APPROVED MATERIALS LIST
|
|
|
- Alexander Robertson
- 10 years ago
- Views:
Transcription
1 APPROVED MATERIALS LIST STANDARD SPECIFICATIONS 2011 EDITION CENTRAL CONTRA COSTA SANITARY DISTRICT Revised 08/17/11
2 TABLE OF CONTENTS APPROVED MATERIALS LIST... 1 BEDDING AND BACKFILL MATERIALS... 3 GEOTEXTILE FABRIC... 4 CAST IRON FITTINGS... 5 CAST METAL PRODUCTS... 6 COUPLINGS... 7 HIGH DENSITY POLYETHYLENE COUPLINGS... 9 HOUSE SEWERS: 4 AND OVERFLOW PROTECTION DEVICES MAIN SEWERS: LESS THAN JOINT RESTRAINT SYSTEMS PIPE FITTINGS: LESS THAN 18 SEWERS TAPS READY-MIX DESIGNS PRECAST PRODUCTS CONCRETE CURING COMPOUNDS REINFORCED CONCRETE UTILITY BOXES PUMP SYSTEMS GREASE TRAPS MISCELLANEOUS APPROVED MATERIALS MISCELLANEOUS APPROVED MATERIALS
3 Bedding and Backfill Materials Bedding Type, Backfill Description: TYPE MATERIAL DESCRIPTION CLSM Controlled Low Strength Material Coarse Type 1 Drain or Foundation Rock Crushed stone or gravel (Not mined alluvial material) Minimum of 95% crushed particles Durability Index of 40 Class 2 Aggregate Base Newly quarried or recycled material (Not mined alluvial material) Three-quarter (3/4) inch maximum grading Type 3 Type 3 Select Native material from trench excavation Free of vegetable matter, debris and refuse, concrete, stones or clods larger than four (4) inches Native Material from trench excavation Particles must not exceed three-quarter (3/4) inch in diameter Free of vegetable matter, debris and refuse, concrete, stones or clods larger than four (4) inches 3
4 Geotextile Fabric Description: Geotextile fabric Geotextile fabric for paving and wrapping foundation rock. FABRIC FOR WRAPPING FOUNDATION ROCK FABRIC FOR PAVING Manufacturer Product Mirafi 600X US Fabrics US 315 Webtec HD Carthdage Mills FX-66 Amoco 2006 Propex 300 ST SKAP W315 Thrace/Linq GTF 300 Mirafi Mirapave 400 US Fabrics US 90P Webtec OL Carthdage Mills FX-38 OL Amoco 4599 Petromat Propex 381 SKAP GC 130 Thrace/Linq 130 EX 4
5 Cast Iron Fittings Combination Wye 1/8 Bend Long Sweep Quarter Bend and (1/8) Bend P Trap Reducer Reducing Combination San Tee 1/16 Bend Two Way Combination (Clean Out Only) Note: Other fittings may be accepted under special use approval. Contact the District Inspector for such circumstances. All fittings to be four inch (4 ) or larger. Wye Twin Cleanout 5
6 Cast Metal Products Manufacturer: Manhole frames, Covers, Rodding Inlets, Adjustment Rings Cast Metal Products such as Manhole Frames, Covers, Rodding Inlets and Adjustment Rings can be obtained from but are not limited to the following approved manufacturers: 1. D&L Foundry and Supply Phone Number: (707) South Bay Foundry Phone Number: (209)
7 Couplings Description: Manufacturer: Banded Rubber Couplings For repairs, alterations and house sewers with connections of dissimilar materials. Banded rubber couplings shall have four (4) clamps and metal shear bands. Manufacturers included but are not limited to: 1. Fernco 2. Mission 3. Husky Note: Check with Inspector prior to purchase of material to insure proper coupling is selected for the different pipe types encountered. Mission Band Seal Joints Calder Coupling Fernco Proflex Coupling 7
8 Husky 4 Clamp Coupling Fernco Stainless Steel Shear Rings (80 in-lb) (60 in-lb) Fernco Strong Back RC Couplings Fernco 5000 Series RC Couplings (60 in-lb) (60 in-lb) Fernco No-Hub Couplings Silver (60 in-lb) Yellow & Green (80 in-lb) Mission Adjustable Repair Coupling Anaco No Hub (60 in-lb) 8
9 High Density Polyethylene Couplings Friatec Frialen Electrofusion Coupling 9
10 House Sewers: 4 and 6 Pipe Description: Pipe material for house sewers in four (4) and six (6) inch in diameter. 1. PVC Solid Wall SDR 26 (Solvent Welded Joints) (Bell & Spigot Joints) 2. ABS Solid Wall Schedule 40 (Solvent Welded Joints) 3. Vitrified Clay Pipe (VCP) (Bell & Spigot Joints) (Plain Ended Joints) 4. DIP Class 52 (Bell & Spigot Joints) 5. Cast Iron Soil Pipe (CIP) Class SV (Bell & Spigot Joints) (No-Hub) 6. HDPE SDR 17 Gray (Ductile Iron Pipe O.D.) (Butt Thermal Fused Joints) (Pipe Bursting or Directional Drilling only or at Inspector s discretion) 7. PVC Solid Wall C900 (Bell & Spigot Joints) (DR-14, DR-18, DR-25) Note: HDPE SDR 17 shall be purchased in longest length practicable in order to achieve the minimum amount of pipe joints during construction. A maximum of ten (10) joints per one hundred foot (100) length of laid pipe shall be achieved, unless all joints are de-beaded. 10
