Lecture 4. Global System for Mobile Communications (GSM) Asad Ali

Transcription

1 Lecture 4 Global System for Mobile Communications (GSM) Asad Ali

2 GSM system overview GSM is a digital wireless network It provides a common set of compatible services and capabilities to all mobile users worldwide The basic requirements of GSM have been described in five aspects: Services: The system will provide service portability, that is, mobile phones can be used in all participating countries. The system will offer services that exist in fixed line networks as services specific to mobile communications Quality of service and Security: The quality of voice telephony of GSM will be at least as good as the previous analog systems over the operating range. The system will be capable of offering information encryption without significantly affecting costs to users who do not require such facility.

3 GSM system overview Radio frequency utilization: The system will permit high level of spectrum efficiency and state-of-the-art user facilities. The system will be capable of operating in the entire allocated frequency band and co-exist with the earlier systems using the same frequency. Network: The identification and numbering plans will be based on relevant ITU recommendations. Cost: System parameters will be chosen with a view to limiting the cost of the complete system in particular the Mobile Stations. The figure in the next slide illustrates the GSM architecture.

4 GSM architecture

5 GSM architecture

6 GSM architecture (2) MS Mobile Station Base Station Subsystem (BSS) BTS: Base Transceiver station BSC: Base Station Controller Network and Switching Subsystem (NSS) MSC: Mobile Switching center Registers: HLR (Home Location Register), VLR (Visitor Location Register, AuC (Authentication center), EIR (Equipment Identity Register) GMSC: Gateway Services Switching Center

7 GSM Frequencies GSM-900 Uplink: MHz (25 MHz) Downlink: MHz (25 MHz) Uplink - Downlink distance: 45 MHz FDMA Channels are 200 khz wide Use 124 pairs of channels TDMA 8 timeslots (connections) on each channel Theoretical 124*8 = 992 channels to use

8 Mobile Station (MS) The MS consists of two parts: Subscriber Identity Module (SIM) and the Mobile Equipment (ME) The SIM is protected by the Personal Identity Number (PIN) which is usually 4 digits in length To use the MS, the user is asked to enter the PIN If the number is not correctly entered in 3 attempts, the SIM is blocked and the MS cannot be used To unblock the SIM, the user is asked to enter the eight digit PIN unblocking key (PUK)

9 Mobile Station (MS) A SIM card is a small memory device which contains user specific information It can be taken out from one mobile and inserted into another In a GSM network, the SIM card identifies the user just like a traveler uses a passport to identify himself There is also a storage place for messages and store phone numbers A home operator issues a SIM card when the user joins the network by making a service subscription It also contains tools for authentication purposes.

10 The Base Station Subsystem (BSS) The BSS connects the MS and the Network and Switching Subsystem (NSS) It consists of two parts: Base Transceiver Station (BTS) Base Station Controller (BSC) The BTS contains transmitter, receiver and signaling equipment related to the air interface in order to contact the MS The BSC is responsible for switching functions in the BSS and it turn connected to an Mobile Switching Center (MSC) in the NSS The BSS also supports channel allocation/ release and handover management.

11 Network and Switching Subsystem (NSS) The NSS contains the MSC, HLR, VLR, AuC and EIR. It supports switching functions, user profiles and mobility management. Basic switching functions in the NSS are performed by the MSC User information relevant to the provisioning of services is kept in the HLR When an MS moves from its current location to a visited location, its location is registered at the VLR of that system. The VLR then informs the HLR of its current location The Authentication Center (AuC) is used in security data management for the authentication of users. The AuC maybe co-located with the HLR.

12 Network and Switching Subsystem (NSS) The Equipment Identity Register (EIR) is a database which stores all device identifications registered for a network As MSs are mobile, they can easily be stolen. With a valid SIM, anyone could use the stolen MS The EIR has a blacklist of stolen devices. The MSC is involved in the interworking functions to communicate with other networks such as the PSTN through the GMSC.

