IntesisBox KNX Modbus RTU master
|
|
- Opal Preston
- 2 years ago
- Views:
Transcription
1 IntesisBox KNX RTU master Gateway for integration of RTU devices into KNX control systems. Integrate RTU devices (Chillers, Roof Tops, electricity meters, heating floors, heat pumps, PLCs ) into KNX control systems. KNX EIB Bus IntesisBox RS485 (can be also RS232 for single connection) RTU LinkBoxEIB Configuration Software RS232 Only needed for configuration IntesisBox acts as a RTU master device in its interface, reading/writing points of the device(s), and offering this point's values through its KNX interface. IntesisBox acts in the KNX side as one more device of the KNX system. IntesisBox's KNX EIB interface connects directly to the EIB bus and is opto-isolated from the rest of the internal electronics The interface of IntesisBox reads continuously by polling the devices/registers configured. If a non response of the is detected, the corresponding virtual signal inside IntesisBox will be activated indicating communication error with the device. All the updated readings of the registers are maintained in IntesisBox memory for immediate interaction with KNX when needed. Each register of the device is associated to a KNX group address. All the registers of the different s are accessible through KNX group addresses. When a change in any register/ occurs, a write egram is sent to the KNX bus, to the associated KNX group address. This is configurable individually per point. IntesisBox KNX series are configured using LinkBoxEIB, a software tool for windows TM which is supplied along with the purchase of IntesisBox with no additional cost. With the standard installation of LinkBoxEIB, a Demo project for integration of devices is also installed, using this demo project makes the engineering needed for this integration easy and quick. 1 / 9
2 IntesisBox capacity Element 100 version Type of devices A version B version Notes Those supporting RTU protocol. Communication over RS485 network (2-Wire) or RS232 point to point. Points Maximum number of points that can be defined into IntesisBox. devices Maximum number of devices allowed by IntesisBox. Virtual signals 1 per device 1 per device 1 per device 1 communication error signal per device defined. All available from KNX. There are three different versions of IntesisBox - KNX RTU master with different capacity every one of them: Version with capacity of 100 points and up to 254 devices. Ref. IBOX-KNX-MBRTU-100. Version with capacity of 500 points and up to 254 devices. Ref. IBOX-KNX-MBRTU-A. Version with capacity of 3000 points and up to 254 devices. Ref. IBOX-KNX-MBRTU-B. 2 / 9
3 Sample applications Integration of any RTU device into KNX control systems. KNX EIB Bus IntesisBox RS485 (can be also RS232 for single connection) RTU KNX control system: Typical devices: Building Automation. Home Automation. Chillers. Heaters. Air conditioners. Thermostats. Fan coil controllers. Room controllers. Power meters. Energy meters. Building Management Systems (BMS). Programmable Logic Controllers (PLC). Other protocol based systems available using IntesisBox Server series gateways.... KNX Full monitoring and control s System monitoring / controlling System under monitoring / control 3 / 9
4 Typical application Integration of Electricity Meters with RTU port on RS485 into KNX control systems. KNX / EIB IntesisBox KNX - RTU master RTU (RS485) 4 / 9
5 KNX interface of IntesisBox KNX/EIB interface Bus coupler Configuration parameters Interactivity with KNX/EIB system Points Configuration parameters per point Internal KNX TP1 (EIB) opto-isolated bus coupler unit for direct connection to EIB bus. Connector: 2 poles plug-in screw terminal block. Physical address. The points can be read from KNX. Configurable individually per point. The points can be written from KNX. Configurable individually per point. A write request can be sent to KNX following a change in the point s value. Configurable individually per point. The point value can be updated with a read request sent to KNX when IntesisBox starts up or after a bus reset detection. Configurable individually per point. Multiple KNX group addresses can actuate on the same IntesisBox s point. Generic fields. Point description. Useful to identify the point s location into the system. Active (Yes/No). Useful to deactivate points maintaining the configuration for later use. KNX/EIB related fields. Group address (in format P/I/S or P/S). Is the sending group address. Listening addresses (in format P/I/S or P/S separated by comma). The gateway will listen for write requests for these listening addresses, when received then it will act as if they where for the main group address defined. This is very useful to translate actions to the system coming from different KNX commands, for example from an individual start/stop button and also from a general start/stop button. Up to 1000 listening addresses can be defined in total. Up to 255 listening addresses can be defined per point. R. Specifies if the point accepts read requests from KNX. W. Specifies if the point accepts write requests from KNX. T. Specifies if a write request will be sent to KNX when the point s value changes. U. Specifies if the point s value must be updated with a read request sent to KNX when the gateway starts up or after a bus reset detection. If U is specified in this field, the read request will be of the main group address. If U2 is specified in this field, the read request will be of the first listening address defined. EIS (Datapoint). See EIS supported below. The configuration of this part must be done in co-operation with the engineer in charge of setting up the whole KNX system. Some of the data to introduce in this part must be supplied by the KNX engineer. KNX EIS (Datapoints) supported Switching (1 bit). Dimming (4 bits). Float (16 bits). Scaling (8 bits). Drive control (1 bit). Priority (2 bits). Float IEEE (32 bits). Counter (8 bits). Counter (16 bits). Counter (32 bits). ASCII char (8 bits). 5 / 9
