Assembling the Sensor Board Version 5.0
|
|
|
- David Barrett
- 7 years ago
- Views:
Transcription
1 1 Assembling the Sensor Board Version 5.0 Image Description Quantity per Sensor PCB Board 1 Resistor # Code (000) Value: 0 Ohm 6 Resistor # Code (1001) Value: 1K Ohm 4 Resistor # Code (1002) Value: 10K Ohm 6 Resistor # Code (1003) Value: 100K Ohm 3
2 2 Capacitor Value: 0.1 uf 3 LED Color: RED 3 LED Color: GREEN 1 LED Color: Blue 3 Inductor # Code (104) Value: 100mH 3 OP Amp 3 Potentiometer 3
3 3 Transistor 3 MosFET 1 6 Pin Header 1 Jumper Cables 6
4 4 Detailed Description PCB Board Front of Board Back of Board LED (Red and Green) Front Back LED (Blue) Front
5 5 Assembling the Krisys Sensor Board Version 5.0 with Extra LEDs STEP Number Type of Part Value Location Type of Mount SMD/Through 1 Diode D4,D5,D6 SMD YES 2 Resistor 100K R10,R11,R12 SMD NO 3 Resistor 10K R19,R20,R21 SMD NO 4 Capacitor 0.1 uf C1,C2,C3 SMD NO 5 Resistor 10K R4,R5,R6 SMD NO 6 Resistor Zero R7,R8,R9 SMD NO 7 Red LEDs N/A D1,D2,D3 SMD YES 8 Resistor 1K R1,R2,R3 SMD NO 9 Resistor 1K R99 SMD NO 10 Green LEDs N/A D99 SMD YES 11 Resistor Zero R16,R17,R18 SMD NO 12 Blue LED N/A D16,D17,D18 SMD YES 13 OpAmp N/A U1,U2,U3 Through Hole YES 14 Potentiometer N/A R13,R14,R15 Through Hole YES 15 MosFET 2N7000 Q1 Through Hole YES 16 Headers N/A J99 Through Hole NO 17 Inductors 100mH L1,L2,L3 Through Hole NO Polarity/ Orientation Dependent
6 6 STEP 1 Diode Transistor D4,D5,D6 - Find the part depicted above. You will need three of them for this STEP. - This part has three leads and must be soldered in a specific way. - Look at the pattern layout printed on the board to determine the orientation of the diode on the board. - Solder them in at D4, D5, D6 Note: When soldering this part, do not hold the soldering iron to it for too long. Heating the part for too long (more than a few seconds) might damage it.
7 7 STEP 2 Resistor (100K) Resistor # Code (1003) Value: 100K Ohm R10, R11, R12 - Find the part depicted above. You will need three of them for this STEP. - Since it is a resistor, it can be soldered in any direction. - Solder them in at R10, R11, R12
8 8 STEP 3 Resistor (10K) Resistor # Code (1002) Value: 10K Ohm R19, R20, R21 - Find the part depicted above. You will need three of them for this STEP. - Since it is a resistor, it can be soldered in any direction. - Solder them in at R19, R20, R21
9 9 STEP 4 Capacitor (0.1uF) Capacitor Value: 0.1 uf C1,C2,C3 - Find the part depicted above. You will need three of them for this STEP. - This capacitor can be soldered in any direction. - Solder them in at C1,C2,C3
10 10 STEP 5 Resistor (10K) Resistor # Code (1002) Value: 10K Ohm R4,R5,R6 - Find the part depicted above. You will need three of them for this STEP. - Since it is a resistor, it can be soldered in any direction. - Solder them in at R4,R5,R6
11 11 STEP 6 Resistor (Zero) Resistor # Code (100) Value: Zero Ohm R7, R8, R9 - Find the part depicted above. You will need three of them for this STEP. - Since it is a resistor, it can be soldered in any direction. - Solder them in at R7, R8, R9
12 12 STEP 7 Red LEDs LED Color: RED D1,D2,D3 - Find the part depicted above. You will need three of them for this STEP. - Since it is an LED, it has to be soldered in a specific orientation. NOTE: Look at the next page for more information on how to orient the LED onto the board. - Solder them in at D1,D2,D3
13 13 - The white lettering on the board indicates the positive (+) and negative (-) sides. LEDs (RED) Front Back
14 14 STEP 8 Resistor (1K) Resistor # Code (1001) Value: 1K Ohm R1, R2, R3 - Find the part depicted above. You will need three of them for this STEP. - Since it is a resistor, it can be soldered in any direction. - Solder them in at R1, R2, R3
15 15 STEP 9 Resistor (1K) Resistor # Code (1001) Value: 1K Ohm R99 - Find the part depicted above. You will need ONE of them for this STEP. - Since it is a resistor, it can be soldered in any direction. - Solder it in at R99
