Metasys Integrator Notifier AFP-200 Fire Panel Application

Transcription

1 Metasys Connectivity Technical Manual Metasys Integrator Section Application Note Issue Date 0900 APPLICATION NOTE Metasys Integrator Notifier AFP-200 Fire Panel Application Introduction Page *3 Application Details *3 Component Requirements *5 Vendor Contact Information *6 Design Considerations *6 Cable Connections 9 Cable Pinouts *9 Connecting the Cable *9 Metasys Integrator Setup *11 Point Mapping Tables 13 Detector Points *13 Module Points *13 Bell/System Trouble Points *14 Metasys Network Setup *17 Mapping to a CS Object *17 Custom Integration *19 *Indicates those sections where changes have occurred since the last printing Johnson Controls, Inc. 1 Code No. LIT

2 2 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

3 Introduction This document explains the Metasys Integrator Notifier AFP-200 Fire Alarm Panel application. Use this document with the Metasys Integrator technical bulletins that provide information on installing and commissioning the Metasys Integrator unit. For information on the AFP-200 Fire Panel, see the Notifier documentation. Please note that this application will also work with the Johnson Controls IFC-200 Fire Panel. Note: If you are using a Universal Packaging Module (UPM), you must install the Metasys Integrator 300 Series in a two high enclosure (EN-EWC25-0) rather than a one high enclosure (EN-EWC13-0) as shown in the figures in this application note. Application Details The Metasys Integrator unit allows the Notifier AFP-200 Fire Alarm Panel to communicate with the Metasys and Metasys Companion Networks. Once a Notifier AFP-200 Fire Panel is connected to a Metasys or Companion Network via the Metasys Integrator unit, its data is available to the full complement of Metasys Building Automation System (BAS) features, including Change-of-State (COS) monitoring, secondary reporting, alarm and trouble notification, trend, and totalization. Each Metasys Integrator vendor port can connect to one AFP-200 Fire Panel. The AFP-200 Fire Panel has a single Signaling Line Circuit (SLC) that supports up to 99 detectors and 99 modules, plus four Notification Appliance Circuits (NACs) designated Bell Circuits on the panel. When the AFP-200 Fire Panel is reset, all Binary Input () points are reset to an open or 0 value and any trouble status is cleared.! CAUTION: The Metasys Integrator unit is not Underwriters Laboratories (UL) 864 Listed as a fire alarm control unit. It is designed to provide only secondary ancillary monitoring, while the AFP-200 Fire Control Panel provides UL 864 Listed notification and control functions. Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 3

4 N1LAN Standard NCU RS-232 AFP-200 Fire Panel Metasys Integrator UNT Note: If you are using a UPM, you must install the Metasys Integrator 300 Series in a two high enclosure (EN-EWC25-0) rather than a one high enclosure (EN-EWC13-0) as shown in the figures in this application note. afp1 Figure 1: AFP-200 Fire Panel and Metasys Integration Panel Unit Workstation Metasys Integrator RS-232 (50 ft maximum) AFP-200 Fire Panel UNT N2 Bus Note: A PC version and converter may be substituted for the Panel unit. afp200comp Note: If you are using a UPM, you must install the Metasys Integrator 300 Series in a two high enclosure (EN-EWC25-0) rather than a one high enclosure (EN-EWC13-0) as shown in the figures in this application note. Figure 2: AFP-200 Fire Panel and Metasys Companion Integration 4 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

5 Component Requirements Metasys Release Requirements Metasys Companion Release Requirements To integrate the AFP-200 Fire Panel, you need the following: properly installed AFP-200 Fire Panel with firmware Version 2.4 RS-232 cable (for connecting the AFP-200 Fire Panel s RS-232 port to the Metasys Integrator unit) Metasys Integrator unit B&B Optical Isolator, Model RS232 OP4 N2 Bus (for connecting the Metasys Integrator unit to the Metasys Network Control Module [NCM] or Companion Network) portable Personal Computer (PC) for downloading vendor communication tables (.VCT files) and network setup information into the Metasys Integrator unit, and for running diagnostics cable for connecting the portable PC to the Metasys Integrator unit cables for connecting AFP-200 Fire Panel to the Metasys Integrator unit (see pin requirements in the Cable Connections section of this document) standard duplex 120 VAC outlet, required within one foot of the B&B Optical Isolator, Model RS232 OP4 to power this device. This device has two plug-in power supply transformers. This document describes the RS-232 cable and vendor communication tables. Notifier documentation describes their equipment. The remaining components are described in the Metasys Integrator technical bulletins. To integrate the AFP-200 panel into the Metasys Network, you need: Metasys Operator Workstation (OWS) software Release 7.0 or higher Metasys Integrator software/firmware Release 9.0 or higher To integrate the AFP-200 panel into the Metasys Companion Network, you need: Metasys Companion Release 6.0 or higher Metasys Integrator software/firmware Release 9.0 or higher Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 5

