Residential Building Plan Review Additions and New Home Construction

Transcription

1 Residential Building Plan Review Additions and New Home Construction Submittal Requirements Documents to be Submitted A completed and signed permit application and signed cover sheet. Building Plans Provide Two Copies of the Following: Plot Plan. The site plan should include the lot size with adjacent streets and the location and size of all existing and proposed buildings on the site. Footing/Foundation Plan. Footing plan to include the size, locations and type of footings and foundation. Provide sections for each type of foundation / foundation wall. Label materials, size and spacing of reinforcing, insulation type and thickness, Radon system, etc. Floor Plans. A floor plan is required for each level of the building. Label each room or area for its specific use. Provide sizing for windows, doors, beams and headers sizes on the plan. Include such things as CO and smoke detector locations, bathroom fan indications, attic access locations, truss orientation and spacing, and air conditioner location. Front, Rear and Side Elevations. Elevations provide an illustration of the exterior finishes, grading, overhangs, etc. Wall Sections and Building Cross-Sections. Sections are needed to review the structure and its elements. Label all building materials on the sections. Radon Plan. [ ] Completed permit application or include with the building permit. Provide a plan view drawing of the radon underground layout and include radon vent pipe on the building cross section drawing. Radon pipe must be identified with at least one label on each story and in attics and crawl spaces. The label must read: Radon Gas Vent System." Mechanical. Completed permit application. Provide a plan view drawing of the ductwork layout. An overlay highlight of the floor plan(s) is acceptable. See MN Construction Documents information for specific submittals such as duct sealing materials and methods. When HVAC ductwork is outside the building envelope, provide the method of pressure testing and person responsible for the testing. Plumbing Submittals. Completed permit application and isometric of the proposed plumbing system. Materials, sizing, type, etc., must be labeled on the diagram. See MN Construction Documents information for specific submittals such as pipe insulation and required locations [MN 1322.R and Table R ]. Construction Documents/Energy Code. See reverse side of this page. Alternate Methods and/or materials (AMM) are materials not specifically regulated by the code, such as anchor straps, wood I-joist, house wrap products, composite deck materials, etc. Submittals of proposed AMM must be accompanied with related ES/ICC Reports, third party testing results, or equal. AMM manufacturer s installation instructions (MII) may be required at application to determine compliance and MII must be provided on site at the time of inspection. Storm Water. All lots that are part of a subdivision in which an NPDES Storm Water Permit was required must submit a copy of the permit or Subdivision Registration form as well as the Storm Water Pollution Prevention Plan (SWPPP) for the site. Other Permits. Permits are required for retaining walls over four feet, fences, fireplaces, curb cuts, etc. Electrical Work. Questions about electrical permits or proposed electrical work may be directed to Electrical Inspector James Herman at Zoning Information All work is subject to Brainerd Zoning Ordinance requirements. Requirements include setbacks from property lines, maximum lot coverage, maximum size and number of accessory buildings, building height, exterior material and building appearance. Also, property within one thousand (1,000) feet of a lake and three hundred (300) feet of the Mississippi River are subject to Shoreland Regulations. Attached is a site plan example and zoning requirements for accessory buildings. All other zoning and shoreland requirements can be found on the City s website. City of Brainerd Building Department Laurel Street (Fax) Brainerd MN 56401