16 16 STEP 10 Green LEDs LED Color: GREEN D99 - Find the part depicted above. You will need ONE of them for this STEP. - Since it is an LED, it has to be soldered in a specific orientation. NOTE: Look at the next page for more information on how to orient the LED onto the board. - Solder it in at D99
17 17 - The white lettering on the board indicates the positive (+) and negative (-) sides. LEDs (GREEN) Front Back
18 18 STEP 11 Resistor (Zero) Resistor # Code (100) Value: Zero Ohm R16, R17, R18 - Find the part depicted above. You will need three of them for this STEP. - Since it is a resistor, it can be soldered in any direction. - Solder them in at R16, R17, R18
19 19 STEP 12 Blue LEDs LED Color: BLUE D16, D17, D18 - Find the part depicted above. You will need three of them for this STEP. - Since it is an LED, it has to be soldered in a specific orientation. NOTE: Look at the next page for more information on how to orient the LED onto the board. - Solder them in at D16, D17, D18
20 20 - The white lettering on the board indicates the positive (+) and negative (-) sides. LED (BLUE) FRONT
21 21 STEP 13 OP Amp OP Amp U1,U2,U3 - Find the part depicted above. You will need three of them for this STEP. - Since it is an IC (integrated Circuit), it has to be soldered in only one way for it to work. NOTE: Look at the next page for more information on how to orient the IC onto the board - Solder them in at U1, U2, U3
22 22 - The image below shows the area where an IC should go. - The image to the right shows the IC. - On ICs, the indicator which is usually a circle indicates the starting point where the counting of the leads begins
23 23 STEP 14 Potentiometer Potentiometer R13, R14, R15 - Find the part depicted above. You will need three of them for this STEP. - This part has three leads and fits on the board in only one orientation. - Solder them in at R13, R14, R15
24 24 STEP 15 MosFET Transistor Q1 - Find the part depicted above. You will need only one for this STEP. - Make sure that the silhouette of the transistor is oriented in the same way as the white picture in the board. - Solder the transistor at Q1.
25 25 STEP 16 Headers 6 Pin Header J99 - Find the part depicted above. You will need only one for this STEP. - This header is going to be used to connect to the main controller board. - Solder it in at J99.
26 26 STEP 17 Inductors (100mH) Inductor # Code (104) Value: 100mH L1,L2,L3 - Find the part depicted above. You will need three for this STEP. - The inductor can be soldered in any direction. NOTE: This part is inserted from the back of the board and soldered from the front. Look at the next page to view the board from the back. - Solder them in at L1, L2, L3.
27 - Looking at the back of a completed board. 27
Joule Thief 3.0 Kit. June 2012, Rev 1 1 http://www.easternvoltageresearch.com Joule Thief 3.0
Kit Instruction Manual Eastern Voltage Research, LLC June 2012, Rev 1 1 http://www.easternvoltageresearch.com HIGH BRIGHTNESS LED THIS KIT USES A 1W CREE, HIGH BRIGHTNESS LED. DO NOT STARE AT THIS (OR
Assembly and User Guide
1 Amp Adjustable Electronic Load 30V Max, 1 Amp, 20 Watts Powered by: 9V Battery Assembly and User Guide Pico Load is a convenient constant current load for testing batteries and power supplies. The digital
Modifying the Yaesu FT-847 External 22.625 MHz Reference Input
Modifying the Yaesu FT-847 External 22.625 MHz Reference Input David Smith VK3HZ Introduction This document describes the modification of an FT-847 to allow an external 22.625 MHz Reference oscillator
Assembly Instructions: Shortwave Radio Kit
Assembly Instructions: Shortwave Radio Kit MTM Scientific, Inc P.O. Box 522 Clinton, MI 49236 U.S.A Introduction Fig 1: The assembled Shortwave Radio Kit The SHORTWAVE RADIO KIT (#SWRAD) from MTM Scientific
DET Practical Electronics (Intermediate 1)
DET Practical Electronics (Intermediate 1) 731 August 2000 HIGHER STILL DET Practical Electronics (Intermediate 1) Support Materials CONTENTS Section 1 Learning about Resistors Section 2 Learning about
