RADIOS RECOMMENDED: each team shall notify FUPS Officials of who is the spotter for each event.
|
|
- Noreen Jones
- 8 years ago
- Views:
Transcription
1 I. DISCLAIMER The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These rules shall govern the condition of all events, and by participating in these events, all participants are deemed to have complied with these rules. No expressed or implied warranty of safety shall result from publications of or compliance with these rules and/or regulations. They are intended as a guide for the conduct of the sport and are in no way a guarantee against injury or death to a participant, spectator, or official. The race director shall be empowered to permit reasonable and appropriate deviation from any of the specifications herein or impose any further restrictions that in his opinion do not alter the minimum acceptable requirements. No expressed or implied warranty of safety shall result from such alteration of specifications. Any interpretation or deviation of these rules is left to the discretion of the officials. Their decision is final. It is the responsibility of the teams and competitors to present a legal race vehicle for competition. Any vehicle that with illegal modifications that pass through technical inspection undetected will be disqualified immediately upon detection of the infraction. -1-
2 II. BASIC GUIDELINES A. SERIES reserves the right to update, modify, and/or delete rules at any time deemed necessary to insure safety, fair competition or any other reason that may be appropriate. B. Any interpretation or deviation of these rules is left to the SERIES officials. Any decision of and by SERIES Officials is final. C. Unsportsmanlike-like conduct can carry a minimum $ fine and/or suspension and/or loss of points. Any and all fines will be added to the point s fund at the end of the racing season. III. RULES AND SPECIFICATIONS The word STOCK used within this set of rules means as originally produced by the manufacturer for that make, model, and year of car with no altering or modifications. Top five cars after race will go directly to tech and scales. RADIOS RECOMMENDED: each team shall notify FUPS Officials of who is the spotter for each event. WHEELS: 1. All wheels shall be 15 x8 steel, no aluminum wheels. 2. Must install minimum ½ wheel studs and 1 lug nuts. 3. No air bleeders or Pop Off Valves allowed. TIRES: 1. Hoosier 750 Rights and lefts. 2. Must be stamped series approved tires. 3. Must meet tech approval. No Tire softening permitted. 4. No tire shall punch less than 50 on the durometer. 5. Cars must start the feature on the same tires they qualified on. 6. The Series will enforce the tire purchase rule of ROLL CAGE: 1. Roll cage design must be rounded steel tubing, minimum 1 3/4 OD, with a minimum wall thickness of.095. No Black Iron Pipe. 2. All roll bars around driver s area shall be padded. 3. Must have full roll cage with a minimum of 4 gusseted door bars on driver s side and minimum of 3 gusseted door bars on the right side. 4. May use 2 x2 or 2 x3 square tubing outside of the frame on driver s side. Must weld down bars to frame on right side of car. 5. May run minimum of 2 bars back to rear frame rails minimum of 1 ¾ OD steel tubing. 7. Front hoop ok, 1 ¾ OD steel tubing. 8. Front down bar must follow contour of front window post. No more than six inches behind window post. 9. Cross bracing is permitted. -2-
3 CRATE ENGINES: 602 Only Create Allowed. No Others! 1. Engine will be checked first time of competition for compliance. 2. Carburetor: Part Number Holley Only Spacer Plate allowed totals with gaskets. 4. GM Max of 160 pounds of compression. 5. May not use double roller timing chain & gear, non-adjusting. 6. Crate Engines will be checked like any other motor in accordance with the GM Tech Manual and by FUPS Tech Officials. Seals are NOT required. 7. No other changes allowed; this Engine will tech like all other FUPS Sportsman approved engines. 8. Crate Engines if found illegal will be toss on 1 st offense, 2 nd Offense owner/driver will be fined $ and loss of points. BLOCK for BUILT ENGINES: 1. Chevy 362 cubic in. max., Chrysler 360, Ford, 351 allowed. No Aluminum Blocks or Heads Allowed. 350 s must run 350 Heads. 2. Engine location: #1 spark plug hole even with or in front of ball joint. No engine set back tolerance!!! 3. You may clean up casting flaws in lifter galley and oil drains. No other grinding anywhere block allowed. 4. Screen kits allowed. 5. Block may be 2 or 4 bolt main caps; no splayed caps allowed. 6. Block deck may be resurfaced for square-ness not to exceed 0- deck height. 7. Piston may not extend out of block. 8. Fasteners Builder s choice. 9. May paint inside of block. CARBURETOR: 1. Must be Stock Holley 4412, 500 CFM 2 Barrel 2. Air Box Allowed 3. Carburetor spacer or total including gaskets. 0-Tolerance. 4. May remove carburetor choke plate. 5. May change power valve. 6. Any jet is allowed. 7. Must pass series or track gauge. 8. Any illegal carburetor will be confiscated and disposed of at FUPS Sportsman Series tech official s discretion 9. NO Electric Fuel Pumps Allowed. 10. Fuel supply line shall not run through driver s compartment. 11. Carburetor Fuel Bowl to face front of car. 12. Must run gasoline or track race fuel, no fuel additives allowed. 13. Minimum of 2- throttle return springs. VALVES: 1. Stock production or OEM replacements only. 2. May use one-piece stainless steel. 3. No lightweight valves allowed. 4. No tulip or back cut valves allowed. 5. No back facing. 6. Maximum Sizes: GM Intake 1.94 Exhaust 1.50 Chrysler Intake 1.92 Exhaust Ford Intake 1.94 Exhaust
4 7. Stock valve train only with the following exceptions: a. Three angle valve jobs ok. b. Poly Locks ok. c. Screw in Studs ok. d. Any valve spring may be used as long as spring seat remains stock diameter and is un-machined. Max outside diameter e. May use 7 degrees or 10 degrees steel valve locks. INTAKE MANIFOLD: 1. Any cast or Aluminum intake W/4.5 plenum height. 2. No porting or polishing, no coatings of any kind. 3. May run Eldebrock #2901 with single 1 1/16 gasket. 4. No Bowtie. 5. Max Spacer with gasket. CYLINDER HEAD: 1. Max. Compression is 10 to 1, No Bowtie Heads. 2. No porting, grinding, polishing, or gasket matching. 3. World Product S.R. #4360 or #4361, DART # or # , & RHS #12400 or #12407 heads are the only approved aftermarket Heads. Vortec Heads allowed. Closed Chamber Heads add 100lbs. 4. Last cut no more than 80 degrees on seat. 5. No angle milling. 6. No acid washing or sand blasting of ports. 7. Screw in studs and guide plates OK. 8. Spring retainers must be steel only, no aluminum or titanium. 9. No shaft mounted rocker assemblies, unless factory design. 10. Any cylinder head that has had casting numbers ground will be illegal. PISTONS: 1. Piston pin height must remain stock. 2. Any Flat Top or Dish Piston allowed. CAMSHAFT: 1. Any Hydraulic type cam allowed. Degree bushings permitted. 2. Stock type lifters, no roller or mushrooms. 3. Cam button and locking plate permitted. 4. Roller Rockers and Stud girdle permitted. 5. Poly Locks OK. 6. Rocker duration engine builder option. CRANKSHAFT: 1. Must remain stock for engine used. 2. Must be OEM or Stock replacement. 3. No Knife edged crankshafts. 4. Balancing permitted. 5. No lightweight crankshafts. 6. Must weigh a minimum 50lbs. for steel, 47lbs. for cast iron on 7. Track scales. -4-
