STRUCTUREDGROUND SYSTEM FOR DATA CENTER GROUNDING

Transcription

1 STRUCTUREDGROUND System for Data Center STRUCTUREDGROUND GROUNDING SYSTEM C ATA O G - PCCB04 Table of Contents INTRODUCTION How to Use This Catalog The Purpose of GROUNDING ROADMAPS Service Entrance Roadmap Data Center Roadmap Data Center Rack (Raised Floor) Telecommunications Room Roadmap Telecommunications Room Rack EQUIPMENT & RACK GROUNDING KITS Features and Benefits PANDUIT STRUCTUREDGROUND System for Data Center Rack Strip to Rack Jumper Kit Jumper Paint Piercing asher Electrostatic Discharge (ESD) Port Kit Retrofit Rack Thread-Forming Screws Screws COMMON BONDING NETORK COMPONENTS BICSI/J-STD-607-A Telecommunications Busbars Telecommunications and Conductor abel Kit Ring Terminal, Vinyl Expanded Insulation Code Conductor, Two-Hole, ong Barrel with indow ug Flex Conductor, Two-Hole, ong Barrel with indow ug Code/Flex Conductor HTAP Kit Code/Flex Conductor HTAP Clear Covers for HTCT HTAPs Clamp, U-Bolt, Bronze Clamp for ater Pipes, Bronze Rod Clamp, Bronze CRIMPING TOOS Hand Operated Plier Type Tool CONTOUR CRIMP Controlled Cycle Die Type, Manual Hydraulic, 4 Ton, Tool Die Type, Battery Powered Hydraulic, 2 Ton, Tool CD-920 Dies TECHNICA INFORMATION PANDUIT STRUCTUREDGROUND System for Data Center Application Standards Specification ayout for Data Center per BICSI TDM Manual, 0th Edition Recommended Sizing of the Telecommunications Backbone (TBB) and Equalizer (GE) per J-STD-607-A Recommended Cable Sizes for Applications Key Terminology INDEX Related Catalogs

