AA 5450 Ultra Thermal Window
|
|
|
- Curtis Dean
- 7 years ago
- Views:
Transcription
1 JULY, 2014 AA 5450 Ultra Thermal Window INDEX 1 FIXED WINDOW SINGLE HUNG WINDOW DOUBLE HUNG WINDOW HORIZONTAL SLIDING WINDOW WINDLOAD CHARTS... 4 RECEPTORS... 5 ANCHORS... 6 THERMAL CHARTS LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI) units are found in these details: m meter cm centimeter mm millimeter s second Pa pascal MPa megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement.
2 2 AA 5450 Ultra Thermal Window JULY, 2014 BLANK PAGE
3 JULY, 2014 AA 5450 Ultra Thermal Window FIXED WINDOW Standard Features High Performance Architectural Grade Window Tested to U.S. and Canadian Standards Polyamide Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Interior and Exterior Dual Finish Options Two Year Manufacturer's Warranty Thermal Break Exterior Interior Fixed Window For specific product applications, Consult your Kawneer representative.
4 4 AA 5450 Ultra Thermal Window JULY, 2014 FIXED WINDOW CLASS and GRADE TESTING METHOD CLASS AW-PG70-FW AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) FRAME DEPTH 4-5/8" Overall Frame Depth TYPICAL WALL THICKNESS 0.070" Nominal TYPICAL MAXIMUM WINDOW SIZE 60" X 99" TYPICAL MINIMUM WINDOW SIZE 15" X 15" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" and 1-1/2" STANDARD HARDWARE Not Applicable OPTIONAL HARDWARE Not Applicable OTHER OPTIONS Between the Glass Muntins Historic Beveled Exterior Glazed-in Muntins (1-1/2" max. overall thickness) Exterior and Interior Tape Applied Muntins Perimeters and Sills Exterior Pannings and Interior Trims True Intermediate Muntin Structural Mullions H-Mullion for vertical stacking Strap Anchors Male/Female horizontally stacked
5 JULY, 2014 SCALE : " = 1'-0" AA 5450 Ultra Thermal Window FIXED WINDOW 5 AA 5450 FIXED WINDOW (1" Double Glazed) 4-5/8" HEAD 2 HORIZONTAL 2" 2-5/8" -5/8" 2" TYPICAL ELEVATION Log onto www. for other configurations 4-5/8" 4-5/8" A (Panning Fin) VARIES 2" 4-5/8" 2" 2-5/8" 2" JAMB VERTICAL JAMB
6 6 AA 5450 Ultra Thermal Window JULY, 2014 FIXED WINDOW SCALE : " = 1'-0" AA 5450 FIXED WINDOW (1-1/2" Triple Glazed) 4-5/8" HEAD 2 HORIZONTAL 2" 2-5/8" -5/8" 2" TYPICAL ELEVATION Log onto www. for other configurations 4-5/8" 4-5/8" A (Panning Fin) VARIES 2" 4-5/8" 2" 2-5/8" 2" JAMB VERTICAL JAMB
7 JULY, 2014 AA 5450 Ultra Thermal Window SINGLE HUNG WINDOW 7 Standard Features High Performance Architectural Grade Window Tested to U.S. and Canadian Standards Polyamide Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Interior and Exterior Dual Finish Options Two Year Manufacturer's Warranty Thermal Break Single Hung Window Exterior Interior For specific product applications, Consult your Kawneer representative.
8 8 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG WINDOW CLASS and GRADE TESTING METHOD CLASS AW-PG50-H AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) FRAME DEPTH TYPICAL WALL THICKNESS 4-5/8" Overall Frame Depth 0.070" Nominal TYPICAL MAXIMUM WINDOW SIZE 60" X 99" TYPICAL MINIMUM WINDOW SIZE 24" X 6" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" and 1-1/2" STANDARD HARDWARE Heavy Duty Balances White Bronze Sweep Locks Sash Stops OPTIONAL HARDWARE Sill Auto Locks OTHER OPTIONS Between the Glass Muntins Historic Beveled Exterior Glazed-in Muntins (1-1/2" max. overall thickness) Exterior and Interior Tape Applied Muntins Perimeters and Sills Exterior Pannings and Interior Trims True Intermediate Muntin Structural Mullions Male /Female horizontally stacked H-Mullion for vertical stacking Tri-lite Configuration Strap Anchors
9 JULY, 2014 AA 5450 Ultra Thermal Window SINGLE HUNG WINDOW 9 SCALE : " = 1'-0" 4-5/8" AA 5450 SINGLE HUNG WINDOW (1" Double Glazed) 1 HEAD 1-11/16" HORIZONTAL 10 PSF 2" -1/16" 4 5 TYPICAL ELEVATION Log onto www. for other configurations 4-5/8" 2-9/16" -/4" 2-9/16" 4-5/8" 10 PSF (Panning Fin) 15 PSF VARIES -1/16" 4-1/16" FIXED JAMB OPERABLE JAMB Note: 15 PSF Sill also available with panning fin.
