1 MASTICS AQUAHALT MASTIC- A AQUAHALT MASTIC- A is a heavily consistent, trowel- applied mastic formulated with refined asphalt, fibers and solvent. It is designed as an all- purpose repair cement, it bonds tightly and remains soft and pliable. AQUAHALT ALUMINUM MASTIC AQUAHALT ALUMINUM MASTIC is a cold- applied, multi- purpose waterproofing mastic formulated with premium grade aluminum that provides a reflective finish. It is ideal for use as a repair cement on asphalt roof systems and flashings eliminating the additional labor necessary to aluminize standard roof cements. AQUAHALT MASTIC- T AQUAHALT MASTIC- T is a tar- based mastic for repairing a wide variety of roofing problems. It contains penetrating oils, plasticizing agents, and reinforcing fibers. AQUAHALT MASTIC- T's resilient formulation is designed expressly for repairs on tar roof membrane systems. It is easily applied directly from the container to seal breaks or blisters in the roof membrane. Warming may be required in cool weather. AQUAHALT MASTIC- T may be applied to wet surfaces. Because of this characteristic, AQUAHALT MASTIC- T may be used as an emergency mastic even on asphalt roofs for temporary repairs. STRETCH- SEAL STRETCH- SEAL is a non- asbestos, SBS modified, asphalt- based mastic for repairing a wide variety of roofing problems. It contains oils, plasticizing agents, reinforcing fibers and surfactants for improving adhesion to damp surfaces. STRETCH- SEAL s resilient formulation is designed expressly for repairs on roof systems and components such as pitch pans. It is easily applied directly from the container to remedy breaks, holes, or blisters in the roof membrane. STRETCH- SEAL PLUS STRETCH- SEAL PLUS is a specially formulated blend of select asphalt, fibers, solvent, and SBS polymer manufactured to a trowel consistency. It is designed to adhere modified bitumen sheets to suitable horizontal substrates. Works great adhering seams on modified bitumen sheets. It provides long lasting adhesion and a watertight seal. Can be used with SBS or APP membranes. The App membrane must not have a polyethylene burn- off backing. WEATHER PATCH WEATHER PATCH is a fibrated solvent- based asphalt mastic or brush grade which can be used under an extreme range of weather and temperature conditions. Its unique chemical additives allow successful application even on wet surfaces. WEATHER PATCH does not required a dry surface; brush grade may be applied into ponding conditions. Regardless of weather or temperature, existing leaks can be repaired at any time. RUBBER- FLASH RUBBER- FLASH is a heavy bodied, trowel grade adhesive. It is butyl based and asbestos free with excellent adhesion to most roofing substrates. RUBBER- FLASH stays flexible throughout its service life, ensuring good adhesion and unbroken contact to uneven surfaces. This results in a watertight bond even under conditions of normal roof movement. Also available in black with comparable properties. ARS MASTICS SG/WG ARS- MASTICS are made with a careful selection of ingredients to produce the highest grade of product in the industry. They are of heavy consistency, trowel applied materials formulated with a refined asphalt, quality fillers and solvent. Designed as all purpose repair cements, they bond tightly and remain soft and pliable. They withstand summer heat and winter cold without cracking. They provide a durable, waterproof seal, meeting all requirements of ASTM- D
2 ARS BLACK FLASHING MASTIC SB ARS BLACK FLASHING MASTIC SB is a heavy bodied, trowel grade adhesive. It is butyl based and asbestos free, with excellent adhesion to most roofing substrates. ARS BLACK FLASHING MASTIC SB stays flexible throughout its service life, ensuring good adhesion and unbroken contact to uneven surfaces. This results in a watertight bond even under conditions of normal roof movement. ARS ELASTOMERIC MASTIC ARS ELASTOMERIC MASTIC is a specially modified trowel applied mastic formulated with synthetic rubber, functional fillers, and solvents. ERS- 306 quickly develops in to a seamless rubber seal. Its unusual combination of high tensile strength and elongation and recovery make it the perfect cement to use in high stress areas. It will withstand rooftop movement and vibrations without splitting. This cement will withstand changing seasons and mechanical stresses as it forms a rubber- like seal that will form a waterproof seal for many years. ARS HP RUBBERIZED MASTIC ARS HP RUBBERIZED MASTIC is a specially formulated blend of select asphalt, fibers, solvent, and SBS polymer manufactured to a trowel consistency. It is designed to adhere modified bitumen sheets to suitable horizontal substrates. Works great adhering seams on modified bitumen sheets. It provides long lasting adhesion and a watertight seal. Can be used with SBS or APP membranes. The APP membrane must not have a polyethylene burn- off backing. ARS HS ASPHALT MASTIC ARS HS ASPHALT MASTIC is a non- asbestos, SBS modified, asphalt- based mastic for repairing a wide variety of roofing problems. It contains oils, plasticizing agents, reinforcing fibers and surfactants for improving adhesion to damp surfaces. ARS HS ASPHALT MASTIC s resilient formulation is designed expressly for repairs on roof systems and components such as pitch pans. It is easily applied directly from the container to remedy breaks, holes, or blisters in the roof membrane. ARS TAR MASTIC ARS TAR MASTIC is a select blend of refined coal tar pitch, aromatic solvents, non- asbestos fibers and fillers, and wet adhesion surfactants that is designed for compatibility with coal tar pitch roofing and waterproofing systems. ARS WATER CUT- OFF MASTICS ARS WATER CUT- OFF MASTIC is a butyl- based, one- component mastic designed specifically for sealing American Roofing Systems membranes to wood, concrete, metal, plastic and other substrates. ARS WET SURFACE REPAIR MASTIC ARS WET SURFACE REPAIR MASTIC is a fibrated solvent- based asphalt mastic. It is available in trowel or brush grade which can be used under an extreme range of weather and temperature conditions. Its unique chemical additives allow successful application even on wet surfaces. ARS WET SURFACE REPAIR MASTIC does not require a dry surface; brush grade may be applied into ponding conditions. Regardless of weather or temperature, existing leaks can be repaired at any time. ARS WHITE FLASHING MASTIC SB ARS WHITE FLASHING MASTIC SB is a heavy bodied, trowel grade adhesive. It is butyl based and asbestos free, with excellent adhesion to most roofing substrates. ARS WHITE FLASHING MASTIC SB stays flexible throughout its service life, ensuring good adhesion and unbroken contact to uneven surfaces. This results in a watertight bond even under conditions of normal roof movement. Also available in black with comparable properties. WHITE HP MASTIC WHITE HP MASTIC is a water- based, high solids elastomeric mastic/sealant utilizing the latest advances in acrylic technology. It is manufactured from a unique acrylic resin specifically designed to provide increased tensile strength and elongation on problem roof areas.
