Brest. Backup : copy flash:ppe_brest1 running-config
|
|
|
- Nathan Watts
- 10 years ago
- Views:
Transcription
1 Brest Backup : copy flash:ppe_brest1 running-config Cisco SF Mise en place des services : - Serveurs : /24 VLAN 2 (port 1) - DSI : /24 VLAN 3 (port 2) - Direction : /24 VLAN 4 (port 3) - Finances : /24 VLAN 5 (port 4) - Marketing : /24 VLAN 6 (port 5) - RH : /24 VLAN 7 (port 6) - Accueil : /24 VLAN 8 (port 7) Le port 8 est configuré pour dialoguer vers tous les ports VLAN par défaut 1 vers le routeur central «BREST» Il faut spécifier les différentes routes sur le Cisco SF :
2 Mise en place du routage entre les différents services afin de limiter les domaines de diffusion. Comment nos VLAN ont été mis en place : VLAN 2 : VLAN 3 : VLAN 4 : VLAN 5 : VLAN 6 : VLAN 7 : VLAN 8 : Pour fini le VLAN par défaut 1 :
3 Puis, pour finir la configuration des routes : Configuration du routeur Cisco 1941 brest : brest#show run Building configuration... Current configuration : 2126 bytes Last configuration change at 15:39:05 UTC Thu Dec version 15.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname brest boot-start-marker boot-end-marker no aaa new-model no ipv6 cef ip source-route ip cef multilink bundle-name authenticated crypto pki token default removal timeout 0 license udi pid CISCO1941/K9 sn FCZ1648C1SF
4 interface Embedded-Service-Engine0/0 shutdown interface GigabitEthernet0/0 ip address ip nat inside ip virtual-reassembly in duplex auto speed auto interface GigabitEthernet0/1 ip address ip nat inside ip virtual-reassembly in duplex auto speed auto interface Serial0/0/0 shutdown clock rate interface Serial0/0/1 shutdown clock rate interface GigabitEthernet0/1/0 interface GigabitEthernet0/1/1 interface GigabitEthernet0/1/2 interface GigabitEthernet0/1/3 switchport access vlan 2 interface Vlan1 interface Vlan2 ip address ip nat outside ip nat enable ip virtual-reassembly in ip forward-protocol nd no ip http server no ip http secure-server ip nat inside source list 1 interface Vlan2 overload ip nat inside source static tcp extendable ip route ip route ip route ip route ip route ip route ip route ip route access-list 1 permit any control-plane line con 0 line aux 0
5 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 login transport input all scheduler allocate end Puis, la configuration du Switch CISCO SF interface ethernet e1 switchport mode general vlan database vlan 2-8 interface ethernet e1 switchport general pvid 2 interface ethernet e1 switchport general allowed vlan add 2 untagged switchport trunk allowed vlan add 2 interface ethernet e2 switchport trunk native vlan 3 switchport trunk allowed vlan add 3 interface ethernet e3 switchport trunk native vlan 4 switchport trunk allowed vlan add 4 interface ethernet e4 switchport trunk native vlan 5 switchport trunk allowed vlan add 5 interface ethernet e5 switchport trunk native vlan 6 switchport trunk allowed vlan add 6 interface ethernet e6 switchport trunk native vlan 7 switchport trunk allowed vlan add 7 interface ethernet e7 switchport trunk native vlan 8 switchport trunk allowed vlan add 8 interface vlan 2 name Serveurs interface vlan 3 name DSI interface vlan 4 name Direction interface vlan 5 name Finances
6 interface vlan 6 name Marketing interface vlan 7 name RH interface vlan 8 name Accueil voice vlan oui-table add 0001e3 Siemens_AG_phone voice vlan oui-table add 00036b Cisco_phone voice vlan oui-table add 00096e Avaya voice vlan oui-table add 000fe2 H3C_Aolynk voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone voice vlan oui-table add 00d01e Pingtel_phone voice vlan oui-table add 00e075 Polycom/Veritel_phone voice vlan oui-table add 00e0bb 3Com_phone interface vlan 1 ip address interface vlan 2 ip address interface vlan 3 ip address interface vlan 4 ip address interface vlan 5 ip address interface vlan 6 ip address interface vlan 7 ip address interface vlan 8 ip address ip route ip route interface vlan 1 dhcp bonjour mode include bonjour service enable csco-sb bonjour service enable http bonjour service enable https bonjour service enable ssh bonjour service enable telnet bonjour interface range vlan-range 1 hostname switchcce2e7 username cisco password 95fbdb3e3d93f62058f8c18acd1d01130b16296c level 15 encrypted no snmp-server enable Après test, on peut accéder depuis le réseau /20 au serveur de la DMZ de brest :
CS3695/M6-109 Lab 8-NPS02 VOIP Sniffing Ver. 8 Rev. 0
Background For this lab, we will be analyzing some Wireshark capture files that were captured using the ARP Poisoning technique on Cisco VIOP (Voice Over IP) phones As this lab took special equipment (i.e.
