Configurazione Rete VoIP

Size: px
Start display at page:

Download "Configurazione Rete VoIP"

Transcription

1 Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul CISCO 3725 Router 3725 Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9_SNA-M), Version 12.4(25d), RELEASE SOFTWARE (fc1) with 64Mbit di Flash Format flash: del Router R1#copy run flash: Destination filename [r1-confg]? Erase flash: before copying? [confirm]n Verifying checksum... OK (0x6C65) 901 bytes copied in secs (302 bytes/sec) R1#format flash: Format operation may take a while. Continue? [confirm] Format operation will destroy all data in "flash:". Continue? [confirm] Ing. Nicola Cappuccio info@studiocappuccio.net 1

2 Current Low End File System flash card in flash will be formatted into DOS File System flash card Continue? [confirm] Format: Drive communication & 1st Sector Write OK... Writing Monlib sectors Monlib write complete Format: All system sectors written. OK... Format: Total sectors in formatted partition: Format: Total bytes in formatted partition: Format: Operation completed successfully. Format of flash complete interfaces Fastethernet 0/ /24 Operazioni preliminari sul PC Abilitare un interfaccia di loopback /24 e collegare via Ethernet il pc ed il 7940G Abilitare il server TFTP sull indirizzo di loopback /24 Download via TFTP del cme-full tar from PC to CISCO Router router#archive tar /xtract tftp://<local host>/cme-full tar flash: Configurare DHCP su CISCO 3725 Abilititare server dhcp router# configure terminal router (config)# ip dhcp excluded-address router (config)# ip dhcp pool VOICE_SCOPE router (dhcp-config)# network router (dhcp-config)# default-router router (dhcp-config)# option 150 ip router (dhcp-config)# dns-server Ing. Nicola Cappuccio info@studiocappuccio.net 2

3 Abilitare il debug router#debug ip dhcp server events Configurare I Servizi Telefonici router # dir flash:/phone/ Directory of flash:/phone/ / Laboratorio 24/11/ rw May :33:56-07:00 P bin 99 -rw- 458 May :33:56-07:00 P loads 100 -rw May :34:00-07:00 P sb rw May :34:00-07:00 P sbn bytes total ( bytes free) router # configure terminal Enter configuration commands, one per line. End with CNTL/Z. router (config)# tftp-server flash:/phone/ /p bin alias P bin router (config)# tftp-server flash:/phone/ /p loads alias P loads router (config)# tftp-server flash:/phone/ /p sb2 alias P sb2 router (config)# tftp-server flash:/phone/ /p sbn alias P sbn router (config)# telephony-service router (config-telephony)# ip source-address router(config-telephony)#create cnf-files router (config-telephony)#do sh flash -#- --length date/time path 1 0 Mar :58:18 +01:00 bacdprompts Mar :00:12 +01:00 phone 47 0 Mar :00:12 +01:00 phone/ Mar :00:16 +01:00 phone/ /p bin Mar :00:16 +01:00 phone/ /p loads Ing. Nicola Cappuccio info@studiocappuccio.net 3

4 Mar :00:42 +01:00 phone/ /p sb Mar :00:46 +01:00 phone/ /p sbn. router(config-telephonyr)#load P Updating CNF files CNF files updating complete router(config-telephonyr)#reset sequence-all router(config-telephony)#create cnf-files router(config-telephony)#reset sequence-all router(config-telephony)#exit router (config-telephony)# max-ephones? <1-30> Maximum phones to support router (config-telephony)# max-ephones 10 router (config-telephony)# max-dn? <1-150> Maximum directory numbers supported <cr> router (config-telephony)# max-dn 10 router (config)#ephone-dn 1 router (config-ephone-dn)#number 1000 router (config-ephone-dn)#exit router (config)#ephone-dn 2 router (config-ephone-dn)#number 2000 router (config-ephone-dn)#exit router # show ephone */restituisce la lista degli ephone presenti sulla rete con il mac-address */associazione IP-Phone Numeri e Linee router (config)# ephone 1 router (config-ephone)# mac-address XXXX.XXXX.XXXX router (config-ephone)# button 1:1 router (config-ephone)# restart Ing. Nicola Cappuccio info@studiocappuccio.net 4