BUILDING INSTRUCTIONS
etap2hw 38 mm I2C to LCD Interface BUILDING INSTRUCTIONS October 2013 P. Verbruggen Rev 1.01 15-Oct-13 Page 1 Table of Contents Chapter 1 General Information 1.1 ESD Precautions 1.2 Further Supplies 1.3
AUTOMATIC CALL RECORDER JAMECO PART NO. 2163735
AUTOMATIC CALL RECORDER JAMECO PART NO. 2163735 Experience Level: Intermediate Time Required: 1-2 Hours This project automatically records phone calls. The program, along with the adapter records each
PolyBot Board. User's Guide V1.11 9/20/08
PolyBot Board User's Guide V1.11 9/20/08 PolyBot Board v1.1 16 pin LCD connector 4-pin SPI port (can be used as digital I/O) 10 Analog inputs +5V GND GND JP_PWR 3-pin logic power jumper (short top 2 pins
Kit 106. 50 Watt Audio Amplifier
Kit 106 50 Watt Audio Amplifier T his kit is based on an amazing IC amplifier module from ST Electronics, the TDA7294 It is intended for use as a high quality audio class AB amplifier in hi-fi applications
Electronic Circuit Prototyping Techniques
Electronic Circuit Prototyping Techniques Document Revision: 1.01 Date: February, 2007 16301 Blue Ridge Road, Missouri City, Texas 77489 Telephone: 1-713-283-9970 Fax: 1-281-416-2806 E-mail: info@bipom.com
ECEN 1400, Introduction to Analog and Digital Electronics
ECEN 1400, Introduction to Analog and Digital Electronics Lab 4: Power supply 1 INTRODUCTION This lab will span two lab periods. In this lab, you will create the power supply that transforms the AC wall
TEECES DOME LIGHTING SYSTEMS
This lighting system was designed by John V (Teeces) to be a simple, customizable, expandable and affordable solution for dome lighting. An Arduino micro-controller is used to tell LED driver chips which
Build A Video Switcher. Reprinted with permission from Electronics Now Magazine September 1997 issue
Build A Video Switcher Reprinted with permission from Electronics Now Magazine September 1997 issue Copyright Gernsback Publications, Inc.,1997 BUILD A VIDEO SWITCHER FRANK MONTEGARI Watch several cameras
Electronics and Soldering Notes
Electronics and Soldering Notes The Tools You ll Need While there are literally one hundred tools for soldering, testing, and fixing electronic circuits, you only need a few to make robot. These tools
LM 358 Op Amp. If you have small signals and need a more useful reading we could amplify it using the op amp, this is commonly used in sensors.
LM 358 Op Amp S k i l l L e v e l : I n t e r m e d i a t e OVERVIEW The LM 358 is a duel single supply operational amplifier. As it is a single supply it eliminates the need for a duel power supply, thus
step 1 Unpack the lunchbox And check whether you have got all the components~ If you have questions please contact us at: info@unitunlikely.
step 1 Unpack the lunchbox And check whether you have got all the components~ If you have questions please contact us at: info@unitunlikely.com This part is called the PCB (printed circuit board). All
7-SEGMENT DIGITAL CLOCK
57mm 7-SEGMENT DIGITAL CLOCK Large 57mm clock & temperature display with extra unique feature Total solder points: 263 Difficulty level: beginner 1 2 3 4 5 advanced K8089 ILLUSTRATED ASSEMBLY MANUAL H8089IP-1
SYMMETRIC 1A POWER SUPPLY K8042
SYMMETRIC 1A POWER SUPPLY K8042 Low cost universal symmetric power supply ILLUSTRATED ASSEMBLY MANUAL H8042IP-1 Features & Specifications Features low cost universal symmetric power supply just add a suitable
ARDUINO SEVERINO SERIAL SINGLE SIDED VERSION 3 S3v3 (REVISION 2) USER MANUAL
ARDUINO SEVERINO SERIAL SINGLE SIDED VERSION 3 S3v3 (REVISION 2) USER MANUAL X1: DE-9 serial connector Used to connect computer (or other devices) using RS-232 standard. Needs a serial cable, with at least
RS232/DB9 An RS232 to TTL Level Converter
RS232/DB9 An RS232 to TTL Level Converter The RS232/DB9 is designed to convert TTL level signals into RS232 level signals. This cable allows you to connect a TTL level device, such as the serial port on