3 PRIMERS ARS- URAPLUS PRIMER HP ARS- URAPLUS PRIMER HP is a single component, liquid applied, urethane primer. This primer provides excellent intercoat adhesion. GP PRIMER- HS GP PRIMER- HS is a rapid drying, asphalt- based primer that enhances adhesion of asphalt coatings and repair materials over asphalt, metal or concrete surfaces. AQUAPRIME AQUAPRIME is a quick drying, totally VOC compliant primer that improves the adhesion of self- adhering membranes, asphaltic coatings and repair materials to asphalt, concrete and aged metal surfaces. ARS CLEARPRIME WB (Solvent Free) ARS CLEARPRIME WB is a transparent water- based primer that improves the adhesion of a wide variety of coatings and membranes. Its transparency leads to a much neater application and cleaner jobsite. Its composition involves a chemistry which contains compounds with inherently superior adhesion characteristics. COATINGS URAPLUS MP ROOF COATING URAPLUS MP ROOF COATING is a versatile, multi- purpose aliphatic single- component, moisture- cured liquid urethane coating designed for use as a base coat or top coat, or for repair work on a variety of mature roof systems, including spray polyurethane foam, aged or cured single ply, metal, built up roofs and modified bitumen. ARS- URAPLUS BASE COAT ARS- URAPLUS BASE COAT is a versatile, multi- purpose, aromatic single- component, fire retardant, moisture- cure liquid urethane coating designed for use as a base coat or for repair work on a variety of mature roof systems, including spray polyurethane foam, single ply, metal, built up roofs, and modified bitumen. ARS- URAPLUS TOPCOAT WHITE ARS- URAPLUS TOPCOAT WHITE is a single component, moisture- cured, aromatic, polyurethane coating designed as a weather protectant coating for a wide variety of waterproofing and roof system applications including spray- applied polyurethane foam, single ply membranes, and built- up roofs. It meets the VOC content requirements for roof coatings established by the most stringent regulators. EMULSO- FLEX EMULSO- FLEX is an elastomeric, mineral- stabilized asphalt emulsion formulated with carefully selected raw materials for maximum performance and compatibility to deliver long- term service on the roof. It is manufactured using a state of the art colloid milling process to ensure a smooth, uniform consistency. EMULSO- TOP EMULSO- TOP is a non- fibered, emulsified blend of low melt point asphalt, bentonite clay and additives for superior weatherability. WEATHER- FIGHTER KV WEATHER- FIGHTER KV is a balanced blend of premium oxidized asphalt and penetrating oils, further augmented with quality non- asbestos reinforcing fillers. WEATHER- FIGHTER KV provides rejuvenating qualities to weathered asphalt BUR systems.
4 PERMAPITCH PERMAPITCH is a water- based blend of coal tar and proprietary polymer modifiers that provide a product suitable for application to membranes with slopes of 6 per foot (45%) or less. PERMAPITCH is designed to have excellent adhesion to dry, clean, primed, uncontaminated substrates and to embedded gravel. ALUMIFLECT ALUMIFLECT is a highly reflective, leafing, asphalt- based paint that provided ultraviolet light resistance and weather protection to a variety of surfaces. ALUMIFLECT is formulated with paint quality aluminum pigments for maximum reflectivity. ALUMIFLECT FIBRATED ALUMIFLECT FIBRATED is a highly reflective, leafing, asphalt- based paint that is fibrated with non- asbestos materials for strength and stability. This product provides ultraviolet light resistance and weather protection to a variety of substrates and reduces surface temperatures for energy savings and extended product performance. ALUMIFLECT FIBRATED is formulated with paint quality aluminum pigments for maximum reflectivity. ACRIWHITE ACRIWHITE is a water- based, Energy Star compliant, acrylic coating with high solids and elastomeric properties. It is a highly reflective, permanently flexible breathing membrane, allowing moisture vapor from the substrate or building interior to escape while remaining impervious to mass water penetration from the exterior. SILIPRO SILIPRO is a ready- to use, high solids, single component, solvent borne, moisture cure fluid applied silicone coating. ICE & WATER ARS ICE & WATER, TYPE GG ARS Ice & Water, Type GG is an SBS modified self- adhering membrane reinforced with non- woven fiberglass mat for extra strength and durability. ARS Ice & Water, Type GG is a highly versatile underlayment that provides superior waterproof integrity and is an excellent second wall of defense against wind driven rain and seepage due to ice damming. ARS ICE & WATER, TYPE HT ARS Ice & Water, Type HT is an SBS modified self- adhering membrane reinforced with non- woven fiberglass mat for extra strength and durability. Its non- abrasive polyester surface is excellent for use in tile and metal applications. ARS ICE & WATER, TYPE SG ARS Ice & Water, Type SG is an SBS modified self- adhering membrane reinforced with non- woven fiberglass mat for extra strength and durability. ARS Ice & Water, Type SG is a highly versatile underlayment that provides superior waterproof integrity and is an excellent second wall of defense against wind driven rain and seepage due to ice damming.
