Cisco Unified Communications Manager with Cisco Unified Border Element (IOS 15.4(2)T) using SIP

Transcription

1 Application Note COX SIP Trunking: Cisco Unified Communications Manager with Cisco Unified Border Element (IOS 15.4(2)T) using SIP May 06, 2014 Page 1 of 58

2 Table of Contents Introduction... 3 Network Topology... 4 System Components... 5 Hardware Components... 5 Software Requirements... 5 Features Supported... 5 Features Not Supported... 5 Caveats... 6 Configuration... 7 Configuring the Cisco Unified Border Element... 7 Network interface... 7 Global CUBE settings... 7 Media Passing through CUBE (media flow-through vs. media flow-around)... 8 Codecs... 8 Voice translation rule... 8 Dial peer... 9 Call flow Configuring the Cisco Unified Communications Manager Cisco CallManager service parameter Device Pool, Region and Audio Codec Preference List Offnet calls via Cox SIP Trunk Dialplan Acronyms Important Information Appendix A: Test Results Table of Figures Figure 1 Network Topology... 4 Figure 2: Outbound Voice Call Figure 3: Outboud Fax Call Figure 4Service Parameter Figure 5 Service Parameter Cont Figure 6 Service Parameter Cont Figure 7 Service Parameter Cont Figure 8 Service Paramater Cont Figure 9 Service Parameter Cont Figure 10 Service Parameter Cont Figure 11 Service Parameter Cont Figure 12 Service Parameter Cont Figure 13 Service Parameter Cont Figure 14 Service Parameter Cont Figure 15 Service parameter Cont Figure 16 Service Parameter Cont Figure 17 Device Pool Figure 18 Audio Codec Preference List Figure 19 Region Figure 20 SIP Trunk Security Profile Figure 21 SIP Profile Figure 22 SIP Profile Cont Figure 23 SIP Trunks List Figure 24 SIP Trunk to CUBE Figure 25 SIP Trunk to CUBE Cont Figure 26 SIP Trunk to CUBE Cont Figure 27 Translation Pattern Figure 28 Route Pattern Figure 29 Route Pattern for Voice Figure 30 Route Pattern for Fax Page 2 of 58

3 Introduction Service Providers today, such as Cox, are offering alternative methods to connect to the PSTN via their IP network. Most of these services utilize SIP as the primary signaling method and centralized IP to TDM POP gateways to provide on-net and off-net services. Cox is a service provider offering that allows connection to the PSTN and may offer the end customer a viable alternative to traditional PSTN connectivity. A demarcation device between these services and customer owned services is recommended. As an intermediary device between Cisco Unified Communications Manager and Cox Session Border Controller(EdgeMarc), Cisco Unified Border Element (CUBE) can be used. The Cisco Unified Border Element provides demarcation, security, interworking and session control services for Cisco Unified Communications Manager connected to Cox IP network. This document assumes the reader is knowledgeable with the terminology and configuration of CUCM (Cisco Unified Communications Manager). Only configuration settings specifically required for Cox interoperability are presented. Feature configuration and most importantly the dial plan are customer specific and need individual approach. This application note describes how to configure a Cisco Unified Communications Manager (Cisco UCM) and Cisco Unified Border Element (CUBE) for connectivity to Cox SIP trunking service. The deployment model covered in this application note is CPE (Cisco UCM 9.1.2) to PSTN (Cox). Testing was performed in accordance to Cox generic SIP trunking test methodology and among features verified were basic calls, DTMF transport, Music on Hold, Semi-attendant and attendant transfers, call forward, conferences, hunt groups, call pickup, call park, and interoperability with Cisco Unity Connection The CUCM configuration detailed in this document is based on a lab environment with a simple dial-plan used to ensure proper interoperability between Cox SIP network and Cisco Unified Communications. The configuration described in this document details the important configuration settings to have enabled for interoperability to be successful and care must be taken by the network administrator deploying Cisco UCM to interoperate to Cox SIP trunking network. This application note does not cover the use of calling search spaces (CSS) or partitions on Cisco Unified Communications Manager. To understand and learn how to apply CSS and partitions refer to the cisco.com link below: Page 3 of 58

