NW HEALTHCARE SUICIDE-RESISTANT

Transcription

1 NW HEALTHCARE SUICIDE-RESISTANT PRODUCTS CATAL ALOG All rights reserved. No part of this catalog may be reproduced in any form or by any means for commercial purpose, without the prior written permission of Northwest Specialty Hardware Inc.

2 NORTHWEST SUICIDE-RESISTANT PRODUCTS FOR BEHAVIORAL HEALTHCARE Suicide is the eleventh leading cause of death in the United States. Our Nation loses 30,000 lives to this tragedy each year, another 650,000 receive emergency care after attempting to take their own lives (Data from National Strategy for Suicide Prevention). According to the Joint Commission, 1,500 suicides occur in inpatient hospital units annually, and 75 percent of inpatient suicides take place in the bathroom, bedroom, or closet. While not every patient is intent on self-harm, facilities cannot afford both financial and moral risk of leaving open opportunities for suicide or self-harm in the built environment, particularly in patient bathrooms. Northwest Specialty Hardware Inc (Northwest) is dedicated to designing and manufacturing NW suicide-resistant series products, especially washroom accessories, in order to minimize the risk of patient suicide and enhance the security and safety of psychiatric wards, mental health facilities, and correctional facilities. NW washroom accessories meet the suicide-resistant requirements of Section 12 of ADAAG (Americans with Disabilities Act Accessibility Guidelines). Northwest is an organizational member of the U.S. Psychiatric Rehabilitation Association. Northwest is a registered healthcare vendor with VCS (Vendor Credentialing Service). Northwest is a registered vendor with the federal government and various state and county agencies. With our consistent and devoted efforts, Northwest has achieved the high popularity and customer satisfaction in the behavioral healthcare and correctional industry. Northwest has been devoting the great efforts to manufacturing, marketing and distributing NW SecurityBar since NW SecurityBar is the ADA compliant heavy-duty grab bar or handrail for the healthcare and correctional facilities. NW SecurityBar with end caps eliminate ligature attachment points and space for hiding items. NW SecurityBar is listed in the Design Guide of the National Association of Psychiatric Health Systems (NAPHS) and accepted by the New York State Office of Mental Health. NW SecurityBar is a registered trademark of Northwest Specialty Hardware Inc. 1

3 Eliminating Ligature Attachment Points and Space for Hiding Items Outstanding Features Suicide Resistant, No Space Between Wall and Bar End Caps for Anti-Ligature Solution Vertical or Horizontal Installation Custom Lengths or L-Corner Bars Available Self-Draining for Wet Applications Handrail to Allow a Full Grip Suitable for Continuous Handrail Open for Contraband Inspection Variable Fastener Spacing for Easy Retrofits 100% Made in the U.S.A. NW SecurityBar for Correctional and Healthcare Facilities Specially Hardened Aluminum Alloy Clear Anodized Surface, Brush Finishing Look 2

4 NW SecurityBar Description Application: For installation in toilet rooms, shower stalls, at bathtubs, and at other locations required to have NW SecurityBar to provide assistance for persons with disabilities or mobility impairment. The unique design meets the suicide resistant or anti-ligature requirements of ADAAG (Americans with Disabilities Act Accessibility Guidelines). The one piece design resists abuse and does not offer a place to conceal contraband. To facilitate retrofit installations, NW SecurityBar is not pre-drilled for fasteners and offers a continuous mounting surface. This allows adaptation to a variety of mounting conditions where backing, which is critical for proper attachment, may not align with conventional grab bar mounting points. These features make SecurityBar well suited for secure facilities such as Behavioral Health Facilities, Hospitals, Educational Facilities, Airports, Juvenile Detention Facilities, Jails and Prisons, and other public places. Materials: NW SecurityBar is extruded from 6063-T5 aluminum alloy and receive a special treatment providing a clear anodized surface. All edges are radiused and carefully finished. Available Sizes: NW SecurityBar is available from stock in straight lengths of 18", 24", 30", 36",42", 48", 54" and 60". Custom lengths or L-Corner bars are available on special orders. Competitive Advantages: (1) Cost Advantage Northwest is the leading manufacturer of premium detention hardware and accessories. Northwest utilizes our resources and capabilities to create a unsurpassable cost advantage but still maintain the premium quality of SecurityBar Further savings are achieved by taking full advantage of the purchase combination of NW SecurityBar and our entire product line for secure facilities. (2) Manufacturing and Marketing Experience Northwest has been devoting great efforts to manufacturing, marketing and distributing NW SecurityBar since 2003.With our consistent and devoted efforts, Northwest has achieved the high popularity and customer satisfaction in behavioral healthcare and correctional industry. (3 ) Nationwide Delivery Network Northwest has an integrated and nationwide delivery network across North America. Northwest can provide reliable and cost-effective delivery solutions to meet the needs of a wide range of customers and markets. Installation: 1. Determine installation height and location. Locate appropriate backing locations and transfer layout to NW SecurityBar Drill holes 1/32" larger than fastener diameter, 3/4" from bottom of the mounting flange. 2. Before securing bar to wall apply a continuous bead of acrylic latex sealant to back of mounting flange, both top and bottom. Secure to wall and wipe away any excess sealant with a moist cloth. (Note: For security applications epoxy sealant is recommended.) Maintenance: Normal cleaning with a dry cloth or non-acidic detergent is applied to NW SecurityBar maintenance. 3 7/8" To Specify: NW SecurityBar shall be manufactured and distributed by Northwest Specialty Hardware Inc. Special one piece configuration. 1. Material: Extruded 6063-T5 aluminum alloy. 2. Clear anodized surface with brush finish look. 3. Sizes: Reference drawings for lengths and configurations. 4. All exposed edges rounded and finished. 5. End Cap Option: Provide factory installed End Caps. End Caps are recommended for anti-ligature purpose. Self-Draining End Caps are available upon request. 1/4" 3" 11/2" NO FURNISHED BY NORTHWEST SECURITY HEAD FASTENER INTEGRAL MOUNTING FLANGE WALL OR MOUNTING SURFACE 3