11 Overflow Protection Devices Description: Overflow Protection Devices (OPD) Overflow protection devices prevent sewage from entering homes and businesses and reroute the spill outside the building. Manufacturer: Extendable Backwater Valve MANUFACTURER Mainline Backflow Products PRODUCT NAME Adapt-a-valve Inspection Chamber with Test-Eze Gate Feature Rector Seal Clean Check Backwater Valve "Mushroom" Genplex Kelly Backwater Device (No-Hub & IPS) Sewer Popper Stephens Corp Sewer Popper Model S Relief Cap Extendable Backwater Valves Unlimited Home Solutions LLC ( Sewer Relief Cap ABS PVC Mushroom OPD Sewer Popper OPD Sewer Relief Cap 11
12 Main Sewers: Less than 18 Description: Pipe Pipe material for sewers less than eighteen (18) inches in diameter. 1. PVC Solid Wall SDR 26 (Bell & Spigot Joints) 2. Ductile Iron CL52 (Bell & Spigot Joints) 3. PVC Solid Wall C900 or C905 (Bell & Spigot Joints) 4. HDPE SR 17 Gray (Ductile Iron Pipe Size O.D.) (Butt Fused Joints, de-beaded) 5. Vitrified Clay (Bell & Spigot Joints) Note: Special approval may be granted by CCCSD for other materials as necessary for the specific application. Material shall be purchased in longest length practicable in order to achieve the minimum number of pipe joints. Joint Restraint Systems DIP PVC MANUFACTURER American Ductile Iron Pipe U.S. Pipe U.S. Pipe BullDog Restraint System Certain Teed JOINT RESTRAINT SYSTEM Lok-Fast Restrained Joint TR FLEX Restrained Joint Field-Lok 350 Gaskets BullDog PVC Pressure Pipe Integrated Joint Restraint System Certa-Lok restrained joint system 12
13 Pipe Fittings: Less than 18 Sewers Description: Pipe fittings Pipe fittings for pipelines that are less than eighteen (18) inches in diameter. PIPE MATERIAL DIP PVC Solid VCP MANUFACTURER Plastic Trends CertainTeed FITTING Wye, Tee, 11 ¼ Fitting, Mechanical Fittings Wye, Tee, Closure Coupling Saddle Tee, 3 Fitting, 11 ¼ Fitting 90 Sweep Elbow Wye, Tee MAXIMUM FLEXIBLE ALLOWABLE FITTING FITTING DEFLECTION SDR 26 Gasketed Sewer Fitting 4 Cast Iron O.D. 5 Iron Pipe Size O.D. 5 90º Sweep Elbow Saddle Tee Fitting Wye, Tee Fitting for pressure side sewers SDR 26 Heavy Wall Gasketed Sewer Fitting 13
14 Taps Description: PIPE MATERIAL ABS Taps Tap materials for the corresponding type of main line sewer. MAINLINE TAP Sealtite Type S Saddle with four (4) band coupling ABS Saddle with solvent weld and two (2) stainless steel straps ACP Fowler Saddle CIP, DIP Fowler Saddle Sealtite Type S Saddle with four (4) band coupling HDPE Thermal-Fused Saddle Insituform Liner PVC Saddle with Rubber Gasket and two (2) stainless steel straps Sealtite Type S Saddle with four (4) band coupling PVC VCP PVC Saddle with Rubber Gasket and two (2) stainless steel straps PVC Saddle with solvent weld and two (2) stainless steel straps Fowler Saddle Sealtite Type S Saddle with four (4) band coupling Note: PVC taps may be done by any General Engineering ( A ) Contractor registered with CCCSD. All other taps must be done by either Tap-Tite Company or Roto- Rooter. ABS Saddle Fowler Saddle HDPE Saddle PVC Saddle 14
15 Ready-Mix Designs Manufacturer: Concrete mix 1. Central Concrete Supply Phone Number: (408) MIX DESIGNATION MIX DESIGN # Controlled Low Strength Material Cast-in-place Concrete F35138AA 1EF115Q C1 2. Cemex Phone Number: (650) MIX DESIGNATION MIX DESIGN # Controlled Low Strength Material Cast-in-place Concrete Precast Products Manufacturer: Precast Products such as Manhole Bases, Barrels, Cones, Grade Rings, Paving Rings, Adjustment Rings, Gaskets, Top Slabs, Grease Interceptors, Sampling Boxes and Sand-Oil Interceptors can be obtained from the following approved manufacturers. 1. Central Precast (US Concrete Precast Group) Phone Number: (925) Jensen Precast Phone Number: (707) Cook Concrete Products Phone Number: (530)
16 Concrete Curing Compounds Description: Concrete curing compounds Curing compounds shall be white pigmented and resin based. MANUFACTURER Master Builders Burke Company Euclid Chemical Company COMPOUND MB-429 Spartan Cote Cure-Seal Hardener Super Rez Seal Note: Sodium silicate compounds shall not be used. 16
17 Reinforced Concrete Utility Boxes Utility boxes for traffic and non-traffic areas Traffic Area Non-Traffic Area ITEM DESCRIPTION PRODUCT 12" x 12" Drain Box Christy V12 Box 10-3/8" I.D. x 12" Valve Box Christy or Jensen G5 Traffic Valve Cast Iron Grate (3/8" Max Spacing) H/20 Loading Christy V12-71W Welded Grate 8" I.D. x 12" Valve Box Christy or Jensen F8 Box 8-1/2" I.D. x 11-3/4" Drain Box Christy V1 Drain Box 10-5/8" I.D. x 17-1/4" Drain Box Christy V9 Drain Box Cast Iron Grate 3/4" Max Spacing Christy V1-71C Grate and V9-71C Grate Christy V12 Box Christy G5 Box Christy F8 Box Christy V12-71W Christy K-6004 Grate Christy V1-71C Welded Grate (Special Order) Grate 17