4 Network Topology Basic Call Setup SIP Call Server /16 Customer Premise Cox VG224 IP: DID: SIP CUBE WAN IP: SIP CUBE(15.4) LAN IP: /24 SIP SIP Cox E-SBC LAN IP: /16 WAN IP: /26 SIP CUCM IP: SIP Session Border Controller (SBC) Cox Network PSTN SIP SCCP IP: DID: Fax IP: DID: IP: DID: Unity Connection IP: Figure 1 Network Topology Page 4 of 58

5 System Components Hardware Components Cisco UCM and Unity Connection run on VMware ISR G router IP phones 9971(SIP), 8961(SIP) and 7975(SCCP)( please consult Features not supported for restrictions) Cisco Voice Gateways 224 Software Requirements Cisco Unified Communications Manager IOS 15.4(2)T for Cisco Unified Border Element IOS 12.4(22)T5 for VG224 Voice Gateways Cisco Unity Connection Features Supported Incoming and outgoing offnet calls using G711Ulaw (Cox only offer G711Ulaw) with 20ms packetization Call hold Call transfer (Semi-attendant and Attendant) Call conference Call forward (all, busy, no answer) Call park Hunt groups Calling line (number) identification presentation (CLIP) Calling line (number) identification restriction (CLIR) DTMF (RFC2833) Unified Mobility (Single Number Reach feature) Media flow-through on CUBE Features Not Supported Outbound SIP REFER with Replaces. Cisco UCM does not currently support generation of an outbound SIP REFER with Replaces message, Cisco IP phones used in this test do not support Blind transfer, only Semi-attendant and Attendant transfer were tested Page 5 of 58

6 Caveats VG224 software version does not support T.38 SG3 fax, hence SG3 fax test call is not executed Cox Lab test network is closed network, some international test cases and early-media test are not executed Page 6 of 58

7 Configuration Configuring the Cisco Unified Border Element Network interface Configure Ethernet IP address and sub interface. The IP address and VLAN encapsulation used are for illustration only, the actual IP address can vary. For SIP trunks two IP addresses must be configured LAN and WAN. interface GigabitEthernet0/0 description COX Cisco CUCM9.1.2 test CUBE ip address duplex auto speed auto interface GigabitEthernet0/1 ip address duplex auto speed auto Global CUBE settings In order to enable CUBE IP2IP gateway functionality, following command has to be entered: voice service voip ip address trusted list ipv ipv address-hiding mode border-element allow-connections sip to sip no supplementary-service sip refer fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw sip asserted-id pai privacy pstn Page 7 of 58

8 early-offer forced midcall-signaling passthru sip-profiles 1 Explanation Command allow-connections sip to sip fax protocol asserted-id early-offer forced midcall-signaling passthru sip-profiles 1 Description Allow IP2IP connections between two SIP call legs Specifies the fax protocol Specifies the type of privacy header in the outgoing SIP requests and response messages Enables SIP Delayed-Offer to Early-Offer globally Passes SIP messages from one IP leg to another IP leg Apply sip profile at global level Media Passing through CUBE (media flow-through vs. media flow-around) Default CUBE configuration enables CUBE to work in flow-through mode(this test use Flow-through mode). In order to enable flow-around mode, please perform the following actions: voice service voip media flow-around Codecs Cox offer only G.711ulaw codec for voice call, it allows codecs other than G.711ulaw but will only accept G.711ulaw. For customers using G.711 alaw codec: voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw Voice translation rule We can configure voice translation rules to modify the number we want to send. You can create the rule using command voice translation-rule, apply the rule to the voice translation-profile. Then assign it to associated dial peer. voice translation-rule 1 Rule 1 /^8\(.*\)/ /\1/ Page 8 of 58

9 voice translation-profile DIGITSTRIP8 translate called 1 dial-peer voice 100 voip description outgoing fax to COX translation-profile outgoing DIGITSTRIP8 destination-pattern session protocol sipv2 session target sip-server codec g711ulaw ip qos dscp af32 signaling Command rule x translate called translation-profile outgoing Description Detail Match and Replace Rule x Define the translation profile rule for the called number. Define a call number translation profile for outgoing calls Dial peer CUCM uses dial-peer to route the call based on the digit to route the call accordingly. incoming voice call to CUCM dial-peer voice 1 voip destination-pattern session protocol sipv2 session target ipv4: voice-class codec 1 voice-class sip early-offer forced dtmf-relay rtp-nte Page 9 of 58

