PRODUCT CONTROL SECTION
|
|
|
- Daniel Flowers
- 7 years ago
- Views:
Transcription
1 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida BOARD AND CODE ADMINISTRATION DIVISION T (786) F (786) NOTICE OF ACCEPTANCE (NOA) CertainTeed Corporation 18 Moores Road Malvern, PA SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: CertainTeed Modified Bitumen System over Lightweight Concrete Decks. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA No and consists of pages 1 through 34. The submitted documentation was reviewed by Alex Tigera. Page 1 of 34
2 ROOFING SYSTEM APPROVAL Category: Sub-Category: Material: Deck Type: Roofing Modified Bitumen APP/SBS Lightweight Concrete psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product All Weather/Empire Base Sheet Flexiglas Base Sheet Flintlastic Base 20 Dimensions 39 3 / 8" x ; Roll weight: 70 lbs. (2 squares) 39 3 / 8" x 98 9 ; Roll weight: 90 lbs. (3 squares) 39 3 / 8" x 49 6 ; Roll weight: 90 lbs. (1.5 squares) Test Specification ASTM D 4601, Type II UL G2 ASTM D 4601, Type II UL Type G2 ASTM D 6163, Grade S, Type I Flintlastic Ultra Glass SA 39 3 / 8 x ASTM D 6163, Type I Product Description Asphalt coated, fiberglass reinforced base sheet. Modified Bitumen coated fiberglass base sheet. Modified Bitumen coated fiberglass base sheet. Self-adhering, fiberglass reinforced, SBS modified bitumen base/ply sheet. Black Diamond Base Sheet 39 3 / 8 x 68 7 ASTM D 1970 Self-adhering, fiberglass reinforced, SBS modified bitumen base/ply sheet. Flintglas Ply Sheet Type IV Flintglas Premium Ply Sheet Type VI Flintlastic STA Flintlastic GTA Flintlastic GTA-FR 39 3 / 8" x ; Roll weight: 38 lbs. (5 squares) 39 3 / 8" x ; Roll weight: 40 lbs. (5 squares) 39 3 / 8" x ; Roll weight: 87 lbs / 8" x ; Roll weight: 105 lbs / 8" x 32 10"; Roll weight: 105 lbs. ASTM D 2178, Type IV UL Type G1 ASTM D 2178, Type VI UL Type G1 ASTM D 6222, Grade S, Type I ASTM D 6222, Grade G, Type I ASTM D 6222, Grade G, Type I Fiberglass, asphalt impregnated ply sheet. Fiberglass, asphalt impregnated ply sheet. Smooth surfaced APP Modified Bitumen membrane with non-woven polyester mat reinforcement for torch application. Granule surfaced APP Modified Bitumen membrane with non-woven polyester mat reinforcement for torch application. Granule surfaced APP Modified Bitumen membrane with non-woven polyester mat reinforcement for torch application. Page 2 of 34
3 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Flintlastic GMS Flintlastic Premium GMS Flintlastic FR-P Flintlastic Premium FR-P Flintlastic FR Dual Cap Flintlastic FR Cap 30 Flintlastic FR Cap 30 T Flintlastic Base 20 T Flintlastic FR Cap 30 CoolStar Dimensions 39 3 / 8" x ; Roll weight: 94 lbs / 8" x ; Roll weight: 101 lbs / 8" x ; Roll weight: 101 lbs / 8" x ; Roll weight: 101 lbs / 8" x 32' 10"; Roll weight: 103 lbs / 8" x ; Roll weight: 86 lbs / 8 x ; Roll weight: 100 lbs / 8 x 33 ; Roll Weight: 81lbs / 8" x ; Roll weight: 88 lbs. Test Specification ASTM D 6164, Grade G, Type I ASTM D 6164, Grade G, Type II ASTM D 6164, Grade G, Type I ASTM D 6164, Grade G, Type II ASTM D 6162, Grade G, Type I ASTM D 6163, Grade G, Type I ASTM D 6163, Grade G, Type I ASTM D 6163, Grade S, Type I ASTM D 6163, Grade G, Type I Product Description Granule surfaced SBS Modified Bitumen membrane with non-woven polyester mat reinforcement for mop application. Granule surfaced SBS Modified Bitumen membrane with non-woven polyester mat reinforcement for mop application. Fire resistant, granule surfaced SBS Modified Bitumen Membrane with non-woven polyester mat reinforcement for mop application. Fire resistant, granule surfaced SBS Modified Bitumen Membrane with non-woven polyester mat reinforcement for mop application. Granule surfaced SBS modified bitumen membrane with a nonwoven polyester/fiberglass composite mat reinforcement for use in cold or mop applications. Fire resistant, granule surfaced SBS Modified Bitumen membrane with fiberglass mat reinforcement for mop applications. Granule surfaced SBS Modified Bitumen membrane with fiberglass mat reinforcement for torch application. Modified Bitumen, coated fiberglass base sheet for torch application. Fire resistant, granule surfaced SBS Modified Bitumen membrane with fiberglass mat reinforcement for mop applications. Covered with reflective CoolStar Coating. Page 3 of 34
4 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Flintlastic FR Cap 30 T CoolStar Flintlastic GTA CoolStar Flintlastic GTA-FR CoolStar Flintlastic GMS CoolStar Flintlastic Premium GMS CoolStar Flintlastic FR-P CoolStar Flintlastic Premium FR-P CoolStar Flintlastic Ultra Poly SMS Base Sheet Dimensions 39 3 / 8" x ; Roll weight: 102 lbs / 8" x ; Roll weight: 106 lbs / 8" x ; Roll weight: 106 lbs / 8" x ; Roll weight: 97 lbs / 8" x ; Roll weight: 103 lbs / 8" x ; Roll weight: 103 lbs / 8" x ; Roll weight: 103 lbs / 8" x ; Roll weight: 90 lbs. Test Specification ASTM D 6163, Grade G, Type I ASTM D 6222, Grade G, Type I ASTM D 6222, Grade G, Type I ASTM D 6164, Grade G, Type I ASTM D 6164, Grade G, Type II ASTM D 6164, Grade G, Type I ASTM D 6164, Grade G, Type II ASTM D 6164, Grade S, Type I Product Description Fire resistant, granule surfaced SBS Modified Bitumen membrane with fiberglass mat reinforcement for mop applications. Covered with reflective CoolStar Coating. Granule surfaced APP Modified Bitumen membrane with non-woven polyester mat reinforcement for torch application. Covered with reflective CoolStar Coating. Granule surfaced APP Modified Bitumen membrane with non-woven polyester mat reinforcement for torch application. Covered with reflective CoolStar Coating. Granule surfaced SBS Modified Bitumen membrane with non-woven polyester mat reinforcement for mop application. Covered with reflective CoolStar Coating. Granule surfaced SBS Modified Bitumen membrane with non-woven polyester mat reinforcement for mop application. Covered with reflective CoolStar Coating. Fire resistant, granule surfaced SBS Modified Bitumen Membrane with non-woven polyester mat reinforcement for mop application. Covered with reflective CoolStar Coating. Fire resistant, granule surfaced SBS Modified Bitumen Membrane with non-woven polyester mat reinforcement for mop application. Covered with reflective CoolStar Coating. Smooth surfaced SBS Modified Bitumen Membrane with non-woven polyester mat reinforcement for mop applications. Page 4 of 34
5 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Glasbase Base Sheet Dimensions 39 3 / 8" x 98 9 ; Roll weight: 75 lbs. (3 squares) Test Specification ASTM D 4601, Type II UL Type G2 Product Description Asphalt coated, fiberglass base sheet. Flintlastic Poly SMS Base Sheet Yosemite Venting Base Sheet Flintlastic APP Base T 39 3 / 8" x 64' 3"; Roll weight: 90 lbs. (2 squares) 39 3 / 8" x ; Roll weight: 85 lbs / 8 x 65 4 ; Roll weight: 100 lbs. (2 squares) ASTM D 4601, Grade S, Type II UL Type G2 ASTM D 3909 ASTM D 4897, Type II UL G3 ASTM D6509 Modified Bitumen coated polyester base sheet. Mineral Surfaced fiberglass reinforced buffer sheet. Modified Bitumen coated fiberglass base sheet. APPROVED INSULATIONS: TABLE 2 Product Name Product Description Manufacturer (With Current NOA) FlintBoard ISO Polyisocyanurate foam insulation CertainTeed Corp. FlintBoard H ISO, FlintBoard H ISO Cold Polyisocyanurate foam insulation CertainTeed Corp. ACFoam-II, ACFoam-IV Polyisocyanurate foam insulation Atlas Roofing Corp. High Density Wood Fiberboard Wood fiber insulation board Generic Perlite Insulation Perlite insulation board Generic DensDeck, DensDeck Prime Water resistant gypsum board Georgia Pacific Gypsum LLC H-Shield, H-Shield CG Polyisocyanurate foam insulation Hunter Panels LLC ENRGY 3, ENRGY 3 25 PSI Polyisocyanurate foam insulation Johns Manville Corp. Multi-Max FA-3 Polyisocyanurate roof insulation RMax Operating, LCC Insulfoam EPS Expanded Polystyrene Insulfoam, a Div. of Carlisle Const. Materials Page 5 of 34
