Paetec SIP Configuration Guide The missing manual
|
|
- Tyler Lewis
- 8 years ago
- Views:
Transcription
1 Paetec SIP Configuration Guide The missing manual By: Alex Hannah CCIE Voice # /9/2010 Abstract: This document will go over the IOS Gateway configuration and CUCM configuration to connect a Cisco CUBE to Paetec s Broadsoft or G9 SBC platform. This serves as the missing manual and was crafted from the internal resources of TBL UC Engineering. Please DO NOT share with anyone other than TBL Staff.
2 1. IOS CUBE ( Cisco Unified Border Element ) Configuration is required in order to get the CUBE talking to the SBC in the Paetec Cloud. This section will list out the configuration necessary for the Broadsoft SBC switch as well as the differences for the G9 platform. Configuration was taken from a production MPLS and SIP Trunk 3845 for C&F Bank running IOS version T5 Advanced Enterprise Services c3845-adventerprisek9-mz t5.bin ***Manditory commands are in bold face. Last configuration change at 12:47:10 EDT Fri May by tbluser NVRAM config last updated at 12:47:40 EDT Fri May by tbluser version 12.4 service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone service password-encryption hostname HQ-3845-MPLS-DS3 boot-start-marker boot-end-marker card type t3 1 logging message-counter syslog logging buffered informational enable secret 5 $1$hFUl$M2UB5IwB3T5Tk24Zzlpoj/ enable password B362F2F aaa new-model aaa authentication login default group radius local-case aaa authentication login local-case group radius aaa authentication ppp network local-case aaa session-id common clock timezone EST -5 clock summer-time EDT recurring dot11 syslog ip source-route ip cef
3 ip domain name candfbank.local ip multicast-routing no ipv6 cef multilink bundle-name authenticated voice-card 0 no dspfarm dsp services dspfarm voice service voip allow-connections h323 to h323 ( Optional if H323 is used ) allow-connections h323 to sip ( Optional if H323 is used ) allow-connections sip to h323 ( Optional if H323 is used ) allow-connections sip to sip no supplementary-service sip moved-temporarily fax protocol pass-through g711ulaw no fax-relay sg3-to-g3 h323 modem passthrough nse codec g711ulaw sip bind control source-interface Serial1/0 bind media source-interface Serial1/0 header-passing error-passthru outbound-proxy ipv4: early-offer forced midcall-signaling passthru voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw ( IF Diversion Headers are required ) by Broadsoft or for SnR Functionality voice class sip-profiles 101 request ANY sip-header Allow-Header modify ", UPDATE" "" response ANY sip-header Allow-Header modify ", UPDATE" "" request INVITE sip-header Diversion add "Diversion: <sip: @ >;privacy=off;screen=no" request INVITE sip-header Diversion add "Diversion: <sip: @ >;privacy=off;screen=no"
4 voice translation-rule 2 rule 1 /^18...$/ / / voice translation-rule 3 rule 1 /^8/ // voice translation-profile OutboundRedirecting translate called 3 translate redirect-called 2 crypto pki trustpoint TP-self-signed enrollment selfsigned subject-name cn=ios-self-signed-certificate revocation-check none rsakeypair TP-self-signed crypto pki certificate chain TP-self-signed certificate self-signed F B8 A D0609 2A F70D F30 2D F532D 53656C66 2D E65642D D E 170D A17 0D A F302D F532D53 656C662D E 65642D D F 300D0609 2A F70D D CD92 33BF263C 5ECF9865 FF7BF70F ED3E913C 5CFC3636 E6FAAD78 08D B6E5B16 9E912B57 BA0D52F A2 2D D2EC30C8 4E9B3128 A04B5B98 DA4A3A9E 66CE133C 10326CEC 04CF6A05 D2F490E2 193D8717 C B661 5D51192A 84B7E19A B2E45163 ABCBC4A6 F700E589 0C188BF8 6CB7C861 D822B20A 9ED A F D FF FF D1104 1B F75 726E616D 652E796F F 6D61696E 2E636F6D 301F D B3296 A964F2D1 3C001BB3 AE190ECD 9FCD32E0 4D301D D0E B3296A9 64F2D13C 001BB3AE 190ECD9F CD32E04D 300D0609 2A F70D A6 C39BD A2ABE 213B7C49 A746D00C 71AC53AF C66AE596 9D6FA84F E1 9710E1D4 C8A9B4CF 0FBD254B F9F33415 F0515D4E 0AAB136D CC E3E52767 F560D19F 003BC59E 753C19DE C7197FFD 1D1CDB3B 73CB5B7C BB1B22D3 188CA3EA 24E98207 B4079A05 8A43B883 87D6E601 E3362C34 AD9D quit
