Aluminium Systems Specification Guide

Transcription

1 Uniclass L411 +L413:P7114 CI/SfB 9/11 EPIC D11 +D13:X725 (31.4)+(31.5) Xn6 Aluminium Systems Specification Guide A brand new design concept that delivers unrivalled thermal performance ARCHITECTURAL A BRAND OF THE VEKA UK GROUP

2 A radical reinterpretation of the aluminium window System10 Aluminium from Bowater Architectural, part of Bowater Building Products Limited is a radical new design concept. It looks like aluminium but at its heart is a specially designed substrate that improves thermal and environmental performance beyond that normally associated with aluminium. This means System10 Aluminium can be specified where ordinary aluminium windows cannot, including buildings required to meet the most stringent thermal and ecological standards. u System10 Aluminium: Provides a U-Value of 1.4W/m 2 K when fitted with standard double glazed units u Can be manufactured to provide a U-Value as low as 0.7W/m 2 K u Meets the requirements of levels 3, 4, 5, and 6 of the Code for Sustainable Homes.

3 A revolution with heritage System10 Aluminium is a development of System10 PVC-U the market leading commercial window and door system from WHS Halo, a division of Bowater Building Products Limited. System10 has been used to great success for over 25 years and is held in high regard by Local Authorities, specifiers and homeowners alike. Code for sustainable homes meet Code level 6 now! The Government has set a target that by 2016 (2013 for the social sector) all new homes will be zero carbon rated (Code level 6). To achieve that level all windows have to have a U-value of 0.7W/m 2 K or less. Aesthetics and performance System10 Aluminium: u Can be used to create large glazed areas and large opening sashes in this respect it equals, or betters pure aluminium framing systems u Can be powder coated in any RAL colour and the inside can be a different colour from the outside or laminated to reproduce timber interior finishes u Is more cost effective than thermally broken aluminium systems u Can be manufactured to achieve a U-value as low as 0. 7W/m 2 K u Standard U-value is 1.4W/m 2 K, and any value between 1.4W/m 2 K and 0.7W/m 2 K can be achieved simply by varying standard components u Has concealed gaskets for clean sightlines u Has concealed drainage (wherever possible), no unsightly slots u Accepts standard hardware that can be easily maintained Meeting the standard System10 Aluminium has been fully tested and shown they meet the following standards: u BS 7950 u PAS23 and PAS24 u BS 8213 Exceptional performance the result of exceptional design System10 Aluminium s ability to deliver such exceptional performance is the result from a combination of unique design concepts. They include: u A specially designed, multi-chamber substrate that all but eliminates cold bridging. u Foam filled inserts that further improve the insulating properties of the substrate u Specially designed seals that prevent heat loss around glazed units and between the sash and the frame

4 The most cost effective The table below compares the costs and performance of a number of window systems. It shows that System10 Aluminium costs considerably less than other systems, and yet provides better all-round performance and design opportunities. COST EFFICIENCY FRAME COMPARISON Frame Type System10 Aluminium Softwood Aluminium/PVC-U Aluminium/softwood Av. frame depth mm 136mm 95mm Glazing 36mm Triple Krypton 44mm Triple Argon 44mm Triple Argon 36mm Triple Krypton Av. frame U-value Code for Sustainable Homes (level achieved) Zero Carbon Zero Carbon Zero Carbon Zero Carbon Performance Price index* FRAME SUMMARY Frame Type System10 PVC-U System10 Aluminium Timber Aluminium Av. frame depth 70mm 70mm 87mm 54mm Av. frame U-value Code for Sustainable 3 & 4 3 & 4 3 & 4 NOT COMPLIANT Homes (level achieved) Performance Price index* *The performance/price index is calculated by multiplying the price of a standard window by the U-value achieved by the system. The best result, i.e. the lowest answer, is then set to 100 and the other indices calculated accordingly. Average of 8 frames (min. 68mm - max. 115mm) Average of 20 frames (min. 47mm - max. 75mm)