5 ADHESIVES PERMA- SET ADHESIVE PERMA- SET ADHESIVE is a high performance, rubber modified roofing adhesive that is applied directly from the container (5 gallon pail or 55 gallon drum). It is weather and water resistant and contains adhesion promoters to increase bonding strength and overall performance. This product is used as an interply adhesive as well as a surface coating to ensure roof water tightness and adhere surfacing granules, aggregate or gravel. When adhering roof plies, it penetrates the plies to create a fused, monolithic system. When compared to hot- applied materials, PERMA- SET ROOF ADHESIVE eliminates such problems as rapid cooling of molten adhesive due to wind and temperature, fumes from the heating process and the dependence on accurate kettle operation. ELASTO- SET ADHESIVE ELASTO- SET ADHESIVE is a unique SBS modified elastomeric adhesive designed to adhere asphalt and polymer modified asphalt sheet materials in reroofing and new roof applications. ELASTO- SET ADHESIVE is an innovative, economical material that can be applied by spray or notched squeegee. INSUL- BOND INSUL- BOND is a cold- applied, one- part, solvent- free, asphalt/urethane insulation adhesive. It is used to bond approved insulations to a large variety of approved substrates. It is ideal for projects where solvent odor can be a problem or when mechanical fasteners cannot be used. It is solvent free and conforms to emission regulations in all communities. ARS EPDM BONDING ADHESIVE WB ARS EPDM Bonding Adhesive WB is an acrylic latex- based adhesive with superior bonding performance. The product is white in color when wet and is clear when dry. The solids content is approximately 60%, and the overall texture is similar to latex paint. ELVALOY FLASHING ADHESIVE ELVALOY FLASHING ADHESIVE is a solvent- based, high performance contact adhesive. It contains ketone, toluene, aliphatic hydrocarbon, and xylene solvents. ARS FB ELVALOY WB BONDING ADHESIVE ARS FB ELVALOY WB BONDING ADHESIVE is a high solids, polymer modified emulsion adhesive. ARS HP ASPHALT ARS HP ASPHALT is a specially chosen asphalt refined for use as a superior waterproofing adhesive and floodcoat in roof construction. ARS HP ASPHALT creates a weather- resistant system and is processed to retain essential oils to maintain those properties necessary for long- term performance. ARS COAL TAR ARS- Coal Tar is manufactured to provide unique performance properties as a high- quality, coal tar pitch for use in the construction of built- up roof membrane assemblies. ARS- Coal Tar may be used as an interply adhesive with appropriate American Roofing Systems tar- based ply sheet, and as a surfacing floodcoat with gravel. ARS- Coal Tar complies with ASTM D 450, Type I. The molecular structure produces inherent characteristics that are resistant to water, UV and vapor penetration. In addition, its self- healing characteristics provide extra protection. ARS AP ADHESIVE AP ADHESIVE is a ready to use, SBS modified bitumen based cold adhesive that contains a bituminous binder with sticking agents and low solvent percents (complies with California VOC regulations). It is used for membrane adhesion in lieu of hot asphalt to acceptable and properly prepared low slope and horizontal substrates. This adhesive is applied by squeegee, or spray. AP ADHESIVE meets ASTM D 4479 criteria.
6 ARS THERMOTAR ARS- THERMOTAR provides unmatchable performance properties as a high- quality, coal tar pitch for use in the construction and maintenance of built- up roof membrane assembles. ARS ThermoTar may be used as an interply adhesive with appropriate tar- based ply sheets. It can also be used as a surfacing floodcoat with gravel. ARS- THERMOTAR complies with ASTM D 450, Type I The molecular structure produces inherent characteristics that are resistant to water UV degradation, vapor penetration and chemicals. In addition, its self- healing properties provide a mechanism in concert works with its inherent chemistry produces extremely long- lasting performance. ARS THERMOTAR PREMIUM ARS THERMOTAR PREMIUM is a coal tar product that has been modified with proprietary polymers to provide exceptional durability in built- up roof membrane assemblies. ARS THERMOTAR PREMIUM may be used as an interply adhesive and as a surfacing floodcoat with gravel. The inherent coal tar molecular structure of ARS THERMOTAR PREMIUM produces characteristics that result in resistance to water, UV and vapor penetration. In addition, the unique flexibility and elongation characteristics provided by the polymer modification yield improved performance in cold temperature flex, adhesion and many other key properties that contribute to long- term performance. ARS EPDM GP WATERSEAL ARS EPDM GP WATERSEAL is a black synthetic rubber based product designed specifically as a premium grade brush and roller applied contact adhesive for bonding EPDM membrane materials in single ply roofing systems. The resin reinforced rubber in this adhesive produces strong bonds that are resistant to moisture, oil, and grease. Maximum physical and chemical properties are achieved after 2-3 days from time of application. ARS EPDM SB BONDING ADHESIVE ARS EPDM SB BONDING ADHESIVE is a synthetic rubber adhesive designed especially for the installation of fully or partially adhered EPDM roof membrane systems and flashings. ARS EPDM SPLICE ADHESIVE ARS EPDM SPLICE ADHESIVE is a black, butyl rubber based product designed for splicing EPDM membranes and uncured EPDM flashings. This product has been formulated to provide fast drying, long open time and high peel strength. When cured, ARS EPDM SPLICE ADHESIVE offers good resistance to heat, cold water and moisture. ARS EPDM SPLICE ADHESIVE can be easily brushed or roller applied at high or low temperatures. ARS EPDM/TPO LOW VOC BONDING ADHESIVE EPDM/TPO Low VOC Bonding Adhesive is a high strength solvent- based contact adhesive that allows bonding of EPDM and TPO membrane to various porous and non- porous substrates. It is specially formulated using a blend of VOC exempt and nonexempt solvents to be in compliance with the state of California Clean Air Act of 1988 (updated in1997) and as further regulated by California s Air Quality Control Districts listing VOC grams per liter limitations. This product also meets the <25 gpl VOC content requirements of the OTC Model Rule for Single Ply Roofing Adhesives. ARS EPDM WB BONDING ADHESIVE ARS- EPDM WB Bonding Adhesive is an acrylic latex- based adhesive with superior bonding performance. The product is white in color when wet and is clear when dry. The solids content is approximately 60%, and the overall texture is similar to latex paint. ARS- WHITE MB ADHESIVE With the greater emphasis on reflectivity in the roofing industry, more and more white surfaced membranes are being installed. The use of black asphalt- based adhesives creates an unsightly appearance at the seams of these white products. ARS- White MB Adhesive prevents this problem as its white color does not disrupt the overall look of the finished roof and maintains reflectivity.