13 Mobile Switching Center (MSC) Responsible for controlling calls within the network An MSC acting as a bridge between a mobile network and other fixed networks is known as Gateway MSC (GMSC) The MSC is responsible for several important tasks Call control: The MSC identifies the type of the call, its origin and destination. It also sets up, supervises and clear connections. Initiation of Paging: Paging is the process of locating a mobile in case of a mobile terminated call (MTC) (a call to a mobile station). Charging: Collects charging information about the call such as the number of callers and the called subscribers, the time and type of transaction etc and transfers it to the Billing Center.

14 Home Location Register (HLR) The HLR is the most important database in a GSM network. It stores all user relevant information This comprises of International Mobile Subscriber Identity (IMSI), Mobile Subscriber ISDN number (MSISDN), user data (e.g. supplementary services). It also stores dynamic information such as the current location area (LA) of the MS, the Mobile Subscriber Roaming Number (MSRN), current VLR and MSC As soon as the MS leaves its current LA, the information in the HLR is updated. This information is necessary to localize a user in the worldwide GSM network. HLRs can manage data for several million users and it contains highly specialized databases.

15 What is IMSI, TMSI, MSISDN, MSRN, IMEI etc..? IMSI: International Mobile Subscriber Identity GSM uses the IMSI for internal unique identification of a subscriber IMSI consists of a mobile country code (MCC), the mobile network code (MNC), i.e. the code of the network provider and finally the mobile subscriber identification number (MSIN) TMSI: Temporary mobile subscriber identity The TMSI is assigned to an MS by the VLR. The TMSI uniquely identifies an MS within an area controlled by the given VLR. MSRN: Mobile Station Roaming Number Another temporary address that hides the identity and location of a subscriber is MSRN MSISDN: Mobile subscriber ISDN number The mobile number that a user is allocated.

16 What is IMSI, MSISDN, MSRN, IMEI etc..? The VLR generates this address on the request of the MSC and this is also stored in the HLR. MSRN contains the current visitor country code (VCC), the visitor national destination code (VNDC), the identification of the current MSC together with the subscriber number. The MSRN helps the HLR to find a subscriber for an incoming call. IMEI: International Mobile Equipment Identity The IMEI uniquely identifies the MS equipment. It is assigned by the equipment manufacturer. The IMEI contains 15 digits and carries Type Approval code (TAC): 6 digits Final Assembly Code (FAC): 2 digits Serial Number (SN): 6 digits A Spare (SP): 1 digit

17 Visitor Location Register (VLR) A VLR is integrated with an MSC It s a dynamic data base which contains information about subscribers currently being in the service area of an MSC/VLR such as: Identification numbers of subscribers Security information for authentication of the SIM card Services that the subscriber can use The VLR carries out location registration and updates. It means that when a mobile station comes to a new MSC/VLR serving area, it must register itself with the VLR, in other words, perform a location update. It s a temporary database and holds to information as long as the MS is in its serving area.

18 Authentication Center (AuC) Provides security information to the network so that we can verify the SIM card (authentication between the MS and the VLR) Supports the VLR work

19 Equipment Identity Register (EIR) The EIR is also used for security reasons. It is responsible for the IMEI checking (checking the validity of the mobile equipment) The EIR contains three lists: A mobile equipment in the white list is allowed to operate normally If we suspect that the mobile equipment is faulty, we can monitor the use of it. It is then placed in the grey list If the mobile equipment is reported stolen, or it is otherwise not allowed to operate in the network, it is placed in the black list.

20 Radio Interface The available frequency band is divided into two sub bands: UPLINK and DOWNLINK

21 Radio Interface FDM is used to separate both the uplink and downlink as shown below.

22 Radio Interface This makes it 124 pairs of 248 channels. Each of the 248 channels are additionally separated in time via a GSM TDMA frame, i.e. each 200 khz carrier is subdivided into frames that are repeated continuously. The duration of the frame is ms A TDMA frame is again divided into 8 GSM timeslots where each slot represents a physical TDM channel and lasts for 577 microseconds Each TDM channel occupies the 200 khz for 577 microseconds every ms.