5 RODS: 1. Any Steel Rod, minimum weight 1250gms. Piston/Rod assembly as pulled from motor. 2. Stock Length and weight for block used. 3. Balancing is permitted. 4. After market rod bolts OK. 5. Piston pin may be floating or press in. ENGINE MISCELLANEOUS: 1. May use cast iron exhaust manifold. 2. Headers Optional; Ok to wrap headers. Must extend past driver or passenger doors. 3. Stock HEI or single point ignition; Stock coil, Stock type module. NO MSD or similar spark intensifier boxes permitted. Optional Distributor; MSD-8365 may be used. 4. One 12 volt battery per car. 5. May use aluminum crank and water pump pulleys. 6. No electric water pumps. 7. Aluminum timing covers permitted. 8. Oil coolers are permitted. 9. High volume oil pumps are permitted. 10. Crate Engines, 7 Oil Pan permitted. 11. Aftermarket oil pump pickup is permitted. 12. Crank scraper or windage trays are permitted. 13. Solid motor mounts are permitted. 14. No high performance or turbo parts allowed. 15. Solid throttle parts only; no cables of any kind. 16. Must have fuel shut-off valve mounted and clearly labeled for easy access for Safety Crews. 17. Harmonic Balancers; stock type with SFI rating, no aluminum. 18. Starter must be Stock type or Mini Starter. No reverse mount allowed. 19. Aluminum Water Pump Allowed. 20. Must have removable plug in oil pan for inspection. 21. May use roller rockers and stud girdle. WEIGHT: 1. All cars must weigh a minimum of 3000 pounds after race. 2. Left side weight maximum will be 56% of the total weight. 3. No weight breaks for Crate Motors. ADDED WEIGHT: 1. Weight must meet all requirements, both total and left side bias, at the completion of any race or at any time. All weights will be made with driver sitting in driver s seat, with steering wheel in place, Hands on wheel and helmet in lap. 2. Any weight of any type added for any purpose, including but not limited to bringing up a car to the minimum restriction or adding ballast must be installed safely & secure. This installation is subject to inspection and approval of the Series Officials at any time. -5-
6 3. Weight must be secured with two 1/2 bolts and washers per 50lbs. 4. All weight pieces must be painted white and contain car number. 5. All added weight must be mounted to frame. No mounting on bumpers, firewall, floor pan, or within the driver s compartment. 6. Any loss of weight from car, for any reason, will result in disqualification. 7. No part of a car will be added back if a part is lost. 8. If FUPS Officials deem that a car has an advantage in any manner, They can add weight to said car for that event. RADIATOR: 1. Stock OEM or Aluminum. 2. Must be mounted in front of engine. 3. Plastic or metal fans only. 4. Absolutely no Anti-Freeze. If caught you will receive fine. 5. Cooling Fan Option: Electric or Fan. CAR TYPE: 1. Any American made car with a minimum of 105 factory wheelbase, which shall be stock for that car. Examples Camaro, Nova, Monte Carlo, Cutlass, etc. 2. Uni-body Cars: See Frame Rules. FRAME: 1. No High Performance (Corvette), Station Wagons, Trucks, or Convertibles. 2. May be fabricated from firewall, Full frame cars must keep 18 inches of right side Frame rail. If not to firewall add 50 lbs in front of firewall. 3. No holes cut to lighten frame. 4. Frame made be strengthen by Xing lb penalty if narrowed in front of flywheel. 6. Ground clearance minimum is 4 measured behind front tire and in front of rear tire. 7. Front cross member must remain original and in stock location. May be notched and boxed for fuel pump, headers & oil pan only. 8. May box in stock frame side rails. 9. May build motor for solid mounts. #1 spark plug must be even or ahead of left upper ball joint. 12 minimum from center line of crank shaft to the ground. 10. Engine must be centered between frame rails; 1 tolerance. 11. Crossmember must retain stock dimensions from bottom of cross member to lower control arm pickup points. If crossmember has been modified other than fuel pump area a 50 lb weight penalty will be added in front of flywheel. 12. UNIBODY ONLY: 1. All frame rails must remain stock for that year of car. May not be moved. LS frame offset Max. 16 excluding 4 for weight tray. 2. May be tubed from stock clip. 3. Roll cage must be mounted to frame rails. If frame rail on driver s side does not extend out to rocker panel then stock rocker panel must remain in place out on left side only. If not stock, you may build proper driver s box. 4. Adjustable shackles permitted on leaf spring cars, sliders ok. 5. Jacking Bolts permitted on coil spring cars. (Four) 6. Adjustable lowering blocks permitted. 7. No Carbon Fiber Springs 8. Leaf Springs, Chevy, Chrysler, or mono okay, Must be Stock lbs in front of flywheel.
7 -6- BUMPERS: 1. Stock Bumper not allowed. 2. Must be rounded on ends and braced back to frame. Absolutely no sharp edges on any piece of the bodywork or the Bumpers. All corners, edges, and protrusions must be rounded. May be braced back to the frame or cage with one inch pipe only. NO SOLID BARS. Bracing may not extend more than 6 past the point where it connects to the frame. 3. Rub Rails: (one per side) may be used. 1 square tubing or aftermarket Lexan. (Performance Bodies, 5 Star Bodies) 4. Bumper heights will be measured from ground to center of main bumper bar: a. Minimum 17 b. Maximum 19 c. Must fit covers see BUMPER RULE BODY: 1. Body may be Steel, Aluminum, or Fiberglass, No Carbon Fiber Bodies Allowed. 2. Roof May Be: Stock Steel, after market steel, or fiberglass. Absolutely no Carbon Fiber, Any excessive narrowing of the B and C posts may result in a weight penalty. Roof height must measure A minimum of 47 from ground to center of roof. 3. Driver side window opening from top of door to bottom edge of roof must be a minimum of Ground clearance must be a minimum of 4 body and frame, nose and skirt. 5. Full windshield mandatory, you may use minimum 1/8 Lexan for windshield. No Plexiglas or glass. 6. Rear window optional. 7. Offset bodies permitted considering that roll cage meets requirements. 8. Plastic nosepiece is mandatory. May use dirt plastic nose and fenders. 9. No roof rails. No rear window rails. 10. There must be no sharp edges on any piece of bodywork or bumpers. All corners, edges, and protrusions must be rounded. 11. An opening may be cut out of hood for air cleaner clearance. 12. Tailpiece is optional. 13. Hood is mandatory and must maintain OEM stock appearance. 14. Fiberglass hood permitted. 15. Must have permanent fasteners installed, minimum of either four hood pins or two hood pins and two hinges. 16. Hood must fit flat to fenders. 17. No car will be permitted to start the race without a hood. 18. Hoods lost during a racing accident are excused and the hood must be beyond repair before car may re-enter a race. Repair or replacement must be completed before next race. 19. Rear deck lid must open for inspection. 20. Air box cannot extend past width of radiator, no belly pans under nose piece. -7-