Overnight Sensations Speaker Kit
Overnight Sensations Speaker Kit Thank you for purchasing the Overnight Sensation cabinet kit. This speaker kit was precision cut using CNC machinery for the best possible fit and finish. With a little
Total solder points: 205 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL BATTERY CHARGER / DISCHARGER K7300 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 205 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL BATTERY CHARGER / DISCHARGER K7300 Automatic (dis)charging of both NiCd and NiMH batteries. ILLUSTRATED ASSEMBLY MANUAL
BMD16N-SD. version 1.2
BMD16NSD version 1.2 Feedback decoder with 16 contacts with integrated current detection for the S88bus Compatible with a.o. Märklin Digital, Uhlenbrock Intellibox, Fleischmann TwinCenter and LDT HSI88
INTERNATIONAL ATOMIC ENERGY AGENCY INSTRUMENTATION UNIT SMD (SURFACE MOUNTED DEVICES) REPAIR S. WIERZBINSKI FEBRUARY 1999
(SURFACE MOUNTED DEVICES) REPAIR S. WIERZBINSKI FEBRUARY 1999 (SURFACE MOUNTED DEVICES) REPAIR 1 TABLE OF CONTENTS PAGE 1. INTRODUCTION 3 2. ADVANTAGES 4 3. LIMITATIONS 4 4. DIALECT 5 5. SIZES AND DIMENSIONS
200W DISCRETE POWER AMPLIFIER K8060
H8060IP-1 200W DISCRETE POWER AMPLIFIER K8060 Ideal for active speaker system or subwoofer, guitar amp, home theatre systems, instrument amp, etc. Features & Specifications Specifications: Excellent value
GLOLAB Universal Telephone Hold
GLOLAB Universal Telephone Hold 1 UNIVERSAL HOLD CIRCUIT If you have touch tone telephone service, you can now put a call on hold from any phone in the house, even from cordless phones and phones without
Name: Bicycle Cellphone Charger Circuit Assembly Manual Device: Nokia/Blackberry List of Components:
Name: Bicycle Cellphone Charger Circuit Assembly Manual Device: Nokia/Blackberry List of Components: Serial numbername Quantity Component number 1 5 V Regulator 1 U2 2 10 MicroFarad Capacitor 1 C1 3 22
POCKET AUDIO GENERATOR K8065
POCKET AUDIO GENERATOR K8065 Great little gadget for service repair, testing, education, etc... ILLUSTRATED ASSEMBLY MANUAL H8065IP-1 VELLEMAN NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be
DUAL ELECTRONIC DICE K3400
DUAL ELECTRONIC DICE K3400 Cheating is no longer possible! ILLUSTRATED ASSEMBLY MANUAL H3400IP-1 VELLEMAN NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Features &
Welcome to this presentation on Switch Mode Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we will look at:
Welcome to this presentation on Switch Mode Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we will look at: How switch mode drivers work, switch mode driver topologies,
Analog control unit for mobile robots
Analog control unit for mobile robots Soldering kit for experimentation For Fischertechnik robots and others Most diverse functions Requires no programming Patented sensor technology Summary We are pleased
C220 PRELIMINARY TUBE PREAMPLIFIER SERVICE MANUAL. SERIAL NO. WS1001 And Above C220. Serial Number W S1001 And Above CONTENTS
Performance Specifications... 2 Notes... 2 Rear Panel... 3 Section Location... 3 Block Diagram... 5-6 Interconnection Diagram... 7-8 Main Schematic and PCB... 9-18 C220 TUBE PREAMPLIFIER CONTENTS Display
Multipurpose Analog PID Controller
Multipurpose Analog PID Controller Todd P. Meyrath Atom Optics Laboratory Center for Nonlinear Dynamics University of Texas at Austin c 00 March 4, 00 revised December 0, 00 See disclaimer This analog
Dashboard Digital Voltmeter
Dashboard Digital Voltmeter...November, 2002 This project is helpful to anyone who drives an automobile. I had found this project at the local libary... in an old publication. I made it and it worked fine.
SUPER SNOOPER BIG EAR
AA-1D Super Snooper Big Ear SPECIFICATIONS Operates on 5 to 9v DC Will drive a small speaker Provides up to 1 watt of audio power Distortion > 0.2% Voltage Gain up to 46 db Size: 1 x 1.95 Rainbowkits.com
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT. Version 2.