23 Radio Interface Data is transmitted in small portions called bursts The figure in the next slide shows the so-called normal burst as used in data transmission inside a time slot. In the diagram, the burst is only microseconds long and contains 148 bits The remaining 30.5 microseconds are used as guard space to avoid overlapping with other bursts Filling the whole slot with data allows for the transmission of bits within 577 microseconds

24 Radio Interface

25 Radio Interface The tail bits (T) are a group of 3 bits set to zero and placed at the beginning and the end of a burst. They cover the periods of ramping up and down of the mobile's power. The user data bits corresponds to two groups, of 57 bits each, containing signaling or user data. The stealing flags (S) indicate, to the receiver, whether the data bits are data or signaling traffic. The training sequence has a length of 26 bits. It synchronizes the receiver, thus masking out multi-path propagation effects. The guard period (GP), with a length of 8.25 bits, is used to avoid a possible overlap of two mobiles during the ramping time

26 Logical Channels and Frame Hierarchy The air interface has two sorts of channels, i.e. physical channels and logical channels One channel is the highway that carries the signal traffic The other is the traffic that flows along the highway Which is the physical and logical channel in the next figure. Physical channel? Logical channel?

27 Logical Channels and Frame Hierarchy

28 Logical Channels and Frame Hierarchy Physical channel is the medium along which the information is carried For terrestrial interfaces, this is usually cable For the air interface, these are radio waves Logical channels comprise the information that is carried along the physical channel, that is, the traffic itself

29 Logical Channels and Frame Hierarchy A single GSM Absolute Radio Frequency Channel Number (ARFCN) can support up to 8 mobile users at the same time

30 Logical Channels and Frame Hierarchy 8 consecutive physical channels or time slots occupy the ARFCN for exactly one eighth of the time The 8 time slot sequence is called a TDMA frame Signals are carried in bursts from the MS to the BTS using one time slot per TDMA frame (shown in the next slide) Subsequent data bursts occupy the same time slots across successive TDMA frames Each time slot is a physical channel carrying varying number of logical channels from the MS to the BTS Each user occupies the same physical channel until it terminates the call or is handed over to another cell.

31 Logical Channels and Frame Hierarchy

32 Logical Channels and Frame Hierarchy Now we look into more detail on GSM logical channels GSM logical channels consists of Traffic Channels (TCH) and Control Channels (CCH) GSM uses TCH to transmit user data Two basic categories of TCHs have been defined, i.e. fullrate TCH (TCH/F) and half-rate TCH (TCH/H) TCH/F is 22.8 kbps TCH/H is 11.4 kbps For data transmission, rates of 9.6, 4.8 and 2.4 kbps can be used.

33 GSM Logical Channels There are two types of CCH associated with the TCH Slow Associated Control Channel (SACCH) Fast Associated Control Channel (FACCH) SACCH: A GSM control channel used by the MS for reporting signal strengths and quality measurements FACCH: Carries control information as shall be seen later Control channels in GSM are used to control medium access, allocation of traffic channels or mobility management and fall into three categories Broadcast Control Channels (BCCH) Common Control Channels (CCCH) Dedicated Control Channels (DCCH)

34 GSM Control Channels Broadcast Control Channels (BCCH) A BTS uses this channel to signal information to all MSs within a cell Information transmitted in this channel is, for example, frequencies available inside the cell and in neighboring cells. The BTS sends information regarding frequency via the frequency control channels (FCCH) and information about time synchronization via the synchronization channel (SCH) where both channels are sub-channels of the BCCH Downlink only Carries information about the network, mobile s present call and the surrounding cells The synchronizing channels carry frame synchronization information The Frequency control channels (FCCH) carries information regarding frequency synchronization

35 Broadcast Control Channels (BCCH)

36 Common Control Channels (CCCH) Bi-directional All information regarding the connection setup between the MS and the BTS is exchanged via the CCCH For call towards an MS, the BTS uses paging channel (PCH) for paging the appropriate MS (downlink) If an MS wants to setup a call, it uses RACH to send data to the BTS (uplink) gain access to the system The BTS uses access grant channel (AGCH) to signal an MS that it can use a TCH or SDCCH for further connection setup (downlink) PCH and AGCH are downlink but are never used at the same time Cell broadcast channel is used to transmit information such as traffic information to all MSs

37 Types of CCCHs

38 Dedicated Control Channels (DCCHs) Supported in GSM for dedicated use by specific MS Its consists of Standalone dedicated control channel (SDCCH) Slow associated control channel (SACCH) Fast associated control channel (FACCH) SDCCH: As long as an MS has not established a TCH with the BTS, it uses the SDCCH for signaling SACCH: Each TCH and SDCCH has a SACCH associated with it which is used to exchange system information, such as the channel quality and signal power level. FACCH: If more signaling information is needed to be transmitted and a TCH already exists, GSM uses the FACCH. The FACCH uses timeslots which are otherwise used by the TCH. This is necessary incase of handovers where the BTS and MS have to exchange data.