10 ip qos dscp cs5 media ip qos dscp cs4 signaling no vad for outgoing calls to Cox ESBC dial-peer voice 10 voip description **NA 11 digits dial** destination-pattern 1[2-9]..[2-9]... session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media ip qos dscp cs4 signaling no vad dial-peer voice 11 voip description **NA 10 digits** destination-pattern [2-9]..[2-9]... session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media ip qos dscp cs4 signaling no vad Page 10 of 58

11 dial-peer voice 13 voip description **0 or 00 calls to Local or International Operator** destination-pattern 0T session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip dtmf-relay force rtp-nte voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media ip qos dscp cs3 signaling no vad dial-peer voice 12 voip description **NA international call** destination-pattern 011T session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media ip qos dscp cs4 signaling no vad dial-peer voice 14 voip description **CCA*North American-3-Digit*Service Numbers** destination-pattern [2-9]11 session protocol sipv2 Page 11 of 58

12 session target sip-server voice-class codec 1 voice-class sip dtmf-relay force rtp-nte voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs3 signaling no vad dial-peer voice 15 voip description **Dial Carrier Access Code** destination-pattern [2-9]..[2-9]... session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip dtmf-relay force rtp-nte no voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs3 signaling no vad outgoing fax call dial-peer voice 100 voip description outgoing fax to COX translation-profile outgoing DIGITSTRIP8 destination-pattern session protocol sipv2 session target sip-server codec g711ulaw ip qos dscp af32 signaling Page 12 of 58

13 Call flow In the sample configuration presented here, CUCM is provisioned with four-digit directory numbers corresponding to the last four DID digits. No digit manipulation is performed on the CUBE. For incoming PSTN calls, the CUBE presents the full ten-digit DID number to CUCM. The CUCM Translation Pattern strips all but the last four digits and routes the call based on those digits. Voice calls are routed to IP phones; fax calls are routed via a 4-digit route pattern to a SIP trunk that terminates on the VG224 CPE callers make outbound PSTN calls by dialing a 9 prefix followed by the destination number. For outbound fax calls from the analog fax endpoint, VG224 translate leading access code 9 to 8. A 9.@ route pattern strips the prefix and routes the call with the remaining digits via a SIP trunk terminating on the CUBE for Voice call, and 8.@ Route Pattern send all digits to CUBE to use different dial peer and remove the leading digit 8 and send to Cox network for outbound Fax. Figure 2: Outbound Voice Call Figure 3: Outboud Fax Call Configuration example The following configuration snippet contains a sample configuration of Cisco Unified Border Element with all parameters mentioned previously. Last configuration change at 19:43:58 UTC Tue May by cisco Page 13 of 58

14 version 15.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption hostname COX_CUBE boot-start-marker boot-end-marker aqm-register-fnf logging buffered warnings enable secret 4 tnhtc92dxbhelxjyk8lwjrpv36s2i4ntxrpb4rfmfqy no aaa new-model no ip domain lookup ip name-server ip cef Page 14 of 58

15 no ipv6 cef multilink bundle-name authenticated password encryption aes crypto pki trustpoint TP-self-signed enrollment selfsigned subject-name cn=ios-self-signed-certificate revocation-check none rsakeypair TP-self-signed crypto pki certificate chain TP-self-signed certificate self-signed B A D0609 2A F70D F30 2D F532D 53656C66 2D E65642D D E 170D A17 0D A F302D F532D53 656C662D E 65642D D F 300D0609 2A F70D D AC64 457DC FE0 A1AD6097 4F1358E1 3721B264 13A1D71B D711054C F27B071E 91464C54 EACBD884 DC242E08 1BC34A7E 1FA49C2F 4A130BD1 461AC476 BA1352B7 F54C E43E 1FF4824D 8A75A247 F4AB488A 3F9EFD9C 6CED7728 4CE96D86 B43594A1 6684B A 99F337D9 5C04D4D6 ECD7BA8C Page 15 of 58