6 interface of IntesisBox interface Device type modes supported RTU configuration parameters Interactivity with system Points Configuration parameters per point function codes supported data coding formats supported Master. RTU RS232 or RS485. RS232 or RS485. Baud rate. Data bits. Parity. Slave number per each device defined. Read: Continuous polling of devices and points defined. Updated values are available from KNX. Polling Timeout and Inter-frame Timeout can be configured in the interface. Write: Whenever a point s value is changed from KNX, the new value received is written into the device/register related. related fields. Device number (from the predefined devices list). register address into the device. Bit inside the register (optional). IntesisBox allows bit decoding from generic 16 bits input/holding registers. Bit coding into 16 bit input/holding registers is used for some devices to encode digital values into this type of registers, being these registers accessible using function codes 3 and 4 (read holding/input registers). function code. See function codes supported below. data coding format. See data coding formats supported below. This information must be extracted from the technical documentation of the devices to use. For each point, one of the following function codes can be used: 1- Read coils. 2- Read discrete inputs. 3- Read holding registers. 4- Read input registers. 5- Write single coil. 6- Write single register. 15- Write multiple coils. 16- Write multiple registers. For each point, one of the following data coding formats can be used: 1 bit. 16 bits unsigned. 16 bits signed. 16 bits signed (two s complement). 32 bits unsigned. 32 bits signed. 32 bits signed (two s complement). 32 bits IEEE. 32 bits IEEE inverted. Bit coded into 16 bits register. And many more which are device specific. 6 / 9
7 Configuration tool LinkBoxEIB Visual engineering tool, easy of use, for IntesisBox s configuration and monitoring compatible with Microsoft Windows operating systems, supplied with the purchase of IntesisBox with no additional cost. Multi-window tool allowing to monitor simultaneously the communication activity with both protocols (systems) and the real time values for all the points allowing to modify any value (very useful for test purposes), console window showing debug and operation status messages, and configuration windows to configure all the IntesisBox s parameters and points. Points configuration in plain text files (tab separated) for easy and quick configuration using Microsoft Excel (very useful in projects with a lot of points). Allows configuring the IntesisBox s parameters and points while in off-line, this is, not connected to the gateway. You can configure/modify the IntesisBox's parameters comfortably in the office and later download the configuration to the IntesisBox in the field. Connection to the IntesisBox for download the configuration and monitoring by using a serial COM port of the PC (serial cable also supplied). Allows configuring all the external protocols available for IntesisBox KNX series. Upgrades for this software tool available free of charge whenever a new protocol is added to the IntesisBox KNX series. Multi-project tool allowing to have in the engineer s PC the configuration for all the sites where different IntesisBox KNX series gateways have been installed. Multi-language tool, all the language-dependent strings are in a plain text file (tab separated) for easy modification or addition of new languages. A list of system commands is available to send to the IntesisBox, for debugging and adjust purposes (Reset, Date/time consultation/adjust, Firmware version request ). 7 / 9
8 Mechanical & Electrical characteristics Enclosure Plastic, type PC (UL 94 V-0). Dimensions: 107mm x 105mm x 58mm. Colour Light Grey. RAL Power Terminal wiring (for power supply and low-voltage signals) Mounting RTU ports KNX port LED indicators 9 to 30Vdc +/-10%, Max.: 125mA. 24Vac +/-10% 50-60Hz, Max.: 127mA Must use a NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply. Plug-in terminal block for power connection (2 poles). Per terminal: solid wires or stranded wires (twisted or with ferrule) 1 core: 0.5mm 2 2.5mm 2 2 cores: 0.5mm 2 1.5mm 2 3 cores: not permitted Wall. DIN rail EN60715 TH35. 1 x EIA485. Plug-in screw terminal block (2 poles). SELV 1 x EIA232. DB9 male connector (DTE). SELV 1 x KNX TP1 (EIB) port opto-isolated. Plug-in terminal bloc (2 poles). TNV-1 1 x Power. 2 x KNX port activity (Tx, Rx). 2 x RTU port activity (Tx, Rx). 1 x KNX programming/bus. 1 Push buttons 1 x KNX programming. 1 Console port EIA232. DB9 female connector (DCE). SELV Configuration Via console port. 2 Firmware Allows upgrades via console port. Operational temperature -40 C to +70 C Operational humidity 5% to 95%, non condensing Protection IP20 (IEC60529). RoHS conformity Compliant with RoHS directive (2002/95/CE). Norms and standards CE conformity to EMC directive (2004/108/EC) and Low-voltage directive (2006/95/EC) EN EN EN EN Not operational for the moment. Reserved for future use. Standard cable DB9male-DB9female 1,8 meters long is supplied with the device for connection to a PC COM port for configuring and monitoring the device. The configuration software, compatible with Windows operating systems, is also supplied. 8 / 9
9 Dimensions Power RS232/RS485 KNX port 58 mm Console port 107 mm 105 mm Recommended available space for its installation into a cabinet (wall or DIN rail mounting), with space enough for external connections: 100 mm 115 mm 130 mm 9 / 9
IntesisBox KNX Modbus TCP master
IntesisBox KNX TCP master Gateway for integration of TCP slave devices into KNX control systems. Integrate any TCP slave device into KNX. KNX TCP slave EIB Bus IntesisBox Ethernet slave LinkBoxEIB Configuration
IntesisBox KNX - LON
IntesisBox KNX - Gateway for integration of devices into KNX systems. Integrate Air Conditioning from the main manufacturers (DAIKIN, Mitsubishi Electric, Mitsubishi Heavy Industries, Toshiba, Fujitsu,
KNX Panasonic Air Conditioners
IntesisBox KNX Panasonic Air Conditioners Gateway for Panasonic ECOi and PACi system integration into KNX networks Up to 30 Outdoor units Up to 64 Indoor units PA-AC-KNX-64/128 EIA485 U1U2 line U1U2 line
ModBus Server - KNX. Gateway for integration of KNX equipment into Modbus (RTU and TCP) control systems.