6 APPROVED FASTENERS: Fastener Number Product Name TABLE 3 Product Description 1. FM-90 Base ply fastening systems for lightweight concrete decks. Dimensions Manufacturer (With Current NOA) 2.7 x 1.7 Altenloh, Brinck & Co. U.S., Inc. 2. CR Assembled Base Sheet Fastener (1.2 ) and CR Assembled Base Sheet Fastener (1.7 ) Fastener assembly for Base Sheet fastening only x Galvalume steel stress plate and x Galvalume steel stress plate OMG, Inc. 3. Twin Loc-Nails Galvanized stress plate and tube with integrated locking staple 2.7 round x various lengths Altenloh, Brinck & Co. U.S., Inc. APPROVED SURFACING/COATING OPTIONS: TABLE 4 Chosen components must be applied according to manufacturer s application instructions. Any coating, listed below, used as a surfacing, must be listed within a current NOA. System Number Manufacturer Application 1. Generic Gravel applied at 400 lbs/sq., adhered with flood coat of asphalt at 60 lbs/sq. 2. Generic Slag applied at 300 lbs/sq., adhered with flood coat of asphalt at 60 lbs/sq. 3. Karnak Corp. Karnak (#97 AF) Fibrated Aluminum Roof Coating applied at an application rate of 1.5 gal/sq. 4. CertainTeed Corp. FlintCoat A-150 applied at an application rate of 1.5 gal/sq. 5. Gardner Asphalt Corp. APOC #212 Fibered Aluminum Roof Coating applied at an application rate of 1.5 gal/sq. 6. Gardner Asphalt Corp. APOC #400 Sunbrite applied at an application rate of 3 gal./sq. Page 6 of 34
7 EVIDENCE SUBMITTED: Test Agency/Identifier Name Report Date Factory Mutual Research Corp. FM D3A3.AM 04/04/97 FM D0A0.AM 12/23/98 FM D7A4.AM 11/09/98 FM /19/13 FM /15/10 Underwriters Laboratories, Inc. UL 790 R /11/13 United States Testing Company ASTM D /03/88 ASTM D R 12/02/87 Momentum Technologies, Inc. ASTM D 4601 AX31G8D 09/05/08 ASTM D6164 AX31G8F 06/05/09 ASTM D6222 AX31G8G 06/05/09 ASTM D 3909/ D 4897 AX31G8C 09/05/08 Trinity ERD TAS 114(J) /05/01 TAS 117 (B) /10/06 TAS 117 (B) O R1 06/27/07 TAS 114 (H) Letter 04/05/06 TAS /06/06 TAS /29/04 TAS 117 (B)/ ASTM D 6862 C8500SC /30/07 TAS 114 C /19/08 ASTM Physical Properties C R4 03/25/10 ASTM D6164/D4798 C /10/11 ASTM D4601 C /28/12 ASTM D1970 C /28/12 ASTM D5147/D4798 C R1 11/01/12 ASTM D5147/D4798 C R1 11/01/12 TAS 117 B C /09/11 FM 4470/TAS 114 C /22/10 TAS 117 & TAS 114 C /18/10 TAS 117 & TAS 114 C /10/10 FM 4470/TAS 114 C /26/12 ASTM D1876 C R1 05/20/15 ASTM D1876, TAS 114 (H), C /13/12 TAS 117 (B) ASTM D1876, TAS 114 (H), C /26/14 FM 4474 ASTM D4798 C A-R1 02/21/13 ASTM D4798 C /05/13 ASTM D6222 C R1 12/31/13 PRI Construction Materials ASTM D6163 CTC /22/08 Technologies LLC ASTM D6163 CTC /09/11 Page 7 of 34
8 EVIDENCE SUBMITTED: Test Agency/Identifier Name Report Date ASTM D6222 CTC /09/11 ASTM D6164/D4798 CTC /09/11 ASTM D2178 CTC /13/12 ASTM D2178 CTC /13/12 ASTM D4601 CTC /13/12 ASTM D6509 CTC /04/12 ASTM D6163 CTC /11/12 ASTM D6163 CTC /11/12 ASTM D6164 CTC /11/12 ASTM D6164 CTC /09/13 ASTM D6164 CTC /09/13 ASTM D6162 CTC /02/13 ASTM D6164 CTC /02/13 Page 8 of 34
9 APPROVED ASSEMBLIES Membrane Type: Deck Type 4I: Deck Description: System Type A(1): APP Modified Lightweight Concrete, Insulated Concrecel Cellular Lightweight Concrete, min 400 psi Anchor sheet mechanically fastened, one or more layer of insulation adhered with approved asphalt. Structural concrete or Ga. ASTM A653, Grade SS80 steel deck shall be secured 6 o.c. to structural supports spaced a maximum of 5 ft on center with 5 / 8 puddle welds. Steel deck side laps are attached 12 o.c.with Traxx/1 fasteners. Followed by Concrecel Bonding agent applied to the deck at rate 1200 sq. ft/gal using a compressed air sprayer. Rigid insulation panels shall be placed in a minimum ¼ slurry-coat of insulating concrete and allowed to the cure overnight. The following day the rigid insulation shall be covered with a minimum 2 ¼ topcoat cast of Concrecel. After an additional cure time of 24 hours, Concrecel curing compound was a roller applied at a rate of 300sq. ft/gal. Anchor Sheet: Fastening: One ply or more plies of Glasbase Base Sheet, All Weather/Empire Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20 or Flintlastic Poly SMS Base Sheet fastened to the deck as described below: Fasten base sheet to deck with OMG CR Assembled Base Sheet Fasteners spaced at 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 ACFoam-II, FlintBoard ISO, ENRGY 3, ENRGY 3 25 PSI, H-Shield, FlintBoard H ISO Minimum 1.5 thick N/A N/A Approved High Density Wood Fiberboard Minimum ½ thick N/A N/A Approved Perlite Insulation Minimum ¾ thick N/A N/A DensDeck, DensDeck Prime Minimum ¼ thick N/A N/A Page 9 of 34
10 Top Insulation Layer Any Insulation listed for Base Layer, above. Insulation Fasteners (Table 3) N/A Fastener Density/ft 2 N/A Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of lbs/100 ft 2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Ply Sheet: Membrane: Surfacing: One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered or one ply of Flintlastic STA or Flintlastic APP Base T torch adhered. Flintlastic GTA, Flintlastic GTA CoolStar, Flintlastic GTA-FR or Flintlastic GTA-FR CoolStar torch adhered to base or ply sheet. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 10 of 34
11 Membrane Type: Deck Type 4I: Deck Description: System Type A(2): SBS Modified Lightweight Concrete, Insulated Concrecel Cellular Lightweight Concrete, min 400 psi Anchor sheet mechanically fastened, one or more layer of insulation adhered with approved asphalt. Structural concrete or ga. ASTM A653, Grade SS80 steel deck shall be secured 6 o.c. to structural supports spaced a maximum of 5 ft on center with 5/8 puddle welds. Steel deck side laps are attached 12 o.c.with Traxx/1 fasteners. Followed by Concrecel Bonding agent applied to the deck at rate 1200 sq. ft/gal using a compressed air sprayer. Rigid insulation panels shall be placed in a minimum ¼ slurry-coat of insulating concrete and allowed to the cure overnight. The following day the rigid insulation shall be covered with a minimum 2 ¼ topcoat cast of Concrecel. After an additional cure time of 24 hours, Concrecel curing compound was a roller applied at a rate of 300sq. ft/gal. Anchor Sheet: Fastening: One or more plies of All Weather/Empire Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20 or Flintlastic Poly SMS Base Sheet fastened to the deck as described below: Fasten base sheet to deck with OMG CR Assembled Base Sheet Fasteners spaced at 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 ACFoam-II, FlintBoard ISO, ENRGY 3, ENRGY 3 25 PSI, H-Shield, FlintBoard H ISO Minimum 1.5 thick N/A N/A Approved High Density Wood Fiberboard Minimum ½ thick N/A N/A Approved Perlite Insulation Minimum ¾ thick N/A N/A DensDeck, DensDeck Prime Minimum ¼ thick N/A N/A Page 11 of 34
12 Top Insulation Layer Any Insulation listed for Base Layer, above. Insulation Fasteners (Table 3) Fastener Density/ft 2 Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of lbs/100 ft 2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. N/A N/A Ply Sheet: Membrane: Surfacing: One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheetm Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. or one ply of Flintlastic Ultra Poly SMS Base Sheet torch applied or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered. One or more plies of Flintlastic GMS, Flintlastic GMS CoolStar, Flintlastic Premium GMS, Flintlastic Premium GMS CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR- P CoolStar, Flintlastic Premium FR-P, Flintlastic Premium FR-P CoolStar, Flintlastic FR Cap 30, Flintlastic FR Cap 30 CoolStar adhered to ply sheet with approved mopping asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR Cap 30 T or Flintlastic FR Cap 30 T CoolStar torch adhered to ply sheet. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 12 of 34