Lab Configuring Syslog and NTP (Instructor Version)
(Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
Simple MPLS network topology for Dynamips/Olive
Simple MPLS network topology for Dynamips/Olive R1 version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname R1 boot-start-marker
Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router
Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue este capítulo Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue el libro completo
TotalCloud Phone System
TotalCloud Phone System Cisco SF 302-08P PoE VLAN Configuration Guide Note: The below information and configuration is for deployment of the Cbeyond managed switch solution using the Cisco 302 8 port Power
Skills Assessment Student Training (Answer Key)
CCNA: Connecting Networks Skills Assessment Student Training (Answer Key) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Assessment
CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA. Switch S1 S1#sh ru Building configuration...
CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA Switch S1 S1#sh ru Building configuration... Current configuration : 1639 bytes version 12.2 no service timestamps log datetime
and 2, implemented With Cisco Unified Border Control Element (CUBE)
www.xo.com XO SIP Service Customer Configuration Guide for Cisco Unified Communications Manager (CUCM) 8.0.3 XO SIP Packages 1 and 2, implemented With Cisco Unified Border Control Element (CUBE) 1 PRODUCT
How To Configure A Cisco Router With A Cio Router
CHAPTER 1 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering
Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering 7.1 Details Aim: Rich Macfarlane The aim of this lab is to introduce the concepts of stateful firewalls, using Cisco Contextbased Access Control
Configuring Voice and Data Support on VWIC3s
First Published: July 21, 2010, OL-22847-01 This module describes how to configure voice and data support on the next generation of voice/wan Interface Cards (VWICs) also known as VWIC3s. The following
Table of Contents. Cisco Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others
Cisco IOS Firewall to Allow Java Applets From Known Sites w Table of Contents Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others...1 Introduction...1 To Deny Java
Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration
Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration Summary This setup covers the of the TEAM VoWLAN solution with a Cisco Communications Manager Express 4.1 +. This integration
ICND1-100-101 IOS CLI Study Guide (CCENT)
ICND1-100-101 IOS CLI Study Guide (CCENT) Hostname: 2. hostname SW1 SWITCH CONFIGURATION Mgmt IP: 2. interface vlan 1 3. ip address 10.0.0.2 4. no shut Gateway: 2. ip default-gateway 10.0.0.1 Local User/Pwd:
Felix Rohrer. PT Activity 7.5.3: Troubleshooting Wireless WRT300N. Topology Diagram
Felix Rohrer PT Activity 7.5.3: Troubleshooting Wireless WRT300N Topology Diagram All contents are Copyright 1992 2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
The Cisco IOS Firewall feature set is supported on the following platforms: Cisco 2600 series Cisco 3600 series
Cisco IOS Firewall Feature Set Feature Summary The Cisco IOS Firewall feature set is available in Cisco IOS Release 12.0. This document includes information that is new in Cisco IOS Release 12.0(1)T, including
Lab 6.1.3 Configure Local AAA on Cisco Router
Lab 6.1.3 Configure Local AAA on Cisco Router Objective Scenario Topology In this lab, the students will complete the following tasks: Securing and testing access to the privileged EXEC, VTY, and console
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example Document ID: 113337 Contents Introduction Prerequisites Requirements Components Used Conventions Configuration
Lab 5.3.9b Managing Router Configuration Files Using TFTP
Lab 5.3.9b Managing Router Configuration Files Using TFTP Device Host Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Download and install TFTP server software.
