Wire Rope and Cable Fittings

Transcription

1 Wire Rope and Cable Fittings 85 Broadcommon Road Bristol, RI Tel Fax Greenleaf Avenue Elk Grove Village, IL Tel Fax

2 Cautions Important: Read Warnings Before Using this Publication It is of the utmost importance that anyone using this publication read and understand all warnings and other information listed below and/or adjacent to the product description and preceding each product section. All Products are sold with the understanding that the purchaser is familiar with the correct application and safe use. Use all products properly, in safe manner and for the application for which they are intended. M&G assumes no responsibility for the use or misapplication of any product sold by this firm. Responsibility for design and use decisions rest with the user. Important Warnings Remember: any product will break if abused, misused or overused. Any well-designed and well-built product can become hazardous in the hands of a careless user. Therefore: Never exceed the work load limit Match components properly Keep out from under a raised load Avoid shock loads Inspect products regularly Work Load Limits Never exceed the work load limit (WLL), safe working load (SWL) rated capacity. The work load limit is the maximum load which should never be applied to the product, even when the product is new and when the load is uniformly applied- straight line pull only. Avoid side loading. All catalog ratings are based upon usual environmental conditions, and consideration must be given to unusual conditions such as high or low temperatures, chemical solutions or vapors, prolonged immersion in salt water, etc. Such conditions or high-risk applications may necessitate reducing the work load capacity. Work load limit will not apply if product has been welded or otherwise modified. Matching of components Components must match. Make certain that components such as hooks, links of shackles, etc., used with wire rope (or chain or cordage) are of suitable material and strength to provide adequate safety protection. Attachments must be properly installed and must have a work load limit at least equal to the products with which they are used. Remember: any chain is only as strong as its weakest link. Raised Load Keep out from under a raised load. Take notice of the recommendation from the National Safety Council Accident Prevention Manual concerning all lifting operations: All employees working at cranes or hoist or assisting in hooking or arranging a load should be instructed to keep out from under the load. From a safety standpoint, one factor is paramount: Conduct all lifting operations in such a manner, that if there were an equipment failure, no personnel would be injured. This means keep out from under a raised load and keep out of the line of force of any load. Shock Loads Avoid impacting, jerking or swinging of load Work Load Limit will not apply. A shock load is generally significantly greater than the static load. Avoid shock loads. Regular Inspection Inspect products regularly for visible damage, cracks, wear, elongation, rust, etc. Protect all products from corrosion. The need for periodic inspection cannot be overemphasized. No product can keep operating at its rated capacity indefinitely. Periodic inspections help determine when to replace a product and reduce rigging hazards. Keep inspection records to help pinpoint problems and to insure periodic inspection intervals. Due to the diversity of the products involved and uses to which they can be put, it would be counterproductive to make blanket recommendations for inspection procedures and frequency. Best results will be achieved when qualified personnel base their decisions on information from rigging and engineering manuals and on experience from actual use in the field. Frequency of inspection will depend on environmental conditions, application, storage of product prior to use, frequency of use, whether or not life, limb or valuable property are at risk, etc. When in doubt, inspect products prior to each use. Carefully check each item for wear, deformation, cracks or elongation, a sure sign of imminent failure. Immediately withdraw such items from service. Rust damage is another potential hazard. When in doubt about the extent of corrosion or other damage, withdraw the items from service. Destroy, rather than discard, items that have been judged defective. They might be used by someone not aware of the hazard of the defect.

3 Page Introduction 2-4 General Purpose Wire Ropes 5-6 Specialty Wire Ropes M&G Industries was founded by Martin G. Rosenthal in 1974 Trawlmaster & Stainless Steel Ropes 8 Galvanized Cable, Stainless Steel Cable 9-10 Vinyl Coated Cables, Strand, Deck Lashing Chains, Links Hooks Load Binders 17 Thimbles, Swage Fittings 18 Chain Links & Swivels 19 Wire Rope Clips 20 Shackles, Hammer Locks, Weldable Grab Hooks Turnbuckles & Cleats Stainless Steel Fittings Cable and Wire Cutters, Swaging Tools 28 Conversion Tables 29 Member Associated Wire Rope Fabricators 100% Women Owned Business Member Small Business Association

4 M & G Industries is in business to help its customers successfully compete in their respective markets. As a company we take pride in our pledge to supply only as a wholesale distributor. We provide goods to distributors in industries ranging from commercial fishing and cargo transport to agriculture and construction. We also supply wire rope fabricators, selling to segments of the commercial construction sector, with products for use in applications pertaining to railways, bridges, highways, cranes and buildings. M & G is a key supplier for many OEM businesses, including such fields as automotive control cables, overhead doors, guyed towers and prefabricated concrete. The OEM materials we supply can be general purpose in nature and/or specialized, specific to a customer s needs. The home gym and tie-down pet industries, for example, depend on the high-quality coated cables we sell for their systems. Quality and service are the standards by which our mutually loyal customer base has been built. We thank those who have stood with us and we invite other distributors to become a part of our family. Our specialized line for fishing vessels is called Trawlmaster and was developed with MIT for enhanced performance over standard trawl ropes. In fact, our Trawlmaster line is the most respected and asked for trawl rope in the fishing industry today. Time tested, it has lasted longer and been more consistent than competitive ropes on the market. This focus on quality extends throughout our products. Our yacht rigging cable can be found on all types of ships from a world-class racing vessel to a backyard sailboat. Rigging and Spar professionals use many of our stainless steel wire rope products. M & G s cable and rigging hardware will withstand the most severe environmental conditions while delivering superb performance.