18 Pump Systems Description: Note: Pre-Approved Pump Systems, Pipe VENDOR SYSTEM PIPE MATERIAL E-One D-Series, W-Series, HDPE (SDR 11) I-Series and G-Series or PVC (Sch 40 or 80) Liberty Series, Pro370 HDPE (SDR 11) Series, Pro380 Series or PVC (Sch 40 or 80) Aqua Pro E-Series, EDP Series, HDPE (SDR 11) Pump Systems ESP-Series, SG-Series, or PVC (Sch 40 or 80) DG-Series Complete packages are required for Pre-Approved Pump Systems. This includes a pump, alarm panel, isolation and check valves, sump and sump extensions (as required). Individual parts of Pump System are not pre-approved by CCCSD. Models include but are not limited to the ones below, contact CCCSD for special approval of all others. E-One Model D-H071 Liberty 2448 Series E-One Model Gator Grinder Liberty Pro370-Series Liberty Pro380 Series Aqua Pro SG (2 discharge system, (2 discharge system, Required Access Riser) Required Access Riser) 18
19 Grease Traps (Referred to in the UPC as Hydromechanical Grease Interceptors) Grease Traps Description: Grease traps for trash enclosures with a 4 connector Manufacturers: 1. Zurn Phone Number: (805) Jay R. Smith Manufacturing Co. Phone Number: (334) Schier Products Phone Number: Dormont Phone Number: MANUFACTURER Zurn Jay R. Smith Manufacturing Company Schier Dormont PRODUCT Z1165, Z1170, Z1172, GT2700 Grease Interceptors Series PATG-2025, PATG-2420 WD Series PDI Certified Grease Interceptor Jay R. Smith Dormont Zurn Series WD Series Z1170 Schier Products Trapper II* PATG-2025 or PATG-2420 *Designed for indoor use only Note: Models without a standard 4 connector shall be upgraded to 4. 19
20 Miscellaneous Approved Materials MANUFACTURER PRODUCT D.E. Pentair Pool Products Product # 60 SEP Separation Tanks Hayward Pool Products Model # C9002 SEP Sika FI System with Sikadur Injection Gel Epoxy Epoxy Hilti HIT HY150 Adhesive Anchors Adhesive Anchors BASF Concresive 1420 Gel Epoxy Adhesive BASF Concresive Paste LPL Expanding - ITW Red Head, Trubolt Wedge Anchor Type Anchors Hilti Kwik-Bolt 3 Expansion Anchor Galvanizing Field Repairs Carboline Galvanox Glass Capsule Polyester Resin Hilti HVU Adhesive Capsule Adhesive Anchors HubSett Rector Seal HubSett J-K Polysource External Joint Wrap M-860 Manhole Sealing Henry Rubr-Nek External Joint Wrap Products ConSeal CS-50 Liquid Butyl Primer ConSeal CS-101 Butyl Sealant for Precast Structures Henry RAM-NEK Joint Sealant Transition Weld-On ABS to PVC Transition Cement Cements Oatey ABS to PVC Transition Green Solvent Cement Waterstops Newby Rubber Water Stop Ring 20
21 Miscellaneous Approved Materials Anchors Trubolt Wedge Anchor HVU Adhesive Capsule HIT HY150 Adhesive Anchor Miscellaneous Transition Cements Waterstop Rings HubSett Oatey ABS-PVC Weld-On ABS-PVC Cement Cement 21
Standard Specifications For Private Sewer Laterals
BUILDING SERVICES DEPARTMENT 250 Frank H. Ogawa Plaza, 2nd Floor, Oakland, CA 94612 Inspection Services: 510.238.3443 FAX: 510.238.2263 Standard Specifications For Private Sewer Laterals APPROVED MATERIALS
APPROVED MATERIALS LIST
ROSS VALLEY SANITARY DISTRICT SANITARY DISTRICT NO. 1 OF MARIN COUNTY APPROVED MATERIALS LIST APRIL 2015 2960 KERNER BOULEVARD, SAN RAFAEL, CA, 94901 April 2015 Page 1 of 27 TABLE OF CONTENTS TITLE PAGE...1
SUBDRAINS AND FOOTING DRAIN COLLECTORS. A. Construct subdrains, subdrain cleanouts and outlets, and footing drain collectors.
SUBDRAINS AND FOOTING DRAIN COLLECTORS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Subdrains B. Subdrain Cleanouts and Outlets C. Footing Drain Collectors D. Storm Sewer Service and Connections 1.02 DESCRIPTION
INDEX. Sec. No. Items Page Nos.
INDEX Sec. No. Items Page Nos. 1. Types of Pipe............... MSSP- 2 2. Concrete Pipe............... MSSP- 2 thru MSSP-3 3. ABS and PVC Truss Pipe............... MSSP- 3 4. ABS and PVC Solid Wall Pipe...............
Beacon Hill Sewer District Standard Specifications
Beacon Hill Sewer District Standard Specifications Residential Gravity Side Sewer Including Design Criteria and Standard Construction Drawings Residential Gravity Side Sewer Design Criteria 1. Provisions
SECTION 02630 STORM DRAINAGE SYSTEM
SECTION 02630 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for storm drainage systems including modifications and connections to existing storm drainage systems. 1.02 REFERENCE
32-02.05 Precast Manhole Sections and Castings. These items shall conform to Section 31, "Storm Drain Installation," of these Standard Provisions.