13 Membrane Type: Deck Type 4I: Deck Description: System Type A(3): APP Modified Lightweight Concrete, Insulated Min. 200 psi. Mearlcrete or min. 160 psi Elastizel Cellular Lightweight Concrete Anchor sheet mechanically fastened, one or more layer of insulation adhered with approved asphalt. Structural concrete or min. 22 ga., grade C (33ksi), type BW slotted steel deck attached to steel supports spaced at a maximum 5 ft. o.c. with 5/8 puddle welds or with 3/8 welding washers spaced maximum 6 o.c. (at each flute). Steel deck side laps are attached 18 o.c.with Traxx/1 fasteners or #10 self-tapping screws. Mearlcrete cast at 40 pcf wet density or Range II Elastizel is applied with an 1/8 slurry coat followed by optional min. 2 thick Star-R-Foam Gripper EPS board or min. 1 thick Apache Corrugated Holey Board or Mearl Corrugated EPS Insulation. A min. 2 thick cap of Mearlcrete or Elastizel is placed over the insulations. Anchor Sheet: One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet or Yosemite Venting Base Sheet* mechanically attached to the deck using OMG CR Assembled Base Sheet Fastener, or FM-90 Fasteners spaced 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. *Only with FM-90 One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 ACFoam-II, FlintBoard ISO, ENRGY 3, ENRGY 3 25 PSI, H-Shield, FlintBoard H ISO Minimum 1.5 thick N/A N/A Approved High Density Wood Fiberboard Minimum ½ thick N/A N/A Approved Perlite Insulation Minimum ¾ thick N/A N/A DensDeck, DensDeck Prime Minimum ¼ thick N/A N/A Page 13 of 34
14 Top Insulation Layer Any Insulation listed for Base Layer, above. Insulation Fasteners (Table 3) Fastener Density/ft 2 Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of lbs/100 ft 2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. N/A N/A Ply Sheet: Membrane: Surfacing: One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered or one ply of Flintlastic STA or Flintlastic APP Base T torch adhered. Flintlastic GTA, Flintlastic GTA CoolStar, Flintlastic GTA-FR or Flintlastic GTA-FR CoolStar torch adhered to base or ply sheet. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 14 of 34
15 Membrane Type: Deck Type 4I: Deck Description: System Type A(4): SBS Modified Lightweight Concrete, Insulated Min. 200 psi. Mearlcrete or min. 160 psi Elastizel Cellular Lightweight Concrete Anchor sheet mechanically fastened, one or more layer of insulation adhered with approved asphalt. Structural concrete or min. 22 ga., grade C (33ksi) type BW slotted steel deck attached to steel supports spaced at a maximum 5 ft. o.c. with 5/8 puddle welds or with 3/8 welding washers spaced maximum 6 o.c. (at each flute). Steel deck side laps are attached 18 o.c.with Traxx/1 fasteners or #10 self-tapping screws. Mearlcrete cast at 40 pcf wet density or Range II Elastizel is applied with an 1/8 slurry coat followed by optional min. 2 thick Star-R-Foam Gripper EPS board or min. 1 thick Apache Corrugated Holey Board or Mearl Corrugated EPS Insulation. A min. 2 thick cap of Mearlcrete or Elastizel is placed over the insulation. Anchor Sheet: One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet or Yosemite Venting Base Sheet* mechanically attached to the deck using OMG CR Assembled Base Sheet Fastener, or FM-90 Fasteners spaced 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. *Only with FM-90 One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 ACFoam-II, FlintBoard ISO, ENRGY 3, ENRGY 3 25 PSI, H-Shield, FlintBoard H ISO Minimum 1.5 thick N/A N/A Approved High Density Wood Fiberboard Minimum ½ thick N/A N/A Approved Perlite Insulation Minimum ¾ thick N/A N/A DensDeck, DensDeck Prime Minimum ¼ thick N/A N/A Page 15 of 34
16 Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 Any Insulation listed for Base Layer, above. Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of lbs/100 ft 2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. N/A N/A Ply Sheet: Membrane: Surfacing: One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. or one ply of Flintlastic Ultra Poly SMS Base Sheet torch applied or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered. One or more plies of Flintlastic GMS, Flintlastic GMS CoolStar, Flintlastic Premium GMS, Flintlastic Premium GMS CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR- P CoolStar, Flintlastic FR Cap 30, Flintlastic FR Cap 30 CoolStar adhered to ply sheet with approved mopping asphalt applied within the EVT range and at a rate of lbs/sq. or Flintlastic FR Cap 30 T or Flintlastic FR Cap 30 T CoolStar torch adhered to ply sheet. Any of the approved surfacing/coating options listed in Table 4.s psf (See General Limitation #7) Page 16 of 34
17 Membrane Type: Deck Type 4I: Deck Description: System Type A(5): SBS Modified Lightweight Concrete, Insulated Elastizel Cellular Lightweight Concrete, min 350 psi Anchor sheet mechanically fastened, one or more layer of insulation adhered with approved asphalt. min. 22ga., Grade 33, Type B vented steel deck attached to steel supports spaced maximum 5ft. o.c. with Tek/5 screws spaced 6 o.c.. Steel deck side laps are attached 20 o.c. with Tek/1 screws. Elastizell with Zell-Fibers (47-50 pcf wet cast density) is applied with an 1/8 slurry coat followed by min. 1 thick EPS holey board and a min. 2 thick top coat. Anchor Sheet: One or more plies of Yosemite Venting Base Sheet mechanically attached to the deck using FM-90 fasteners spaced 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 ACFoam-IV Minimum 1.5 thick N/A N/A Note: All insulation joints shall be staggered and adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of 25 lbs/100 ft 2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Ply Sheet: One or more plies of Yosemite Venting Base Sheet spot-mopped with 9-inch diameter spots of ASTM D312, Type IV hot asphalt spaced in an 18 x 18-inch grid or strip-mopped with 9- inch wide ribbons of ASTM D312, Type IV hot asphalt spaced 18-inch o.c. One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of 25 lbs./sq. Page 17 of 34
18 Membrane: Surfacing: One ply of Flintlastic FR Cap 30, Flintlastic FR Cap 30 CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR-P CoolStar, Flintlastic Premium FR-P or Flintlastic Premium FR-P CoolStar adhered with approved mopping asphalt applied within the EVT range and at a rate of 25 lbs./sq. or one ply of Flintlastic FR Cap 30 T or Flintlastic FR Cap 30 T CoolStar, torch-applied to ply sheet. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 18 of 34
19 Membrane Type: Deck Type 4I: Deck Description: System Type A(6): SBS Modified Lightweight Concrete, Insulated Elastizell Cellular Lightweight Concrete, min 390 psi One or more layer of insulation adhered with approved adhesive. Membrane fully adhered. min. 22ga., Grade 33, Type B vented steel deck attached to steel supports spaced maximum 5ft. o.c. with Tek/5 screws spaced 6 o.c. Steel deck side laps are attached 20 o.c. with Tek/1 screws. Elastizell with Zell-Fibers is applied with an 1/8 slurry coat followed by min. 1 thick EPS holey board and a min. 2 thick top coat. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 H-Shield CG, FlintBoard H ISO Cold Minimum 1.5 thick N/A N/A Note: Insulation shall be adhered to the deck with OMG OlyBond 500 adhesive in ¾ wide ribbons spaced 6- inch o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Ply Sheet: Membrane: Surfacing: One or more plies of Glasbase Base Sheet, All Weather/Empire Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet adhered with Millennium Hurricane Force Membrane Adhesive applied in ½ ¾ wide ribbons spaced 6-inch o.c. None One or more plies of Flintlastic FR Cap 30, Flintlastic FR Cap 30 CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR-P CoolStar, Flintlastic Premium FR-P or Flintlastic Premium FR-P CoolStar adhered to base sheet with Millennium Hurricane Force Membrane Adhesive applied in ½ ¾ wide ribbons spaced 6-inch o.c. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 19 of 34
20 Membrane Type: Deck Type 4I: Deck Description: System Type A(7): SBS Modified Lightweight Concrete, Insulated Minimum 350 psi Cellular Lightweight Concrete over steel deck; with a minimum pull out value (withdrawl resistance) of 128 lbf. when tested with 1.8-inch Twin Loc-Nails. Anchor sheet mechanically fastened, one or more layer of insulation adhered with approved asphalt. min. 22ga., Grade 33, Type B vented steel deck attached to steel supports spaced maximum 5ft. o.c.with Tek/5 screws spaced 6 o.c. Steel deck side laps are attached 20 o.c. with Tek/1 screws. A minimum 1/8 slurry coat followed by min. 1 thick EPS holey board and a min. 2 thick top coat. Anchor Sheet: One or more plies of Yosemite Venting Base Sheet, Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet mechanically attached to the deck using Twin Loc- Nails spaced 9 o.c. in the 4 side lap and 9 o.c. in two evenly divided, staggered rows in the center of the sheet. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 ACFoam-II, FlintBoard ISO, ACFoam-IV Minimum 1.5 thick N/A N/A Note: All insulation joints shall be staggered and adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of 25 lbs/100 ft 2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Ply Sheet: One or more plies of Yosemite Venting Base Sheet strip-mopped with 9-inch wide ribbons of ASTM D312, Type IV hot asphalt spaced 18-inch o.c. One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of 25 lbs./sq. Page 20 of 34