IntesisBox ModBus Server - KNX Gateway for integration of KNX equipment into Modbus (RTU and TCP) control systems. Integrate KNX based lighting control into your SCADA, BMS, PLC "talking" Modbus. Master
IntesisBox Modbus Server Fidelio IP
IntesisBox Server Fidelio IP Gateway for integration of Micros Fidelio Ho management system into (RTU and TCP) enabled control systems. Integrate your Micros Fidelio Ho management system into your master
IntesisBox KNX LG Air Conditioning
IntesisBox KNX LG Air Conditioning Gateway for integration of LG Air Conditioners with KNX control systems. 1. Main Features Direct connection to KNX TP-1 (EIB) bus. Direct connection to LG outdoor unit
IntesisBox. KNX SAMSUNG Air Conditioning. Gateway for integration of Samsung air conditioners into KNX control systems. RS485.
IntesisBox KNX SAMSUNG Air Conditioning Gateway for integration of Samsung air conditioners into KNX control systems. Integrate Samsung Air Conditioners into KNX. KNX EIB Bus IntesisBox RS485 MIM-B13x/B04A
IntesisBox Modbus Server SAMSUNG Air Conditioners
IntesisBox Modbus Server SAMSUNG Air Conditioners Gateway for monitoring and control of Samsung NASA compatible Air Conditioning Systems from any Modbus master device TCP or RTU (BMS, PLC, SCADA, HMI,
IntesisBox BACnet/IP Server - Modbus TCP master
IntesisBox BACnet/IP Server - TCP master Gateway for integration of TCP slave devices into based systems. Integrate any TCP slave device into your BACnet control system. client Ethernet TCP slave client
IntesisBox KNX Mitsubishi Heavy Industries AC
IntesisBox KNX Mitsubishi Heavy Industries AC Gateway for integration of Mitsubishi Heavy Indsutries (MHI) Air Conditioners with KNX control systems. 1. Main Features Direct connection to KNX TP-1 (EIB)
IntesisBox. BACnet/IP Server - LON. Integrate LonWorks devices or systems into BACnet control systems. IntesisBox RS232. Only needed for configuration
IntesisBox Server - LON Gateway for integration of LON devices into BACnet control systems Integrate LonWorks devices or systems into BACnet control systems. BACnet IP client Ethernet LonWorks TP/FT-10
Modbus Server SAMSUNG Air Conditioners
IntesisBox Server SAMSUNG Air Conditioners Gateway for monitoring and control of Samsung Air Conditioning Systems from any master device TCP or RTU (BMS, PLC, SCADA, HMI, TouchPanel ) Master TCP Master
IntesisBox ASCII Server - LON
IntesisBox ASCII Server - LON Gateway for integration of LON devices into ASCII enabled control systems. Integrate Air Conditioning from the main manufacturers (DAIKIN, Mitsubishi Electric, Mitsubishi
IntesisBox Modbus Server - Mitsubishi Electric G50
IntesisBox Server - Mitsubishi Electric G50 Gateway for monitor and control Mitsubishi Electric City Multi Air Conditioning systems from any master device TCP or RTU (BMS, PLC, SCADA, HMI, TouchPanel )
Inwall Room Temperature Unit
Inwall Room Temperature Unit TM11B01KNX TM11B11KNX TM11B21KNX Product Handbook Product: Inwall Room Temperature Unit Order Code: TM11B01KNX TM11B11KNX TM11B21KNX Application Program ETS: TM11B_1KNX Inwall
User manual Compact Web PLC WP240 series IEC-line
User manual Compact Web PLC WP240 series IEC-line update: 09-01-2014 IEC-line by OVERDIGIT overdigit.com 1. General description The WP240 device is a PLC, programmable in IEC61131-3 language using CoDeSys
IntesisBox. Making Building Automation go further. KNX EIB Products
IntesisBox Making Building Automation go further KNX EIB Products October 2008 Overview of products KNX EIB gateways and interfaces designed for integration of third party systems into KNX control systems
Central Communication Unit