10 10 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG WINDOW SCALE : " = 1'-0" 4-5/8" AA 5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed) 1 HEAD 1-11/16" HORIZONTAL 10 PSF 2" -1/16" TYPICAL ELEVATION Log onto www. for other configurations 4-5/8" 2-9/16" 4 5 -/4" 2-9/16" 4-5/8" 10 PSF (Panning Fin) 15 PSF VARIES -1/16" 4-1/16" FIXED JAMB OPERABLE JAMB Note: 15 PSF Sill also available with panning fin.
11 JULY, 2014 AA 5450 Ultra Thermal Window SINGLE HUNG WINDOW 11 SCALE : " = 1'-0" 4-5/8" AA 5450 SINGLE HUNG WINDOW (Tri-Lite 1" Double Glazed) HEAD 2 HORIZONTAL 2 HORIZONTAL 1-11/16" 2-1/2" 2" 6 4-5/8" 4 TYPICAL ELEVATION Log onto www. for other configurations 2-9/16" 4-5/8" 10 PSF 15 PSF -1/16" 4-1/16" Note: 10 PSF Sill also available with panning fin. 2-9/16" -/4" Note: 15 PSF Sill also available with panning fin. 4 5 FIXED JAMB OPERABLE JAMB
12 12 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG WINDOW SCALE : " = 1'-0" 4-5/8" 4-5/8" AA 5450 SINGLE HUNG WINDOW (Tri-Lite 1-1/2" Triple Glazed) TYPICAL ELEVATION Log onto www. for other configurations 2-9/16" 6 -/4" 2-9/16" 4-5/8" HEAD 2 HORIZONTAL 10 PSF 15 PSF HORIZONTAL 1-11/16" 4-1/16" -1/16" 2" 2-1/2" Note: 10 PSF Sill also available with panning fin. Note: 15 PSF Sill also available with panning fin. 4 5 FIXED JAMB OPERABLE JAMB
13 JULY, 2014 AA 5450 Ultra Thermal Window SINGLE HUNG WINDOW 1 HEAVY DUTY BALANCES A class 5 adjustable spiral balance with excellent operating forces capable of balancing heavier sash weights. The balance utilizes stainless steel components and is cycle tested for longevity. SWEEP LOCK AND KEEPER AUTO LOCK White Bronze sweep locks and keepers with a durable brushed nickel finish and cycle tested for longevity. An optional spring operated auto lock conveniently located under the sash lift handle or an optional white bronze spring operated autolock located on the handle. The lock automatically engages the integral sill keeper upon closing the sash. COVERED WEEPS SASH CAMS SASH STOPS Weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black and white finishes. Adjustable glass filled nylon cams located left and right on the sash ensure proper alignment and smooth operation. Black rigid vinyl sash stops are inserted into the vertical jambs without exposed fasteners to prevent excessive sash travel.
14 14 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG WINDOW Standard Features High Performance Architectural Grade Window Tested to U.S. and Canadian Standards Polyamide Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Interior and Exterior Dual Finish Options Two Year Manufacturer's Warranty Thermal Break Double Hung Window Exterior Interior For specific product applications, Consult your Kawneer representative.
15 JULY, 2014 AA 5450 Ultra Thermal Window DOUBLE HUNG WINDOW 15 CLASS and GRADE TESTING METHOD CLASS AW-PG50-H AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) FRAME DEPTH TYPICAL WALL THICKNESS 4-5/8" Overall Frame Depth 0.070" Nominal TYPICAL MAXIMUM WINDOW SIZE 60" X 99" TYPICAL MINIMUM WINDOW SIZE 24" X 6" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" and 1-1/2" STANDARD HARDWARE Heavy Duty Balances Zinc Die Cast Sweep Locks Sash Stops Aluminum Upper Sash Auto Lock OPTIONAL HARDWARE Aluminum or White Bronze Sill Auto Locks OTHER OPTIONS Between the Glass Muntins Historic Beveled Exterior Glazed-in Muntins (1-1/2" max. overall thickness) Exterior and Interior Tape Applied Muntins Perimeters and Sills Exterior Pannings and Interior Trims True Intermediate Muntin Structural Mullions Male/Female horizontally stacked H-Mullion for vertical stacking Strap Anchors
16 16 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG WINDOW SCALE : " = 1'-0" 4-5/8" AA 5450 DOUBLE HUNG WINDOW 1 (1" Double Glazed) HEAD 2-1/16" 1-/4" HORIZONTAL 10 PSF 2" -1/16" 4-5/8" TYPICAL ELEVATION Log onto www. for other configurations 1-1/16" -/4" 4 5 JAMB JAMB -/4" 1-1/16" 4-5/8" 10 PSF (Panning Fin) 15 PSF VARIES -1/16" 4-1/16" Note: 15 PSF Sill also available with panning fin.
