TEST REPORT Page 1 of 9

Transcription

1 TEST REPORT Page 1 of 9 REPORT NUMBER : APPLICANT NAME ADDRESS SAMPLE DESCRIPTION : TURR Sarnikon Metal ve Elektronik San. Tic. Ltd. Şti. Deniz Köşkler Mah. Dr. Sadık Ahmet Cad. No:12/A Avcılar İstanbul TURKEY FAX NO : Attention :Hande Tetik İzci (hande@sarnikon.com) One sample of Aluminium Projector Case DATE IN : 17 December, 2012 DATE OUT : 24 December, 2012 MANUFACTURER S NAME : SARNIKON COUNTRY OF ORIGIN : MODEL NO : COLOR : REQUEST : RESULTS : CONCLUSION : TURKEY PR-79 GRAY RoHS Test was performed on the item. See attachment See attachment The test results relate only to the items tested. The whole and/or the part of this test report shall not be reproduced and shall not be shared with third parties, nor to be used for PR activities without the written permission of INTERTEK Test Hizmetleri A.S. The reported uncertainity is based on a standard uncertainity multiplied by a coverage factor k=2, providing a level of confidence of approximately 95%. The uncertainity evaluation has been carried out in accordance with ISO/IEC and UKAS accreditation requirements. Unless otherwise is specified, all Pass or Fail results are given without uncertainity considered. When uncertainity is taken into account, the result may be borderline. Borderline results need to be re-tested to determine their disposition up to customer s decision. Opinions and interpretations expressed herein are outside the scope of UKAS accreditation. Tests marked (*) in this test report are not included in the UKAS accreditation schedule for this laboratory. Bora Şirinbilek Coordinator Neslihan Sözer Chemical Laboratory Manager * * ssenturk

2 R E S U L T S Page 2 of 9 PARTS DESCRIPTION CONCLUSION Sample 1 ALUMINIUM BOX PASS 2 GREY METAL PART PASS 3 COOLER METAL BODY PASS 4 SMALL SCREW PASS 5 M4 CM SCREW PASS 6 SMALL SCREW PASS 7 M 8 MM SCREW PASS 8 M 6 MM SCREW PASS 9 COVER SILICONE PASS 10 GLASS SILICONE PASS 11 O-RING PASS 12 CABLE CLIPS PASS 13 METAL SHEET PASS 14 GLASS PASS