2 MN Construction Documents Construction documents shall be drawn to scale upon suitable material. Electronic media documents are permitted to be submitted when approved by the building official. Construction documents shall be of sufficient clarity to indicate the location; nature, and extent of the work proposed, and show in sufficient detail pertinent data and features of the building, systems, and equipment as herein governed. The detail shall include the following when applicable: A. Insulation materials and the R-values; B. Fenestration U-factors and SHGCs; C. Area-weighted U-factor and SHGC calculations; D. Mechanical system design criteria; E. Mechanical and service water heating system and equipment types, sizes, and efficiencies; F. Equipment and systems controls; G. Fan motor horsepower (hp) and controls; H. Duct sealing, and the location and insulation of ducts and pipes; I. Lighting fixture schedule with wattage and control narrative; and J. Air sealing details. Summary of above listed construction documents A. Insulation materials and the R-values: Insulation minimum values may be located in MN Chapter 1322 Table R The values may be illustrated on the building plans and cross sections or may be written in a word document or equal. [See Table R ].* B. Fenestration U-factors and SHGC: The window and door U-factors may be illustrated on the building plans and cross sections or may be written in a word document or equal. Window and door units that lack a U-value and SHGC label or certified rating shall be assigned a default value from one of the three (3) Tables in R303.* C. Area-weighted U-factor and SHGC calculations.* D. Mechanical system design criteria: HVAC equipment shall be sized per R , either with an ACCA Manual S or equal, or the ACCA Manual J. Oversizing of heating equipment shall not exceed 40 percent of the calculated load requirements and oversizing of cooling equipment shall not exceed 15 percent of the calculated load requirements. Design conditions area 82/72 Summer Db/Wb degrees and -24 Winter Db degrees F. [Table R ]. Submit the specifications for all proposed equipment. Mechanical ventilation is mandatory per MN Energy 1322 section R Tables R and R must be used to determine the ventilation minimums. Submit all components related to ventilation and exhaust. The submittal may be a list, a narrative, or as part of the project plans and specifications.* E. Mechanical and service water heating system and equipment types, sizes, and efficiencies: Provide in list form the equipment types, sizes, and efficiencies being proposed for heating water. Water supply line insulation must be installed per MN Energy code Chapter 1322 Table R and provided as specified in section R * F. Equipment and systems controls: Provide in list form the proposed equipment controls. At least one thermostat must be a programmable type capable of maintaining temperatures down to 55 degrees F. or up to 85 degrees F. The programmable thermostat shall be initially programmed with a heating temperature set point no higher than 70 degrees F. and a cooling temperature set point no lower than 78 degrees F. The mechanical ventilation system controls shall comply with MN 1322.R Determine applicability of R , items #1 backflow damper, #2 compatibility, #3 compatibility, and #4 accessible and labeled.* G. Fan motor horsepower (hp) and controls, for proposed equipment as applicable. H. Duct sealing, and the location and insulation of ducts and pipes: HVAC: Provide in list form the materials proposed for ducts, duct insulation, and duct sealing [Section of the MN mechanical code, MN 1322.R insulation, R Sealing]. Submit product specifications providing minimum R-value insulation as determined in Table R Include bathroom exhaust, clothes dryer exhaust, air exchange duct systems, etc. Plumbing: Provide in list form the proposed potable water piping and insulation products, MII and location of water lines [MN 1322.R403.4 Service hot water systems, R Hot water pipe insulation].* I. Lighting fixture schedule with wattage and control narrative. A minimum 75 percent of the permanently installed lighting fixtures shall contain only high efficacy lamps. Submit a lighting schedule including the lighting fixtures and controls, fixture locations, and efficacy. J. Air sealing details: [MN ] Submit air sealing details for the interior and exterior air barrier. Provide a list of proposed materials and a written description of the typical interior sealing products and installation methods. Provide a list of proposed exterior water resistant barrier materials and MII flashing details for such areas as the windows, doors, and misc. penetrations such as the dryer duct (round penetrations). *Required item on the New Construction Energy Code Compliance Certificate

3 APPLICATION FOR RESIDENTIAL ADDITIONS AND NEW CONSTRUCTION BUILDING PERMIT CITY OF BRAINERD DEPARTMENT OF BUILDING SAFETY CITY HALL 501 LAUREL STREET BRAINERD, MN (218) FAX (218) APPLICATION MUST BE COMPLETED IN ITS ENTIRETY BEFORE A BUILDING PERMIT WILL BE ISSUED SITE ADDRESS Suite/Unit No. LEGAL DESCRIPTION: Lot Block Subdivision (Legal description may be found on the real estate tax statement or by calling ) APPLICANT (check one): OWNER CONTRACTOR ARCHITECT/ENGINEER Owner/Buyer Information Name Contact Person Address City State Zip Phone Cell Phone * Do you Homestead this property? (check one) YES NO Owner Initials Contractor Information Name Address City State Zip Phone Cell Phone * Architect/Engineer Information (if applicable) Name Address City State Zip Phone Cell Phone *