2 RUN H TAP HTAP RUN TAP RUN H TAP 2 TAP TAP *AC Panel should be grounded per NEC standards. Enclosure should be grounded per manufacturer s specifications. A typical raised floor includes a multitude of metallic components which are connected together. It is the responsibility of the manufacturer and installer of the raised floor to insure all the raised floor metallic components are bonded which means that they are connected together electrically in accordance with applicable specifications. The PANDUIT / System does not insure required bonding of the raised floor metallic components. For additional sizes and configurations and to see the complete line of PAN-UG Power and Connectors, see the Termination Solutions Catalog SA-TMCB02. RUN H RUN TAP TAP 2 TAP H See page 28 for PANDUIT STRUCTUREDGROUND System for Data Center Application Standards. For more data center grounding information, see For technical assistance in the U.S., call (outside the U.S., see inside back cover for directory) For the complete line of PANDUIT crimping tools and dies, see the Termination Solutions Catalog SA-TMCB02. CG-920 crimp force measurement gauge available, sold separately, see the Termination Solutions Catalog SA-TMCB02. *Makita is a registered trademark of Makita Corporation in the United States. How to Use This Catalog page 4 PANDUIT STRUCTUREDGROUND System for Data Center is a complete, highly reliable line of products to ground your building and network equipment in compliance with BICSI TDM Manual, 0th Edition and J-STD-607-A, TIA-942, IEEE Std 00 (IEEE Emerald Book), U and CSA Telecommunications Room (see roadmap on page 8) Data Center (see roadmap on page 6) Service Entrance (see roadmap on page 5) pages 5-9 Data Center Roadmap 4 Data Center Rack (Raised Floor) Complies with BICSI TDM Manual, 0th Edition and J-STD-607-A, TIA-942, IEEE Std 00 (IEEE Emerald Book), U and CSA screws are recommended to mount all panels, equipment, shelves, etc. to ensure electrical continuity between metallic components and the grounded rack Can be used to ground equipment mounted in cabinets which meet EIA-0-D; installer should bond all cabinet members Back of Rack Shown to the rack grounding strip Back of Racks Shown Data Racks 4 STRUCTUREDGROUND STRUCTUREDGROUND System for SYSTEM Data FOR Center DATA CENTER GROUNDING Paint Piercing asher Kit: RG (see page ) Screws are used to mount patch panels to the front of the rack: RGTBS (see page 4) 5 Jumper Kit 24", 90 Bent: RGEJ (see page 2) AC Panel* Telecommunications Backbone (TBB) Conduit Building Steel 2 Electrostatic Discharge (ESD) Port Kit recommended for use on front and back of rack: RGESD (see page ) Rack Strip Kit: RGS (see page ) Jumper Kit 6", 90 Bent: RGEJ (see page 2) Raised Floor Pedestal 2 6 Copper Compression HTAP and Telecommunications Clear Cover: HTC 4 Busbar (TGB) and Busbar abel (see page 9) (see page 5) Bronze, U-Bolt Clamp: GP Telecommunications and 2 (see page 22) 5 Conductor abel Kit: TYK (see page 5) Copper Compression, Two-Hole, ong Barrel with indow ug: CC- (see pages 6-7) Jumper Kit 24", 45 Bent: RGEJ (see page 2) to Rack Jumper Kit: RGCBNJ (see page ) typically #2 AG bare copper code conductor is used underfloor 7 Detailed Product pages -2 Code/Flex Conductor HTAP For Making Parallel and Multiple Tap Connections on Code and Flex Conductors Used to tap into continuous conductors as a Tap grooves are separated from one another splice or pigtailing allowing them to function independently so Each HTAP terminates a wide range of HTAP can be used with a single or multiple conductor sizes and combinations of code taps providing maximum design and and flex conductors Class G, H, I and installation flexibility ocomotive to suit a variety of applications Color coded and marked with PANDUIT die Slotted design allows quick and easy index numbers for proper crimp die selection assembly of conductor to HTAP using Requires crimping tools and dies, see pages PANDUIT 94 V-0 cable ties included 25, 26 and 27 U isted and CSA Certified for applications up to 600V when crimped with PANDUIT and specified competitor crimping tools and PANDUIT crimping dies Tin plated to inhibit corrosion Detailed Tool pages Die Type, Battery Powered Hydraulic, 2 Ton, Tool Two stage rapid advance hydraulic system minimizes Tool provided with two, high capacity 2 VDC rechargeable cycle time nickel-metal hydride batteries provides for continuous Provides U isted and CSA Certified connections on operation and eliminates "memory" build-up, one hour PANDUIT PAN-UG copper and aluminum lugs and charge time splices and copper taps Eight second crimp cycle time provides quick terminations, Open "C-Head" design allows easy loading of crimping saves time dies and connectors, saves time Uses industry standard Makita* batteries and charger Rubber boot on crimp head provides abrasion protection industry proven reliability easy to obtain from local retail sources Ram automatically retracts when crimp cycle is complete Requires crimping dies, see page 27 Dies installed using spring loaded die retention pins no need for tools Crimp head rotates 60 degrees provides versatility for use in restricted spaces Part Description CT-29 Terminates PANDUIT PAN-UG Compression Connectors: HTCT6-6 HTCT2-2 HTCT250-2 HTCT Figure Copper Conductor Size Range Dimensions (In.) ire ire PANDUIT PANDUIT Strip Strand Die Color ength Type Run Tap Tap 2 Tap H Tool & Die No. (In.) Copper compression lugs and splices for #8 AG 750 kcmil code conductor Copper compression lugs and splices for #8 AG 600 kcmil flex conductor Copper compression CTAPF taps for #0 AG /0 AG code conductor Copper compression CTAP taps for #8 AG 4/0 AG code conductor Copper compression HTCT taps for #4 AG 250 kcmil code conductor, #4 AG 4/0 AG flex conductor Aluminum compression lugs and splices for #6 AG 600 kcmil code conductor Aluminum compression HTAPS for #4 AG 500 kcmil code conductor PANDUIT PAN-TERM Tubular Terminals for #8 AG 250 kcmil code conductor arranty: years HTCT6-6- HTCT2-2- #6 - #0 #6 - # CT-90, CT-29 Orange, /6 Code AG AG PH6 #6 - #0 #6 - #4 Flex AG AG #2 - #6 #2 - #6 AG #8 - #4 #8 - # CT-90, CT-29 Brown, /6 Code AG STR/SO AG AG PH2 STR/SO #2 - #8 #2 - #8 AG #8 - #4 #8 - #4 Flex AG AG AG CT-29 includes: Tool Two 2 VDC, rechargeable NiMH batteries One battery charger Steel tool case with storage for batteries, charger and crimp dies HTCT kcmil - #2 - #6 AG #8 - #4 Code #2 AG STR/SO AG 4/0 - #2 #2 - #8 AG #8 - #4 Flex AG AG HTCT kcmil kcmil - Code #2 AG #2 AG 4/0 - #2 4/0 - #2 Flex AG AG CT-90, CT-29 Purple, PH CT-90, CT-29 Purple, PH Includes Application Standards and BICSI TDM Manual, 0th Edition pages

3 STRUCTUREDGROUND System for Data Center The Purpose of The grounding system is not just an insurance policy against a lightning strike. It is an active, functioning system that provides protection for personnel and equipment. Proper grounding is essential for efficient network performance. The purpose of the grounding system is to create a low impedance path to earth ground for electrical surges and transient voltages. ightning, fault currents, circuit switching (motors turning on and off), and electrostatic discharge are the common causes of these surges and transient voltages. An effective grounding system minimizes the detrimental effects of these electrical surges. A properly designed grounding system is one that is intentional, visually verifiable, adequately sized to handle expected currents safely, and one that directs these potentially damaging currents away from sensitive communication equipment. Any metallic component that is part of the data center infrastructure (such as equipment, racks, ladder racks, enclosures, cable trays, etc.) must be bonded to the grounding system. hat are the effects of improper grounding? Decreased Efficiency Electrical noise is introduced on data cables when surges are not properly dissipated by the grounding system.they cause faulty data signals and dropped packets, thus decreasing the throughput and overall efficiency of your network. ower Reliability According to insurance industry data, improper grounding of communication systems leads to $500 million per year of damage to property and/or equipment due to lightning. () The Technology Industry Council states that grounding is the single-most important factor in reliable network equipment performance. (2) More than 90% of problems in data communications equipment, including reboot, lockup, and data corruption, are traced to problems with grounding. () Industry experts estimate that 27%-% of damaged equipment in a user's facility is caused by electrostatic discharge. The component cost of repairing damaged equipment is substantial for complex circuit boards, especially when labor and downtime are considered. (4) According to the IEEE, the typical AC third prong ground is almost never sufficient to prevent damage to network equipment. (5) Safety Risks Personal injury from electric shock caused by improper grounding can cause immeasurable human suffering and significant expense. Potential fire hazards exist when heat is generated from electrical surges that find a high resistance path to ground. Can you afford improper grounding? equipment, such as switches, routers and storage devices, costs anywhere from thousands of dollars to hundreds of thousands of dollars.the cost of proper grounding is only a tiny fraction of the cost of the equipment it is protecting. Clearly the biggest cost of improper grounding is the inability to service customers properly. PANDUIT STRUCTUREDGROUND System for Data Center gives you what you need to properly protect your investment.. Mike Holt, "Prevent Shocks in Your Communications: Understanding How the NEC Relies on Ground Resistance Theory eads to a Successful Application of Communications," Electrical Construction & Maintenance, September Technology Industry Council (ITI, formerly CBEMA), Guidelines for Technology. etter, ITI, 5 February Donald G. Pennington and Paul Holzer, "Doing Battle with Those Ground Transients," Electronic Engineering Times, 8 January ESDA, "Fundamentals of ESD: Part An to ESD," 200, < ( October 2004). 5. Institute of Electrical and Electronics Engineers, Inc., IEEE Recommended Practice for Powering and Electronic, IEEE Std , 999. For service and technical support, call (outside the U.S. and Canada, see back cover).