SIP Trunking Configuration Guide for Cisco Unified Communications Manager (CUCM) Version 9.0.1.11005-1 with Cisco Unified Border Element (CUBE)
SIP Trunking Configuration Guide for Cisco Unified Communications Manager (CUCM) Version 9.0.1.11005-1 with Cisco Unified Border Element (CUBE) Table of Contents Introduction... 3 Executive Summary..3
Juniper Networks WX Series Large. Integration on Cisco
APPLICATION NOTE Juniper Networks WX Series Large Deployment with WCCP Off-Path Integration on Cisco Integrating Multiple Juniper Networks WX Series Application Acceleration Platforms into a Cisco Infrastructure
Configurazione Rete VoIP
Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul
Case Study 1: Registering IP Phones with a remote Call
Case Study 1: Registering IP Phones with a remote Call Manager Objectives Place calls from IP Phones under R1 to IP Phones under R2 Place calls from any IP Phone (under R1 and under R2) to the regular
TP : Configuration de routeurs CISCO
TP : Configuration de routeurs CISCO Sovanna Tan Novembre 2010 révision décembre 2012 1/19 Sovanna Tan TP : Routeurs CISCO Plan 1 Présentation du routeur Cisco 1841 2 Le système d exploitation /19 Sovanna
Configurazione Rete VoIP
Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul
Configuring the Cisco Secure PIX Firewall with a Single Intern
Configuring the Cisco Secure PIX Firewall with a Single Intern Table of Contents Configuring the Cisco Secure PIX Firewall with a Single Internal Network...1 Interactive: This document offers customized
Configuring the MNLB Forwarding Agent
CHAPTER 3 Configuring the MNLB Forwarding Agent This chapter describes how to configure a Cisco router as an MNLB Forwarding Agent to operate in conjunction with a Cisco LocalDirector serving as Services
IDT / Net2phone SIP Trunking Configuration Guide for Cisco Business Edition 3000 (BE3000) Release 8.6.4 with Cisco Unified Border Element Release 8.8.
Application Notes IDT / Net2phone SIP Trunking Configuration Guide for Cisco Business Edition 3000 (BE3000) Release 8.6.4 with Cisco Unified Border Element Release 8.8. May 31, 2013 Eric Cimino IDT Corporation
ICND1 Lab Guide. 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0. Labs powered by
ICND1 Lab Guide 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0 ii Interconnecting Cisco Networking Devices Part 1 100-101 Lab Guide LM20130929/BV2.01 iii 25 Century Blvd. Ste. 500
IPSec. User Guide. 2120028 Rev 2.2
IPSec User Guide 2120028 Rev 2.2 Important Notice Safety and Hazards Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted
Lab 8.3.1.2 Configure Basic AP Security through IOS CLI
Lab 8.3.1.2 Configure Basic AP Security through IOS CLI Estimated Time: 30 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, the student will learn the following
APNIC Members Training Course Security workshop. 2-4 July, 2008. Port Vila Vanuatu. In conjunction with PACNOG 4
APNIC Members Training Course Security workshop 2-4 July, 2008 Port Vila Vanuatu In conjunction with PACNOG 4 Router device security lab 1. APNIC s remote lab In these exercises you will be remotely accessing
Lab 3.5.1: Basic VLAN Configuration (Instructor Version)
(Instructor Version) Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0
Configuring a Cisco 2509-RJ Terminal Router
created by: Rainer Bemsel Version 1.0 Dated: Dec/08/2012 For my Cisco LAB, I ve purchased a used Cisco 2509-RJ with RJ45-RJ45 roll-over cables. This TechTip shows my configuration setup, so you can easily
Skills Assessment Student Training Exam
Skills Assessment Student Training Exam Topology Assessment Objectives Part 1: Initialize Devices (8 points, 5 minutes) Part 2: Configure Device Basic Settings (28 points, 30 minutes) Part 3: Configure
P and FTP Proxy caching Using a Cisco Cache Engine 550 an
P and FTP Proxy caching Using a Cisco Cache Engine 550 an Table of Contents HTTP and FTP Proxy caching Using a Cisco Cache Engine 550 and a PIX Firewall...1 Introduction...1 Before You Begin...1 Conventions...1
BRI to PRI Connection Using Data Over Voice
BRI to PRI Connection Using Data Over Voice Document ID: 14962 Contents Introduction Prerequisites Requirements Conventions Background Information Configure Network Diagram Configurations Verify Troubleshoot