4 TYPE OF STRUCTURE (check one only) Single Family Residential Single Family Attached Two Family Residential Three/Four Family Residential Five + Family Residential Other, describe Estimated Start Date: NON-COMPLYING SEPTIC SYSTEM If your septic system is not in compliance with Chapter 7080 (the minimum technical standards for individual sewage treatment systems), NO BUILDING PERMIT will be issued until such time that it has been upgraded or brought in to compliance. Should failure or non-compliance occur between November 15 and April 15, a Winter Window Agreement is available for postponement of compliance until the following June 1. CHECK ONE: Municipal sewer serves this property. Valuation = Total cost of labor & materials. List a valuation for each of the following categories where applicable. This property is served by septic system (compliance report is required). Building: $ HVAC: $ Plumbing: $ Electrical: $ TOTAL: $ Timeline for Building Permit Applications The Department of Building Safety strives to meet the following standards for reviewing plans, issuing permits and conducting inspections. During the peak construction season, the number of plan submittals may occasionally affect the Department s ability to meet these standards. Applications for permits should always be submitted as early as possible so as not to delay construction. Information sheets are available to help customers know what constitutes a complete permit application and complete work for an inspection. New Construction and Remodeling for Single-Family and Two-Family Buildings: Ten business days upon receipt of completed application and materials. Up to three additional working days may be needed to evaluate revised plans and information. Inspection Request: Inspection requests for specific times will be honored whenever possible. If the requested time is not available, the customer will be advised so that an alternate time can be selected. Twenty-four hours advance notice is requested. Description of Proposed Work: I HEREBY APPLY FOR a Building Permit and I acknowledge that the information above is complete and accurate; that the work will be in conformance with the ordinances and codes of the City of Brainerd and with the 2007 Minnesota State Building Code (MSBC). I understand this is not a permit, but only an application for a permit; and work is not to start without a permit that the work will be in accordance with the approved plan in the case of all work which requires plan review and approval of plans. Applicant s Signature Date Print Name * REQUIRED

5 3 JOB ADDRESS: Names of all contractors and subcontractors must be provided before a building permit will be issued. GENERAL CONTRACTOR SEWER/WATER/SEPTIC ADDRESS ADDRESS CITY / STATE / ZIP CITY / STATE / ZIP PHONE NO. PHONE NO. LICENSE NO. LICENSE NO. * * CONCRETE/MASONRY PLUMBING ADDRESS ADDRESS CITY / STATE / ZIP CITY / STATE / ZIP PHONE NO. PHONE NO. LICENSE NO. LICENSE NO. * * FRAME WORK ROOFING ADDRESS ADDRESS CITY / STATE / ZIP CITY / STATE / ZIP PHONE NO. PHONE NO. LICENSE NO. LICENSE NO. * * EXCAVATOR GYPSUM BOARD ADDRESS ADDRESS CITY / STATE / ZIP CITY / STATE / ZIP PHONE NO. PHONE NO. LICENSE NO. LICENSE NO. * * HVAC OVERHEAD DOOR(S) ADDRESS ADDRESS CITY / STATE / ZIP CITY / STATE / ZIP PHONE NO. PHONE NO. LICENSE NO. LICENSE NO. * *

6 City of Brainerd/Crow Wing County E-911 REQUEST NEW ADDRESS FOR NEW CONSTRUCTION Name of Applicant: Contact Phone Number: Current Mailing Address: City, State, Zip Code: Please Fill Out Completely and Accurately: Name of the road your driveway intersects: Which side of the road is your structure? North South East West With the addition of this structure, will the driveway service more than two Residential or Commercial structures? Yes No How many houses/businesses will use the same driveway? Describe how the driveway location will be marked: Is the driveway already in place & usable? Yes No (Location must be marked) ***Failure to mark driveway with something distinctive (name, stake, lathe, ribbon, etc.), will delay address assignment!!!*** Real Estate Code/Parcel Number of the Property (15 Digits) Township Range Section # Resident s names or addresses of building sites on both sides of your driveway location: Driveway Location: (Must include an accurate description/sketch of driveway location in relation to properties in the area.) Please note that there will be a line item on your building permit described as an E-911 Addressing Fee. This charge covers City and/or County administrative costs as well as the cost of the blue and white fire number identification plate (if applicable). ***Be sure to mark your driveway location as indicated above, so that the new address can be assigned in 2 weeks. FOR CITY OF BRAINERD/CROW WING COUNTY USE ONLY BELOW THIS LINE Date Received: Government Jurisdiction ADDRESS ASSIGNED: City: MN Date Assigned: Field Work Date: Zip Code: By: By: NOTIFIED: Resident Post Office Sign Dept. Auditor City MSAG & ESN changes relayed to IES Fee Paid Receipt # Initial and Date