4 PANDUIT STRUCTUREDGROUND System for Data Center is a complete, highly reliable line of products to ground your building and network equipment in compliance with BICSI TDM Manual, 0th Edition and J-STD-607-A, TIA-942, IEEE Std 00 (IEEE Emerald Book), U and CSA Telecommunications Room (see roadmap on page 8) Data Center (see roadmap on page 6) Service Entrance (see roadmap on page 5) See page 28 for PANDUIT STRUCTUREDGROUND System for Data Center Application Standards. For more data center grounding information, see 4

5 STRUCTUREDGROUND System for Data Center Service Entrance Roadmap Complies with J-STD-607-A and IEEE Std 00 (IEEE Emerald Book) Equalizer (GE) is required when two or more Telecommunications Backbones (TBB) are used within a multi-story building; bond TBBs together with a GE at the top floor and at a minimum of every third floor in between 2 Telecommunications Backbone (TBB)** 2 Conduit 5 Equalizer (GE) 6 Earth Ground 7 AC Panel* AC Service Entrance Cable Entrance 4 ater Meter 4 Copper Compression HTAP and Clear Cover: HTC (see page 9) 5 Bronze, Rod Clamp: B (see page 2) connected by a cable to 2 (U-Bolt Clamp) 2 Bronze, U-Bolt Clamp: GP (see page 22) connected by a cable to (HTAP) 6 Telecommunications Main Busbar (TMGB) and Busbar abel (see page 5) Copper Compression, Two-Hole, ong Barrel with indow ug: CC- (see pages 6-7) 7 Telecommunications and Conductor abel Kit: TYK (see page 5) 4 Bronze, ater Pipe Clamp: KP (see page 2) *AC Panel should be grounded per NEC standards. Enclosure should be grounded per manufacturer s specifications. **Specification J-STD-607-A specifies different size conductors based on the length of the Telecommunications Backbone (TBB). See page 0 for Recommended Sizing of the Telecommunications Backbone (TBB) and Equalizer (GE) Per J-STD-607-A. For service and technical support, call (outside the U.S. and Canada, see back cover). 5

6 Data Center Roadmap Complies with BICSI TDM Manual, 0th Edition and J-STD-607-A, TIA-942, IEEE Std 00 (IEEE Emerald Book), U and CSA screws are recommended to mount all panels, equipment, shelves, etc. to ensure electrical continuity between metallic components and the grounded rack Can be used to ground equipment mounted in cabinets which meet EIA-0-D; installer should bond all cabinet members to the rack grounding strip Back of Racks Shown 4 Data Racks 5 AC Panel* Telecommunications Backbone (TBB) Building Steel Conduit 2 Raised Floor Pedestal 2 Copper Compression HTAP and Clear Cover: HTC (see page 9) 4 2 Bronze, U-Bolt Clamp: GP (see page 22) 5 Telecommunications Busbar (TGB) and Busbar abel (see page 5) Telecommunications and Conductor abel Kit: TYK (see page 5) Copper Compression, Two-Hole, ong Barrel with indow ug: CC- (see pages 6-7) *AC Panel should be grounded per NEC standards. Enclosure should be grounded per manufacturer s specifications. A typical raised floor includes a multitude of metallic components which are connected together. It is the responsibility of the manufacturer and installer of the raised floor to insure all the raised floor metallic components are bonded which means that they are connected together electrically in accordance with applicable specifications. The PANDUIT / System does not insure required bonding of the raised floor metallic components. 6

7 STRUCTUREDGROUND System for Data Center Data Center Rack (Raised Floor) Back of Rack Shown Paint Piercing asher Kit: RG (see page ) Screws are used to mount patch panels to the front of the rack: RGTBS (see page 4) Jumper Kit 24", 90 Bent: RGEJ (see page 2) Electrostatic Discharge (ESD) Port Kit recommended for use on front and back of rack: RGESD (see page ) Rack Strip Kit: RGS (see page ) Jumper Kit 6", 90 Bent: RGEJ (see page 2) Jumper Kit 24", 45 Bent: RGEJ (see page 2) to Rack Jumper Kit: RGCBNJ (see page ) typically #2 AG bare copper code conductor is used underfloor For service and technical support, call (outside the U.S. and Canada, see back cover). 7