17 JULY, 2014 AA 5450 Ultra Thermal Window DOUBLE HUNG WINDOW 17 SCALE : " = 1'-0" 4-5/8" AA 5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed) 1 HEAD 2-1/16" 1-/4" HORIZONTAL 10 PSF 2" -1/16" 4-5/8" TYPICAL ELEVATION Log onto www. for other configurations 1-1/16" -/4" 4 5 -/4" 1-1/16" 4-5/8" 10 PSF (Panning Fin) 15 PSF VARIES -1/16" 4-1/16" FIXED JAMB OPERABLE JAMB Note: 15 PSF Sill also available with panning fin.
18 18 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG WINDOW SCALE : " = 1'-0" 4-5/8" AA 5450 DOUBLE HUNG WINDOW (Tri-Lite 1" Double Glazed) 1 HEAD 1-11/16" HORIZONTAL HORIZONTAL 4-1/8" 2" 6 4-5/8" 4 TYPICAL ELEVATION Log onto www. for other configurations 2-9/16" 4-5/8" 4 10 PSF 4 15 PSF -1/16" 4-1/16" Note: 10 PSF Sill also available with panning fin. 2-9/16" -/4" 5 6 FIXED JAMB OPERABLE JAMB Note: 15 PSF Sill also available with panning fin.
19 JULY, 2014 AA 5450 Ultra Thermal Window DOUBLE HUNG WINDOW 19 SCALE : " = 1'-0" 4-5/8" AA 5450 DOUBLE HUNG WINDOW (Tri-Lite 1-1/2" Double Glazed) 1 HEAD 1-11/16" HORIZONTAL 2 HORIZONTAL 4-1/8" 2" 6 4-5/8" 4 TYPICAL ELEVATION Log onto www. for other configurations 2-9/16" 4-5/8" 10 PSF 15 PSF -1/16" Note: 10 PSF Sill also available with panning fin. 4-1/16" 2-9/16" -/4" 4 5 FIXED JAMB OPERABLE JAMB Note: 15 PSF Sill also available with panning fin.
20 20 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG WINDOW HEAVY DUTY BALANCES A class 5 adjustable spiral balance with excellent operating forces capable of balancing heavier sash weights. The balance utilizes stainless steel components and is cycle tested for longevity. SWEEP LOCK AND KEEPER AUTO LOCK AND KEEPER White Bronze sweep locks and keepers with a durable brushed nickel finish and cycle tested for longevity. An aluminum spring operated auto lock located on the upper sash. The lock automatically engages the integral keeper securing the sash in the closed position. The auto lock is an option for the lower sash, but is standard for the upper sash. COVERED WEEPS SASH CAMS SASH STOPS A weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black and white finishes. Adjustable glass filled nylon cams located left and right on the sash ensure proper alignment and smooth operation. Black rigid vinyl sash stops are inserted into the vertical jambs without exposed fasteners to prevent excessive sash travel.
21 JULY, 2014 AA 5450 Ultra Thermal Window DOUBLE HUNG WINDOW 21 UPPER SASH SNAP LOCK A White Bronze spring operated auto lock located on the upper sash. The lock automatically engages the integral keeper securing the upper sash in the closed position. The snap lock is an option for the upper sash. WHITE BRONZE AUTO LOCK A White Bronze spring operated auto lock located on the lower sash. The lock automatically engages the integral keeper securing the lower sash in the closed position. The auto lock is an option for the lower sash.
22 22 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDING WINDOW Standard Features High Performance Architectural Grade Window Tested to U.S. and Canadian Standards Polyamide Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Interior and Exterior Dual Finish Options Two Year Manufacturer's Warranty Thermal Break Horizontal Sliding Window Exterior Interior For specific product applications, Consult your Kawneer representative.