8 REAR SPOILER: 1. Non Adjustable Lexan or Aluminum Only. Maximum height 6, maximum Width Must be flat with no lip. 3. Spoiler may be braced on front or back. Front braces cannot be higher than spoiler. Track reserves right to have you remove any braces that do not conform. INTERIOR: 1. Driver s compartment must be completely sealed from fuel cell with minimum of 20-gauge steel. 2. May box interior with steel or aluminum. 3. All holes in firewall and floor pan must be covered with steel. 4. Rocker panels may be removed. 5. May run exhaust over right frame rail and out door. Must be covered with minimum 20 gauge steel. SUSPENSION: 1. Any steel body racing shock is permitted. No aluminum body, no external oil tanks on shocks, no remote mounted reservoir. No Adjustable Shocks allowed. 2. $ retail price limit on each shock. Example Carrera- 31&21 series: Pro Shocks- WB Series, QA1 50 Series and AFCO. 3. No more than one shock absorber per wheel. 4. Front & Rear shocks may be relocated. 5. Control arm bushing material optional. No offset bushing. 6. Front Lower Control Arm, must remain stock; stock location. 7. May use tubular upper A- Frames any length. Non Adjustable. Upper A-Frame mounts and Points Optional. 8. Stock type Sway Bar or Original Howe Design only, no heim joints. 9. Shocks may be mounted to lower A-Arms. 10. Center- link of steering linkage may be spaced upward or downward. Aftermarket Center Link OK. 11. Ball joints: non adjustable or take apart ball joints allowed. May run different lengths on ball joints. 12. Stock OEM Spindles only, may interchange within manufacture only. Safety Hubs are permitted, no aluminum. 13. Leaf Spring Chassis may not use fiberglass or composite. 14. Any Steel Racing Spring Is Allowed. 15. Three Link Suspension permitted. STEERING: 1. Steering Box must remain in Original Stock Location. 2. No Rack And Pinion allowed, original OEM must be used. 3. After-Market power steering pumps allowed and must be driven off Crankshaft pulley. 4. Steering Wheel Disconnect Is Mandatory. 5. Collapsible Steering Shaft is allowed. 6. Pittman arm, drag link, inner tie rods are to remain stock. Outer tie rod ends may be replaced with heims, and may be spaced up or down for bump steer. -8-
9 BRAKES: 1. May run disc. 2. May use proportioning valve. 3. Brake lines must be OEM or steel braided only. 4. All cars must be equipped with four wheel brakes. 5. No Aluminum calipers allowed on front. Howe calipers OK. Single Piston calipers only. 6. May use aftermarket Brake pedals and master cylinder. 7. No drilling of rotors. READEND: 1. Stock OEM or Ford 9 Inch. 2. Must be locked via welding or solid spool. Full spool ok. 3. Floaters Permitted. No polishing or lightening of the tubes. 5. Quick Change Permitted. Steel Tubes Only. No Wide Fives. No Chamfered tubes on any housing. All above rules apply to Quick Change s also. 6. No Posi, Lockers, Gold Tracks, or Tru Tracks are permitted TRANSMISSION: 1. Stock OEM 3&4 Speeds only no automatics. 2. Two forward gears must be in working order with reverse. 3. Stock Clutch minimum 10 Solid hub clutch ok. Must have pad or full circle. 4. May use heavy-duty replacement pressure plate and disk. No aluminum allowed. 5. Flywheel-standard transmission any stock flywheel the same make as the car. No Light Weight Parts: 10,000 RPM etc All flywheels will be weighed on Track scales. Fly wheel weigh minimum of 14 pounds. 7. Standard transmission must use shatter proof bell housing. 8. After market shifters permitted hole in bell housing for inspection drive-shaft safety loops mandatory. Within 15 of front U Joint. 11. Drive shaft must be painted white, add car number. No Aluminum Drive Shafts Allowed. No carbon fiber. 12. May use hydraulic release bearing and push pull slave cylinder. 13. Cars with 7 ¼ Multi Disc clutch will be required to weigh 3100lbs. and 55% Left Side. No clutch smaller than 7 ¼ will be allowed. FUEL-FUEL CELL: 1. Approved Racing Fuel Cell with an aluminum 20 gauge Steel Can must be used. And securely installed with series approved mounting frame. 2. No aluminum or boat tanks. 3. Maximum 22 gallon fuel cell. 4. A firewall made of at least 20 gauge metal must be installed between driver and fuel cell. 5. Must have rear cell protection bar of 1.75 with 095 wall Tubing extending below the rear of the frame and at least ½ below the bottom of the fuel cell and cover the width of the fuel cell. Must be minimum of 9 off the ground.
10 -9-6. Must have foam and roll-over valve in vent. 7. Only one fuel cell line permitted to transport fuel from fuel cell to fuel pump. Do not run fuel line through driver s area. 8. No Additional fuel cells or fuel containers permitted. 9. No Electric Fuel Pumps. 10. Regular Pump Gas No Additives or Race Gas only. Track Approved. 11. No Trick Additives Allowed. No Alcohol. 12. No Fuel Cooling Devices Allowed. 13. Racing fuel will be available at the race track. SAFETY ITEMS: 1. Seat Belts shall not be older than three years of Date of Manufacture. 2. Drivers Window Nets shall not be older than three years of Date of Manufacture. They shall be a Quick Release type, with a Minimum of 26 wide X 16 high with a rating of SFI 27.1 Spec. 3. Drivers Fire Suit shall be free of any holes or tears. 4. Drivers Helmet & Racing Gloves shall not be older than three years of Date of Manufacture. 5. On board Fire Bottle must be up to date and certified. III. OFFICIAL DECISIONS: 1. Any situation not specifically covered in these rules will be acted upon by the official or SERIES officials in charge at the time, whose decision will be final and binding on all, participants. 2. Any disagreement over technical questions or operations will be resolved by SERIES officials. When their decision is rendered, such decision is final and binding. 3. Continuous developments in racing may necessitate changes which cannot be anticipated at the time rules are formulated. If necessary, rules may be updated, changed, deleted or added to at the discretion of the officials. 4. At certain events, to encourage participation of local competitors, the officials may alter the rules for those cars to try and create a level playing field for cars that might fall outside of the normal rules. Official s decisions are final. Membership Fee; In order to compete in any FUPS event for points or contingency awards, drivers and car owners must purchase a Florida United Promoters Series $ membership. A owner/driver must register a number with the series. Any member who permits another person to use his or her membership card for entry will be subject to a fine of $ and possible suspension and loss of points. If driver and owner are the same, one membership per car shall be allowed. Awards & Contingencies: Only FUPS Members who participate in at least 80% of all races held shall be eligible for any contingencies, end of the season awards, point monies, etc... You must attend the season ending banquet to receive any prizes, point money, awards etc. Protest Fee; only a FUPS Member may post a protest of another competitor. Protest fee is $1, for an engine tear down.