Central Communication Unit for Synco 00 and Synco RXB OZW Central communication unit for the remote operation and supervision of Synco plants. Use Types of plant Types of building Operators The OZW central
Electronic Control Devices The European Product Catalogue 2007
FX14 Field Controller (1/4) FX14 Field Controller The FX14 is an equipment field controller in the Facility Explorer range of products. The controller is designed specifically for commercial Heating, Ventilating,
TX OPEN RS232/485 module
s 8 185 8185P01 TX-I/O ; DESIGO OPEN TX OPEN RS/485 module for integrating third-party systems and devices to DESIGO (V4 or higher) TXI1.OPEN Platform to integrate third-party systems and devices to the
Electronic Control Devices The European Product Catalogue 2007
FX07 Field Controller (1/4) FX07 Field Controller Display Model Dimensions in mm (inches) The FX07 is a terminal unit controller in the Facility Explorer range of products. The controller is designed specifically
PCS0100en 02.2008. Persy Control Services B.V. Netherlands
P-Bus Gateway PBGW2.128 Universal gateway between the P-bus protocol and open standard protocols. The variety of available electrical interfaces on the gateway offers a wide range of possibilities for
Rack mounted telephone- and leased line modem for industrial applications
Rack mounted telephone- and leased line modem for industrial applications TR-6 Rack modem for industrial PSTNand /-wire leased line applications The TR-6 is an analogue V. 9 -rack PSTN modem as well as
230 V~ Room Thermostat
230 V~ 369813a 1 07.02.15 The 230 V~ room thermostat adds temperature control to the LutronR hotel guestroom control solution. Controls 2-pipe, 4-pipe, and 3 fan-speed fan coil units. Compatible with LutronR
COMPALARM C2C ALARM SYSTEM
INSTRUCTION MANUAL IM670-U v0.1 COMPALARM C2C ALARM SYSTEM GENERAL Compact alarm system, with a basic module of 12 signals Multiple modules coupling possibility Easy printing of the alarm points description
Zlinx Wireless I/O. Peer-to-Peer and Modbus I/O B&B ELECTRONICS PRODUCT INFORMATION
Modular, Customizable Wire Replacement 128 / 256 Bit AES Encryption Software Selectable RF Transmit Power Software Selectable Over-the-air Data Rate Modbus ASCII /RTU Compatible Wide Operating Temperature
Switch Actuator, 8-fold, 10 A, MDRC AT/S 8.10.1, GH Q631 0075 R0111
, GH Q631 0075 R0111 The 8-fold switch actuator is a DIN rail mounted device for insertion in the distribution board. It is connected to the EIB via a bus terminal. In the event of bus voltage failure,
KNX Interface. User Manual PM00A00IRI
KNX Interface User Manual PM00A00IRI 1/9 1. Index 1. Index...2 2. Preface... 3 2.1. Overview... 3 2.2. System description... 3 2.3. Application programs... 3 2.4. Documentation... 3 3. Mechanical reference...
Power Switch-8. Master. Slave. User's Guide. Power Management
Power Switch-8 Power Management Master Slave User's Guide V.02/2004 Power Switch-8 Power Switch-8 is a couple of power control units made of a Master named Power Switch Master and a slave named Power Switch
Telephone- and leased line modem for industrial applications TD-36
Telephone- and leased line modem for industrial applications TD-36 Modem for industrial PSTN- and leased line applications The TD-36 is an analogue V.34 PSTN modem as well as an industrial 2-wire leased
User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M)
Document code: MN67038-2_ENG Revision 1.400 Page 1 of 25 User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M) for
Inwall 4 Input / 4 Output Module
Inwall 4 Input / 4 Output Module IO44C02KNX Product Handbook Product: Inwall 4 Input / 4 Output Module Order Code: IO44C02KNX 1/27 INDEX 1. General Introduction... 3 2. Technical data... 3 2.1 Wiring Diagram...