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT Version 2.0 Index of Sheets TEACHING RESOURCES Index of Sheets
Cornerstone Electronics Technology and Robotics I Week 15 Voltage Comparators Tutorial
Cornerstone Electronics Technology and Robotics I Week 15 Voltage Comparators Tutorial Administration: o Prayer Robot Building for Beginners, Chapter 15, Voltage Comparators: o Review of Sandwich s Circuit:
Cost. 13p each. 1.50 each
G-QRP Club components This is a service for G-QRP Club members only 6 pole crystal filter SSB 9MHz 2.2kHz 500 Ohm in/out 12 Polyvaricon capacitors 2 gang - 8 to 140pF & 6 to 60pF (tags marked A & O respectively)
VOLUME AND TONE CONTROL - PREAMPLIFIER K8084
H8084IP-1 VOLUME AND TONE CONTROL - PREAMPLIFIER K8084 When using one of our amplifiers (big or small), you always need a volume control and preferably also a tone control Features & specifications When
!Operation:!1. Connect an external power source to J1 (+ and - IN terminals). The
The CB500 Electronic Circuit Breaker is an resettable circuit breaker (fuse) that disconnects power when the trip setting is exceeded. There are 4 trip settings that can easily be changed and set during
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 Control a relay by means of the wellknown DMX512 protocol. ILLUSTRATED ASSEMBLY MANUAL H8072IP-1 Features
400W MONO/STEREO AMPLIFIER
400W MONO/STEREO AMPLIFIER Universal, robust and compact are the words to describe this amplifier. Total solder points: 264 Difficulty level: beginner 1 2 3 4 5 advanced K4005B ILLUSTRATED ASSEMBLY MANUAL
The $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit.
The $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit. Micro Wizard has been manufacturing Pinewood Derby timers for over 10 years.
K4401 SOUND GENERATOR. them at the touch of a button. Specifications
SOUND GENERATOR K4401 Sound effects, tunes, sirens... 10 of them at the touch of a button. Specifications Loudspeakers output : 8 ohm/1w Line output : 1VRms. Power supply : 8 10VDC (9v battery). Max. current
GLOLAB Two Wire Stepper Motor Positioner
Introduction A simple and inexpensive way to remotely rotate a display or object is with a positioner that uses a stepper motor to rotate it. The motor is driven by a circuit mounted near the motor and
K128. USB PICmicro Programmer. DIY Electronics (HK) Ltd PO Box 88458, Sham Shui Po, Hong Kong. http://www.kitsrus.com mailto: peter@kitsrus.
K128 USB PICmicro Programmer DIY Electronics (HK) Ltd PO Box 88458, Sham Shui Po, Hong Kong http://www.kitsrus.com mailto: peter@kitsrus.com Last Modified March 31 2003 Board Construction The board is
X. Dealing with Signature Differences
X. Dealing with Signature Differences One of the most often asked questions that Tracker users ask is "when is a different signature considered a fault?". Simply put, "what makes a bad signature?". To
15 Channel IR transmitter. Total solder points: 53 Difficulty level: beginner 1 2 3 4 5 advanced K8049 ILLUSTRATED ASSEMBLY MANUAL
15 Channel IR transmitter Compatible with most Velleman IR receiver kits, 4 adresses allow the use of multiple receivers in one room. Total solder points: 53 Difficulty level: beginner 1 2 3 4 5 advanced
WHO ANSWERED FIRST? FIND OUT WITH THIS QUIZ BUZZER KIT
WHO ANSWERED FIRST? FIND OUT WITH THIS QUIZ BUZZER KIT BUILD INSTRUCTIONS Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit Board (PCB).
Optical Sensor Interface for AFX Digital LED Timer/Counter by George Warner, Jan. 2003 warnergt@ptd.net
Optical Sensor Interface for AFX Digital LED Timer/Counter by George Warner, Jan. 200 warnergt@ptd.net Abstract This paper presents a design for an optical sensor interface to an AFX Digital LED Timer/Counter.
Portable Cell Phone Charger: Design and Manufacturing
Portable Cell Phone Charger: Design and Manufacturing Miguel Contreras Junior Electrical Engineering California Polytechnic State University 1926 Canyon Circle San Luis Obispo, CA 93410-1710 (408) 655-5010
RC2200DK Demonstration Kit User Manual
Demonstration Kit User Manual Table of contents TABLE OF CONTENTS... 1 QUICK INTRODUCTION... 2 INTRODUCTION... 3 DEMONSTRATION BOARD... 4 POWER SUPPLY SECTION... 5 RS-232 INTERFACE... 6 CONNECTORS... 7
Users Guide for the Non-Inverted LM3886 Kit
Users Guide for the Non-Inverted LM3886 Kit Chipamp.com 1 (14) Users Guide for the Non-Inverted LM3886 Kit 1 INTRODUCTION... 2 1.1 TERMINOLOGY USED IN THIS DOCUMENT... 2 1.2 AMPLIFIER BOARD SCHEMATIC...