11 -10- IV. RACE PROCEDURES AND GENERAL CONDUCT GUIDELINES DRIVERS MEETING: 1. SERIES Officials will hold a Drivers meeting at each event. At this meeting all new or special information that may vary from the rulebook will be announced, and then be considered official. 2. A roll call will start each meeting. 3. The driver, crew chief and spotter from each team are required to attend each drivers meeting. 4. Failure of the driver, crew chief or spotter to attend the meeting will result in the driver starting in the rear of the field regardless of their qualifying time. QUAILIFYING PROCEDURES: 1. The order of events, including qualifying order will be posted at the Infield Tech Building and around the speedway. This information shall be posted at each FUPS Event it is each team s responsibility to follow & stay on time with said procedures. 2. Qualifying order, if applicable, will be determined by team preference based on the order of entries received at the SERIES office. (For example, the first entry received will get first pick of position in qualifying order and so on.) 3. Teams will have one chance to qualify. Once the car has taken the green flag their attempt has started. 4. The number of cars that will be inspected will be the choice of SERIES Officials. 5. No driver may attempt to qualify more than one car for the same event. 6. Any car not clearing post-qualifying inspection will have their time revoked and moved to the bottom of the order. 7. When two or more cars have duplicate times, the tiebreaker will be to revert back to their other lap. 8. SERIES Officials reserves the right to add 2 starting provisional, they must be FUPS Members. The series director & track owner shall have the final decision. RACE PROCEDURES: 1. All drivers must be on time and lined up for the main event or heat race they are to compete in. 2. Once the green flag has been displayed the race has started, no driver may change cars or use a backup car. 3. The Starter will control all starts. 4. All restarts will be double file with lead lap cars only. The starter will start the event at the designated start point. (SEE #20) 5. The free pass will be given to the first car one lap or more down At the caution flag. At which point the driver will be instructed to pass the pace car and line up at the end of the lead lap cars (See #20) 6. The free pass will only be used when there have been two laps of green flag racing consecutive. (See #20) 7. The free pass will not be given to any driver who brings out the caution flag, The free pass will not be given inside of ten (10)
12 laps remaining in the event. (SEE #20) All cars involved in an accident will be sent to the rear of the field on the restart. The term involved is at the discretion of SERIES officials. 9. Cars must report to tech area or victory lane as directed by SERIES officials. 10. Teams must not go on the racetrack for any reason. All repairs must be performed in pit area. 11. No car may pass the pace car or race leader unless instructed by tour officials. Any car illegally passing the pace cars or race leader will be assessed a 1 lap penalty. 12. No car will be allowed to continue in the race event should series officials deem the car is a hazard to other competitors or race fans. 13. Any driver who attempts to bring out a caution or intentionally causes a caution will be assessed a 1 lap penalty. 14. Cars must take the checkered flag on the racetrack in order to claim the win. Any rain out or stopped event because of track conditions or curfew at one lap past half way will be considered a complete race. 15. Any car not obeying the stop and go sign on pit road will be black flagged and return to the pits for a Stop and go penalty. 16. Cars must maintain a reasonable safe speed while in the pit area. 17. All race procedures are subject to judgment calls by series officials, as they may deem necessary. These judgment calls are considered final and are not eligible for appeal. 18. All cars must be able to maintain a minimum lap time of no less than 2 seconds a lap less than the leader. In the event that a car cannot maintain a minimum speed they will be sent to the pit area for the remainder of the event. 19. Any car involved in 3 cautions will be sent to the pits for the remainder of the event. 20. The SERIES Officials may or may not utilize double file restarts or free pass, as noted above, specifics will be addressed in the drivers meeting accordingly. INSPECTION: 1. All vehicles will be inspected during the course of the event at the discretion of the SERIES tech director. All Inspections will be performed as designated by the tech director and may vary from event to event. 2. Cars, parts and/or equipment will not be considered as having been approved by having passed through inspection at any time or number of times unobserved or undetected. 3. Rules are No Tolerance unless specified. Failure to comply with SERIES rules may result in disqualification from qualifying position, finishing position or the event entirely. 4. All SERIES approved weighing, measuring, testing devices and procedures used by technical officials are the standard that determines a vehicle compliance with SERIES rules and regulations. No other equipment or device may be used unless approved by the SERIES tech director. The decision of rules infractions during post qualifying or post technical inspections as imposed by tech
13 director shall be final. 5. SERIES officials reserve the right to confiscate any illegal and or unapproved part(s) Any use of components utilizing mercury shall be deemed to render the vehicle ineligible to compete in the event and such violation shall be reported to the proper authorities. 7. SERIES officials reserve the right to impound the racecar at any time. 8. All Florida United Promoters Series approved engines will be confiscated as one piece and sent to a FUPS approved engine builder for tear down if needed. The Series will do it s best to complete inspection of an engine on the same date as the FUPS race. 9. If the competitor being protested is legal, that competitor will receive the entire amount of the protest fee. If the competitor being protested is illegal, the entire protest fee will be returned to the competitor filing the protest. The illegal parts, engine, etc. will become the property of FUPS and not returned to the competitor found illegal. 10. The decisions made during the protest and the conduct in which the protest is handled is at the sole discretion of the SERIES tech director. PENTALTIES: 1. Penalties for violation of SERIES rules are determined by the gravity of the violation and its effect on the fairness of competition, the orderly conduct of the event and the interest of stock car racing and the series. Such penalties may include, but are not limited to, Disqualification, Suspension of a membership or license privileges, fines and or loss of points. The series director may use the following as guidelines for imposition of penalties in the situations described below, but these guidelines shall not limit the authority of the series Officials. 2. Any competitor that performs an act or participates in actions deemed by any SERIES official as detrimental to automobile racing or to series, fine of at least $ and competitor may also be sentenced to suspension and/or loss of points. 3. Any competitor who permits anyone else to use his/her membership for entry; Fine of least $500.00, and/or loss of points. 4. Any competitor who signs the release sheet or competitor pit permit for anyone else; a fine of at least $500.00, and/or suspension, and/or loss of points. 5. Any competitor who assaults or threatens to do bodily harm to any SERIES Official or persons serving under their direction; a minimum fine of $1,000.00, and/or suspension, and/or loss of points, and shall be removed from the venue by the local Law Agencies. 6. Any competitor while participating in an SERIES event partakes of any alcoholic beverage, stimulating, depressing or tranquilizing drugs or is otherwise under the influence; will result in a minimum fine of $2, and suspension and loss of points. DON T DO IT! 7. Any competitor who participates in fights in the pit area, or on the premises; a minimum fine of $ , and/or suspension, and/or loss of points, suspension and shall be escorted out by the local Law Agencies. 8. Any car found to have traction control (working or not); a minimum fine of $5, and loss of points for the year. 9. All drivers will be held accountable for the action of their crew, crew chiefs and any other family members or persons signed in under said driver/owner at all times.
