LISTED TECHNICAL GUIDE STELLAR PLUS TM. 12 SEER SPLIT-SYSTEM HEAT PUMPS MODELS: E*FH018 Thru E*FH060 (1.5 THRU 5 NOMINAL TONS) DESCRIPTION

Transcription

1 P G Rev. A (0603) TECHNICAL GUIDE STELLAR PLUS TM 12 SEER SPLIT-SYSTEM HEAT PUMPS MODELS: E*FH018 Thru E*FH060 (1.5 THRU 5 NOMINAL TONS) This product was manufactured in a plant whose quality system is certified/registered as being in conformity with ISO Due to continuous product improvement, specifications are subject to change without notice. Visit us on the web at for the most up-to-date technical information. Additional rating information can be found at U R MA N U F A CT R E C E CE R T I F R T I UN I TA RY A R I F I I E D C A T E QU I S T A I O T O R P ME N A R S N N D A R T I AS E CT D H E AT C P U M I ON S OM P Certification applies only when the complete system is listed with ARI. O F L Y N I LISTED DESCRIPTION These high efficiency EFH Series heat pump units are the outdoor part of a versatile system designed to economically heat and cool a home or small business. The compact design of these outdoor units make them ideal for ground or roof installation. The units contain enough refrigerant charge for the outdoor unit, a matched indoor coil and 15 feet of interconnecting piping. EFH heat pumps can be custom-matched with one of YORK's two lines of evaporator blower sections, each designed to serve a specific function. Electric heaters are available for both, in a variety of sizes. For Add-On applications, the indoor coil may be applied in the supply duct of a conventional gas, oil or electric furnace. The heat pump will be the primary source of heat for the building with the furnace operating only when the heating requirement exceeds the capacity of the heat pump. WARRANTY 5-year limited parts warranty. 10-year limited compressor warranty. FEATURES QUALITY COILS - The coil is constructed of copper tube and aluminum fins. COIL PROTECTION - Coils are protected from damage by a polymer mesh applied between the coil face, and a PVC coated steel coil guard, or a polymer coil guard. DURABLE FINISH - Cabinet is made of pre-painted steel. The pretreated flat galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and glossy earth tone finish insure less fading when exposed to sunlight. LOWER INSTALLED COST - Installation time and costs are reduced by the fully exposed refrigerant connections and the single panel covering of the electrical controls. The small base dimension means smaller mounting pads or less materials required for mounting, lowering installation costs. COMPRESSOR ton models are equipped with scroll compressors which are internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protect the compressor if undesirable operating conditions occur. The compressor is protected by a 10 year limited warranty. COMPLETE SYSTEM CONTROL - These heat pump units utilize the unique YorkGuard V microprocessor control system to provide optimal comfort control and assure reliable operation. The YorkGuard V control system continuously monitors the space environment to maintain optimum efficiency. It initiates defrost only when necessary to further reduce heating costs and improve reliability. Supplemental heat can only operate below the balance point and then only upon need. In the event of improper operating conditions (high temperature and high pressure), the YorkGuard V will shut the system down to extend the life of the heat pump. Rapid cycling is prevented by use of an integral anti-recycle timer. Loss of charge protection is provided by a discharge temperature sensor and internal compressor overloads. Finally the YorkGuard V control provides system diagnostics to aid the service technician, minimizing repair time and cost. The YorkGuard V control even stores important information for use during servicing and has a 5 year warranty. LOW OPERATING SOUND LEVEL - The discharge air from the top mounted fan is blown up away from the structure and any landscaping carrying the normal operating noise up away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. U.L. and C.U.L. listed - approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240. FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