7 BASE/PLY SHEETS TRIFORCE ROOFING SHEET ARS- TRIFORCE Roofing Sheet is a high performance, asphalt coated, multi- purpose roof sheet. It is triple reinforced with a polyester /glass/ polyester industrial strength fabric. It is coated with an asphalt compound specifically designed for roofing applications. This coating maximizes adhesion and contributes to the total waterproofing weight of the completed roof assembly. ARS- TRIFORCE Roofing Sheet is applied without the necessity of cutting the sheet in short lengths and allowing it to relax before installation. TRIFORCE ROOFING SHEET HS ARS- TRIFORCE Roofing Sheet- HS is a high performance, asphalt coated, multi- purpose roof sheet. It is triple reinforced with a polyester /glass/ polyester industrial strength fabric. It is coated with an asphalt compound specifically designed for roofing applications. This coating maximizes adhesion and contributes to the total waterproofing weight of the completed roof assembly. ARS- TRIFORCE Roofing Sheet- HS is applied without the necessity of cutting the sheet in short lengths and allowing it to relax before installation. ARS GLASS BASE SHEET ARS Glass Base is a non- porus 28 pound base sheet, uniquely designed and constructed to be strong while remaining wrinkle resistant. This unique combination of strength and suppleness is achieved by coating a heavyweight, specially designed fiberglass mat with type IV asphalt. The asphalt coating helps maintain a uniform consistency on both sides of the sheet and eliminates pinholes. ARS MODIFIED GLASS BASE SHEET ARS MODIFIED GLASS BASE SHEET is a fiberglass mat coated with polymer modified asphalt. These polymers alter the basic physical characteristics of the asphalt, which provides enhanced weathering, aging and sealing characteristics. ARS MODIFIED GLASS BASE SHEET meets the shower test of ASTM D4869 and exceeds the tensile strength requirements of ASTM D226. ARS MOD- POLY T/T ARS MOD- POLY T/T is a 3.0 mm thick, fire- rated, polyester reinforced SBS modified bitumen sheet with polypropylene burn- off film on both top and bottom surfaces to aid in proper application. This sheet is designed to be applied using torch welded methods. ARS POLYFORCE BASE SHEET ARS POLYFORCE BASE SHEET is a uniquely designed SBS modified, asphalt- coated, polyester roofing sheet. SBS modifiers provide excellent weathering and heat stability characteristics, and are used in applications requiring the highest levels of performance. ARS POLYFORCE BASE SHEET provides excellent elongation and tensile properties, as well as superior characteristics when subjected to stress. It also provides superior tear and puncture resistance. ARS MOD BASE IV (ALSO HAVE MOD BASE VI) ARS MOD BASE IV is 90 mils (2.2 mm) thick and is composed of selected SBS modified bitumen applied onto a glass mat reinforcement with high brush sanded bottom and top surface. ARS MOD BASE IV is adhered to a properly clean, dry, and/or primed (where required) substrate by using hot asphalt or cold adhesive. Option inner ply(s) or the field cap membrane is bonded to the properly prepared, clean, dry and/or primed (where required). A self- adhesive cap sheet can also be installed when the ARS MOD BASE IV surface is properly prepared with the appropriate primer and sealant is applied to all side and end lap edges not having a bitumen bleed out.
8 ARS POLY MOD BASE ARS POLY MOD BASE is 120 mils (3 mm) thick and formulated with high quality asphalt which is modified with styrene- ethylene- butylene- styrene (SEBS) and styrene- butadiene- styrene (SBS) copolymers. This product is reinforced with a core of 180 g/m2 non- woven, high- strength polyester. This unique blend of components allows the membrane to absorb significant thermal shock and remain flexible at very low temperatures. ARS POLY MOD BASE II ARS POLY MOD BASE II is formulated with a high percentage of SBS (Styrene Butadiene Styrene) elastomeric polymers blended with specially selected asphalts, the resulting waterproofing compound has a rubber- like elasticity capable of taking on conditions of extreme roof stress. The membrane is reinforced with a heavy- duty, nonwoven, needle- punched, polyester fabric giving it superior toughness and puncture resistance, which is superior to conventional built- up roofing. The formulation and polyester reinforcement assure membrane flexibility at all temperatures, including those 0 F. ARS MOD- GLASS T/T ARS MOD- GLASS T/T is 90 mils (2.2 mm) and is composed of selected SBS modified bitumen applied onto a glass mat reinforcement with plastic film bottom and top surface. ARS MOD- GLASS T/T is adhered to a properly prepared, clean and dry substrate using heat welding. Optional inner ply(s) or the field cap membrane ply is heat welded to the ARS MOD- GLASS T/T. ARS UNIFORCE FELT UNIFORCE FELT is a non- porus 28 pound base sheet, uniquely designed and constructed to be strong while remaining wrinkle resistant. This unique combination of strength and suppleness is achieved by coating a heavyweight, specially designed fiberglass mat with type IV asphalt. The asphalt coating helps maintain a uniform consistency on both sides of the sheet and eliminates pinholes. ARS TAR GLASS I ARS TAR GLASS I is a high- strength, glass fiber felt impregnated with coal tar for maximum weatherproofing performance. It is specifically designed for use with ARS THERMO TAR and ARS THERMO TAR PREMIUM and provides the toughness of a glass felt and compatibility with hot- applied, coal tar bitumens. ARS TAR GLASS II ARS TAR GLASS II is a high- strength, glass fiber felt impregnated with coal tar for maximum weatherproofing performance. It is specifically designed for use with ARS THERMO TAR and ARS THERMO TAR PREMIUM and provides the toughness of a glass felt and compatibility with hot- applied, coal tar bitumens.
