Thank you for choosing the wireless alarm system product

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Thank you for choosing the wireless alarm system product"

Transcription

1 Contents Preface Function Instruction About the host Function Setting Initialization System Settings Exit set 7 4. Password recovers.7 5. Factory Reset 7 6. Password and system time setting Engineering password setting user password settings system date setting system time setting Voice alarm telephone setting and deleting ~6 group user telephone number setting ~6 group user telephone number deleting ~2 group user SMS number setting ~2 group user SMS number deleting Coding or deleting Remote control and detector Coding to remote control Coding of detector Remote control deleting Single detector deleting All detectors deleting System function options settings Phone line broken alarm setting Tone of arming or disarming setting Siren ring time Arm delay time setting Delay time of Arm Phone alarm number of cycles Remote number of rings Keyboard password protection Record setting Network alarm settings Set the first and second groups of center number Delete center number User ID code set Arm and disarm the Upload Settings Alarm type set Zone type setting The wireless coding and timing arm and disarm settings First / second group of time arm set First / second group of time disarm set Timing arm and disarm switch settings Wireless siren coding settings Wireless smart appliance control History query Host state Day-to-day operations Out arm Home arm Host disarm Answer the alarm Remote control SMS remote control SOS additional function...28 Maintenance System detection Note Technical Parameters Schedule..39 [Preface] Thank you for choosing the wireless alarm system product Wireless alarm system adopts the most advanced digital sensing and controlling technologies, it is the intelligent alarm control system containing burglar alarm, fire alarm, fire fighting, gas leakage and SOS. Wireless alarm system uses the most advance multiple random selection technology, it avoids the problems of interference and alarm missing which exist usually in the similar systems. This system can be used widely in residence, shops, villa, and small enterprise and so on.

2 For you safety, before install and use, we suggest you to read this manual carefully. [Function Instruction] 1. An advanced and reliable communication technology, dialing alarm 2. 8 wired, 99 wireless defense zones 3. Remote control intelligent code, up to 5 wireless remote controls. 4. LCD display, built-in calendar clock, operates easily. 5. Full voice prompts, installation setting and daily operation are more easily. 6. Arm and disarm, and siren on/off are could be controlled by SMS instruction 7. SMS prompt of low power 8. SMS prompt of AC power broken and recover 9. Built-in intercom speaker, can achieve duplex intercom function 10. Built-in wireless transmitter module, wireless siren and smart home system can be linked 11. Preset 2 groups timing arm and disarm time 12. Calls out up to 6 phone numbers to notify you of abnormal conditions 13. Call out up to 2 phone numbers to notify the receiving alarm center. 14. Up to 2 SMS numbers to notify you of abnormal conditions seconds artificially recording message 16. Built-in digital voice, voice broadcast alarm situation automatically 17. Built-in English message, when alarm, the alarm information will be sent automatically 18. All arm and disarm function could be realized by one key 19. Multiple defense zones including instant, delay, 24 hours, bypass 20. Wireless coding: adding new accessories convenient, safe and efficient 21. Remote control: host arm, disarm, monitor, intercom, on / off alarm function alarm events can be recorded 23. Multiple arming modes such as timely arm by remote control, out arm delay by keypad etc. 24. Built-in AAA NI-HM rechargeable battery pack, power off alarm 25. Compatible with internationally accepted protocol Alarm Center: stability treasure Contact ID alarm communication protocol [About the host] The console shall be installed in the centre of the prevent site which could realize best receiving effect from all wireless detectors. Please note that keep the console away from large-sized metallic objects and home appliances producing high-frequency interference, and avoid steel-reinforced concrete and fire-proof doors. Alarm Panel Front Schematic Diagram: Alarm Panel Back Schematic Diagram: 2

3 Note: wired defense zone is from 81~88, Z1=81, Z8=88 in turn. [Function Setting] 1. Initialization Please insert SIM card and plug in Power, and then power on the system. It will show the GSM alarm system is good when built-in buzzer ring again per second with the signal light flashing again per seconds, and about 15 seconds a long ring with the signal is five cases on the screen. The single lights flash for every three seconds if the alarm system is good. Last, please turn on the backup battery switch. 2. System Settings In the setup process, press the [*] key to return to the previous level, pres the [ # ] key to repeat the current menu or to confirm function and operate according to the voice prompts, after entering the settings Enter four digits engineering password [XXXX] under the disarmed or armed state, and then input the [#] key to confirm. The host voice prompts: Please press 1 to set password and time; press 2 to set or delete alarm phone numbers; press 3 to program or delete wireless detectors and remote controllers; press 4 to go to the system options setup; press 5 to setup connection with external alarm center; please enter 6 to set alarm type and enter; 7 to set defense zone type; press 8 to set wireless encoding and scheduled Arm/disarm; Press 9 to check the system history log; press 0 for factory reset; press * to exit. Displaying [----], the host enter the setting state. During the setting status, operation of multiple functions can be repeated. If no operation during the voice prompts, hosts will automatically exit the settings and return to the standby state after two voice prompts. Note: engineering factory password is [6666]. Operating: [XXXX] [#] XXXX represents: a four-digit engineering password 3

4 3. Exit set After setting, you need to exit the setting state, press the [*] key continuously. Each time you press the [*] key are accompanied by a "beep". Generally pressing [*] twice continuously can return to the standby state. Operating: [*] [*] 4. Password recovers If forget the password or unable to operate the host, please recover password. In the arming or disarming status, enter the [ ] on the keyboard, and then enter [#] to confirm. The host has two short beeps. The hosts recover passwords successful and passwords backs to factory value. User password:1234;engineering password:6666 Operating:[ ] [#] 5. Factory Reset If the system is unstable, or forgets the previously setting parameters, etc., it is recommended that users restore factory value operation, re-set the host. Two ways of factory reset: First: In disarm status, use keypad to enter [ ] and press [#] to confirm, all the Led indications will be on for 2 seconds and you will hear a long beep. The host gets all its settings cleared and restores to its factory settings successfully. Operating method:[ ] [#] four-digit user password, all the Led indications will be on for 2 seconds and you will hear a long beep. The host gets all its settings cleared and restores to its factory settings successfully. Setting method:[0] [XXXX] XXXX represents:four digit user password Operating:[0] [1234] 6. Password and system time setting Enter the settings according to the main menu after the voice prompt, press 1 to enter the password and system time setting. Then you will hear that: To set the administrator password, please press 1; for user password, press 2; for date, press 3; for time, press 4; To return to the previous menu press *, To replay please press #. Accord the voice prompt to start different operating. 6.1 Engineering password setting Enter the password and system time setting, press the [1] on keypad, voice prompt: Please input a 4-digit password. After new password were inputting, Voice prompt: Setting completed. Fault engineering is:6666 Operating:[1] [1] [XXXX] XXXX represents:4- Digits new engineering password Example: change engineering password to 3928 Operating: [1] [1] [3928] Second: Enter settings, according the voice prompt of the main menu, press 0 to restore the state of the system settings. Then you will continue to hear the following voice: "Please input password. According voice prompt to enter a 6.2 User password settings After entering the password system time settings, press [2] on keypad, voice prompt: Please input a 4-digit password. A 4- digits new user password is 4

5 entered, the voice prompts: Setting completed ". User password changed successfully. The default user password is: 1234 Operating:[1] [2] [XXXX] XXXX represents:4- Digits new user password Example:change user password to 3405; Operating:[1] [2] [3405] After entering the password and system time setting, you press [3] on keypad please. Voice prompts: Please input a four-digit system time. A four-digit system time is entered, the voice prompts: Setting completed. System time is changed successful. Operating:[1] [4] [DD] [EE] DD represents: the number of hours of the current time (24-hour). EE represents: the number of minutes of the current time. Example: time is set to 7:51 AM Operating:[1] [4] [07] [51] 6.3 System date setting After entering the password and system time settings, you press [3] on keypad please. Voice prompts: "Please input a six-digit system date. A six-digit system date is entered, the voice prompts: Setting completed. System date is changed successful. Operating: [1] [3] [AA] [BB] [CC] AA represents: the current year after a two-digit BB represents: two digits of the current month CC represents: two digits of the current date Example: the date is set to Operating: [1] [3] [12] [07] [01] 6.4 System time setting 7. Voice alarm telephone setting and deleting After entering the settings, you press 2 to enter the voice alarm call set and delete settings according to the main menu of voice prompts. Then you will continue to hear the following voice: Please press 1 to set the first alarm phone number, press 2 to set the second phone number, press 3 to set the third phone number, press 4 to set the forth phone number, press 5 to set the fifth phone number, press 6 to set the sixth phone number; press 7 to set the first SMS alert phone number; press 8 to set the second SMS alert phone number. To return to the previous menu press [*],To replay please press #. According voice prompt to please press [1~8], Voice prompt: Set phone number, please press 1; delete phone number, please press 2. Accord the voice prompt to start different operating. Note: This version of the host does not have to set the SMS number, so the instruction of operation method is not written. 5