Thermal Load Boards Improve Product Development Process
Thermal Load Boards Improve Product Development Process Bernie Siegal Thermal Engineering Associates, Inc. 2915 Copper Road Santa Clara, CA 95051 USA P: 650-961-5900 F: 650-227-3814 E: bsiegal@thermengr.com
Total solder points: 129 Difficulty level: beginner 1 2 3 4 5 advanced LIQUID LEVEL CONTROLLER K2639 ILLUSTRATED ASSEMBLY MANUAL H2639IP-1
Total solder points: 129 Difficulty level: beginner 1 2 3 4 5 advanced LIQUID LEVEL CONTROLLER K2639 Forgotten to turn off the tap, leaking washing machines,... Prevention is better than cure. So use this
The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu
The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu Modifications and typographical errors reserved - Velleman nv. H8098 IP 2 (rev.1.0) Velleman NV, Legen
Design Project: Power inverter
Design Project: Power inverter This worksheet and all related files are licensed under the Creative Commons Attribution License, version 1.0. To view a copy of this license, visit http://creativecommons.org/licenses/by/1.0/,
Electronic Circuit Construction:
Electronic Circuit Construction: Various methods are used for building electronic circuits. The method that you choose depends on a number of factors, including the resources available to you and whether
Building the AMP Amplifier
Building the AMP Amplifier Introduction For about 80 years it has been possible to amplify voltage differences and to increase the associated power, first with vacuum tubes using electrons from a hot filament;
phonostage RIP YOUR VINYL TO BITS, WITH A USB Design
RIP YOUR VINYL TO BITS, WITH A USB phonostage So what do you do with that collection of LPs you have? Sure, they sound great and are fun to listen to, but let s face it, they re not exactly portable. Wouldn
K6002 TEMPERATURE CONTROLLER. Specifications
Total solder points: 169 + 99 + 67 Difficulty level: beginner 1 2 3 4 5 advanced TEMPERATURE CONTROLLER K6002 Unlike a normal thermostat, this kit has two outputs, one for "high" alarm and one for "low"
Assembly Notes. Disclaimer:
Assembly Notes Before you start building your kit, please take time to read the manual in full at least once to enable you to fully understand the procedures and avoid any mistakes. The following notes
K2570 UNIVERSAL POWER SUPPLY 5-14DC / 1A. The easy way to power your ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 18 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL POWER SUPPLY 5-14DC / 1A K2570 The easy way to power your projects. ILLUSTRATED ASSEMBLY MANUAL H2570IP-1 Features & Specifications
K8025 VIDEO PATTERN GENERATOR. Check the picture quality of your monitor or TV, ideal for adjustment or troubleshooting.
K8025 ILLUSTRATED ASSEMBLY MANUAL H8025IP 1 VIDEO PATTERN GENERATOR Check the picture quality of your monitor or TV, ideal for adjustment or troubleshooting. Forum Participate our Velleman Projects Forum
Total solder points: 115 Difficulty level: beginner 1 2 3 4 5 advanced 4 CHANNEL RUNNING LIGHT K8032 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 115 Difficulty level: beginner 1 2 3 4 5 advanced 4 CHANNEL RUNNING LIGHT K8032 Ideal for creating disco light effects, light speed adjustable. Suited for inductive loads. ILLUSTRATED
AXE114S BINARY CLOCK. revolution Revolution Education Ltd. Email: info@rev-ed.co.uk Web: www.rev-ed.co.uk Version 1.1 12/09/08 AXE114.PMD.
AXE114S BINARY CLOCK Features: The PICAXE binary clock kit tells the time by lighting up blue LEDs in a binary pattern. This is a useful tool for teaching students binary code or simply just confusing/
Bill Conkling July 2012
Bill Conkling July 2012 Introduction: For any ham, there are moments that are priceless, like snagging that elusive rare DX station on a deserted island that hasn t been activated in 52 years. And certainly,
EXPRESS PCB TUTORIAL Author: Lee Morey Revised: JE Feb 2015
EXPRESS PCB TUTORIAL Author: Lee Morey Revised: JE Feb 2015 Getting Started There are several resources for learning how to layout schematics and PCBs. And there are several popular commercial packages.