2 PHYSICAL AND ELECTRICAL DATA MODEL E4FH018 E4FH024 E4FH030 E4FH036 E4FH045 E5FH048 E4FH060 Unit Supply Voltage 208/ Normal Voltage Range to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Compressor Type 3 Recip Scroll C Scroll C Scroll C Scroll C Scroll C Scroll C Compressor Amps Rated Load Crankcase Heater Yes No No No No No No Fan Motor Amps Rated Load Fan Diameter Inches Fan Motor Rated HP 1/12 1/12 1/8 1/4 1/4 1/4 1/3 Nominal RPM Nominal CFM Face Area Sq. Ft Coil Rows Deep Fin / Inches Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line OD 5/8 5/8 3/4 7/8 7/8 7/8 1-1/8 Unit Charge (Lbs. - Oz.) Charge Per Foot, Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2. Dual element fuses or HACR circuit breaker. 3. All scrolls listed with a superscript B are Bristol scrolls. All scrolls listed with a superscript C are Copeland scrolls. 4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value. 48" OVERHEAD CLEARANCE C All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon request. A B AIR IN 4 SIDES UNIT MODEL EFH REFRIGERANT DIMENSIONS CONNECTION LINE SIZE A B C LIQUID VAPOR / / / / / / / / / / / /8 1 VAPOR CONNECTION 5-1/2 2-3/8 1. Valve on 060 is 7/8 with a reducer supplied for the 1-1/8 vapor line. LIQUID CONNECTION 3-1/8 2 Unitary Products Group

3 ADDITIONAL R-22 CHARGE / ORIFICE SIZE FOR VARIOUS MATCHED SYSTEMS OUTDOOR UNIT E4FH018 E4FH024 E4FH030 E4FH036 E4FH042 E5FH048 E4FH060 Orifice in OD Distributor FACTORY CHARGE, LBS. - OZ ID Orifice included w/instruction Package INDOOR COIL COIL ORIFICE 1 REQUIRED SYSTEM ORIFICE + ADDITIONAL CHARGE, OZ. G1FA/G1UA024S14, G1FA/G1UA030S G1FA/G1UA036S G1FA/G1UA036S G1FA/G1UA048S G1FA/G1UA048S G1FA/G1UA060S21, G2FD024S(H)14, G2FD030S(H) GFD035S(H) G2FD036S(H) G2FD042S(H) G2FD046S(H) G2FD048S(H)21, G2FD060S(H) G2FD061SH G1HD G1HD G1HD G1HD F2RP/FP018 (53) (55) F2RP/FP F2RP/FP F2RP/FP F2RP/FP F2FP F2FP F2FV FOOTNOTES: 1. Verify the TXV kit and the additional charge required for the specific evaporator coil in the system using the table above. PROCEDURES: 1. Unit factory charge listed on the unit nameplate includes refigerant for the condenser, the smallest evaporator and for 15 feet of interconnecting line tubing. 2. Verify the orifice size and the additional charge required for the specific evaporator coil in the system using the table above: 3. Add additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above. 4. Permanently mark the unit nameplate with the total system charge. Total System Charge=Base Charge (as shipped) +adder for evaporator +adder for line set. 5. If the orifice in the evaporator was changed verify the evaporator nameplate has been marked with the correct orifice size. Unitary Products Group 3