5

6 M&G Industries was started in 1974 by its late founder, Marty Rosenthal. As was his wish, our commitment to the customer has endured. For more than 30 years this familyrun business has been an Importer and Wholesale Distributor of wire rope, cable, chain and fittings. Our business focuses on supplying many different markets throughout North America. We only provide best-in-class materials and do so at the best available price, coupled with industry best delivery. Only ISO certified manufacturers supply us with our wire ropes and cables. M & G imports from a select few suppliers to ensure a consistent quality for our customers. All of the products we sell meet or exceed their respective Federal Standard, and are rated accordingly. All of our material is backed by a 100% flaw free guarantee. In order to better serve certain consumption sectors, M & G Industries has acquired a custom 4-head re-spooling machine. This re-spooler allows us to process multiple cutto-length orders in a more expedient fashion. We are now able to ship orders up to four times faster, getting them into our customers hands more quickly and efficiently. M & G can supply container load quantities on a direct import basis for any items shown in our catalog. Specialty items are also available on a direct import basis.

7 Bright Wire Rope Foot Fiber Core (IPS) Foot IWRC (EIPS) 1/4".105 5, ,800 5/16".164 8, ,540 3/8" , ,100 7/16".32 16, ,400 1/2".42 21, ,600 9/16".53 27, ,600 5/8".66 33, ,200 3/4".95 47, ,800 7/8" , ,600 1" , , /8" , , /4" , , /8" , , /2" , , /8" , , /4" , ,000 2" , , /4" , , /2" , , /4" , ,000 3" , ,000 Wire Rope 6x19 Class 6x25 Filler Wire with Fiber Core 6x26 Warrington Seale with IWRC 6x25 Filler Wire with IWRC 6x19 Seale with IWRC s above 1-1/2 are typically available on a special order basis. Foot Fiber Core (IPS) Foot IWRC (EIPS) 1/4".105 5, ,800 5/16".164 8, ,540 3/8" , ,100 7/16".32 16, ,400 1/2".42 21, ,600 9/16".53 27, ,600 5/8".66 33, ,200 3/4".95 47, ,800 7/8" , ,600 1" , , /8" , , /4" , , /8" , , /2" , , /8" , , /4" , ,000 2" , , /4" , , /2" , , /4" , ,000 3" , ,000 Wire Rope 6x37 Class 6x36 Warrington Seale with Fiber Core 6x36 Warrington Seale with IWRC 5 All materials produced according to federal specifications RR-W-410D & RR-W-410E, preformed, right regular lay. Bristol, RI , Elk Grove Village, IL

8 Galvanized Wire Rope Foot Fiber Core (IPS) Foot IWRC (EIPS) 1/4".105 4, ,120 5/16".164 7, ,480 3/8" , ,600 7/16".32 14, ,360 1/2".42 19, ,000 9/16".53 24, ,200 5/8".66 30, ,000 3/4".95 42, ,000 7/8" , ,600 1" , , /8" , , /4" , , /8" , , /2" , , /8" , , /4" , ,000 2" , , /4" , , /2" , , /4" , ,000 3" , ,000 Wire Rope 6x19 Class 6x25 Filler WIre with Fiber Core 6x26 Warrington Seale with IWRC 6x25 Filler WIre with IWRC Foot Fiber Core (IPS) Foot IWRC (EIPS) 1/4".105 4, ,120 5/16".164 7, ,480 3/8" , ,600 7/16".32 14, ,360 1/2".42 19, ,000 9/16".53 24, ,200 5/8".66 30, ,000 3/4".95 42, ,000 7/8" , ,600 1" , , /8" , , /4" , , /8" , , /2" , , /8" , , /4" , ,000 2" , , /4" , , /2" , , /4" , ,000 3" , ,000 Wire Rope 6x37 Class 6x36 Warrington Seale with Fiber Core 6x36 Warrington Seale with IWRC s above 1-1/2 are typically available on a special order basis. All materials produced according to federal specifications RR-W-410D & RR-W-410E, preformed, right regular lay. 6 M&G Industries, Inc.