9 CAP SHEETS BLAZEBLOCK SBS BLAZEBLOCK SBS is a Class A /B fire rated over combustible & non- combustible decks, without need for protective coatings or gravel. BLAZEBLOCK SBS achieves this rating since it is manufactured with fire retardant chemicals. BLAZEBLOCK SBS offers versatility of application with hot asphalt, cold adhesive, or heat- welded application. Various reinforcement options are also available: This includes polyester, glass, and dual reinforced membranes. ARS- ENDURAPLY S160 ARS- ENDURAPLY S160 is a smooth 160 mils (4.0 mm) thick and is composed of selected SBS modified bitumen applied onto a 250 polyester reinforcement and is produced with a sanded underside and topside. The sanded base membrane ply is adhered to a properly prepared and, if necessary, primed substrate by using hot asphalt or properly selected cold adhesive. The bottom sanded surface on the applied ARS- ENDURAPLY S160 allows it to be applied either by hot mopping or cold adhesive to base plies to form a multi- ply system. ARS- ENDURAPLY S160 meets ASTM D 6164, Type IV, Grade S. ARS- ENDURAPLY SUPREME ARS- ENDURAPLY SUPREME is a granule- surfaced 160 mils (4.0 mm) thick and is composed of selected SBS modified bitumen applied onto a non- woven fiberglass composite reinforcement and is produced with a sanded underside and topside. The sanded base membrane ply is adhered to a properly prepared and, if necessary, primed substrates by using hot asphalt or properly selected cold adhesive. The sanded surface on the applied ARS- ENDURAPLY SUPREME allows for additional sheet membranes to be applied either by hot mopping, cold adhesive, or heat welding application method. ARS- ENDURAPLY SUPREME meets ASTM D 6162, Type III, Grade G. ARS- FIBERPLY G6 ARS- FIBERPLY G6 is a high performance Type VI fiberglass ply sheet designed for use in a variety of roofing systems. ARS- FiberPly G6 provides consistently higher strength with superior handling and application characteristics. ARS LASTOPROOF - HS ARS LASTOPROOF - HS is a granule surfaced roofing sheet composed of a formulated elastomeric blend of SBS and asphalt compounded with a special fire retardant additive. This blend is applied onto a woven composite fiberglass and polyester reinforcement mat for increased tensile strength. LASTOPROOF - HS has a film underside, for heat welding application, and a granulated top for service as a field cap membrane sheet. This product can be adhered to a variety of properly prepared, clean, dry and primed (where required) substrates using heat weld application methods. ARS LASTOPROOF MS FR ARS LASTOPROOF MS FR is a granule surfaced roofing sheet composed of a formulated elastomeric blend of SBS and asphalt compounded with a special fire retardant additive. This blend is applied onto 180 g/m² polyester reinforcement mat for increased tensile strength. ARS- LASTOPROOF - MS FR has a sanded underside and a granulated top for service as a field cap membrane sheet. This product can be adhered to a variety of properly prepared, clean, dry and primed (where required) substrates using various application methods. ARS REINFORCED EPDM MEMBRANE ARS REINFORCED EPDM MEMBRANE is a high performance reinforced membrane that resists tearing, impacts, punctures and normal roof traffic. The elastomeric properties of the EPDM membrane compensate for thermal shock and building movement. EPDM membranes provide excellent resistance to ozone and aging. The membrane is manufactured in accordance with the guidelines established by the RMA (Rubber Manufacturers Association) and meets or exceeds the ASTM Standard Specification D Fire retardant (FR) membranes are specially formulated to inhibit spread of flame and meet or exceed code body testing criteria for fire retardant roofing membranes.