6 Vendor Component Requirements Vendor Contact Information Integration between the Metasys Integrator unit and Notifier AFP-200 Fire Panel application has been tested with Notifier AFP-200 Firmware Release Version 2.4 and B&B Optical Isolator Model RD232 OP4. B&B Optical Isolator Model RS232 OP4 is required between AFP-200 panel RS-232 port and Metasys Integrator vendor port to eliminate the ground fault. Changes to this equipment or integration of either Notifier or B&B products not discussed in this document require additional software development and testing by Johnson Controls Systems Products. For information on integrating other products, refer to the Custom Integration section of this application note. Notifier One Fire-Lite Place Northford, CT Phone: (203) FAX: (203) B&B Electronics Company 707 Dayton Road P. O. Box 1040 Ottawa, IL Phone: (815) FAX: (815) Design Considerations When integrating the AFP-200 Fire Panel, consider the following: Make sure that the AFP-200 Fire Panel is set up and running properly with Version 2.4 firmware before integrating with a Metasys or Companion system. This includes configuring the AFP-200 Fire Panel s RS-232 printer port in remote terminal mode. (The Notifier representative is responsible for the configuration and operation of Notifier equipment.) The Metasys Integrator unit is not UL 864 Listed as a fire alarm control unit. It is designed to provide secondary ancillary monitoring only, while the AFP-200 Fire Panel provides notification and control functions. When the AFP-200 Fire Panel is reset, all points are set to open state and the trouble status is reset. The AFP-200 Fire Panel must be reset to clear alarms. RS-232 cable distance between the Metasys Integrator unit and the AFP-200 Fire Panel cannot exceed 50 feet. The trouble status is cleared when a device reports a normal or off state. 6 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

7 Programming at the AFP-200 Fire Panel will cause the Notifier AFP-200 Fire Panel to go offline. Also, continuous pressing of the panel keys (e.g., Ack/Step) may cause the AFP-200 Fire Panel to go offline at the Metasys Integrator unit. The AFP-200 Fire Panel, when used alone without the Metasys Integrator unit, has a feature that scrolls through trouble messages when multiple messages exist on the system. This feature is not present when the Metasys Integrator unit is connected to the AFP-200 Fire Panel. If multiple messages exist on the system, the Ack/Step key must be pressed to view each individual message.! WARNING: Some change-of-state messages may be missed while running the Diagnostic Analyzer on the Metasys Integrator commissioning PC. Do not run the Metasys Integrator Diagnostic Analyzer after commissioning is complete. Disconnect the Metasys Integrator unit from the AFP-200 printer port while programming the Fire Panel, then reset the AFP-200 panel after reconnecting the Metasys Integrator unit. Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 7

8 8 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

9 Cable Connections Cable Pinouts Use the following cable pinouts for the RS-232 connection between the Metasys Integrator unit and the AFP-200 Fire Panel. You must connect the male end of the converter to the Metasys Integrator unit. Vendor Port A or B of Metasys Integrator DB-9 Female Signal RD TD GND Pin VDC/ 120 VAC Male (25 Pin) Duplex Outlet Optical Isolator Model 2320 P4 (50 ft maximum) Female (25 Pin) RS-232 Printer Port on APF-200 (TB4) TX RX RF afp3 Figure 3: Cable Pinouts Connecting the Cable Connect the female end of RS-232 cable to either Vendor Port A or Vendor Port B on the Metasys Integrator unit. Connect the other open end (no connector) of the cable to terminal TB4 of the panel as specified in AFP-200 Fire Panel installation documentation. Metasys Integrator AFP-200 Fire Panel Vendor Port A or B Optical Isolator RS-232 Printer Terminal Port TBA (EIA-232) afp4 Figure 4: Port-to-Port Connection Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 9

10 10 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

11 Metasys Integrator Setup To set up the Metasys Integrator unit, use a portable PC connected to Metasys Integrator Terminal Port. Metasys Integrator setup involves: downloading the correct vendor communication tab (.VCT files) setting up the ports setting up the network addressing The following table provides information specific to the AFP-200 Fire Panel application. For detailed procedures, see the Metasys Integrator technical bulletins. Table 1: Metasys Integrator Setup for AFP-200 Fire Panel Vendor Communication Table (.VCT File) Detector Points Module Points Bell (NAC) and System Trouble Points Port Setup Baud Rate 2400 Word Length 7 Stop Bit 1 Parity Interface Network Setup Vendor Address Detectors Modules Bell (NAC) and System Trouble Points Timeout Value Poll Delay Retries 5 Approximate Scan Time (for an N2 address) Detectors Modules Bell (NAC) and System Trouble Points Time to Receive Alarm/Trouble (after the message generated at the panel) * Be sure to use uppercase characters. IFC2_DET.VCT IFC2_MOD.VCT IFC2_BEL.VCT Even RS-232 D* M* B* 3000 ms 0 ms 60 seconds 60 seconds 10 seconds 2 seconds Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 11