P105 SINGLE STICK REVERSER PICTURE 1: PCB with headers PICTURE 3: Resistors added PICTURE 5: Add tactile switch (button) PICTURE 7: Fit lead and PIC chip. NOTE! ANTI-STATIC PRECAUTIONS REQUIRED PICTURE
This lab is due 5:30PM Tuesday November 2, 2010 at 115 Hackerman Hall
M.E. 530.420 Lab 7: Printed Circuit Board Design Louis L. Whitcomb Department of Mechanical Engineering G.W.C. Whiting School of Engineering The Johns Hopkins University This lab is due 5:30PM Tuesday
CHECKING MOSFETS ON PCB 1011
Figura1 MEASUREMENTS ON GOOD MOSFET Figura2 MEASUREMENT ON GOOD MOSFET MOSFET CHECK ON PCB 1011 Pag 1 de 9 Septiembre 2004 ruc Figura 3 MESUREMENT ON GOOD MOSFET Figura 4 MEASUREMENT ON A BRANCH WITH ONE
BUILD YOUR OWN RC SWITCH (Issue 3)
PART ONE SINGLE ELECTRONIC RC SWITCH Fancy switching the lights using your radio, then here is a circuit you may consider building. It only uses one IC and seven other components for a single switch and
Robot Board Sub-System Testing. Abstract. Introduction and Theory. Equipment. Procedures. EE 101 Spring 2006 Date: Lab Section # Lab #6
EE 101 Spring 2006 Date: Lab Section # Lab #6 Name: Robot Board Sub-System Testing Partner: No Lab partners this time! Abstract The ECEbot robots have a printed circuit board (PCB) containing most of the
Physics 3330 Experiment #2 Fall 1999. DC techniques, dividers, and bridges R 2 =(1-S)R P R 1 =SR P. R P =10kΩ 10-turn pot.
Physics 3330 Experiment #2 Fall 1999 DC techniques, dividers, and bridges Purpose You will gain a familiarity with the circuit board and work with a variety of DC techniques, including voltage dividers,
Glolab Talking Phone Dial Monitor
Introduction The detects the tones generated when numbers are dialed on your touch tone telephone and speaks the numbers that were dialed. This verifies that you dialed the correct number and is especially
Model 201 Wiegand Touchpad Reader Installation Guide
Model 201 Wiegand Touchpad Reader Installation Guide P/N 460353001C 15AUG11 2011 UTC Fire & Security. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without
ENGS 32 Winter, 2003. Prototyping Methods
There s more on this in Scherz, Practical Electronics for Inventors. Solderless Breadboard or Plugboard This is what we ve been using in lab. Very fast to build and make changes. Works well with DIP ICs
XBee USB Adapter Board (#32400)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
Redesigned by Laurier Gendron (Aug 2006 ) Download this project in PDF. Horn circuit. Train Circuitry
Redesigned by Laurier Gendron (Aug 2006 ) Download this project in PDF Train Circuitry Horn circuit New Design After many comments by interested hobbyists not being able to obtain parts like the LM566
Martin County Amateur Radio Association. Nightfire Kits 1 LED Torch Kit 270016. Contents. Description
Nightfire Kits 1 LED Torch Kit 270016 1 Contents Nightfire Kits LED Torch Kit 270016... 1 Description... 1 Safety and Assembly of the kit... 6 Required and Useful Tools... 7 Assembly... 8 Checkout and
Total solder points: 67 Difficulty level: beginner 1 2 3. 4 5 advanced UNIVERSAL TEMPERATURE SENSOR K8067 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 67 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL TEMPERATURE SENSOR K8067 Ideal for connection to computer interface boards (K8000, K8055, K8047,..) ILLUSTRATED ASSEMBLY
SMD Soldering Guide by Infidigm
SMD Soldering Guide by Infidigm Purpose The purpose of this guide is to introduce SMD (Surface Mount Device) hand soldering. The guide is organized into different methods. Each method is used specifically
Fundamentals of Signature Analysis
Fundamentals of Signature Analysis An In-depth Overview of Power-off Testing Using Analog Signature Analysis www.huntron.com 1 www.huntron.com 2 Table of Contents SECTION 1. INTRODUCTION... 7 PURPOSE...