5 memory free low-watermark processor memory free low-watermark IO username c&f1td3partm3nt privilege 15 secret 5 $1$k2HU$vA5Z74H8ihOrhopd3cuYJ1 username paetec secret 5 $1$pvw6$Zgu.1lNl8DpgwZwLHMPAc0 archive log config hidekeys controller T3 1/0 clock source line description PaeTec - MPLS - Circuit ID: 19.HFGS COXC COX PID: PaeTec: PON# ip telnet source-interface GigabitEthernet0/1 ip ftp source-interface GigabitEthernet0/0 ip ssh source-interface GigabitEthernet0/1 class-map match-any VOICE-CTRL-LAN match ip dscp af21 class-map match-all VOICE match ip dscp ef class-map match-any VOICE-CTRL match ip dscp af31 match ip dscp cs3 policy-map LAN-EDGE class VOICE set ip dscp ef class VOICE-CTRL-LAN set ip dscp cs3 policy-map WAN-EDGE class VOICE priority set ip dscp ef class VOICE-CTRL bandwidth 2000 set ip dscp af21 interface Loopback0
6 ip address no ip redirects no ip unreachables ip pim sparse-dense-mode ip virtual-reassembly interface GigabitEthernet0/0 description Stonehouse LAN ip address no ip redirects no ip unreachables ip flow ingress ip flow egress ip pim sparse-dense-mode duplex auto speed auto media-type rj45 service-policy output LAN-EDGE interface GigabitEthernet0/1 description Unused Port no ip address shutdown duplex auto speed auto media-type rj45 interface Serial1/0 ip address ip flow ingress ip flow egress encapsulation ppp dsu bandwidth service-policy output WAN-EDGE router eigrp 100 redistribute connected redistribute bgp metric route-map FILTER-BGP2 network network no auto-summary router bgp no synchronization bgp log-neighbor-changes bgp suppress-inactive redistribute eigrp 100 neighbor remote-as default-information originate no auto-summary
7 ip forward-protocol nd no ip http server no ip http secure-server ip flow-export source GigabitEthernet0/0 ip flow-export version 5 ip flow-export destination logging trap debugging logging access-list 10 permit access-list 10 permit access-list 10 permit access-list 10 permit access-list 10 deny any snmp-server community tech1st RO snmp-server community Rtr1927 RO snmp-server enable traps tty route-map FILTER-BGP2 permit 10 match ip address 10 route-map FILTER-BGP permit 10 match ip address 10 radius-server host auth-port 1645 acct-port 1646 radius-server key D E731F control-plane call threshold global cpu-avg low 68 high 75 call threshold global total-mem low 75 high 85 call threshold global total-calls low 35 high 40 sccp local GigabitEthernet0/0 sccp ccm identifier 2 version sccp ccm identifier 1 version sccp sccp ccm group 1
8 associate ccm 2 priority 1 associate ccm 1 priority 2 associate profile 2 register XCODE0180_SIP associate profile 1 register CFB0180_SIP dspfarm profile 2 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 15 associate application SCCP dspfarm profile 1 conference codec g711ulaw codec g729br8 codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 2 associate application SCCP dial-peer voice 200 voip description To CUCM Sub for DID Ranges to 3079 preference 1 destination-pattern voice-class codec 1 no voice-class sip outbound-proxy session protocol sipv2 session target ipv4: dtmf-relay rtp-nte no vad dial-peer voice 201 voip description To CUCM Pub for DID Ranges to 3079 preference 2 destination-pattern voice-class codec 1 no voice-class sip outbound-proxy session protocol sipv2 session target ipv4: dtmf-relay rtp-nte no vad dial-peer voice 100 voip description Inbound from Paetec SIP voice-class codec 1
9 session protocol sipv2 session target sip-server incoming called-number $ dtmf-relay rtp-nte no vad dial-peer voice 202 voip description Inbound from CUCM incoming called-number. dial-peer voice 102 voip description Local Dial Peer translation-profile outgoing OutboundRedirecting destination-pattern 8[2-9]...$ progress_ind setup enable 3 progress_ind connect enable 8 session protocol sipv2 session target sip-server session transport udp dtmf-relay rtp-nte dial-peer voice 103 voip description Long Distance Peer translation-profile outgoing OutboundRedirecting destination-pattern 81[2-9]..[2-9]... progress_ind setup enable 3 progress_ind connect enable 8 session protocol sipv2 session target sip-server session transport udp dtmf-relay rtp-nte no vad dial-peer voice 101 voip description 911 translation-profile outgoing OutboundRedirecting destination-pattern 911 progress_ind setup enable 3 progress_ind connect enable 8 session protocol sipv2 session target sip-server session transport udp dtmf-relay rtp-nte dial-peer voice 104 voip description Services translation-profile outgoing OutboundRedirecting destination-pattern [2-9]11 progress_ind setup enable 3 progress_ind connect enable 8