6 7.1 1~6 group user telephone number setting After voice Alarm phone settings and deleting, please according the voice prompt to press [1-6], voice prompts: To set phone number, please press 1; to delete phone number, please press 2 ". Then press [1] to set the phone number. Finished entering the phone number, press [#] to confirm. The voice prompts: "setting completed". The user's phone number is set successfully. Operating:[2] [1~6] [1] [XXXXXXXX] [#] 1~6 represents:the one set belongs the six telephone numbers. XXXXXXXX represents:user s telephone number Special note: If your phone is connected to the switch, and please add digital 0 or 9, otherwise the phone cannot dial out. Example:Set the first telephone number as Operating:[2] [1] [1] [ ] [#] 7.2 1~6 group user telephone number deleting After voice Alarm phone settings and deleting, please according the voice prompt to press [1-6], voice prompts: " To set phone number, please press 1; to delete phone number, please press 2". Then press [2] to delete the phone number. Finished entering the phone number, press [#] to confirm. The voice prompts: Delete completed". The user's phone number is set successfully. Operating:[2] [1~6] [2] 1~6 represents: The one detected belongs the six telephone numbers. Example:Delete the first telephone number Operating:[2] [1] [2] 7.3 1~2 group user SMS number setting After voice Alarm phone settings and deleting, please according the voice prompt to press [7~8], voice prompts: To set phone number, please press 1; to delete phone number, please press 2 ". Then press [1] to set the phone number. Finished entering the phone number, press [#] to confirm. The voice prompts: "setting completed". The user's phone number is set successfully. Operating:[2] [7~8] [1] [XXXXXXXX] [#] 7~8 represents:the one set belongs the two of SMS numbers. Example:Set the first telephone number as Operating:[2] [7] [1] [ ] [#] 7.4 1~6 group user telephone number deleting After voice Alarm phone settings and deleting, please according the voice prompt to press [7~8], voice prompts: " To set phone number, please press 1; to delete phone number, please press 2". Then press [2] to delete the phone number. Finished entering the phone number, press [#] to confirm. The voice prompts: Delete completed". The user's phone number is set successfully. Operating:[2] [7~8] [2] 7~8 represents:the one set belongs the two of SMS numbers. Example:Delete the first telephone number Operating:[2] [7] [2] 8. Coding or deleting Remote control and detector After entering the settings, please accord to the main menu of voice prompts to press 3 to enter a remote control / detector setting of the coding and deleting. Then you will continue to hear the following voice: Please press 1 to program remote 6

7 controllers, press 2 to program wireless detectors, press 3 to delete remote controllers, press 4 to delete one detector, press 5 to delete all detectors. To return to the previous menu press *, To replay please press #. Accord voice prompts to press [1~5]. Accord the voice prompt to start different operating. 8.1 Coding to remote control Remote control should be coded with the host, if want to control the host After enter the coding or deleting remote control and detector setting, accord voice prompt to press [1], you will hear: Please press any key on the remote controller. After pressing, voice prompts: Coding completed. If the remote control has been coded, voice prompts: Encoding repeat, coding failure. Note: If would like to continue to code next remotes, only need to then press any key of next remotes, press the [#] to exit the remote control code Operating:[3] [1] 8.2 Coding of detector Wireless detector should be coded with the host, in order to the host could trigger alarm by it. After enter the coding or deleting remote control and detector setting, accord voice prompt to press [2], voice prompt: Please enter a two-digit defense zone, between 02 to 99. Accord voice prompt to enter number of defense zones [02~99]. Voice prompt: please trigger detector. When detector was triggered, you will hear: coding completed. Operating:[3] [2] [02~99] 02~99 represents :Defense zones number of 02~99 Example: coding defense zones of 05 Operating:[3] [2] [05] 8.3 Remote control deleting The remote control has been deleted; it cannot be any operation of the alarm host After enter the coding or deleting remote control and detector setting, accord voice prompt to press [3], voice prompt: delete completed. all remote controls were deleted. Operating:[3] [3] 8.4 Single detector deleting. The detector has been deleted; it cannot be any operation of the alarm host. After enter the coding or deleting remote control and detector setting, accord voice prompt to press [4] : Please enter a two-digit defense zone, between 02 to 99. Accord voice prompts to press defense zone number [02~99]. Voice prompt : Deleted completed Single detector was deleted successful. Operating:[3] [4] [02~99] 02~99 represents :Defense zones number of 02~99 Example: coding defense zones of 05 Operating:[3] [4] [05] 8.5 All detectors deleting. The detector has been deleted; it cannot be any operation of the alarm host. After enter the coding or deleting remote control and detector setting, accord voice prompt to press [5], Voice prompt: Deleted completed All detectors were deleted successful. Operating:[3] [5] 9. System function options settings 7

8 Enter the settings according to the main menu after the voice prompt, and then press [4] to enter system function options setting. You will hear: Please press 1 to set the alarm for phone line error, press 2 to set siren on or off when arm or disarm, press 3 to set siren duration, press 4 to set arm delay, press 5 to set alarm delay, press 6 to set the number of cycles to call alarm phone, press 7 to set the number of ring times when calling from remote, press 8 to set password for access when arm/disarm by keypad, press 9 to enter voice recording; To return to the previous menu press *, To replay please press #. Please press [1~9] and start different operating according the voice prompt. 9.1 Phone line broken alarm setting Set phone line broken alarm could protect telephone line. In system function options setting states, according voice prompt to press [1], you will hear: Press 1 on, press 0 off. Press 1 or 0 according your request, finally you will hear that: setting completed. Phone line broken alarm was set successful. Factory fault: turn on Operating:[4] [1] [X] X=1 represents :Turn on X=0 represents :Turn off Example:Turn off phone line broken alarm function Operating:[4] [1] [0] 9.2 Tone of arming or disarming setting When arming or disarming, the operation will be prompted through external siren In system function options setting states, according voice prompt to press [2], you will hear: Press 1 on, press 0 off. Press [1] or [0] according your request, finally you will hear that: setting completed. Phone line broken alarm was set successful. Factory fault: turn on Setting method:[4] [2] [X] X=1:Arm/disarm prompt tone is on X=0:Arm/disarm prompt tone is off For example:arm and disarm the tone turned off operation Operating method:[4] [2] [0] 9.3 Siren ring time Enter into the system settings, according to voice prompts, press [3] on the keyboard, voice prompt: Please input two digits, between 00 to 15. Input the delay time [00 to 15] minutes. The last voice prompt: Setting completed ". Siren ring time setting successfully. Factory default: 3 minutes. Setting method:[4] [3] [XX] XX: [00~15] minutes For example: Siren rings 2 minutes operation Operating method:[4] [3] [02] 9.4 arm delay time setting Arm delay the host will delay a specific time before entering into armed state when the remote armed Enter into the system settings, voice prompts, press [4] on the keyboard, voice prompts: Please input two digits, between 00 to 99. Input the delay time [00 to 99] seconds. The last voice prompt: Setting completed ". Arm delay set successfully. The factory default: do not delay. Setting method: [4] [4] [XX] XX:[00~99]seconds For example:delay time of arm is 10 seconds Operating method:[4] [4] [10] 9.5 Delay time of Arm Arm delay: host will alarm in specific time when it receives the signal Enter into the system settings, voice prompts, press [5] on the keyboard, voice prompts: Please input two digits, between 00 to 99. Input the delay time [00 to 99] seconds. The last voice prompt: Setting completed ". Alarm delay set successfully. The factory default: do not delay. 8