9 Specialty Wire Ropes Foot 19x7 Non-rotating Brt 1/4".133 5,540 5/16".177 8,600 3/8".25 12,300 7/16".35 16,660 1/2".45 21,600 9/16".58 27,200 5/8".71 33,600 3/4" ,000 7/8" ,000 1" , /8" ,200 Rotation Resistant Wire Rope 19x7 Non-rotating Wire Strand Core GLV & SS also available According to federal specification RR-410D & RR-W-410E. WSC, bright, medium lube preformed EIPS. These wire ropes are specially designed for use when rotation must be kept to a minimum. Strict adherence to breaking-in procedures and proper handling during use are extremely important with these ropes. Construction Cable-Laid Wire Rope 3/8" 7x7x /2" 7x7x /8" 7x7x /4" 7x7x /8" 7x7x " 7x7x /8" 7x7x /4" 7x7x To be used for mechanical swaged slings only. Foot in Tons Galvanized Cable-Laid 7x7x7 7x7xS19 7 Bristol, RI , Elk Grove Village, IL

10 Trawlmaster THE BRAND FISHERMEN ASK FOR BY NAME Trawlmaster Wire Rope 6x7 Poly Core Galvanized Foot 6x19 Poly. Core Galvanized Foot 1/4".094 4, ,940 5/16".15 7, ,660 3/8".21 10, ,980 7/16v.29 14, ,880 1/2v.38 18, ,260 9/16".48 23, ,300 5/8".59 28, ,000 11/16" ,300 3/4".84 40, ,800 13/16" ,010 7/8" , ,000 1" , , /8" , ,600 6x7 PPC Galv. 6x19 (S) PPC Galv. 6x26 (WS) PPC Galv. Available in A1 or C LUBE Stainless Steel Wire Rope 6x19 Stainless Steel Wire Rope - Type 304 6x37 Stainless Steel Wire Rope - Type Feet 1000 Feet 7/16".35 16, ,300 1/2".46 22, ,800 9/16".59 28, ,500 5/8".72 35, ,000 3/4" , ,600 7/8" , ,500 1" , , /8" 106, , /4" 129, , /8" 153, ,600 6x19 IWRC Wire Rope/Stainless Steel Type 304 6x36 Warrington Seale with IWRC According to Federal Specifications RR-W-410D & RR-W-410E. Meeting dimensional and strength requirements of MIL-W x25 Filler Wire with IWRC 8 M&G Industries, Inc.

11 Galvanized Cable 1000 Feet 1x7 Galvanized Cable * 1x19 Galvanized Cable 1000 Feet * 1/64" /23" /64" /16" /64" /32" , ,200 7/64" , /8" , ,100 5/32" ,300 3/16" ,700 1/4" ,200 5/16" ,500 3/8" ,000 Galvanized Cable 1x7 1x Feet 7x7 Galvanized Cable * 7x19 Galvanized Cable 1000 Feet * 1/16" ** /64" ** /32" ** ,000 1/8" , ,000 5/32" , ,800 3/16" , ,200 7/32" ** , ,600 1/4" ** , ,000 5/16" ** , ,800 3/8" ** , ,400 7x7 7x19 * Listed for comparison only. Actual operating loads may vary, but should never exceed recommended design factor or 1/7 of catalog breaking strength. ** Listed for comparison only. Actual Factors vary between 6:1 and 3:1 depending on application. Diameter of Wire Rope The diameter of wire rope is the diameter of the circle which encloses all the wires. When measuring wire rope it is important to take the greatest distance of the outer limits of the crown of two opposite strands. A measurement across the valleys will result in incorrect lower readings. Correct Incorrect 9 Bristol, RI , Elk Grove Village, IL

12 Stainless Steel Cable 7x7 Stainless Steel Cable - Type 304 7x19 Stainless Cable - Type Feet * 1000 Feet * 1/16" ** /32" ** /8" ** , ,760 5/32" ** , ,400 3/16" ** , ,700 7/32" ** ,000 1/4" ** ,400 5/16" ** ,000 3/8" ** ,000 Stainless Steel Cable Type 304 7x7 7x19 7x7 Stainless Steel Cable - Type 316 7x19 Stainless Cable - Type Feet * 1000 Feet * 1/16" /32" /8" ,670 3/16" ,565 1/4" ,875 5/16" ,825 3/8" ,760 Stainless Steel Cable Type 316 7x7 7x19 1x19 Stainless Steel Strand ** 1000 Feet Type 304 Type 316 1/16" /32" ,200 1,020 1/8" ,100 1,780 5/32" ,300 2,800 3/16" ,700 4,000 7/32" ,300 5,350 1/4" ,200 6,900 5/16" ,500 10,600 3/8" ,500 14,800 Stainless Steel Cable 1x19 * Listed for comparison only. Actual operating loads may vary, but should never exceed recommended design factor or 20% of catalog breaking strength. ** According to Federal Specifications RR-W-410D & RR-W-410E. Meeting dimensional and strength requirements of MIL-W-83420D. 10 M&G Industries, Inc.