23 JULY, 2014 AA 5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW 2 CLASS and GRADE TESTING METHOD CLASS AW-PG50-HS AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) FRAME DEPTH TYPICAL WALL THICKNESS 4-5/8" Overall Frame Depth 0.070" Nominal TYPICAL MAXIMUM WINDOW SIZE 99"X 79" TYPICAL MINIMUM WINDOW SIZE 6" X 24" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" and 1-1/2" STANDARD HARDWARE OPTIONAL HARDWARE White Bronze Sweep Locks Sash Stops Aluminum Sash Auto Lock (At XX Inactive Sash) Aluminum Auto Locks OTHER OPTIONS Between the Glass Muntins Historic Beveled Exterior Glazed-in Muntins (1-1/2" max. overall thickness) Exterior and Interior Tape Applied Muntins Perimeters and Sills Exterior Pannings and Interior Trims Piece Structural Mullions Male/Female horizontally stacked H-Mullion for vertical stacking Strap Anchors
24 24 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDING WINDOW OX HORIZONTAL SLIDING WINDOW (Keyed to details on pages 25 and 26) TYPICAL ELEVATION Log onto www. for other configurations 4 7
25 JULY, 2014 SCALE : " = 1'-0" AA 5450 Ultra Thermal Window OX HORIZONTAL SLIDING WINDOW (1" Double Glazed) HORIZONTAL SLIDING WINDOW /8" 1 FIXED HEAD 2 FIXED 10 PSF -2/2" 2-9/16" SLIDING HEAD 4 SLIDING 10 PSF 4-7/8" 2-9/16" 2A FIXED 10 PSF (Panning Fin) -2/2" 4A SLIDING 10 PSF (Panning Fin) 4-7/8" 1-11/16" 2" 2-1/16" FIXED JAMB INTERLOCKS SLIDING JAMB
26 26 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDING WINDOW SCALE : " = 1'-0" OX HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed) 4-5/8" 1 FIXED HEAD 2 FIXED 10 PSF -2/2" 2-9/16" SLIDING HEAD 4 SLIDING 10 PSF 4-7/8" 2-9/16" 2A FIXED 10 PSF (Panning Fin) -2/2" 4A SLIDING 10 PSF (Panning Fin) 4-7/8" 1-11/16" 2" 2-1/16" FIXED JAMB INTERLOCKS SLIDING JAMB
27 JULY, 2014 AA 5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW 27 XO HORIZONTAL SLIDING WINDOW (Keyed to details on pages 28 and 29) TYPICAL ELEVATION Log onto www. for other configurations 4 7
28 28 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDING WINDOW SCALE : " = 1'-0" XO HORIZONTAL SLIDING WINDOW (1" Double Glazed) 4-5/8" 1 SLIDING HEAD 2 SLIDING 10 PSF 4-7/8" 2-9/16" FIXED HEAD 4 FIXED 10 PSF -2/2" 2-9/16" 2A SLIDING 10 PSF (Panning Fin) 4-7/8" 4A FIXED 10 PSF (Panning Fin) -2/2" 2-1/16" 2" 1-11/16" SLIDING JAMB INTERLOCKS FIXED JAMB
29 JULY, 2014 SCALE : " = 1'-0" AA 5450 Ultra Thermal Window XO HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed) HORIZONTAL SLIDING WINDOW /8" 1 SLIDING HEAD 2 SLIDING 10 PSF 4-7/8" 2-9/16" FIXED HEAD 4 FIXED 10 PSF -2/2" 2-9/16" 2A SLIDING 10 PSF (Panning Fin) 4-7/8" 4A FIXED 10 PSF (Panning Fin) -2/2" 2-1/16" 2" 1-11/16" SLIDING JAMB INTERLOCKS FIXED JAMB
30 0 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDING WINDOW XX HORIZONTAL SLIDING WINDOW (Keyed to details on pages 1 and 2) TYPICAL ELEVATION Log onto www. for other configurations 4 7
31 JULY, 2014 SCALE : " = 1'-0" AA 5450 Ultra Thermal Window XX HORIZONTAL SLIDING WINDOW (1" Double Glazed) HORIZONTAL SLIDING WINDOW 1 4-5/8" 1 SLIDING HEAD 2 SLIDING 10 PSF 4-7/8" -/4" SLIDING HEAD 4 SLIDING 10 PSF 4-7/8" -/4" 2A SLIDING 10 PSF (Panning Fin) 4-7/8" 4A SLIDING 10 PSF (Panning Fin) 4-7/8" 2-1/16" 2" 2-1/16" 5 6 SLIDING JAMB INTERLOCKS 7 SLIDING JAMB
32 2 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDING WINDOW SCALE : " = 1'-0" XX HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed) 4-5/8" 1 SLIDING HEAD 2 SLIDING 10 PSF 4-7/8" -/4" SLIDING HEAD 4 SLIDING 10 PSF 4-7/8" -/4" 2A SLIDING 10 PSF (Panning Fin) 4-7/8" 4A SLIDING 10 PSF (Panning Fin) 4-7/8" 2-1/16" 2" 2-1/16" 5 6 SLIDING JAMB INTERLOCKS 7 SLIDING JAMB
33 JULY, 2014 AA 5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW COMPOSITE ADJUSTABLE TANDEM ROLLER Glass filled nylon housing, die cast zamak roller support, precision sealed ball bearing rollers with nylon tires. SWEEP LOCK AND KEEPER AUTO LOCK AND KEEPER White Bronze sweep locks and keepers with a durable brushed nickel finish and cycle tested for longevity. An aluminum spring operated auto lock. The lock automatically engages the integral keeper securing the sash in the closed position. The auto lock is an option for the jamb sash. COVERED WEEPS A weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black and white finishes.