8 Telecommunications Room Roadmap Complies with BICSI TDM Manual, 0th Edition and J-STD-607-A, TIA-942, IEEE Std 00 (IEEE Emerald Book), U and CSA screws are recommended to mount all panels, equipment, shelves, etc. to ensure electrical continuity between metallic components and the grounded rack Can be used to ground equipment mounted in cabinets which meet EIA-0-D; installer should bond all cabinet members to the rack grounding strip Back of Racks Shown Equalizer (GE) Conduit 5 4 AC Panel* Telecommunications Backbone (TBB) 2 Building Steel Copper Compression HTAP and Clear Cover: HTC (see page 9) 4 Telecommunications Busbar (TGB) and Busbar abel (see page 5) 2 Bronze, U-Bolt Clamp: GP (see page 22) 5 Telecommunications and Conductor abel Kit: TYK (see page 5) Copper Compression, Two-Hole, ong Barrel with indow ug: CC- (see pages 6-7) 8 *AC Panel should be grounded per NEC standards. Enclosure should be grounded per manufacturer s specifications. A typical overhead cabling system includes a multitude of metallic components which are connected together. It is the responsibility of the installer to insure all of the metallic components are bonded, which means that they are connected together electrically in accordance with applicable specifications. The PANDUIT / System does not insure required bonding of the overhead cabling system metallic components.

9 STRUCTUREDGROUND System for Data Center Telecommunications Room Rack Aisle Ground typically #2 AG insulated copper code conductor is used overhead Back of Rack Shown Screws are used to mount patch panels to the front of the rack: RGTBS (see page 4) Paint Piercing asher Kit: RG (see page ) to Rack Jumper Kit: RGCBNJ (see page ) Jumper Kit 24", 90 Bent: RGEJ (see page 2) Electrostatic Discharge (ESD) Port Kit recommended for use on front and back of rack: RGESD (see page ) Rack Strip Kit: RGS (see page ) Jumper Kit 6", 90 Bent: RGEJ (see page 2) Jumper Kit 24", 45 Bent: RGEJ (see page 2) For service and technical support, call (outside the U.S. and Canada, see back cover). 9

10 Features and Benefits PANDUIT STRUCTUREDGROUND System for Data Center PANDUIT offers a variety of kits with premium components to ensure superior grounding with the highest reliability available. Provides highest reliability with an all-copper rack Incorporates a flexible design that can be used with grounding system to maintain data center system racks which meet EIA-0-D performance and protect network equipment Offers ease of installation no paint scraping required to Complies with data center standard TIA-942 and is U bond racks; factory terminated jumpers simply isted and CSA Certified bolt in place C A Rack Strip is made from high conductivity, low resistance wrought copper and tin plated to inhibit corrosion, providing the lowest impedance path to ground C F B Jumper has U, V- flame rated green insulation and is factory terminated with copper compression, two-hole, long barrel with window lug; lug is U isted, CSA Certified and meets NEBS evel with a single stud hole and slot which allows mounting for ½" to 5/8" hole spacing and accommodates stud sizes ¼", #2 and 6mm Electrostatic Discharge (ESD) Port Kit (see page ) E D C D Paint Piercing asher is made from hardened steel and electro zinc plated which inhibits corrosion to provide a superior bond between frame members on bolt-together racks Thread-Forming Screws are made from electro zinc plated steel and provide a bond to the rack by removing paint from threaded holes without creating metal shavings Rack Strip Kit (see page ) A E F G Electrostatic Discharge (ESD) Port is made from high conductivity, low resistance copper and tin plated to inhibit corrosion plus it functions as an ESD wrist strap hanger Electrostatic Discharge (ESD) Protection Sticker is provided in black and yellow for high visibility and easy identification as an ESD port Copper Compression HTAP is U isted and CSA Certified; used to make a highly reliable, permanent bond between the common bonding network and common bonding network to rack jumper kit D Jumper Kit (see page 2) C B B D C C 0 G to Rack Jumper Kit (see page )

11 STRUCTUREDGROUND System for Data Center Rack Strip Bonds up to 44 RU per rack EIA Universal mounting hole pattern RGS4- Part Description Rack grounding strip; 78.65" length;.67" width;.05" thickness; provided with.6 oz (5cc) of antioxidant and three #2-24 x /2" thread-forming screws* RGS rack grounding strips; 78.65" length;.67" width;.05" thickness; provided with.6 oz (5cc) of antioxidant and 0 #2-24 x /2" thread-forming screws* *An equal number of M6 x 2mm thread-forming screws also provided in each kit. to Rack Jumper Kit Bonds the rack grounding strip to the CBN HTAP, included in kit, requires crimping tool and die; see the CT-90 crimping tool on page 25, the CT-29 crimping tool on page 26 and the CD-90H-250 crimping die on page 27 HTAP is U isted and CSA Certified for applications up to 600V when crimped with PANDUIT and specified competitor crimping tools and PANDUIT crimping dies; see the Termination Solutions Catalog SA-TMCB02 for the complete line of PANDUIT crimping tools RGCBNJ660P Part Description #6 AG jumper; 60" length; 45 bent lug on grounding strip side; provided with.6 oz (5cc) of antioxidant, two #2-24 x /2" thread-forming screws* and a copper compression HTAP** for connecting to the CBN in sizes ranging from #2 AG to 250 kcmil Ctn. 0 *An equal number of M6 x 2mm thread-forming screws also provided in each kit. **HTAP also sold separately, see page 20. For service and technical support, call (outside the U.S. and Canada, see back cover).