13 Vinyl Coated Cable Coated to Vinyl Coated Galvanized Cable 1000 Foot * Construction 1/16" ** 3/ x7 1/16" ** 1/ x7 3/32" ** 1/ x7 3/32" ** 3/ x7 1/8" ** 3/ ,700 7x7 3/32" ** 1/ ,000 7x19 1/8" ** 3/ ,000 7x19 3/16" ** 1/ ,200 7x19 1/4" ** 5/ ,000 7x19 5/16" ** 3/ ,800 7x19 3/8" ** 7/ ,400 7x19 Vinyl Coated Cable Galvanized 7x7 7x19 Coated to 7x7 Life-Line 1000 Foot * 1/16" 1/ /32" 1/ /8" 3/ ,700 1/8" 7/ ,700 1/8" 1/ ,700 3/16" 1/ ,700 3/16" 5/ ,700 3/16" 3/ ,700 1/4" 3/ ,100 Life-line Cable/White Jacketed Stainless Steel Type 304 7x7 Coated to Vinyl Coated Stainless Cable Type 304 Approx.. Weight per 1000 Foot Construction 1/8" ** 3/ ,760 7x19 3/16" ** 1/ ,700 7x19 1/4" ** 5/ ,400 7x19 5/16" ** 3/ ,000 7x19 3/8" ** 7/ ,000 7x19 Vinyl Coated Cable Stainless Steel 7x19 * Listed for comparison only. Actual operating loads may vary, but should never exceed recommended design factor or 1/7 of catalog breaking strength. ** Listed for comparison only. Actual Factors vary between 6:1 and 3:1 depending on application. 11 Bristol, RI , Elk Grove Village, IL

14 Guy Strand 1000 Feet 1x7 Galvanized Steel Strand ** Galvanized Steel Strand 3/16" 73 3,990 1/4" 121 6,650 5/16" ,200 3/8" ,400 1/2" ,900 According to ASTM A 475, class A coating, left lay regular lay, extra high strength 1x7 Deck Lashing * 6x15+7 Fiber Core Lashing Wire Rope Foot Fiber Core Lashing Wire Rope 1/2" 12, /8" 19, /4" 27, * Listed for comparison only. Actual operating loads may vary, but should never exceed recommended design factor or 1/7 of catalog breaking strength. ** Listed for comparison only. Actual Factors vary between 6:1 and 3:1 depending on application. 6x15+7 Wire Rope WILL FAIL if worn-out, overloaded, misused, damaged, improperly maintained or abused. Wire rope failure may cause serious injury or death! Protect yourself and others: * ALWAYS INSPECT wire rope for WEAR, DAMAGE or ABUSE BEFORE USE. NEVER USE wire rope that is WORN-OUT, DAMAGED or ABUSED. NEVER OVERLOAD a wire rope. INFORM YOURSELF: Read and understand manufacturer's literature or "Wire Rope and Wire Rope Sling Safety Bulletin".* REFER TO APPLICABLE CODES, STANDFARDS and REGULA- TIONS for INSPECTION REQUIREMENTS and REMOVAL CRITERIA.* For additional information or the BULLETIN, ask your employer or wire rope supplier. 1993, Wire Rope Technical Board Form No M&G Industries, Inc.

15 Chain Trade Working Load Limit Feet per Drum Proof Coil Chain / Grade 30 Feet per 1/2 Drum Minimum Weight per Foot Maximum Length per 100 Links 1/8" 375 2,000 1, " 3/16" 800 1, " 1/4" 1, " 5/16" 1, " 3/8" 2, " 1/2" 4, " 5/8" 6, " 3/4" 10, " 7/8" 12, " 1" 13, " Proof Coil Chain Grade 30 / Self Colored-Zinc Plated-Hot Galvanized Trade High Test Chain / Grade 43 Working Load Limit Feet per Drum Feet per 1/2 Drum Minimum Weight per Foot Maximum Length per 100 Links 1/4" " 5/16" " 3/8" " 1/2" " 5/8" " 3/4" " High Test Chain Grade 43 / Self Colored-Hot Galvanized Trade Working Load Limit Transport Chain / Grade 70 Yellow Chromatized Feet per Drum Feet per 1/2 Drum Minimum Weight per Foot Maximum Length per 100 Links 1/4" 3, " 5/16" 4, " 3/8" 6, " 1/2" 11, " Transport Chain Grade 70 / Yellow Chromatized Trade Alloy Chain / Grade 80 Working Load Limit Approx. Weight per 100 Ft. in Lbs. Actual Material Diameter Inside Length Inside Width 9/32" 3, /8" 7, /2" 12, /8" 18, /4" 28, /8" 34, " 47, Alloy Chain Grade 80 Domestic All chains comply with NACM standards 13 Bristol, RI , Elk Grove Village, IL