7 Property Owner Waiver Minnesota State Contractor Licensing Requirements The purpose of this form is to have property owners acknowledge their responsibilities to the Minnesota State Building Code, to Zoning Ordinances, and to other applicable rules and regulations when they are acting as general contractor on building projects. I understand that the State of Minnesota requires that all Residential Building Contractors, Remodelers, and Roofers, obtain a state license unless they qualify for a specific exemption from the licensing requirements. By signing this waiver, I attest to the fact that I am building or improving my property by myself. I claim to be exempt from the State License requirements because I am not in the business of building on speculation or for resale, and this is the first residential structure that I have built or improved in the past 24 months. I acknowledge that because I do not have a State License, I forfeit any mechanic s lien rights to which I may otherwise have been entitled under Minnesota State Statute Furthermore, I acknowledge that I may be hiring independent contractors to perform certain aspects of the construction or improvement of this property. Some of these contractors may be required to be licensed by the State of Minnesota. I understand that unlicensed residential contracting, remodeling, and/or roofing activity is a misdemeanor under Minnesota State Statute , subdivision 1, and that I forfeit my rights to reimbursement from the Contractor s Recovery Fund in the event that any contractors that I hire are unlicensed. I have also been informed and acknowledge that by listing myself as the contractor on this project, I am solely and personally responsible for any violations of the State Building Code and/or City Ordinances in connection with the work performed on the property. Signature of Property Owner Date Project Address Please return this signed waiver with the Building Permit Application. To determine whether a particular contractor is required to be licensed, or to check on the licensing status of an individual contractor, please call the Minnesota Department of Labor & Industry, Construction Codes and Licensing Division at (651) or toll-free at EPA Renovation, Repair, and Painting Program The RRP Rule affects contractors, property managers, and others who disturb lead-based paint during renovation. The RRP Rule requires that firms paid to perform renovation, repair, demolition, or painting work in pre-1978 housing and child-occupied facilities have their firm certified by EPA. Additionally, the Minnesota Legislature passed a law that is intended to work in conjunction with Federal lead law(s). Essentially, the law requires local municipal building departments to be part of this Federal mandate by requiring each municipal building department to verify contractor compliance with Federal mandated lead certification requirements at the time of permitting. Local building departments are not responsible for any additional type of enforcement of the law; but simply to verify firm certification compliance.

8

9 Plumbing Permit Application City of Brainerd 501 Laurel Street Brainerd, MN (fax) SITE ADDRESS PROJECT VALUATION DATE OWNER S NAME THE APPLICANT IS: (Check one) Property Owner Contractor OWNER S ADDRESS CITY STATE ZIP OWNER S PHONE NUMBER OWNER S ADDRESS CONTRACTOR S BUSINESS NAME CONTRACTOR S BUSINESS ADDRESS CONTRACTOR S ADDRESS CITY STATE ZIP CONTRACTOR S BUSINESS PHONE CONTRACTOR S CELL NUMBER PLUMBING CONTRACTOR STATE LICENSE NO. CITY LICENSE NO. DESCRIPTION OF WORK Number of Fixtures Water Closet Lavatory Bathtub Sink & Disposal Dishwasher Shower Floor Drain Stop Sink Wash Tray Drinking Fountain Lawn Sprinkler Water Piping Hydraulic Valve Rain Leader Other TOTAL FIXTURES Special Devices Future Rough In Set Fixture Beer Dispenser Water Treatment Catch Basin Water Heater Sump Plump Receiving Tank Manholes Area New Ground Run Water Piping Re-Inspection Blow Off Basin Other GAS PIPING Size Number of Openings Certification Permits are required for Electrical, Building, Heating, Ventilating and Air Conditioning. This permit becomes null and void if the work authorized is not commenced within 180 days of the date of issuance, or if the work is abandoned or suspended for a period of 180 days. All provisions of laws and Ordinances governing this type of work will be complied with whether specified herein or not. The granting of a permit does not presume to give authority to violate or cancel the provisions of any other Federal, State or Local law regulating construction or the performance of construction activities. This permit may be revoked at any time for due cause. I hereby certify that I have read and examined this application and know the same to be true and correct. APPLICANT S SIGNATURE DATE DOUBLE FEE YES NO PROPERTY ID OFFICE USE ONLY PERMIT NUMBER