4 COOLING CAPACITY - With Air Handler Coils UNIT MODEL E4FH018 - = Not applicable MODEL AIR HANDLER ELECTRIC HEAT KW 2 COIL MODEL 1 RATED NET MBH W CFM TOTAL SENS. 1 Phase 12 SEER HP / N1AH / G2FD COOLING SEER W/O TXV 1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number. 2. Single phase units require single phase 2HK heaters. 3. TXV = Use 1TV700 Series Kit. 4. To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC. models. All ratings remain the same. 5. FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D (Blower on Delay) standard. SEER + TXV 3 N1AHB08 2,5,7.5,10 17 G2FD024(S,H) N1AHB08 2,5,7.5,10 17 G2FD030(S,H) N1AHB08 2,5,7.5,10 17 G2FD024(S,H) E4FH024 N1AHB08 2,5,7.5,10 17 G2FD030(S,H) N1AHB08 2,5,7.5,10 14 G2FD035(S,H) E4FH030 N1AHB12 5,7.5,10,15,18 17 G2FD036(S,H) E4FH036 N1AHB12 5,7.5,10,15,18 17 G2FD036(S,H) E4FH042 E5FH048 N1AHC16 5,7.5,10,15,20 21 G2FD042(S,H) N1AHC16 5,7.5,10,15,20 21 G2FD048(S,H) N1AHC ,10,15,20 21 G2FD048(S,H) N1AHD ,10,15,20,25,30 24 G2FD060(S,H) E4FH060 N1AHD20 7.5,10,15,20,25,30 24 G2FD060(S,H) N1AHD20 7.5,10,15,20,25,30 24 G2FD061H Phase 12 SEER HP / N1VS / G2FD E4FH018 N1VSB12 5,7.5,10,15,18 17 G2FD024(S,H) E4FH024 N1VSB12 5,7.5,10,15,18 17 G2FD024(S,H) N1VSB12 5,7.5,10,15,18 17 G2FD030(S,H) E4FH030 N1VSB12 5,7.5,10,15,18 17 G2FD036(S,H) E4FH036 N1VSB12 5,7.5,10,15,18 17 G2FD036(S,H) E4FH042 E5FH048 E4FH060 E4FH018 E4FH024 E4FH030 E4FH036 E4FH042 E5FH048 E4FH060 N1VSC16 5,7.5,10,15,20 21 G2FD042(S,H) N1VSC16 5,7.5,10,15,20 21 G2FD048(S,H) N1VSC ,10,15,20 21 G2FD048(S,H) N1VSD ,10,15,20,25,30 24 G2FD060(S,H) N1VSD20 7.5,10,15,20,25,30 24 G2FD060(S,H) N1VSD20 7.5,10,15,20,25,30 24 G2FD061H Phase 12 SEER HP / F2RP / FP / FV 4,5 F2RP/F2FP018 5,8, F2RP/F2FP024 5,8, F2RP/F2FP024 5,8, F2RP/F2FP030 5,8,10, F2RP/F2FP030 5,8,10, F2RP/F2FP036 5,8,10, F2RP036 5,8,10, F2RP042 5,8,10, F2RP042 5,8,10, F2FP048 10,15,20, F2FP048 10,15,20, F2V060 10,15,20, F2FP060 10,15,20, F2FP060 10,15,20, F2FV060H24 10,15,20, Rated in accordance with DOE test procedures (Federal Register and ) and ARI Standards 210/240. Cooling MBH based on 80 F entering air temperature, 50% RH, and rated air flow. EER (Energy Efficiency Ratio) is the total cooling output in BTU s at a 95 F outdoor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period. EER 4 Unitary Products Group

5 COOLING CAPACITY - With Upflow, Downflow and Horizontal Furnace and Coils UNIT MODEL E4FH018S06 E4FH024S06 E4FH030S06 E4FH036S06 E4FH042S06 E5FH048S06 E4FH060S06 FURNACE** NOMINAL W AIRFLOW COIL MODEL RATED CFM TOTAL NET MBH SENS. COOLING SEER W/O TXV SEER + TXV 1 14,17 G1FA024S14, G1FA030S ,17 G1UA024S14, G1UA030S ,17 G2FD024S14, G2FD030(S,H) G2FD035(S,H) G1FA030S G1UA030S ,21 G1FA036S17, G1UA036S17, G1HD G2FD024(S,H)14, G2FD030(S,H) G2FD035(S,H) G1FA036S ,21 G1FA036S17, G1HD G1UA036S ,21 G1UA036S17, G2FD030(S,H) G2FD030(S,H) G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G1FA048S G1FA048S G1UA048S G1UA048S G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) G2FD046(S,H) G1FA048S G1FA048S G1UA048S G1UA048S G2FD042(S,H) G2FD046(S,H) ,24 G2FD048(S,H)21, G1FA048S ,24 G1FA060S21, G1UA048S ,24 G1UA060S21, ,24 G2FD048(S,H)21, G2FD060(S,H) ,24 G1FA060S21, ,24 G1UA060S21, G2FD060(S,H) G2FD061H EER 1. TXV = Use 1TV700 Series Kit. * Requires a 2FD Blower Time Delay unless a standard furnace is equipped with one. ** Refer to Quick Selection Chart for specific furnace match-up. Unitary Products Group 5