5 Casement Windows The System10 Aluminium open out casement is a high performance window which, because of its ingenious design enables aluminium framed windows to be specified for buildings designed to meet the Code for Sustainable Homes. It features slim, bevelled sightlines and a 70mm front to back dimension. Opening sashes may be top hung or side hung. Maximum Sizes Standard - internal beaded casement sash double glazed Side hung 700mm (w) x 1300mm (h) 12 friction stay with 21kg weight carrying capacity Top hung 1250mm (w) x 1250mm (h) 24 friction stay with 26kg weight carrying capacity Smart - internal beaded casement sash double glazed Side hung 1100mm (w) x 2100mm (h) butt hinges or dedicated stay arms with 80kg weight carrying capacity Top hung 1500mm (w) x 1700mm (h) butt hinges or dedicated stay arms with 80kg weight carrying capacity Smart - internal beaded casement sash triple glazed Side hung 900mm (w) x 1800mm (h) butt hinges or dedicated stay arms with 80kg weight carrying capacity Top hung 1300mm (w) x 1500mm (h) butt hinges or dedicated stay arms with 80kg weight carrying capacity GLAZING System10 Aluminium is internally glazed and can accommodate glazing units from 24mm to 36mm U-VALUES System10 Aluminium Casement window meets the current requirements of Building Regulations when fitted with an appropriately specified 28mm double glazed unit. U-Values of 1.4W/m 2 K can be achieved if the window is fitted with a standard 28mm double glazed unit. This level of thermal insulation complies with Code level 3 & 4 of the Code for Sustainable Homes. For further information contact the Technical Department at WHS-Halo or visit our website. The System10 Aluminium casement window also achieves A ratings when assessed against the criteria of the Windows Energy Rating Scheme (WER). STANDARDS System10 Aluminium can be used to manufacture windows that conform to BS6375 Part 1 & 2 and BS7950, the standard for enhanced security. COLOURS System10 Aluminium can be powder coated in any RAL colour different colours can be specified for inside and outside.

6 Top Swing/Fully Reversible Windows The System10 Aluminium top swing window is ideal for use in areas where access for cleaning is limited such as high rise buildings. When fully opened the window protrudes entirely to the outside leaving internal decorations and window coverings undisturbed. It features bevelled sightlines and a 70mm front to back dimension. Maximum Sizes Double glazed Triple glazed 1500mm (w) x 1600mm (h) 1200mm (w) x 1300mm (h) GLAZING System10 Aluminium is internally glazed and can accommodate glazing units from 24mm to 48mm U-VALUES System10 Aluminium Top swing windows meets the current requirements of Building Regulations when fitted with an appropriately specified 28mm double glazed unit. U-Values of 1.4W/m 2 K can be achieved if the window is fitted with a standard 28mm double glazed unit. This level of thermal insulation complies with Code level 3 & 4 of the Code for Sustainable Homes. For further information contact the Technical Department at Bowater Architectural or visit our website. This window also achieves A ratings when assessed against the criteria of the Windows Energy Rating Scheme (WER). STANDARDS System10 Aluminium can be used to manufacture windows that conform to BS6375 Part 1 & 2 and BS7950, the standard for enhanced security. The System10 Aluminium top swing window can be safely cleaned from the inside in accordance with BS8213. COLOURS System10 Aluminium can be powder coated in any RAL colour - different colours can be specified for inside and outside.

7 Tilt & Turn Windows The System10 Aluminium Tilt and Turn window is a high performance aluminium window which, because of its ingenious design, offers unbeatable thermal performance at a very competitive cost. The hinge and locking system allows the window to be used as a side hung open in sash, or as a tilt in sash hinged at the bottom. It features bevelled sightlines and a 70mm front to back dimension. Maximum Sizes Double glazed Triple glazed 1500mm (w) x 1500mm (h) OR 1100mm (w) x 2100mm (h) 1500mm (w) x 1500mm (h) OR 900mm (w) x 2100mm (h) GLAZING System10 Aluminium is internally glazed and can accommodate glazing units from 24mm to 36mm U-VALUES System10 Aluminium Tilt & Turn windows meets the current requirements of Building Regulations when fitted with an appropriately specified 28mm double glazed unit. U-Values of 1.4W/m 2 K can be achieved if the window is fitted with a standard 28mm double glazed unit. This level of thermal insulation complies with Code level 3 & 4 of the Code for Sustainable Homes. For further information contact the Technical Department at Bowater Architectural or visit our website. This window also achieves A ratings when assessed against the criteria of the Windows Energy Rating Scheme (WER). STANDARDS System10 Aluminium can be used to manufacture windows that conform to BS6375 Part 1 & 2 and BS7950, the standard for enhanced security. The System10 Aluminium Tilt & Turn windows can be safely cleaned from the inside in accordance with BS8213. COLOURS System10 Aluminium can be powder coated in any RAL colour - different colours can be specified for inside and outside.