5 router (config-ephone)# exit router (config)# ephone 2 Laboratorio 24/11/2014 router (config-ephone)# mac-address YYYY.YYYY.YYYY router (config-ephone)# button 1:1 router (config-ephone)# restart router (config-ephone)# exit Setting the Clock of a Cisco Device with NTP router #clock set 11:13:00 28 Nov 2014 router # *Nov 28 11:13:00.000: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:01:13 UTC Fri Mar to 11:13:00 UTC Fri Nov , configured from console by console. router # router #configure terminal router (config)#ntp server router (config)#clock timezone ITALY +1 router (config)#ntp master Startup-config 3725 Last configuration change at 02:08:08 ITALY Fri Mar NVRAM config last updated at 02:27:07 ITALY Fri Mar version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname R1 boot-start-marker boot-end-marker Ing. Nicola Cappuccio info@studiocappuccio.net 5

6 no aaa new-model memory-size iomem 5 clock timezone ITALY 1 no ip icmp rate-limit unreachable ip cef no ip dhcp use vrf connected ip dhcp excluded-address ip dhcp pool VOICE_SCOPE network default-router option 150 ip no ip domain lookup ip auth-proxy max-nodata-conns 3 ip admission max-nodata-conns 3 ip tcp synwait-time 5 ip ssh version 1 interface FastEthernet0/0 ip address duplex auto speed auto interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ip forward-protocol nd Ing. Nicola Cappuccio info@studiocappuccio.net 6

7 no ip http server no ip http secure-server no cdp log mismatch duplex tftp-server flash:/phone/ /p bin alias P bin tftp-server flash:/phone/ /p loads alias P loads tftp-server flash:/phone/ /p sb2 alias P sb2 tftp-server flash:/phone/ /p sbn alias P sbn control-plane telephony-service load P max-ephones 10 max-dn 10 ip source-address port 2000 create cnf-files version-stamp 7960 Mar :38:27 max-conferences 8 gain -6 ephone-dn 1 number 1000 ephone-dn 2 number 2000 ephone 1 mac-address 001F.6C80.7F50 button 1:1 ephone 2 mac-address C4F.4F50 button 1:2 line con 0 exec-timeout 0 0 privilege level 15 logging synchronous line aux 0 exec-timeout 0 0 privilege level 15 logging synchronous line vty 0 4 Ing. Nicola Cappuccio info@studiocappuccio.net 7

8 login ntp master 1 ntp server end Laboratorio 24/11/2014 Application Note 7940G direttamente connesso alla porta Ethernet del PC. Disattivare windows firewall Ing. Nicola Cappuccio info@studiocappuccio.net 8

Configurazione Rete VoIP

Configurazione Rete VoIP Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul

More information

CS3695/M6-109 Lab 8-NPS02 VOIP Sniffing Ver. 8 Rev. 0

CS3695/M6-109 Lab 8-NPS02 VOIP Sniffing Ver. 8 Rev. 0 Background For this lab, we will be analyzing some Wireshark capture files that were captured using the ARP Poisoning technique on Cisco VIOP (Voice Over IP) phones As this lab took special equipment (i.e.

More information

Lab Configuring Syslog and NTP (Instructor Version)

Lab Configuring Syslog and NTP (Instructor Version) (Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask

More information

Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration

Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration Summary This setup covers the of the TEAM VoWLAN solution with a Cisco Communications Manager Express 4.1 +. This integration

More information

Lab 5.3.9b Managing Router Configuration Files Using TFTP

Lab 5.3.9b Managing Router Configuration Files Using TFTP Lab 5.3.9b Managing Router Configuration Files Using TFTP Device Host Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Download and install TFTP server software.

More information

Case Study 1: Registering IP Phones with a remote Call

Case Study 1: Registering IP Phones with a remote Call Case Study 1: Registering IP Phones with a remote Call Manager Objectives Place calls from IP Phones under R1 to IP Phones under R2 Place calls from any IP Phone (under R1 and under R2) to the regular

More information

Simple MPLS network topology for Dynamips/Olive

Simple MPLS network topology for Dynamips/Olive Simple MPLS network topology for Dynamips/Olive R1 version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname R1 boot-start-marker

More information

Lab 6.1.3 Configure Local AAA on Cisco Router

Lab 6.1.3 Configure Local AAA on Cisco Router Lab 6.1.3 Configure Local AAA on Cisco Router Objective Scenario Topology In this lab, the students will complete the following tasks: Securing and testing access to the privileged EXEC, VTY, and console

More information

Lab 8.4.3b Managing Cisco IOS images with ROMMON and TFTP

Lab 8.4.3b Managing Cisco IOS images with ROMMON and TFTP Lab 8.4.3b Managing Cisco IOS images with ROMMON and TFTP Host Device Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Analyze the Cisco IOS image and router