16 1AEF A F D FF FF 301F D B70ED5 6EF1FA77 9D2F8B0B 644BF4DE BC 27301D D0E B70ED56E F1FA779D 2F8B0B64 4BF4DE BC27 300D0609 2A F70D E882FC60 E29C53FE 5A B1A C03D7 677F2A10 178A4A9A B83448B1 EFBC136A 4080D4FC 493C3CDB 623B6343 A3639AEB 2A7753B8 9DFB4C79 F3BF9E03 A3146AA0 11AA9FC1 9F E4D57CB 78413BD3 10C790EE CBBBE796 A8490BE1 D0524A DC8B 91E6A14C 6FAF8DB F 425B3B8C quit voice-card 0 dsp services dspfarm voice rtp send-recv voice service voip ip address trusted list ipv ipv address-hiding mode border-element allow-connections sip to sip no supplementary-service sip refer fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw sip asserted-id pai privacy pstn early-offer forced midcall-signaling passthru Page 16 of 58

17 sip-profiles 1 voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw voice class sip-profiles 1 request INVITE sip-header SIP-Req-URI modify "; SIP/2.0" ";user=phone SIP/2.0" request REINVITE sip-header SIP-Req-URI modify "; SIP/2.0" ";user=phone SIP/2.0" request INVITE sip-header Contact modify ">" ";user=phone>" request REINVITE sip-header Contact modify ">" ";user=phone>" request INVITE sip-header To modify ">" ";user=phone>" request REINVITE sip-header To modify ">" ";user=phone>" request INVITE sip-header From modify ">" ";user=phone>" request REINVITE sip-header From modify ">" ";user=phone>" voice translation-rule 1 rule 1 /^8\(.*\)/ /\1/ voice translation-profile DIGITSTRIP8 translate called 1 Page 17 of 58

18 license udi pid C3900-SPE250/K9 sn FOC17426ADY hw-module pvdm 0/0 username cisco privilege 15 password D C40 redundancy interface GigabitEthernet0/0 description COX Cisco CUCM9.1.2 test CUBE ip address duplex auto speed auto interface GigabitEthernet0/1 ip address duplex auto speed auto interface GigabitEthernet0/2 no ip address shutdown Page 18 of 58

19 duplex auto speed auto interface GigabitEthernet0/3 no ip address shutdown duplex auto speed auto ip forward-protocol nd ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life requests ip route ip route nls resp-timeout 1 cpd cr-id 1 control-plane Page 19 of 58

20 mgcp behavior rsip-range tgcp-only mgcp behavior comedia-role none mgcp behavior comedia-check-media-src disable mgcp behavior comedia-sdp-force disable mgcp profile default dial-peer voice 1 voip destination-pattern session protocol sipv2 session target ipv4: voice-class codec 1 voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media ip qos dscp cs4 signaling no vad dial-peer voice 10 voip description **NA 11 digits dial** destination-pattern 1[2-9]..[2-9]... session protocol sipv2 session target sip-server Page 20 of 58

21 voice-class codec 1 voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media ip qos dscp cs4 signaling no vad dial-peer voice 11 voip description **NA 10 digits** destination-pattern [2-9]..[2-9]... session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media ip qos dscp cs4 signaling no vad dial-peer voice 13 voip description **0 or 00 calls to Local or International Operator** destination-pattern 0T session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip dtmf-relay force rtp-nte voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media Page 21 of 58

22 ip qos dscp cs3 signaling no vad dial-peer voice 12 voip description **NA international call** destination-pattern 011T session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs5 media ip qos dscp cs4 signaling no vad dial-peer voice 14 voip description **CCA*North American-3-Digit*Service Numbers** destination-pattern [2-9]11 session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip dtmf-relay force rtp-nte voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs3 signaling no vad dial-peer voice 15 voip description **Dial Carrier Access Code** Page 22 of 58

23 destination-pattern [2-9]..[2-9]... session protocol sipv2 session target sip-server voice-class codec 1 voice-class sip dtmf-relay force rtp-nte no voice-class sip early-offer forced dtmf-relay rtp-nte ip qos dscp cs3 signaling no vad dial-peer voice 100 voip description outgoing fax to COX translation-profile outgoing DIGITSTRIP8 destination-pattern session protocol sipv2 session target sip-server codec g711ulaw ip qos dscp af32 signaling sip-ua sip-server ipv4: :5060 gatekeeper shutdown Page 23 of 58