16 Chain Trade Working Load Limit Stainless Steel Chain / T316 Feet per Drum Weight per Foot 1/8" 375 1, /16" 750 1, /4" 1, /16" 1, /8" 2, /2" 4, Stainless Steel Chain T316 All chains comply with NACM standards Link chain fitting minimum breaking strength = 6 x W.L.L. Links (D) Working Load Limit in Lbs. (Single Pull) Pair Shaped Sling Links, High Test Approx. Weight Each Inside Length L W1 Inside Width 3/8" 1, " 1.50".75" 1/2" 2, " 2.00" 1.00" 5/8" 4, " 2.50" 1.25" 3/4" 6, " 2.75" 1.38" 7/8" 8, " 3.50" 1.75" 1" 10, " 3.75" 1.88" 1.1/4" 16, " 5.00" 2.50" 1.3/8" 20, " 5.50" 2.75" 1.1/2" 25, " 6.00" /4" 34, " 7.00" 3.50" 2" 45, " 8.00" 4.00" 2.1/4" 56, " 9.00" 4.50" 2.1/2" 68, " 10.00" 5.00" 2.3/4" 84, " 11.00" 5.50" W2 Pear Shaped Sling Links High Test Heat Treated, Painted (D) Oblong Master Link, Alloy Working Load Limit in (Single Pull) Approximate Weight Each Inside Length L Inside Width W 1/2" 4, " 2.25" 5/8" 5, " 3.00" 3/4" 8, " 3.00" 1" 20, " 4.00" 1.1/4" 29, " 5.00" 1.1/2" 39, " 6.00" 1.3/4" 52, " 6.75" 2" 81, " 7.50" 2.1/4" 99, " 8.00" 2.1/2" 122, " 8.50" 2.3/4" 148, " 10.00" 3" 190, " 10.50" 3.1/2" 232, " 12.00" 4" 275, " 14.00" Oblong Master Links, Alloy Heat Treated, Painted 14 M&G Industries, Inc.

17 Hooks Working Load Limit in Approximate Weight Each High Test Clevis Grab Hooks / Grade 40 A B C D 1/4" 2, /16" 3, /8" 5, /2" 9, /8" 12, High Test Clevis Grab Grade 43/Self Colored-Zinc Plated-Hot Galvanized Working Load Limit in Approximate Weight Each Alloy Clevis Grab Hooks / Grade 70 A B C D 1/4" 3, /16" 5, /8" 7, /2" 12, Alloy Clevis Grab Grade 70/Self Colored-Zinc Plated-Hot Galvanized Yellow Chromatized Working Load Limit in Approximate Weight Each High Test Clevis Slip Hooks / Grade 40 A B C D 1/4" 1, /16" 2, /8" 4, /2" 6, High Test Clevis Slip Grade 43/Forged Steel, Heated Treated, Painted with or without latch Working Load Limit in Approximate Weight Each Alloy Clevis Slip Hooks / Grade 70 A B C D 1/4" 2, /16" 4, /8" 5, /2" 9, Alloy Clevis Slip Grade 70/Self Colored-Zinc Plated-Hot Galvanized Yellow Chromatized with or without latch Clevis Hook Fitting Minimum = 4 x W.L.L. 15 Bristol, RI , Elk Grove Village, IL

18 Hooks (WLL) Carbon Alloy Eye Hoist Hooks/Carbon or Alloy Steel Wt. with Latch in Lbs. A B C D E F G H J K Eye Hoist Hooks 3/4 ton 1 ton / / / / Eye Hoist Hook Minimum = 5 x W.L.L. Carbon or Alloy Steel with or without Latch Hook Carbon Alloy Stainless Latch Kit Approximate Weight Each 3/4 ton 1 ton / / / / Latch Kit Stainless Steel Working Load Limit in Approximate Weight Each High Test Eye Grab Hooks / Grade 40 A B C D 1/4" 2, /16" 3, /8" 5, /2" 9, High Test Eye Grab Grade 40/Forged Steel, Heated Treated, Painted Red Working Load Limit in Approximate Weight Each High Test Eye Slip Hooks / Grade 40 A B C D 1/4" 1, /16" 2, /8" 4, /2" 6, High Test Eye Slip Grade 40/Forged Steel, Heat Treated, Painted Eye Slip Hook and Grab Hook Minimum = 4 x W.L.L. 16 M&G Industries, Inc.