More information

Managing and Configuring Cisco VoIP Devices

Managing and Configuring Cisco VoIP Devices CHAPTER 3 Managing and Configuring Cisco Vo Devices This chapter examines how to configure Vo using a variety of methods: Vo telephony setup dialog, manual configuration of the router for Cisco CallManager

More information

Brest. Backup : copy flash:ppe_brest1 running-config

Brest. Backup : copy flash:ppe_brest1 running-config Brest Backup : copy flash:ppe_brest1 running-config Cisco SF300-08 Mise en place des services : - Serveurs : 10.3.50.0/24 VLAN 2 (port 1) - DSI : 10.3.51.0/24 VLAN 3 (port 2) - Direction : 10.3.52.0/24

More information

ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability

ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability 6AOSSG0007-42A March 2013 Interoperability Guide ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability

More information

Planning Maintenance for Complex Networks

Planning Maintenance for Complex Networks Planning Maintenance for Complex Networks CCNP TSHOOT: Maintaining and Troubleshooting IP Networks Olga Torstensson TSHOOT v6 1 Maintenance Models and Methodologies A network engineer s job description

More information

Table of Contents. Cisco Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others

Table of Contents. Cisco Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others Cisco IOS Firewall to Allow Java Applets From Known Sites w Table of Contents Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others...1 Introduction...1 To Deny Java

More information

Chapter 1: Planning Maintenance for Complex Networks. TSHOOT v6 Chapter 1 2007 2010, Cisco Systems, Inc. All rights reserved.

Chapter 1: Planning Maintenance for Complex Networks. TSHOOT v6 Chapter 1 2007 2010, Cisco Systems, Inc. All rights reserved. : Planning Maintenance for Complex Networks CCNP TSHOOT: Maintaining and Troubleshooting IP Networks TSHOOT v6 1 Objectives Evaluate commonly-practiced models and methodologies for network maintenance

More information

How To Configure A Cisco Router With A Cio Router

How To Configure A Cisco Router With A Cio Router CHAPTER 1 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also

More information

Lab 2.1 Configure CME using the CLI and Cisco IP Communicator

Lab 2.1 Configure CME using the CLI and Cisco IP Communicator Lab 2.1 Configure CME using the CLI and Cisco IP Communicator Learning Objectives Configure Cisco Unified Call Manager Express (CME) Install Cisco IP Communicator (CIPC) on a host Verify CME and CIPC Operation

More information

Skills Assessment Student Training (Answer Key)

Skills Assessment Student Training (Answer Key) CCNA: Connecting Networks Skills Assessment Student Training (Answer Key) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Assessment

More information

Guaranteeing QoS in a Crises Response

Guaranteeing QoS in a Crises Response Technical report, IDE1142, June 2011 Guaranteeing QoS in a Crises Response Network Master s Programme in Computer Networks Engineering Muhammad Salman & Muhammad Mobeen Ahmed School of Information Science,

More information

Configuring Fax Pass-Through

Configuring Fax Pass-Through Configuring Fax Pass-Through This chapter describes the configuration of fax pass-through. With fax pass-through, modulated fax information from the PSTN is passed in-band over a voice speech path in an

More information

Lab 11.5.6.1 Configure Syslog on AP

Lab 11.5.6.1 Configure Syslog on AP Lab 11.5.6.1 Configure Syslog on AP Estimated Time: 25 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, students will configure and use syslog logging to monitor

More information

Integrated Data and Voice Services for ISDN PRI Interfaces on Multiservice Access Routers

Integrated Data and Voice Services for ISDN PRI Interfaces on Multiservice Access Routers Integrated Data and Voice Services for ISDN PRI Interfaces on Multiservice Access Routers This chapter describes how to configure ISDN PRI interfaces to support the integration of data and voice calls

More information

The Cisco IOS Firewall feature set is supported on the following platforms: Cisco 2600 series Cisco 3600 series

The Cisco IOS Firewall feature set is supported on the following platforms: Cisco 2600 series Cisco 3600 series Cisco IOS Firewall Feature Set Feature Summary The Cisco IOS Firewall feature set is available in Cisco IOS Release 12.0. This document includes information that is new in Cisco IOS Release 12.0(1)T, including

More information

Cisco Routers and Switches

Cisco Routers and Switches Cisco Routers and Switches Phoenix Cisco User Group (PCUG) Tools, tips, and tricks you never knew Hello! Jeremy D. Cioara - CCIE, MCSE, CNE AdTEC Networks - Chief Information Officer Cisco IP Telephony

More information

Lab 8.4.3a Managing Cisco IOS Images with TFTP

Lab 8.4.3a Managing Cisco IOS Images with TFTP Lab 8.4.3a Managing Cisco IOS Images with TFTP Host Device Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Analyze the Cisco IOS image and router flash memory.