9 Setting method:[4] [5] [XX] XX:[00~99] seconds For example: delay time of alarm is 10s Operating method:[4] [5] [10] 9.6 Phone alarm number of cycle s times Telephone dial - up cycle s times: Time of the host will dial the first group telephone number start from scratch again when all the numbers to dial out but did not put through. Enter into the system settings, voice prompts, press [6] on the keyboard, voice prompts: Please input two digits, between 00 to 15. Input the cycle s time [00 to 15] seconds. The last voice prompt: Setting completed. The phone alarm cycle s times successfully set. Factory default: 9 Setting method:[4] [6] [XX] XX:[00~15] times For example: The specific operation of the alarm 2 cycles. Operating method:[4] [6] [02] 9.7 Remote number of rings The ringing signal is issued by the switch send a regular pulse signal to the handset by detecting it to identify whether there is an incoming call, the handset here is the alarm host Into the system options settings, voice prompts, press on the keyboard [7] key, voice prompts: " Please input one digit, between 0 to 9.Enter the remote number of rings [0 ~ 9]. The last voice prompt: Setting completed ". Remote successfully set the number of rings. The factory default: 6. Note: If the remote number of rings is set to 0, it will turn off the remote control function Setting method: [4] [7] [X] X:[0 to 9] times Example: 2 times the number of rings to set up a remote operation. Operating method: [4] [7] [2] 9.8 Keyboard password protection The host keypad lock can guarantee that the host password is not malicious changed Into the system settings, voice prompts, press [8] key on the keyboard, voice prompts: Press 1 on, press 0 off ". If need turn on the keyboard password protection function, just press [1] key to turn it on, Press [0] to turn it off. The last voice prompt: Setting completed Keyboard password protection feature set successfully. Factory default: open. Setting method: [4] [8] [X] X=1represents: keyboard password protection feature is turned on X=0represents: keyboard password protectionisturnitoff. Example: turn the keyboard password protection. Operating method: [4] [8] [0] 9.9 Record setting Into the system settings, voice prompt, press the [9] key on the keyboard, hear the voice prompts: Please leave a message Recording icon [ ] long bright, 10-second clock countdown begin, recording begin: from the host 30cm, moderate voice recording in standard Mandarin user information; 10 seconds at the end of the end of the beep sound recording; same time, the host automatically start recording playback. Setting method: [4] [9] 10. Network alarm settings Enter into the settings according to the main menu after the voice prompts. Press [5] to enter the network alarm settings. Then you will continue to hear the following voice: Please press 1 to set the first alarm phone number, press 2 to set the second phone number, press 3 to set user ID, press 4 to set the arm/disarm uploading report. To return to the previous menu press *, To replay please press #. According to the voice prompts, press the button [1-4] key. Follow the voice 9

10 prompts different operation Set the first and second groups of center number The host networking alarm, it is necessary to set up your computer Alarm Center phone number to upload data communications After entering the network alarm settings, voice prompts, press [1 ~ 2] on the keyboard, voice prompts: " To set phone number, please press 1; to delete phone number, please press 2. Then, press [1] key to set. Finished entering the phone number, press [#] to confirm. The voice prompts: Setting completed Setting method:[5] [1~2] [1] [XXXXXXXX] [#] [1~2]:First set of numbers and second set of numbers XXXXXXXX:Center number Example: set the first set number of Setting method:[5] [1] [1] [ ] [#] LCD Display: 10.2 Delete center number After entering the network alarm settings, voice prompts, and press on [1 ~ 2] the keyboard, voice prompts: " To set phone number, please press 1; to delete phone number, please press 2. Then press [2] to delete the central telephone. The voice prompts: Setting completed Setting method: [5] [1~2] [2] [1~2]: to delete the first or second group center number Example: delete the first group of center number Operating method: [5] [1] [2] 10.3 User ID code set After entering the network alarm settings, voice prompts, press on the keyboard [3] key, voice prompted: Please enter a four-digit user ID. Then do it. Press the [#] key to confirm. The voice prompts: Setting completed " Setting method: [5] [3] [XXXX] [XXXX]: four-digit user coding Example: user encoding settings for 2245 Operating method: [5] [3] [2245} 10.4 Arm and disarm the Upload Settings After entering the network alarm settings, voice prompts, press [4] on the keyboard, voice prompts: Press 1 on, press 0 off The voice prompts: " Setting completed after you turn it on to upload or turn it off. Setting method: [5] [4] [X] X=1:Turn on arm and disarm the Upload Center X=0:Close to arm and disarm the Upload Center For example: turn it on of arm and disarm the upload center Operating method: [5] [4] [1] 11. Alarm type set Enter the settings according to the main menu of voice prompts, press [6] to enter the alarm set. Then you will continue to hear the following voice: Please input a two-digit defense zone between 02 to 99, followed by a one-digit alarm type: 0 is a bypass defense zone, 1 is real-time defense zone, 2 is stay at home defense zone, 3 is 24 hour defense zone. Please press # to confirm, press * to return ". Follow the voice prompts different operation. Enter the two-digit defense zone number [02 to 99] and an alarm type [0 ~ 3], press [#] key to confirm. The default alarm: Real-time defense zone Setting method: [6] [02 to 99] [X] [#] 10

11 02~99:02~99 defense number X=0:Bypass defense zones X=1:Real-time defense zone X=2:Stay at home defense zone X=3:24-hour defense zone Example: 46 defense zone is instant zone Operating method:[6] [46] [1] [#] 12. Defense zone type setting Enter into the settings according to the main menu of voice prompts to enter the zone typesetting, press [7]. Then you will continue to hear the following voice: Please enter the two digit number of defense zone, than input one digit number of defense zone type, 1. SOS 2.fire alarm 3.gas leak 4. Window alarm 5. Balcony alarm 6.Hall alarm 7.Magnetic contact alarm 8.perimeter alarm. Follow the voice prompts different operation Setting method:[7] [02~99] [X] 02~99:Defense zone number of 02~99 X=1: SOS alarm X=2: fire alarm X=3: gas leaks alarm X=4: window alarm X=5: balcony alarm X=6: hallalarm X=7: dooralarm X=8: boundary alarm Example: Set 41 zone as SOS alarm Operating method:[7] [41] [1] LCD display 13. The wireless coding and timing arm and disarm settings According to the main menu of voice prompts enter the settings, press [8] to enter the wireless coding and timing arm and disarm settings. Then you will continue to hear the following voice: Please press 1 to set first scheduled arm, press 2 to set second scheduled arm, press 3 to set first scheduled disarm, press 4 to set second scheduled disarm, press 5 to enable/disable arm/disarm schedule, press 6 to enter code for the wireless siren, press 7 for wireless home appliance control. To return to the previous menu press *, To replay please press #. Follow the voice prompts different operation First / second group of time arm set Time arm and time disarm are Convenient in the required time segment is armed of disarmed To enter the wireless coding and timing arm and disarm settings, voice prompts, and press [1~2] on the keyboard, voice prompts: Please enter a four-digit fixed time The input time arming time the voice prompts: Setting completed. Setting method: [8] [1~2] [AA] [BB] [1~2]: First / second group of time arm AA: Hour (24hours) BB: Minute Example: set first group arm time is 22:50 Operating method: [8] [1] [22] [50] 13.2 First / second group of time disarm set Time arm and time disarm are Convenient in the required time segment is armed or disarmed. 11

12 To enter the wireless coding and timing arm and disarm settings, voice prompts, and press [3~4] on the keyboard, voice prompts: Please enter a four-digit fixed time The input time disarming time. The voice prompts: "Setting completed Setting method:[8] [3~4] [AA] [BB] [3~4]:First / second group of time disarm AA: Hour (24hours) BB: Minute Example: set first group arm time is 7:51 Setting method:[8] [3] [07] [51] 13.3 Timing arm and disarm switch settings Only open timing arm and disarm switch, timing arm and disarm the timing to be effective Enter the wireless coding and timing cloth disarm setting, voice prompts, keyboard [ 5 ] key, voice prompts : " Press 1 on, press 0 off. After operation it successfully, voice prompts: "Setting completed Setting method:[8] [5] [X] X=1:Timing arm and disarm turned on X=0:Timing arm and disarm turned off Example:Turn on timing arm and disarm Operating method:[8] [5] [1] 13.4 Wireless siren coding settings Enter the wireless coding and timing arm/disarm setting, voice prompts, press [ 6 ] on the keyboard, voice prompts : " Please enter a eight-digit wireless address code. The wireless encoding of eight digits is only from 0-2.The last voice prompt: Setting completed. Setting method:[8] [6] [XXXXXXXX] XXXXXXXX: eight-digit wireless code Example:Set wireless encoding as Operating method:[8] [6] [ ] 13.5 Wireless smart appliance control To enter the wireless coding and timing arm and disarm settings, voice prompts, press [7] on the keyboard, voice prompts: Please enter an eight-digit wireless address code. The wireless encoding of eight digits is only from 0-2.The last voice prompt: Setting completed. Setting method:[8] [7] [XXXXXXXX] XXXXXXXX:Eight-digit wireless code Example:Set wireless equipment encoding as Operating method:[8] [7] [ ] 14. History query Enter the settings according to the main menu after the voice prompt, press [9] to enter the history query. Then you will continue to hear the following voice: Press 2 to inquiry next message; Press 8 to inquiry former message; Press * to return previous menu; Press # for replay. Host enters history inquiries, press [2] to downturn, press the [8] to upturn. Setting method:[9] 15. Host state 12