5 NW SMALL 1pc SECURITY MIRROR 9 1/2" x 11 1/4" x 1/4" Overall w/8" x 9 3/4" Mirror Surface Material: 18 ga Stainless Steel Sheet Polished to a Mirror Finish Approximating that of Glass 1 pc Mirror Mounting Screws: Security Button Hd,1/4-20 x 3/8" Note: Anchor kit and mirror backplate are available upon request. 4

6 NW SMALL 2pc SECURITY MIRROR 10" x 11 1/2" x 5/16" Frame w/8" x 9 1/2" Mirror Surface Frame: 14 ga Steel w/satin Chrome Finish Mirror Panel: 20 ga Stainless Steel Sheet Polished to a Mirror Finish Approximating that of Glass 2 pc Mirror Mounting Screws: Security Flat Hd,1/4-20 x 1/2" Note: Anchor kit and mirror backplate are available upon request. 5

7 NW LARGE 1pc SECURITY MIRROR 11 1/4" x 17 1/4" x 1/4" Overall, w/ 9 3/4" x 15 3/4" Mirror Surface Material: 18 ga Stainless Steel Sheet Polished to a Mirror Finish Approximating that of Glass 1 pc Mirror Mounting Screws: Security Button Hd, 1/4-20 x 3/8" Note: Anchor kit and mirror backplate are available upon request. 6

8 NW LARGE 2pc SECURITY MIRROR 12 3/8" x 16 3/8" x 5/16" Frame w/10" x 14" Mirror Surface Frame: 14 ga Steel w/satin Chrome Finish Mirror Panel: 20 ga Stainless Steel Sheet Polished to a Mirror Finish Approximating that of Glass 2 pc Mirror Mounting Screws: Security Flat Hd,1/4-20 x 1/2" Note: Anchor kit and mirror backplate are available upon request 7

9 NW MIRROR BACKPLA CKPLATE. Material: Mounting: For use in easy-and-substantial mirror installation or retrofit application. Mild Steel Plate, 3/16"thk Mirror Backplate Sizes with Matching NW 604-1, NW 604-2, NW 605-1, NW Concrete Expansion, Anchor, or Weld On. Red Oxide Primer Note: Discount price for one complete set of the mirror, backplate, and anchor kit. NW MIRROR BACKPLATE NW MIRROR BACKPLATE 8

10 NW 607B CLOTHES HOOK, BOLT-ON 5/8" x 4 5/16" x 3" Projection Material: Stainless Steel Bolt-on, Collapsible US32D Mounting Screws: Security Button Hd, 1/4-20 x 1" 9

11 NW 607W CLOTHES HOOK, WELD-ON Material: Mounting : 5/8" x 3 1/8" x 3" Projection Stainless Steel Weld-on, Collapsible US32D Weld-on 10

12 NW 608 CLOTHES HOOK Material: Mounting Screws: 4" x 4" x 2 1/4" Projection Stainless Steel w/nylon Insert 14 ga Slope Top Housing Front Mounted Collapsible Ball-Joint US32D Security Flat Hd, 1/4-20 x 2" 11

13 NW 608-2S CLOTHES HOOK STRIP, SLOPE TOP Material: Mounting Screws: Features: 6 1/2" x 9 1/2" x 2 1/4" Projection Stainless Steel w/nylon Inserts 14 ga Slope Top Housing Front Mounted Collapsible Ball-Joint US32D Security Flat Hd 1/4-20 x 2" Slope top surface is free from dust and easy-to-clean 12

14 NW 608-3S CLOTHES HOOK STRIP, SLOPE TOP Material: Mounting Screws: Features: 6 1/2" x 14" x 2 1/4" Projection Stainless Steel w/nylon Inserts 14 ga Slope Top Housing Front Mounted Collapsible Ball-Joint US32D Security Flat Hd 1/4-20 x 2" Slope top surface is free from dust and easy-to-clean $

