTEMC consultation. A drawing showing the physical arrangement of all meters must be provided to MTEMC prior to obtaining approval. If physical space available requires that meter bases be installed in a vertical arrangement, the highest meter shall be not more than seven (7) feet above the floor to the center of the glass cover, and the lowest meter shall not be less than three (3) feet from the floor to the center of the glass cover. When indoor meter locations are necessary and approved by MTEMC, the meters shall be located where they will be readily accessible at ALL times for emergencies, meter reading, testing and other maintenance purposes. All meter locations shall meet all NEC requirements regarding but not limited to access, egress and clear space around the meter. There shall be a minimum of three and one half (3.5) feet working space between the front of the meter socket and any walls or other obstructions. In the event that the meter room is located inside of the building, all secondary conductors under the building shall be encased in RED concrete and be installed 12 inches below all indoor facilities (water, gas, sewer). Raceway under the building shall be responsibility of owner to maintain or repair in the event of failure, therefore installing a spare conduit(s) at time of construction may be advantageous. The concrete encasement shall extend a minimum of three (3) feet from the edge of the building foundation. If the meter bases are located on an exterior wall then no encasement is required. It is preferable that meter rooms be accessible without requiring entry into the building itself. Situations will be evaluated on a case-by-case basis, with MTEMC having the final decision making authority as to the acceptability of the proposed location. Further, it is preferable that meter rooms NOT have a door or gate, locking or otherwise. However, when a locked gate or door is required and approved by MTEMC, the customer shall either: Provide and install a NEMA 3R key box adjacent to the meter room door or gate with provisions for an MTEMC padlock. (7/16 th inch shank) Customer shall provide a key to the door or gate which will remain in the key box at all times. Or In the case of a gate, the use of a chain and lock for securing the entrance into the meter room is acceptable. MTEMC shall place its padlock in the chain in such a way that only the MTEMC key will be required to gain entry into the meter room. Access is a critical issue for MTEMC related to its facilities. If access to the meter room is not possible due to key or lock issues, MTEMC reserves the right to remove the door or gate and is not responsible for any damages to those or for reinstalling them in the future. Meter rooms shall not be used for other purposes such as storage closets, maintenance areas, etc. Meter bases shall be surface mounted. Flush mounted or recessed meter installations are not acceptable. If the acceptance of a meter room by MTEMC requires additional communication infrastructure related to the reading of the meters by the MTEMC AMI system, the additional costs will be the responsibility of the customer.

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24 MTEMC Office Locations FRANKLIN 2156 Curd Lane Franklin, Tennessee LEBANON 201 Maddox-Simpson Parkway Lebanon, Tennessee Mt JULIET 1475 North Mt. Juliet Road Mt. Juliet, Tennessee WOODBURY 911 West Main Woodbury, Tennessee SMYRNA 317 S. Lowry Street Smyrna, Tennessee MURFREESBORO 326 St. Andrews Drive Murfreesboro, Tennessee CORPORATE 555 New Salem Road Murfreesboro, Tennessee Customer Service: