User's Guide Ergotron LX

Transcription

1 User's Guide Ergotron LX Wall Mount USA Europe x A B C D mm #8-32 M4 x 10mm M4 x 10mm 3/32" 3 1/8" 2.5mm For optimum ergonomic viewing, set top of monitor screen 1 below eye height of operator. 4mm 1 of 8

2 1 Determine Ergonomic Mounting Height (for wall mounted applications) Monitor Size 15" 16" 18.1" 20" 21" 22" Mounting Heights Screen Aspect Ratios 4 x 3 16 x 9 Sitting Standing Sitting Standing 34.8" (883 mm) 34.5" (875 mm) 33.8" (859 mm) 33.3" (845 mm) 33" (837 mm) 32.7" (829 mm) 50.8" (1289 mm) 50.5" (1281 mm) 49.8" (1265 mm) 49.3" (1251 mm) 49" (1243 mm) 48.7" (1236 mm) 35.6" (904 mm) 35.3" (897 mm) 34.8" (884 mm) 34.4" (872 mm) 34.1" (866mm) 33.9" (860 mm) 51.6" (1310 mm) 51.3" (1304 mm) 50.8" (1291 mm) 50.45" (1279 mm) 50.1" (1273 mm) 49.9" (1266 mm) These mounting heights assume your monitor mounting holes are located in the center, relative to the monitor screen. If your monitor's mounting holes are located off center (vertically), you can adjust your mounting height accordingly. ie. (Back of Monitor) Subtract 1" (25 mm) from the Mounting Height. Add 1" (25 mm) from the Mounting Height. For configurations without extension, add 3.5" (89 mm) to the mounting height from the table above. 2 of 8

3 x 5/8" when attaching to Pole Clamps, use x 5/8" screws, Do NOT use screws 1/8"! WARNING Because surfaces vary widely and the ultimate mounting method is out of Ergotron s control, it is imperative that you consult with appropriate engineering, architectural or construction professional to ensure that your Ergotron mounting solution is mounted properly to handle applied loads " (28.6mm) 4.1" (104mm) 3 of 8

4 3! If your monitor uses a screw size other than M4 x 10mm, DO NOT use the M4 x 10mm screws or knob provided as they could result in damage to the monitor. #8-32 M10mm M10mm a 3/32" b M10mm M10mm 4 of 8

5 4 With Extension Without Extension 5 Leave enough slack in cable to pivot arm and monitor 5 of 8

6 6 Range of Motion The Ergotron LX Monitor Arm is designed to adjust quickly and easily according to your needs - refer to following steps for adjustment and page 8 for Ergonomic Ground Rules. Lift - Up & Down Tilt - Back & Forth Pan/Arm Swing - Side-to-side 75 Rotate - P/L (Portrait/Landscape) ±50 up to " (330 mm) 5 7 Lift Motion Move monitor up and down through entire range of motion. If it does not stay in place at any point it will need adjustment - see below. Adjust so upward and downward moving forces are equal. Once this is achieved turn adjustment screw 2-4 turns clockwise to give slight upward bias to lift system. 13" (330 mm) ±50 Adjust Lift To Increase Lifting Force: Turn screw clockwise. To Decrease Lifting Force: Turn screw counterclockwise. 4mm! CAUTION DO NOT overtighten fasteners. Overtightening may cause damage to your equipment. 6 of 8

7 8 Tilt Motion Tilt monitor back and forth through entire pivot range of motion. If it does not stay in place or movement in one direction is stiff, pivot needs adjustment - see below. Adjust until monitor 75 stays in place and tilting forces, up or down, are equal. Adjust Tilt To Increase Tilt Lifting Force: Turn screw clockwise. To Decrease Tilt Lifting Force: Turn screw counterclockwise. 5! CAUTION Never remove this adjustment screw! Removing adjustment screw will cause damage to the arm and possible damage to equipment. 9 Arm Swing Swing arms from side-to-side at both pivot points through entire range of motion. If it does not stay in place or movement in one direction is stiff, tension needs adjustment - see below. Adjust until arms stay in place and tension, side-to-side, is equal. Adjust Arm Swing 2.5mm To Increase Tension: Turn screw clockwise. To Decrease Tension: Turn screw counterclockwise. 7 of 8

8 ? Troubleshooting Lift - Up & Down Tilt - Back & Forth 75 Arm Swing - Side-to-side ±50 13" (330 mm) 5 Symptom Probable Cause Solution Monitor lifts up and down too easily or with difficulty. Lifting force needs adjustment. Monitor exceeds weight capacity*. 7 Lift Motion 6 USA Europe Monitor tilts back and forth too easily or with difficulty. Tilt lifting force needs adjustment. 8 Tilt Motion 7 Arm swings from side-to-side too easily or with difficulty. Side-to-side tension needs adustment. 9 Arm Swing 7 *Weight Capacity: 5-20 lbs. ( kg). Warranty 2005 Ergotron, Inc. All rights reserved. Patents Pending and Patented U.S. & Foreign. Ergotron is a registered trademark of Ergotron, Inc. Reproduction of this material in whole or part for any purpose other than that authorized by Ergotron, Inc. is prohibited. 8 of 8