More information

Configuring a Cisco 2509-RJ Terminal Router

Configuring a Cisco 2509-RJ Terminal Router created by: Rainer Bemsel Version 1.0 Dated: Dec/08/2012 For my Cisco LAB, I ve purchased a used Cisco 2509-RJ with RJ45-RJ45 roll-over cables. This TechTip shows my configuration setup, so you can easily

More information

TotalCloud Phone System

TotalCloud Phone System TotalCloud Phone System Cisco SF 302-08P PoE VLAN Configuration Guide Note: The below information and configuration is for deployment of the Cbeyond managed switch solution using the Cisco 302 8 port Power

More information

CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA. Switch S1 S1#sh ru Building configuration...

CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA. Switch S1 S1#sh ru Building configuration... CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA Switch S1 S1#sh ru Building configuration... Current configuration : 1639 bytes version 12.2 no service timestamps log datetime

More information

Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering

Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering 7.1 Details Aim: Rich Macfarlane The aim of this lab is to introduce the concepts of stateful firewalls, using Cisco Contextbased Access Control

More information

Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router

Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue este capítulo Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue el libro completo

More information

642-437. Implementing Cisco Unified Communications Voice over IP and QoS v8.0 (CVOICE v8.0) Version: Demo. Page <<1/8>>

642-437. Implementing Cisco Unified Communications Voice over IP and QoS v8.0 (CVOICE v8.0) Version: Demo. Page <<1/8>> 642-437 Implementing Cisco Unified Communications Voice over IP and QoS v8.0 (CVOICE v8.0) Version: Demo Page 1. Which three Cisco IOS commands are required to configure a voice gateway as a DHCP

More information

Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500

Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500 Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500 Objective Use Cisco Discovery Protocol (CDP) commands to get information about neighboring network devices. Background/Preparation CDP

More information

- Basic Router Security -

- Basic Router Security - 1 Enable Passwords - Basic Router Security - The enable password protects a router s Privileged mode. This password can be set or changed from Global Configuration mode: Router(config)# enable password

More information

LAN-Cell to Cisco Tunneling

LAN-Cell to Cisco Tunneling LAN-Cell to Cisco Tunneling Page 1 of 13 LAN-Cell to Cisco Tunneling This Tech Note guides you through setting up a VPN connection between a LAN-Cell and a Cisco router. As the figure below shows, the

More information

3.1 Connecting to a Router and Basic Configuration

3.1 Connecting to a Router and Basic Configuration 3.1 Connecting to a Router and Basic Configuration Objective This lab will focus on the ability to connect a PC to a router in order to establish a console session and observe the user interface. A console

More information

Connecting to the Firewall Services Module and Managing the Configuration

Connecting to the Firewall Services Module and Managing the Configuration CHAPTER 3 Connecting to the Firewall Services Module and This chapter describes how to access the command-line interface and work with the configuration. This chapter includes the following sections: Connecting

More information

Configuring Basic Broadband Internet Access

Configuring Basic Broadband Internet Access CHAPTER 4 This chapter describes the parameters of configuring and maintaining basic broadband Internet access. The chapter contains these sections: Overview of Basic Broadband Internet Access section

More information

Objectives. Background. Required Resources. CCNA Security

Objectives. Background. Required Resources. CCNA Security Chapter 8 Lab B, Configuring a Remote Access VPN Server and Client Topology IP Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1 192.168.1.1 255.255.255.0 N/A

More information

Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example

Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example Document ID: 113337 Contents Introduction Prerequisites Requirements Components Used Conventions Configuration

More information

Configuring Voice and Data Support on VWIC3s

Configuring Voice and Data Support on VWIC3s First Published: July 21, 2010, OL-22847-01 This module describes how to configure voice and data support on the next generation of voice/wan Interface Cards (VWICs) also known as VWIC3s. The following

More information

Skills Assessment Student Training Exam

Skills Assessment Student Training Exam Skills Assessment Student Training Exam Topology Assessment Objectives Part 1: Initialize Devices (8 points, 5 minutes) Part 2: Configure Device Basic Settings (28 points, 30 minutes) Part 3: Configure

More information

Configuring Devices for Use with Cisco Configuration Professional (CCP) 2.5

Configuring Devices for Use with Cisco Configuration Professional (CCP) 2.5 Configuring Devices for Use with Cisco Configuration Professional (CCP) 2.5 Objectives Part 1: Configure CCP Access for Routers Enable HTTP/HTTPS server. Create a user account with privilege level 15.