10 session protocol sipv2 session target sip-server session transport udp dtmf-relay rtp-nte NEXT SECTION DEPENDS ON IF CONNECTING TO BROADSOFT VS G9 PAY CLOSE ATTENTION TO SIP-UA IT MAKES ALL THE DIFFERENCE PAETEC BROADSOFT WEST SWITCH CONFIG, REQUIRES AUTHENTICATION sip-ua credentials username password C252B0A realm none authentication username password E no remote-party-id retry invite 2 retry register 10 timers connect 100 registrar dns: expires 3600 sip-server dns: host-registrar PAETEC G9 SWITCH CONFIG, REQUIRES NO AUTHENTICATION sip-ua no remote-party-id retry invite 2 retry register 10 timers connect 100 sip-server dns: host-registrar banner motd ^CThis is a proprietary system, NOT for public or personal use. This system is actively monitored and accessed by C&F Bank. By logging onto this system, the user consents to such monitoring and access. All work products, communications, files, data or information directly or indirectly created, inputted or accessed on this system are and shall become the sole property of C&F Bank. USE OF THIS SYSTEM WITHOUT OR IN EXCESS OF THE PROPER AUTHORIZATION MAY SUBJECT THE USER TO DISCIPLINE AND/OR CIVIL AND CRIMINAL PENALTIES.^C line con 0 password 7 143A1D0E55166C0A30 logging synchronous
11 transport preferred telnet transport output all line aux 0 transport preferred telnet transport output all line vty 0 4 exec-timeout 60 0 privilege level 15 password 7 013E E35 logging synchronous transport preferred telnet transport input all transport output all line vty 5 15 exec-timeout 60 0 privilege level 15 password 7 013E E35 logging synchronous transport preferred telnet transport input all transport output all scheduler allocate ntp server end
12 2. Cisco Unified Communications Manager Configuration: This section will show screenshots and brief descriptions of what is necessary on CUCM to connect to the CUBE and place an outbound call using Paetec DynSIP solution. A SIP Trunk is required to connect to the CUBE, which can be configured under DEVICE > TRUNK in CUCM, select SIP Trunk. Details on the SIP Trunk can be seen in the following screen shots: ( Key things are DP, MRGL is optional b/c it inherits from DP, but I was lazy, Location, NO MTP is required, redirect diversion header for both outbound and inbound are checked, Destination IP ( CUBE IP ), DTMF type, and SIP Trunk security profile ).
13
14 SIP Trunk Security Profile: Make SURE the SIP Trunk Security Profile in CUCM is left at a default minimum level, this bit me hard the first go around with SIP Trunking, also ensure the bottom 4 check boxes are enabled.
15 3. Call Routing: This section will go over the standard concepts of Route Group, Route List, Route Patterns to show the call routing for sample SIP Configuration. Route Group: Route List:
16 Route Patterns: *** Note: All the normal patterns we would enable or Route Filters for outbound calling will point to the SIP Trunk Route List. Nothing new here. 4. Device Pool Settings ( Used for the device pool section under the SIP Trunk ) Import items are Region ( MUST BE G729 EVERYWHERE ), MRGL, Location.
17 Regions: G.729 must be enabled everywhere 5. Media Resource: Make sure to include the Hardware based XCODE and CFB we configured in the IOS section
18
19 6. Broadsoft West Security Settings with CUCM: Make sure to configure a Application User for the BTN in CUCM, used with security Digest Authentication on the CUCM. I Believe this is optional, but don t chance it
and 2, implemented With Cisco Unified Border Control Element (CUBE)
www.xo.com XO SIP Service Customer Configuration Guide for Cisco Unified Communications Manager (CUCM) 8.0.3 XO SIP Packages 1 and 2, implemented With Cisco Unified Border Control Element (CUBE) 1 PRODUCT
More informationSIP Trunking Configuration Guide for Cisco Unified Communications Manager (CUCM) Version 9.0.1.11005-1 with Cisco Unified Border Element (CUBE)
SIP Trunking Configuration Guide for Cisco Unified Communications Manager (CUCM) Version 9.0.1.11005-1 with Cisco Unified Border Element (CUBE) Table of Contents Introduction... 3 Executive Summary..3
More informationMotorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration
Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration Summary This setup covers the of the TEAM VoWLAN solution with a Cisco Communications Manager Express 4.1 +. This integration
More informationIDT / Net2phone SIP Trunking Configuration Guide for Cisco Business Edition 3000 (BE3000) Release 8.6.4 with Cisco Unified Border Element Release 8.8.