How To Configure A Cisco Vpn On A Cell Phone With A Pkv On A Safd On A Pv On An Asda On A Network With A Network On A Pc Or Ipv On The Ipv (Svv
CHAPTER 17 The Cisco VPN Client for Cisco Unified IP Phones adds another option for customers attempting to solve the remote telecommuter problem by complementing other Cisco remote telecommuting offerings.
PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations
PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations Instructor Version Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1
Virtual Private Network Setup
This chapter provides information about virtual private network setup. Virtual Private Network, page 1 Devices Supporting VPN, page 2 Set Up VPN Feature, page 2 Complete Cisco IOS Prerequisites, page 3
Configuring Clocking and Timing
CHAPTER 16 Clock synchronization is important for a variety of applications, including synchronization of radio cell towers. While legacy TDM protocols incorporate timing features, packet-switched networks
Table of Contents. Cisco Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access
Table of Contents Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...1 Configure...2
Configuring Fax Pass-Through
Configuring Fax Pass-Through This chapter describes the configuration of fax pass-through. With fax pass-through, modulated fax information from the PSTN is passed in-band over a voice speech path in an
login timeout 30 access list ALL line 20 extended permit ip any any port 9053 interval 15 passdetect interval 30
logging enable logging console 4 logging timestamp logging trap 5 logging buffered 4 logging device id hostname logging host 10.0.128.240 udp/514 format emblem logging host 10.0.143.24 udp/514 login timeout
Proposal for implementation of VoIP at XYZ hospital.
Proposal for implementation of VoIP at XYZ hospital. Introduction Management committee of XYZ hospital wants to implement an internal voice communication system for their hospital. At present they are
Virtual Fragmentation Reassembly
Virtual Fragmentation Reassembly Currently, the Cisco IOS Firewall specifically context-based access control (CBAC) and the intrusion detection system (IDS) cannot identify the contents of the IP fragments
Apache CloudStack 4.x (incubating) Network Setup: excerpt from Installation Guide. Revised February 28, 2013 2:32 pm Pacific
Apache CloudStack 4.x (incubating) Network Setup: excerpt from Installation Guide Revised February 28, 2013 2:32 pm Pacific Apache CloudStack 4.x (incubating) Network Setup: excerpt from Installation Guide
Lab 11.5.6.1 Configure Syslog on AP
Lab 11.5.6.1 Configure Syslog on AP Estimated Time: 25 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, students will configure and use syslog logging to monitor
Cisco Routers and Switches
Cisco Routers and Switches Phoenix Cisco User Group (PCUG) Tools, tips, and tricks you never knew Hello! Jeremy D. Cioara - CCIE, MCSE, CNE AdTEC Networks - Chief Information Officer Cisco IP Telephony
LAN-Cell to Cisco Tunneling
LAN-Cell to Cisco Tunneling Page 1 of 13 LAN-Cell to Cisco Tunneling This Tech Note guides you through setting up a VPN connection between a LAN-Cell and a Cisco router. As the figure below shows, the
CCT vs. CCENT Skill Set Comparison
Operation of IP Data Networks Recognize the purpose and functions of various network devices such as Routers, Switches, Bridges and Hubs Select the components required to meet a given network specification
- The PIX OS Command-Line Interface -
1 PIX OS Versions - The PIX OS Command-Line Interface - The operating system for Cisco PIX/ASA firewalls is known as the PIX OS. Because the PIX product line was acquired and not originally developed by
Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500
Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500 Objective Use Cisco Discovery Protocol (CDP) commands to get information about neighboring network devices. Background/Preparation CDP
Remote Access VPN Business Scenarios