21 Membrane: Surfacing: One ply of Flintlastic FR Cap 30, Flintlastic FR Cap 30 CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR-P CoolStar, Flintlastic Premium FR-P or Flintlastic Premium FR-P CoolStar adhered to base or ply sheet with approved mopping asphalt applied within the EVT range and at a rate of 25 lbs./sq. or one ply of Flintlastic FR Cap 30 T or Flintlastic FR Cap 30 T CoolStar, torch-applied to ply sheet. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 21 of 34
22 Membrane Type: Deck Type 4I: Deck Description: System Type A(8): SBS Modified Lightweight Concrete, Insulated Elastizell Cellular Lightweight Concrete, min 390 psi One or more layer of insulation adhered with approved adhesive. Membrane fully adhered. min. 22ga., Grade 33, Type B vented steel deck attached to steel supports spaced maximum 5ft. o.c. with Tek/5 screws spaced 6 o.c. Steel deck side laps are attached 20 o.c. with Tek/1 screws. Elastizell with Zell-Fibers is applied with an 1/8 slurry coat followed by min. 1 thick EPS holey board and a min. 2 thick top coat fastened with Flintfast #14 fasteners and Flintfast 3 Round Plates at 1:8 ft 2 One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft 2 H-Shield CG, FlintBoard H ISO Cold Minimum 1.5 thick N/A N/A Note: Insulation shall be adhered to the deck with OMG OlyBond 500 adhesive in ¾ wide ribbons spaced 6- inch o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Membrane: Surfacing: One or more plies of Glasbase Base Sheet, All Weather/Empire Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet adhered with Millennium Hurricane Force Membrane Adhesive applied in ½ ¾ wide ribbons spaced 6-inch o.c. One or more plies of Flintlastic FR Cap 30, Flintlastic FR Cap 30 CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR-P CoolStar, Flintlastic Premium FR-P or Flintlastic Premium FR-P CoolStar adhered to base sheet with Millennium Hurricane Force Membrane Adhesive applied in ½ ¾ wide ribbons spaced 6-inch o.c. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 22 of 34
23 Membrane Type: Deck Type 4I: Deck Description: System Type A(9): SBS/APP Modified Lightweight Concrete, Insulated Mearlcrete Lightweight Insulation Concrete, min. 200 psi One or more layer of insulation adhered with approved adhesive Structural concrete with a 3 thick cap of Mearlcrete Lightweight Insulation Concrete, 39 lbs/ft3 wet cast density. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Fastener Density/ft 2 ACFoam IV Minimum 2.0 thick N/A N/A Multi-Max FA-3, ACFoam II or FlintBoard ISO Minimum 1.5 thick N/A N/A ISO 95+ GL, H-Shield, FlintBoard H ISO, H-Shield CG, FlintBoard H ISO Cold or ENRGY 3 Minimum 1.0 thick N/A N/A Insulfoam EPS, 1.0 pcf Minimum ¾ thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener Density/ft 2 SECUROCK Gypsum-Fiber Roof Board Minimum ¼ thick N/A N/A Note: All insulation shall be adhered to the deck with TITESET Roofing Adhesive (3M Polyurethane Foam Insulation Adhesive CR-20) applied in 1.5 ribbons spaced 12 o.c. Adhesive shall be allowed to sit for approx. 1 minute before insulation is applied. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Membrane: Surfacing: One or more layers of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered. One ply of Flintlastic FR Cap 30 T, Flintlastic FR Cap 30 T CoolStar, Flintlastic GTA, Flintlastic GTA CoolStar, Flintlastic GTA-FR or Flintlastic GTA-FR CoolStar torch adhered. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #9) Page 23 of 34
24 Membrane Type: Deck Type 4I: Deck Description: System Type A(10): SBS/APP Modified Lightweight Concrete, Insulated Elastizell Lightweight Insulation Concrete, min. 200 psi One or more layer of insulation adhered with approved adhesive Structural concrete with a 3 thick cap of Range II Elastizell Lightweight Insulation Concrete, 44.4 lbs/ft 3 wet cast density One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Fastener Density/ft 2 ACFoam IV Minimum 2.0 thick N/A N/A Multi-Max FA-3, ACFoam II or FlintBoard ISO Minimum 1.5 thick N/A N/A ISO 95+ GL, H-Shield, FlintBoard H ISO, H-Shield CG, FlintBoard H ISO Cold or ENRGY 3 Minimum 1.0 thick N/A N/A Insulfoam EPS, 1.0 pcf Minimum ¾ thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener Density/ft 2 SECUROCK Gypsum-Fiber Roof Board Minimum ¼ thick N/A N/A Note: All insulation shall be adhered to the deck with TITESET Roofing Adhesive (3M Polyurethane Foam Insulation Adhesive CR-20) applied in 1.5 ribbons spaced 12 o.c. Adhesive shall be allowed to sit for approx. 1 minute before insulation is applied. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Membrane: Surfacing: One or more layers of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered. One ply of Flintlastic FR Cap 30 T, Flintlastic FR Cap 30 T CoolStar, Flintlastic GTA, Flintlastic GTA CoolStar, Flintlastic GTA-FR or Flintlastic GTA-FR CoolStar torch adhered. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #9) Page 24 of 34
25 Membrane Type: Deck Type 4: Deck Description: System Type E(1): SBS Modified Lightweight Concrete, Non-insulated Elastizell Cellular Lightweight Concrete, min 390 psi Base sheet mechanically fastened. min. 22ga., Grade 33, Type B vented steel deck attached to steel supports spaced maximum 5ft. o.c. with Tek/5 screws spaced 6 o.c. Steel deck side laps are attached 20 o.c. with Tek/1 screws. Elastizell with Zell-Fibers is applied with an 1/8 slurry coat followed by min. 1 thick EPS holey board and a min. 2 thick top coat. Membrane: Surfacing: One or more plies of Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Poly SMS Base Sheet or Yosemite Venting Base Sheet mechanically attached to the deck using FM-90 Fasteners spaced 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. One or more plies of Flintlastic FR Cap 30, Flintlastic FR Cap 30 CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR-P CoolStar, Flintlastic Premium FR-P or Flintlastic Premium FR-P CoolStar adhered to base sheet with Millennium Hurricane Force Membrane Adhesive applied in ½ ¾ wide ribbons spaced 6-inch o.c. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 25 of 34
26 Membrane Type: Deck Type 4: Deck Description: System Type E(2): APP Modified Lightweight Concrete, Non-insulated Concrecel Cellular Lightweight Concrete, min 400 psi Base sheet mechanically fastened Structural concrete or ga ASTM A653, Grade SS80 steel deck shall be secured 6 o.c. to structural supports spaced a maximum of 5 ft on center with 5/8 puddle welds. Steel deck side laps are attached 12 o.c. with Traxx/1 fasteners. Followed by Concrecel Bonding agent applied to the deck at rate 1200 sq. ft/gal using a compressed air sprayer. Rigid insulation panels shall be placed in a minimum ¼ slurry-coat of insulating concrete and allowed to cure overnight. The following day the rigid insulation shall be covered with a minimum 2 ¼ topcoat cast of Concrecel. After an additional cure time of 24 hours, Concrecel Curing Compound was roller applied at a rate of 300-sq. ft/gal. Fastening: Ply Sheet: Membrane: Surfacing: One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20 or Flintlastic Poly SMS Base Sheet fastened to the deck as described below: Fasten base sheet to deck with OMG CR Assembled Base Sheet Fasteners spaced 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered or one ply of Flintlastic STA or Flintlastic APP Base T torch adhered. Flintlastic GTA, Flintlastic GTA CoolStar, Flintlastic GTA-FR or Flintlastic GTA-FR CoolStar torch adhered to base or ply sheet. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 26 of 34
