Polycom Conference Link Quick Reference Guide

Transcription

1 co de cs X ta Ce ble ilin m ic g a Re mic rra y alp ro ph s r o Re ese alp nc ne a e rra r ys So esen Gro ce up ds co G So tru rou de cs c p ds ture tab ta le tio m n ics IP 0 00 HDX codecs HDX table mic arrays Ceiling microphone arrays codecs table mics HD HD X Conference Link is a digital interface used to connect Polycom equipment together to share audio and control information. This table shows the types of devices that may be connected together using Conference Link. There are different Conference Link cables and different connectors depending on the application of the cable. The following table shows the different Conference Link cables that are available. SKU Connector Connector Connector Connector Type Drawing Drawing Type Length ft (.m) Notes Cable - Console Interconnect Cable for SodStation IP 000, ft/.m CLink cable with Walta to Walta connectors. Connects two () consoles together. Cross-over cable. Cable - HDX microphone array cable, Walta to Walta connectors, 0ft/m. Connects an HDX microphone to an HDX microphone or to. This SKU includes the cable listed below. Cross-over cable ft (m) --00 ft (.m) Used with HDX HDX 000 and the HDX table microphone arrays. Also for use with the SodStation IP 000 and HDX table microphone arrays. Cross-over cable ft (.m) Included with the HDX table microphone arrays. Cross-over cable. ft (.m) Series microphone array cable. Connects Group Series microphone to Group Series microphone or Group Series microphone to Group Series codec. Not compatible with HDX table microphone array due to different overmold. Cross-over cable. in (0.m) Included with the device. Cross-over cable for connecting Clink between devices such as and series codec. in (0.m) Dongle for connecting HDX table microphone array to or series codec. Typically included with the series video systems. Straight-thru cable Walta female ft (.m) Part of the primary Ceiling Microphone Array package. Cross-over cable for connecting Clink between devices. Typically used between and the first Ceiling Microphone Array ft (.m) Part of the extension Ceiling Microphone Array package. Cross-over cable for connecting CLink between devices. Typically used between Ceiling Microphone Arrays ft (0.m) ft (m) Cross-over cable for connecting Clink between devices. Typically used between and the first Ceiling Microphone Array. Straight-through cable that is part of the Ceiling Microphone Array package. Must be used with a cross-over cable for proper operation RJ female in (0.m) Dongle for connecting Ceiling Microphone Array or other RJ- CLink cable to HDX 000/000/000 series codecs. Included with primary Ceiling Microphone Array. Straight-thru cable ft (m) CLink cable, HDX microphone array cable. Walta to Walta. 0 ft/m. Connects HDX microphone to HDX microphone/sodstation IP ft (.m) CLink cable, HDX microphone array cable. Walta to Walta. 0 ft/m. Connects HDX microphone to HDX microphone/sodstation IP000. October 0 Page

2 Series --00 (ft /.m) --00 (ft /.m) --00 (in / 0.m) --00 (in / 0.m) (ft /.m) (0ft /.m) (00ft / 0.m) (0ft / m) --00 (ft /.m) --00 (ft /.m) (0ft /.m) --00 (in / 0.m) --00 (in / 0.m) (ft /.m) (0ft /.m) (00ft / 0.m) --00 (ft /.m) --00 (ft /.m) (0ft /.m) --00 (ft /.m) Page

3 HDX Series and HDX 000 to HDX (0ft / m) --00 (ft /.m) --00 (ft /.m) (0ft / m) --00 (ft /.m) --00 (ft /.m) --00 (in / 0.m) or (0ft / m) --00 (ft /.m) --00 (ft /.m) (0ft /.m) (ft /.m) (0ft /.m) (00ft / 0.m) --00 (in / 0.m) --00 (in / 0.m) (ft /.m) (0ft /.m) (00ft / 0.m) HDX 000 to HDX (in / 0.m) --00 (in / 0.m) (ft /.m) (0ft /.m) (00ft / 0.m) (0ft / m) --00 (ft /.m) --00 (ft /.m) (0ft /.m) --00 (in / 0.m) HDX 000 to HDX (in / 0.m) (ft /.m) (0ft /.m) (00ft / 0.m) Page

4 HDX Series and (ft /.m) (0ft /.m) (00ft / 0.m) or (0ft / m) Wall Plate (ft /.m) (0ft /.m) (00ft / 0.m) (ft /.m) --00 (in / 0.m) (0ft / m) --00 (ft /.m) --00 (ft /.m) (0ft /.m) HDX 000 to HDX (0ft / m) --00 (ft /.m) --00 (ft /.m) (0ft /.m) --00 (ft /.m) --00 (ft /.m) (ft /.m) (Note: Multi-interface module required to link two s) --00 (ft /.m) --00 (ft /.m) (ft /.m) --00 (ft /.m) Page

5 Cable Pin Outs Conference Link Cross-Over Cable (shielded). Shielded cable recommended for lengths over ft (.m). Conference Link Cross-Over Cable (shielded). Unshielded cable recommended for lengths of ft (.m) or less. P P AWG P COLOR WHITE/GREEN GREEN WHITE/ORANGE ORANGE WHITE/BROWN BROWN DRAIN WIRE SHIELD SHELL P SHELL P P AWG COLOR WHITE/GREEN GREEN WHITE/BLUE BLUE WHITE/ORANGE ORANGE WHITE/BROWN BROWN P P --00 (in / 0.m) (ft /.m) (0ft /.m) (00ft / 0.m) Length Limitations <= ft /.m or to 00ft to ft to ft to ft <= ft /.m <= ft /.m to ft to 00ft to 00ft to ft While not common, there are applications, such as room-combining, where both Conference Link ports on can be used to meet the length requirements to the first microphone array. Page

6 Microphone Array Support Device # mic arrays supported C C C HDX 000 HDX 000 HDX 000 HDX Up to microphone arrays can be used with each devices, but the number of microphone elements supported on a C is limited to microphone elements. Multiple devices can be linked together with OBAM to support more than microphone arrays Multiple devices can be linked together with OBAM to support more than microphone arrays HDX 00 supports mic arrays. Adding one or more devices connected over Conference Link increases the number of mic arrays that can be used to the limit of the device(s). Two analog expansion microphones are supported. One additional microphone array is supported when used with Group Series codecs, and two additional microphone arrays are supported on HDX codecs. So ds Number of Microphone arrays supported when connecting devices with Conference Link. tru ct HD ur X ec Se rie s Re alp re se nc So eg ro ds up ta Se tio rie n s IP 0 00 Notes C HDX Series Series --00 Notes: Adding more s increases the maximum number of mic arrays. A Multi-Interface module is required for ( for NA). Page