13 Under normal circumstances, usually only the following four states: 1) Arm state: armed,the02to99zonealarm. 2) Home arm state: armed, the settings for [home arm] are effective zone alarm. 3) Disarm state: disarmed, the 02 to 99 zone alarm (24 hours zone excluded). 4) Set state: when set it, all zones are not the police. 16. Day-to-day operations The remote control is carried out a variety of functional operation of a device by radio, alarm host. The role is to facilitate the users outside the door (households) or distant alarm, operate for out arm, home arm, SOS alarm, and disarm immediately. 1) Out arm: Press [ ] key, the host is armed immediately alert. 2) Disarm operation: Press the [ ] key, the host is in disarming standby state immediately. 3) Home Arm: Press [ ] key, is at home (staying) alarm alert. 4) SOS alarm: Press [ ] key, the host immediately trigger an emergency alarm 17. Out arm Out arm: the alarm host all alert arming: no one at home, you need to prevent on-site comprehensive alarm detection alert, all detectors are in working condition; triggered when the probe source (thief intrusion, fire, gas leak, etc.)the detectors, alarm system alarm immediately. If host keyboard lock is off, press the host keyboard [OUT ] key, it will in AWAY state; if the host keypad lock is on, press the host keyboard [OUT ] key, and then need to enter the user password to enter the system external arming state. Remote control operation: Press the remote control [OUT ] key once. Host operation: [OUT ] (keypad lock off) or [OUT ] + user password + # (keyboard lock on) SMS instructions: [user password] + ARM 18. Home arm Home arm (staying): the alarm host is part of the alert arm: someone at home, for safety reasons, you need to be part of the detector in the home (such as doors, windows, balconies, boundary alarm etc.) in a state of alert; another part of the detector (e.g.: hall and other masters of their own trigger to cause false alarm) in non-state of alert, then select home arm. Note: home arm only realize by a remote control to operate. Remote control operation: Press the remote control [ ] key once. Host operation: press home arm [ ] on the keyboard 19. Host disarm Hosts disarm: it is in a non-alert state. One: after arming operation, the normal disarm; another: after host alarm need stop this alarm, is also disarmed, normal zone will not work after disarm operation, except for 24-hour zones. The host keyboard lock is off, you want to disarm, Press disarm buttons directly on the host[ ]can be realized disarm; if the host keyboard lock is turned on, you will need to press[ ], then enter user password according to voice prompts, plus [#] key. [Away] or [Home arm] indicator light goes out. Disarm operation is successful. Remote control operation: Press the[ ]button. Host operating: [disarm] (keyboard lock off) or [disarm ] + [user password] + [# (keyboard lock on) ] SMS instructions: [user password] + DISARM 13

14 20. Answer the alarm Once the alarm host alarm, alarm beep sound immediately; First dial the default phone (mobile phone) voice alarm automatically. If the phone unanswered, the host will be automatically transferred to the next set of calls, all preset phone numbers of each cycle dial 9 times. If the dial telephone answers, the handset first heard the alarm zone information and alarm location, and then plays 10 seconds of recoding information. Recording will continue to play after playing remote operation tone: Press 1 to arm, press 2 to disarm, press 3 to monitor, press 4 to talk, press 5 to close monitor, press 6 sirens on, press 7 siren off, press 8 to turn on the wireless electrical appliances control, press 9 to turn off electrical appliances control. At the same time, press the keys of the keyboard of the phone (mobile phone), you can achieve different functions: Direct hook: and no one answered the host cycle to dial all phone 9. Hang up directly: and no one answered, the host cycle to dial all phone 9 times. Press [1]: the host into the arm state, the earpiece voice prompts: armed. Press [2]: the host into disarm state, earpiece voice prompt: disarmed. " Press [3]: the host into the monitor for 30 seconds, if continue monitoring, press [3] key repeatedly delay of 30 seconds. Press [4]: start the scene 30 seconds intercom function. Press [5]: close monitoring function. Press [6]: turn on the siren. Press [7]: turn off the siren. Press [8]: turn on the wireless appliance control. Press [9]: turn off the wireless appliance control. 21. Remote control Via phone (mobile phone) call the phone number connected with alarm host, set the number of rings after the handset to hear "Please input password" tone. In this case, enter the password; password is correct, the earpiece sent prompt Press 1 to arm, press 2 to disarm, press 3 to monitor, press 4 to talk, press 5 to close monitor, press 6 sirens on, press 7 siren off, press 8 to turn on the wireless electrical appliances control, press 9 to turn off electrical appliances control ; Password error,the earpiece sent prompt Password is incorrect, please re-enter After entering the remote control operation via the telephone keypad remote control: Press [1]: the host into the arm state, the earpiece voice prompts: armed. Press [2]: the host into disarm state, earpiece voice prompt: disarmed. " Press [3]: the host into the monitor for 30 seconds, if continue monitoring, press [3] key repeatedly delay of 30 seconds. Press [4]: start the scene 30 seconds intercom function. Press [5]: close monitoring function. Press [6]: turn on the siren. Press [7]: turnoffthesiren Press [8]: turn on the wireless appliance control. Press [9]: turn off the wireless appliance control 22. SMS remote control Control the control panel by SMS instruction to arm, disarm and make the siren turn on or off. The detailed SMS instruction: For Arm: [User password] + ARM. Example: 1234ARM. If you got the message of arm after sent the message, said that the home alarm system is in the arm status. For Disarm: [user password] + DISARM. Example: 1234DISARM. If you got the message of disarm after sent the message, said that the home alarm system is in the disarm status. For turning on the siren: [user password] + ONSIREN. Example: 1234ONSIREN. If you got the message of siren is on, said that the siren is ringing. For turning off the siren: [user password] +OFFSIREN. Example: 14

15 1234OFFSIREN. If you got the message of siren is off, said that the ring of siren is closed. 23. SOS Sometimes, at home occur in some special cases: the elderly or children sudden illness, requiring emergency; suddenly caught fire in the home, they need for help; criminals burglary, mugging, must call 110. At this time, simply press the host [ ] emergency key, remote control of the [ ] key, wireless emergency button. Alarm system immediately alarm and automatically call for alarm. Remote control operation: Press the [ ] button. Host operating: host keyboard [ ] emergency button 24. additional function the home alarm system will send the SMS message of abnormal conditions include low power, AC power broken and AC power recover automatically. So customers could know the working condition of the home alarm system timely. [Maintenance] 1. System detection Alarm system are in use every day, but must also conduct regular maintenance, periodic testing, in order to ensure the alarm system is stable, reliable, safe operation. Usually, alarm host must be comprehensive detection every three months, detectors test monthly. Even no conditions you should test them every three months. Host detection: 1. host arm /disarm normally or not. 2. The host alarm whether normal outgoing calls 3.Normal receiver detector signal or battery backup is normal. Probe detection: 1. Trigger detectors by hand, check whether alarm normally. 2.Check the batteries in all detectors, see if under voltage. 3. Test launch of wireless detectors, to see whether it can communicate with the host. 2. Note Do not dismantle, repair and renovation products, otherwise there will be likely to cause accidents and malfunctions. Do not use this product has been dropped on the ground or a hard object, avoid strong impact, resulting in failure and damage. Without the relevant permit and consent, do not directly set to the "110", "119" or the police station alarm phone alarm calls of the host. 3. Technical Parameters Schedule Table one: Technical Parameter Input power: DC12V 500mA Standby power consumption : 66mA Alarm current: Max 650mA Output current: DC12V 300mA GSM mode Quad-band850/900/1800/1900MHz Radio frequency: 315MHz/433MHz Encoding: 2262 IC / 4.7MΩ Alarm sound: 110dB Back-up battery: AAA 7.2V Clock battery: Zn/Ago battery3.0v Suitable temperature: -20 ~+55 15

16 Suitable humidity: 40% ~ 80% two: instruction setting Number First-level menu Second-level menu Instruction Remark Factory fault Engineer password setting 1+1+XXXX XXXX=a 4-digit engineer password setting 6666 Password and User password setting 1+2+YYYY YYYY= a 4-digit user password setting 1234 system time system time setting 1+3+AA+BB+CC AA=year,BB=month, CC=date 1 setting system time setting 1+4+DD+EE DD=hour,EE=minute Table 2 Voice alarm telephone setting and deleting 3 4 Remote control code /Detector code matched and deleted System function options settings 1~6 alarm phone setting 2+X+1+YYYY+# X=1~6 group telephone number YYYY=alarm telephone number 1~6 delete alarm code 2+X+2 X=1~6 group telephone number 1~2 SMS number setting 2+X+YYYY+# X=7~8(1~2 group SMS number) YYYY=SMS number 1~2 delete SMS code 2+X+2 X=7~8(1~2 group SMS number) Remote control code 3+1 Detector code 3+2+XX XX=defense zone number Delete remote control code 3+3 Delete single detector code 3+4+XX XX= defense zone number Delete all detector code 3+5 Phone line broken alarm setting 4+1+X X=1 turn on X=0 turn off 0 Tone of arming or disarming 4+2+X X=1 turn on X=0 turn off setting Siren ring time setting 4+3+XX XX=delay time 00~15 minutes 3 minutes arm delay time setting 4+4+XX XX=delay time 00~99 seconds Alarm delay time setting 4+5+XX XX=delay time 00~99 seconds Phone alarm number of cycles 4+6+XX XX=00~15 times 9 times Times of rings 4+7+X X=0~9 times 6 times Keyboard password protection 4+8+X X=1 turn on X=0 turn off 1 Record setting 4+9 Play recoding automatically after recoding 16