10 EXTRAGUARD SBS EXTRAGUARD SBS minimizes buckling, wrinkling, and fish mouths associated with unmodified base/plies. EXTRAGUARD SBS is used as a base/ply, and is covered with one of our cap sheets. EXTRAGUARD SBS is available in four weights, & 60 lbs/square, to meet most job conditions. EXTRAGUARD SBS offers versatility of application with hot asphalt, cold adhesive, or mechanical fasteners. Various reinforcement options are available: This includes polyester, glass, and fiberglass scrim. EXTRAFLEX EXTRAFLEX is a highly elastic polyester- reinforced membrane. The flexibility of the product makes it ideal for flashing and single ply applications. EXTRAFLEX membranes can be applied over one layer of EXTRAGUARD SBS / EXTRAGUARD SBS base. Since only one application of asphalt/adhesive is needed, there is tremendous savings in labor and asphalt costs. EXTRAFLEX membranes are available in smooth and granulated surfacing. EXTRAFLEX offers versatility of application with hot asphalt or cold adhesive. Various reinforcement options are available: This includes polyester and dual reinforced (polyester & glass reinforced) membranes. PERMAWELD SBS PERMAWELD is an extremely flexible torch- applied SBS membrane. PERMAWELD SBS is superior to APP membranes because the asphalt is modified with Styrene Butadiene Styrene (SBS) a synthetic rubber, providing it with a rubberized property. APP membranes are manufactured by blending the asphalt with Atactic Polypropylene (APP), which is basically asphalt that has been modified with plastic. The addition of SBS to rubber makes the membrane easier to apply than other products, with better adhesion to metal and end laps. Various reinforcement options are available: This includes polyester, glass, and dual reinforced membranes. PERMAWELD SBS is available in smooth and granulated surfacing. SECURECAP SECURECAP SBS is an economical cap sheet. Used in conjunction with EXTRAGUARD or BARRIER SBS membranes. This system offers a superior alternative to BUR or APP torch membranes at a competitive price. Various reinforcement options are also available: This includes glass and fiberglass scrim. SECURECAP SBS offers versatility of application with hot asphalt, cold adhesive or heat weld application. ELECTOMOD ELECTOMOD is a unique foil- faced surface that absorbs much less heat than does a conventional roofing system, thus resulting in reduction of a building s energy consumption. In most cases, this allows the building owner to use a smaller air conditioning unit. ELECTOMOD SBS Cool White 24 has reflectivity characteristics, which exceed the initial requirements set forth by the United States Environmental Protection Agency Energy Star standard and by the Energy Efficiency Standards for Residential and Nonresidential Buildings, Title 24 of the California Code of Regulations. ELECTOMOD SBS Cool White 24 reflects 75% of solar energy away from the roof surface
Roof Systems Overview Cold Applied Built-Up Roofing Systems BURmastic Tremco s line of cold applied built-up roofing systems. BURmastic 200 Combines Tremco s expertise in asphalt blending technology with
WATERPROOFING OF REINFORCED CONCRETE FLAT ROOF 12 87 88 GOOD INDUSTRY PRACTICES 12 WATERPROOFING OF REINFORCED CONCRETE FLAT ROOF 12.1 BACKGROUND Most roofs in Singapore are constructed using reinforced
Firestone Modified Bitumen Roofing Systems DURABLE. RELIABLE. SUSTAINABLE I n t r o d u c t i o n t o M o d i Acres of Roofing. Decades of Performance. Over the past 20 years, Firestone Building Products
Fluid Applied Membrane System seamless possibilities Neptune Coatings Corporation (NCC) manufactures the WetSuit System for roofing, waterproofing and air/vapor barrier applications. In contrast to other
TOPCOAT Liquid-Applied Roofing Systems TOPCOAT System Specifications EPDM (TOPGN160) Updated: 7/14 TOPCOAT System Specifications EPDM PART 1 GENERAL 1.01 SYSTEM DESCRIPTION U.S. Only The TOPCOAT Roofing
WESTERN COOL ROOF SYSTEMS Sustainable - Energy Efficient FLUID APPLIED REINFORCED ROOF SYSTEM SPECIFICATION NO. SMAA-2P-8xE UPGRADE SMOOTH SURFACE / CAP SHEET / SINGLE PLY 2 PLY POLYESTER REINFORCED ACRYLIC
MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590
EVALUATION REPORT 2010 FLORIDA BUILDING CODE Manufacturer: Henry Company Report Issued February 20, 2013 999 North Sepulveda Blvd., Suite 800 El Segundo, CA 90245 (800) 486-1278 Manufacturing Plants: Quality
Building Owners Guide to a Duro-Last System Table of Contents Section 1: Introduction to Duro-Last Roofing Systems Section 2: Benefits of a Duro-Last Roofing System Section 3: Comparing a Duro-Last Roof
1320 / Talent Community Center 073113-1 ASPHALT SHINGLES PART 1 GENERAL 1.01 SECTION INCLUDES A. Asphalt shingle roofing. B. SBS roof membrane. SECTION 073113 ASPHALT SHINGLES C. Flexible sheet membranes
ROOFING SYSTEMS Purpose Examples 1. Shingle roof system 2. Metal roof with blanket insulation 3. Metal roof with rigid insulation 4. Built-up asphalt roof system 5. Single-ply roof system 6. Modified Bitumen
Peel & Seal Self-Stick Roofing Solutions Ideal for Low Slope Applications Waterproof and Weatherproof Energy Efficient Tough and Durable Versatile, Effective Sealing Around Protrusions Perfect for Vents,
LAMA has developed over the years a wide range of products that can be used in the waterproofing and damp-proofing of roofs, decks, car parkings, walls, foundations, basements, roads, etc. In this catalogue,
Colorado State University Durrell Center Roof Repair SPECIFICATION: POLYURETHANE FOAM ROOFING l.0 GENERAL REQUIREMENTS The successful application of a polyurethane foam roofing system is dependent upon
BSW HIGH PERFORMANCE PRE-APPLIED SYSTEM FOR BLIND SIDE & BELOW GRADE WATERPROOFING APPLICATIONS BSW is a fully reinforced Pre-Applied system membrane designed for horizontal and vertical external blind-side
Maintenance & repair Solutions low-slope ROOFING We ve got what you need in the sizes you need them and the options to match the results that building owners want Seal-fast Temporary roof sealer Now you
Roofing Systems There are many different systems, each with it's own special requirements and benefits. Browse through all the options below. BUR (Built-Up Roofing) Built-Up-Roofing, BUR is a roof that
07560 BUR BUILT-UP ROOF COATING SMOOTH and GRANULE SURFACE SPECIFICATION PART 1: GENERAL 1.01 SCOPE: To extend the useful service life of the aged or new asphalt built-up roof system and to reduce cooling
Advances in An American Institute of Architects (AIA) Continuing Education Program Membrane Roofing Credit for this course is 1 AIA HSW CE Hour Advances in Membrane Roofing Course Sponsor POLYGLASS USA,
Peel & Seal Self-Stick Roofing Solutions Ideal for Low Slope Applications Waterproof and Weatherproof Energy Efficient Tough and Durable Versatile, Effective Sealing Around Protrusions Perfect for Vents,
. FACE OF WALL.. STUD CONSTRUCTION WITH FIBERGLASS BATT INSULATION AND FIBERGLASS FACED EXTERIOR GYPSUM SHEATHING WITH JOINTS SEALED USING -PART POLYURETHANE PRIOR TO INSTALLING FLUID APPLIED WEATHER RESISTANT
EXPANDED POLYSTYRENE FOR COMMERCIAL BUILDING APPLICATIONS www.falconfoam.com Commercial Building Ap Expanded Polystyrene Insulation Falcon Foam leads the commercial building industry with products that
Extreme Sealing Tape Technical Data May, 2013 Product Description 3M Extreme Sealing Tape is a family of single coated, pressure sensitive adhesive tapes designed for difficult sealing applications. The
Extreme Sealing Tape Technical Data January, 2013 Product Description 3M Extreme Sealing Tape is a family of single coated, pressure sensitive adhesive tapes designed for difficult sealing applications.