12 Jumper Bonds network equipment to rack grounding strip Jumper kit available with both ends factory terminated to provide a bolt on solution Jumper kit available with one end factory terminated to attach to the rack grounding strip; free end accommodates unique equipment terminations Use jumpers with 90 bent lug, on grounding strip side, for high density grounding requirements up to one ground point per RU Use jumpers with 45 bent lugs, on grounding strip side, for improved cable management Use 24" jumpers when network equipment ground point is located near the grounding strip side of the rack Use 6" jumpers when network equipment ground point is located away from the grounding strip side of the rack Part Description #0 AG equipment jumpers factory terminated on both ends RGEJ024PH #0 AG jumper; 24" length; 45 bent lug on grounding strip side to straight lug on equipment; provided with.6 oz (5cc) of antioxidant and four #2-24 x /2" thread-forming screws* Ctn. 0 RGEJ024PF RGEJ024PF RGEJ06PF #0 AG jumper; 24" length; 90 bent lug on grounding strip side to straight lug on equipment; provided with.6 oz (5cc) of antioxidant and four #2-24 x /2" thread-forming screws* #0 AG jumper; 6" length; 90 bent lug on grounding strip side to straight lug on equipment; provided with.6 oz (5cc) of antioxidant and four #2-24 x /2" thread-forming screws* 0 0 #6 AG equipment jumpers factory terminated on both ends RGEJ624PH #6 AG jumper; 24" length; 45 bent lug on grounding strip side to straight lug on equipment; provided with.6 oz (5cc) of antioxidant and four #2-24 x /2" thread-forming screws* RGEJ624PF #6 AG jumper; 24" length; 90 bent lug on grounding strip side to straight lug on equipment; provided with.6 oz (5cc) of antioxidant and four #2-24 x /2" thread-forming screws* 0 0 RGEJ66PF #6 AG jumper; 6" length; 90 bent lug on grounding strip side to straight lug on equipment; provided with.6 oz (5cc) of antioxidant and four #2-24 x /2" thread-forming screws* 0 #0 AG equipment jumper factory terminated on one end RGEJ057PF #0 AG jumper; 57" length; 90 bent lug on grounding strip side; provided with.6 oz (5cc) of antioxidant and two #2-24 x /2" thread-forming screws* #6 AG equipment jumper factory terminated on one end RGEJ657PF #6 AG jumper; 57" length; 90 bent lug on grounding strip side; provided with.6 oz (5cc) of antioxidant and two #2-24 x /2" thread-forming screws* 0 RGEJ057PF *An equal number of M6 x 2mm thread-forming screws also provided in each kit. 0 How to Select the Appropriate Jumper " or smaller " or larger Select 24" equipment jumpers with 90 lugs when equipment grounding connection is close to the grounding strip. Select 6" equipment jumpers with 90 lugs when equipment grounding connection is on the opposite side from the grounding strip. Select equipment jumpers with 45 lugs for lower density applications or shallow depth equipment to provide improved cable management. 2

13 STRUCTUREDGROUND System for Data Center Paint Piercing asher Bonds frame members on bolt-together racks No paint scraping required Green color coding to indicate bonding application RG-2- Part Description 2 paint piercing bonding washers for /8" stud size;.875 O.D.; provided with.6 oz (5cc) of antioxidant; for use with standard equipment racks: CMR9X84, CMR9X84S and CMR2X84 RG-2-2 paint piercing bonding washers for /8" stud size;.875 O.D.; provided with.6 oz (5cc) of antioxidant; for use with 4 post rack NF4PR84 and data rack DR84 RG paint piercing bonding washers for /8" stud size;.875 O.D.; provided with.6 oz (5cc) of antioxidant Electrostatic Discharge (ESD) Port Kit Accommodates standard ESD wrist strap 4mm plug Can be mounted to front or back of rack for convenient access RGESD- Bent 45, acts as a hook to hold wrist strap Barrel permanently marked with the protective earth (ground) symbol Part Description ESD port kit; provided with an ESD protection sticker,.6 oz (5cc) of antioxidant and one #2-24 x /2" thread-forming screw* Contact your local electrical distributor for their selection of Electrostatic Discharge (ESD) wrist straps. *One M6 x 2mm thread-forming screw also provided in each kit. ESD port must be attached to a grounded member. For service and technical support, call (outside the U.S. and Canada, see back cover).