19 Hooks Sorting Hook / Forged Alloy Steel, Heated Treated Working Load Limit 2.1/2" from Tip 2 Ton Working Load Limit, at Bottom 7.1/2 Tons Approximate Weight Each 6.75 Overall Length L 9.69" I.D. of Eye A 1.38" Opening at Top of Hook O 2.81" Radius at Bottom of Hook R.63" Sorting Hooks Forged Alloy Steel, Heat Treated Sorting Hook Minimum = 5 x W.L.L. Working Load Limits Snap Hook / Forged Steel, Electro Galvanized A B C D E F G H Approximate Weight Each 7/ Snap Hooks Forged Steel, Electro Galvanized Load Binders Working Load Limit Standard Load Binders Lever Type Approx. Weight Each Take-up 1/4"-5/16" 2,600 9, /2" 5/16"-3/8" 5,400 19, /4" 3/8"-1/2" 9,200 33, /4" Standard Lever and Ratchet Type Load Binders Forged Steel, Heated Treated, Painted Working Load Limit Load Binders Ratchet Type Approx. Weight Each Take-up 5/16"-3/8" 5,400 19, " 3/8"-1/2" 9,200 33, " 17 Bristol, RI , Elk Grove Village, IL

20 Wire Rope Thimbles Trade Approx. Weight Each Heavy Duty Wire Rope Thimble / Galvanized A B C D E 1/4" /16" /8" /16" /2-9/16" /8" /4" /8" " /8"-1.1/4" /4"-1.3/8" /8"-1.1/2" /8" /4" /8"-2" /4" /2" Heavy Duty Wire Rope Thimble Hot Galvanized Approx. Weight Each Regular Wire Rope Thimble / Zinc Plated A B C D E 1/8" /16" /4" /16" /8" /2" /8" /4" /8" " /8"-1.1/4" Standard Duty Wire Rope Thimble Zinc Plated Swage Fittings Cable Sleeves Stops Aluminum Weight 1000 Pieces/ Copper Weight 1000 Pieces/ Aluminum Weight 1000 Pieces/ Copper Weight 1000 Pieces/ 1/16" /32" /8" /8"-3/16" 5.2 5/32" /16" /4" /16" /8" Sleeves and Stops Aluminum, Copper & Copper Zinc Plated 18 M&G Industries, Inc.

21 Chain Links Working Load Limit in Approximate Weight Each Connecting Links A B C D 3/16" /4" 1, /16" 1, /8" 2, /2" 4, Connecting Links Forged Steel, Heat Treated, Electro Galvanized Working Load Limit in Approximate Weight Each Quick Links (Rapid) A B C D 1/8" /16" /4" /16" 1, /8" 2, /2" 3, Quick Links Rapid Electro Galvanized (A) Working Load Limit in Approximate Weight Each Eye & Eye Swivels-Hot Galvanized B C E F 1/4" /16" 1, /8" 2, /2" 3, /8" 5, /4" 7, /8" 10, " 12, /8" 15, /4" 18, /2" 45, Swivels Eye & Eye Swivels Hot Galvanized (A) Working Load Limit in Approximate Weight Each Jaw & Eye Swivels-Hot Galvanized B C D E F G 1/4" /16" 1, /8" 2, /2" 3, /8" 5, /4" 7, /8" 10, " 12, /8" 15, /4" 18, /2" 45, Jaw & Eye Swivels Hot Galvanized 19 Bristol, RI , Elk Grove Village, IL

22 Wire Rope Clips Min. Clips Required Amt. Wire Rope to Turn Back Torque in Foot Approx. Weight in Malleable Wire Rope Clips A B C D E F G 1/16" 3 4" /8" 3 4.3/4" /16" 3 5.1/2" /4" 3 7" /16" 3 7.3/4" /8" 3 9.1/2" /16" /4" /2" /4" /16" 4 16" /8" 4 16" /4" /4" /8" /2" " 6 31" /8" 7 39" Malleable Wire Rope Clips Galvanized Min. Clips Required Amt. Wire Rope to Turn Back Torque in Foot Approx. Weight in Drop Forged Wire Rope Clips A B C D E F G 1/8"* 2 3.1/4" /16" 2 3.3/4" /4" 2 4.3/4" /16" 2 5.1/4" /8" 2 6.1/2" /16" 3 7" /2" /2" /16" 3 12" /8" 3 12" /4" 4 18" /8" 4 19" " 5 26" /8" 6 34" /4" 7 44" /8" 7 44" /2" 8 54" /4" 8 61" " 8 71" /4" 8 73" /2" 9 84" /4" " " " 1, Drop Forged Wire Rope Clips Hot Dipped Galvanized 20 M&G Industries, Inc.

23 Shackles (A) Work Load Limit in Pin Diameter in Approx. Weight Each Anchor Shackle Screw Pin/Galvanized Tons Inches (B) C D E F 3/16" 1/3 1/ /4" 1/2 5/ /16" 3/4 3/ /8" 1 7/ /16" 1.1/2 1/ /2" 2 5/ /8" 3.1/4 3/ /4" 4.3/4 7/ /8" 6.1/ " 8.1/2 1.1/ /8" 9.1/2 1.1/ /4" / /8" 13.1/2 1.1/ /2" / /4" " / /4" / /2" / " / Anchor Shackles Screw Pin Galvanized, Available in Commercial Grade (A) Work Load Limit in Pin Diameter in Approx. Weight Each Anchor Shackle Screw Pin/Galvanized Tons Inches (B) C D E F 3/4" 7 7/ /8" " / /4" / /2" / /4" " / /2" / " / /2" / " / /4" / /4" / /8" / /8" /4 1, " /2 3, /2" 1, , Anchor Shackles Bolt Type Alloy Steel, Available as Chain Shackles (A) Work Load Limit in Pin Diameter in Approx. Weight Each Towing Shackles / Alloy Tons Inches (B) C D E F 1.1/2" / /4" " / /2" / " / Towing Shackles Alloy Steel 21 Bristol, RI , Elk Grove Village, IL