More information

Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.

Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H. Application Note Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.323 Gateway Introduction This document describes the interoperability

More information

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNP: Optimizing

More information

Lab 8.3.1.2 Configure Basic AP Security through IOS CLI

Lab 8.3.1.2 Configure Basic AP Security through IOS CLI Lab 8.3.1.2 Configure Basic AP Security through IOS CLI Estimated Time: 30 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, the student will learn the following

More information

BRI to PRI Connection Using Data Over Voice

BRI to PRI Connection Using Data Over Voice BRI to PRI Connection Using Data Over Voice Document ID: 14962 Contents Introduction Prerequisites Requirements Conventions Background Information Configure Network Diagram Configurations Verify Troubleshoot

More information

Connect the Host to attach to Fast Ethernet switch port Fa0/2. Configure the host as shown in the topology diagram above.

Connect the Host to attach to Fast Ethernet switch port Fa0/2. Configure the host as shown in the topology diagram above. Lab 1.2.2 Capturing and Analyzing Network Traffic Host Name IP Address Fa0/0 Subnet Mask IP Address S0/0/0 Subnet Mask Default Gateway RouterA 172.17.0.1 255.255.0.0 192.168.1.1 (DCE) 255.255.255.0 N/A

More information

Lab 7.2.9 Load Balancing Across Multiple Paths Instructor Version 2500

Lab 7.2.9 Load Balancing Across Multiple Paths Instructor Version 2500 Lab 7.2.9 Load Balancing Across Multiple Paths Instructor Version 2500 Objective onfigure Load balance across multiple paths. Observe the load balancing process. Background/Preparation able a network similar

More information

Proposal for implementation of VoIP at XYZ hospital.

Proposal for implementation of VoIP at XYZ hospital. Proposal for implementation of VoIP at XYZ hospital. Introduction Management committee of XYZ hospital wants to implement an internal voice communication system for their hospital. At present they are

More information

Configuring a Leased Line

Configuring a Leased Line CHAPTER 4 Configuring a Leased Line The configuration in this chapter describes how to configure a Cisco 1700 router for IP and IPX over a synchronous serial line. Before You Begin The configuration in

More information

Enabling Management Protocols: NTP, SNMP, and Syslog

Enabling Management Protocols: NTP, SNMP, and Syslog SECTION 7 Enabling Management Protocols: NTP, SNMP, and Syslog In this Section This section describes how to enable basic management protocols on a Cisco AS5800 and Cisco AS5300 as part of a dial access

More information

ICND1 Lab Guide. 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0. Labs powered by

ICND1 Lab Guide. 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0. Labs powered by ICND1 Lab Guide 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0 ii Interconnecting Cisco Networking Devices Part 1 100-101 Lab Guide LM20130929/BV2.01 iii 25 Century Blvd. Ste. 500

More information

System Components PBX Model. Configuration Tasks

System Components PBX Model. Configuration Tasks Cisco 3600 Series Gateway-PBX Interoperability: Lucent Definity G3 with T1 PRI Signaling This document describes the interoperability and configuration of a Cisco 3600 series voice gateway with a Lucent

More information

Felix Rohrer. PT Activity 7.5.3: Troubleshooting Wireless WRT300N. Topology Diagram

Felix Rohrer. PT Activity 7.5.3: Troubleshooting Wireless WRT300N. Topology Diagram Felix Rohrer PT Activity 7.5.3: Troubleshooting Wireless WRT300N Topology Diagram All contents are Copyright 1992 2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

More information

Output Interpreter. SHOW RUNNING-CONFIG SECURITY Analysis SHOW RUNNING-CONFIG - FW Analysis. Back to top

Output Interpreter. SHOW RUNNING-CONFIG SECURITY Analysis SHOW RUNNING-CONFIG - FW Analysis. Back to top Output Interpreter You have chosen to display errors warnings general information, and helpful references. Headings are displayed for all supported commands that you submitted. SHOW RUNNING-CONFIG SECURITY

More information

and 2, implemented With Cisco Unified Border Control Element (CUBE)

and 2, implemented With Cisco Unified Border Control Element (CUBE) www.xo.com XO SIP Service Customer Configuration Guide for Cisco Unified Communications Manager (CUCM) 8.0.3 XO SIP Packages 1 and 2, implemented With Cisco Unified Border Control Element (CUBE) 1 PRODUCT