3 R E S U L T S Page 3 of 9 (A) Test Method Summary Testing Item Result RoHS Limit (ppm) Part 1 Part 2 Part 3 Part 4 Cadmium (Cd) Content ND ND ND ND 0.01 % (100 ppm) Chromium VI (Cr+6) Content (ppm) (for non - metal) NA NA NA NA 0.1 % (1000 ppm) Chromium VI (Cr+6) Content (µg/cm²) (for metal) ND ND ND ND Chromium VI (Cr+6) Result (By spot test on metal) NEGATIVE NEGATIVE NEGATIVE NEGATIVE NEGATIVE Lead (Pb) Content ND ND ND ND 0.1 % (1000 ppm) Mercury (Hg) Content ND ND ND ND 0.1 % (1000 ppm) Flame Retardants 0.1 % (1000 ppm) Polybrominated Biphenyls (PBB) NA NA NA NA Monobromobiphenyl (MonoBB) NA NA NA NA Dibromobiphenyl (DiBB) NA NA NA NA Tribromobiphenyl (TriBB) NA NA NA NA Tetrabromobiphenyl (TetraBB) NA NA NA NA Pentabromobiphenyl (PentaBB) NA NA NA NA Hexabromobiphenyl (HexaBB) NA NA NA NA Heptabromobiphenyl (HeptaBB) NA NA NA NA Octabromobiphenyl (OctaBB) NA NA NA NA Nonabromobiphenyl (NonaBB) NA NA NA NA Decabromobiphenyl (DecaBB) NA NA NA NA Polybrominated Diphenyl Ethers (PBDE) NA NA NA NA Monobromodiphenyl Ether (MonoBDE) NA NA NA NA Dibromodiphenyl Ether (DiBDE) NA NA NA NA Tribromodiphenyl Ether (TriBDE) NA NA NA NA Tetrabromodiphenyl Ether (TetraBDE) NA NA NA NA Pentabromodiphenyl Ether (PentaBDE) NA NA NA NA Hexabromodiphenyl Ether (HexaBDE) NA NA NA NA Heptabromodiphenyl Ether (HeptaBDE) NA NA NA NA Octabromodiphenyl Ether (OctaBDE) NA NA NA NA Nonabromodiphenyl Ether (NonaBDE) NA NA NA NA Decabromodiphenyl Ether (DecaBDE) NA NA NA NA Remarks : (B) Test Method : ppm=parts per million based on dry weight of sample µg/cm²=microgram per square centimetre mg/kg with 50 cm²=milligram per kilogram with 50 square centimetre <=Less than ND =Not detected NA =Not applicable NR =Not requested Testing Item Testing Method Reporting Limit Cadmium (Cd)Content Lead (Pb)Content Mercury (Hg)Content Chromium VI (Cr6+)(For non-metal) With reference to IEC 62321:2008,by alkaline digestion and determined by 1 ppm UV-VIS spectrophotometer Chromium VI (Cr6+)(For metal) With reference to IEC 62321:2008,by SPOT TEST 1 ppm (IN TESTING Chromium VI (Cr6+)(For metal) With reference to IEC 62321:2008,by boiling water extraction and determined by UV-VIS spectrophotometer 0.02 mg/kg with 50 cm² (IN TESTING PBBs/PBDEs With reference to IEC 62321:2008,by solvent extraction and determined by GC/MS and HPLC NOTE : The above limits were quoted from 2002/95/EC and amendment 2005/618/EC for homogeneous material. 5 ppm

4 R E S U L T S Page 4 of 9 (A) Test Method Summary Testing Item Result RoHS Limit (ppm) Part 5 Part 6 Part 7 Part 8 Cadmium (Cd) Content ND ND ND ND 0.01 % (100 ppm) Chromium VI (Cr+6) Content (ppm) (for non - metal) NA NA NA NA 0.1 % (1000 ppm) Chromium VI (Cr+6) Content (µg/cm²) (for metal) ND ND ND ND Chromium VI (Cr+6) Result (By spot test on metal) NEGATIVE NEGATIVE NEGATIVE NEGATIVE NEGATIVE Lead (Pb) Content ND ND ND ND 0.1 % (1000 ppm) Mercury (Hg) Content ND ND ND ND 0.1 % (1000 ppm) Flame Retardants 0.1 % (1000 ppm) Polybrominated Biphenyls (PBB) NA NA NA NA Monobromobiphenyl (MonoBB) NA NA NA NA Dibromobiphenyl (DiBB) NA NA NA NA Tribromobiphenyl (TriBB) NA NA NA NA Tetrabromobiphenyl (TetraBB) NA NA NA NA Pentabromobiphenyl (PentaBB) NA NA NA NA Hexabromobiphenyl (HexaBB) NA NA NA NA Heptabromobiphenyl (HeptaBB) NA NA NA NA Octabromobiphenyl (OctaBB) NA NA NA NA Nonabromobiphenyl (NonaBB) NA NA NA NA Decabromobiphenyl (DecaBB) NA NA NA NA Polybrominated Diphenyl Ethers (PBDE) NA NA NA NA Monobromodiphenyl Ether (MonoBDE) NA NA NA NA Dibromodiphenyl Ether (DiBDE) NA NA NA NA Tribromodiphenyl Ether (TriBDE) NA NA NA NA Tetrabromodiphenyl Ether (TetraBDE) NA NA NA NA Pentabromodiphenyl Ether (PentaBDE) NA NA NA NA Hexabromodiphenyl Ether (HexaBDE) NA NA NA NA Heptabromodiphenyl Ether (HeptaBDE) NA NA NA NA Octabromodiphenyl Ether (OctaBDE) NA NA NA NA Nonabromodiphenyl Ether (NonaBDE) NA NA NA NA Decabromodiphenyl Ether (DecaBDE) NA NA NA NA Remarks : (B) Test Method : ppm=parts per million based on dry weight of sample µg/cm²=microgram per square centimetre mg/kg with 50 cm²=milligram per kilogram with 50 square centimetre <=Less than ND =Not detected NA =Not applicable NR =Not requested Testing Item Testing Method Reporting Limit Cadmium (Cd)Content Lead (Pb)Content Mercury (Hg)Content Chromium VI (Cr6+)(For non-metal) With reference to IEC 62321:2008,by alkaline digestion and determined by 1 ppm UV-VIS spectrophotometer Chromium VI (Cr6+)(For metal) With reference to IEC 62321:2008,by SPOT TEST 1 ppm (IN TESTING Chromium VI (Cr6+)(For metal) With reference to IEC 62321:2008,by boiling water extraction and determined by UV-VIS spectrophotometer 0.02 mg/kg with 50 cm² (IN TESTING PBBs/PBDEs With reference to IEC 62321:2008,by solvent extraction and determined by GC/MS and HPLC NOTE : The above limits were quoted from 2002/95/EC and amendment 2005/618/EC for homogeneous material. 5 ppm