14 Retrofit Rack Provides a dedicated ground system to maintain system performance and protect network equipment when RGS rack grounding strip kit cannot be used (see page ) Optimized for installation on 9" racks that meet EIA-0-D, with functioning equipment, and are deployed in the field Provides a complete system of matched components that can be easily selected to save cost and labor Thread-forming screws eliminate the need to manually remove paint from the rack Rack Busbar RGRB9 HTAP (see page 20) Jumper RGREJ696 Rack Kit RGRKCBNJ ug (see pages 6-8) Rack Kit RGRKCBNJEJ Jumper RGREJ696 or RGREJ096 RGRKCBNJEJ RGRKCBNJ RGRB9 RGREJ696 RGREJ096 RGRKCBNJEJ RGRKCBNJ Part Description Rack grounding kit to ground the rack and one piece of equipment; includes one RGRB9 busbar, one HTCT HTAP and two RGREJ696 grounding jumpers Rack grounding kit to ground the rack; includes one RGRB9 busbar, one HTCT HTAP and one RGREJ696 grounding jumper Rack grounding busbar; can be positioned anywhere on the rack; 9" length; tin plated; 4 holes arranged for flexibility in mounting; mounting hole sets have /2" spacing; provided with two #2-24 x /2" thread-forming screws* for mounting jumper; #6 AG; 96" length; one end factory terminated to lug; provided with.6 oz (5cc) of antioxidant and four #2-24 x /2" thread-forming screws* and other mounting hardware as appropriate jumper; #0 AG; 96" length; one end factory terminated to lug; provided with.6 oz (5cc) of antioxidant and four #2-24 x /2" thread-forming screws* and other mounting hardware as appropriate *An equal number of M6 x 2mm thread-forming screws also provided in each kit. Ctn Thread-Forming Screws Thread-forming, provides a bond to the rack by removing paint from threaded holes without creating metal shavings Easily installed with 5/6" socket head wrench or flat blade screwdriver Part Description RGTS-C Thread-forming grounding screw, #2-24 x /2" 00 RGTSM6-C Thread-forming grounding screw, M6 x 2mm 00 Screws Creates an electrical bond between painted patch panels and racks Serrations on bottom of screw remove paint from patch panel, thus providing metal-to-metal contact Thread-forming, provides a bond to the rack by removing paint from threaded holes without creating metal shavings Easily installed with Phillips screwdriver Part Description RGTBS-C Thread-forming bonding screw, #2-24 x /2" 00 RGTBSM6-C Thread-forming bonding screw, M6 x 5mm 00 4

15 STRUCTUREDGROUND System for Data Center C UR US BICSI/J-STD-607-A Telecommunications Busbars Meets BICSI and J-STD-607-A requirements for network systems grounding applications Made of high conductivity copper and tin plated to inhibit corrosion Comes pre-assembled with brackets and insulators attached for quick installation Use PANDUIT self-laminating laser/ink jet labels to identify busbars to meet TIA/EIA-606-A TGB TMGB Bar Size No. of 5/6" hole sets, 5/8" spacing No. of 7/6" hole sets, " spacing Can Be Clearly Identified with PANDUIT aser/ink Jet abel* Telecommunications Busbars (TGB) GB2B004TPI- /4" x 2" x 0" 4 GB2B006TPI- /4" x 2" x 2" 6 C200X00FJJ GB2B02TPI- /4" x 2" x 20" 2 Telecommunications Main Busbars (TMGB) GB4B062TPI- /4" x 4" x 2" 2 6 C200X00FJJ GB4B0624TPI- /4" x 4" x 20" 24 6 For additional label sizes, materials and print technologies and to see the complete line of PANDUIT identification products, see the Identification Solutions Catalog SA-IDCB6. *Busbar labels sold separately. C200X00FJJ Telecommunications and Conductor abel Kit Meets labeling requirements of J-STD-607-A; each telecommunications grounding and bonding conductor shall be labeled as close as practicable to its point of termination in a readable position Can be applied as a wrap-around marker (parallel to cable) or flag marker (45 or 90 ) to cable Kit includes everything needed to properly label cables; one flame retardant cable tie and one rigid plastic yellow tag printed with IF THIS CONNECTOR OR CABE IS OOSE OR MUST BE REMOVED, PEASE CA THE BUIDING TEECOMMUNICATIONS MANAGER Part Description TYK abel kit includes printed tag and one flame retardant cable tie 0 For additional label sizes, materials and print technologies and to see the complete line of PANDUIT identification products, see the Identification Solutions Catalog SA-IDCB6. For service and technical support, call (outside the U.S. and Canada, see back cover). 5

16 Ring Terminal, Vinyl Expanded Insulation Expanded wire entry allows for large O.D. wire insulation or multiple wire crimps within one wire barrel Industry standard color coding to indicate wire range Brazed seam assures a reliable crimp Insulation support Requires crimping tools, see page 24 Part Number PV4-6RX-C ire Range Color Code Stock Max. Thickness Ins. Stud Size Figure Dimensions (In.) PANDUIT Tool ** Ctn. C # PV4-8RX-C 6-4 AG Blue # CT-00, PV4-0RX-C # CT PV4-4RX-C /4" PV0-6RX # PV0-8RX- 2-0 AG Yellow # CT-00, PV0-0RX # CT PV0-4RX /4" For additional sizes and configurations and to see the complete line of PAN-TERM Terminals, see the Termination Solutions Catalog SA-TMCB02. U and CSA approved tooling/product combinations. For crimping tools see page 24. **To order in bulk, replace -C in the part number with -M for a bulk package of 000 and replace - with -D for a bulk package of 500. C Code Conductor, Two-Hole, ong Barrel with indow ug For Use with Stranded Copper Conductors Meets J-STD-607-A requirements for network systems grounding applications Tested by Telcordia meets NEBS evel Requires crimping tools and dies, see pages 24, 25, 26 and 27 U isted for use up to 5KV**, temperature rated 90 C and CSA Certified to 600V when crimped with PANDUIT and specified competitor crimping tools and dies U isted and CSA Certified for wire range-taking capability when crimped with PANDUIT UNI-DIE dieless crimping tools Color coded barrels marked with PANDUIT and specified competitor die index numbers for proper crimp die selection ong barrel maximizes number of crimps and provides premium wire pull-out strength and electrical performance Inspection window to visually assure full conductor insertion Tin plated to inhibit corrosion Available with NEMA hole sizes and spacing 6