24 telephony-service max-conferences 8 gain -6 transfer-system full-consult after-hours block pattern after-hours day Sun 00:00 23:59 after-hours day Mon 00:00 23:59 after-hours day Tue 00:00 23:59 after-hours day Wed 00:00 23:59 after-hours day Thu 00:00 23:59 after-hours day Fri 00:00 23:59 after-hours day Sat 00:00 23:59 line con 0 exec-timeout 0 0 password F41 logging synchronous login local line aux 0 line vty 0 4 exec-timeout 0 0 password F0725 logging synchronous login local transport input telnet ssh line vty 5 15 exec-timeout 0 0 logging synchronous Page 24 of 58

25 login local transport input telnet ssh scheduler allocate ntp server end Page 25 of 58

26 Configuring the Cisco Unified Communications Manager Cisco CallManager service parameter Go to System > Service Parameters.we leave all fields in the service parameter as default values for this test Figure 4Service Parameter Page 26 of 58

27 Figure 5 Service Parameter Cont. Page 27 of 58

28 Figure 6 Service Parameter Cont. Page 28 of 58

29 Figure 7 Service Parameter Cont. Page 29 of 58

30 Figure 8 Service Paramater Cont. Page 30 of 58

31 Figure 9 Service Parameter Cont. Page 31 of 58

32 Figure 10 Service Parameter Cont. Page 32 of 58

33 Figure 11 Service Parameter Cont. Page 33 of 58

34 Figure 12 Service Parameter Cont. Page 34 of 58

35 Figure 13 Service Parameter Cont. Page 35 of 58

36 Figure 14 Service Parameter Cont. Page 36 of 58

37 Figure 15 Service parameter Cont. Page 37 of 58

38 Figure 16 Service Parameter Cont. Page 38 of 58

39 Device Pool, Region and Audio Codec Preference List Navigate to System > Device Pool and click on Add New to create the Device Pool Navigate to System >Region Information>Audio Codec Preference List to create Codec Preference List Navigate to System >Region Information>Region to create Region In our test, we are using the default Factory Default low loss for Audio Codec Preference List, Default for Region and Device Pool. Figure 17 Device Pool Figure 18 Audio Codec Preference List Page 39 of 58

40 Figure 19 Region Page 40 of 58

41 Offnet calls via Cox SIP Trunk Off-net calls are served by SIP trunks configured between CUCM and Cox ESBC. Calls are routed via CUBE. SIP Trunk Security Profile Go to System > Security > SIP Trunk Security Profile and click on Add New. The default Non Secure SIP Trunk Profile is used in this test Figure 20 SIP Trunk Security Profile Parameter Value Description Incoming Transport Type TCP + UDP Outgoing Transport Type UDP SIP trunks to Cox ESBC should use UDP as a transport protocol for SIP. This is configured using SIP Trunk Security profile, which is later assigned to the SIP trunk itself. Page 41 of 58

42 SIP Profile SIP Profile will be later associated with the SIP trunk. Navigate to Device > Device Settings > SIP Profile and modify default SIP Profile by clicking on a Copy button in its row. Figure 21 SIP Profile Page 42 of 58

43 Figure 22 SIP Profile Cont. Page 43 of 58

44 Parameter Value Description Default MTP Telephony Event Payload Type 101 RFC2833 DTMF payload type Require SDP Inactive Exchange for Mid-Call Media Change SIP Rel1XX Options Checked Send PRACK for 1xx Messages Send SDP with Inactive when call on hold Enable Provisional Acknowlesgements (Reliable 100 messages) Ping Interval for In-service and Partially In-service Trunks (seconds) Ping Interval for Out-of-service Trunks (seconds) 300 OPTIONS message parameters- interval time 5 OPTIONS message parameters- interval time Page 44 of 58

45 SIP Trunk Configuration Create SIP trunks to Cox by navigating to Device > Trunk and clicking Add New button. Same apply to create Sip trunks to Cisco Unity Connection and VG224 Figure 23 SIP Trunks List Page 45 of 58