Industrial RS-232/ RS-422/ RS-485 over Ethernet Media Converter
Industrial RS-232/ RS-422/ RS-485 over Ethernet Media Converter Serial Interface One RS-232 port and one RS-422/485 port to 10/Base- TX Media Conversion Cost effective solutions of RS-232/ RS-422/ RS-485
EDI Distributor Control Interface Wiring and Setup Instructions
Universal I/O EDI Distributor Control Interface Wiring and Setup Instructions EDI UNIVERSAL I/O INTERFACE MODULE The only interface needed for EDI-V5 controls Network compatible with all older EDI controls
SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual
SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual Version 1.0 - January 20, 2015 CHANGE HISTORY Version Date Description of Changes 1.0 January 20, 2015 Initial Publication
ENET-710. ENET-710 - Ethernet Module ENET-710 JAN / 06 FOUNDATION
ENET-710 ENET-710 - Ethernet Module JAN / 06 ENET-710 FOUNDATION E N E T 7 1 0 ME smar www.smar.com Specifications and information are subject to change without notice. Up-to-date address information is
PXG3.W100. Web interface BACnet/IP. Desigo PX
s 9 294 Desigo PX Web interface BACnet/IP PXG3.W100 Local or remote operation of one or multiple PX automation station(s) via Desigo Touch Panels (TP) and standard web browser Connection via Ethernet Central
Product Manual. ABB i-bus KNX IP Interface IPS/S 2.1. Intelligent Installation Systems ABB
Product Manual ABB i-bus KNX IP Interface IPS/S 2.1 Intelligent Installation Systems ABB This manual describes the function of the IP Interface IPS/S 2.1 with the application program IP Interface. Subject
Modbus Communications for PanelView Terminals
User Guide Modbus Communications for PanelView Terminals Introduction This document describes how to connect and configure communications for the Modbus versions of the PanelView terminals. This document
Bluetooth HC-06 with serial port module Easy guide
1 Bluetooth HC-06 with serial port module Easy guide This manual consists of 3 parts: PART 1. Overview of Bluetooth HC-06 module with serial port. PART 2. Installing Bluetooth HC-06 module with Bolt 18F2550
ABB i-bus EIB / KNX Analogue Input AE/S 4.2
Product Manual ABB i-bus EIB / KNX Analogue Input AE/S 4.2 Intelligent Installation Systems This manual describes the functionality of Analogue Input AE/S 4.2. Subject to changes and errors excepted. Exclusion
Vroom Hardware manual ver. 1.00 Code 114VROOHWE00. Vroom CANBUS USER INTERFACE WITH LCD GRAPHIC DISPLAY AND WITH TEMPERATURE AND HUMIDITY SENSOR
Vroom CANBUS USER INTERFACE WITH LCD GRAPHIC DISPLAY AND WITH TEMPERATURE AND HUMIDITY SENSOR ENGLISH HARDWARE MANUAL ver. 1.00 CODE 114VROOHWE00 page 1 of 22 Important Important Read these instructions
T3 Series. General Purpose IO for Integrators
General Purpose IO for Integrators -1- TABLE OF CONTENTS Table of Contents Technical Data 3 Standard Operation 4 Inputs 4 Outputs 4 Analog Output Calibration 4 Bandrate 4 Master Timer Clock Function for
M90-19-R5. RS232 to RS422/RS485 Isolated Universal Converter. 1. Introduction. 2. Function diagram
to RS422/RS485 Isolated Universal Converter 1. Introduction The converts serial data from the standard to either RS422 or RS485. Features: Universal converter can be used with both and other manufacturer
Shutter Actuator Standard, 4-fold, 230 VAC, MDRC RA/S 4.230.1, GH Q631 0076 R0111. ABB i-bus EIB
, GH Q631 0076 R0111 2CDC 071 240 F0003 The Shutter Actuator Standard is used to control a maximum of four independent 230 VAC drives for positioning shutters, blinds, awnings and other hangings as well
User Manual Revision English
Document code: MN67507_ENG Revision 1.102 Page 1 of 16 User Manual Revision 1.102 English Gateway / Bridge Modbus TCP Server to Modbus RTU Master (Order Code: HD67507 HD67507M) for Website information:
Application/Connection Examples
This Quick Start Guide is designed to familiarize the user with the connection and configuration of the DTS-305 DIN rail mounted single / 3 phase power & energy meter with RS-485 or TCP communications.
Industrial RS-232/ RS-422/ RS-485 over Ethernet Media Converter
ICS-2 S15 Industrial RS-232/ RS-422/ RS-485 over Ethernet Media Converter Cost Effective Solution for RS-232 / RS-422 / RS-485 to Industrial Ethernet Application PLANET ICS-210x series Smart Media Converter
JNIOR. Overview. Get Connected. Get Results. JNIOR Model 310. JNIOR Model 312. JNIOR Model 314. JNIOR Model 410
The INTEG is an Ethernet I/O (digital, analog) device that monitors and controls a small set of process signals. functions as both basic I/O for integration with another application or system AND as a
ABB i-bus EIB / KNX EIB Monitoring Unit EUB/S 1.1
Product Manual ABB i-bus EIB / KNX EIB Monitoring Unit EUB/S 1.1 Intelligent Installation Systems This manual describes the function of the EIB monitoring module EUB/S 1.1 with the Application program
IntesisBox DK-RC-ENO-1iC. EnOcean Interface for DAIKIN Air Conditioners Compatible with SKY and VRV lines
IntesisBox DK-RC-ENO-1i DK-RC-ENO-1iC EnOcean Interface for DAIKIN Air Conditioners Compatible with SKY and VRV lines User's Manual r1 eng Issue Date: 02/2012 Intesis Software S.L. All Rights Reserved.