6 HEATING PERFORMANCE - Air Handler and Multi-position Coils UNIT MODEL E4FH018 E4FH024 E4FH030 E4FH036 E4FH042 E5FH048 COIL 1 MODEL ARI HEATING 2 OUTDOOR TEMP 3 47 F 17 F HSPF -3 F 7 F 17 F 27 F 37 F 47 F 57 F MBH COP MBH COP STD. V. S. MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW F2RP/F2FP F2RP/F2FP G2FD024(S,H)14, G2FD030(S,H) G2FD035(S,H) F2RP/F2FP F2RP/F2FP G2FD024(S,H)14, G2FD030(S,H) G2FD035(S,H) F2RP/F2FP F2RP/F2FP G2FD030(S,H) G2FD035(S,H) G2FD036(S,H)17, F2RP/F2FP F2RP/F2FP G2FD042(S,H) G2FD046(S,H) G2FD036(S,H)17, F2RP/F2FP F2FP G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21, F2FP F2FP G2FD048(S,H)21, G2FD060(S,H) F2FP E4FH060 F2FV G2FD060(S,H) G2FD061H For Notes See Page 7. 6 Unitary Products Group

7 HEATING PERFORMANCE - Furnace Coils UNIT MODEL E4FH018 E4FH024 E4FH030 E4FH036 E4FH042 E5FH048 E4FH060 COIL 1 MODEL ARI HEATING 2 OUTDOOR TEMP 3 47 F 17 F HSPF -3 F 7 F 17 F 27 F 37 F 47 F 57 F MBH COP MBH COP STD. V. S. MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW E*FH WITH (VARIABLE SPEED & STANDARD) FURNACE COILS G1HD G1FA024S G1UA024S G1FA030S G1UA030S G1HD G1FA030S G1UA030S G1FA036S17, G1UA036S17, G1HD G1FA036S G1UA036S G1FA036S17, G1UA036S17, G1FA048S G1UA048S G1FA048S G1UA048S G1FA048S G1UA048S G1FA048S G1UA048S G1FA048S G1UA048S G1FA060S21, G1UA060S21, G1FA060S21, G1UA060S21, Rated CFM same as for cooling. 2. Heating MBH based on ARI standards of 70 DB entering indoor air, 72% RH outdoor air with 25 feet of interconnecting piping and no supplemental electric heat operation. 3. Integrated heating capacities include the effect of defrost cycles in the temperature range where they occur. COP equals MBH output divided by (total KW input x 3.412). HSPF (Heating Seasonal Performance Factor) is the total heating output during a normal annual usage period for heating divided by the total electric power input during the same period. = Not Applicable. Unitary Products Group 7

8 ACCESSORIES Refer to Price Manual for specific model numbers. Start Assist Kit (2SA067*) Blower Time Delay - Available to increase efficiency when installed. Installs on indoor section and maintains blower for approximately one minute after cooling thermostat has been satisfied. Hard Start Kits - Provides required starting torque for use with Thermal Expansion Valve Kit. Low Temperature Cutout (2LT ) - Prevents heat pump operation below -10 F ambient temperature. Compressor Blanket - Designed to further reduce the normal operating sound. Add-on Control (2AC ) - Provides interface for use of gas and oil furnaces with the heat pump system. Thermal Expansion Valve Kit - 1TV0700 Series TXV kit used to improve system performance. Outdoor Thermostat (2TD ) - Provides additional staging of supplemental electric heat. Room Thermostats - A wide selection of matching thermostats is available to provide features required for any installation. 2H/1C, manual change-over electronic non-programmable thermostat. 3H/2C, non-programmable digital thermostat. 3H/2C, auto/manual changeover, electronic programmable, 7-day, thermostat. * For the most current accessory information, refer to the price book or consult factroy. SOUND BLANKET EFH MODEL SOUND RATING DECIBELS *Rated in accordance with ARI Standard Unitary Products Group