CHAPTER 4 This chapter explains the basic tasks for configuring an IP-based, remote access Virtual Private Network (VPN) on a Cisco 7200 series router. In the remote access VPN business scenario, a remote
Cisco ASA Configuration Guidance
Cisco ASA Configuration Guidance Abstract The modern network perimeter is more complicated than ever. The number of applications, protocols, and attacks that a firewall is expected to support and protect
Basic Router Configuration
CHAPTER 3 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
Using LiveAction with Cisco Secure ACS (TACACS+ Server)
LiveAction Application Note Using LiveAction with Cisco Secure ACS (TACACS+ Server) September 2012 http://www.actionpacked.com Table of Contents 1. Introduction... 1 2. Cisco Router Configuration... 2
Using a Sierra Wireless AirLink Raven X or Raven-E with a Cisco Router Application Note
Using a Sierra Wireless AirLink Raven X or Raven-E with a Application Note Cisco routers deliver the performance, availability, and reliability required for scaling mission-critical business applications
One-Step Lockdown with Cisco SDM
One-Step Lockdown with Cisco SDM Router Hardening Automagically The process of turning off unnecessary services is called hardening a router to prevent attacks or exploits. The basic steps of router hardening
Securing the Connected Enterprise
Securing the Connected Enterprise ABID ALI, Network and Security Consultant. Why Infrastructure Matters Rapidly Growing Markets Global Network Infrastructure and Security Markets 13.7% CAGR over the next
Enabling Management Protocols: NTP, SNMP, and Syslog
SECTION 7 Enabling Management Protocols: NTP, SNMP, and Syslog In this Section This section describes how to enable basic management protocols on a Cisco AS5800 and Cisco AS5300 as part of a dial access
Network Security Knowledge is Everything! Network Operations
Network Security Knowledge is Everything Network Operations Warrick Mitchell - Network Engineer [email protected] Agenda What is Network Security General Configuration Security Logging and
Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials.
Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials. CHAPTER 5 OBJECTIVES Configure a router with an initial configuration. Use the
Configuring Modem Transport Support for VoIP
Configuring Modem Transport Support for VoIP This chapter explains how to configure modem transport support for Voice over IP (VoIP) and contains the following sections: Modem Transport Support Overview,
Configuring Static and Dynamic NAT Simultaneously
Configuring Static and Dynamic NAT Simultaneously Document ID: 13778 Contents Introduction Prerequisites Requirements Components Used Conventions Configuring NAT Related Information Introduction In some
Configuring PEAP / LDAP based authentication using FreeRADIUS on Debian Sarge and Cisco AP1200, with WPA2 AES encryption
Configuring PEAP / LDAP based authentication using FreeRADIUS on Debian Sarge and Cisco AP1200, with WPA2 AES encryption Ivan Klimek Computer Networks Laboratory Technical University Kosice, Slovakia http://www.cnl.tuke.sk
TotalCloud Phone System
TotalCloud Phone System Adtran Netvanta 1234P PoE VLAN Configuration Guide Note: The below information and configuration is for deployment of the Cbeyond managed switch solution using the Adtran Netvanta
Deployment Guidelines for QoS Configuration in DSL Environment
White Paper Deployment Guidelines for QoS Configuration in DSL Environment Overview In the late 1980s, DSL technology was developed to provide higher-speed digital data transmission over local telephone
Basic Router Configuration Using Cisco Configuration Professional
Basic Router Configuration Using Cisco Configuration Professional Document ID: 111999 Contents Introduction Prerequisites Components Used Install Cisco Configuration Professional Router Configuration to
Configuring Role-Based Access Control
5 CHAPTER This chapter describes how to configure role-based access control (RBAC) on the Cisco Application Control Engine (ACE) module. This chapter contains the following sections: Information About
Installation of the On Site Server (OSS)
Installation of the On Site Server (OSS) rev 1.1 Step #1 - Initial Connection to the OSS Having plugged in power and an ethernet cable in the eth0 interface (see diagram below) you can connect to the unit