14 RACE & PIT PROCEDURES PENALTIES A. Rear of the field Involved in the accident or stopping on the track resulting in caution. 2. Speeding through the pit area. B. Stop & go Penalty 1. Jumping the start or restart. 2. Run the stop & go sign on pit road. 3. Start out of position. C. Lap(s) or time penalty 1. Unauthorized pass of the pace car. 2. Failure to obey Officials or flag man. 3. Intentionally causing a yellow flag. D. Black Flag 1. Work on car while on the track. 2. Ignore the black flag. 3. Rough or reckless driving. 4. Actions deemed detrimental to auto racing. APPEALS: 1. A car owner or driver who is a FUPS Member may file an appeal against any penalty or fine imposed by the SERIES Race Director, provide that the individual submits intent to appeal letter to the Race Director with three (3) days of the penalty notice. 2. Appeals must be in writing and accompanied by the non-refundable appeal fee of $1, The Board of appeals shall be responsible for the timely and orderly disposal of such appeals. The board shall be comprised of competitors or Officials at the discretion of the series director. The time and date of such hearing will be as soon as possible at the Race Director s sole discretion. 4. Three members shall constitute a quorum 5. The hearing will be conducted in the manner best suited to the relevant facts. 6. The appellant may file a final appeal against the SERIES Commissioner. She/he may review information concerning the appeal and the decision may be based on that evidence or may hold another hearing. 7. Neither the board nor the Commissioner shall order an event to be rerun. 8. Race procedure calls are considered judgment calls and are not eligible for appeal
E-Mail- info@midvalespeedway.com--- Track 330-339-3977
The following rules are set as a guide, and are in no way a guarantee against injury or death to participants, or others. If there are any concerns not covered in these rules, consider any altercations
More informationMonster Mini Stock Assn rules for 2015
Monster Mini Stock Assn rules for 2015 *note 2 engine combinations* BODY - stock auto only may have complete aluminum body inner panel may be removed rear of car must be closed - no holes or flaps to meet
More informationLangley Speedway 11 Dale Lemonds Drive Hampton, VA. 23666 (757) 865 RACE(7223)
Langley Speedway 11 Dale Lemonds Drive Hampton, VA. 23666 (757) 865 RACE(7223) www.langley-speedway.com 2015 SUPER STREET DIVISION PERSONAL SAFETY EQUIPMENT: Each competitor is solely responsible for the
More informationSlide the new steering column shaft through the steering column from the driver compartment.
Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.
More informationSouthern Pro Am Truck Series Rules - Update 4/15/2016
Southern Pro Am Truck Series Rules - Update 4/15/2016 It is free to become a Southern Pro Am Truck Series member, you can pre-register online at www.driverseatracing.com or register at a Southern Pro Am
More information2016 Price Sheet. Custom Built Replacement Chassis
2016 Price Sheet Custom Built Replacement Chassis 5557 Chevy Car Direct Replacment Chassis 15,895 5362 Corvette Direct Replacment Chassis 15,895 5557 Chevy Car Pro Street Chassis 16,895 5362 Corvette Pro
More informationTHE PIT @ VIRGINIA MOTOR SPEEDWAY MUD BOG MUD SLING
THE PIT @ VIRGINIA MOTOR SPEEDWAY MUD BOG MUD SLING Location: U.S. RT 17, 20 miles South of Tappahannock, VA, 8 Miles North of Saluda, VA at Virginia Motor Speedway. Gates Open: 9am Registration: 9am 11am
More information1/29/2008 DR70. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43
DR70 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43 CYLINDER & CYLINDER HEAD 1 DR70-001 883099044472 CYLINDER 1 1 2 DR70-002 883099044489 GASKET, CYLINDER 1 1 3 DR70-003 883099044496
More informationDR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002 842645048173 GASKET, CYLINDER 1 1 3 DR90-003
More information1/29/2008 DR50. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45
DR50 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR50-001 842645074424 CYLINDER 1 1 2 DR50-002 842645074431
More informationDR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002
More informationFrom the Smallest Part... ...to Turn-Key Rods!
From the Smallest Part... Price: $3.00...to Turn-Key Rods! 32 Ford Coupe 34 Ford Cabriolet 34 Ford California Kid Corbin Rods features the very best fiberglass bodies and chassis at the lowest prices!
More informationS&W Race Cars and Components, Inc.
S&W Race Cars and Components, Inc. 11 Mennonite Church Road Spring City, PA 19475 TECH & INFORMATION: 610-948-7303 ORDERS: 1-800-523-3353 OFFICE FAX: 610-948-7342 E-Z INFO FAX 610-792-1234 CAUTION!!! -
More informationBR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > GOKART > BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM) BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
More information2016 4-Cylinder Pro- 4 Rules
2016 4-Cylinder Pro- 4 Rules $1000 fine for tire soak $100 fine for antifreeze COMPETING MODELS Competing models for cars and station wagons eligible are 1971 and later: American Motors Spirit Ford Thunderbird
More informationMcGee's Towing & Recovery 4 CYLINDER FIGURE 8 COMPETITION ESSEX COUNTY FAIR PO BOX 431 WESTPORT NY, 12993 AUGUST 13, 2016
McGee's Towing & Recovery 4 CYLINDER FIGURE 8 COMPETITION ESSEX COUNTY FAIR PO BOX 431 WESTPORT NY, 12993 AUGUST 13, 2016 $1,100.00 PURSE 1st place. $500.00 2nd place. $300.00 Heat winners.$50.00 2nd place
More information2015 OTP truck rules page 1 of 6
2015 OTP truck rules page 1 of 6 A. Stock 2wd under 5,000 lbs. B. Stock 4wd under 5,000 lbs. C. Stock 4wd small block under 6,000lbs. D. Stock 4wd big block under 6,000lbs E. Super stock 2wd under 4,000lbs.
More informationMUDDY MOTORSPORTS PARK RULE BOOK. Updated 2015
MUDDY MOTORSPORTS PARK RULE BOOK Updated 2015 General Rules 1. All spectators and crew members must be behind the crowd control fence. 2. Only track officials and one crew member will be on the track for
More informationDR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH) DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX
More information1/29/2008 DR125 / DR150. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55
DR125 / DR150 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55 CYLINDER HEAD ASSY. 1 125-001 883099006937 CYLINDER HEAD COVER 1 1 2 125-002 883099006944 BOLT M6X28 2 3 3 125-003 883099006951
More information2012 CHARGER DIVISION RULES AND REGULATIONS
1/23/12 2012 CHARGER DIVISION RULES AND REGULATIONS ALL PARTICIPANTS MUST ADHERE TO ALL THESE RULES IMPORTANT NOTE: MUFFLERS ARE MANDATORY AT RIVERHEAD RACEWAY LICENSE: -All drivers must take out a NASCAR
More informationTRANSMISSION INSTALLATION CONTENTS