10 Mechanical Permit Application City of Brainerd 501 Laurel Street Brainerd, MN (fax) SITE ADDRESS PROJECT VALUATION DATE OWNER S NAME OWNER S PHONE NUMBER OWNER S FAX NUMBER OWNER S ADDRESS CITY STATE ZIP CONTRACTOR S BUSINESS NAME CONTRACTOR S CITY LICENSE NUMBER CONTRACTOR S BUSINESS ADDRESS CITY STATE ZIP CONTRACTOR S PHONE NUMBER CONTRACTOR S FAX NUMBER IS THE CONTRACTOR THE APPLICANT? (Check one) YES NO OWNER S ADDRESS CONTRACTOR S ADDRESS DESCRIPTION OF WORK (INCLUDE COMBUSTION AIR & MAKE UP AIR NOTES) Forced Air Hot Water Ventilation Wood burner A/C Roof-top Unit Refrigeration Other: GAS PIPING SIZE NUMBER OF OPENINGS PROCESS PIPING SIZE NUMBER OF OPENINGS Existing Proposed Existing (2) Proposed (2) Number of Units: Make: Fuel: Flue Diameter: Input (BTU): CFM: Tons: H.P.: Unit Weight: Number of Units: Make: Fuel: Flue Diameter: Input (BTU): CFM: Tons: H.P.: Unit Weight: Number of Units: Make: Fuel: Flue Diameter: Input (BTU): CFM: Tons: H.P.: Unit Weight: Number of Units: Make: Fuel: Flue Diameter: Input (BTU): CFM: Tons: H.P.: Unit Weight: Certification Permits are required for Electrical, Building, Heating, Ventilating and Air Conditioning. This permit becomes null and void if the work authorized is not commenced within 180 days of the date of issuance, or if the work is abandoned or suspended for a period of 180 days. All provisions of laws and Ordinances governing this type of work will be complied with whether specified herein or not. The granting of a permit does not presume to give authority to violate or cancel the provisions of any other Federal, State or Local law regulating construction or the performance of construction activities. This permit may be revoked at any time for due cause. I hereby certify that I have read and examined this application and know the same to be true and correct. APPLICANT S SIGNATURE DATE DOUBLE FEE YES NO PROPERTY ID OFFICE USE ONLY PERMIT NUMBER

11 New Construction Energy Code Compliance Certificate Per R401.3 Certificate. A building certificate shall be posted on or in the electrical distribution panel. Date Certificate Posted Mailing Address of the Dwelling or Dwelling Unit City Name of Residential Contractor MN License Number THERMAL ENVELOPE Insulation Location Below Entire Slab Foundation Wall Perimeter of Slab on Grade Rim Joist (1st Floor) Rim Joist (2nd Floor+) Wall Ceiling, flat Ceiling, vaulted Bay Windows or cantilevered areas Floors over unconditioned area Describe other insulated areas Building envelope air tightness: Total R-Value of all Types of Insulation Non or Not Applicable Type: Check All That Apply Fiberglass, Blown Fiberglass, Batts Foam, Closed Cell Foam Open Cell Mineral Fiberboard Rigid, Extruded Polystyrene Rigid, Isocynurate Duct system air tightness: RADON CONTROL SYSTEM Passive (No Fan ) Active (With fan and monometer or other system monitoring device ) Location (or future location) of Fan: Other Please Describe Here Windows & Doors Heating or Cooling Ducts Outside Conditioned Spaces Average U-Factor (excludes skylights and one door ) U: Solar Heat Gain Coefficient (SHGC): Not applicable, all ducts located in conditioned space R-value MECHANICAL SYSTEMS Make-up Air Select a Type Appliances Heating System Domestic Water Cooling System Heater Not required per mech. code Fuel Type Manufacturer Model Rating or Size Efficiency Residential Load Calculation Location of fan(s), describe: Input in BTUS: AFUE or HSPF% Heat Recover Ventilator (HRV) Capacity in cfms: Energy Recover Ventilator (ERV) Capacity in cfms: Capacity in Gallons: Low: Low: Heating Gain Cooling Load Describe any additional or combined heating or cooling systems if installed: (e.g. two furnaces or air source heat pump with gas back-up furnace): Select Type Balanced Ventilation capacity in cfms: Heating Loss MECHANICAL VENTILATION SYSTEM Capacity continuous ventilation rate in cfms: Total ventilation (intermittent + continuous) rate in cfms: Output in Tons: SEER /EER High: High: Passive Powered Interlocked with exhaust device. Describe: Other, describe: Location of duct or system: Cfm's " round duct OR " metal duct Combustion Air Select a Type Not required per mech. code Passive Other, describe: Location of duct or system: Cfm's " round duct OR " metal duct Builders Associaton of Minnesota version

12

13