27 Membrane Type: Deck Type 4: Deck Description: System Type E(3): SBS Modified Lightweight Concrete, Non-insulated Concrecel Cellular Lightweight Concrete, min 400 psi Base sheet mechanically fastened Structural concrete or ga ASTM A653, Grade SS80 steel deck shall be secured 6 o.c. to structural supports spaced a maximum of 5 ft on center with 5/8 puddle welds. Steel deck side laps are attached 12 o.c. with Traxx/1 fasteners. Followed by Concrecel Bonding agent applied to the deck at rate 1200 sq. ft/gal using a compressed air sprayer. Rigid insulation panels shall be placed in a minimum ¼ slurry-coat of insulating concrete and allowed to cure overnight. The following day the rigid insulation shall be covered with a minimum 2 ¼ topcoat cast of Concrecel. After an additional cure time of 24 hours, Concrecel Curing Compound was roller applied at a rate of 300-sq. ft/gal. Fastening: Ply Sheet: Membrane: Surfacing: One or more plies of Glasbase Base Sheet, All Weather/Empire Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20 or Flintlastic Poly SMS Base Sheet fastened to the deck as described below: Fasten base sheet to the deck with OMG CR Assembled Base Sheet Fasteners spaced 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. or one ply of Flintlastic Ultra Poly SMS Base Sheet torch applied. or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered. One or more plies of Flintlastic GMS, Flintlastic GMS CoolStar, Flintlastic Premium GMS, Flintlastic Premium GMS CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR- P CoolStar, Flintlastic Premium FR-P, Flintlastic Premium FR-P CoolStar, Flintlastic FR Cap 30, Flintlastic FR Cap 30 CoolStar adhered to ply sheet with approved mopping asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR Cap 30 T or Flintlastic FR Cap 30 T CoolStar torch adhered to ply sheet. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 27 of 34
28 Membrane Type: Deck Type 4: Deck Description: System Type E(4): APP Modified Lightweight Concrete, Non-insulated Min. 200 psi. Mearlcrete or min. 160 psi Elastizell Cellular Lightweight Concrete Base sheet mechanically fastened Structural concrete or min. 22 ga., type BW slotted steel deck attached to steel supports spaced maximum 5ft. o.c. (at each flute). Steel deck side laps are attached 18 o.c. with Traxx/1 fasteners or # 10 self-tapping screws. Mearlcrete cast at 40 pcf wet density or Range II Elastizell is applied with an 1/8 slurry coat followed by optional min. 2 thick Star-R- Foam Gripper EPS board or min. 1 thick Apache Corrugated Holey Board or Mearl Corrugated EPS Insulation. A min. 2 thick cap of Mearlcrete or Elastizell is placed over the insulation. Ply Sheet: Membrane: Surfacing: One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet or Yosemite Venting Base Sheet* mechanically attached to the deck using OMG CR Assembled Base Sheet Fasteners or FM-90 Fasteners space 7 o.c. in the 4 side lap and 7 o.c. in two evenly divided, staggered rows in the center of the sheet. *Only with FM-90 One or more plies of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered to the base sheet in a full mopping of approved asphalt applied within the EVT range and at a rate of lbs./sq. or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self adhered or one ply of Flintlastic STA or Flintlastic APP Base T torch adhered. Flintlastic GTA, Flintlastic GTA CoolStar, Flintlastic GTA-FR or Flintlastic GTA-FR CoolStar torch adhered to base or ply sheet. Any of the approved surfacing/coating options listed in Table psf (See General Limitation #7) Page 28 of 34
PRODUCT CONTROL SECTION
MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590
MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315-2590
STANDARD REQUIREMENTS FOR BONDING OR MECHANICAL ATTACHMENT OF INSULATION PANELS AND MECHANICAL ATTACHMENT OF ANCHOR AND/OR BASE SHEETS TO SUBSTRATES
ROOFING APPLICATION STANDARD (RAS) No. 117 STANDARD REQUIREMENTS FOR BONDING OR MECHANICAL ATTACHMENT OF INSULATION PANELS AND MECHANICAL ATTACHMENT OF ANCHOR AND/OR BASE SHEETS TO SUBSTRATES Scope 1.1.
APPENDIX 1: ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE
APPENDIX 1: ATTACHMENT REQUIREMENTS FOR WIND UPLIFT NCE Table Application Type Description Page 1A-1 Wood New, Reroof (Tear-Off), Recover C-1 Mechanically Attached Insulation, Bonded Roof Cover 4 1A-2
ROOFING APPLICATION STANDARD (RAS) No. 150 PRESCRIPTIVE BUR REQUIREMENTS
ROOFING APPLICATION STANDARD (RAS) No. 150 PRESCRIPTIVE BUR REQUIREMENTS 1. 2. 3. 3.0 Scope 1.1 This application standard shall be used where the authority having jurisdiction has adopted its use, and
Re-Cover Board-3. Insulation for Above the Deck ROOF WALL SPECIALTY
Insulation for Above the Deck WALL SPECIALTY PRODUCT DESCRIPTION Rmax Re-Cover Board-3 is an energy-efficient thermal insulation board composed of a closed-cell polyisocyanurate (polyiso) foam core bonded
CHAPTER 7: Building Systems ROOFING SYSTEMS
ROOFING SYSTEMS Purpose Examples 1. Shingle roof system 2. Metal roof with blanket insulation 3. Metal roof with rigid insulation 4. Built-up asphalt roof system 5. Single-ply roof system 6. Modified Bitumen
SECTION 07550 - MODIFIED BITUMINOUS MEMBRANE ROOFING. A. Vapor barrier (base ply); cover board at existing roof deck.
SECTION 07550 - PART I GENERAL 1.01 SECTION INCLUDES A. Vapor barrier (base ply); cover board at existing roof deck. B. Roof insulation at new roof deck. C. Modified bitumen membrane. D. Fluid applied
Design No. P736 September 26, 2003. Restrained Assembly Ratings 1, 1-1/2 or 2 Hr. (See Items 3, 7 and 8A)
Design No. P736 September 26, 2003 Restrained Ratings 1, 1-1/2 or 2 Hr (See Items 3, 7 and 8A) Ratings 1, 1-1/2 or 2 Hr (See Items 3, 7 and 8A) Beam Ratings 1, 1-1/2 or 2 Hr (See Items 7 and 8A) 1. Beam
DIVISION: 07 00 00 THERMAL AND MOISTURE PROTECTION SECTION: 07 41 13 METAL ROOF PANELS REPORT HOLDER: FIRESTONE BUILDING PRODUCTS COMPANY, LLC
0 ICC ES Report ICC ES (800) 423 687 (62) 699 043 www.icc es.org 000 Most Widely Accepted and Trusted ESR 3422 Reissued 09/201 This report is subject to renewal 09/2016. DIVISION: 07 00 00 THERMAL AND
Commercial Roof Systems Selection Guide
CertainTeed Commercial Roof Systems Selection Guide Good Better Best. Don't specify less. The chart below is a quick guide to choosing the right roof system for your needs. Please note: the best roofs
1. Adhered KEE membrane roofing system. 2. Mechanically fastened KEE membrane roofing system.
SECTION 075416 - PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Adhered KEE membrane roofing system. 2. Mechanically fastened KEE membrane roofing system. 1.2 PERFORMANCE REQUIREMENTS A. Solar Reflectance
COMMERCIAL BUILDING APPLICATIONS
EXPANDED POLYSTYRENE FOR COMMERCIAL BUILDING APPLICATIONS www.falconfoam.com Commercial Building Ap Expanded Polystyrene Insulation Falcon Foam leads the commercial building industry with products that
TABLE OF CONTENTS. Roof Decks 172 B, BA, BV Deck N, NA Deck. Form Decks 174.6 FD,.6 FDV Deck 1.0 FD, 1.0 FDV Deck 1.5 FD Deck 2.0 FD Deck 3.
Pages identified with the NMBS Logo as shown above, have been produced by NMBS to assist specifiers and consumers in the application of New Millennium Building Systems Deck products. Pages identified with
UL Online Certifications Directory
UL Online Certifications Directory Home Quick Guide Contact Us UL.com TGFU.R11183 Roofing Systems Page Bottom Roofing Systems See General Information for Roofing Systems PACTIV CORP SUITE 175 2100 RIVEREDGE
NRDCA 400 GUIDELINE FOR FIELD APPLICATION of LIGHTWEIGHT INSULATING CONCRETE REROOFING/RECOVER SYSTEMS
NRDCA 400 GUIDELINE FOR FIELD APPLICATION of LIGHTWEIGHT INSULATING CONCRETE REROOFING/RECOVER SYSTEMS The (NRDCA) has prepared this document to provide customers and installers information that the industry
AUTHORIZATION TO MARK
AUTHORIZATION TO MARK This authorizes the application of the Certification Mark(s) shown below to the models described in the Product(s) Covered section when made in accordance with the conditions set
http://www.floridabuilding.org/pr/pr_app_dtl.aspx?param=wgevxqwtdqtkahqb3dx8wn...