12 12 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

13 Point Mapping Tables The following tables show the points available for mapping on the AFP-200 Fire Panel: Detector Points points for each sensor have corresponding Binary Data (BD) points, which are used to map the pre-alarm status of the sensor. These points also indicate the trouble status of the detector. Table 2: Detector Points NPT 1 NPA 2 Description Value Mapped 1-99 Detector SLC Address-LPA 1-Alarm BD 1-99 Pre-alarm status of detector at LPA 1-Alarm 1 Network Point Type 2 Network Point Address When any detector point goes in or out of trouble, its value remains as it was before the trouble occurred. Module Points points also indicate the trouble status. These points also indicate the trouble status of the module. Table 3: Module Points NPT 1 NPA 2 Description Value Mapped 1-99 Module SLC Address-LPA 1-Alarm (Monitor Modules) 0-Off, 1-On (Control Modules) 1 Network Point Type 2 Network Point Address Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 13

14 Bell/System Trouble Points When any system trouble occurs, you must reset the IFC-200 Fire Panel manually after clearing the trouble. Table 4 is a list of all the bell circuits and system trouble status points. Table 4: Bell/System Trouble Points NPT 1 NPA 2 Description Value Mapped Network Point Type 2 Network Point Address Bell Circuit 1 Bell Circuit 2 Bell Circuit 3 Bell Circuit 4 Ground Fault AC Fail Battery Style 6 Option Module Term. Supervisory Annunciator 1 No Answer Annunciator 1 Trouble Annunciator 2 No Answer Annunciator 2 Trouble EPROM Error Internal RAM Error External RAM Error Program Corrupted No Device Installed AVPS. Trouble 0-Off, 0-Off, 0-Off, 0-Off, 1-On 1-On 1-On 1-On Note: All system trouble points remain unreliable once a device goes offline/online, until the panel is reset using the system-reset button. Individual points report online when a trouble status is reported for that point. 14 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

15 Getting Point Summary Information from AFP-200 Fire Panel to Map Points with the Metasys Network The commissioning person should have the details of point summary at the time of commissioning. If they are not available, collect the status summary from the panel using the following steps: 1. Disconnect the Metasys Integrator unit from the AFP-200 Fire Panel. 2. Connect a serial printer at printer port (the same serial port which is used for Metasys Integrator interface). 3. Press the Enter key at the panel. 4. Select 2 - read status. 5. To print all points, press 1 (print points), then Enter. A summary will be printed for all programmed points with their current status. The last three characters in each line of the message are the actual point SLC address. (For example: D01 is detector at SLC address 01, which is -1 in vendor table file IFC2_DET.VCT. M01 is module at SLC address 01, which is -1 in vendor table file IFC2_MOD.VCT. B01 is Bell Circuit 1, which is -1 in vendor table file IFC2_BEL.VCT.) See Table 2 for detector points, see Table 3 for module points, and see Table 4 for bell/system trouble points. Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 15

16 16 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

17 Metasys Network Setup Metasys Network setup is described in the Metasys Integrator technical bulletins in the Metasys Connectivity Technical Manual (FAN 629.5). This section contains details specific to the AFP-200 Fire Panel. We recommend that all points that report an alarm or trouble status be directly mapped to objects. Mapping to a CS Object Table 5: Software Model and CS Object Definition Application AFP-200 Detector SLC AFP-200 Module SLC AFP-200 Bell (NAC) and System Trouble Points Software Model (on Tables and Models CD-ROM) IF2_DLOP.DDL IF2_MLOP.DDL IF2_SYST.DDL Display Attributes (recommended) 1 Status of Detector 1 NI1 Status of Module 1 17 Network Fail NT Command Attributes 1 Status of Detector 1 1 Status of Module 1 17 Network Fail Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 17

18 18 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application

19 Custom Integration For information on integrating products which are not discussed in this document, first refer to the Metasys Compatible Global Catalog, an online list of released Connectivity products. If this list does not provide the information you require, consider using the System Integration Project Data Sheet to request a custom contract from the System Integration Team. Both the Metasys Compatible Global Catalog and the System Integration Project Data Sheet can be accessed from The Advisor by performing the following steps: 1. Click on the Systems Products button located on the left side of The Advisor home page. 2. Click on the Product Literature link. 3. Click on the Manuals-FANS link. 4. Click on the Metasys Connectivity Sales Resource Manual link. 5. Find the System Integration Project Data Sheet link in the Table of Contents. Click on this link to view an online copy of the System Integration Project Data Sheet, or click on the Metasys Compatible Global Catalog link below it to view a list of released Connectivity products. The System Integration Project Data Sheet (LIT ) can also be found in the Metasys Connectivity Sales Resource Manual (FAN 629). If you need further assistance, contact the Johnson Controls Field Support Center. Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application 19

20 Notes Controls Group FAN E. Michigan Street Metasys Connectivity Technical Manual P.O. Box 423 Metasys Integrator Release 9.0 Milwaukee, WI Printed in U.S.A. 20 Metasys Integrator Metasys Integrator Notifier AFP-200 Fire Panel Application