Application Notes IDT / Net2phone SIP Trunking Configuration Guide for Cisco Business Edition 3000 (BE3000) Release 8.6.4 with Cisco Unified Border Element Release 8.8. May 31, 2013 Eric Cimino IDT Corporation
More informationEarthLink Business SIP Trunking. Cisco Call Manager and Cisco CUBE Customer Configuration Guide
EarthLink Business SIP Trunking Cisco Call Manager and Cisco CUBE Customer Configuration Guide Publication History First Release: Version 2.0 April 20, 2012 CHANGE HISTORY Version Date Change Details Changed
More informationEarthLink Business SIP Trunking. Cisco CUCM 9.1 with CUBE Customer Configuration Guide
m EarthLink Business SIP Trunking Cisco CUCM 9.1 with CUBE Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed
More informationQuality of Service and Bandwidth Management Configuration
Quality of Service and Bandwidth Management Configuration This topic provides a reference configuration for Quality or Service (QoS) and bandwidth management using RSVP within a Cisco Unified Communications
More informationCisco ISDN PRI to SIP Gateway
Cisco ISDN PRI to SIP Gateway Supported features Full ISDN E1 emulation Early media support Inbound calling. Type SIP REGISTERED TRUNK Outbound Calling ISDN PRI equivalent Secure Calling via SIP Encrypt
More informationVerizon IP Trunking Service: Connecting Cisco Unified Communications Manager 6.1(2) via the Cisco Unified Border Element using SIP
Application Note Verizon IP Trunking Service: Connecting Cisco Unified Communications Manager 6.1(2) via the Cisco Unified Border Element using SIP October 27, 2008 Table of Contents Introduction... 2
More informationLab Configuring Syslog and NTP (Instructor Version)
(Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
More informationCisco CCA Tool SIP Security methods
Cisco CCA Tool SIP Security methods The Cisco CCA tool (Cisco Configuration Assistant) provides a graphical interface for configuring the UC500 series devices. Once settings have been established using
More informationCisco IOS SIP Configuration Guide
Cisco IOS SIP Configuration Guide Dialpeer Configuration Session Number 1 Terminology Call - A connection terminating on or passing through a gateway. Call Leg - The segment of a call associated with a
More informationSprint SIP Toll Free: Connecting Cisco Unified Customer Voice Portal 8.5 via the Cisco Unified Border Element 8.8 using SIP
Application Note Sprint SIP Toll Free: Connecting Cisco Unified Customer Voice Portal 8.5 via the Cisco Unified Border Element 8.8 using SIP Nov 6, 2012 Table of Contents Introduction... 3 Network Topology...
More informationBrest. Backup : copy flash:ppe_brest1 running-config
Brest Backup : copy flash:ppe_brest1 running-config Cisco SF300-08 Mise en place des services : - Serveurs : 10.3.50.0/24 VLAN 2 (port 1) - DSI : 10.3.51.0/24 VLAN 3 (port 2) - Direction : 10.3.52.0/24
More informationADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability
6AOSSG0007-42A March 2013 Interoperability Guide ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability
More informationCisco Unified Communications Manager 9.1.2 with Cisco Unified Border Element 10.0.1 (IOS 15.4(2)T) using SIP
Application Note COX SIP Trunking: Cisco Unified Communications Manager 9.1.2 with Cisco Unified Border Element 10.0.1 (IOS 15.4(2)T) using SIP May 06, 2014 Page 1 of 58 Table of Contents Introduction...
More informationLevel 3 SIP Trunking: Connecting Cisco Unified Communications Manager 7.1(3) via the Cisco Unified Border Element using SIP
Application Note Level 3 SIP Trunking: Connecting Cisco Unified Communications Manager 7.1(3) via the Cisco Unified Border Element using SIP August 19, 2010 Table of Contents Introduction... 2 Network
More informationIntelepeer SIP Trunking: Connecting Cisco Unified Communications Manager 8.5(1) via the Cisco Unified Border Element 1.3 using SIP
Application Note Intelepeer SIP Trunking: Connecting Cisco Unified Communications Manager 8.5(1) via the Cisco Unified Border Element 1.3 using SIP March 25, 2011 Table of Contents Introduction... 2 Network
More informationIntegra Telecom SIP Trunking: Connecting Cisco Unified Communications Manager 8.5(1) via the Cisco Unified Border Element using SIP
Application Note Integra Telecom SIP Trunking: Connecting Cisco Unified Communications Manager 8.5(1) via the Cisco Unified Border Element using SIP June 3, 2011 Table of Contents Introduction... 2 Network
More informationCisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.
Application Note Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.323 Gateway Introduction This document describes the interoperability
More informationConfiguring Modem Transport Support for VoIP
Configuring Modem Transport Support for VoIP This chapter explains how to configure modem transport support for Voice over IP (VoIP) and contains the following sections: Modem Transport Support Overview,
More informationConfiguring Fax Pass-Through
Configuring Fax Pass-Through This chapter describes the configuration of fax pass-through. With fax pass-through, modulated fax information from the PSTN is passed in-band over a voice speech path in an
More informationSimple MPLS network topology for Dynamips/Olive
Simple MPLS network topology for Dynamips/Olive R1 version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname R1 boot-start-marker
More informationCS3695/M6-109 Lab 8-NPS02 VOIP Sniffing Ver. 8 Rev. 0
Background For this lab, we will be analyzing some Wireshark capture files that were captured using the ARP Poisoning technique on Cisco VIOP (Voice Over IP) phones As this lab took special equipment (i.e.