RECOATING AND RENEWING SPF ROOFING SYSTEMS Procedures, Regional Differences and type of coating systems Bruce Schenke Premium Spray Products REASONS TO RECOAT/RENEW Add a new coating layer to renew the
Quality You Can Trust Since 1886... From North America s Largest Roofing Manufacturer Leak Buster Repair & Maintenance Products Quality You Can Trust Since 1886...From North America s Largest Roofing Manufacturer
Seamless Waterproofing Systems Pitched/Corrugated Roofs Liquid Rubber Instant Set is the ideal solution for pitched roof waterproofing providing a seamless fully bonded finish. RapidRoof is suited to smaller
MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590
DESCRIPTION Construct adhered membrane roofing system, roof insulation, and vapor retarder in accordance with these specifications. MATERIALS: General: Provide installed roofing membrane and base flashings
PAGE: 1 of 6 PRINT DATE: 16/09/2004 BLACK JACK ALL WEATHER ROOF COATING DESCRIPTION BLACK JACK ALL WEATHER ROOF COATING is a solvent based, full bodied black brushable compound with added fibres for reinforcement.
CHAPTER 6 ASPHALT ROLL ROOFING Section I. DESCRIPTION AND GENERAL DISCUSSION 6.1.1 General 6.1.3 Mineral-Surfaced Asphalt roll roofing is roofing in sheet form Mineral-surfaced roll roofing is composed
MANUAL OF CONTRACT DOCUMENTS FOR ROAD WORKS VOLUME 1 SPECIFICATION FOR ROAD WORKS SERIES 2000 WATERPROOFING FOR CONCRETE STRUCTURES Contents Clause Title Page 2001 General 2 2002 Protection of Bridge Deck
Roofing Systems New Applications / Re-Roofing / Maintenance New Roof Installation In terms of the design and installation of an original roofing system (in conjunction with the construction of a new building),
SBS-Modified Bitumen Roof Systems High performance systems from the developers of SBS-modified bitumen. Siplast s Paradiene 20/30 was selected for the Library of Congress in Washington D.C. Seven hundred
FAST FACTS ADVANTAGES OF MULTI PLY BUILT-UP ROOFING Roofing Manufacturers Association Why is a built-up roof considered a multi-ply roof? ARMA defines a built-up roofing system as a roof where multiple
AC TOPSEAL SELF-ADHERED, GRANULAR SURFACED, SINGLE PLY, LOW SLOPE ROLLED ROOFING 3 X 33.3 = 100 SQ. FT. 10 YEAR MATERIAL LIMITED WARRANTY For Use on Porches / Sheds / Utility Buildings / Accessory Buildings
Table of Contents Section 1: Most Common Types of Flat Roofing Section 2: Better Understand Your Flat Roof Section 3: Flat Roofing Cost in 2015: Four Factors that Dictate Section 4: Planning A Flat Roofing
HEB 38 BLANCO AND WEST AVENUE FLUID APPLIED EPDM RUBBER ROOF RECOVERY SYSTEM APPLICATION David Marut TEST CASE REPORT July 1, 2014 Case Study Pro Guard EPDM Super Coat Liquid Rubber Membrane Roof System
SECTION 230713- ALUMAGUARD ENGINEER SPECIFICATION DIVISION 23 HEATING, COOLING, AIR CONDITIONING AND VENTILATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract,
Spray Foam Insulation and Roofing Systems Accelerate Your Performance SWD Urethane Mesa, Arizona 800-828-1394 swdurethane.com Celebrating 40 Years of Foam Quik-Shield brand is owned and operated by SWD
www.epdmroofs.org COMPARATIVE PERFORMANCE OF EPDM RUBBER ROOFING MEMBRANE AS PROTECTION AGAINST HAIL DAMAGE By Ric Vitiello President Forensic Roof Consulting and Hail Damage Assessment Training www.benchmark-services.com
Roof Restoration System For building owners, property management firms and facility managers seamless possibilities Extending your roof life Think of your existing older roof custom fit with a seamless,
Roofing systems Our Promise Through ongoing interchange of experiences with contractors, Mule-Hide keeps on top of the latest roofing requirements and solutions Trusted in roofing since 1906, Mule-Hide
3 Marine Adhesives and Sealants For Demanding Marine Environments Providing secure bonds, in the water or out. Almost no environment is harsher than the beating sun and pounding waves of the open water.