A Regal Beloit Company TRANSMISSION INSTALLATION CONTENTS RICHMOND 6-SPEED AND SUPER STREET 5-SPEED WITH OVER DRIVE TRANS AM, CAMARO, CHEVELLE, GTO, CUTLASS, WITH T-10/MUNCIE....2 RICHMOND 6-SPEED 1963
More information2016 DARTS Rules Desoto All-Pro Race Trucks Series
2016 DARTS Rules Desoto All-Pro Race Trucks Series In the event we need to clarify any rules, we will do so in RED and make a post of facebook. Qualifying Procedures: 1. The driver that qualifies the truck
More informationDR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Parts Lists - DR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PR... Page 1 of 25 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR125 and DR150 Hensim Dirt
More informationMOTOR VEHICLE MECHANIC REPAIR CATEGORIES
Chapter 8: Motor Vehicle Mechanic Repair Categories Page 1 CHAPTER 8 MOTOR VEHICLE MECHANIC REPAIR CATEGORIES Section 8-1 REQUIREMENT Section 10 of the Motor Vehicle Service and Repair Act (MCL 257.1310)
More informationAUTOMOBILE MECHANIC STUDENT INTERNSHIP SKILLS LIST Provo School District
AUTOMOBILE MECHANIC STUDENT INTERNSHIP SKILLS LIST Provo School District Repairs and overhauls automobiles, buses, trucks, and other automotive vehicles: Examines vehicle and discusses with customer or
More informationMAN - MERCEDES - BENZ
SAYFA: 1 10100 10102 10103 355 353 06 15 355 353 03 15 346 353 08 15 AXLE GEAR AXLE GEAR AXLE (WITH BUSHING TYPE) (WITH BUSHING TYPE) (WITH BUSHING TYPE) 2521 2517-2521-2622 10104 10105 10106 308 350 00
More information2016 Ford County Fair
2016 Ford County Fair Demolition Derby Saturday, June 25th 2016 at 6:00 PM PITS open at 2:00pm Ford County Fairgrounds Melvin, Illinois Entry Fee is $30.00 for Cars and Trucks ** Special event entry is
More informationREMOVAL AND INSTALLATION
303-01C-1 REMOVAL AND INSTALLATION Engine Body On Special Tool(s) Adapter For 303-D043 303-D043-02 or equivalent Special Tool(s) 303-01C-1 Turbocharger Lifting Bracket 303-1266 Wrench, Fan Clutch Nut 303-214
More informationC O N T E N T S 1 ABOUT THIS PARTS LIST... 2 ENGINE GROUP... 3 3 CONTENTS-FRAME GROUP
C O N T E N T S 1 ABOUT THIS PARTS LIST... 2 2 CONTENTS-ENGINE ENGINE GROUP ENGINE GROUP... 3 3 CONTENTS-FRAME GROUP FRAME GROUP... 5 4 ENGINE PARTS LIST... 9 5 FRAME PARTS LIST...37 1 ABOUT THIS PARTS
More informationContents. Description Page Description Page
Contents Description Page Description Page Auger Housing Assembly 1 Muffler 18 Handle and Control Assembly 3 Fuel Tank r Assembly 19 Engine and Drive Assembly 5 Clutch Retarder 20 Cylinder Head 7 Retarder
More informationExtended Protection Plans for New and Pre-Owned Vehicles
Extended Protection Plans for New and Pre-Owned Vehicles Extended Protection you can count on from Old Republic Insured Automotive Services, Inc. (ORIAS) Your vehicle is a major investment. Next to your
More informationUnited Late Model Association
United Late Model Association www.ulmaracing.com / ULMA, P.O. Box 794, Moberly, MO 65270 / unitedlatemodelassociation@hotmail.com 2015 Rules Effective January 1, 2015 Association officials reserve the
More informationCOVERED. WE VE GOT YOU H-D EXTENDED SERVICE PLAN GET TO KNOW THE HDFS FAMILY: ASK YOUR DEALER FOR MORE INFORMATION. www.hdfsi.com
H-D EXTENDED SERVICE PLAN www.hdfsi.com WE VE GOT YOU COVERED. GET TO KNOW THE HDFS FAMILY: Harley-Davidson Insurance Harley-Davidson Extended Service Plan Harley-Davidson Debt Protection Plan Harley-Davidson
More information2011-14 F250 6 RADIUS ARM KIT
92154000 Thank you for choosing Rough Country for your suspension needs. 2011-14 F250 6 RADIUS ARM KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
More informationNon Sanctioned Truck & Tractor Pull Rules
Non Sanctioned Truck & Tractor Pull Rules No person or group of persons has the authority to override the Rule Book to allow an illegal vehicle to pull in any class under any circumstances. Event Procedures
More informationRail 001 112 2 Canvas, folding top 001 101 3 Rear panel 001 102 4 Stip in window, left 001 106 dto. right 001 107
U 411 1 Rear view mirror, round, metall 13cm Ø 002 045 2 Raised airintake 002 060 3 Side panelling, front, left 002 030 Side panelling, front, right 002 031 4 Panelling left 002 051 dto. right 002 052
More information46431x92A Garden Tractor (1998) Page 1 of 16 Body Chassis
46431x92A Garden Tractor (1998) Page 1 of 16 Body Chassis 46431x92A Garden Tractor (1998) Page 2 of 16 Body Chassis 1 092546E701 Bracket, Seat 2 091963 Z Plate Assembly, Switch 3 164X26 Spring, Compression
More informationMUSTANG II IFS COMPLETE PARTS PACKAGE
MUSTANG II IFS COMPLETE PARTS PACKAGE Your Southern Rods & Parts Mustang II IFS Parts Package contains the following items: 1 pr) Upper Control Arms (2023) 1) Upper Arm Bolt Kit (MP-001-A) 1 pr) Lower
More informationWynn s Extended Care
Wynn s Extended Care Every car deserves to receive the very best care... especially yours. How Do You Keep Your Reliable Transportation Reliable? Count on Wynn s Because Wynn s has been caring for cars
More informationReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD
SAFETY WARNING: recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks
More information356 CHECKLIST ELECTRICAL: CHASSIS:
356 CHECKLIST ELECTRICAL: Headlights hi/lo beam Taillights Running lights Turn signals Brake lights License light(s) Fog lights Reverse light Horn Dome lights Dash lights Temp guage Tank level guage Tachometer
More informationKobelco Extended Warranty Program. www.kobelco-europe.com
Kobelco Extended Warranty Program www.kobelco-europe.com Kobelco Extended Warranty is a convenient, value added way to give your Kobelco customers added security and peace of mind. Benefits of the Kobelco
More informationStreet-Lynx. Reilly MotorSports, Inc. Installation Manual
Street-Lynx By Reilly MotorSports, Inc. Installation Manual 1 1- Begin by removing your original rear suspension disconnect your brake lines, E-brake cables, and remove the driveshaft. To prevent fire
More informationCOVERING MILLIONS Preferred Protection Plan, a Service Group Company www.sgifs.com PO Box 26830, Austin, TX 78755-0800.
COVERING MILLIONS Preferred Protection Plan, a Service Group Company www.sgifs.com PO Box 26830, Austin, TX 78755-0800. 1-877-565-0816 PPP-308 0903 rev 0408 BENEFITS New and Pre-Owned Vehicles Preferred
More informationUDOT RPMS VEHICLE RECORDS, PREVENTIVE MAINTENANCE & SURVEILLANCE
UDOT RPMS VEHICLE RECORDS, PREVENTIVE MAINTENANCE & SURVEILLANCE VEHICLE RECORDS AND PREVENTIVE MAINTENANCE Prepared by: UTAH DEPARTMENT OF TRANSPORTATION OFFICE OF PLANNING AND PROGRAMMING IN COOPERATION
More informationInstallation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5
INSTALLATION GUIDE Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 Take every precaution to make this installation a safe procedure. Make safety the number
More informationMake sure all tubes are installed to your satisfaction BEFORE finish welding!!