46 Figure 24 SIP Trunk to CUBE Page 46 of 58

47 Figure 25 SIP Trunk to CUBE Cont. Page 47 of 58

48 Figure 26 SIP Trunk to CUBE Cont. Page 48 of 58

49 Parameter Value Description Device Name Cox Name for the trunk Device Pool Default Default Device Pool is used for this trunk Media Resource Group List MRGL_MTP MRG with resources:ann, CFB, MOH and MTP Significant Digits 4 4 digits Extension for all CPE phones Redirecting Diversion Header Delivery - outbound Checked Adding Diversion Header for calls outband from site Destination Address LAN IP address of the CUBE SIP Trunk Security Profile Non Secure SIP Trunk Profile SIP Trunk Security Profile configured earlier SIP Profile Cox SIP Profile SIP Profile configured earlier DTMF Signaling Method RFC 2833 RFC 2833 is supported for DTMF transport to/from Cox Reset the trunk after the configuration is completed. Apply same procedure to create SIP trunks to Cisco Unity Connection and VG224 Page 49 of 58

50 Dialplan Translation pattern Configuration CUBE send 10 digits number as dialed digits to CUCM, need to configure Translation Pattern to strip the leading 6 digits so the call can deliver to the 4 digits extension. Navigation to Call Routing > Translation Pattern > Add New Figure 27 Translation Pattern Page 50 of 58

51 Setting Value Description Translation pattern XXXX Incoming called number Pattern from Cox Discard Digits PreDot specifies how to modify digit before they are sending to CUBE and then to Cox Route Pattern configuration Route patterns are configured as below, Cisco IP phone dial 9+10digits number to access PSTN via CUBE, 9 is removed before send to CUBE; for FAX call, Access Code 9 is translate to 8 at VG224 and 8+10digits number is send to CUBE to use different dial peer to Cox network. Incoming fax call to 3710 will send to VG is the Pilot Number for Voice mail to Unity Connection. Navigate to Call Routing > Route/Hunt > Route Pattern and press Add New button to create Route Patterns Figure 28 Route Pattern Page 51 of 58

52 Figure 29 Route Pattern for Voice Page 52 of 58

53 Figure 30 Route Pattern for Fax Page 53 of 58

54 Setting Value Description Route Pattern for Voice call and for fax call Specify appropriate Route Pattern Gateway/Route List COX SIP Trunk name configured earlier Require Forced Authorization Code Require Client Matter Code Checked when doing Authorization Code test Check when doing Account Code test Specify if Authorization Code required when make call through this Route Pattern Specify if Account Code required when make call through this Route Pattern Calling Party Transform mask XXXX Specify the Calling Line ID for outgoing call through this Route Pattern Discard Digits PreDot for RP None for Route Pattern specifies how to modify digit before they are sending to Cox ESBC Acronyms Acronym CPE CUBE CUCM MTP POP PSTN ESBC SCCP SIP Definitions Customer Premise Equipment Cisco Unified Border Element Cisco Unified Communications Manager Media Termination Point Point of Presence Public Switched Telephone Network Enterprise Session Border Controller Skinny Client Control Protocol Session Initiation Protocol Page 54 of 58

55 Important Information THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Page 55 of 58

56 Appendix A: Test Results Application Note ServiceProvider_Det ailed_test_plan.doc Page 56 of 58

57 Corporate Headquarters European Headquarters Americas Headquarters Asia Pacific Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA Tel: NETS (6387) Fax: Cisco Systems International BV Haarlerbergpark Haarlerbergweg CH Amsterdam The Netherlands www-europe.cisco.com Tel: Fax: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA Tel: Fax: Cisco Systems, Inc. Capital Tower 168 Robinson Road #22-01 to #29-01 Singapore Tel: Fax: Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on the Cisco Web site at Argentina Australia Austria Belgium Brazil Bulgaria Canada Chile China PRC Colombia Costa Rica Croatia Czech Republic Denmark Dubai, UAE Finland France Germany Greece Hong Kong SAR Hungary India Indonesia Ireland Israel Italy Japan Korea Luxembourg Malaysia Mexico The Netherlands New Zealand Norway Peru Philippines Poland Portugal Puerto Rico Romania Russia Saudi Arabia Scotland Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Turkey Ukraine United Kingdom United States Venezuela Vietnam Zimbabwe 2008 Cisco Systems, Inc. All rights reserved. CCENT, Cisco Lumin, Cisco Nexus, the Cisco logo and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCVP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iphone, iq Expertise, the iq logo, iq Net Readiness Scorecard, iquick Study, LightStream, Linksys, MeetingPlace, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath Page 57 of 58

58 are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R) Printed in the USA Page 58 of 58