MX 925 INSTALLING SOFTWARE

Transcription

1 MX 925 INSTALLING SOFTWARE PREPARATION FOR INSTALLATION The minimum OS version for the MX 925 unit is Check the OS version by entering System Mode. 1. Enter System Mode by pressing and holding the 1 key, the 5 key, and the 9 key at the same time. If the system is running when System Mode is accessed, the message System Halt will appear. This is normal and okay. 2. Hold the three keys down for approximately one minute, until the password request window appears. Note: System Mode may also be accessed by using the reset hole on the back of the PIN Pad. 3. The default password for a new unit is This will sometimes be changed to after initial start-up. 4. From Home, choose Information and then Basic System. Scroll down and find Build. This will show the Release Number. If the OS is or above, proceed with install of the MX 925. If the wrong OS is installed, update the OS to the minimum or newer and proceed with installation of the MX 925. Attach the USB memory stick containing the proper files to the dongle required for all PIN Pad installations. Note: The USB memory stick may be inserted into the dongle before or after power-up. 10/05/2015, rev1.1 1

2 INSTALLING SOFTWARE ON THE MX 925 After entering System Mode, choose the Transfer tab. (Sample System Mode screen below.) 1. Ensure that the required files are in the root directory of the USB stick. Best Practices require that only the needed files should be on the USB. 2. From the Transfer section, choose USB-SD Memory. 10/05/2015, rev1.1 2

3 3. A list of available devices will populate. Choose your device (see sample below). 4. Locate the application to install. (See sample below.) 10/05/2015, rev1.1 3

4 5. Select the application. A green checkmark will appear next to it (example in image below). 6. Select Apply (see orange arrow above). The application will install. 10/05/2015, rev1.1 4

5 Once installation is complete, a window will pop up saying Install Successful. 7. Select Okay. 8. If any image packages (.tgz files) are needed, install these now in the same manner as above. 9. Once all files are installed, select Home and then select Reboot (right side of the screen). Note: In some cases, such as Auto-Upgrade, the reboot may automatically occur. It is recommended to always reboot after installing new/updated files. Media files specifically may not be recognized unless a reboot is performed. 10/05/2015, rev1.1 5

6 10. After the reboot, access the App Configuration Main Menu. There will be no indication of keys or any icons, but this menu may be accessed by tapping once (#1) in the right bottom corner of the screen, then once (#2) to the left of that, and then again (#3) in the right bottom corner. (see boxes in image below for location of hidden buttons) Tapping in this sequence will bring up a request for the password. The password will be MX900, or the number Once the password is entered, a scrolling window will appear. Scroll to and choose Network Settings to check the IP Address. 13. Adjust, if needed. Note: The App Config Main Menu will also be accessed to configure the Idle screen, to configure the Read Card screen, and to enable/disable the Show Ads option, as well as RFID Support (turn on/off), Sound and Display/Video Brightness. 14. Once choices are complete, select Apply and then Reboot. Any changes made in the App Config Main Menu will not be active unless Apply is selected and reboot is performed. Note: All the above may also be accessed and adjusted through System Mode. 10/05/2015, rev1.1 6

7 BASIC TROUBLESHOOTING When troubleshooting the MX 925, always verify the OS version first. Also check the installed applications. This will show the applications currently installed and alert to potential missing applications. Additionally, this information will be useful when calling into the Verifone Help Desk for support. To check installed applications, look under the Installed S/W tab. If Debugging is required, the Verifone Help Desk will send one or more files. Download these files and install in the Downloads section. 10/05/2015, rev1.1 7