34 4 AA 5450 Ultra Thermal Window JULY, 2014 WINDLOAD CHARTS THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/ increase in allowable stress has not been used to develop these curves. MULLION HEIGHT IN FEET MULLION CENTERS IN METERS MULLION CENTERS IN FEET A B C 2.0 D E MULLION HEIGHT IN METERS IF-149 IF-181 A = 15 PSF (720) B = 20 PSF (960) C = 25 PSF (1200) D = 0 PSF (1440) E = 5 PSF (1920) H IF-149 IF-181 WINDLOAD CHARTS ARE BASED ON COMPOSITE PROPERTIES WHICH ARE CALCULATED IN ACCORDANCE WITH AAMA TIR-8 AND AAMA 505 MULLION HEIGHT IN FEET MULLION CENTERS IN METERS A 10.0 B 9 C 8 D E MULLION CENTERS IN FEET MULLION HEIGHT IN METERS UNITS WITH HORIZONTALS UNITS WITHOUT HORIZONTALS MULLION CENTERS IN METERS MULLION HEIGHT IN FEET A B C 2.0 D E MULLION CENTERS IN FEET MULLION HEIGHT IN METERS IF-152 A = 15 PSF (720) B = 20 PSF (960) C = 25 PSF (1200) D = 0 PSF (1440) E = 5 PSF (1920) H IF-152 WINDLOAD CHARTS ARE BASED ON COMPOSITE PROPERTIES WHICH ARE CALCULATED IN ACCORDANCE WITH AAMA TIR-8 AND AAMA 505 MULLION CENTERS IN METERS A 10.0 B 9 C 8 D 7 E MULLION HEIGHT IN FEET MULLION CENTERS IN FEET MULLION HEIGHT IN METERS UNITS WITH HORIZONTALS UNITS WITHOUT HORIZONTALS
35 JULY, 2014 SCALE : " = 1'-0" AA 5450 Ultra Thermal Window RECEPTOR DETAILS RECEPTORS 5 5-7/16" IF /2" 1-/16" 1-/4" IF S /4" /2" IF-144 S-071 2" INTERIOR GLAZED 2-1/2" 1-/16" 1-/4" S-1108 IF /16" 5- IF /4" /2" IF-1451 S-071 2" EXTERIOR GLAZED
36 6 AA 5450 Ultra Thermal Window JULY, 2014 ANCHORS ANCHOR DETAILS NOTE: Interior glazed shown, exterior glazed similar IF-1442 S-1108 IF /4" 2-11/2" STRAP ANCHOR WITH RECEPTOR S-071 IF /16" 1-15/16" STRAP ANCHOR WITHOUT RECEPTOR
37 JULY, 2014 AA 5450 Ultra Thermal Window FIXED WINDOW THERMAL CHARTS 7 Generic Project Specific U-factor Example Calculation (Percent of glass will vary on specific products depending on sitelines) '-0" (915) 5'-0" (1524) 2- (822) 56- (142) Example Glass U-Factor = 0.42 Btu/hr ft 2 F Total Daylight Opening = = 12.67ft 2 Total Projected Area = '-0" 5'-0" = 15 ft 2 Percent of Glass System U-factor vs Percent of Glass Area = (Total Daylight Opening Total Projected Area)100 = ( )100 = 85% EXAMPLE NOT FOR DESIGN U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.44 Btu hr ft 2 F System U-factor 0.85 Percent of Glass Area Based on 85% glass and center of glass () U-factor of 0.42 System U-factor is equal to 0.44 Btu/hr ft 2 F
38 8 AA 5450 Ultra Thermal Window JULY, 2014 FIXED WINDOW THERMAL CHARTS Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 FIXED WINDOW (1" Double Glazed) U-factor 0.47 (2.67) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) System U-factor vs Percent of Glass Area (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) Btu hr ft 2 F System U-factor 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
39 JULY, 2014 AA 5450 Ultra Thermal Window AA 5450 FIXED WINDOW (1" Double Glazed) FIXED WINDOW THERMAL CHARTS 9 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area System VT Vision Area / Total Area (%)
40 40 AA 5450 Ultra Thermal Window JULY, 2014 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor AA 5450 FIXED WINDOW (1" Double Glazed) NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall SHGC 4 Glass VT Overall VT
41 JULY, 2014 Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 Ultra Thermal Window AA 5450 FIXED WINDOW (1-1/2" Triple Glazed) FIXED WINDOW THERMAL CHARTS 41 U-factor 0.2 (1.82) (1.71) System U-factor vs Percent of Glass Area 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) Btu hr ft 2 F System U-factor 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
42 42 AA 5450 Ultra Thermal Window JULY, 2014 FIXED WINDOW THERMAL CHARTS AA 5450 FIXED WINDOW (1-1/2" Triple Glazed) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area System VT Vision Area / Total Area (%)
43 JULY, 2014 AA 5450 Ultra Thermal Window FIXED WINDOW THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA 5450 FIXED WINDOW (1-1/2" Triple Glazed) 4 Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall Glass U-Factor 4 Glass VT Overall VT NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16")
44 44 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG WINDOW THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of glass will vary on specific products depending on sitelines) '-0" (915) 1-7/16" (799) 5'-0" (1524) 29-5/16" (745) Example Glass U-Factor = 0.42 Btu/hr ft 2 F 25-/4" (654) 25-/4" (654) Total Daylight Opening = (1-7/16" 25-/4") + (29-5/16" 25-/4") = ft 2 Total Projected Area = '-0" 5'-0" = 15 ft 2 Percent of Glass = (Total Daylight Opening Total Projected Area)100 = ( )100 = 72% System U-factor vs Percent of Glass Area 0.90 U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) EXAMPLE NOT FOR DESIGN Btu hr ft 2 F System U-factor % Percent of Glass Area Based on 72% glass and center of glass () U-factor of 0.42 System U-factor is equal to 0.49 Btu/hr ft 2 F
45 JULY, 2014 Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 Ultra Thermal Window AA 5450 SINGLE HUNG WINDOW (1" Double Glazed - 10lb. Sill) SINGLE HUNG THERMAL CHARTS 45 U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) System U-factor vs Percent of Glass Area (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) Btu hr ft 2 F System U-factor (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