How To Make A Feedback Decoder For A Model Railroad
BMD16N version 1.2 Feedback decoder with 16 contacts for the S88-bus Compatible with a.o. Märklin Digital, Uhlenbrock Intellibox, Fleischmann Twin-Center and LDT HSI-88 Compatible with the s88-n standard
User s Manual. BNC Mini-High Res, 75 Ohm Termination Kit Connector Installation Guide (60-073-01)
User s Manual BNC Mini-High Res, 75 Ohm Termination Kit Connector Installation Guide (60-073-01) BNC Termination Kit Instructions This document is a compilation of Extron s instructions, together with
MAINS VOLTAGE DETECTOR K7101
With this device wires can be very easily checked for mains voltage. H7101IP-1 MAINS VOLTAGE DETECTOR K7101 VELLEMAN NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com
The RSGB Centenary Receiver Project Construction Manual
The RSGB Centenary Receiver Project Construction Manual Page 1 of 12 Introduction This project is intended for those new to radio construction. It is a fairly simple receiver for the 14MHz (20m) amateur
Application Note: PCB Design By: Wei-Lung Ho
Application Note: PCB Design By: Wei-Lung Ho Introduction: A printed circuit board (PCB) electrically connects circuit components by routing conductive traces to conductive pads designed for specific components
Your Multimeter. The Arduino Uno 10/1/2012. Using Your Arduino, Breadboard and Multimeter. EAS 199A Fall 2012. Work in teams of two!
Using Your Arduino, Breadboard and Multimeter Work in teams of two! EAS 199A Fall 2012 pincer clips good for working with breadboard wiring (push these onto probes) Your Multimeter probes leads Turn knob
GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102
H4102IP-1 GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 Practice the guitar without disturbing others. Features & Specifications Features: An electric guitar cannot be connected to just any amplifier
RGB Wall Washer Using ILD4035
ILD4035 Application Note AN216 Revision: 1.0 Date: RF and Protection Devices Edition Published by Infineon Technologies AG 81726 Munich, Germany 2010 Infineon Technologies AG All Rights Reserved. Legal
Cumbria Designs T-1. SSB/CW Filter kit (4.9152MHz) User Manual
Cumbria Designs T-1 SSB/CW Filter kit (4.9152MHz) User Manual CONTENTS 1 INTRODUCTION 2 2 CIRCUIT DESCRIPTION 2 3 ASSEMBLY 2 4 TESTING 4 The Steading Stainton PENRITH Cumbria CA11 0ES UK 1 Introduction
User Guide #0602. User Guide for IRDC3624 Evaluation Board using IRF8910 SO-8, dual MOSFET and 2x 22µF ceramic output capacitors.
User Guide #0602 User Guide for IRDC3624 Evaluation Board using IRF8910 SO-8, dual MOSFET and 2x 22µF ceramic output capacitors By Parviz Parto Table of Contents Page Description...1 Connections...1-2
Total solder points: 18 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL POWER SUPPLY 5-14DC / 1A K2570 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 18 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL POWER SUPPLY 5-14DC / 1A K2570 The easy way to power your projects. ILLUSTRATED ASSEMBLY MANUAL H2570IP-1 Features & Specifications
Kit 27. 1W TDA7052 POWER AMPLIFIER
Kit 27. 1W TDA7052 POWER AMPLIFIER This is a 1 watt mono amplifier Kit module using the TDA7052 from Philips. (Note, no suffix.) It is designed to be used as a building block in other projects where a
DC Circuits (Combination of resistances)
Name: Partner: Partner: Partner: DC Circuits (Combination of resistances) EQUIPMENT NEEDED: Circuits Experiment Board One Dcell Battery Wire leads Multimeter 100, 330, 1k resistors Purpose The purpose
A Versatile Audio Amplifier
A Versatile Audio Amplifier...built around the TBA 810 Integrated Circuit You can build a versatile audio amplifier for your workbench or for any other of your audio projects...with the TBA 810 IC (Integrated
APPLICATION NOTES: Dimming InGaN LED
APPLICATION NOTES: Dimming InGaN LED Introduction: Indium gallium nitride (InGaN, In x Ga 1-x N) is a semiconductor material made of a mixture of gallium nitride (GaN) and indium nitride (InN). Indium
ARRL Morse Code Oscillator, How It Works By: Mark Spencer, WA8SME
The national association for AMATEUR RADIO ARRL Morse Code Oscillator, How It Works By: Mark Spencer, WA8SME This supplement is intended for use with the ARRL Morse Code Oscillator kit, sold separately.
Controlling a Dot Matrix LED Display with a Microcontroller
Controlling a Dot Matrix LED Display with a Microcontroller By Matt Stabile and programming will be explained in general terms as well to allow for adaptation to any comparable microcontroller or LED matrix.