39 Types of Control Channels

40 GSM call origination (radio aspect) RACH (request signaling channel AGCH (assign signaling channel) SDCCH (request call setup) SDCCH message exchanges for call setup SDCCH (assign TCH) FACCH (complete assignment) MS BSS

41 GSM call origination (radio aspect) To initiate a call setup, the MS sends a signaling channel request to the network through RACH The BSC informs the MS of the allocated signaling channel (SDCCH) through AGCH The MS then sends the call origination request via SDCCH The MSC instructs the BSC to allocate a TCH for this call Then the MS acknowledges the traffic channel assignment through FACCH Finally, both the MS and the BTS tune to the TCH

42 Location Tracking and Call Setup The current location of an MS is maintained by a two-level hierarchical strategy with the HLR and the VLRs When a MS visits a new location, it must register in the VLR of the visited location The HLR must also be updated about this registration. To access the MS, the HLR is queried to find the current VLR of the MS The registration process of the MS moving from one VLR to another VLR is described in the following steps.

43 The MS registration process

44 The MS registration process Step1: The MS periodically listens to the BCCH broadcast from the BSS. If the MS detects that it has entered a new location area, it sends a registration message to the new VLR by using the SDCCH channel Step2: The new VLR communicates with the old VLR to get information about the MS. The new VLR then performs the authentication process to be described later Step3: After the MS is authenticated, the new VLR sends a registration message to the HLR. If the registration request is accepted, the HLR provides the new VLR with all relevant user information for call handling.

45 The MS registration process Step4: The new VLR informs the MS of the successful registration Step5: After step 3, the HLR sends a deregistration (cancellation) message to the old VLR. The old VLR cancels the record for the MS and sends an acknowledgement to the HLR for the cancellation.

46 Localization The HLR always contains information about the current location and the VLR currently responsible for the MS informs the HLR about location changes As soon as the MS moves into a location area of a new VLR, the HLR sends all user data to the new VLR Changing VLRs with uninterrupted availability of all services is also called roaming. Roaming can take place within the network of one provider, between two providers in one country, but also between different providers in different countries (international roaming). Typically people associate the word roaming with international roaming as it is this type of roaming that makes GSM very attractive: one device over 190 countries!

47 Localization To locate an MS and to address the MS, several numbers are needed: MSISDN: The only important number for a GSM user is the phone number. The phone number is not associated with a certain device but with the SIM, which is personalized for a user. The MSISDN follows the ITU-T standard E.164 for addresses as it is also used for fixed networks. This number consists of the country code, national destination code (NDC) (i.e. address of the network provider), and the subscriber number (SN).

48 Localization IMSI: GSM uses the IMSI for internal unique identification of the user. IMSI consists of a mobile country code (MCC), the mobile network code (MNC), and finally the mobile subscriber identification number (MSIN). TMSI: To hide the IMSI, which would give away the exact identity of the user over the air interface, GSM uses the 4 bit TMSI for local user identification. TMSI is selected by the current VLR and is only valid temporarily and within the location area of the VLR.

49 Localization MSRN: Another temporary address that hides the identity and location of the user is the MSRN. The VLR generates this address on request from the MSC and the address is also stored in the HLR. MSRN contains the Visitor Country Code (VCC), the visitor national destination code (VNDC), the identification of the current MSC together with the user number. All these numbers are needed to find a subscriber and maintain a connection with the MS.

50 Mobile Originated Call (MOC) Step 1: The MS transmits a request for a new connection Step 2: The BSS forwards this request to the MSC Step 3 and 4: The MSC then checks if this user is allowed to setup a call with the requested service and checks the availability of resources through the GSM network and into the PSTN If all resources are available, the MSC sets up a connection between the MS and the fixed network. This is illustrated in the next slide.