SECTION 32: SANITARY SEWER INSTALLATION 32-01 SCOPE. The Work shall consist of furnishing and installing sewer mains, manholes, laterals, cleanout fittings and appurtenances; and testing, flushing and
Town House 11265 Center Highway North Huntingdon, PA 15642
APPENDIX C SPECIFICATIONS FOR THE CONSTRUCTION OF BUILDING LATERAL SANITARY SEWERS DECEMBER 2004, INCLUDING AMENDMENTS ADOPTED ON FEBRUARY 6, 2008 AND APRIL 2, 2008; EFFECTIVE ON MAY 1, 2008 Town House
FY08 SEWER POINT REPAIRS BID TABULATION
6-07-831 Page 1 of 12 1 FOR CLEANING AND TELEVISING EXISTING SEWERS, AS SPECIFIED, ANY REQUIRED CLEANING, ANY LOCATION, ANY LENGTH OF SEWER, COMPLETE IN PLACE, FOR VARIOUS PIPE DIAMETERS. A. EXISTING "
SECTION 02401 - SANITARY SEWER PIPE
PART 1 - GENERAL 1.1 DESCRIPTION A. The WORK under this Section includes providing all labor, materials, tools and equipment necessary for furnishing and installing sanitary sewer pipe, in accordance with
FY11 Sanitary Sewer Main Rehab and Point Repair Bid Tabulation
644-10-569 Page 1 of 9 1 FOR CLEANING AND TELEVISING EXISTING SEWERS, AS SPECIFIED, ANY REQUIRED CLEANING, ANY LOCATION, ANY LENGTH OF SEWER, COMPLETE IN PLACE, FOR VARIOUS PIPE DIAMETERS. A. EXISTING
San Antonio Water System Standard Specifications for Construction ITEM NO. 854 SANITARY SEWER LATERALS
San Antonio Water System Standard Specifications for Construction ITEM NO. 854 SANITARY SEWER LATERALS 854.1 DESCRIPTION: This item shall govern sanitary sewer laterals installed in accordance with these
SECTION 08000 STORM DRAINAGE TABLE OF CONTENTS
SECTION 08000 STORM DRAINAGE 08010 DESIGN A. Location B. Sizing TABLE OF CONTENTS 08020 MATERIALS A. Pipe Materials B. Structure Materials C. Installation D. Inlets and Outlets 08030 INSPECTIONS AND TESTING
STANDARD SPECIFICATIONS FOR PRIVATE BUILDING SEWER LINES IN PUBLIC RIGHT-OF-WAY
STANDARD SPECIFICATIONS FOR PRIVATE BUILDING SEWER LINES IN PUBLIC RIGHT-OF-WAY Approved and adopted as Official Document Number 800576 this 10th day of December, 1980 Donald R. Boyd, P.E., Director Water
Model Specification 509 DRISCOPLEX 4200 and DRISCOPLEX 4300 Gravity Flow Sanitary Sewer
Model Specification 509 DRISCOPLEX 4200 and DRISCOPLEX 4300 Gravity Flow Sanitary Sewer The user may choose to adopt part or all of this Model Specification; however, the user should ensure that all parts
DIVISION 2 - SEWERAGE AND DRAINAGE SECTION 02720 - STORM DRAIN SYSTEMS PART 1 - GENERAL
DIVISION 2 - SEWERAGE AND DRAINAGE SECTION 02720 - STORM DRAIN SYSTEMS PART 1 - GENERAL 1.01 DESCRIPTION A. Furnish and install all storm drains, including manholes, inlets, service lines and other appurtenant
SECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS
SECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS PART 1 GENERAL 1.01 SECTION INCLUDES A. The requirements for pipe material and installation in sewer and drainage collection systems. All materials
BUILDING SEWER CONNECTION REQUIREMENTS
BUILDING SEWER CONNECTION REQUIREMENTS ANY PERSON DESIRING TO MAKE A NEW OR REVISED SEWER INSTALLATION MUST FIRST MAKE APPLICATION WITH THE NORTHERN GILA COUNT SANITARY DISTRICT FOR A PERMIT BEFORE STARTING
SECTION 02400 - STORM DRAIN SYSTEM
SECTION 02400 - STORM DRAIN SYSTEM CONTENTS: Part 1 - General... 1 1.01 Work Included... 1 1.02 Related Requirements... 1 1.03 Reference Standards... 1 1.04 Quality Assurance... 1 1.05 Measurement And
STANDARD SPECIFICATIONS SECTION 02701 INSTALLATION OF GRAVITY SEWER PIPELINES. 1. Trenching, Backfilling and Compacting: 02223
STANDARD SPECIFICATIONS SECTION 02701 INSTALLATION OF GRAVITY SEWER PIPELINES PART 1 - GENERAL A. Description This section describes the installation of gravity sewer pipelines fabricated of vitrified
SECTION 02732 BUILDING SEWERS. B. Connection of building sanitary drainage system to municipal sewers.
SECTION 02732 BUILDING SEWERS PART 1 GENERAL 1.01 SECTION INCLUDES A. Lateral piping, fittings, and accessories. B. Connection of building sanitary drainage system to municipal sewers. 1.02 REGULATORY
SERVICE LINE EXTENSION AND SERVICE LINE CONNECTION CONDENSED SANITARY SEWER SYSTEM INSTALLATION SPECIFICATIONS
1001 SOUTH LEECHBURG HILL LEECHBURG, PA 15656 Phone: 724-845-9355 Fax: 724-845-1186 SERVICE LINE EXTENSION AND SERVICE LINE CONNECTION CONDENSED SANITARY SEWER SYSTEM INSTALLATION SPECIFICATIONS 1. General
Sewage Compliance Form Instructions
CITY OF JOHNSTOWN DEPARTMENT OF COMMUNITY & ECONOMIC DEVELOPMENT 401 MAIN STREET ROOM 200 JOHNSTOWN, PA 15901 814-533-2017 FAX 814-539-5816 RENEE K. DALY DIRECTOR Sewage Compliance Form Instructions 1)
EXHIBIT "A. Technical Specifications for Water and Sewer Service Lines
EXHIBIT "A Technical Specifications for Water and Sewer Service Lines Water and Sewer Line Bedding and Backfill: Drawings show cross-section of trench, pipe laid on top of 6" min. bedding material, bedding
SECTION LS 2530 SANITARY SEWERS. A. General: Submit the following in accordance with The General Conditions.