HOW TO CONFIGURE CISCO FIREWALL PART I
HOW TO CONFIGURE CISCO FIREWALL PART I Cisco Abstract: Please find below a step by step process to configure the PIX Firewall from scratch. A simple scenario is given here where you have a corporate network
Configuring InterVLAN Routing and ISL/802.1Q Trunking on Catalyst 2900XL/3500XL/2940/2950/2970 Series Switches Using an External Router
Configuring InterVLAN Routing and ISL/802.1Q Trunking on Catalyst 2900XL/3500XL/2940/2950/2970 Series Switches Using an External Router Document ID: 14976 Introduction Before You Begin Conventions Prerequisites
Network Simulator Lab Study Plan
The CCNA 640-802 Network Simulator has 300 lab exercises, organized both by type (Skill Builder, Configuration Scenario, Troubleshooting Scenario, and Subnetting Exercise) and by major topic within each
Switch Configuration Required to Support Cisco ISE Functions
APPENDIXC Switch Configuration Required to Support Cisco ISE Functions To ensure Cisco ISE is able to interoperate with network switches and functions from Cisco ISE are successful across the network segment,
Document ID: 45741. Introduction
Products & Services 6bone Connection Using 6to4 Tunnels for IPv6 Document ID: 45741 Contents Introduction Prerequisites Requirements Components Used Conventions How 6to4 Tunnels Work Limitations of 6to4
WiNG 5.X How To. Policy Based Routing Cache Redirection. Part No. TME-05-2012-01 Rev. A
WiNG 5.X How To Policy Based Routing Cache Redirection Part No. TME-05-2012-01 Rev. A MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark
Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example
Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example Document ID: 45843 Introduction Prerequisites Requirements Components Used Conventions Background Information Configure Passwords
Lab 8: Confi guring QoS
Lab 8: Objective Implement QoS, mark traffi c, and display and interpret QoS output. Lab Topology For this lab, your network design will include two pods of devices. You will be responsible for confi guring
Using Link Layer Discovery Protocol in Multivendor Networks
Using Link Layer Discovery Protocol in Multivendor Networks Link Layer Discovery Protocol (LLDP), standardized by the IEEE as part of 802.1ab, enables standardized discovery of nodes, which in turn facilitates
Network Security 2. Module 6 Configure Remote Access VPN
1 1 Network Security 2 Module 6 Configure Remote Access VPN 2 Learning Objectives 6.1 Introduction to Cisco Easy VPN 6.2 Configure the Easy VPN Server 6.3 Configure Easy VPN Remote for the Cisco VPN Client
Network Security and AAA
ICT Technical Update Module Network Security and AAA Prof. Dr Harsha Sirisena Electrical and Computer Engineering University of Canterbury AAA Introduction Overview A network administrator may allow remote
System Components PBX Model. Configuration Tasks
Cisco 3600 Series Gateway-PBX Interoperability: Lucent Definity G3 with T1 PRI Signaling This document describes the interoperability and configuration of a Cisco 3600 series voice gateway with a Lucent
Troubleshooting the Firewall Services Module
CHAPTER 25 This chapter describes how to troubleshoot the FWSM, and includes the following sections: Testing Your Configuration, page 25-1 Reloading the FWSM, page 25-6 Performing Password Recovery, page
Network Diagram Scalability Testbed and Configuration Files
APPENDIX A Network Diagram Scalability Testbed and Configuration Files This appendix contains configurations that were used during a V 3 PN performance and scalability evaluation based on the network illustrated
Configuring WAN Failover with a Cisco 881 Router and an AirLink ES440
Configuring WAN Failover with a Cisco 881 Router and an AirLink ES440 When the AirLink ES440 is combined with a third-party router, the combined solution supports business continuity by providing primary
Flow-Based per Port-Channel Load Balancing
The feature allows different flows of traffic over a Gigabit EtherChannel (GEC) interface to be identified based on the packet header and then mapped to the different member links of the port channel.