15 NW 608-4S CLOTHES HOOK STRIP, SLOPE TOP Material: Mounting Screws: Features: 6 1/2" x 18" x 2 1/4" Projection Stainless Steel w/nylon Inserts 14 ga Slope Top Housing Front Mounted Collapsible Ball-Joint US32D Security Flat Hd 1/4-20 x 2" Slope top surface is free from dust and easy-to-clean 14

16 NW CLOTHES HOOK STRIP Material: Mounting Screws: 5 1/2" x 18" x 2 1/4" Projection Stainless Steel w/nylon Inserts 14 ga Flat Top Housing Front Mounted Collapsible Ball-Joint US32D Security Flat Hd 1/4-20 x 2" $

17 NW 611 BALL TIP, TOILET PAPER HOLDER 4" x 4" x 4" Projection Material: Stainless Steel w/nylon Insert 14 ga Slope Top Housing Front Mounted Collapsible Ball-Joint Ball Tip Lver US32D Mounting Screws: Security Flat Hd, 1/4-20 x 2" Features: For holding toilet paper Anti-Ligature Design conveniently and easily surface-mounted on wall Note: NW 611 with Flat Tip Lever also Available NW 611, Ball Tip NW 611, Flat Tip 16

18 NW 618 ANTI-LIGATURE TURE SHELF 18" x 8" x 5 1/2" Projection Material: 14 ga Stainless Steel Front Mounted US32D Finish Outside, Satin Finish Inside Features: Fully Welded Single Piece Construction Front Edge Folded under and Welded 1 inch All Edges Ground Smooth for Anti-Ligature Mounting Screws: Security Button Head, 1/4-20 x 1 1/2" $48.00 Option: Optional for Installation over NW608-4 Flat Top Hook Strips to Offer the Unique Cost-Effective Combination for the Shelf and Clothes Hook Strips. 17

19 NW 619 ANTI-LIGATURE TURE RECESSED SHELF 18" x 7" x 4" Material: 16 ga Stainless Steel Chase Mounted Brush Finish Frame Satin Finish Interior Features: Fully Welded Construction All Edges Ground Smooth Installation: Install in Wall Opening Back of Shelf Has Welded Anchor Nuts to Receive Threaded Studs (Provided) $

20 NW 620 RECESSED TOILET TISSUE HOLDER Overall Internal Material: Features: Installation: 6 1/4" dia. x 4 3/4" depth 5 1/2" dia. x 4 5/16" depth 16 ga Stainless Steel Chase Mounted Exposed Surfaces in Satin Finish Forged one-piece seamless construction Rim of holder beveled to insure tight fit to wall surface $26.90 Back of holder has welded anchor nuts to receive threaded studs. 11 gauge die-formed galvanized steel back plate, reversible for shallow or deep wall installation. 19

21 NW 621 RECESSED TOILET TISSUE HOLDER Overall 7" x 7" x 4 1/2" depth Internal 5 3/8" dia. x 3 15/16" depth Material: 14 ga Stainless Steel Flange 16 ga Stainless Steel Holder Front Mounted Exposed Surfaces in Satin Finish Screws: Security Button Head, 1/4"-20 x 1" for installation to wall anchors (Not included) Features: Flange welded to holder to ensure a tight fit to wall surface Holder forged one-piece seamless construction Requirement: It is required to use a security caulk around the front edge between the flange and the holder for anti-ligature purpose. $

22 NW 622 RECESSED SOAP DISH Overall Internal Material: Features: Installation: 7" x 5" x 3" depth 5 5/8" x 3 5/8" x 2 3/4" depth 18 ga Stainless Steel Chase Mounted Satin Finish or Brush Finish Forged one-piece seamless construction Rim of soap dish beveled to insure tight fit to wall surface $22.50 Back of dish has welded anchor nuts to receive threaded studs. 11 gauge die-formed galvanized steel back plate, reversible for shallow or deep wall installation. 21

23 NW 624 FRONT MOUNTED SOAP DISH 5" x 2 1/4" x 2 13/16" Projection Material: 7 ga Stainless Steel Front Mounted Brush Finish Screws: Security Flat Head, 1/4"-20 x 1 1/2" for installation to wall anchors (Not included) Features: Formed from single piece of stainless steel with three drain holes $17.50 Warning: NW 624 Soap Dish is not the anti-ligature product and should not be installed in areas where there is concern for any type of bodily harm. 22

24 NW 691 ANTI-LIGATURE TURE FOOD PASS NW 691 Anti-Ligature Food Pass w/ Lock Prep is designed and manufactured based on the client feedback and requirements for challenging Mental Healthcare environments. NW 691 Anti-Ligature Food Pass is 100% made in the U.S.A.. Material: Frame Opening: Hinges: Features: Welded Steel Assembly, 10 ga Frame with 3/16" Door Food Pass or Cuff Port Kits 15" H x 21" W 6" H x 15" W 3" Hinge with 90 Degree Stop USP (Prime Painted) Fully Adjustable to fit 1 3/4" or 2" Door Applications Specially Designed for Anti-Ligature Purpose Rounded Edges Inside and Outside Hinges with Rounded Corners All Welds Ground Smooth Dome Lock Cover Aluminum Handle Cover NW 691 FOOD PASS W/ LOCK PREP 23