46 46 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG THERMAL CHARTS AA 5450 SINGLE HUNG WINDOW (1" Double Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area System VT Vision Area / Total Area (%)
47 JULY, 2014 AA 5450 Ultra Thermal Window SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) 47 Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor AA 5450 SINGLE HUNG WINDOW (1" Double Glazed - 10ib. Sill) NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall SHGC 4 Glass VT Overall VT
48 48 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb. Sill) U-factor 0.2 (1.82) System U-factor vs Percent of Glass Area (1.71) 0.28 (1.59) 0.26 (1.48) Btu hr ft 2 F System U-factor 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
49 JULY, 2014 AA 5450 Ultra Thermal Window AA 5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb Sill) SINGLE HUNG THERMAL CHARTS 49 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area System VT Vision Area / Total Area (%)
50 50 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA 5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall Glass U-Factor 4 Glass VT Overall VT NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16").
51 JULY, 2014 Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 Ultra Thermal Window AA 5450 SINGLE HUNG WINDOW (1" Double Glazed - 15lb. Sill) SINGLE HUNG THERMAL CHARTS 51 U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) System U-factor vs Percent of Glass Area (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) (0.57) Btu hr ft 2 F System U-factor Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
52 52 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG THERMAL CHARTS AA 5450 SINGLE HUNG WINDOW (1" Double Glazed - 15lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area System VT Vision Area / Total Area (%)
53 JULY, 2014 AA 5450 Ultra Thermal Window SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) 5 Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor AA 5450 SINGLE HUNG WINDOW (1" Double Glazed - 15lb Sill) NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall SHGC 4 Glass VT Overall VT
54 54 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb. Sill) U-factor System U-factor vs Percent of Glass Area 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) Btu hr ft 2 F System U-factor 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
55 JULY, 2014 AA 5450 Ultra Thermal Window AA 5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb Sill) SINGLE HUNG THERMAL CHARTS 55 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area System VT Vision Area / Total Area (%)
56 56 AA 5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA 5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb. Sill) Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall Glass U-Factor 4 Glass VT Overall VT NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16").
57 JULY, 2014 AA 5450 Ultra Thermal Window '-0" (915) 28-1/2" (724) DOUBLE HUNG WINDOW THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of glass will vary on specific products depending on sitelines) 57 5'-0" (1524) Example Glass U-Factor = 0.42 Btu/hr ft 2 F 25-11/16" (652) 25-11/16" (652) Total Daylight Opening = (28-1/2" 25-11/16") + (28-1/2" 25-11/16") = ft 2 Total Projected Area = '-0" 5'-0" = 15 ft 2 Percent of Glass = (Total Daylight Opening Total Projected Area)100 = ( )100 = 68% System U-factor vs Percent of Glass Area U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) EXAMPLE NOT FOR DESIGN Btu hr ft 2 F System U-factor % Percent of Glass Area Based on 68% glass and center of glass () U-factor of 0.42 System U-factor is equal to 0.49 Btu/hr ft 2 F
58 58 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 DOUBLE HUNG WINDOW (1" Double Glazed - 10lb. Sill) U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) (2.27) System U-factor vs Percent of Glass Area 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) (1.71) Btu hr ft 2 F System U-factor 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
59 JULY, 2014 AA 5450 Ultra Thermal Window AA 5450 SINGLE HUNG WINDOW (1" Double Glazed - 10lb Sill) DOUBLE HUNG THERMAL CHARTS 59 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area Vision Area / Total Area (%) System VT
60 60 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor AA 5450 DOUBLE HUNG WINDOW (1" Double Glazed - 10ib. Sill) NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 960mm wide by 2090mm high (7-/4" by 82-). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall SHGC 4 Glass VT Overall VT
61 JULY, 2014 Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 Ultra Thermal Window AA 5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb. Sill) DOUBLE HUNG THERMAL CHARTS 61 U-factor 0.2 (1.82) System U-factor vs Percent of Glass Area (1.71) 0.28 (1.59) 0.26 (1.48) Btu hr ft 2 F System U-factor 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
62 62 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG THERMAL CHARTS AA 5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area Vision Area / Total Area (%) System VT
63 JULY, 2014 AA 5450 Ultra Thermal Window DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA 5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb. Sill) 6 Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall Glass U-Factor 4 Glass VT Overall VT NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 960mm wide by 2090mm high (7-/4" by 82-).