More informationCisco Unified Communications Manager 10.5.2 with Cisco Unified Border Element [CUBE 11.0.0 IOS-XE 3.15] on ISR 4K using SIP
Verizon SIP Trunking: Cisco Unified Communications Manager 10.5.2 with Cisco Unified Border Element [CUBE 11.0.0 IOS-XE 3.15] on ISR 4K using SIP JULY 24, 2015 Page 1 of 63 Table of Contents Introduction...
More informationApplication Note. December 2014 Table of Contents
Application Note Bell Canada SIP Trunking Service: Connecting Cisco Unified Communications Manager 10.5 via the Cisco Unified Border Element 10.5 [IOS 15.4(3)M] using SIP December 2014 Table of Contents
More informationCenturyLink SIP Trunking: Connecting Cisco Unified Communications Manager 8.6.1 via the Cisco Unified Border Element 8.6 using SIP
Application Note CenturyLink SIP Trunking: Connecting Cisco Unified Communications Manager 8.6.1 via the Cisco Unified Border Element 8.6 using SIP March 22, 2013 Table of Contents Introduction... 2 Network
More informationFeb, 2015. Note: Testing was conducted in tekvizion Labs.
COLT Communications SIP Trunking: Connecting Cisco Unified Communications Manager (CUCM) 10.5.1 via the Cisco Unified Border Element (CUBE) 10.5 using SIP Feb, 2015 Page 1 of 37 Note: ing was conducted
More informationSchools Configuration Files Guide
This document, contains the network diagram, and a list of all the platforms and software releases which were validated for the Schools Service Ready Architecture (SRA). The last section includes the configurations
More informationBusiness Talk IP (France and International) connecting:
Application Note Orange Business Services Business Talk IP (France and International) connecting: Cisco Unified Communications Manager 9.1 with facultative Cisco Unified Border Element 9.0 (IOS 15.2(4)M)
More informationNetwork Diagram Scalability Testbed and Configuration Files
APPENDIX A Network Diagram Scalability Testbed and Configuration Files This appendix contains configurations that were used during a V 3 PN performance and scalability evaluation based on the network illustrated
More informationLab 3.3 Configuring QoS with SDM
Lab 3.3 Configuring QoS with SDM Learning Objectives Configure Quality of Service tools with the SDM QoS wizard Monitor traffic patterns using the SDM QoS interface Topology Diagram Scenario Cisco Security
More informationThe Cisco IOS Firewall feature set is supported on the following platforms: Cisco 2600 series Cisco 3600 series
Cisco IOS Firewall Feature Set Feature Summary The Cisco IOS Firewall feature set is available in Cisco IOS Release 12.0. This document includes information that is new in Cisco IOS Release 12.0(1)T, including
More informationHow To Configure A Cisco Vpn On A Cell Phone With A Pkv On A Safd On A Pv On An Asda On A Network With A Network On A Pc Or Ipv On The Ipv (Svv
CHAPTER 17 The Cisco VPN Client for Cisco Unified IP Phones adds another option for customers attempting to solve the remote telecommuter problem by complementing other Cisco remote telecommuting offerings.
More informationEjemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router
Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue este capítulo Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue el libro completo
More informationApplication Note. Note: Testing was conducted in Verizon lab. May 10, 2011 - Initial Version Table of Contents
Application Note Verizon IP Trunking and IP Contact Center Services: Connecting Cisco Unified Communications Manager 8.0.3 with Cisco Unified Border Element 8.5 (Enterprise Edition) May 10, 2011 - Initial
More informationnexvortex Setup Guide
nexvortex Setup Guide CISCO UC500 March 2012 Introduction This document is intended only for nexvortex customers and resellers as an aid to setting up the Cisco PBX software to connect to the nexvortex
More informationVirtual Private Network Setup
This chapter provides information about virtual private network setup. Virtual Private Network, page 1 Devices Supporting VPN, page 2 Set Up VPN Feature, page 2 Complete Cisco IOS Prerequisites, page 3
More informationTime Warner Cable Business Class (TWCBC):
Application Note Time Warner Cable Business Class (TWCBC): Connecting Cisco Unified Communications Manager 10.5.1/Business Edition 6000 with Cisco Unified Border Element [CUBE 10.5.0] - (IOS 15.4(3) M1)
More informationNetwork Scenarios Pagina 1 di 35
Network Scenarios Pagina 1 di 35 Table of Contents Network Scenarios Cisco 827 s Network Connections Internet Access Scenarios Before You Configure Your Internet Access Network Replacing a Bridge or Modem
More informationValidated Integrations: CUCM 10.x with xic version 4.0 SU-6 (support included for all 4.0 SU s) Version 4.08
IC 4.0 SIP INTEGRATION TO CISCO UNIFIED COMMUNICATIONS MANAGER 10.X Validated Integrations: CUCM 10.x with xic version 4.0 SU-6 (support included for all 4.0 SU s) INTEGRATION DOCUMENT Version 4.08 7601
More informationMicrosoft Lync 2013 [v5.0.8308.0] to Verizon Business SIP Trunk via the Cisco Unified Border Element 10.5 [IOS 15.4(3)M]
Application Note Microsoft Lync 2013 [v5.0.8308.0] to Verizon Business SIP Trunk via the Cisco Unified Border Element 10.5 [IOS 15.4(3)M] 12/12/2014 Table of Contents Introduction... 2 Network Topology...