SECTION LS 2530 SANITARY SEWERS PART 1 GENERAL 1.1 SUBMITTALS A. General: Submit the following in accordance with The General Conditions. 1. Product data for drainage piping specialties. 2. Shop drawings
SECTION 9.02 BUILDING SUBSURFACE DRAINS (PERIMETER, ETC.)
CHAPTER 9 SEWER / STORM DRAIN / IRRIGATION LINES SECTION 9.01 GENERAL This section covers the requirements for piping materials and installation of Lehi City sewer, storm drainage and irrigation collection
Specification for Pipe Bursting Gravity Sewer Mains with HDPE Pipe
Specification for Pipe Bursting Gravity Sewer Mains with HDPE Pipe 1. GENERAL The following supplemental sewer main specifications are intended to address the installation of high-density polyethylene
3. Contractor shall ensure that all permits are obtained prior to any construction. Contractor shall be responsible for all utility fees.
The following shall serve as the minimum requirements for contractors performing work in relation to the Authority s potable water and sanitary sewer system(s), appurtenances and service connections. General:
DESIGN AND CONSTRUCTION GUIDELINES AND STANDARDS DIVISION 33 UTILITIES 33 00 00 SITE UTILITIES
SECTION INCLUDES Domestic Water Fire Water Service Water Well Sanitary Sewer Storm Drains Foundation Drainage RELATED SECTIONS 03 30 00 Concrete 21 00 00 Fire Suppression - Sprinklers 22 00 00 Plumbing
SECTION 02763 POINT REPAIRS TO SANITARY SEWERS. A. Repairs to existing sewer lines by replacing short lengths of failed pipe.
SECTION 02763 PART 1 G E N E R A L 1.01 SECTION INCLUDES A. Repairs to existing sewer lines by replacing short lengths of failed pipe. 1.02 UNIT PRICES A. Measurement for point repairs is on a unit price
A. Contractor shall furnish, to the Engineer, all materials certifications available from the manufacturer for all required materials.
PART 1 GENERAL 1.1 SCOPE A. This item shall include the work necessary for the installation of storm sewer line construction. B. Reference Section 3800 Trenching and Backfill and the General Conditions,
San Antonio Water System Standard Specifications for Construction ITEM NO. 1100 SLIP-LINING SANITARY SEWERS
ITEM NO. 1100 SLIP-LINING SANITARY SEWERS 1100.1 DESCRIPTION: This item shall consist of slip-lining sanitary sewer pipe, which is accomplished by pulling or pushing liner pipe into existing sewers by
SECTION 33 11 00.11 POLYVINYL CHLORIDE (PVC) PIPE
SECTION 33 11 00.11 POLYVINYL CHLORIDE (PVC) PIPE PART 1: GENERAL 1.01 SECTION INCLUDES PVC pressure pipe and fabricated fittings in nominal sizes 4-inches through 12-inches with cast iron pipe equivalent
Section 2100-Trenching and Tunneling
SECTION 5200 - STORM SEWER PART 1 - GENERAL 1.01 SCOPE: This Section covers installation of storm sewer mains and culverts. Topics include permits and fees, trench widths, pipe laying, bedding, initial
SEPTIC SYSTEM CONSTRUCTION REQUIREMENTS ST. MARY S COUNTY HEALTH DEPARTMENT
SEPTIC SYSTEM CONSTRUCTION REQUIREMENTS ST. MARY S COUNTY HEALTH DEPARTMENT The following are minimum requirements for installation of conventional trench sewage disposal systems in St. Mary s County,
SECTION 200: STORM SEWER CONSTRUCTION STANDARDS
SECTION 200: STORM SEWER CONSTRUCTION STANDARDS Page No. Description 200-2 201 GENERAL 200-2 201.1 SPECIFICATIONS 200-2 201.2 CONNECTION TO EXISTING FACILITIES 200-3 202 MATERIALS 200-3 202.1 PIPES 200-4
Specifications for Residential Property Owners Connection to New Public Sewer
Specifications for Residential Property Owners Connection to New Public Sewer Spalding Tract property owners are required to connect to the community sewer system when construction is complete and the
EFFECTIVE FEBRUARY 2014. note: drainage permit required to call for a dampproof inspection
EFFECTIVE FEBRUARY 2014 note: drainage permit required to call for a dampproof inspection 1. ROOF DRAINS/DECK DRAINS (INTERIOR ) All roof and deck drains within the perimeter of the building shall be APPROVED
LS 2540 SEWER LATERALS AND INSPECTION TEES
LS 2540 SEWER LATERALS AND INSPECTION TEES A. Summary B. Submittals C. Site Information D. Sewer Pipe and Fittings E. Lateral Locations F. Lateral Installation G. Inspection Tee Installation H. Removal
SECTION 6 SANITARY SEWER MAIN 6.01 SCOPE
6.01 SCOPE The work covered by this section of the specifications consists of the furnishing of all plant, labor, materials, equipment and supervision and performing all operations involved in the construction
SECTION 55 PIPE FOR STORM DRAINS AND CULVERTS (FAA D-701)
SECTION 55 PIPE FOR STORM DRAINS AND CULVERTS (FAA D-701) 55-1 GENERAL The Contractor shall perform all work required by the plans for construction of pipe for storm drains, precast polymer trench drains
SECTION 221413 FACILITY STORM DRAINAGE PIPING
SECTION 221413 FACILITY STORM DRAINAGE PIPING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
SECTION 02110 - ASBESTOS CEMENT PIPE REPAIRS, DEMOLITION, AND DISPOSAL
SECTION 02110 - ASBESTOS CEMENT PIPE REPAIRS, DEMOLITION, AND DISPOSAL PART 1 - GENERAL 1.1 WORK INCLUDED IN THIS SECTION A. The WORK of this Section includes the repair, demolition, and disposal of asbestos
Jay R. Smith Mfg. Co.