Florida Building Code Online http://www.floridabuilding.org/pr/pr_app_dtl.aspx?param=wgevxqwtdqtkahqb3dx8wn... Page 1 of 2 8/3/2015 BCIS Home Log In User Registration Hot Topics Submit Surcharge Stats
Durapax Coal Tar BUR Application Guide
400 Old Reading Pike, Suite 304 Pottstown, PA 19464 Tel: 610-579-9075 Fax: 610-323-0115 www.durapax.com Durapax Coal Tar BUR Application Guide DESIGN CONSIDERATIONS The proper specifications of any roof
Commercial Roof Systems
CertainTeed Commercial Roof Systems 2016 SELECTION GUIDE PAGE HEAD Primer Insulation Self-Adhering SBS Modified Bitumen Fasteners SBS Modified Bitumen Make the right choice Experts in commercial roofing
ROOF CONSTRUCTION SCIENCE (METCT092)
ROOF CONSTRUCTION SCIENCE (METCT092) This training program is intended for applicators that are interested in gaining an understanding of the various technologies incorporated in roof systems, including
FAST FACTS ADVANTAGES OF MULTI PLY BUILT-UP ROOFING. Asphalt Roofing Manufacturers Association
FAST FACTS ADVANTAGES OF MULTI PLY BUILT-UP ROOFING Roofing Manufacturers Association Why is a built-up roof considered a multi-ply roof? ARMA defines a built-up roofing system as a roof where multiple
January 2005 Approval Guide 3-110 ES Products Inc FM Approved Combinations and Assemblies
3-110 ES Products Inc FM Approved Combinations and Assemblies Roof Cover: Substrate: Application: Hail Rating: ASTM E 108: Eraguard 2000 Primer FR is spray, roller or brush applied to metal panel roofs
Firestone Modified Bitumen Roofing Systems DURABLE. RELIABLE. SUSTAINABLE
Firestone Modified Bitumen Roofing Systems DURABLE. RELIABLE. SUSTAINABLE I n t r o d u c t i o n t o M o d i Acres of Roofing. Decades of Performance. Over the past 20 years, Firestone Building Products
CertainTeed. Self-Adhering Roof Systems for Low Slope Residential Roofs
CertainTeed Self-Adhering Roof Systems for Low Slope Residential Roofs Goes down fast. Stays on strong. Flintlastic SA performs in all the right ways. What s more important to you? Speed of installation,
BITUMEN-POLYMER WATERPROOFING MEMBRANE, MADE FROM SELECT APP AND DISTILLED BITUMEN, REINFORCED WITH SPUNBOND POLYESTER FABRIC.
93-106 Revised March 2007 BITUMEN-POLYMER WATERPROOFING MEMBRANE, MADE FROM SELECT APP AND DISTILLED BITUMEN, REINFORCED WITH SPUNBOND POLYESTER FABRIC. BITEC APM-4.5T is a torch applied, mineral surfaced,
Smooth cap sheet - 0-10 SQ $ 139.00. Smooth cap sheet - 11-50 SQ $ 63.00. Smooth cap sheet - 51-100 SQ $ 36.00 Smooth cap sheet - 101-200 SQ $ 36.
Demolition/Removal of Work 4-ply built up roofing to the insulation (smooth cap sheet) Smooth cap sheet - 0-10 SQ $ 63.00 Smooth cap sheet - 11-50 SQ $ 63.00 Smooth cap sheet - 51-100 SQ $ 35.00 Smooth
GENERAL REQUIREMENTS HENRY WARRANTED COMMERCIAL ROOFING SYSTEMS
GENERAL REQUIREMENTS HENRY WARRANTED COMMERCIAL ROOFING SYSTEMS 1.0 STATEMENT OF POLICY The overall performance of a roofing system can be affected by factors other than the roof system installation. Henry
C e r t a i n Te e d. 2 0 1 2 S e l e c t i o n G u i d e
C e r t a i n Te e d Commercial Roof Systems 2 0 1 2 S e l e c t i o n G u i d e make the right choice Experts in residential and commercial roofing CertainTeed is a leading manufacturer of commercial
Laboratory Report P12850.03.09. Simulated Wind Uplift Testing of Adhered Single-Ply Roofing Systems in accordance with FM Standard 4470, Appendix C
Simulated Wind Uplift Testing of Adhered Single-Ply Roofing Systems in accordance with FM Standard 4470, Appendix C Prepared for: 2100 River Edge Parkway, Suite 175 Atlanta, GA 30328 Date of Issuance:
CREEK Technical Services, LLC
EVALUATION REPORT 2010 FLORIDA BUILDING CODE Manufacturer: Henry Company Report Issued February 20, 2013 999 North Sepulveda Blvd., Suite 800 El Segundo, CA 90245 (800) 486-1278 Manufacturing Plants: Quality
RESIDENTIAL ROOFING & RE-ROOFING, ROOF VENTILATION AND ROOF SHEATHING REQUIREMENTS MICHIGAN RESIDENTIAL CODE 2000
RESIDENTIAL ROOFING & RE-ROOFING, ROOF VENTILATION AND ROOF SHEATHING REQUIREMENTS MICHIGAN RESIDENTIAL CODE 2000 SECTION R905 REQUIREMENTS FOR ROOF COVERINGS R905.1 Roof covering application. Roof coverings
Florida Building Code Approval
Florida Building Code Approval GAF-Elk Roof Underlayments Updated 10/13/09 Your Best and Safest Choice Quality You Can Trust Since 1886! Florida Building Code Online http://floridabuilding.org/pr/pr_app_dtl.aspx?param=wgevxqwtdqtbnbey5v%2boq...
CHICAGO ROOFING CONTRACTORS ASSOCIATION
CHICAGO ROOFING CONTRACTORS ASSOCIATION JANUARY 22, 2016 Roofing Claims & Lawsuits Stephen M. Phillips Hendrick, Phillips, Salzman & Flatt, P.C. 230 Peachtree Street, Suite 2500 Atlanta, GA 30303 (404)
TEST PROCEDURE FOR FIELD WITHDRAWAL RESISTANCE TESTING
TESTING APPLICATION STANDARD (TAS) No. 105-98 TEST PROCEDURE FOR FIELD WITHDRAWAL RESISTANCE TESTING 1. Scope 1.1 This Testing Application Standard (TAS) covers procedures for withdrawal resistance testing
Mop it. Stick it. Spread it.
A w a p l a n S B S - m o d i f i e d r o l l r o o f i n g Mop it. Stick it. Spread it. Same proven performance. Now with more ways than ever to apply it. 1 inch 1.5 inch However you apply products, count
APPLICATION INFORMATION FOR RESIDENTIAL ROOFING AND RESIDENTIAL ROOFING PACKET
Environmental Protection and Growth Management Department PERMITTING, LICENSING AND CONSUMER PROTECTION DIVISION 1 N. University Drive, Box #302 Plantation, Florida 33324 954-765-4400 www.broward.org/permittingandlicensing
TARRANT COUNTY DETAIL STANDARDS
TARRANT COUNTY DETAIL STANDARDS 1. Standard Coping 2. Coping at End Wall 3. Standard Sheet Metal Engagement Details 4. Gravel Guard 5. Gravel Guard Wall Termination 6. Gravel Guard, Gutter, and Downspout
SINGLE FAMILY RESIDENCE HURRICANE MITIGATION APPLICATION
SINGLE FAMILY RESIDENCE HURRICANE MITIGATION APPLICATION As of October 1, 2007, this mitigation form must be submitted as part of the roofing permit application package. Secondary water barrier (if applicable)
Roof Systems Overview
Roof Systems Overview Cold Applied Built-Up Roofing Systems BURmastic Tremco s line of cold applied built-up roofing systems. BURmastic 200 Combines Tremco s expertise in asphalt blending technology with
Roofing Systems. There are many different systems, each with it's own special requirements and benefits. Browse through all the options below.
