Arduino. Physical Computing

Transcription

1 Physical Computing 1

2 Physical Computing System Model Behaviors 2

3 Physical Computing System Model Inputs Outputs Behaviors 3

4 Physical Computing System Model Inputs Outputs Sensors Actuators Behaviors Software/Hardware 4

5 Physical Computing System Model Inputs Outputs Sensors Button Switch Light Sound Distance Motion Temperature Magnetism Behaviors Software/Hardware Arduino Actuators LEDs LCDs Audio Motors 5

6 System Diagram Arduino 6

7 System Diagram Inputs Arduino Outputs 7

8 System Diagram Behaviors Inputs Arduino Outputs 8

9 System Diagram Behaviors Inputs Sketch Arduino Outputs 9

10 System Diagram Behaviors Inputs Sketch Arduino Outputs 10

11 System Diagram Behaviors Inputs Sketch Arduino Outputs 11

12 Arduino IDE System Diagram Behaviors Inputs Sketch Arduino Board Outputs 12

13 Board Details Arduino Uno 13

14 Board Details Pins Inputs & Outputs Pins Arduino Uno 14

15 Board Details Pins USB Inputs & Outputs Power Pins Arduino Uno 15

16 Board Details Sketch Pins USB Inputs & Outputs Power Pins Arduino Uno 16

17 Arduino IDE System Diagram Behaviors Inputs Sketch Arduino Board Outputs 17

18 Arduino IDE System Diagram 18

19 Arduino IDE IDE Details 19

20 IDE Details Code 20

21 IDE Details 21

22 IDE Details Code Console 22

23 IDE Details Upload Code Console 23

24 IDE Details Upload Code Sketch Console 24

25 IDE Details Code 25

26 IDE Details 26

27 Code Basics /* Blink Turns on an LED on for one second, then off for one second, repeatedly. Code */ This example code is in the public domain. void setup() { // initialize the digital pin as an output. // Pin 13 has an LED connected on most Arduino boards: pinmode(13, OUTPUT); } void loop() { digitalwrite(13, HIGH); delay(1000); digitalwrite(13, LOW); delay(1000); } // set the LED on // wait for one second // set the LED off // wait for one second 27

28 Code Basics /* Blink Turns on an LED on for one second, then off for one second, repeatedly. */ This example code is in the public domain. void setup() { // initialize the digital pin as an output. // Pin 13 has an LED connected on most Arduino boards: pinmode(13, OUTPUT); } setup void loop() { digitalwrite(13, HIGH); delay(1000); digitalwrite(13, LOW); delay(1000); } loop // set the LED on // wait for one second // set the LED off // wait for one second 28

29 Code Basics /* Blink Turns on an LED on for one second, then off for one second, repeatedly. */ This example code is in the public domain. ONCE void setup() { // initialize the digital pin as an output. // Pin 13 has an LED connected on most Arduino boards: pinmode(13, OUTPUT); } setup void loop() { digitalwrite(13, HIGH); delay(1000); digitalwrite(13, LOW); delay(1000); } // set the LED on // wait for one second // set the LED off // wait for one second 29

30 Code Basics /* Blink Turns on an LED on for one second, then off for one second, repeatedly. */ This example code is in the public domain. void setup() { // initialize the digital pin as an output. // Pin 13 has an LED connected on most Arduino boards: pinmode(13, OUTPUT); } FOREVER void loop() { digitalwrite(13, HIGH); delay(1000); digitalwrite(13, LOW); delay(1000); } loop // set the LED on // wait for one second // set the LED off // wait for one second 30

31 Code Basics /* Blink Turns on an LED on for one second, then off for one second, repeatedly. */ This example code is in the public domain. void setup() { // initialize the digital pin as an output. // Pin 13 has an LED connected on most Arduino boards: pinmode(13, OUTPUT); } FOREVER void loop() { digitalwrite(13, HIGH); delay(1000); digitalwrite(13, LOW); delay(1000); } loop // set the LED on // wait for one second // set the LED off // wait for one second 31

32 Code Basics /* Blink Turns on an LED on for one second, then off for one second, repeatedly. */ This example code is in the public domain. ONCE void setup() { // initialize the digital pin as an output. // Pin 13 has an LED connected on most Arduino boards: pinmode(13, OUTPUT); } setup FOREVER void loop() { digitalwrite(13, HIGH); delay(1000); digitalwrite(13, LOW); delay(1000); } loop // set the LED on // wait for one second // set the LED off // wait for one second 32

33 Hello World! Try It! /* Blink Turns on an LED on for one second, then off for one second, repeatedly. */ This example code is in the public domain. void setup() { // initialize the digital pin as an output. // Pin 13 has an LED connected on most Arduino boards: pinmode(13, OUTPUT); } void loop() { digitalwrite(13, HIGH); delay(1000); digitalwrite(13, LOW); delay(1000); } // set the LED on // wait for one second // set the LED off // wait for one second 33

34 Hello World! Arduino Uno COM6 34

35 Hello World! Blink 35

36 Hello World! Blink 36