5 R E S U L T S Page 5 of 9 (A) Test Method Summary Testing Item Result RoHS Limit (ppm) Part 9 Part 10 Part 11 Part 12 Cadmium (Cd) Content ND ND ND 23 ppm 0.01 % (100 ppm) Chromium VI (Cr+6) Content (ppm) (for non - metal) ND ND ND NA 0.1 % (1000 ppm) Chromium VI (Cr+6) Content (µg/cm²) (for metal) NA NA NA ND Chromium VI (Cr+6) Result (By spot test on metal) NA NA NA NEGATIVE NEGATIVE Lead (Pb) Content ND ND ND ppm* 0.1 % (1000 ppm) Mercury (Hg) Content ND ND ND ND 0.1 % (1000 ppm) Flame Retardants 0.1 % (1000 ppm) Polybrominated Biphenyls (PBB) ND ND ND NA Monobromobiphenyl (MonoBB) ND ND ND NA Dibromobiphenyl (DiBB) ND ND ND NA Tribromobiphenyl (TriBB) ND ND ND NA Tetrabromobiphenyl (TetraBB) ND ND ND NA Pentabromobiphenyl (PentaBB) ND ND ND NA Hexabromobiphenyl (HexaBB) ND ND ND NA Heptabromobiphenyl (HeptaBB) ND ND ND NA Octabromobiphenyl (OctaBB) ND ND ND NA Nonabromobiphenyl (NonaBB) ND ND ND NA Decabromobiphenyl (DecaBB) ND ND ND NA Polybrominated Diphenyl Ethers (PBDE) ND ND ND NA Monobromodiphenyl Ether (MonoBDE) ND ND ND NA Dibromodiphenyl Ether (DiBDE) ND ND ND NA Tribromodiphenyl Ether (TriBDE) ND ND ND NA Tetrabromodiphenyl Ether (TetraBDE) ND ND ND NA Pentabromodiphenyl Ether (PentaBDE) ND ND ND NA Hexabromodiphenyl Ether (HexaBDE) ND ND ND NA Heptabromodiphenyl Ether (HeptaBDE) ND ND ND NA Octabromodiphenyl Ether (OctaBDE) ND ND ND NA Nonabromodiphenyl Ether (NonaBDE) ND ND ND NA Decabromodiphenyl Ether (DecaBDE) ND ND ND NA Remarks : (B) Test Method : ppm=parts per million based on dry weight of sample µg/cm²=microgram per square centimetre mg/kg with 50 cm²=milligram per kilogram with 50 square centimetre <=Less than ND =Not detected NA =Not applicable NR =Not requested * Lead RoHS limit for brass item is ppm. Testing Item Testing Method Reporting Limit Cadmium (Cd)Content Lead (Pb)Content Mercury (Hg)Content Chromium VI (Cr6+)(For non-metal) With reference to IEC 62321:2008,by alkaline digestion and determined by 1 ppm UV-VIS spectrophotometer Chromium VI (Cr6+)(For metal) With reference to IEC 62321:2008,by SPOT TEST 1 ppm (IN TESTING Chromium VI (Cr6+)(For metal) With reference to IEC 62321:2008,by boiling water extraction and determined by UV-VIS spectrophotometer 0.02 mg/kg with 50 cm² (IN TESTING PBBs/PBDEs With reference to IEC 62321:2008,by solvent extraction and determined by GC/MS and HPLC NOTE : The above limits were quoted from 2002/95/EC and amendment 2005/618/EC for homogeneous material. 5 ppm