Roofing Systems There are many different systems, each with it's own special requirements and benefits. Browse through all the options below. BUR (Built-Up Roofing) Built-Up-Roofing, BUR is a roof that
Roof insulations must perform the basic function of helping to control fluctuations in building interior temperature
Thermal Values Roof insulations must perform the basic function of helping to control fluctuations in building interior temperature relative to changing exterior temperatures. By reducing interior temperature
DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION: 06 05 83 SHOP APPLIED WOOD COATINGS SECTION: 06 16 00 SHEATHING REPORT HOLDER:
0 ICC ES Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 Most Widely Accepted and Trusted ESR 1365 Reissued 04/2016 This report is subject to renewal 04/2017. DIVISION: 06 00 00 WOOD, PLASTICS
WESTERN COOL ROOF SYSTEMS Sustainable - Energy Efficient FLUID APPLIED REINFORCED ROOF SYSTEM
WESTERN COOL ROOF SYSTEMS Sustainable - Energy Efficient FLUID APPLIED REINFORCED ROOF SYSTEM SPECIFICATION NO. SMAA-2P-8xE UPGRADE SMOOTH SURFACE / CAP SHEET / SINGLE PLY 2 PLY POLYESTER REINFORCED ACRYLIC
Commercial Roof Systems
CertainTeed Commercial Roof Systems 2015 SELECTION GUIDE PAGE HEAD Primer Insulation Self-Adhering SBS Modified Bitumen Fasteners SBS Modified Bitumen Make the right choice Experts in commercial roofing
Please read the entire document before purchasing and installing any of these products
Please read the entire document before purchasing and installing any of these products USA SBS UNDERLAYMENT ROOFING UNDERLAYMENT SBS Mineral Surfaced MINERAL SURFACE CAP SHEET Ice and Water Protection
UL Online Certifications Directory
UL Online Certifications Directory OCD Home Quick Guide Contact Us UL.com BXUV.D972 Fire Resistance Ratings - ANSI/UL 263 Page Bottom Fire Resistance Ratings - ANSI/UL 263 See General Information for Fire
THE EFFECT OF REFLECTIVE ROOF COATINGS ON THE DURABILITY OF ROOF SYSTEMS
THE EFFECT OF REFLECTIVE ROOF COATINGS ON THE DURABILITY OF ROOF SYSTEMS Joseph W. Mellott II and Donald C. Portfolio ROOF COATING MANUFACTURERS ASSOCIATION International Roofing Expo TU-03 Technical March
16 2 10.3 Materials and Colors
16 2 10.3 Materials and Colors To create a harmonious and coherent image for each development, building designs shall pay close attention to choice of materials and colors. Building construction shall
Firestone SBS Modified Bitumen Roofing System Design and Application Guide
SBS Modified Bitumen Roofing System Design and Application Guide October, 2013 Table of Contents 1.01 Introduction... 1 1.01.1.1 General Considerations... 1 1.01.1.2 Warranty... 3 1.01.1.3 QUALITY ASSURANCE...
Colorado State University. Durrell Center Roof Repair
Colorado State University Durrell Center Roof Repair SPECIFICATION: POLYURETHANE FOAM ROOFING l.0 GENERAL REQUIREMENTS The successful application of a polyurethane foam roofing system is dependent upon
Polyiso Insulation. Tapered Polyiso Insulation
All Firestone Polyiso insulations have a polyisocyanurate foam core. The standard compressive strength is 20 psi, but 25 psi is also available, upon request. Different facers are used to make specific
tamko.com RESIDENTIAL ROOFING PRODUCT GUIDE
tamko.com RESIDENTIAL ROOFING PRODUCT GUIDE RESIDENTIAL ROOFING PRODUCT GUIDE SHINGLES / LAMINATED LIMITED DESIGN PRODUCT SPECIFICATIONS WARRANTY CERTIFICATIONS U.L. Laminated Shadowtone Choose From Classic
Best Practices in Roof Design: Sustainable Energy Efficient Reroofing
Best Practices in Roof Design: Sustainable Energy Efficient Reroofing Best Practice Roof Design: Sustainable Energy Efficient Reroofing Presented by Edis Oliver, PE Principal 9511 Lake Creek Parkway Austin,
FIRESTONE BUILT-UP ROOFING SYSTEMS APPLICATION GUIDE 3/14/2011
FIRESTONE BUILT-UP ROOFING SYSTEMS APPLICATION GUIDE TABLE OF CONTENTS 2.01.1 GENERAL......2 2.02.1 JOB SITE CONSIDERATIONS (CAUTION AND WARNINGS)...2 2.03.1 ROOF SUBSTRATE PREPARATION...2 2.04.1 WOOD
CHAPTER VII. TITLE: STANDARDS FOR NEW ROOFING July 2015 CONSTRUCTION, RE-ROOFING CONSTRUCTION AND ROOFING SYSTEM GUARANTEE REQUIREMENTS
TITLE: STANDARDS FOR NEW ROOFING CONSTRUCTION, RE-ROOFING CONSTRUCTION AND ROOFING SYSTEM GUARANTEE REQUIREMENTS Responsible Organization: Office of Facilities Planning Instructions: This Manual supersedes
ANSI/SPRI WD-1 Wind Design Standard Practice for Roofing Assemblies. Table of Contents. 1.0 Introduction...2. 2.0 Methodology...2
Standard Practice f Table of Contents 1.0 Introduction...2 2.0 Methodology...2 Appendix A...7 Insulation Board Fastening Patterns 4 feet 4 feet Boards Adhered Membranes...8 Insulation Board Fastening Patterns
Asphalt Shingle Application Requirements
Alberta Allied Roofing Association Asphalt Shingle Application Requirements Section 1 Roof Decks 1.1 General Asphalt Shingles are not permitted to be installed directly over rigid insulation. When Asphalt
BXUV.D946 - Fire Resistance Ratings - ANSI/UL 263. Design/System/Construction/Assembly Usage Disclaimer. Fire Resistance Ratings - ANSI/UL 263
BXUV.D946 Fire Resistance Ratings - ANSI/UL 263 Page Bottom Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements
EPDM. Roofing systems
Roofing systems Our Promise Through ongoing interchange of experiences with contractors, Mule-Hide keeps on top of the latest roofing requirements and solutions Trusted in roofing since 1906, Mule-Hide
Prices Effective April 1, 2016
Domestic U.S. Warranty Pricing Guide Longer term warranties have additional installation requirements and not all warranty terms are available for all roofing specifications. Please refer to the Firestone
ATLAS Roofing Products
ATLAS Roll Roofing Products World s Largest producer of roofing s Preferred by roofing professionals. Atlas has you covered on every part of the job, even what goes under your roofing. We are proud to
A. Roofing Terminology: Definitions in ASTM D 1079 and glossary in NRCA's "The NRCA Roofing and Waterproofing Manual" apply to work of this Section.
SECTION 075419 POLYVINYL CHLORIDE (PVC) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
HOT ASPHALT BUILT-UP ROOFING SYSTEMS MORE LAYERS MEANS MORE PROTECTION
HOT ASPHALT BUILT-UP ROOFING SYSTEMS MORE LAYERS MEANS MORE PROTECTION ADVANCED TECHNOLOGY FROM OWENS CORNING TRUMBULL ASPHALT TruLo Lo Odor and TruLo Max asphalt raising the roof on asphalt performance.
Asphalt-Applied and Cold Application Built-Up Roofing Application Guide
1.0 General Information 1.1 The following section provides the application specifications currently available from Johns Manville (JM) for built-up roofing membranes and covers both hot asphalt and cold
SBS-Modified Bitumen Roof Systems
SBS-Modified Bitumen Roof Systems High performance systems from the developers of SBS-modified bitumen. Siplast s Paradiene 20/30 was selected for the Library of Congress in Washington D.C. Seven hundred
Design No. L556. Design No. L556
1 of 9 3/17/2015 6:15 PM Design No. L556 BXUV.L556 Fire Resistance Ratings - ANSI/UL 263 Page Bottom Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted
Sheet A-1 KEY SHEET A-1. Football Roof Plan SHEET A-2 SHEET A-3 SHEET A-4. LaCross Roof Plan. Soccor 2 Roof Plan 88' 45' 87' 46' 45' 45' 10' 3' 25'
Sheet A-1 SHEET A-1 Football Roof Plan 5 LaCross Roof Plan 5 88' 87' SHEET A- 1 DRIP EDGE WITH STANDING SEAM PANEL 2 RAKEWALL SHEET A- RIDGE HIP HEAD WALL 11700 Pierson Rd. Wellington, FL. 1 Soccor 2 Roof
Polyiso Insulation. Tapered Polyiso Insulation
Product Name ISO 95+ HailGard ISO 95+ Woodfiber Composite Polyiso Insulation Effective 3/1/2016 All Firestone Polyiso insulations have a polyisocyanurate foam core. The standard compressive strength is
ROOF ASSEMBLIES CHAPTER 9
CHAPTER 9 ROOF ASSEMBLIES SECTION R901 GENERAL R901.1 Scope. The provisions of this chapter shall govern the design, materials, construction and quality of roof assemblies. SECTION R902 ROOF CLASSIFICATION
Proven roofing SyStemS
Proven Roofing Systems Above all. Roofing challenges are never over our heads At GenFlex, we live to tackle and solve the toughest challenges in roofing. The result is a full line of proven, durable roofing
COMMERCIAL ROOFING. Learning Objectives. Commercial Roofing Fundamentals May 2, 2012
COMMERCIAL ROOFING The Fundamentals Firestone Building Products is a Registered Provider with the American Institute of Architects Continuing Education Systems. Credit earned on completion of this program
Built-up roofing solutions with rigid insulation boards on concrete decks for new-build and refurbishment E-a5
Cl Sfb (27-9) Rn7 M2 December 2004 Built-up roofing solutions with rigid insulation boards on concrete decks for new-build and refurbishment E-a5 Fesco, Fesco S, Retrofit, Retrofit S, Fesco Fillet, PF,
SECTION 15190 HVAC INSULATION. A. All work specified in this Section is subject to the provisions of Section 15010.