17 STRUCTUREDGROUND System for Data Center Code Conductor, Two-Hole, ong Barrel with indow ug (continued) INSPECTION INDO T HOE SPACING INSPECTION INDO B T HOE SPACING INSPECTION INDO B T HOE SPACING INSPECTION INDO B 45 T HOE SPACING 90 B Figure Figure 2: Slotted ug Figure : Slotted ug 45 Bent For service and technical support, call (outside the U.S. and Canada, see back cover). Figure 4: Slotted ug 90 Bent Stud Stud ire Copper Hole Hole Figure PANDUIT PANDUIT Burndy T&B Strip Figure Conductor Size Spacing Dimensions (In.) Die Color Die Die ength No. Size (In.) (In.) B T Tool & Die No. No. No. (In.) CC0-4JA-* 2 / /6 50 #4 #0 CC0-4JAH-* AG STR, / CT-00, 9/6 50 CC0-4JAF-* 4 #2 #0 / CT-570 9/6 50 CC0-4B-* AG SO / /6 50 CC8-0AB- 2 # Red P /4 50 CC8-4AB- 2 / CT-700, Red P /4 50 CC8-4D- #8 AG CT-90, / CT-29 Red P /4 50 CC8-8D- / Red P /4 50 CC6-0AB- 2 # Blue P /8 50 CC6-4JA- 2 / Blue P /8 50 CC6-4JAH- / Blue P /8 50 CC6-4JAF- 4 / CT-700, Blue P /8 50 CC6-4BD- 2 #6 AG CT-90, / CT-29 Blue P /8 50 CC6-4E- / Blue P /8 50 CC6-56B- 5/ Blue P /8 50 CC6-8BD- 2 / Blue P /8 50 CC4-4AD- 2 / CT-700, Gray P /8 50 #4 # CT-90, CC4-8D- AG STR / Gray P /8 50 CT-29 CC2-4A-Q / CT-700, Brown P 0 /4 25 CC2-8D-Q #2 AG CT-90, / CT-29 Brown P 0 /4 25 CC-4A-E / CT-700, Green P7 7 7/6 20 CC-8D-E # AG CT-90, / CT-29 Green P7 7 7/6 20 CC/0-4A-X / CT-90, Pink P /2 0 /0 AG CC/0-8D-X / CT-29 Pink P /2 0 CC2/0-4A-X / CT-90, Black P /6 0 2/0 AG CC2/0-8D-X / CT-29 Black P /6 0 CC/0-8D-X / Orange P /6 0 CT-90, CC/0-2-X /0 AG / CT-29 Orange P /6 0 CC4/0-4A-X / CT-90, Purple P /8 0 4/0 AG CC4/0-8D-X / CT-29 Purple P /8 0 CC250-8D-X / CT-90, Yellow P / kcmil CC250-2D-X / CT-29 Yellow P /6 0 For additional sizes and configurations and to see the complete line of PAN-UG Power and Connectors, see the Termination Solutions Catalog SA-TMCB02. *Not tested to NEBS evel requirements. **Consult cable manufacturer for voltage stress relief instructions with applications greater than 2000V. 7

18 Flex Conductor, Two-Hole, ong Barrel with indow ug For Use with Flexible, Extra-Flexible and Code Stranded Copper Conductors Meets J-STD-607-A requirements for network systems grounding applications Requires crimping tools and dies, see pages 24, 25, 26 and 27 U isted for use up to 5KV**, temperature rated 90 C and CSA Certified to 600V when crimped with PANDUIT and specified competitor crimping tools and dies Color coded barrels marked with PANDUIT and specified competitor die index numbers for proper crimp die selection Can be used with code conductor and flex conductor class: G, H, I, K, M and ocomotive ong barrel maximizes number of crimps and provides premium wire pull-out strength and electrical performance Inspection window to visually assure full conductor insertion Generously beveled wire entry prevents bent back strands when inserting conductor into barrel Tin plated to inhibit corrosion Available with NEMA hole sizes and spacing HOE SPACING INSPECTION INDO B T HOE SPACING INSPECTION INDO B T Figure Figure 2: Slotted ug Figure No. Flex Conductor Size Figure Dimensions (In.) Class G, H, I, K, M ocomotive Code Conductor Size Stud Hole Size (In.) Stud Hole Spacing (In.) B T PANDUIT Tool PANDUIT Die Color & Die No. For additional sizes and configurations and to see the complete line of PAN-UG Power and Connectors, see the Termination Solutions Catalog SA-TMCB02. **Consult cable manufacturer for voltage stress relief instructions with applications greater than 2000V. ire Strip ength (In.) CCX8-0AB- 2 # Red P2 /4 50 CCX8-4AB- 2 / CT-700, Red P2 /4 50 #8 AG #8 AG #8 AG CT-90, CCX8-4D- / Red P2 /4 50 CT-29 CCX8-8D- / Red P2 /4 50 CCX6-0B- # Blue P24 /8 50 CCX6-4AB- 2 / CT-700, Blue P24 /8 50 CCX6-4D- #6 AG #6 AG #6 AG / CT-90, Blue P24 /8 50 CCX6-8AC- 2 / CT-29 Blue P24 /8 50 CCX6-8D- / Blue P24 /8 50 CCX4-4AB- 2 / CT-700, Gray P29 /8 50 #5, #4, # #4 # CCX4-8BD- 2 #4 AG CT-90, AG AG STR / Gray P29 /8 50 CT-29 CCX2-8D-E #2 AG #2 AG #2 AG / CT-700, CT-90, CT-29 Brown P 7/6 20 CCX-4A-X / CT-90, Green P7 /2 0 # AG # AG # AG CCX-8D-X / CT-29 Green P7 /2 0 CCX/0-4A-X / CT-90, Pink P42 9/6 0 /0 AG /0 AG /0 AG CCX/0-8D-X / CT-29 Pink P42 9/6 0 CCX2/0-4A-X 2/0 AG 2/0 AG 2/0 AG / CT-90, Black P45 9/6 0 CCX2/0-8D-X / CT-29 Black P45 9/6 0 CCX/0-8D-X /0 AG /0 AG /0 AG / CT-90, Orange 5/8 0 CT-29 P50 CCX4/0-8D-X 4/0 AG 4/0 AG 4/0 AG / CT-90, Purple 2 5/6 0 CT-29 P54 CCX250-8D-X 250 kcmil kcmil / CT-90, CT-29 Yellow P62 2 5/6 0 8