9 TYPICAL INSTALLATION TO INDOOR BLOWER THERMOSTAT TO POWER SUPPLY NEC CLASS 1 WIRING WEATHERPROOF DISCONNECT SWITCH 48 OVERHEAD CLEARANCE 12 REAR AND SIDES NEC CLASS 2 WIRING TO COIL 24 SERVICE ACCESS CLEARANCE NOTE: All outdoor wiring must be weatherproof Seal opening(s) with permagum or equivalent TYPICAL FIELD WIRING - (AIR HANDLER / ELECTRICAL HEAT) ALL WIRING TO BE ACCORDANCE WITH NATIONAL CODE AND/OR LOCAL CODES. THERMOSTAT O XorL R BorC Y W G 2 TERMINAL NOT USED ON ALL THERMOSTATS. 3 FOR TYPICAL FIELD WIRING WITH N*VS VARIABLE SPEED AIR HANDLER, SEE N*VS INSTRUCTIONS. 4 CONNECT POWER WIRING TO TERMINAL BLOCK ON UNITS WITHOUT ELECTRIC HEAT OR UNITS WITHOUT ACIRCUIT BREAKER. 3 INDOOR UNIT ELECTRIC HEATER ACCESSORY O R C Y G W2 W1 CIRCUIT BREAKER 4 GND. LUG OUTDOOR UNIT S1* S2* O XorL R BorC Y W W2/60 W1/66 * BONNET SENSOR CONNECTIONS FOR ADD-ON SYSTEM. CONTACTOR T2 T1 GND. SCREW L2 M L1 POWER WIRING 24V CONTROL WIRING (NEC CLASS 2) POWER WIRING 208/ POWER WIRING 208/ Unitary Products Group 9

10 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER AIR TEMPERATURE E4FH018S06 F2RP/F2FP024 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. N1AHB08 G2FD024(S,H) N1AHB08 G2FD030(S,H) N1VSB12 G2FD024(S,H) F2RP/F2FP G1UA024S G1UA024S G2FD024(S,H) G2FD024(S,H) G1UA030S G2FD030(S,H) G2FD030(S,H) G1FA024S G1FA024S G1FA030S Unitary Products Group

11 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER AIR TEMPERATURE E4FH024S06 F2RP/F2FP030 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. N1AHB08 G2FD024(S,H) N1AHB08 G2FD030(S,H) N1AHB08 G2FD035(S,H) N1VSB12 G2FD024(S,H) F2RP/F2FP G2FD024(S,H) G2FD024(S,H) G1HD G1UA030S G1UA036S G1UA036S G2FD030(S,H) G2FD035(S,H) G1FA030S G1FA036S G1FA036S Unitary Products Group 11

12 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER AIR TEMPERATURE E4FH030S06 G2FD030(S,H)17 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. N1AHB12 G2FD036(S,H) N1VSB12 G2FD030(S,H) N1VSB12 G2FD036(S,H) F2RP/F2FP F2RP/F2FP G1UA036S17, G1HD G1UA036S G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G1FA036S17, G1FA036S Unitary Products Group

13 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER AIR TEMPERATURE E4FH036S06 F2RP/F2FP036 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. N1AHB12 G2FD036(S,H) N1VSB12 G2FD036(S,H) F2RP G1UA048S G1UA048S G2FD42(S,H) G2FD046(S,H) G2FD036(S,H) G2FD036(S,H) G1FA048S G1FA048S Unitary Products Group 13