17 17

18 Network alarm settings Alarm type set Zone type setting The wireless coding and timing arm and disarm settings Set the first and second groups of center number Delete the first and second groups of center number 5+X+1+YYYYY+# X=1~2 group YYYYY=telephone number 5+X+2 18 X=1~2 group User ID setting 5+3+XXXX XXXX= 4-digit user password Arm and disarm the Upload Settings 5+4+X X=1 turn on X=0 turn off Alarm type set 6+XX+Y+# 02~99:02~99 defense number, X=0: Bypass defense zones X=1:Real-time defense zone, X=2:Stay at home defense zone, X=3:24-hour defense zone Zone type setting 7+XX+Y 02~99:02~99 zones number X=1: SOS alarm X=2: fire alarm X=3: gas leaks alarm X=4:window alarm X=5:balcony alarm X=6:hall alarm X=7:door alarm X=8:boundary alarm First / second group of time arm 8+X(1~2)+AA+BB X: First / second group of time arm set AA: Hour (24hours) BB: Minute First / second group of time 8+X(3~4)+AA+BB X:First / second group of time disarm disarm set AA: Hour (24hours) BB: Minute Timing arm and disarm switch 8+5+X X=1 turn on settings X=0 turn off Wireless siren coding settings 8+6+XXXXXXXXX XXXXXXXX=8 is wireless coding Wireless smart appliance 8+7+XXXXXXXXX XXXXXXXX=8 is wireless coding control 9 History query History query 9 press [2] to downturn, press the [8] to upturn Instant defense zones

19 19

Contents 目 录. Preface] [Function Introduction]

Contents 目 录. Preface] [Function Introduction] Contents 目 录 Preface] Thank you for choosing the wireless alarm system product of our company. Wireless alarm system adopts the most advanced digital sensing and controlling technologies, it is the intelligent

More information

MOBILE CALL GSM alarm system

MOBILE CALL GSM alarm system MOBILE CALL GSM alarm system User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. - 1 - Catalogue: Function Introduction 2 SMS Number

More information

MOBILE CALL GSM Alarm System User s Manual

MOBILE CALL GSM Alarm System User s Manual MOBILE CALL GSM Alarm System User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Contents Function Introduction Alarm Host Diagram

More information

Intelligent GSM Auto-Dial Alarm System

Intelligent GSM Auto-Dial Alarm System Auto-dial Alarm System Intelligent GSM Auto-Dial Alarm System Profile For a better understanding of this product, please read this user manual thoroughly before using it. 2013.2.V1.0 Auto-dial Alarm System

More information

Security GSM Alarm System

Security GSM Alarm System KONLEN TECHNOLOGY LIMITED Website: www.konlen.com Add:, 3/F, Building5, Kaijieda Industry Zone, Huachang Road, Longhua, Shenzhen China Tel: +86-(0)755-29709632 E-mail: konlensales@126.com klarm@konlen.com

More information

Intelligent Wireless GSM Alarm System

Intelligent Wireless GSM Alarm System Wireless GSM Alarm System Intelligent Wireless GSM Alarm System Profile For a better understanding of this product, please read this user manual thoroughly before using it. 2013.3.V1.0 Wireless GSM Alarm

More information

New GSM Alarm System. User s Manual. Profile For a better understanding of this product, please read this user manual thoroughly before using it.

New GSM Alarm System. User s Manual. Profile For a better understanding of this product, please read this user manual thoroughly before using it. New GSM Alarm System User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Chapter 1. Features Chapter 2. Alarm Host Introduction Chapter

More information

GSM Alarm System User Manual

GSM Alarm System User Manual GSM Alarm System User Manual For a better understanding of this product, please read this user manual thoroughly before using it. Quick Guider After getting this alarm system, you need to do the following

More information

Home Alarm System User s Manual. Home Alarm System User Manual

Home Alarm System User s Manual. Home Alarm System User Manual Home Alarm System User s Manual Home Alarm System User Manual Dear Clients, Thank you for using our GSM Alarm System. We are committed to giving you the best home security available today and take the

More information

MOBILE CALL GSM Alarm System

MOBILE CALL GSM Alarm System Auto-dial Alarm System MOBILE CALL GSM Alarm System Profile For a better understanding of this product, please read this user manual thoroughly before using it. 2012.11.V2.0 Auto-dial Alarm System CONTENTS

More information

Wolf Guard GSM Wireless alarm system User s Manual

Wolf Guard GSM Wireless alarm system User s Manual Wolf Guard GSM Wireless alarm system User s Manual Page 1 Warning Do not remove the front or back cover of the unit and keep it intact. There are no parts inside this unit that can be repaired or replaced

More information

GSM Home Alarm System User Manual. http://www.usmartbuy.com

GSM Home Alarm System User Manual. http://www.usmartbuy.com GSM Home Alarm System User Manual http://www.usmartbuy.com 1 1. Factory default Normally, all sensors in the big box have been coded (learnt) to the control host Operation Password: 0000 Long-Distance

More information

Two-way communication, keep checking the commnunication between the panel and accessories, make sure the system safer.

Two-way communication, keep checking the commnunication between the panel and accessories, make sure the system safer. Innovative GSM & WIFI dual network operating platform. On WIFI network, the alarm system will work without any fee. If no WIFI, it will work on GSM automatically. With state-of-the-art WIFI network technology,

More information

GSM Alarm. An Advanced Programmable Multifunctional GSM Auto Dialer GSM Alarm Panel In The Worldwide! User Manual. S100Pro. Ver 1.

GSM Alarm. An Advanced Programmable Multifunctional GSM Auto Dialer GSM Alarm Panel In The Worldwide! User Manual. S100Pro. Ver 1. An Advanced Programmable Multifunctional GSM Auto Dialer GSM Alarm Panel In The Worldwide! GSM Alarm User Manual S100Pro Ver 1.0 Date Issued: 2013-09-01 All rights reserved by King Pigeon Hi-Tech.Co.,Ltd.

More information

Wireless AUTODIAL GSM SMS Home Alarm Security System 900/ 1800/ 1900Mhz(CK-GSM-9003)

Wireless AUTODIAL GSM SMS Home Alarm Security System 900/ 1800/ 1900Mhz(CK-GSM-9003) CN2HK LIMITED Wireless AUTODIAL GSM SMS Home Alarm Security System 900/ 1800/ 1900Mhz(CK-GSM-9003) User Manual Please read this manual before operating this product. After you finish reading this manual,

More information

LCD -based Intelligent Burglar Alarm System. User Guide. Ver 2.0

LCD -based Intelligent Burglar Alarm System. User Guide. Ver 2.0 LCD -based Intelligent Burglar Alarm System User Guide Ver 2.0 Table of Content 1. Introduction... 2 1.1 General Description... 3 1.2 System Features... 3 2. Anatomy of the LCD-based Intelligence Burglar

More information

PiSector Professional. Wireless GSM Alarm System

PiSector Professional. Wireless GSM Alarm System PiSector Professional Wireless GSM Alarm System User Manual (GSM-03) Read manual fully before use. PiSector Inc., USA, www.pisector.com 1. WHAT'S IN THE BOX... 4 2. MAIN FEATURES... 5 3. KNOW YOUR SYSTEM...

More information

GSM INTRUSION ALARM SYSTEM INSTRUCTION MANUAL. GSM - PSTN - SMS - TOUCH GSM Wireless Security Alarm System

GSM INTRUSION ALARM SYSTEM INSTRUCTION MANUAL. GSM - PSTN - SMS - TOUCH GSM Wireless Security Alarm System GSM INTRUSION ALARM SYSTEM INSTRUCTION MANUAL GSM - PSTN - SMS - TOUCH GSM Wireless Security Alarm System SECURE YOUR HOME AND BUSINESS Printed in Shenzhen RE: G60-GSM-August-2013 Key Features Smart touch

More information

S100. GSM House Alarm System. Http://www.GSMalarmsystem.com

S100. GSM House Alarm System. Http://www.GSMalarmsystem.com S100 GSM House Alarm System Http://www.GSMalarmsystem.com 1. Brief introduction The GSM Alarm System is a new security protection solution special for home, house and office and other applications. It

More information

User Manual GSM Alarm System. www.deltasecurity.cn. All rights reserved by Delta Security Co., Ltd

User Manual GSM Alarm System. www.deltasecurity.cn. All rights reserved by Delta Security Co., Ltd User Manual GSM Alarm System All rights reserved by Delta Security Co., Ltd Dear Clients, Thank you for using our GSM Alarm System. We are committed to giving you the best home security available today

More information

Intruder Alarm System

Intruder Alarm System Intruder Alarm System GSM & PSTN Wireless and Wired Touch Model 2013-01 V1.0.0 Statment This equipment must be installed and used in strict accordance with the instructions given in this user documentation.