Jay R. Smith Mfg. Co. Automatic Backwater Valve SMITH CUSTOMER DRIVEN FLOOD-GATE FEATURES Index Page Flood-Gate Features and Applications 2 How Flood-Gate Works 3 Flood-Gate Operation & Approvals 4 Valve
CHAPTER 6 - SANITARY SEWER
CHAPTER 6 - SANITARY SEWER 6.1 GENERAL This section covers the requirements for PVC plastic sewer pipe materials and installation in sanitary sewer construction. 6.2 PIPE PVC gravity sewer pipe and fittings
WATER & SEWER CORROSIVE RESISTANT PRODUCTS
WATER & SEWER CORROSIVE RESISTANT PRODUCTS The Standard of Excellence in the Industry CASING SPACERS COUPLINGS & FLANGE COUPLING ADAPTERS REPAIR CLAMPS DUCTILE IRON SADDLES STAINLESS STEEL SADDLES TAPPING
NORTH DAVIS SEWER DISTRICT STANDARD COLLECTION DETAILS
STANDARD COLLECTION DETAILS Detail No. Detail Title Pages ND-01 NOTICE TO CONTRACTORS 1 ND-02 MANHOLE CONSTRUCTION NOTES AND INDEX 2 ND-10 STANDARD MANHOLE CONNECTION 2 ND-11 STANDARD MANHOLE DETAIL 54"
SECTION 15125 HIGH DENSITY POLYETHYLENE (HDPE) PIPE AND FITTINGS FOR WATER DISTRIBUTION AND TRANSMISSION
SECTION 15125 HIGH DENSITY POLYETHYLENE (HDPE) PIPE AND FITTINGS FOR WATER DISTRIBUTION AND TRANSMISSION PART 1 GENERAL.01 SECTION INCLUDES Furnishing and installing 4 inch through 16 inch high density
SECTION 603 SANITARY SEWER FORCE MAINS
SECTION 603 SANITARY SEWER FORCE MAINS 1. GENERAL Pipelines for sanitary sewer force main systems shall conform to the following specifications and shall be installed at the locations indicated on the
SECTION 16402 UNDERGROUND ELECTRIC SERVICE
SECTION 16402 UNDERGROUND ELECTRIC SERVICE PART 1 GENERAL 1.1 SUMMARY A. Description of System 1. Furnish all labor, materials, and equipment for below grade work external to buildings as required, and
TECHNICAL SPECIFICATIONS GRAVITY AND PRESSURE SEWER LINE AND MATERIALS
TECHNICAL SPECIFICATIONS GRAVITY AND PRESSURE SEWER LINE AND MATERIALS Scope of Work Work performed under this contract shall consist of furnishing and installing, complete and ready for service, the sewer
See Appendix A for additional information, or contact ASTM directly.
DEFINITIONS Wherever used in these specification guidelines, the following words and terms have the meanings indicated. AREAWAY: A paved surface, serving as an entry area to a basement or subsurface portion
AIR RELEASE, CLEANOUT, AND SEWER MANHOLES
AIR RELEASE, CLEANOUT, AND SEWER MANHOLES **From Hartford IM BLDG(10) DESCRIPTION. This work shall consist of the construction of air release, cleanout, and sanitary sewer manholes; and the furnishing
Sewer Rehabilitation Design Requirements
Sanitary Sewer Overflow (SSO) Control and Wastewater Facilities Program Sewer Rehabilitation Design Requirements City of Baton Rouge/Parish of East Baton Rouge Department of Public Works Submitted by Prepared
City of West Linn Public Works Standard Construction Specifications. Table of Contents
City of West Linn Public Works Standard Construction Specifications Table of Contents DIVISION SIX STORM DRAIN TECHNICAL REQUIREMENTS... 1 601 PIPE AND FITTINGS... 1 601.01 Description...1 601.02 Materials...1
WATER MAIN CONSTRUCTION TECHNIQUES DEPARTMENT OF PUBLIC WORKS WATER & WASTEWATER DIVISION
WATER MAIN CONSTRUCTION TECHNIQUES Overview Water Main - Materials Specifications Installation Future? Water Main Materials Material Types There are various material types used for water mains, these include:
Special Specification 7021 Water Main and Sewer Line Replacements
Special Specification 7021 Water Main and Sewer Line Replacements 1. DESCRIPTION Furnish, install, or replace water pipe, water valves, water meters and boxes, water service connections, fire hydrant assemblies,
TECHNICAL SPECIFICATION
THOMAS - G-FLEX GFLEX TECH SPEC CONNECTING INNOVATION JOHANNESBURG TEL: +27 11 794 7594 CAPE TOWN TEL: +27 21 556 5258 POLOKWANE TEL: 015 298 9142 DESIGNER, MANUFACTURER AND DISTRIBUTOR OF PIPE CONNECTION,
San Antonio Water System Standard Specifications for Construction ITEM NO. 1103 POINT REPAIRS AND OBSTRUCTION REMOVALS
ITEM NO. 1103 POINT REPAIRS AND OBSTRUCTION REMOVALS 1103.1 DESCRIPTION: 1. Repair of sanitary sewer lines by replacing short lengths of failed pipe with new pipe. 2. Repair of service laterals located
CONTENTS. Yale University Design Standards. Underground Electrical Duct Bank. A. Summary. B. System Design and Performance Requirements
16600 Underground Electrical Duct Bank This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications
08003-1 WATER SERVICE 2
08003_Mar08_2011.pdf Page 1 of 7 INDEX Page 08003-1 WATER SERVICE 2 1.1 Pipe 2 1.1.1 Copper 2 1.1.2 Polyethylene 2 1.2 Valves and Fittings 2 1.2.1 Main Stops 3 1.2.2 Curb Stops 3 1.2.3 Curb Box 3 1.2.4
SECTION 15 AIR RELEASE VALVE ASSEMBLIES. 15-1 General
SECTION 15 AIR RELEASE VALVE ASSEMBLIES 15-1.01 Scope 15-1 General This section describes the requirements for furnishing and installing Air Release Valve Assemblies of the size and type shown on the plans,
Bethel Township Municipal Authority (BTMA) RESIDENTIAL SEWER CONNECTION MANUAL