Extreme Sealing Tape Technical Data October, 2011 Product Description 3M Extreme Sealing Tape is a family of single coated, pressure sensitive adhesive tapes designed for difficult sealing applications.
Alberta Allied Roofing Association Asphalt Shingle Application Requirements Section 1 Roof Decks 1.1 General Asphalt Shingles are not permitted to be installed directly over rigid insulation. When Asphalt
High Performance PSA in Sheet Membrane in Water Protection Xia Cao, Senior R&D Chemist, W. R. Grace, Cambridge MA 02140 Jyoti Seth, Strategic Program Leader, W. R. Grace, Cambridge MA 02140 Concrete is
Chapter 3 Roof Systemspecific Code Requirements In this section, code language containing requirements that pertain to specific roof systems is quoted. The roof systems specifically identified in IBC 2009
August 2016 1 Waterproofing Showers and Bathrooms Guide The purpose of this guide is to provide guidance on how a shower area or wet room can be successfully waterproofed and tiled with the products available
GOOD ROOFING PRACTICE STEEP-SLOPE RE-ROOFING ASPHALT SHINGLE ROOFING 1:3 (4/12) AND GREATER 1 DECK Revised January 6, 2011 1.1 General a) Application of asphalt shingles directly over rigid insulations
C COMMERCIAL & LOW SLOPED ROOF SPECIALISTS We are equipped to handle the largest of your commercial roof needs. Whether storm damage or simply needing a new commercial roof due to age, Cobalt allows you
Demolition/Removal of Work 4-ply built up roofing to the insulation (smooth cap sheet) Smooth cap sheet - 0-10 SQ $ 63.00 Smooth cap sheet - 11-50 SQ $ 63.00 Smooth cap sheet - 51-100 SQ $ 35.00 Smooth
Th-550 Roof Guard / Silicone modified Water-Borne matt coating, based on Elastomeric Acrylic Polyurethane emulsion and modified by silicone resin for roofs. All types of exterior mineral facades (Masonry,
September 3, 2009 Ric Boyd, Public Works Director Ketchikan Gateway Borough 344 Front St. Ketchikan, AK 99901 RE: Ketchikan Gateway Borough Gateway Recreation Center Roof Observations and Intrusive Inspections
Specifying Below Grade Waterproofing The Construction Specifier October 2005 Waterproofing is the treatment of a structure s surface to prevent the passage of water under hydrostatic head or standing water
Construction Sika For Sealing and Waterproofing Construction Gaps in Building Façades Waterproof and Airtight Flexible Seal Controlled Vapour Diffusion Bonds to any Building Substrate Prevents Interstitial
A w a p l a n S B S - m o d i f i e d r o l l r o o f i n g Mop it. Stick it. Spread it. Same proven performance. Now with more ways than ever to apply it. 1 inch 1.5 inch However you apply products, count
Game-Changing Application System Making Professional Coating Results A Reality Hillyard Concrete Defense changes the way coatings are applied - delivering professional results without the cost of professional
SEAMING USING SEAM TAPE SEAMS The membrane should be positioned so that the width of the seam is 3. Remove excess chalk from a chalk line by snapping the line into the air and then chalk a line one-quarter
V E R S I C O R O O F I N G S Y S T E M S PVC ROOFING SYSTEMS BUILDING SOLUTIONS A SINGLE SOURCE FOR SINGLE-PLY ROOFING Versico, PO Box 1289, Carlisle, PA 17013 Tel: 800.992.7663 Fax: 717.960.4036 Web:
SECTION 07 61 13 STANDING SEAM METAL ROOFING PART 1 GENERAL 1.01 SCOPE OF WORK A. The Work shall include all labor, materials, equipment and supervision required to complete the work of the above referenced
WindowWrap Window & Door Flashing System Superior Quality Eliminates Leaks and Drafts Around Windows and Doors Improves Energy Efficiency Reduces Noise Transmission Rugged and Reliable Helps Reduce Expensive
A quick reference guide to Effective Waterproofing Identifying Damp The term damp strikes fear into the hearts of most homeowners. Left untreated, a small, easily repairable problem can become much larger
FEFPA 2015 SUMMER CONFERENCE Energy Effectiveness through Roof Coatings and Solar Welcome Danny G. Daniel Stokes, CSI, CDT, RCI, CPRC Vice President Advanced Roofing Inc. About Danny Stokes Vide President
When choosing a secondary containment system it must be chosen based on its ability to withstand long term contact with the natural elements (weather), whatever the tanks hold (unrefined oil, fuels, acids,
ROOFING TECHNOLOGY Arch 173: Building Construction 2 Roof and membrane failures are the most often litigated parts of a building good detailing is paramount never use materials or systems that have not
Acrylic Coatings: The Perfect Stucco Finish By Larry Miller and Joe Miller Whether a stucco surface is new or old, there are many different finish coatings in today s marketplace that are supposedly right
THE EFFECT OF REFLECTIVE ROOF COATINGS ON THE DURABILITY OF ROOF SYSTEMS Joseph W. Mellott II and Donald C. Portfolio ROOF COATING MANUFACTURERS ASSOCIATION International Roofing Expo TU-03 Technical March
CI/SfB Oct 12 (47) Ln Uniclass L524 FLAME-FREE, FELT SYSTEM, INSTALLED USING HOT AIR, TOTALLY ELIMINATING FIRE RISK AND PROVIDING A BITUMEN ALTERNATIVE TO SINGLE PLY Bailey Flame-free felt roofing Bailey
Guide to Green Roofing Facility Management Journal November/December 2009 A properly installed green roof allows building owners and managers to achieve longterm cost savings and counter climate change
Your consent to our cookies if you continue to use this website.