24 Shackles (A) Work Load Limit in Bolt Diameter in Approx. Weight Each Chain Shackles Bolt Type / Galvanized Tons Inches (B) C D E 1/2" 2 5/ /8" 3.1/4 3/ /4" 4.3/4 7/ /8" 6.1/ " 8.1/2 1.1/ /8" 9.1/2 1.1/ /4" / /8" 13.1/2 1.1/ /2" / /4" " / /2" / " / /2" / Chain Shackles Bolt Type Galvanized Hammer Locks Work Load Approx. Hammer Locks Limit in Weight Each Tons A B C 3/8" /2" /8" /4" /8" " Hammer Locks Grade 80 Weldable Grab Hook Rockwell Hardness Yield Point in Weldable Grab Hook Ultimate Failure in Weight 5/16" ,500-10,000 12, /2" upon request upon request 32, Weldable Grab Hook Carbon Steel Self Colored 22 M&G Industries, Inc.

25 Turnbuckles ( x Take-up) Approximate Weight Each in Approximate Weight Each Eyes and / or Hooks Turnbuckles / Hot Galvanized, Drop Forged Jaw & Eye Working Load Limit in Lbs. Hook & Hook Hook & Eye Eye & Eye \Jaw & Eye Jaw & Jaw Av. Overall Lght. with Ends in Closed Pos. 1/4"x4" /16"x4.1/2" /8"x6" ,000 1, /2"x6" ,500 2, /2"x9" ,500 2, /2"x12" ,500 2, /8"x6" ,250 3, /8"x9" ,250 3, /8"x12" ,250 3, /4"x6" ,000 5, /4"x9" ,000 5, /4"x12" ,000 5, /4"x18" ,000 5, /8"x12" ,000 7, /8"x18" ,000 7, "x6" ,000 10, "x12" ,000 10, "x18" ,000 10, "x24" ,000 10, /4"x12" ,000 15, /4"x18" ,000 15, /4"x24" ,000 15, /2"x12" ,500 21, /2"x18" ,500 21, /2"x24" ,500 21, /4"x18" , /4"x24" , "x24" , /2"x24" , /4"x24" , Turnbuckles Hot Galvanized, Drop Forged Jaw & Jaw Hook & Eye Hook & Hook Eye & Eye Jaw & Eye Details on opposite page Cleats Length Open Based Cleat / Galvanized Iron Bolt Weight 4" #10 FH.24 5" #10 FH or HEX.32 6" 1/4" HEX.38 8" 5/16" HEX " 3/8" HEX " 3/8" HEX " 1/2" HEX " 5/8" HEX 14 Open Base Cleats Galvanized Iron 23 Bristol, RI , Elk Grove Village, IL

26 Turnbuckles A B Turnbuckles / Hook Dimensions C D E Turnbuckles/Hook 1/4" /16" /8" /2" /8" /4" /8" " /4" /2" A B Turnbuckles / Eye Dimensions C D E Turnbuckles/Eye 1/4" /16" /8" /2" /8" /4" /8" " /4" /2" /4" " /2" /4" Turnbuckles / Jaw Dimensions A B C D E F G H 1/4" /16" /8" /2" /8" /4" /8" " /4" /2" /4" " /2" /4" Turnbuckles/Jaw 24 M&G Industries, Inc.

27 Stainless Steel Fittings Approx. Weight Each Heavy Duty Wire Rope Thimble / Stainless Steel Type 304 A B C D E 1/4" /16" /8" /2" /8" /4" /8" " /8"-1.1/4" /4"-1.3/8" Heavy Duty Wire Rope Thimble Stainless Steel Type 304 & Type 316 Approx.. Wt. / Ctn. 100 Pcs. Kilograms Standard Wire Rope Thimble / Stainless Steel Type 304 A B C D E 3/32" /8" /32" /16" /4" /32" /16" /32" /2" /16" /8" /16" /8" /8" " Thimbles/Standard Stainless Steel Type 304 Forged 25 Bristol, RI , Elk Grove Village, IL