19 STRUCTUREDGROUND System for Data Center Code/Flex Conductor HTAP Kit Includes all components to make a complete HTAP and cover installation: HTCT HTAP, matching CRCVR clear cover and cable ties Each HTCT HTAP designed to terminate a wide range of copper code and flex conductor combinations to accommodate a variety of applications HTAPs incorporate a unique slotted design that allows for quick and easy installation using supplied PANDUIT cable ties; saves time and cost Matching clear covers are made from high impact plastic and provide high impact strength and 60 viewing of installed HTAP Clear covers have a U 94 V-0 flame rating and an oxygen index of 28 providing self-extinguishing, flame retardant properties Requires crimping tools and dies, see pages 25, 26 and 27 U isted and CSA Certified for applications up to 600V when crimped with PANDUIT and specified competitor RUN RUN RUN RUN H TAP H TAP 2 TAP TAP H TAP TAP 2 TAP HTCT6-6 HTCT2-2 HTCT250-2 HTCT H Clear Cover Part No. Copper Conductor Size Range ire Strand Type Run Tap Tap 2 Tap HTAP Part No. HTC6-6- HTCT6-6- CRCVR- Code #6 #0 AG #6 #4 AG Flex #6 #0 AG #6 #4 AG HTC2-2- HTCT2-2- CRCVR2- #2 #6 AG #2 #6 AG #8 #4 AG #8 #4 AG Code STR/SO STR/SO Flex #2 #8 AG #2 #8 AG #8 #4 AG #8 #4 AG HTC HTCT CRCVR- 250 kcmil #2 #2 #6 AG #8 #4 AG Code AG STR/SO Flex 4/0 #2 AG #2 #8 AG #8 #4 AG HTC HTCT CRCVR- 250 kcmil #2 250 kcmil #2 Code AG AG Flex 4/0 #2 AG 4/0 #2 AG For additional sizes and configurations and to see the complete line of PAN-UG Power and Connectors, see the Termination Solutions Catalog SA-TMCB02. See pages 20 and 2 for more information on HTAPs and clear covers, including crimping tools. abels for clear covers are sold separately and are printed with the PANDUIT S7 Printer. For information on the S7 Printer and to see the complete line of PANDUIT identification products, see the Identification Solutions Catalog SA-IDCB6. For service and technical support, call (outside the U.S. and Canada, see back cover). 9

20 Code/Flex Conductor HTAP For Making Parallel and Multiple Tap Connections on Code and Flex Conductors HTAP RUN Used to tap into continuous conductors as a splice or pigtailing Each HTAP terminates a wide range of conductor sizes and combinations of code and flex conductors Class G, H, I and ocomotive to suit a variety of applications Slotted design allows quick and easy assembly of conductor to HTAP using PANDUIT 94 V-0 cable ties included TAP Tap grooves are separated from one another allowing them to function independently so HTAP can be used with a single or multiple taps providing maximum design and installation flexibility Color coded and marked with PANDUIT die index numbers for proper crimp die selection Requires crimping tools and dies, see pages 25, 26 and 27 U isted and CSA Certified for applications up to 600V when crimped with PANDUIT and specified competitor crimping tools and PANDUIT crimping dies Tin plated to inhibit corrosion RUN RUN RUN RUN H H H H TAP HTCT6-6- HTCT2-2- HTCT TAP 2 TAP TAP TAP TAP 2 TAP HTCT6-6 HTCT2-2 HTCT250-2 HTCT Figure Copper Conductor Size Range Dimensions (In.) ire Strand Type Run Tap Tap 2 Tap H Code Flex Code Flex Code #6 #0 AG #6 #0 AG #2 #6 AG STR/SO #2 #8 AG 250 kcmil #2 AG 4/0 #2 Flex AG HTCT kcmil Code #2 AG Flex 4/0 #2 AG #6 #4 AG #6 #4 AG #2 #6 AG STR/SO #8 #4 AG #2 #8 AG #8 #4 AG #2 #6 AG STR/SO #8 #4 AG #2 #8 AG #8 #4 AG 250 kcmil #2 AG 4/0 #2 AG #8 #4 AG #8 #4 AG PANDUIT Tool PANDUIT Die Color & Die No CT-90, CT-29 Orange, PH CT-90, CT-29 Brown, PH CT-90, CT-29 Purple, PH CT-90, CT-29 Purple, PH25 ire Strip ength (In.) /6 /6 For additional sizes and configurations and to see the complete line of PAN-UG Power and Connectors, see the Termination Solutions Catalog SA-TMCB02. 20