Process Control and Automation using Modbus Protocol
Process Control and Automation using Modbus Protocol Modbus is the fundamental network protocol used in most industrial applications today. It is universal, open and an easy to use protocol. Modbus has
DLC - Ethernet MANUALE UTENTE USER'S MANUAL
DLC - Ethernet MANUALE UTENTE USER'S MANUAL 06/2004 INDEX 1. Introduction...1 2. Converter Description...2 2.1 Ethernet connector... 3 2.2 Power supply connector... 3 2.3 Serial Rs485 connector... 4 3.
Product and functional description
Product and functional description The KNX / DALI gateway N 141/02 is a 4 MU wide, DINrail mounted KNX device with one DALI interface to which up to 64 DALI actuators (e.g. DALI ballasts) can be connected
EGX100 Ethernet gateway
E90463 PB101556 The EGX100 serves as an Ethernet gateway for PowerLogic System devices and for any other communicating devices utilizing the Modbus protocol. The EGX100 gateway offers complete access to
TM7BDM8B expansion block - TM7 - IP67-8 DI/DO - 24V DC - 0.5 A - M8 connector
Product datasheet Characteristics TM7BDM8B expansion block - TM7 - IP67-8 DI/DO - 24V DC - 0.5 A - M8 connector Main Range of product Product or component type Range compatibility Enclosure material Bus
OZS164... Web server. For LPB/BSB plants
s 5 711 Web server For LPB/BSB plants OZS164... Remotely operate and monitor a LPB or BSB device Web browser operation via PC/laptop or Smartphone SMS operation via mobile phone (OZS164.23) 2 digital inputs
LM058 Bluetooth v2.0, v2.1 RS232 Serial Adapter - SMA Connector Standalone (With Embedded Bluetooth v2.0 / v2.1 Stack)
Bluetooth v.0, v. RS Serial Adapter - SMA Connector Revised /DEC/0 mm mm mm Features Bluetooth v.0, v. wireless technology dbm Tx Power and - dbm Rx Sensitivity Serial (RS) interface Serial Port Profile
Air flow meter Model A2G-25
Electronic pressure measurement Air flow meter Model A2G-25 WIKA data sheet SP 69.04 Applications For measuring the air flows of radial ventilators For measuring air flows in ventilation pipes and ducts
Different Ways of Connecting to. 3DLevelScanner II. A.P.M Automation Solutions LTD. www.apm-solutions.com Version 3.0
3DLevelScanner II Different Ways of Connecting to 3DLevelScanner II A.P.M Automation Solutions LTD. www.apm-solutions.com Version 3.0 2 Different Ways of Connecting to 3DLevelScanner II Version 3.0 Table
ZC-24DO CANopen I/O Module: 24 Digital Outputs
Z-PC Line EN ZC-24DO CANopen I/O Module: 24 Digital Outputs Installation Manual Contents: - General Specifications - Technical Specifications - Installation Rules - Electrical connections - DIP-switches
Waveguide Access Point WGA631. Product Guide
Waveguide Access Point Product Guide Waveguide Access Point Contents 1. Description............................ 3 2. Application............................ 3 3. Technical data... 4 4. Physical interfaces......................
SEZ220. Signal Converter. Synco 200. With preprogrammed standard applications Freely programmable Menu-driven operation. Use
s 5 146 Synco 200 Signal Converter SEZ220 With preprogrammed standard applications Freely programmable enu-driven operation Use The signal converter is for use in HVAC plant to provide minimum / maximum
Industrial RS-232/ RS-422/ RS-485 over Ethernet Media Converter
/ S15 / Industrial RS-232/ RS-422/ RS-485 over Ethernet Media Converter Serial Interface One RS-232 port and one RS-422/485 port to one Base-FX Media Conversion Cost effective solutions of RS-232/ RS-422/
QSE-CI-NWK-E Control Interface
QSE-CI-NWK-E Control Interface 369373e 1 04.05.16 The QSE-CI-NWK-E is a versatile integration access point for Lutron QS-based systems. Through either RS232 or TCP / IP over Ethernet, third-party devices
Push button sensor 3 comfort 3-gang Push button sensor 3 comfort 6-gang (3+3)
KNX/EIB Product documentation Issue: 05.08.2010 629x1220 Push button sensor 3 comfort 1-gang Push button sensor 3 comfort 2-gang (1+1) Push button sensor 3 comfort 3-gang Push button sensor 3 comfort 4-gang
Product Manual. ABB i-bus KNX Data Logging Unit BDB/S 1.1. Intelligent Installation Systems ABB
Product Manual ABB i-bus KNX Data Logging Unit BDB/S 1.1 Intelligent Installation Systems ABB This manual describes the function of the Data Logging Unit BDB/S 1.1. Subject to changes and errors excepted.