8 In-line Pivot Windows The System10 Aluminium in-line pivot window has been designed to replicate large timber pivots often found in high rise applications. The large opening sash sizes that are possible with this system allows like for like replacements in most cases and opens up a wide range of design opportunities. Multi point perimeter gearing ensures high security, and maximum compression on weather seals, providing excellent weather performance. The windows also feature restrictors for safety. Pivot hinge allows the window to be cleaned safely from the inside. Maximum Sizes (based on shootbolt locking) Double glazed Triple glazed 1500mm (w) x 1600mm (h) 1200mm (w) x 1300mm (h) GLAZING System10 Aluminium is internally glazed and can accommodate glazing units from 24mm to 36mm U-VALUES System10 Aluminium In-line pivot windows meets the current requirements of Building Regulations when fitted with an appropriately specified 28mm double glazed unit. U-Values of 1.4W/m 2 K can be achieved if the window is fitted with a standard 28mm double glazed unit. This level of thermal insulation complies with Code level 3 & 4 of the Code for Sustainable Homes. For further information contact the Technical Department at Bowater Architectural or visit our website. This window also achieves A ratings when assessed against the criteria of the Windows Energy Rating Scheme (WER). STANDARDS System10 Aluminium can be used to manufacture windows that conform to BS6375 Part 1 & 2 and BS7950, the standard for enhanced security. The open in facility allows the outside pane to be cleaned in accordance with BS8213. COLOURS System10 Aluminium can be powder coated in any RAL colour - different colours can be specified for inside and outside.

9 Residential Doors The System10 Aluminium Residential Door is a high performance door which, because of its ingenious design, offers unbeatable thermal performance at a very competitive cost. It features bevelled sightlines and a 70mm front to back dimension. Maximum Sizes Double glazed Triple glazed 1150mm (w) x 2200mm (h) 1150mm (w) x 2200mm (h) GLAZING System10 Aluminium is internally glazed and can accommodate glazing units and door panels from 24mm to 36mm U-VALUES System10 Aluminium residential door meets the current requirements of Building Regulations when fitted with appropriately specified 28mm double glazed units and/or door panels. STANDARDS System10 Aluminium can be used to manufacture doors that conform to PAS23 and PAS 24, the standards that cover weather tightness and enhanced security. COLOURS System10 Aluminium can be powder coated in any RAL colour - different colours can be specified for inside and outside.

10 Services to the construction industry Manufacture & distribution Here at Bowater Architectural we want to make choosing, specifying, purchasing, installing and maintaining our products as easy as possible. As well as our highly trained and experienced Technical Department, based at our Head Office, we have a team of Development Managers who provide on the spot help and advice. The services we offer include: The profiles used to manufacture System10 Aluminium windows and doors are extruded under a quality assurance management system accredited to ISO9001:2000. The profiles meet or exceed the requirements of BS EN 12608:2003. u Full technical back up including specifications (Bowater Architectural s products are included on NBS+ specifications), drawings, site surveys and calculations u Window and door manufacture through our network of fabricator partners u An installation service u Over all project management, including client liaison u Full maintenance plans Since 1979 we have been designing and supplying window profile to fabricators and installers in the UK and Ireland. All of our activity takes place at Minworth in Sutton Coldfield. Our extrusion facility has its own polymer blending plant, an in-house tool room and a foiling facility. We also have an in-house quality testing centre and a 100,000 square ft modern distribution centre.

11 Other products Veka and all its related companies manufacture and supply a wide range of energy efficient fenestration solutions. They are suitable for use in all sectors, for new build and refurbishment. WINDOW STYLES AVAILABLE PVC-U Casement PVC-U Tilt and Turn PVC-U Top swing or fully reversible PVC-U In-line Pivot PVC-U Vertical sliding sash DOOR STYLES AVAILABLE PVC-U French patio PVC-U Sliding patio PVC-U Bi fold Composite single and double rebate Utility/fire rated doors Flood Defence Doors The Environment Veka and all its related companies are totally committed to ensuring our activities have zero or minimal impact on the environment. Our products are designed to save energy and reduce carbon emissions. Our manufacturing facilities are constantly audited to ensure our resource use is minimised and our waste disposal and recycling facilities are as efficient as possible. In 2000 we were one of the first PVC-U window profile extruders in the UK to be awarded the International Standard for Environmental Management (ISO 14001). In 2009 and 2010 we were awarded a prestigious Green Apple Award in recognition of our innovative energy saving window systems.

12 ARCHITECTURAL Further information Veka has an extensive and easily searchable website, putting the information you need at your finger tips. Go to to find more detailed information about our products and service. There is also an enquiry service, so if you cannot find exactly what you need you can us for a timely response. ARCHITECTURAL A BRAND OF THE VEKA UK GROUP Bowater Architectural Water Orton Lane Minworth Sutton Coldfield West Midlands B76 9BW Tel: Fax: info@bowaterarchitectural.com This Data has been prepared by Bowater Architectural, a division of Veka, with reasonable care for general guidance purposes only. Reliance on the information contained in this document shall be the entire responsibility of the person/persons so relying and in no event shall Veka be liable for any direct loss or damage attributable to reliance on this Technical Data Sheet. Under no circumstances shall Veka be liable for any indirect or consequential loss or damage including, but not limited to, loss of profit and loss of contracts. As part of our policy of continuous improvement we reserve the right to alter specifications without prior notice. Veka 2010 EE00072