28 Stainless Steel Fittings Breaking Load Turnbuckle Welded Forks / Stainless Steel 316 Forged Weight in A D L1 L2 L3 3/16" 1, /4" 2, /16" 4, /8" 6, /2" 11, /16" 16, /8" 20, Turnbuckles Welded Forks Stainless Steel Type 316 Forged Breaking Load Turnbuckle Welded Forks / Stainless Steel 316 Forged Weight in A D L1 L2 3/16" 1, /4" 2, /16" 4, /8" 6, /2" 10, /8" 15, Turnbuckles Eye & Eye Stainless Steel Type 316 Forged Breaking Load Turnbuckle Welded Forks / Stainless Steel 316 Forged Weight in A D L1 L2 L3 3/16" 1, /4" 2, /16" 4, /8" 6, /2" 10, /8" 15, Turnbuckles Eye & Hook Stainless Steel Type 316 Forged Breaking Load Turnbuckle Welded Forks / Stainless Steel 316 Forged Weight in A D L1 L2 3/16" 1, /4" 2, /16" 4, /8" 6, /2" 10, /8" 15, Turnbuckles Hook & Hook Stainless Steel Type 316 Forged 26 M&G Industries, Inc.

29 Stainless Steel Fittings (A) (inches) Breaking Load Anchor Shackle / Stainless Steel 316, Screw pin Weight B (mm) H (mm) D (mm) L1 (mm) Body (kgs) Pin (kgs) 5/32" /16" 1, /4" 1, /16" 3, /32" 5, /32" 7,, /2" 11, /16" 12, /8" 13, /4" 18, /8" 21, " 24, Shackles Stainless Steel Type 316 Forged Approx. Weight Each Wire Rope Clips / Stainless Steel Type 316 A (mm) B1 (mm) B2 (mm) B2 (mm) D (mm) H2 (mm) 1 (mm) M M M M M M M M M M M M Wire Rope Clips Stainless Steel Type Bristol, RI , Elk Grove Village, IL

30 Cable & Wire Cutters Wire Rope Cutters For 3/16" Maximum Diameter Cable Note: not for use on heat treated spring wire or music wire. 316 Cable Cutter Tool No. Length Wire Rope Piano Wire Steel Wire ACSR Cable Weight 316 CC 8" 3/16" 9 oz. HWC 6 - Wire Rope Cutters (Felco Type) Heavy Duty Designed for cutting of all soft and hard steel cable or wire rope up to capacity shown HWC 6 - Cable Cutters Tool No. Length Wire Rope Piano Wire Steel Wire ACSR Cable Weight HWC mm 6 mm 2.5 mm 4 mm 250 HWC 9, - HW 12, HWC 16 - Wire Rope Cutters (Felco Type) Heavy Duty Designed for cutting of all soft and hard steel cable or wire rope up to capacity shown Tool No. Length Wire Rope Piano Wire Steel Wire ACSR Cable Weight HWC mm 9 mm 4.0 mm 6 mm H HWC mm 12 mm 4.5 mm 7 mm 58 1,500 HWC mm 5.0 mm 9 mm 120 2,500 HWC 9 - HWC 12 - HWC 16 Cable Cutters RC Wire Rope Cutters (Felco Type) Heavy Duty RC Cable Cutters Tool No. Length Wire Rope Piano Wire Steel Wire ACSR Cable Weight RC " 3/8" 3/8" 3 lbs Swaging Tools HSC Hand Held 5 Cavity Tool with Cutter Designed for Swaging of all cable or wire rope fittings from 1/16" - 1/8" HSC Cable Swager HSC Cable Swager HSC Hand Held 5 Cavity Tool with Cutter Designed for Swaging of all cable or wire rope fittings from 1/16" - 3/16" HSC 600B - Bench Type 5 Cavity Tool with Cutter Designed for Swaging of all cable or wire rope fittings from 1/16" - 3/16" Available in 1 cavity sizes 1/16" - 5/16" HSC 600B - Cable Swager Bench Type 28 Bristol, RI , Elk Grove Village, IL

31 Conversion Tables 1 lb = kg (Kilogram) 1 kg = lbs 1kN (kilonewton) = kg = lbs 1 short ton = 2,000 lbs = kg 1 long ton = 2,240 lbs = 1, kg 1 metric ton = 2, lbs = 1,000 kg 1 ft =.3048 m (meter) 1 m = ft = inches 1 inch = 25.4 mm (millimeter) 1 mm = inches 1 yard =.9144 m 1m = yards 1 mile = km (kilometer) 1 km = miles 1 mile = 1,760 yards = 5,280 ft 1 yard = 3 ft = 36 inches 1 ft. = 12 inches 1 fathom = 6 ft 1lb = 16 ounces 1 kilometer = 1000 meters 1meter = 100 centimeters 1 centimeter = 10 millimeters 1 kilogram = 1000 grams Inches Decimals of an Inch Millimeters Inches Decimals of an Inch Millimeters Inches Decimals of an Inch Millimeters / / / / / / / / / / / / / / / / / / / / / / / / / / / / Bristol, RI , Elk Grove Village, Ill

32 Wire Rope and Cable Fittings 85 Broadcommon Road Bristol, RI Tel Fax Greenleaf Avenue Elk Grove Village, IL Tel Fax