More information

Chapter 8 Lab B: Configuring a Remote Access VPN Server and Client

Chapter 8 Lab B: Configuring a Remote Access VPN Server and Client Chapter 8 Lab B: Configuring a Remote Access VPN Server and Client Topology Note: ISR G2 devices have Gigabit Ethernet interfaces instead of FastEthernet Interfaces. All contents are Copyright 1992 2012

More information

Consolidated Packages and SubPackages Management

Consolidated Packages and SubPackages Management Consolidated Packages and SubPackages Management This document discusses how consolidated packages and software subpackages (individual and optional) are run and managed on the Cisco cbr Series Converged

More information

ICND1-100-101 IOS CLI Study Guide (CCENT)

ICND1-100-101 IOS CLI Study Guide (CCENT) ICND1-100-101 IOS CLI Study Guide (CCENT) Hostname: 2. hostname SW1 SWITCH CONFIGURATION Mgmt IP: 2. interface vlan 1 3. ip address 10.0.0.2 4. no shut Gateway: 2. ip default-gateway 10.0.0.1 Local User/Pwd:

More information

Objectives Understand Cisco IOS system architecture components. Work with the Cisco IOS Command Line Interface (CLI) and common commands.

Objectives Understand Cisco IOS system architecture components. Work with the Cisco IOS Command Line Interface (CLI) and common commands. Objectives Understand Cisco IOS system architecture components. Work with the Cisco IOS Command Line Interface (CLI) and common commands. Learn about Cisco IOS troubleshooting techniques. Understand upgrading

More information

Network Security Knowledge is Everything! Network Operations

Network Security Knowledge is Everything! Network Operations Network Security Knowledge is Everything Network Operations Warrick Mitchell - Network Engineer warrick.mitchell@aarnet.edu.au Agenda What is Network Security General Configuration Security Logging and

More information

- The PIX OS Command-Line Interface -

- The PIX OS Command-Line Interface - 1 PIX OS Versions - The PIX OS Command-Line Interface - The operating system for Cisco PIX/ASA firewalls is known as the PIX OS. Because the PIX product line was acquired and not originally developed by

More information

Configuring System Message Logging

Configuring System Message Logging CHAPTER 1 This chapter describes how to configure system message logging on the Cisco 4700 Series Application Control Engine (ACE) appliance. Each ACE contains a number of log files that retain records

More information

Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials.

Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials. Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials. CHAPTER 5 OBJECTIVES Configure a router with an initial configuration. Use the

More information

Lab 5.5 Configuring Logging

Lab 5.5 Configuring Logging Lab 5.5 Configuring Logging Learning Objectives Configure a router to log to a Syslog server Use Kiwi Syslog Daemon as a Syslog server Configure local buffering on a router Topology Diagram Scenario In

More information

PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations

PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations Instructor Version Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1

More information

Lab 3.5.1: Basic VLAN Configuration (Instructor Version)

Lab 3.5.1: Basic VLAN Configuration (Instructor Version) (Instructor Version) Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0

More information

Configuring a Router

Configuring a Router CHAPTER 3 Configuring a Router This chapter provides information and commands concerning the following topics: Configuring a router, specifically: Names Passwords Interfaces MOTD banners IP host tables

More information

Using LiveAction with Cisco Secure ACS (TACACS+ Server)

Using LiveAction with Cisco Secure ACS (TACACS+ Server) LiveAction Application Note Using LiveAction with Cisco Secure ACS (TACACS+ Server) September 2012 http://www.actionpacked.com Table of Contents 1. Introduction... 1 2. Cisco Router Configuration... 2

More information

Table of Contents. Cisco How to Download a Software Image to a Cisco 2600 via TFTP Using the tftpdnld ROMmon Command

Table of Contents. Cisco How to Download a Software Image to a Cisco 2600 via TFTP Using the tftpdnld ROMmon Command load a Software Image to a Cisco 2600 via TFTP Using the tftpd nd Table of Contents How to Download a Software Image to a Cisco 2600 via TFTP Using the tftpdnld ROMmon Command...1 Introduction...1 Before

More information

Cisco Configuration Professional Quick Start Guide

Cisco Configuration Professional Quick Start Guide Cisco Configuration Professional Quick Start Guide April 29, 2011 This document explains how to start using Cisco Configuration Professional Express (Cisco CP Express) and Cisco Configuration Professional