More information

DC-8706K Auto Dial Alarm System

DC-8706K Auto Dial Alarm System DC-8706K Auto Dial Alarm System User Guide Basic Contents: 1x the host unit; 1x wireless door (window) magnet; 1x wireless infrared detector; 2x remote control; 1x siren; 1x phone core; 1x AC to DC power

More information

Dual-Network LCD Keyboard Intelligent Alarm. User Guide

Dual-Network LCD Keyboard Intelligent Alarm. User Guide Dual-Network LCD Keyboard Intelligent Alarm User Guide Ver 2.0 Version 2.0 Page 1 of 38 Table of Content 1. Introduction... 3 1.1 General Description... 3 1.2 System Features... 3 2. Anatomy of the LCD

More information

PSTN Home Alarm System

PSTN Home Alarm System PSTN Home Alarm System User Manual Model: PST-TEL99E Please read this user guide carefully before operation and installation. Contents 1. Product Overview... - 3-2. Main Function & Features... - 3-3. For

More information

Six-defense zone Display Alarm System. User Manual

Six-defense zone Display Alarm System. User Manual Six-defense zone Display Alarm System User Manual Feature 1. Anti-interfere function. When someone interferes it with same frequency, the control unit will activate siren to alarm. 2. Support anti-decode

More information

Home alarm system. User s manual. Profile To better understand this product, please read the user s manual carefully before using.

Home alarm system. User s manual. Profile To better understand this product, please read the user s manual carefully before using. Home alarm system User s manual Profile To better understand this product, please read the user s manual carefully before using. Features; 1. 1-99 LED wireless defense zone, with digital number to show

More information

GSM Home Alarm system. User Guide

GSM Home Alarm system. User Guide GSM Home Alarm system User Guide Version 2.0 Page 1 of 21 TABLE OF CONTENT System Overview...3 Introduction...3 Features...3 About the Front Panel...4 About the Back Panel...5 General Operation...6 AWAY

More information

GSM ALARM SYSTEM USER MANUAL

GSM ALARM SYSTEM USER MANUAL GSM ALARM SYSTEM USER MANUAL 1. Instruction The alarm system is based on GSM network. With a GSM SIM card, it can be used wherever you want and no need to connect any wire, which is convenient and easy

More information

LW-2000-3A. Wireless Auto Dial Alarm System. Sentry Plus User Manual By Global Gadgets

LW-2000-3A. Wireless Auto Dial Alarm System. Sentry Plus User Manual By Global Gadgets LW-2000-3A Wireless Auto Dial Alarm System Sentry Plus User Manual By Global Gadgets Main Features Simple to use keypad for operation and control. The system can store up to 9 telephone numbers: positions

More information

GSM&PSTN Dual-Network Burglar Alarm System

GSM&PSTN Dual-Network Burglar Alarm System GSM&PSTN Dual-Network Burglar Alarm System (KR-5800G) User Guide Version 2.0 Version 2.0 Page 1 of 38 Table of Content 1. Introduction... 3 1.1 General Description...3 1.2 System Features...3 2. Anatomy

More information

Security GSM Alarm System USER MANUAL

Security GSM Alarm System USER MANUAL Security GSM Alarm System USER MANUAL System installation Brief introduction of system This alarm consists of main engine of alarm and various wireless-connected accessories. When people enter the defense

More information

STATUS POWER MONITOR ALARM SOS DISARM

STATUS POWER MONITOR ALARM SOS DISARM STATUS POWER MONITOR ALARM SOS DISARM I. Features II. Preparation before use III. Host 1.LED status explanation 2. Host panel IV. System Settings 1. Coding of wireless sensors 2. Exit coding 3. Settings

More information

Iphone & Android App Smart GSM Home Alarm System

Iphone & Android App Smart GSM Home Alarm System Iphone & Android App Smart GSM Home Alarm System PST-GA242Q User Guide Version V14.3 Dear User, Thanks for selecting the intelligent alarm system. Please read through this guide before installation so

More information

Business/ Home GSM Alarm System

Business/ Home GSM Alarm System Business/ Home GSM Alarm System BUSINESS/HOME GSM ALARM SYSTEM POWER STATUS RECORD SIGNAL User Manual Profile For a better understanding of this product, please read this user manual thoroughly before

More information

Home Security Alarm System

Home Security Alarm System Home Security Alarm System User Manual (ALM-S02) Read manual carefully before use. PiSector Inc., USA www.pisector.com Thank you for purchasing this home security alarm system. For your safety and better

More information

HomeSafe-Basic VT-PS99E. User s Manual. PSTN Home Alarm System. Page: 1 / 15

HomeSafe-Basic VT-PS99E. User s Manual. PSTN Home Alarm System. Page: 1 / 15 HomeSafe-Basic VT-PS99E User s Manual PSTN Home Alarm System Page: 1 / 15 Table of Contents 1. Product Overview:... 3 2. Main Functions & Features... 3 3. For Your Safety... 4 4. VT-PS99E Characteristics...

More information

Business/Home GSM Alarm System. Installation and User Manual

Business/Home GSM Alarm System. Installation and User Manual Business/Home GSM Alarm System Installation and User Manual Brief Introduction: GSM 900/1800/1900 bands, can be used in most parts of the world Full duplex communication with the host Monitor the scene

More information

Wireless Auto-dial Intruder Alarm System

Wireless Auto-dial Intruder Alarm System Wireless Auto-dial Intruder Alarm System User Manual User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Features and Function 1.

More information

Intelligent Alarm System

Intelligent Alarm System Intelligent Alarm System User Manual Ver 12-3 Dear users, Thank you for having selected the intelligent alarm system. Please read through this manual before installation so as to operate properly. The

More information

PROFESSIONAL HOME ALARM SYSTEM. Important! Please read these instructions carefully.

PROFESSIONAL HOME ALARM SYSTEM. Important! Please read these instructions carefully. WIRELESS AUTODIAL HOME ALARM SYSTEM AM2000 Instructions for use Important! Please read these instructions carefully. IMPORTANT 1 IDENTIFICATION PLEASE CONTACT BEFORE RETURNING THIS PRODUCT TO THE RETAILER

More information

Using your LED Plus keypad

Using your LED Plus keypad Using your LED Plus keypad System 238 System 2316 System 238i System 2316i Part Number 5-051-372-00 Rev B Thank you for purchasing this C&K alarm system Your system is one of the most powerful and advanced

More information

Intelligent GSM Auto-dial Alarm System User s Manual

Intelligent GSM Auto-dial Alarm System User s Manual Intelligent GSM Auto-dial Alarm System User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. [Function Instruction] [Control Panel Introduction]

More information

WITURA CORPORATION SDN BHD

WITURA CORPORATION SDN BHD WT 1010SA Stand Alone GSM Alarm System User Manual and Installation Instructions Version: 1.2 Updated: 4 JAN 2012 WITURA CORPORATION SDN BHD Stand Alone GSM Alarm System Instruction Manual 1 Introduction:

More information

Solution-16 Operators Manual ISSUE 1.60

Solution-16 Operators Manual ISSUE 1.60 Solution-16 Operators Manual ISSUE 1.60 !"#$%&"'()*+ Operators Manual Copyright 2002 by, SYDNEY, AUSTRALIA Document Part Number MA880O DOCUMENT ISSUE 1.60 Printed 22 March 2002 This documentation is provided

More information

WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER

WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER BAT.LOW AC WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER THE SYSTEM THAT CALLS YOU! Our WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER is designed to allow you to create your own security system.

More information

PiSector Home security systems

PiSector Home security systems PiSector Home security systems User Manual (ALM-S02) Read manual fully before use. PiSector Inc., USA, www.pisector.com Thank you for purchase this alarm system, For proper use and your safety, please

More information

GSM home alarm system s manual

GSM home alarm system s manual GSM home alarm system s manual I. Main features: 1, Eight wireless LED zone, and four wired zone 2, Two-way to communication 3, The system supports the GSM cell phones, no need the fixed telephone line.

More information

WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER

WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER BAT.LOW AC WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER THE SYSTEM THAT CALLS YOU! Our WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER is designed to allow you to create your own security system.

More information

Wireless Home Security System Product Manual (Model #80355)

Wireless Home Security System Product Manual (Model #80355) Wireless Home Security System Product Manual (Model #80355) Installation Instructions During set-up, if no key is pressed for 15 seconds it will come out of the setup mode and you will have to start over.