155 E. Front Street (rear) Lititz, PA 17543 Phone (717) 625-1930 Fax (717) 625-1931 Bethel Township Municipal Authority (BTMA) RESIDENTIAL SEWER CONNECTION MANUAL CONSTRUCTION SPECIFICATIONS AND DETAILS
SECTION 02700 SEWERAGE AND DRAINAGE PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 02700 SEWERAGE AND DRAINAGE PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including the General and Supplementary Conditions and Division 1 Specification
Wastewater Collection System Supplemental Design Standards for Capital Improvement Program Projects
Wastewater Collection System Supplemental Design Standards for Capital Improvement Program Projects March 2013 i Metropolitan Sewer District of Greater Cincinnati Wastewater Collection System Supplemental
The Manitoba Water Services Board SECTION 027030 Standard Construction Specifications September 2013 Page 1 of 21
September 2013 Page 1 of 21 Part 1 General 1.1 DESCRIPTION OF WORK.1 The work described herein shall consist of the construction of sewers including: the supply and installation of pipe, saddles, tees,
SEWER BACKUPS & BASEMENT FLOODING PREVENTATIVE SOLUTIONS FOR THE BUILDING OWNER
Village of Shorewood, Wisconsin SEWER BACKUPS & BASEMENT FLOODING PREVENTATIVE SOLUTIONS FOR THE BUILDING OWNER Prepared By: Thomas A. Zoulek, P.E., LEED A.P. Vice President Mid City Plumbing & Heating
Exhibit A. Rules and Regulations for House Connections and Sewer Extensions
The purpose of this application example is to provide assistance to small and medium sized rural communities in the drafting of documents necessary for the efficient operation of water, wastewater, and
CW 2130 - GRAVITY SEWERS TABLE OF CONTENTS
August 2010 CW 2130 - GRAVITY SEWERS TABLE OF CONTENTS 1. DESCRIPTION... 1 1.1 General... 1 1.2 Definitions... 1 1.3 Referenced Standard Construction Specifications... 1 1.4 Referenced Standard Details...
2006 Codes. Please verify the following before calling for inspection
INSPECTION CHECKLIST RESIDENTIAL PLUMBING ROUGH IN 2006 Codes This checklist is intended for use to prepare for an inspection. This is only a general list and is not intended to address all possible conditions.
8.01 STORM SEWERS, CATCH BASIN LEADS, AND EXTENSIONS
8.01 STORM SEWERS, CATCH BASIN LEADS, AND EXTENSIONS 8.01.01 Description This work shall consist of installing lines of storm sewer pipe of the required inside diameter, and the necessary appurtenances,
The work of this Section includes furnishing and installing Reinforced Concrete Pressure Pipe as shown on the Drawings and as specified.
Section 33 0200- Page 1 of 4 PART 1 - GENERAL 1.1 DESCRIPTION OF WORK The work of this Section includes furnishing and installing Reinforced Concrete Pressure Pipe as shown on the Drawings and as specified.
STANDARD SPECIFICATIONS SECTION 03461 PRECAST REINFORCED CONCRETE MANHOLES AND MANHOLE BASES. 1. Structure Earthwork: 02200
STANDARD SPECIFICATIONS SECTION 03461 PRECAST REINFORCED CONCRETE MANHOLES AND MANHOLE BASES PART 1 - GENERAL A. Description This section includes materials, testing, and installation of precast concrete
General Guidelines for Repairing Buried PE Potable Water Pressure Pipes
515 General Guidelines for Repairing Buried PE Potable Water Pressure Pipes Introduction Traditional piping systems have gasket-sealed bell and spigot joints every 20 feet, which can be a potential maintenance
SIERRA LAKES COUNTY WATER DISTRICT P.O. Box 1039, Soda Springs, CA 95728-1039 (7300 Short Road, Serene Lakes)
SIERRA LAKES COUNTY WATER DISTRICT P.O. Box 1039, Soda Springs, CA 95728-1039 (7300 Short Road, Serene Lakes) Maintenance Office Administrative Office Billing Office 530-426-7802 530-426-7800 916-332-4872
ASTM C76, Class III, Wall B, except as modified herein. Clean natural sand, ASTM C33. Artificial or manufactured sand will not be permitted.
SECTION 3000 - SANITARY SEWERS 3001 SCOPE. This section applies to sanitary sewer construction and shall consist of furnishing all labor, materials, and equipment for the complete installation of sewers
volume of concrete occupied by the drain pipe in a cast-in-place structure or structure extension.
715.01 430 volume of concrete occupied by the drain pipe in a cast-in-place structure or structure extension. No additional payment will be made for the repair or replacement of existing concrete damaged
Customer Procedures and General Information for Sewer Customers
Customer Procedures and General Information for Sewer Customers Helpful Hints for Customers Ordinance Review of District and Customer Responsibility of New and Existing Sewer Lines Material and Manner
Section 02702 SEWER PIPE INSTALLATION AND TESTING
PART 1 - GENERAL Section 02702 SEWER PIPE INSTALLATION AND TESTING 1-1. SCOPE. This section covers the installation and testing of all sewer pipe furnished under the following specification sections: Concrete
Note: All dimensions are nominal. All weights are for shipping purposes only. Availability is subject to change.