64 64 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 DOUBLE HUNG WINDOW (1" Double Glazed - 15lb. Sill) U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) System U-factor vs Percent of Glass Area (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) Btu hr ft 2 F System U-factor (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
65 JULY, 2014 AA 5450 Ultra Thermal Window AA 5450 SINGLE HUNG WINDOW (1" Double Glazed - 15lb Sill) DOUBLE HUNG THERMAL CHARTS 65 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area Vision Area / Total Area (%) System VT
66 66 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor AA 5450 DOUBLE HUNG WINDOW (1" Double Glazed - 15ib. Sill) NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 960mm wide by 2090mm high (7-/4" by 82-). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall SHGC 4 Glass VT Overall VT
67 JULY, 2014 Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 Ultra Thermal Window AA 5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb. Sill) DOUBLE HUNG THERMAL CHARTS 67 U-factor 0.2 (1.82) System U-factor vs Percent of Glass Area (1.71) 0.28 (1.59) 0.26 (1.48) Btu hr ft 2 F System U-factor 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
68 68 AA 5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG THERMAL CHARTS AA 5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area Vision Area / Total Area (%) System VT
69 JULY, 2014 AA 5450 Ultra Thermal Window DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA 5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb. Sill) 69 Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall Glass U-Factor 4 Glass VT Overall VT NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 960mm wide by 2090mm high (7-/4" by 82-).
70 70 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SIDING WINDOW THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of glass will vary on specific products depending on sitelines) 5'-0" (1524) 28-9/16" (725) 26-/4" (679) 26-/4" (679) Example Glass U-Factor = 0.42 Btu/hr ft 2 F 29-2/2" (755) '-0" (915) Total Daylight Opening = (28-9/16" 26-/4") + (29-2/2" 26-/4") = 10.8 ft 2 Total Projected Area = '-0" 5'-0" = 15 ft 2 Percent of Glass = (Total Daylight Opening Total Projected Area)100 = ( )100 = 72% System U-factor vs Percent of Glass Area U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) % EXAMPLE NOT FOR DESIGN Percent of Glass Area Based on 72% glass and center of glass () U-factor of 0.42 System U-factor is equal to 0.49 Btu/hr ft 2 F Btu hr ft 2 F System U-factor
71 JULY, 2014 AA 5450 Ultra Thermal Window HORIZONTAL SLIDER THERMAL CHARTS 71 Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 OX / XO HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb. Sill) U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) (2.27) 0.8 (2.16) 0.6 (2.05) 0.4 (1.9) System U-factor vs Percent of Glass Area 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) (0.57) Btu hr ft 2 F System U-factor Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
72 72 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDER THERMAL CHARTS AA 5450 OX / XO HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area System VT Vision Area / Total Area (%)
73 JULY, 2014 AA 5450 Ultra Thermal Window HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) 7 Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor AA 5450 OX / XO HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb Sill) NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 1200mm high (59-1/16" by 47-1/4"). SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall SHGC 4 Glass VT Overall VT
74 74 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDER THERMAL CHARTS Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 OX / XO HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb. Sill) U-factor System U-factor vs Percent of Glass Area 0.2 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Btu hr ft 2 F System U-factor Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
75 JULY, 2014 AA 5450 Ultra Thermal Window HORIZONTAL SLIDER THERMAL CHARTS AA 5450 OX / XO HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb Sill) 75 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area SHGC Vision Area / Total Area (%) System SHGC VT System Visible Transmittance (VT) vs Percent of Vision Area System VT Vision Area / Total Area (%)
76 76 AA 5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA 5450 OX / XO HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor Overall U-Factor SHGC Matrix 2 Visible Transmittance 2 Glass SHGC Overall Glass U-Factor 4 Glass VT Overall VT NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC SHGC and VT values are determined in accordance with NFRC Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 1200mm high (59-1/16" by 47-1/4").