More information

GSM WIRELESS DIGITAL ALARM SYSTEM USER GUIDE. Please read it carefully before installation and operation

GSM WIRELESS DIGITAL ALARM SYSTEM USER GUIDE. Please read it carefully before installation and operation GSM WIRELESS DIGITAL ALARM SYSTEM USER GUIDE Please read it carefully before installation and operation Your New Diamond Designs Alarm works with a GSM SimCard via the cellular phone,system to call up

More information

TX GSM SMS Auto-dial Alarm System. Installation and User Manual

TX GSM SMS Auto-dial Alarm System. Installation and User Manual TX GSM SMS Auto-dial Alarm System Installation and User Manual Product Features: 1. 16 wireless zones, 3 wired zones alarm system, suitable for small to medium size offices and homes. 2. The system uses

More information

Business/Home GSM Alarm systems. Installation and User Manual

Business/Home GSM Alarm systems. Installation and User Manual Business/Home GSM Alarm systems Installation and User Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Business/Home GSM alarm system

More information

GE Concord 4 Quick User Guide

GE Concord 4 Quick User Guide GE Concord 4 Quick User Guide GE Concord 4 Quick User Guide Page 1 Before Calling Is the keypad beeping? Press *. This will silence the beeping and let you know where the trouble is. Is there a flashing

More information

GSM home alarm system User manual

GSM home alarm system User manual GSM home alarm system User manual 1 Visit our ebay Store http://stores.ebay.com/homepageshop 2 1. System Foreword Wireless GSM intelligent commercial/household guard system employs imported microprocessor

More information

Destiny 4100. Destiny 4100. Owners Manual

Destiny 4100. Destiny 4100. Owners Manual Destiny 4100 Destiny 4100 Owners Manual TABLE OF CONTENTS INTRODUCTION Control Panel...3 Detection Devices...3 Telephone Keypads...3 GLOSSARY... 4-5 LOCAL PHONE ACCESS Using Your Telephones As Keypads...6

More information

DESTINY OWNER S MANUAL

DESTINY OWNER S MANUAL DESTINY OWNER S MANUAL DESTINY You have made a wise decision to protect your family and property with the DESTINY Security System. The DESTINY has been designed to provide you with a maximum level of security

More information

User s Information Guide R1A

User s Information Guide R1A HSC505-R Home Security Controller - User Manual Release R1a Pi HSC505 and Pi HSC505R Home Security Controller User s Information Guide R1A Page 1 QD Dynamics (Pty) Ltd reserves the right to make changes

More information

GSM Voice Auto Dialer& SMS sender JC-999. User Manual

GSM Voice Auto Dialer& SMS sender JC-999. User Manual 1. Description 1.1 Main features GSM Voice Auto Dialer& SMS sender JC-999 User Manual (1) Large LCD display,integrated keypad, human-friendly programming; (2) Support 12 alarm receiving numbers; (3) Triggering

More information

FIRST ALERT INSTRUCTION MANUAL FOR FA 270 KEYPADS SECURITY SYSTEM

FIRST ALERT INSTRUCTION MANUAL FOR FA 270 KEYPADS SECURITY SYSTEM FIRST ALERT INSTRUCTION MANUAL FOR FA 270 KEYPADS SECURITY SYSTEM Page 0 Table of Contents Introduction 1 System Basics.. 1 Burglary Protection.. 1 Fire Protection.. 1 Security Codes. 1 Zones and Partitions

More information

Ademco Vista-20P/First Alert FA-168C Basic Commands

Ademco Vista-20P/First Alert FA-168C Basic Commands Zones 64 total Ademco Vista-20P/First Alert FA-168C Basic Commands Wireless Yes, Zones 09 to 48 + 16 Keyfob Zones (Zones 49 to 64) Batteries Downloadable Partitions 2 12 volt Rechargable inside main Panel,

More information

GSM ALARM SYSTEM. Model: G11 USER MANUAL. Ver.: SA

GSM ALARM SYSTEM. Model: G11 USER MANUAL. Ver.: SA GSM ALARM SYSTEM Model: G11 USER MANUAL Ver.: SA0903003 Contents 1. Instruction 1.1 Packing List 1.2 Optional wired & wireless accessories 1.3 Optional sirens 1.4 Specification 2. Main panel description

More information

AGRI-ALERT 800T / AGRI-ALERT 800 ALARM SYSTEM USER MANUAL

AGRI-ALERT 800T / AGRI-ALERT 800 ALARM SYSTEM USER MANUAL AGRI-ALERT 800T / AGRI-ALERT 800 ALARM SYSTEM USER MANUAL Manufacturer: Viatron Electronics 3514 1st Street, St-Hubert (Quebec) Canada J3Y 8Y5 WARNING: the warranty can be void if the Agri-Alert 800T or

More information

Wireless Spot Alarm System

Wireless Spot Alarm System Wireless Spot Alarm System For a better understanding of this product, please read this user manual thoroughly before using it. This wireless alarm system, include a light and sound function, convenient

More information

Emergency Dialer DIAL-ALERT MODEL: AD-105. www.skylinkhome.com

Emergency Dialer DIAL-ALERT MODEL: AD-105. www.skylinkhome.com www.skylinkhome.com Emergency Dialer TM DIAL-ALERT MODEL: AD-105 If you would like to order Skylink s products or have difficulty getting them to work or download information and user manual, please :

More information

Control/Communicator Installation Manual

Control/Communicator Installation Manual DAS NETWORX NX-8 Control/Communicator Installation Manual Page General Description... 2 Ordering Information... 2 Option Definitions... 2 Programming the LED Code Pads... 4 Programming the NX-8... 8 Types

More information

1pcs. 1pcs. 2pcs 1pcs 1pcs 2pcs

1pcs. 1pcs. 2pcs 1pcs 1pcs 2pcs Home security alarm system LX-HS06 Instruction Brief introduction LX-HS06 is a set of entirely new English home security alarm system, it uses advanced MCU control and SMD technology. it innovate multiple

More information

GSM House Alarm System. S110 User Manual. Ver 1.00 Date Issued: 2010-09-01

GSM House Alarm System. S110 User Manual. Ver 1.00 Date Issued: 2010-09-01 GSM House Alarm System S110 User Manual Ver 1.00 Date Issued: 2010-09-01 All rights reserved by King Pigeon Hi-Tech. Co., Ltd. Website: Http://www.GSMalarmsystem.com Table of Contents 1. Brief introduction

More information

NetworX NX-6V2. LED Keypad User Manual

NetworX NX-6V2. LED Keypad User Manual NetworX NX-6V2 LED Keypad User Manual POWER Light is on when AC power is present; flashes to indicate a low battery condition. ARMED Light is on when armed; off when disarmed; flashes to indicate a previous

More information

SCORPION Z16040C Alarm Controller User Instructions

SCORPION Z16040C Alarm Controller User Instructions SCORPION Z16040C Alarm Controller User Instructions Thank you for choosing to purchase this micron security alarm controller. Micron product is manufactured to exacting quality standards. We understand

More information

Using Your. Security System With Icon Keypad S5020, S5021, S5022

Using Your. Security System With Icon Keypad S5020, S5021, S5022 Using Your Security System With Icon Keypad S5020, S5021, S5022 Contents 1 Overview Your Security System... 1 How Your Security System Works... 2 Your System's Programming... 3 Getting Used to Your System...

More information

SECURITY SYSTEM NOTES

SECURITY SYSTEM NOTES SECURITY SYSTEM NOTES Installing/Service Company For Service Call Central Station Duress Code FUNCTION CODES Function Code Controls Function This system is is not partitioned. EMERGENCY ACTIVATION KEYS

More information

Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2. Instruction Manual

Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2. Instruction Manual Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2 Instruction Manual Firmware version: 2.0.1 Issue: 0.6 Version of the GPRS transmitters configurator: 1.3.6.3 Date of issue: 07.03.2012 TABLE OF CONTENTS

More information

Understanding the Code Pad lights...4. Code Pad tones...5. Fully arming the system On MODE...6. Fully arming the system - Quick Arm MODE...

Understanding the Code Pad lights...4. Code Pad tones...5. Fully arming the system On MODE...6. Fully arming the system - Quick Arm MODE... TABLE OF CONTENTS...Glossary of terms...2...code Pad Diagram...3 Understanding the Code Pad lights...4 Code Pad tones...5 Fully arming the system On MODE...6 Fully arming the system - Quick Arm MODE...6

More information

User's Manual. For use with ProSYS 16, ProSYS 40, and ProSYS 128

User's Manual. For use with ProSYS 16, ProSYS 40, and ProSYS 128 User's Manual For use with ProSYS 16, ProSYS 40, and ProSYS 128 Important Notice This manual is delivered subject to the following conditions and restrictions: This manual contains proprietary information

More information

Voice GSM alarm system user guide

Voice GSM alarm system user guide Voice GSM alarm system user guide System Overview Introduction Wireless GSM Burglar Alarm with voice prompt for commercial and home use is built on leading microprocessor technology with advanced GSM digital

More information

tattletale User Guide Consumer unit version 2.48 1 P a g e

tattletale User Guide Consumer unit version 2.48 1 P a g e tattletale User Guide Consumer unit version 2.48 1 P a g e Contents Basic 1... 4 Base Unit Features... 4 Initial Setup... 4 Arming... 5 Disarming... 5 Quiet Button... 5 Settings... 5 Settings 2... 6 Quick

More information

Using Your. Security System. With LED Keypad S5030, S5031, S5032

Using Your. Security System. With LED Keypad S5030, S5031, S5032 Using Your Security System With LED Keypad S5030, S5031, S5032 Contents 1 Overview Your Security System... 1 How Your Security System Works... 2 Your System's Programming... 3 Getting Used to Your System...