More information

Applicazioni Telematiche

Applicazioni Telematiche Angelo Coiro Laboratorio Applicazioni Telematiche L emulatore Packet Tracer Packet Tracer Cisco Packet Tracer is an academic software that allows to emulate Cisco devices Packet Tracer can be used for

More information

Basic Configuration of the Cisco 12000 Series Internet Router

Basic Configuration of the Cisco 12000 Series Internet Router CHAPTER 2 Basic Configuration of the Cisco 12000 Series Internet Router This chapter describes how to boot and configure the Cisco 12000 Series Internet Router. It discusses the following subjects: Cisco

More information

Configuring the Cisco Secure PIX Firewall with a Single Intern

Configuring the Cisco Secure PIX Firewall with a Single Intern Configuring the Cisco Secure PIX Firewall with a Single Intern Table of Contents Configuring the Cisco Secure PIX Firewall with a Single Internal Network...1 Interactive: This document offers customized

More information

Remote Access VPN Business Scenarios

Remote Access VPN Business Scenarios CHAPTER 4 This chapter explains the basic tasks for configuring an IP-based, remote access Virtual Private Network (VPN) on a Cisco 7200 series router. In the remote access VPN business scenario, a remote

More information

Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example

Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example Document ID: 45843 Introduction Prerequisites Requirements Components Used Conventions Background Information Configure Passwords

More information

Lab 5-5 Configuring the Cisco IOS DHCP Server

Lab 5-5 Configuring the Cisco IOS DHCP Server Lab 5-5 Configuring the Cisco IOS DHCP Server Learning Objectives Configure and verify the operation of the Cisco IOS DHCP server Configure an IP Helper address Review the EIGRP configuration Topology

More information

Network Security 2. Module 6 Configure Remote Access VPN

Network Security 2. Module 6 Configure Remote Access VPN 1 1 Network Security 2 Module 6 Configure Remote Access VPN 2 Learning Objectives 6.1 Introduction to Cisco Easy VPN 6.2 Configure the Easy VPN Server 6.3 Configure Easy VPN Remote for the Cisco VPN Client

More information

Lab: Basic Router Configuration

Lab: Basic Router Configuration Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Def. Gateway R1 Fa0/0 192.168.1.1 255.255.255.0 N/A S0/0/0 192.168.2.1 255.255.255.0 N/A R2 Fa0/0 192.168.3.1 255.255.255.0 N/A

More information

LAB Configuring NAT. Objective. Background/Preparation

LAB Configuring NAT. Objective. Background/Preparation LAB Configuring NAT Objective Configure a router to use network address translation (NAT) to convert internal IP addresses, typically private addresses, into outside public addresses. Configure static

More information

Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt

Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt Objective This lab may introduce new CCNP lab equipment and certain IOS features. This introductory activity also describes how to

More information

Basic Router Configuration

Basic Router Configuration CHAPTER 3 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also

More information

Secure Network Foundation Implementation Guide for Single Site Deployments

Secure Network Foundation Implementation Guide for Single Site Deployments Implementation Guide for Single Site Deployments This document provides a simple vision for a smart and secure business where everyday communications are made easier, faster, and more efficient. Cisco

More information

One-Step Lockdown with Cisco SDM

One-Step Lockdown with Cisco SDM One-Step Lockdown with Cisco SDM Router Hardening Automagically The process of turning off unnecessary services is called hardening a router to prevent attacks or exploits. The basic steps of router hardening

More information

Configuring the MNLB Forwarding Agent

Configuring the MNLB Forwarding Agent CHAPTER 3 Configuring the MNLB Forwarding Agent This chapter describes how to configure a Cisco router as an MNLB Forwarding Agent to operate in conjunction with a Cisco LocalDirector serving as Services

More information

Chapter 4: Lab A: Configuring CBAC and Zone-Based Firewalls

Chapter 4: Lab A: Configuring CBAC and Zone-Based Firewalls Chapter 4: Lab A: Configuring CBAC and Zone-Based Firewalls Topology IP Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1 192.168.1.1 255.255.255.0 N/A S1 FA0/5

More information

Validated Integrations: CUCM 10.x with xic version 4.0 SU-6 (support included for all 4.0 SU s) Version 4.08

Validated Integrations: CUCM 10.x with xic version 4.0 SU-6 (support included for all 4.0 SU s) Version 4.08 IC 4.0 SIP INTEGRATION TO CISCO UNIFIED COMMUNICATIONS MANAGER 10.X Validated Integrations: CUCM 10.x with xic version 4.0 SU-6 (support included for all 4.0 SU s) INTEGRATION DOCUMENT Version 4.08 7601