More informationSkills Assessment Student Training (Answer Key)
CCNA: Connecting Networks Skills Assessment Student Training (Answer Key) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Assessment
More informationAvaya one-x Quick Edition Interoperability with Cisco Integrated Services Router (ISR) SIP Gateway - Issue 1.0
Avaya Solution & Interoperability Test Lab Avaya one-x Quick Edition Interoperability with Cisco Integrated Services Router (ISR) SIP Gateway - Issue 1.0 Abstract Avaya one-x Quick Edition R3.1 provides
More informationLab 7: Firewalls Stateful Firewalls and Edge Router Filtering
Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering 7.1 Details Aim: Rich Macfarlane The aim of this lab is to introduce the concepts of stateful firewalls, using Cisco Contextbased Access Control
More informationEnabling Management Protocols: NTP, SNMP, and Syslog
SECTION 7 Enabling Management Protocols: NTP, SNMP, and Syslog In this Section This section describes how to enable basic management protocols on a Cisco AS5800 and Cisco AS5300 as part of a dial access
More informationCase Study 1: Registering IP Phones with a remote Call
Case Study 1: Registering IP Phones with a remote Call Manager Objectives Place calls from IP Phones under R1 to IP Phones under R2 Place calls from any IP Phone (under R1 and under R2) to the regular
More informationCisco CME SIP Trunk Configuration
Cisco CME SIP Trunk Configuration There are lots of example configurations on the Internet that illustrate how to connect CME to SIP trunks. Few offered any insight as to the reason for the commands that
More information!! Last configuration change at 15:00:48 gmt Thu Oct 11 2012 by admin! NVRAM config last updated at 03:07:42 gmt Wed Nov 14 2012 by admin!
Last configuration change at 15:00:48 gmt Thu Oct 11 2012 by admin NVRAM config last updated at 03:07:42 gmt Wed Nov 14 2012 by admin version 12.2 no service pad service timestamps debug datetime msec
More informationConfiguring Voice and Data Support on VWIC3s
First Published: July 21, 2010, OL-22847-01 This module describes how to configure voice and data support on the next generation of voice/wan Interface Cards (VWICs) also known as VWIC3s. The following
More informationOne-Step Lockdown with Cisco SDM
One-Step Lockdown with Cisco SDM Router Hardening Automagically The process of turning off unnecessary services is called hardening a router to prevent attacks or exploits. The basic steps of router hardening
More informationInteroperability Configuration Guide. SIP Trunking Configuration Guide for Cisco Unified Communications 500 Series
SIP Trunking Configuration Guide for Cisco Unified Communications 500 Series Version 1.0 May 2008 1 Table of Contents 1 Overview...3 2 PAETEC SIP Trunking Service Features...4 3 Sample Customer Premise
More informationSupporting Document LNS Configuration
Supporting Document LNS Configuration Swisscom (Schweiz) AG Version 1-0 15.112010 Inhalt 1 General... 3 1.1 Appendix A: Load Balancing between POPs... 3 1.2 Appendix B: Examples of LNS and BGP Configurations...
More informationConfiguring SIP Registration Proxy on Cisco UBE
The Support for SIP Registration Proxy on Cisco UBE feature provides support for sending outbound registrations from Cisco Unified Border Element (UBE) based on incoming registrations. This feature enables
More informationSecure Network Foundation Implementation Guide for Single Site Deployments
Implementation Guide for Single Site Deployments This document provides a simple vision for a smart and secure business where everyday communications are made easier, faster, and more efficient. Cisco
More informationHow To Configure A Cisco Router With A Cio Router
CHAPTER 1 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
More informationVirtual Fragmentation Reassembly
Virtual Fragmentation Reassembly Currently, the Cisco IOS Firewall specifically context-based access control (CBAC) and the intrusion detection system (IDS) cannot identify the contents of the IP fragments
More informationAPNIC Members Training Course Security workshop. 2-4 July, 2008. Port Vila Vanuatu. In conjunction with PACNOG 4
APNIC Members Training Course Security workshop 2-4 July, 2008 Port Vila Vanuatu In conjunction with PACNOG 4 Router device security lab 1. APNIC s remote lab In these exercises you will be remotely accessing
More informationNetwork Diagram and Configuration Files
CHAPTER 7 This chapter contains a topology diagram and the associated router, firewall, and switch configuration files for the devices in this sample implementation. See Figure 1. Figure 1 Network Diagram
More informationLab 6.1 Configuring a Cisco IOS Firewall Using SDM
Lab 6.1 Configuring a Cisco IOS Firewall Using SDM Learning Objectives Use SDM to configure a router as a firewall Understand basic firewall operation Configure basic routing through a firewall Verify
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationLab 6.1.3 Configure Local AAA on Cisco Router
Lab 6.1.3 Configure Local AAA on Cisco Router Objective Scenario Topology In this lab, the students will complete the following tasks: Securing and testing access to the privileged EXEC, VTY, and console
More informationUsing Two-Factor Authentication Configuration to Combat Cybersecurity Threats
Using Two-Factor Authentication Configuration to Combat Cybersecurity Threats Guidelines for Deploying Cisco IOS SSH with X.509v3 PIV and CAC Smartcards Contents page Introduction 3 Requirements 3 Resolved
More informationBasic Router Configuration Using Cisco Configuration Professional
Basic Router Configuration Using Cisco Configuration Professional Document ID: 111999 Contents Introduction Prerequisites Components Used Install Cisco Configuration Professional Router Configuration to
More informationBRI to PRI Connection Using Data Over Voice
BRI to PRI Connection Using Data Over Voice Document ID: 14962 Contents Introduction Prerequisites Requirements Conventions Background Information Configure Network Diagram Configurations Verify Troubleshoot
More informationTask 20.1: Configure ASBR1 Serial 0/2 to prevent DoS attacks to ASBR1 from SP1.