INTRODUCTION: This S&W Roll Bar or Roll Cage performs both a safety and performance function. As a safety device, the main hoop of the cage protects the driver from impact. The rear braces and side bars
More informationTRANS-05, Torque Tube Removal, Rebuilding, and Installation
TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket
More information2010 APPLICATION REFERENCE GUIDE
2010 APPLICATION REFERENCE GUIDE INDEX QUALITY POLICY 2 ERGO ASSIST STANDARD 4-13 CUSTOM 14-18 END EFFECTORS 19-24 LIFT ASSIST 25-41 FIXTURED TOOLS 42-53 FIXTURES 54-63 ASSEMBLY TABLES 64-72 CARTS/ DUNNAGE
More informationSLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3
PART #50190 SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER
More informationOCEAN SPEEDWAY. 4 Banger TECHNICAL RULES Updated 02-05-2016
OCEAN SPEEDWAY 4 Banger TECHNICAL RULES Updated 02-05-2016 Prentince Motorsports Group. 8070 Soquel Drive, Suite 120 Aptos, CA 95003 Weekend Race Hotline: 831-662-WINN (9466) Business office 1-855-410-RACE
More informationBSA Goldstar Parts - Price List April 2016. 65-1137 Exhaust Lifter Cable 15.00. 65-1163 Exhaust Lifter Cable Holder S/S 9.00
Rocker Boxes 65-1137 Exhaust Lifter Cable 15.00 65-1163 Exhaust Lifter Cable Holder S/S 9.00 2-443 Exhaust Lifter Cable Holder Nut S/S 0.50 65-401 Exhaust Lifter Spindle Felt 2.00 65-387 Exhaust Lifter
More information6-years/75,000 miles Comprehensive coverage Subsequent Owner Warranty $100 Deductible
LINCOLN PREMIER LIMITED WARRANTY 6-years/75,000 miles Comprehensive coverage Subsequent Owner Warranty $100 Deductible Comprehensive Coverage Because Lincoln has always been a brand you can trust and respect,
More informationILLUSTRATED PARTS LIST
TW400 WITH 390cc HONDA ENGINE 390cc 2 WHEEL DRIVE UTILITY VEHICLE ILLUSTRATED S LIST 390cc 2WD B O D Y D I A G R A M 390cc 2WD F R A M E D I A G R A M 390cc 2WD D R I V E T R A I N D I A G R A M DESCRIPTION
More informationBUGGY SETUP GUIDE. Volume GOKARTSUSA GY6 150, CN250. Buggy Setup Guide
BUGGY SETUP GUIDE Volume 1 GOKARTSUSA GY6 150, CN250 Buggy Setup Guide GY6 150, CN250 DUNE BUGGY Buggy Setup Guide GOKARTSUSA.COM 2000 Highway 50 S. Lake Tahoe, CA 96150 Phone 800.603.1437 2 Table of Contents
More informationPRINCE 50 Parti di ricambio agg. al 30-11-09
. 缸 头 罩 部 件 CYLINDER HEAD COVER(FOR EUROPE) 50000 COVER COMP HEAD 2 5000 GASKET HEAD COVER 3 50002 Aeration Head Cover 4 50372 AERATION CAP 5 50355 TUBE BREATHER 6 50356 TIE-IN 7 50358 AERATION TUBE ASSY
More informationDESTROKED. Circuits that will be run through the Ford PCM and Ford Engine Harness
DESTROKED Thank you for your interest in Destroked. Please read through this overview to get a good idea of what is involved in your Cummins conversion project. Circuits that will be run through the Ford
More informationTABLE OF CONTENTS. Section 1 - Assembling your new pit bike.
Orion Pit Bike Sales Owners Manual (All information and content is the property of Orion Pit Bike Sales. Any attempt to copy or resell is a direct violation of our copyright. All violators will be prosecuted)
More informationWhiz Kidz 4-cylinder compact car Kids Racing Series for ages 8 15. 2015 Rules & Regulations
Whiz Kidz 4-cylinder compact car Kids Racing Series for ages 8 15 2015 Rules & Regulations Driver Eligibility Persons ages 8 years to 15 years may compete in the Whiz Kidz division. Kids who have completed
More informationVolkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing
34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed Gearshift cable/lever installing Gearshift housing repairing Gearshift lever repairing lever/relay lever, installing Gearshift mechanism
More informationREAD AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE.
491 W. Garfield Ave., Coldwater, MI 49036 Phone: 517-279-2135 Web/live chat: www.bds-suspension.com E-mail: tech-bds@sporttruckusainc.com Product: GM Leaf Spring READ AND UNDERSTAND ALL INSTRUCTIONS AND
More informationPorsche Approved Certified Pre-Owned. Limited Warranty
Porsche Approved Certified Pre-Owned Limited Warranty Porsche Approved. A guaranteed mark of quality. At Porsche, we re committed to exceptional performance. The inherent reliability and longevity of
More informationTHE CARROLL COUNTY BUCKWILD TRUCK & TRACTOR CLASSIC SATURDAY APRIL 30 TH
THE CARROLL COUNTY BUCKWILD TRUCK & TRACTOR CLASSIC SATURDAY APRIL 30 TH TRUCK DRAG RACING 2:00 PM TRUCK PULL 5:300 PM Admission $12.00/Day $20.00/Weekend Pass FOOD & BEER GARDEN AVAILABLE ON THE GROUNDS
More informationRMVR exceptions to 1972 GCR (A,B,C Production Cars and A Sedans) 3/20/2008
exceptions to 1972 GCR (A,B,C Production Cars and A Sedans) 3/20/2008 (2.1.D) Cars will comply with the 1972 SCCA PCS except for approved modifications listed in SCCA GCR and/or rules and Table 1 and Table
More informationOCEAN SPEEDWAY. American Stock TECHNICAL RULES
1 OCEAN SPEEDWAY American Stock TECHNICAL RULES Updated 02-05-2016 Ocean Speedway Inc. 8070 Soquel Drive, Suite 120 Aptos, CA 95003 [855] 410-RACE [7223] office 831-688-0708 Fax # Email:racepmg@aol.com
More informationExtended Protection Plans for New and Pre-Owned Vehicles
Extended Protection Plans for New and Pre-Owned Vehicles Protection from the Unexpected. Your vehicle is not only an investment; it s your transportation lifeline. Driver s Choice from Old Republic Insured
More informationBUYERS GUIDE. IMPORTANT: Spoken promises are difficult to enforce. Ask the dealer to put all promises in writing. Keep this form.
BUYERS GUIDE IMPORTANT: Spoken promises are difficult to enforce. Ask the dealer to put all promises in writing. Keep this form. VEHICLE MAKE MODEL YEAR VIN NUMBER DEALER STOCK NUMBER (Optional) WARRANTIES
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
More informationFJ2. 2 Ton Trolley Floor Jack Assembly & Operating Instructions
FJ2 2 Ton Trolley Floor Jack Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.