51 Illustration of MOC

52 Mobile Terminated Call (MTC) Step 1: The user dials the phone number of a GSM subscriber Step 2: The fixed network (PSTN) notices (looking at the dialed number) that the number belongs to a user in the GSM network and forwards the call to the GMSC Step 3: The GMSC signals the call setup to the HLR Step 4: The HLR now checks whether the number exists and whether the user has subscribed to the requested service and requests an MSRN from the current VLR Step 5: The HLR receives an MSRN Step 6: The HLR can determine the MSC responsible for the MS and forwards this information to the GMSC

53 Mobile Terminated Call (MTC) Step 7: The GMSC now forwards the call setup request to the MSC indicated. From this point onwards, the MSC is responsible for all further steps. Step 8: MSC requests the current status of the MS from the VLR Step 9 and 10: If the MS is available, the MSC initiates paging in all cells it is responsible for (i.e. location area) Step 11: The BTSs of all the BSSs transmit this paging signal to the MS Step 12, 13 and 14: If the MS answers, the VLR has to perform security checks Step 15 to 17: The VLR then signals to the MSC to setup a connection to the MS

54 Illustration of Mobile Terminated Call (MTC)

55 Illustration of Mobile Terminated Call (MTC)

56 Handover Scenarios There are two basic reasons for a handover which are: The MS moves out of the range of the BTS or a certain antenna of a BTS respectively. The received signal strength decreases continuously until it falls below the minimal requirements for communication. The wired infrastructure (BSC, MSC) may decide that the traffic in one cell is too high and some MS to other cells with a lower load (if possible). Handover maybe due to load balancing.

57 Handover Scenarios There are four possible handover scenarios in GSM Intra-cell handover: Within a cell, interference could make transmission at a certain frequency band impossible. The BSC could then decide to change the carrier frequency Inter-cell, intra-bsc handover: This is a typical handover scenario. The MS moves from one cell to another, but stays within the control of the same BSC. The BSC then performs a handover, assigns a new radio channel in the new cell and releases the old one

58 Handover Scenarios Inter-BSC, intra-msc handover: As a BSC only controls a limited number of cells, GSM also has to perform handovers between cells controlled by different BSCs. This has to be then controlled by the MSC. Inter-MSC handover: A handover could be required between two cells belonging to different MSCs. Now both MSCs perform the handover together.

59 Security in GSM GSM security is addressed in two aspects: Authentication and Encryption Authentication avoids fraudulent access and Encryption avoids unauthorized listening

60 Authentication Authentication is achieved by using a secret key, K i This value is stored in the SIM as well as the AuC and is unknown to the subscriber Authentication is based on the SIM which stores the individual key, user identification IMSI and the A3 algorithm. It uses a challenge response method The home system of the MS generates the 128 bit random number (RAND). This number is sent to the MS The SIM within the MS responds with a signed response (SRES)

61 Authentication The SRES generated by the MS is sent back to the home system and compared with the SRES generated by the AuC. If they are not identical, access request is rejected. If the SRES and RAND generated by the AuC are sent from the HLR to the visited VLR in advance, then SRES comparison is done at the VLR. The AuC generates the numbers for each IMSI and forwards this information to the HLR

62 Authentication For authentication, the VLR sends this RAND value to the SIM Both sides perform, the same function with the RAND and Ki, called the A3 algorithm The MS sends back the SRES generated by the SIM Visited VLR compares both values If they are the same, the MS is accepted otherwise rejected. The process of Authentication is illustrated in the next slide.

63 Authentication

64 Encryption To ensure privacy, all messages containing user-related information are encrypted over the air interface After the authentication process is complete, the MS and BSS can start encrypting by applying the encryption key, K c The encryption key is generated using the K i and a random value by applying the A8 algorithm. SIM in the MS and the network both calculate the same K c based on the random value MS and BTS can now encrypt and decrypt data using the A5 algorithm and K c

65 Encryption Like the A3 algorithm, A8 is specific to the home system. After the home system has generated Kc, this is sent to the visited system A5 is then used to encrypt and decrypt the data between the MS and the visited system. The process of Encryption is illustrated in the following slide.

66 Encryption