CHANNEL DrAiNS Durable Designed for maximum durability and drainage, NDS Channel Drains are a proven alternative to traditional concrete drains. UV inhibitors in the grates, channel and component parts
INTERCEPTORS TABLE OF CONTENTS S-WD-INTER-1 0812
TABLE OF CONTENTS Pictorial Index Product Recommendations Grease Interceptors Commonly Specified Options Typical Installations Oil Interceptors Commonly Specified Options Typical Installations Sediment
Sanitary Sewer Mains and Services
Sewer Title Sanitary Sewer Mains and Services STitle Sewer Table of Contents "CORRECTIVE PERIOD & INSPECTION FOR SANITARY SEWERS & SERVICES"... 1 1. TERM OF GUARANTEE... 1 2. CONTRACTOR LICENSE AND PERMITS...
STANDARD SPECIFICATIONS FOR PUBLIC WORKS CONSTRUCTION CITY OF MANITOWOC, WISCONSIN SECTION 400 SEWER AND WATER CONSTRUCTION
STANDARD SPECIFICATIONS FOR PUBLIC WORKS CONSTRUCTION CITY OF MANITOWOC, WISCONSIN SECTION 400 SEWER AND WATER CONSTRUCTION Section Number Title 401 GENERAL 402 AMENDMENTS TO WSWS PART I - GENERAL CONDITIONS
SECTION 33 41 13 PUBLIC STORM UTILITY DRAINAGE PIPING
SECTION 33 41 13 PUBLIC STORM PART 1 - GENERAL 1.01 SECTION INCLUDES A. Storm drainage piping, fittings, and accessories at proposed station areas and locations other than under and immediately adjacent
MOBILE AREA WATER AND SEWER SYSTEM. Section 12. Sanitary Sewer Standard Specifications
MOBILE AREA WATER AND SEWER SYSTEM Section 12 Sanitary Sewer Standard Specifications May 31, 2012 TABLE OF CONTENTS 12.01 SCOPE:... 5 12.02 WORK INCLUDED:... 5 12.03 PIPELINE SYSTEM MATERIALS:... 5 A.
CONSTRUCTION CHECKLIST Residential Plumbing Rough-In September 2004
Bellevue Bothell Kenmore Kirkland Issaquah Mercer Island Sammamish Snoqualmie Woodinville CONSTRUCTION CHECKLIST Residential Plumbing Rough-In September 2004 This checklist is intended for use to prepare
Appendix A: Acceptable pipe and fitting materials
Watercare Services Limited Water and Code of Practice Content from the NZS 4404:2010 Land development and subdivision infrastructure has been reproduced for use in the Infrastructure Design s Manual for
Let Us Give Utilities the Respect that they Deserve.
Water & Sewer Utilities Miscellaneous Design and Plan Preparation Guidelines Issued by: Ray Mowla, P.E. Jefferson Parish Department of Engineering, Utilities Section The purpose of issuing these miscellaneous
ROOF DRAINS TABLE OF CONTENTS
Pictorial Index Product Recommendations Roof Drain Selection Factors Sizing Placement Material & Characteristics Pipe Connection Commonly Specified Options Typical Installations TABLE OF CONTENTS ROOF
September 2012 Brunswick County Engineering Department Revision 1.0. Technical Specification 020.01 GRAVITY SANITARY SEWER SYSTEM
1.0 General Technical Specification 020.01 GRAVITY SANITARY SEWER SYSTEM a) It is the intent of this specification to ensure that all gravity sewer system infrastructure constructed within the service
Native InDesign 2890 SaniTite Brochure 1/8" 100 300 CMYK April 17, 07
Sanitary Sewer Pipe Tough pipe for a tough environment SaniTite Sanitary Sewer Pipe delivers the features that engineers, contractors and municipalities demand durability, performance, handling, toughness
DIVISION 4300 STORM DRAINAGE
DIVISION 4300 STORM DRAINAGE SECTION 4305 STORM SEWER PART 1 - GENERAL 1.01 SCOPE This section covers the construction of storm sewers for the collection and transport of stormwater runoff. 1.02 REFERENCES
Quality & Innovation, Manufactured in the U.S.A.
Quality & Innovation, Manufactured in the U.S.A. Repair Clamps Couplings Expansion Joints Pipe Restraint Service Saddles Dismantling Joints Tapping Sleeves Tapping Machines HDPE Pipe Products Line-Stop
ARTICLE VI (ALTERNATE) STANDARD SPECIFICATIONS. for (PVC) SANITARY SEWER MAIN CONSTRUCTION
ARTICLE VI (ALTERNATE) STANDARD SPECIFICATIONS for (PVC) SANITARY SEWER MAIN CONSTRUCTION VI(A).1 General VI(A).2 Materials and Equipment VI(A).3 Installation of Sanitary Sewer Mains VI(A).4 Laying of
The Most Advanced Name in Drainage Systems. Sanitary Sewer Pipe
The Most Advanced Name in Drainage Systems Sanitary Sewer Pipe SaniTite Sanitary Sewer Pipe delivers the features that engineers, contractors and municipalities demand durability, performance, handling,
DESIGN AND CONSTRUCTION STANDARDS FOR SANITARY SEWER
DESIGN AND CONSTRUCTION STANDARDS FOR SANITARY SEWER SECTION 200.0 APPLICABILITY A. If public sewer is located within 250 feet of the proposed dwelling/dwellings, the owner is required to extend and connect