Configuring EtherChannel and 802.1Q Trunking Between Catalyst L2 Fixed Configuration Switches and Catalyst Switches Running CatOS
Configuring EtherChannel and 802.1Q Trunking Between Catalyst L2 Fixed Configuration Switches and Catalyst Switches Running CatOS Document ID: 23408 Contents Introduction Prerequisites Requirements Components
ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability
6AOSSG0007-42A March 2013 Interoperability Guide ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability
Configuring Switch Ports and VLAN Interfaces for the Cisco ASA 5505 Adaptive Security Appliance
CHAPTER 4 Configuring Switch Ports and VLAN Interfaces for the Cisco ASA 5505 Adaptive Security Appliance This chapter describes how to configure the switch ports and VLAN interfaces of the ASA 5505 adaptive
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.
Application Note Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.323 Gateway Introduction This document describes the interoperability
!! Last configuration change at 15:00:48 gmt Thu Oct 11 2012 by admin! NVRAM config last updated at 03:07:42 gmt Wed Nov 14 2012 by admin!
Last configuration change at 15:00:48 gmt Thu Oct 11 2012 by admin NVRAM config last updated at 03:07:42 gmt Wed Nov 14 2012 by admin version 12.2 no service pad service timestamps debug datetime msec
WiNG 5.X How-To Guide
WiNG 5.X How-To Guide Captive Portals Part No. TME-12-2012-01 Rev. A MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC
Configuring System Message Logging
CHAPTER 25 This chapter describes how to configure system message logging on the Catalyst 2960 switch. Note For complete syntax and usage information for the commands used in this chapter, see the Cisco
Configuring a Leased Line
CHAPTER 4 Configuring a Leased Line The configuration in this chapter describes how to configure a Cisco 1700 router for IP and IPX over a synchronous serial line. Before You Begin The configuration in
Cisco Certified Network Associate Exam. Operation of IP Data Networks. LAN Switching Technologies. IP addressing (IPv4 / IPv6)
Cisco Certified Network Associate Exam Exam Number 200-120 CCNA Associated Certifications CCNA Routing and Switching Operation of IP Data Networks Operation of IP Data Networks Recognize the purpose and
Welcome to Todd Lammle s CCNA Bootcamp
Welcome to Todd Lammle s CCNA Bootcamp Todd Lammle Cisco Authorized CCNA Bootcamps are now available, delivered by CCSI instructor, and popular Sybex author Todd Lammle. Todd Lammle CCNA Training Boot
EIGRP Routing Protocol & Configuration
EIGRP Routing Protocol & Configuration ~ GNU Public License ~ ma2d http: // www.oscentre.co.nr A) EIGRP Definition There is several terms on routing protocol, as we know RIP, IGRP/EIGRP, OSPF, BGP is major
642 523 Securing Networks with PIX and ASA
642 523 Securing Networks with PIX and ASA Course Number: 642 523 Length: 1 Day(s) Course Overview This course is part of the training for the Cisco Certified Security Professional and the Cisco Firewall