More information

Deployment Guidelines for QoS Configuration in DSL Environment

Deployment Guidelines for QoS Configuration in DSL Environment White Paper Deployment Guidelines for QoS Configuration in DSL Environment Overview In the late 1980s, DSL technology was developed to provide higher-speed digital data transmission over local telephone

More information

Basic Router Configuration Using Cisco Configuration Professional

Basic Router Configuration Using Cisco Configuration Professional Basic Router Configuration Using Cisco Configuration Professional Document ID: 111999 Contents Introduction Prerequisites Components Used Install Cisco Configuration Professional Router Configuration to

More information

LAB MANUAL for Computer Network

LAB MANUAL for Computer Network LAB MANUAL for Computer Network CSE-310 F Computer Network Lab L T P - - 3 Class Work : 25 Marks Exam : 25 MARKS Total : 50 Marks This course provides students with hands on training regarding the design,

More information

Table of Contents. Cisco Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access

Table of Contents. Cisco Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access Table of Contents Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...1 Configure...2

More information

Table of Contents. Cisco How to Download a Software Image to a Cisco 2600 through TFTP Using the tftpdnld ROMmon Command

Table of Contents. Cisco How to Download a Software Image to a Cisco 2600 through TFTP Using the tftpdnld ROMmon Command mand Table of Contents How to Download a Software Image to a Cisco 2600 through TFTP Using the tftpdnld ROMmon Command...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...1

More information

- Advanced IOS Functions -

- Advanced IOS Functions - 1 The Configuration Register - Advanced IOS Functions - The configuration register (config-register) is a hexadecimal value that controls various aspects of how a router boots, including: Baud Rate Boot

More information

Cisco IOS Voice Gateway PBX Interoperability: Avaya 8500 Communications Manager 2.1 to T1 QSIG with H.323

Cisco IOS Voice Gateway PBX Interoperability: Avaya 8500 Communications Manager 2.1 to T1 QSIG with H.323 Application Note Cisco IOS Voice Gateway PBX Interoperability: Avaya 8500 Communications Manager 2.1 to T1 QSIG with H.323 Table of Contents Introduction...1 Network Topology...2 Limitations...2 Hardware

More information

Center for Internet Security Gold Standard Benchmark for Cisco IOS

Center for Internet Security Gold Standard Benchmark for Cisco IOS Center for Internet Security Gold Standard Benchmark for Cisco IOS Level 1 and 2 Benchmarks Version 2.1 http://www.cisecurity.org rat-feedback@cisecurity.org September 2, 2003 Abstract This document defines

More information

Module 6 Configure Remote Access VPN

Module 6 Configure Remote Access VPN Network Security 2 Module 6 Configure Remote Access VPN Learning Objectives 6.1 Introduction to Cisco Easy VPN 6.2 Configure the Easy VPN Server 6.3 Configure Easy VPN Remote for the Cisco VPN Client 4.x

More information

Lab 7.2.9 Load Balancing Across Multiple Paths

Lab 7.2.9 Load Balancing Across Multiple Paths Lab 7.2.9 Load Balancing Across Multiple Paths Objective Configure Load balance across multiple paths. Observe the load balancing process. Background/Preparation Cable a network similar to the one in the

More information

CCNA Security. Chapter Two Securing Network Devices. 2009 Cisco Learning Institute.

CCNA Security. Chapter Two Securing Network Devices. 2009 Cisco Learning Institute. CCNA Security Chapter Two Securing Network Devices 1 The Edge Router What is the edge router? - The last router between the internal network and an untrusted network such as the Internet - Functions as

More information

APNIC Members Training Course Security workshop. 2-4 July, 2008. Port Vila Vanuatu. In conjunction with PACNOG 4

APNIC Members Training Course Security workshop. 2-4 July, 2008. Port Vila Vanuatu. In conjunction with PACNOG 4 APNIC Members Training Course Security workshop 2-4 July, 2008 Port Vila Vanuatu In conjunction with PACNOG 4 Router device security lab 1. APNIC s remote lab In these exercises you will be remotely accessing

More information

Using a Sierra Wireless AirLink Raven X or Raven-E with a Cisco Router Application Note

Using a Sierra Wireless AirLink Raven X or Raven-E with a Cisco Router Application Note Using a Sierra Wireless AirLink Raven X or Raven-E with a Application Note Cisco routers deliver the performance, availability, and reliability required for scaling mission-critical business applications

More information