More informationPERFORMANCE PROMOTIONS TUFF TRUCK COMPETITION
PERFORMANCE PROMOTIONS TUFF TRUCK COMPETITION The Tuff Truck track will consist of different types of obstacles designed to test the limits of both vehicle and driver. Fastest time emerges victorious but
More informationMINI EXTENDED SERVICE CONTRACTS
MINI EXTENDED SERVICE CONTRACTS LESS WORRY, MORE WEEEE! CONTINUING COVERAGE FOR YOUR NEW, USED, OR CERTIFIED PRE-OWNED MINI. Whether your odometer is ticking toward the end of your original 4-year/50,000-mile
More information2003 ACCORD - Automatic Transmission Removal
2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special
More informationHOUSTON MOTORSPORTS PARK 2011 NASCAR LATE MODEL RULES
HOUSTON MOTORSPORTS PARK 2011 NASCAR LATE MODEL RULES FORWARD The rules and procedures outlined herein do not in any way ensure the safety of any official, driver, team member or spectator. These rules
More informationNortheast Sled Services LLC 2012 General Pulling Rules Farmstock and Antique Tractors
GENERAL CONTEST RULES 1) Violation of any rule will constitute a disqualification. 2) All operators must attend drivers meeting at signup area 15 minutes before pull starts. 3) Contest will be governed
More informationPREVENTION MAINTENANCE CHECKLIST FOR TRACTORS, TRUCKS, AND AUTOMOBILES
PREVENTION MAINTENANCE CHECKLIST FOR TRACTORS, TRUCKS, AND AUTOMOBILES Farm Machinery Fact Sheet FM-21 By Dr. Von H. Jarrett, Extension Agricultural Engineer Systematic sequence for inspection GASOLINE
More informationMERCEDES FIRST EDITION - 2013
FIRST EDITION - 2013 CONTENTS Accessories... 1 Hydraulic Jacks Air Intake... 2 Air Filter Charger Charging System Intake Charger Hose Intake Manifold Intake Pipe Air Filter Intercooler Charger Aircondition...
More informationENGINE Dinli 904 D1033-011
ENGINE Dinli 904 D1033-011 ENGINE Model Item Part no Description Specification Quantity 01 E140000-01 E14 ENGINE 450C.C. 1 FENDER SEAT D1033-021 FENDER SEAT Model Item Part no Description Specification
More informationLG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963
LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Thank you for purchasing LG Motorsports products for your Gen 5 Camaro. Parts Inventory:
More informationSLACK PERFORMANCE KARTS
SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction
More informationAprilia.no. RS 50 96-98 Eng.6M
01 Carburettor - oil pump 02 Drive shaft 03 Head - piston 04 Primary gear shaft 05 Gearbox driven shaft 06 Selector 07 Clutch 08 Clutch cover 09 Right crankcase 10 Left crankcase 11 Ignition unit RS 50
More informationThank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800. (installation performed on 60 Model) (Right) (Left)
740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800 A (installation performed on 60 Model) Item Description Qty A Rotor 4 B Gear Box, L 2 C
More informationEvolution of the Flathead Compiled by Fred Mills
Evolution of the Flathead Compiled by Fred Mills Here is the 221-239-255 cube U.S.A. flathead block story with pictures, to the best of my knowledge and ability to collect pictures so far. In the beginning
More information2016 Battle of the Bluegrass Rules General Regulations & Protest Procedures EVENT OPERATION AND GENERAL RULES FOR ALL CLASSES
2016 Battle of the Bluegrass Rules General Regulations & Protest Procedures EVENT OPERATION AND GENERAL RULES FOR ALL CLASSES Rules new for 2016 are highlighted. I. General Rules for All Classes The BATTLE
More informationFRAME DOOR OPENING, DOOR AND SIDE PANEL OUTER
NUBIRA/LACETTI FRAME DOOR OPENING, DOOR AND SIDE PANEL OUTER 6 1 SECTION 6 FRAME DOOR OPENING, DOOR AND SIDE PANEL OUTER CONTENTS 1. FRAME DOOR OPENING........................................... 6 2 1.1.GENERAL
More informationFOR ANY QUESTIONS, PLEASE CALL US @ 727.347.9915 M-F 8:00a.m.-8:00p.m. EST. REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915
REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915 REAR BRAKES Before getting started, remove all stock braking components. Pre-assembly of parts: Clean the bolts and the threads in the hat with acetone.
More informationInstallation manual. 1.75 front leveling kit. 2011 Dodge Durango 2011-2014 Jeep Grand Cherokee. Part # 42006. Part # 42006
Installation manual 1.75 front leveling kit 2011 Dodge Durango 2011-2014 Jeep Grand Cherokee Part # 42006 sj02282011rev.01 Part # 42006 2011-2014 Dodge Durango 2011 Jeep Grand Cherokee 1.75 front leveling
More informationSTEERING SYSTEM - POWER
STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationThird Edition. 1970-72 Corvette Technical Information Manual & Judging Guide Index
Third Edition 1970-72 Corvette Technical Information Manual & Judging Guide Index Index INTERIOR Page 3 1. Upholstery and Seat Belts Page 5 1.1. Vinyl Upholstery Page 5 1.2. Custom (Leather) Upholstery
More informationVEHICLE SERVICE CONTRACT
VEHICLE SERVICE CONTRACT The best way to help protect yourself from unexpected repair costs Protection for the Road Ahead Purchasing a vehicle is a significant investment that is worth protecting. While
More informationCustomer Owned Certified
TEREX BENFORD TA30 Customer Owned Certified OFF HIGHWAY TRUCKS Inspection Number: 751979 Serial #: A7991472 Date Created: 07/27/2011 07:46:05 AM CDT Engine Serial #: N/A Last Updated: 08/02/2011 07:10:48
More informationThis is the civilian transfer case with the cooling loop only found in the driven gear half of the front case.
INTRODUCTION The Transfer case used in the AMG Hummer is a New Venture Gear, model 242. This case has been in use for the H-1/Hummer since the early 1990 s. There have been modifications to the internal
More informationIntroduction... 2. Body Specifications... 3. Technical Data... 4. Body... 5. Interior Rear Seats... 6. Center Arm Rest... 7. Child Seat Restraint...
Table of Contents Subject Page Introduction.......................................... 2 Body Specifications.................................... 3 Technical Data........................................
More informationCONTINUED COVERAGE FOR YOUR NEW, USED, OR CERTIFIED PRE-OWNED BMW.
BMW EXTENDED SERVICE CONTRACTS FEEL THE RUSH OF ASSURANCE. CONTINUED COVERAGE FOR YOUR NEW, USED, OR CERTIFIED PRE-OWNED BMW. Whether your original 4-year/50,000-mile BMW Warranty is coming to an end,
More informationSCREAMIN' EAGLE PRO TWIN CAM 110 (1800 CC) BOLT-ON CON- VERSION KIT
-J0 REV. 0-0-0 SCREAMIN' EAGLE PRO TWIN CAM 0 (00 CC) BOLT-ON CON- VERSION KIT GENERAL Kit Number 000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section
More information125 DUKE EU 2011 SPARE PARTS MANUAL: CHASSIS ENGLISH ART.NO.: 3CF8003K4EN
SPARE PARTS MANUAL: CHASSIS ART.NO.: 3CF8003K4EN ENGLISH INDEX FRONT FORK, TRIPLE CLAMP HANDLEBAR, CONTROLS FRAME SIDE / CENTER STAND 3x 4x 5x 6x SHOCK ABSORBER SWING ARM EXHAUST SYSTEM AIR FILTER 7x
More information»Product» Safety Warning
C1200 Installation Instructions 2007-2016 Chevy/GM 1500 2/4wd 2" Strut Spacer Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationCNC Ported Big Valve Cylinder Heads. Performance Intake Manifold. Forged Pistons (Engine set with rings, pins and clips)
Performance Engine Assemblies 20001721 2.0lt Performance Crate Engine 205BHP 20001722 2.0lt Performance Crate Engine 225BHP 20001723 2.0lt Performance Crate Engine 255BHP 20001725 2.3lt Performance Crate
More information6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:
Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:
More information