More information

PiSector GSM Cellular Wireless Alarm System

PiSector GSM Cellular Wireless Alarm System PiSector GSM Cellular Wireless Alarm System User Manual ( GS08 ) Read manual fully before use. PiSector Inc., USA, www.pisector.com Welcome to PiSECTOR Thank you for choosing PiSECTOR. Everyone at PiSECTOR

More information

Business/Home. GSM Alarm system

Business/Home. GSM Alarm system Business/Home GSM Alarm system Installation and Users guide Profile For a better understanding of this product, please read this user manual thoroughly before using it. I. General information: GSM 900/1800/1900

More information

Wireless Alarm system s manual

Wireless Alarm system s manual MOUNTVIEW TECH AUSTRALIA PTY LTD Wireless Alarm system s manual ADS A180 Series ADS Security 1/11/2011 1. Before You Begin For your safety and the safety of others, and to ensure that you get the most

More information

IDS. Users Guide to Keypad Functions S E C U R I T Y MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18

IDS. Users Guide to Keypad Functions S E C U R I T Y MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18 INHEP DIGITAL IDS S E C U R I T Y Users Guide to Keypad Functions MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Away Arm Stay

More information

ICP-CC488 ICP-CC488 EN. Control Panel. User s Guide

ICP-CC488 ICP-CC488 EN. Control Panel. User s Guide ICP-CC488 EN User s Guide ICP-CC488 Control Panel ICP-CC488 User's Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems, Inc. ( Bosch

More information

Solution 880 Operators Manual ISSUE 1.10

Solution 880 Operators Manual ISSUE 1.10 Solution 880 Operators Manual ISSUE 1.10 Solution 880 Operators Manual Copyright 2001 by, SYDNEY, AUSTRALIA Document Part Number MA408O DOCUMENT ISSUE 1.10 Printed 25 May 2001 This documentation is provided

More information

Quick Installation Guide LCD GSM ALARM SYSTEM LH http://www.usmartbuy.com

Quick Installation Guide LCD GSM ALARM SYSTEM LH http://www.usmartbuy.com A. Manipulation Specification Quick Installation Guide 1. Arming Arming means all-around guarded when there is no person at home. All detectors are working. Once something triggers any of the detectors,

More information

Security module CG2 User manual

Security module CG2 User manual Security module CG2 User manual TRIKDIS, JSC Draugystes str. 17, LT-51229 Kaunas LITHUANIA E-mail info@trikdis.lt Web http://www.trikdis.lt This manual is furnished to help You understand Your security

More information

Auto Dialer. Manual E-921APQ E-921GPQ

Auto Dialer. Manual E-921APQ E-921GPQ Troubleshooting: Auto dialer will not arm/disarm Auto dialer will not dial out Unit doesn t respond to a call-back Difficulty in activating room monitor by telephone remote control Make sure that you have

More information

Business/Home GSM. Alarm System(III) Installation and Users guide

Business/Home GSM. Alarm System(III) Installation and Users guide Business/Home GSM Alarm System(III) Installation and Users guide I. General information: GSM 900/1800/1900 bands, can be used all over the world. Full duplex communication with the base. Monitor environment

More information

GSM Alarm System. Installation and Users guide. 1. One-zone alarm system, suitable for office, home, boat and caravan.

GSM Alarm System. Installation and Users guide. 1. One-zone alarm system, suitable for office, home, boat and caravan. GSM Alarm System Installation and Users guide General Information: 1. One-zone alarm system, suitable for office, home, boat and caravan. 2. Alarm system uses a GSM communicator, no distance limits to

More information

GUIDE GETTING STARTED IMPORTANT SUPPORT RESOURCES

GUIDE GETTING STARTED IMPORTANT SUPPORT RESOURCES IMPORTANT SUPPORT RESOURCES Subscriber Portal Go to https://portal.coxhomelife.com to log in to your account and manage your system features online. Online Support Go to www.cox.com/homelifesupport to

More information

IDS X-Series User Manual 700-398-01D Issued July 2012

IDS X-Series User Manual 700-398-01D Issued July 2012 1 2 Contents 1. Introduction to the IDS X-Series Panels... 7 2. Before Operating Your Alarm System... 7 3. Understanding the Keypad LEDs... 8 3.1 Viewing Data on an LED Keypad... 12 3.1.1 LED Status Indicators...

More information

Elite 8D/Lite Version 8 Zone Controller. Arrowhead Alarm Products Ltd. Operating Guide. Proudly Designed and Manufactured in New Zealand

Elite 8D/Lite Version 8 Zone Controller. Arrowhead Alarm Products Ltd. Operating Guide. Proudly Designed and Manufactured in New Zealand Elite 8D/Lite Version 8 Zone Controller 8 Arrowhead Alarm Products Ltd Operating Guide 1 Proudly Designed and Manufactured in New Zealand 2 CONTENTS Page No. INTRODUCTION 4 About your Alarm 4 OPERATING

More information

GSM SMS Controller GSM SMS Alarm Unit S130 S140 S150. User Manual

GSM SMS Controller GSM SMS Alarm Unit S130 S140 S150. User Manual Remote switching machines with a SMS text from your mobile phone! Remote Monitoring your assets in the worldwide by your mobile Phone! GSM SMS Controller GSM SMS Alarm Unit S130 S140 S150 User Manual Ver

More information

Additional Instruction

Additional Instruction Additional Instruction Note: a. Please connect the camera with 2.4G WIFI router or Ethernet cable, can t support 5G router. b. For first time wifi connection, please put your mobile close to camera within

More information

CONTENTS QUICK SETUP & INSTALLATION USER MANUAL. SUPA8 Quick Setup & User Manual

CONTENTS QUICK SETUP & INSTALLATION USER MANUAL. SUPA8 Quick Setup & User Manual SUPA8 Quick Setup & User Manual QUICK SETUP & INSTALLATION CONTENTS FACTORY DEFAULTS... 1 INSTALLATION OF THE SECURITY SYSTEM... 2 COMMISSIONING THE DIALLER PANEL... 5 ZONE INPUT CONNECTIONS... 7 PANEL

More information

Accenta/Optima. User Guide. Servicing Organisation (Installer) name: Telephone Number: Date of Installation: Account Number: Honeywell Security

Accenta/Optima. User Guide. Servicing Organisation (Installer) name: Telephone Number: Date of Installation: Account Number: Honeywell Security Accenta/Optima User Guide ZONE 1 2 3 4 5 6 7 8 9 Chime Omit Prog PA 0 1 2 3 4 5 6 7 8 9 CHIME OMIT RESET PROG SET Accenta + TA PA DAY POWER PA! " # $ % & 0 1 2 3 5 6 7 8 Chime Omit Reset Prog 4 9 Set PA

More information

ABUS WIRELESS ALARM SYSTEM

ABUS WIRELESS ALARM SYSTEM ABUS WIRELESS ALARM SYSTEM These installation instructions are published by Security-Center GmbH & Co. KG, Linker Kreuthweg 5, D-86444 Affing/Mühlhausen. All rights including translation reserved. Reproductions

More information

ICP-CP500. User's Guide ICP-CP500 Codepads

ICP-CP500. User's Guide ICP-CP500 Codepads ICP-CP500 EN User's Guide ICP-CP500 Codepads ICP-CP500 User's Guide 1.0 ICP-CP500 Series Codepads Overview EN 2 1.0 ICP-CP500 Series Codepads Overview The codepad is the communications interface between

More information

PiSector Land Line Auto Dial Professional Wireless Alarm System

PiSector Land Line Auto Dial Professional Wireless Alarm System PiSector Land Line Auto Dial Professional Wireless Alarm System User Manual ( PS03 ) Read manual fully before use. PiSector Inc., USA, www.pisector.com Welcome to PiSECTOR Thank you for choosing PiSECTOR.

More information

I N S T A L L A T I O N M A N U A L

I N S T A L L A T I O N M A N U A L I N S T A L L A T I O N M A N U A L GSM Alarm Security System ST-SK1 Features Box content - GSM transmiter - Supports up to 10 remote controls, 99 wireless accessories and 50 RFID tags - Can store up to

More information

Hills wireless security alarm DIY range

Hills wireless security alarm DIY range Hills wireless security alarm DIY range EASY TO INSTALL DIY system PEACE OF MIND Receive SMS/calls when alarm is armed INTERACTIVE Arm and disarm by SMS or via smartphone app Control your alarm via smart

More information