Universal control module for motorized devices

Size: px

Start display at page:

Download "Universal control module for motorized devices"

Kory Atkinson
8 years ago
Views:

1 Ref: MOD-0105-N The MOD-0105-N is a universal module for motorized devices, blinds, awnings, curtains, doors, etc.. Allows, with vivimat BUS, the local or remote control of a motorized devices, ensuring a reliable use of the motor in both cases. One of its most common uses is to combine the management of various motorized devices, and to control them centrally in a safe way, while the direct access from the individual push buttons of each device is still operational. Technical characteristics Number of motorized devices 1 Power supply 230VAC 50Hz Consumption <0,5W Output type 2 Relies NO de 5A/250VAC connected to phase Maximum engine power 500W Overcurrent and overvoltage protection Via electronic fuses and varistors Temperature range -10ºC / 40ºC Compatible with vivimat III Communication with the vivimat system Through the vivimat BUS LED status indication ID configuration in the BUS via switch Panel installation DIN rail mounting Requires adaptation kit ADP-0010 (NOT INCLUDED)

One of its most common uses is to combine the management of various motorized devices, and to control them centrally in a safe way, while the direct access from the individual push buttons of each

2 Dimensions 42 mm 70 mm 70 mm 70 mm 25 mm 25 mm 44 mm 35 mm * MOD adaptation part ADP-0010 for DIN rail. (NOT INCLUDED) Connections Switches vivimat BUS Manual push down buttons Manual push up buttons Remote push down buttons Remote push up buttons Neutral motor N - Output Output motor down Output motor up Phase N F TT-230 Vac Neuter Earthing - Wiring: All wires of 0,22mm 2

(NOT INCLUDED) Connections Switches vivimat BUS Manual push down buttons Manual push up buttons

3 Configuration Via the switches the MOD-0105-N can define its module address in the vivimat BUS. vivimat III can have up to 50 motorized devices control modules. Select the address of each module as indicated in the configuration made with vivimat Project. The addresses of the modules are consecutively assigned by vivimat Project (There must not be 2 modules of the same type with the same address). ADDRESS 1 ADDRESS 2 ADDRESS 3 ADDRESS 4 ADDRESS 5 ADDRESS 6 ADDRESS 7 ADDRESS 8 ADDRESS 9 ADDRESS 10 ADDRESS 11 ADDRESS 12 ADDRESS 13 ADDRESS 14 ADDRESS 15 ADDRESS 16 ADDRESS 17 ADDRESS 18 ADDRESS 19 ADDRESS 20 ADDRESS 21 ADDRESS 22 ADDRESS 23 ADDRESS 24 ADDRESS 25 ADDRESS 26 ADDRESS 27 ADDRESS 28 ADDRESS 29 ADDRESS 30 ADDRESS 31 ADDRESS 32 ADDRESS 33 ADDRESS 34 ADDRESS 35 ADDRESS 36 ADDRESS 37 ADDRESS 38 ADDRESS 39 ADDRESS 40 ADDRESS 41 ADDRESS 42 ADDRESS 43 ADDRESS 44 ADDRESS 45 ADDRESS 46 ADDRESS 47 ADDRESS 48 ADDRESS 49 ADDRESS 50 The modules MOD-0105-N belonging to a vivimat III system must be registered in the configuration of the installation which is implemented by vivimat Project, assigning an ID number to the module and specifying which motorized devices, the module is going to control.

The addresses of the modules are consecutively assigned by vivimat Project (There must not be 2 modules of the same type with the same address).

4 Functioning LOCAL CTROL : Local control is carried out by on or more buttons connected in parallel (see connections). -A short key press (less than 0,5 sec.) will move totally up or down (motorized device). depending on the push button you have press (up or down) - If the device is moving, a short pressing in the opposite direction will stop the device. - A long key press on the up or down buttons it will move up or down the device depending on the button you have pressed: In the panel you will just see the positions % REMOTE CTROL: The control is carried out by the vivimat home automation system BUS. It is possible to activate the following functions remotely: - Move up or down totally the motorized device. - Move up or down the motorized device to a certain position % - Know the status of the motorized device: % - Configure the module. *SECURITY: The module prioritizes local orders to remote orders. If the module is executing an up or down order in the remote mode, the key press of any local key will stop the motorized devices. LED STATUS INDICATI: 1- Green blinking: Module operative. 2- Red blinking: Module in communication. 3- Red or NOT illuminated: Problems with the module.

- A long key press on the up or down buttons it will move up or down the device depending on the button you have pressed: In the panel you will just see the positions 0-20 - 40-60 - 80-100% REMOTE

5 Installation recommendations - Installation corresponding to a > 100 x 100mm box: The 100 x 100mm box is embedded in the wall of the housing. With 2 screws (NOT INCLUDED) we fix the MOD-0105-N to the box (1). 1 - DIN rail installation: For the DIN rail installation, you require the adaptation kit ADP-0010 (NOT INCLUDED), consisting of 2 pieces, which has to be inserted into the rear of the module (1). Once the pieces are inserted, we fit the module into the DIN rail (2). 1 Adaptation part x 2 3 FT-MOD-0105-N_11/01/10-ENG Product manufactured by: Dinitel 2000 S.A. - Avda. Otaola Eibar ( Guipúzcoa ) Spaint T / F dinitel@dinitel.com

1 - DIN rail installation: For the DIN rail installation, you require the adaptation kit ADP-0010 (NOT INCLUDED), consisting of 2 pieces, which has to be inserted into the rear of

1 light dimming module

1 light dimming module Ref: MOD0400 STAT The MOD0400 is a lighting control module that allows to dimming and monitoring of 1 halogen or incandescent light sources of up to 250W. This lighting circuit can