14 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER AIR TEMPERATURE E4FH042S06 F2RP/F2FP042 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. N1AHC16 G2FD042(S,H) N1AHC16 G2FD048(S,H) N1VSC16 G2FD042(S,H) N1VSC16 G2FD048(S,H) F2FP G2FD042(S,H) G1UA048S G1UA048S G1UA046S G2FD048(S,H) G2FD048(S,H) G1FA048S G1FA048S G1FA046S Unitary Products Group

15 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER AIR TEMPERATURE E5FH048S06 F2FP048 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. N1AHC16 G2FD048(S,H) N1AHD20 G2FD060(S,H) N1VSC16 G2FD048(S,H) N1VSD20 G2FD060(S,H) F2V F2FP G2FD048(S,H) G2FD048(S,H) G1UA048S G1UA060S G1UA060S G2FD060(S,H) G1FA048S G1FA060S G1FA060S Unitary Products Group 15

16 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSER AIR TEMPERATURE E4FH060S06 G2FD060(S,H)24 ID CFM ID DB ( F) ID WB ( F) T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W T.C S.C K.W NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. N1AHD20 G2FD060(S,H) N1AHD20 G2FD061H N1VSD20 G2FD060(S,H) N1VSD20 G2FD061H F2FP F2FV060H G1UA060S G1UA060S G2FD061H G1FA060S G1FA060S Unitary Products Group

17 HEATING PERFORMANCE DATA CONDENSING UNIT MODEL NO. EVAPORATOR COIL MODEL NO. OUTDOOR UNIT INDOOR COIL E4FH018S06 F2RP/F2FP024 ID CFM MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM. F2RP/F2FP G2FD024(S,H)14, G2FD030(S,H) G2FD035(S,H) Unitary Products Group 17

18 HEATING PERFORMANCE DATA CONDENSING UNIT MODEL NO. EVAPORATOR COIL MODEL NO. OUTDOOR UNIT INDOOR COIL E4FH024S06 F2RP/F2FP030 ID CFM MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM. F2RP/F2FP G2FD035(S,H) G2FD030(S,H) G2FD024(S,H)14, Unitary Products Group

19 HEATING PERFORMANCE DATA CONDENSING UNIT MODEL NO EVAPORATOR COIL MODEL NO OUTDOOR UNIT INDOOR COIL E4FH30S06 G2FD030(S,H)17 ID CFM MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM. F2RP/F2FP F2RP/F2FP G2FD035(S,H) G1HD G2FD036(S,H) G2FD036(S,H) G1UA036S G1FA036S G1UA036S17, G1FA036S17, Unitary Products Group 19

20 HEATING PERFORMANCE DATA CONDENSING UNIT MODEL NO. EVAPORATOR COIL MODEL NO. OUTDOOR UNIT INDOOR COIL E4FH036S06 F2RP/F2FP036 ID CFM MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM. F2RP/F2FP G2FD036(S,H)17, G2FD042(S,H) G2FD046(S,H) Unitary Products Group

21 HEATING PERFORMANCE DATA CONDENSING UNIT MODEL NO EVAPORATOR COIL MODEL NO OUTDOOR UNIT INDOOR COIL E4FH042S06 F2RP/F2FP042 ID CFM MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM. F2FP G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21, Unitary Products Group 21

22 HEATING PERFORMANCE DATA CONDENSING UNIT MODEL NO EVAPORATOR COIL MODEL NO OUTDOOR UNIT INDOOR COIL E5FH048S06 F2FP048 ID CFM MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM. F2FP G2FD048(S,H)21, G2FD060(S,H) Unitary Products Group

23 HEATING PERFORMANCE DATA CONDENSING UNIT MODEL NO EVAPORATOR COIL MODEL NO OUTDOOR UNIT INDOOR COIL E4FH060S06 G2FD060(S,H)24 ID CFM MBTUH K.W. C.O.P. MBTUH K.W. C.O.P. MBTUH K.W. C.O.P NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM. F2FP F2FV G2FD061H Unitary Products Group 23