LAUREL. Laureate Quadrature Encoder Position & Rate Meter ELECTRONICS, INC. Features. Description
LAUREL ELECTRONICS, INC. Laureate Quadrature Encoder Position & Rate Meter Features Accepts low-level differential or single-ended 5V logic level outputs from quadrature encoders Quadrature count x1, x2
Logic controllers. Modicon Easy M100. For simple machines up to 40 I/O. Catalog. September 2014
Logic controllers Modicon Easy M100 For simple machines up to 40 I/O Catalog September 2014 Contents Modicon TM Easy M100 logic controllers Presentation Introduction... page 2 A user-oriented range of
Programmable Terminal. NPSeries. Easy Setup with the Low-cost, Compact NP Series
Programmable Terminal NPSeries Easy Setup with the Low-cost, Compact NP Series Simpler and More Versatile.OMRON s Compact NP Series Connect! Easier connection to OMRON PLCs and Temperature Controllers,
16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide
16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide 1. Introduction Thank you for purchasing this 16-Port RS232 to USB2.0 High Speed Multi Serial Adapter. It is an
Temperature Controller (Heat Pumps)
3 346 Temperature Controller (Heat Pumps) RWD34 RWD44 For comfort control in HVAC & R systems Standalone electronic controller Programmable controller with preconfigured applications Two universal inputs
ABB i-bus KNX Fan Coil Controller FC/S 1.1
Product manual ABB i-bus KNX Fan Coil Controller FC/S 1.1 Intelligent Installation Systems Contents Page 1 Introduction... 2 2 Device technology... 3 3 Application and planning 3.1 Heating, ventilation
TX2123 RS485 TO ETHERNET ADAPTOR
TX2123 RS485 TO ETHERNET ADAPTOR Converts Datacomms between fibre optic Modbus TCP over Ethernet and hard-wired copper Modbus RTU over RS485 Fibre Optic MODBUS TCP/ IP Ethernet Copper MODBUS RTU RS485
Connect Serial Cable from Terminal Blocks to Computer Comport for Bridge Configuration
Tech Note 391 Configuring Modicon Modbus to Ethernet Bridge 170-CEV-300-10 All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more
OCI Service Tool. Siemens Building Technologies HVAC Products. ACS plant operating software and OCI700 service interface
5 655 Service Tool ACS plant operating software and OCI700 service interface OCI700.1 Service tool for commissioning and the diagnosis of HVAC controllers of the Synco, SIGMAGYR and ALBATROS ranges. Use
ABB i-bus EIB / KNX DALI-Gateway DG/S 8.1
Product manual ABB i-bus EIB / KNX DALI-Gateway DG/S 8.1 Intelligent Installation Systems This manual describes the function of the DALI-Gateway DG/S 8.1 with the application program Dim Slave Lightscenes
RDJ10RF/SET. Wireless room temperature controller with 24-hour time switch and LCD. Programmable, for heating systems
3 072 RDJ10RF RCR10/433 Wireless room temperature controller with 24-hour time switch and LCD Programmable, for heating systems RDJ10RF/SET Operating modes: Automatic, Comfort, Energy Saving, and Frost
HARTING econ 3000 Introduction and features
HARTING Introduction and features HARTING es, unmanaged, for installation in control cabinets General Description Features The Fast es of the product family HARTING are suitable for industrial applications
INSTALLATION GUIDE. MODBUS RECEIVER RX MODBUS RS485 MULTI (868 MHz) IG UK c
INSTALLATION GUIDE MODBUS RECEIVER RX MODBUS RS485 MULTI 900-022 (868 MHz) IG UK 900-022-c DESCRIPTION RX MODBUS RS485 MULTI 900-022 ❹ ❿ ⓫ ❷ ❸ ❾ ❽ ⓬ ❶ ❼ ❻ ❺ ⓭ ❶ Identification label ❷ Screws for opening/closing
1 Serial RS232 to Ethernet Adapter Installation Guide
Installation Guide 10/100 Mbps LED (amber color ) Link/Activity LED (green color ) 1. Introduction Thank you for purchasing this 1-port RS232 to Ethernet Adapter (hereinafter referred to as Adapter ).
Communication standards and Carel solutions
Brugine March 2002 Communication standards and Carel solutions Modbus All Carel controllers: GATEWAYMB0 pco 2 - Direct connection through RS232 serial card PCO200MDM0 RS485 serial card PCO2004850 BIOS
OZW772... V2.0. Web server. Synco TM, Synco TM living
s 5 701 Web server Synco TM, Synco TM living OZW772... V2.0 The OZW772 web server allows for remote operation and monitoring of plants via the web and send faults and system reports to e-mail recipients.