6 R E S U L T S Page 6 of 9 (A) Test Method Summary Testing Item Result RoHS Limit (ppm) Part 13 Part 14 Cadmium (Cd) Content ND ND 0.01 % (100 ppm) Chromium VI (Cr+6) Content (ppm) (for non - metal) NA ND 0.1 % (1000 ppm) Chromium VI (Cr+6) Content (µg/cm²) (for metal) ND NA Chromium VI (Cr+6) Result (By spot test on metal) NEGATIVE NA NEGATIVE Lead (Pb) Content ND ND 0.1 % (1000 ppm) Mercury (Hg) Content ND ND 0.1 % (1000 ppm) Flame Retardants 0.1 % (1000 ppm) Polybrominated Biphenyls (PBB) NA NA Monobromobiphenyl (MonoBB) NA NA Dibromobiphenyl (DiBB) NA NA Tribromobiphenyl (TriBB) NA NA Tetrabromobiphenyl (TetraBB) NA NA Pentabromobiphenyl (PentaBB) NA NA Hexabromobiphenyl (HexaBB) NA NA Heptabromobiphenyl (HeptaBB) NA NA Octabromobiphenyl (OctaBB) NA NA Nonabromobiphenyl (NonaBB) NA NA Decabromobiphenyl (DecaBB) NA NA Polybrominated Diphenyl Ethers (PBDE) NA NA Monobromodiphenyl Ether (MonoBDE) NA NA Dibromodiphenyl Ether (DiBDE) NA NA Tribromodiphenyl Ether (TriBDE) NA NA Tetrabromodiphenyl Ether (TetraBDE) NA NA Pentabromodiphenyl Ether (PentaBDE) NA NA Hexabromodiphenyl Ether (HexaBDE) NA NA Heptabromodiphenyl Ether (HeptaBDE) NA NA Octabromodiphenyl Ether (OctaBDE) NA NA Nonabromodiphenyl Ether (NonaBDE) NA NA Decabromodiphenyl Ether (DecaBDE) NA NA Remarks : (B) Test Method : ppm=parts per million based on dry weight of sample µg/cm²=microgram per square centimetre mg/kg with 50 cm²=milligram per kilogram with 50 square centimetre <=Less than ND =Not detected NA =Not applicable NR =Not requested Testing Item Testing Method Reporting Limit Cadmium (Cd)Content Lead (Pb)Content Mercury (Hg)Content Chromium VI (Cr6+)(For non-metal) With reference to IEC 62321:2008,by alkaline digestion and determined by 1 ppm UV-VIS spectrophotometer Chromium VI (Cr6+)(For metal) With reference to IEC 62321:2008,by SPOT TEST 1 ppm (IN TESTING Chromium VI (Cr6+)(For metal) With reference to IEC 62321:2008,by boiling water extraction and determined by UV-VIS spectrophotometer 0.02 mg/kg with 50 cm² (IN TESTING PBBs/PBDEs With reference to IEC 62321:2008,by solvent extraction and determined by GC/MS and HPLC NOTE : The above limits were quoted from 2002/95/EC and amendment 2005/618/EC for homogeneous material. 5 ppm

7 R E S U L T S Page 7 of 9 Part 1 Part 2 Part 3 Part 4

8 R E S U L T S Page 8 of 9 Part 5 Part 6 Part 7 Part 8 Part 9 Part 10

9 R E S U L T S Page 9 of 9 Part 11 Part 12 Part 13 Part 14 ## END OF TEST REPORT ##