Task 20.1: Configure ASBR1 Serial 0/2 to prevent DoS attacks to ASBR1 from SP1. Task 20.2: Configure an access-list to block all networks addresses that is commonly used to hack SP networks. Task 20.3:
More informationLet's take a look at another example, which is based on the following diagram:
Chapter 3 - Voice Dial Peers In order to understand the concept of dial peers, it is important to understand call legs. A voice call over a packet network is segmented into discrete call legs. A call leg
More informationCCNA Security. Chapter Two Securing Network Devices. 2009 Cisco Learning Institute.
CCNA Security Chapter Two Securing Network Devices 1 The Edge Router What is the edge router? - The last router between the internal network and an untrusted network such as the Internet - Functions as
More informationAT&T IP Flex Reach/ IP Toll Free Configuration Guide IC 3.0 with Interaction SIP Proxy
INTERACTIVE INTELLIGENCE AT&T IP Flex Reach/ IP Toll Free Configuration Guide IC 3.0 with Interaction SIP Proxy Version 1.7 9/2/2009 TABLE OF CONTENTS 1 AT&T... 5 1.1 Introduction... 5 1.2 Product Descriptions...
More informationDial Peer Configuration Examples
Dial Peer Configuration Examples This appendix contains a series of configuration examples featuring the minimum required components and critical Cisco IOS command lines extracted from voice gateway configuration
More informationCisco Voice Gateways. PacNOG6 VoIP Workshop Nadi, Fiji. November 2009. Jonny Martin - jonny@jonnynet.net
Cisco Voice Gateways PacNOG6 VoIP Workshop Nadi, Fiji. November 2009 Jonny Martin - jonny@jonnynet.net Voice Gateways Any device with one or more TDM PSTN interfaces on them TDM - Time Division Multiplexing
More informationNote: As of Feb 25, 2010 Priority Telecom has not completed FXS verification of fax capabilities. This will be updated as soon as verified.
1 SIP Carriers 1.1 Priority Telecom 1.1.1 Warnings Check the SIP 3 rd Party SIP Carrier Matrix for certification status, and supported features. More info about the SIP 3 rd Party SIP Carrier Matrix can
More informationDocument ID: 45741. Introduction
Products & Services 6bone Connection Using 6to4 Tunnels for IPv6 Document ID: 45741 Contents Introduction Prerequisites Requirements Components Used Conventions How 6to4 Tunnels Work Limitations of 6to4
More informationLab 8.3.1.2 Configure Basic AP Security through IOS CLI
Lab 8.3.1.2 Configure Basic AP Security through IOS CLI Estimated Time: 30 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, the student will learn the following
More informationTotalCloud Phone System
TotalCloud Phone System Cisco SF 302-08P PoE VLAN Configuration Guide Note: The below information and configuration is for deployment of the Cbeyond managed switch solution using the Cisco 302 8 port Power
More informationJuniper Networks WX Series Large. Integration on Cisco
APPLICATION NOTE Juniper Networks WX Series Large Deployment with WCCP Off-Path Integration on Cisco Integrating Multiple Juniper Networks WX Series Application Acceleration Platforms into a Cisco Infrastructure
More informationCall Flows for Simple IP Users
This chapter provides various call flows for simple IP users. Finding Feature Information, page 1 Simple IP Unclassified MAC Authentication (MAC TAL and Web Login) Call Flows, page 1 Finding Feature Information
More informationOutput Interpreter. SHOW RUNNING-CONFIG SECURITY Analysis SHOW RUNNING-CONFIG - FW Analysis. Back to top
Output Interpreter You have chosen to display errors warnings general information, and helpful references. Headings are displayed for all supported commands that you submitted. SHOW RUNNING-CONFIG SECURITY
More informationConfiguration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example Document ID: 113337 Contents Introduction Prerequisites Requirements Components Used Conventions Configuration
More information1 SIP Carriers. 1.1.1 Warnings. 1.1.2 Vendor Contact Vendor Web Site : http://www.wind.it. 1.1.3 Versions Verified SIP Carrier status as of 9/11/2011
1 SIP Carriers 1.1.1 Warnings Check the SIP 3 rd Party SIP Carrier Matrix for certification status, and supported features. More info about the SIP 3 rd Party SIP Carrier Matrix can be found in the SIP
More informationSkills Assessment Student Training Exam
Skills Assessment Student Training Exam Topology Assessment Objectives Part 1: Initialize Devices (8 points, 5 minutes) Part 2: Configure Device Basic Settings (28 points, 30 minutes) Part 3: Configure
More informationDesign & Implementation of SIP Trunking using Cisco s Session Border Controllers
Design & Implementation of SIP Trunking using Cisco s Session Border Controllers Graham Francis CEO, The SIP School Darryl Sladden Technical Marketing Manager, Cisco Pashmeen Mistry Technical Marketing
More informationHow to Configure the Cisco UC500 for use with Integra Telecom SIP Solutions
How to Configure the Cisco UC500 for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Cisco UC500 IP PBX to connect to Integra Telecom SIP Trunks.