SECTION 15190 HVAC INSULATION PART ONE - GENERAL PART 1 - GENERAL 1.01 DESCRIPTION A. All work specified in this Section is subject to the provisions of Section 15010. B. All insulation products shall
CITIZENS PROPERTY INSURANCE CORPORATION. STREET ADDRESS: 14300 Gulf Blvd, Maderia Beach, FL 33708 6 Six story masonry residence
CITIZENS PROPERTY INSURANCE CORPORATION BUILDING TYPE II AND III MITIGATION VERIFICATION AFFIDAVIT This affidavit must be completed to capture mitigation features applicable to a Type II (4 to 6 story)
CF-Mesa, CF-Light Mesa, CF-Flute, CF-Metl-Plank, CF-Striated, CF-Santa Fe, CF-Architectural Flat, CF...
Building Insulations - Walls and Ceilings (FM Approval Numbers 4411, 4651, 4880, 4881, 4882) Insulating materials may occur in building construction to reduce heat or sound transmission through a wall,
ICC-ES Evaluation Report Reissued September, 2010 This report is subject to re-examination in one year.
ICC-ES Evaluation Report ESR-2270 Reissued September, 2010 This report is subject to re-examination in one year. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council
CONTINENTAL MATERIALS, INC. ALL-WEATHER APP INSTALLATION GUIDELINES
CONTINENTAL MATERIALS, INC. ALL-WEATHER APP INSTALLATION GUIDELINES Page 1 APP INSTALLATION GUIDELINES This guide provides instructions for the installation of CMI All Weather APP roofing materials. Any
ROOF FLASHING SPRINGLOK FLASHING SYSTEM FEATURES & BENEFITS PRODUCT DESCRIPTION
SPRINGLOK SYSTEM PRODUCT DESCRIPTION FEATURES & BENEFITS Fry Reglet offers five flashing systems, each tailored for a particular type of substrate so you can get exactly what you need. SM Surface mounted
August 2013 State Wide Roof Asset Mgmt Program DCAM #14039(2) 14040(4) 14041(5) PERFORMANCE SPECIFICATIONS
1.0 SCOPE OF WORK/SUPPLEMENTARY CONDITIONS PERFORMANCE SPECIFICATIONS Pursuant to the provisions of O.S. 61 and Title 580 Department of Central Services, Chapter 20 Construction and Properties Division
SECTION 07560 FLUID APPLIED ROOFING (LIGHT TRAFFIC DECKS OVER CONCRETE)
SECTION 07560 FLUID APPLIED ROOFING (LIGHT TRAFFIC DECKS OVER CONCRETE) PART 1 GENERAL 1.1 DESCRIPTION 1. Fluid applied flexible acrylic waterproofing system over concrete. This work shall include the
MASTICS. 275 Centre St., Unit 15 Holbrook, MA 02343 (617) 996-0400. 15236 Shedd Rd. Middlefield, OH 44062 (440) 345-6900
MASTICS AQUAHALT MASTIC- A AQUAHALT MASTIC- A is a heavily consistent, trowel- applied mastic formulated with refined asphalt, fibers and solvent. It is designed as an all- purpose repair cement, it bonds
HIGH PERFORMANCE PRE-APPLIED SYSTEM FOR BLIND SIDE & BELOW GRADE WATERPROOFING APPLICATIONS
BSW HIGH PERFORMANCE PRE-APPLIED SYSTEM FOR BLIND SIDE & BELOW GRADE WATERPROOFING APPLICATIONS BSW is a fully reinforced Pre-Applied system membrane designed for horizontal and vertical external blind-side
LEGACY REPORT. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council RETAINED ON U.S.
ICC-ES Legacy Report ER-5043* Reissued March 2004 www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council Legacy report on the 1997 Uniform Building Code DIVISION: 09
EXPANDED POLYSTYRENE (EPS) INSULATION BOARD SPECIFICATIONS
EXPANDED POLYSTYRENE (EPS) INSULATION BOARD SPECIFICATIONS 1. SCOPE 1.1 This specification covers the type, physical properties and dimensions of Expanded Polystyrene Insulation Board intended for use
ALPHA 15-Year Permathane II FR w/granules
ALPHA 15-Year Permathane II FR w/granules Section 07 57 13 Sprayed Polyurethane Foam Roofing Guide Specification PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Furnish all labor, materials, tools and
CITY OF FLORIDA CITY Building and Zoning Department 404 West Palm Drive Florida City, FL 33034 305-247-8222 ROOFING PERMIT APPLICATION
IF SUBSIDIARY, PROVIDE MASTER PERMIT NUMBER HERE: CITY OF FLORIDA CITY Building and Zoning Department 404 West Palm Drive Florida City, FL 33034 305-247-8222 ROOFING PERMIT APPLICATION Location of Improvements
PTS HELICAL PIERS INSTALLATION SPECIFICATIONS NOTICE
FORM A PTS HELICAL PIERS INSTALLATION SPECIFICATIONS NOTICE The following suggested specifications are written as a guide to assist the specifier in writing his own specifications. Specific circumstances
HexWeb CR III Corrosion Resistant Specification Grade Aluminum Honeycomb
Corrosion Resistant Specification Grade Aluminum Honeycomb Description 5052 and 5056 expanded aerospace grade aluminum honeycomb materials are available in a wide selection of cell sizes and foil gauges.
tamko.com RESIDENTIAL ROOFING PRODUCT GUIDE
tamko.com RESIDENTIAL ROOFING PRODUCT GUIDE RESIDENTIAL ROOFING PRODUCT GUIDE SHINGLES / LAMINATED LIMITED DESIGN PRODUCT SPECIFICATIONS WARRANTY CERTIFICATIONS Metric Size Shadowtone Choose From Classic
Final inspections are completed by site visit only. Access to fenced yards shall be planned.
ROOFING RESIDENTIAL BUILDING INSPECTIONS DEPARTMENT www.ci.blaine.mn.us This handout is intended only as a guide and is based in part on the 2015 Minnesota State Building Code, Blaine City ordinances,
Residential Roofing Guide
Residential Roofing Guide TABLE OF CONTENTS Building Detail and Accessories...... 1 Panel Introduction and Handling...... 2 Cutting and Trimming.... 3 Roof Preparation..... 3 Roof Slope..... 3 Re-roofing...
CHAPTER 6 ASPHALT ROLL ROOFING
CHAPTER 6 ASPHALT ROLL ROOFING Section I. DESCRIPTION AND GENERAL DISCUSSION 6.1.1 General 6.1.3 Mineral-Surfaced Asphalt roll roofing is roofing in sheet form Mineral-surfaced roll roofing is composed
FIRESTONE APP ROOFING SYSTEMS APPLICATION GUIDE TABLE OF CONTENTS
FIRESTONE APP ROOFING SYSTEMS APPLICATION GUIDE TABLE OF CONTENTS 2.01.1 GENERAL...2 2.02.1 JOB SITE CONSIDERATIONS (CAUTION AND WARNINGS)...2 2.03.1 ROOF SUBSTRATE PREPARATION...2 2.04.1 WOOD NAILER LOCATION
ITEM 599.06060008 THERMOPLASTIC MEMBRANE ROOFING
DESCRIPTION Construct adhered membrane roofing system, roof insulation, and vapor retarder in accordance with these specifications. MATERIALS: General: Provide installed roofing membrane and base flashings
SECTION 07530 SINGLE PLY MEMBRANE ROOFING. 4. Minor repair to adjacent clay tile roofing and flashings.
SECTION 07530 PART 1 - GENERAL 1.01 DESCRIPTION A. This Section includes the flowing: 1. Removal of existing roofing membrane. Existing bur roof has one overlay and penetration mastic is asbestos containing.
Tremco Fire Protection Systems Group Technical Bulletin
Compartmentalization products and design play a key role in protecting lives and property from fire. Understanding the tools and techniques available for firestopping is of utmost importance to designers,
SECTION 070153 EPDM ROOFING REPAIR. B. Wood Nailers and Blocking: Section 061053.
SECTION 070153 EPDM ROOFING REPAIR PART 1 GENERAL 1.01 RELATED WORK SPECIFIED ELSEWHERE A. Restricted Work Period: Section 011100. B. Wood Nailers and Blocking: Section 061053. C. Flashing And Trim: Section
NEW ELECTRICAL SUBSTATION Building 300 SECTION 07 53 23 ETHYLENE-PROPYLENE-DIENE-MONOMER ROOFING WORK
ETHYLENE-PROPYLENE-DIENE-MONOMER ROOFING WORK PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within
SEAMS SEAMING USING SEAM TAPE
SEAMING USING SEAM TAPE SEAMS The membrane should be positioned so that the width of the seam is 3. Remove excess chalk from a chalk line by snapping the line into the air and then chalk a line one-quarter