TELEDYNE HASTINGS INSTRUMENTS
TELEDYNE HASTINGS INSTRUMENTS THCD 100 Self contained display for flow meter/controller and pressure transducers FEATURES 16-Bit Resolution ± 0.2% Reading +1 Digit Accuracy 0-5 VDC Setpoint via Front Panel
Unidirectional Transmitter/ Receiver Units Introduction
Unidirectional Transmitter/ Receiver Units Introduction Wireless Input/Output (I/O) connects directly to analog, discrete and pulse transducer signals. The signals are transmitted by radio and either re-created
Central Communication Unit
Central Communication Unit for LPB/BSB plants Series B OCI6 Central communication unit for the remote operation and supervision of LPB plants with a maximum of 6 LPB/BSB units Use Plant Buildings Operators
Automated System Accessories
Weatherford s automated systems accessory components are used to expand input/ output (I/O) capacity, meet power requirements, provide communications connectivity, and supply the instrumentation interface
Technologies Inc. ETMBTCP Installation And User Guide
Technologies Inc. ETMBTCP Installation And User Guide Device Description Connectors: Input / Output Power Bottom Connector Top Connector 9-32 VDC (100mA) or 12-24VAC (100mA) RJ-45 10/100mbit half/full
ELCOMPONENT LTD. User Manual
ELCOMPONENT LTD R-DCU - Remote Data a Collection Unit User Manual al CONTENTS Page 1. GENERAL... 1 2. SPECIFICATION... 4 3. INSTALLATION AND INSTRUCTIONS... 6 4. INSTRUMENT SET-UP AND RESET... 11 All rights
Using Modbus with Mach3 By Peter Homann
Using Modbus with Mach3 By Peter Homann Eventually a new user to Mach3 will hear the term Modbus being bandied about. This article explains how it can be used with Mach3. But, before diving in and showing
Technical Note A007 Modbus Gateway Vantage Pro2 25/09/2009 Rev. A 1 de 7
1 de 7 1. Introduction This Technical Note explains how to configure the Modbus Gateway for Vantage Pro2. The Modbus Gateway allows the easy connection of a PLC (Programmable Logic Controller), RTU (Remote
Optimize your simple machines... Modicon M218 Selection Guide
Optimize your simple machines... Modicon M218 Selection Guide Compact Solution for Simple Machines Optimized Logic Controller Modicon M218 With intelligent software platform, specialized functional s,
NetBiter webscada Modbus User Manual
User Manual IntelliCom Innovation AB Pilefeltsgatan 93-95 SE-302 50 Halmstad SWEDEN Phone +46 35 17 29 90 Fax +46 35 17 29 09 email info@intellicom.se www www.intellicom.se Revision List Revision Date
User Manual Revision English
Document code: MN67510_ENG Revision 1.000 Page 1 of 14 User Manual Revision 1.000 English Gateway / Bridge Modbus TCP Client to Modbus RTU Slave to connect a Modbus TCP Server (Order Code: HD67510 HD67510M)
SEZ220. Signal Converter. Synco 200. With preprogrammed standard applications Freely programmable Menu-driven operation. Use
s 5 146 Synco 200 Signal Converter SEZ220 With preprogrammed standard applications Freely programmable enu-driven operation Use The signal converter is for use in HVAC plant to provide minimum / maximum
Digital input modules
8 172 TX-I/O Digital input modules TXM1.8D TXM1.16D Two fully compatible versions: TXM1.8D: 8 inputs, each with a three-color LED (green, yellow or red) TXM1.16D: As TXM1.8X, but 16 inputs, each with a
User Manual. cmt-svr Startup Guide
User Manual cmt-svr Startup Guide Table of Contents Chapter 1 Overview... 1 1.1 Specification... 1 1.2 Dimensions... 2 1.3 Connector pin designations... 3 1.4 USB host port and SD card slot... 3 1.5 Ethernet
USER MANUAL Z-KEY MODBUS ETHERNET SERIAL GATEWAY AND SERIAL DEVICE SERVER. Via Austria, PADOVA ITALY
USER MANUAL Z-KEY MODBUS ETHERNET SERIAL GATEWAY AND SERIAL DEVICE SERVER SENECA s.r.l. Via Austria, 26 35127 PADOVA ITALY Tel. +39.049.8705355 8705359 Fax. +39.049.8706287 Web site: www.seneca.it Technical
TRP-C31M MODBUS TCP to RTU/ASCII Gateway
TRP-C31M MODBUS TCP to RTU/ASCII Gateway User s Manual Printed Feb. 2007 Rev 1.0 Trycom Technology Co., Ltd 1F, No.2-11, Sihu street, Yingge Township, Taipei, Taiwan ROC Tel: 886-2-86781191, Fax: 886-2-86781172
connecdim Gateway G1 Ethernet TCP/IP to DALI
Gateway G1 Ethernet TCP/IP to LI Independent lighting control for up to 256 LI gears on 4 LI lines Can be expanded by connecting multiple gateways on the same network Cloud based web interface for configuration