More informationInstallation & Configuration Guide Version 1.0. TekSIP Route Server Version 1.0 - Installation & Configuration Guide
TekSIP Route Server Installation & Configuration Guide Version 1.0 2011 Yasin KAPLAN - http://www.teksip.com/ 1 Document Revision 1.1 http://www.teksip.com/ TekSIP Route Server is built by Yasin KAPLAN
More informationLAB II: Securing The Data Path and Routing Infrastructure
LAB II: Securing The Data Path and Routing Infrastructure 8. Create Packet Filters a. Create a packet filter which will deny packets that have obviously bogus IP source addresses but permit everything
More informationDeployment Guidelines for QoS Configuration in DSL Environment
White Paper Deployment Guidelines for QoS Configuration in DSL Environment Overview In the late 1980s, DSL technology was developed to provide higher-speed digital data transmission over local telephone
More informationUsing the NetVanta 7100 Series
MENU OK CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL 1 2
More informationSecurity Audit CHAPTER21. Perform Security Audit
CHAPTER21 Perform is a feature that examines your existing router configurations and then updates your router in order to make your router and network more secure. is based on the Cisco IOS AutoSecure
More informationPT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations
PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations Instructor Version Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1
More informationUsing LiveAction with Cisco Secure ACS (TACACS+ Server)
LiveAction Application Note Using LiveAction with Cisco Secure ACS (TACACS+ Server) September 2012 http://www.actionpacked.com Table of Contents 1. Introduction... 1 2. Cisco Router Configuration... 2
More informationConfigurazione Rete VoIP
Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul
More informationDS3 Performance Scaling on ISRs
This document provides guidelines on scaling the performance of DS3 interface (NM-1T3/E3) for the Cisco 2811/2821/2851/3825/3845 Integrated Services Routers. The analysis provides following test results;
More informationPlanning Maintenance for Complex Networks
Planning Maintenance for Complex Networks CCNP TSHOOT: Maintaining and Troubleshooting IP Networks Olga Torstensson TSHOOT v6 1 Maintenance Models and Methodologies A network engineer s job description
More informationCenter for Internet Security Gold Standard Benchmark for Cisco IOS
Center for Internet Security Gold Standard Benchmark for Cisco IOS Level 1 and 2 Benchmarks Version 2.1 http://www.cisecurity.org rat-feedback@cisecurity.org September 2, 2003 Abstract This document defines
More informationADTRAN SBC and Cisco Unified Call Manager SIP Trunk Interoperability
6AOSSG0004-42A April 2013 Interoperability Guide ADTRAN SBC and Cisco Unified Call Manager SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability
More informationSupported Platforms. Supported Standards, MIBs, and RFCs. Prerequisites. Related Features and Technologies. Related Documents. Improved Server Access
Configuring Timeout, Retransmission, and Key Values per RADIUS Server The Configuring Timeout, Retransmission, and Key Values per RADIUS Server feature extends the functionality of the existing radius-server
More informationConfigurazione Rete VoIP
Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul
More informationNetwork Security Knowledge is Everything! Network Operations
Network Security Knowledge is Everything Network Operations Warrick Mitchell - Network Engineer warrick.mitchell@aarnet.edu.au Agenda What is Network Security General Configuration Security Logging and
More informationCisco Virtual Office Deployment Guide
Cisco Virtual Office Deployment Guide Scope of Document This deployment guide provides detailed information on configuring the Cisco Virtual Office headend devices and ManageExpress Virtual Office. It
More informationConfiguring a Leased Line
CHAPTER 4 Configuring a Leased Line The configuration in this chapter describes how to configure a Cisco 1700 router for IP and IPX over a synchronous serial line. Before You Begin The configuration in
More information