77 JULY, 2014 AA 5450 Ultra Thermal Window HORIZONTAL SLIDER THERMAL CHARTS 77 Note: Values in parentheses are metric. = Center of Glass. Charts are generated per AMMA 507 AA 5450 XX HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb. Sill) U-factor 0.48 (2.7) 0.46 (2.61) 0.44 (2.50) 0.42 (2.9) (2.27) 0.8 (2.16) System U-factor vs Percent of Glass Area 0.6 (2.05) 0.4 (1.9) 0.2 (1.82) (1.71) Btu hr ft 2 F System U-factor 0.28 (1.59) 0.26 (1.48) 0.24 (1.7) 0.22 (1.25) (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier.
Series 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window
Windows Curtain Walls Entrances Storefronts Series 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window Configurations XO OX XOX Fixed Series 3502 retains an AAMA
City of San Diego, CWP Guidelines
PART 1 -- GENERAL SECTION 08520-1.1 WORK OF THIS SECTION City of San Diego, CWP Guidelines A. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens,
ASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: Atrium Companies, Inc. SERIES/MODEL: 50/305 HS PRODUCT TYPE: Vinyl Horizontal Slider
ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: Atrium Companies, Inc. SERIES/MODEL: 50/305 HS PRODUCT TYPE: Vinyl Horizontal Slider Report No.: Test Date: 5/21/07 Through: 5/23/07 Report Date: 5/30/07
Providing the widest selection of quality vinyl and aluminum window & door products.
Providing the widest selection of quality vinyl and aluminum window & door products. KELTIC DOOR SERIES At International Window, quality is our trademark. That is why we leave nothing to chance. Today,
190/350/500 Standard Entrances
AUGUST, 2015 FEATURES 1 Features 190 narrow stile has 2-1/8" (54) vertical stile, 2-1/4" (57.2) top and 3-7/8" (98.4) bottom rail 350 medium stile has 3-1/2" (88.9) vertical stile, 3-1/2" (88.9) top and
TEST REPORT. Report No.: B3404.01-801-47. Rendered to: CROFT, LLC. Magnolia, Mississippi. PRODUCT TYPE: Aluminum Single Hung Window SERIES/MODEL: 95
Architectural Testing TEST REPORT Report No.: B3404.01-801-47 Rendered to: CROFT, LLC. Magnolia, Mississippi PRODUCT TYPE: Aluminum Single Hung Window SERIES/MODEL: 95 SPECIFICATION: AAMA/WDMA/CSA 101/I.S.2/A440-08,
SECTION 08560 SERIES 1500 VINYL PATIO DOORS
SERIES 1500 VINYL PATIO DOORS PART 1 GENERAL 1.1 SECTION INCLUDES A. Patio Doors 1.2 RELATED SECTIONS A. Section 05450: Cold Formed Metal Framing. B. Section 06100: Rough Carpentry. C. Section 06200: Finish
SECTION 08 53 13 VINYL WINDOWS. A. The General Conditions, Supplementary Conditions, and Division 01 - Requirements apply.
SECTION 08 53 13 VINYL WINDOWS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 - Requirements apply. 1.2 SECTION INCLUDES A. Double
WINDOW PANNING AND TRIMS
OCTOBER, 2010 PANNING AND TRIMS GENERAL INFORMATION 1 EXTERIOR PANNING Panning is primarily used to cover the perimeters of existing building openings prior to the installation of replacement windows.
RAM Industries 8600 Commerce Park Dr Houston, TX 77036 Tel: 281-495-9056 Fax: 281-495-6778 www.ramwindows.com
SERIES 900 CASEMENT WINDOW Page 1 of 6 RAM Industries 8600 Commerce Park Dr Houston, TX 77036 Tel: 281-495-9056 Fax: 281-495-6778 www.ramwindows.com SPECIFICATION GUIDE SERIES 900 CASEMENT WINDOW RAM Industries
Strength, Style and Security for your home and family
Strength, Style and Security for your home and family NEW and IMPROVED DOORS 2013 John Cannon Homes, Inc. The Amarina Why Sentinel Impact Resistant Windows and Doors? Sentinel by CGI has received the prestigious
PERFORMANCE TEST REPORT. Rendered to: UNITED STATES ALUMINUM CORPORATION. SERIES/MODEL: 450 Center Glaze PRODUCT TYPE: Aluminum Curtain Wall
Architectural Testing PERFORMANCE TEST REPORT Rendered to: UNITED STATES ALUMINUM CORPORATION SERIES/MODEL: 450 Center Glaze PRODUCT TYPE: Aluminum Curtain Wall Title Summary of Results Air Infiltration
PERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY
PERFORMANCE TEST REPORT Rendered to: GLASSCRAFT DOOR COMPANY SERIES/MODEL: Buffalo Forge Steel Doors / Round Top Single PRODUCT TYPE: In-swing Round Top Single Door RH-4 Title Uniform Load Deflection Test
Garden Windows Builders Vinyl
TABLE OF CONTENTS Specifications... 8-2 QuickSpecGuide... 8-3 Elevations/Sizes: 1/4 Scale GardenUnits... 8-4 Grille Patterns... 8-5 SectionDetails: 6 Scale... 8-6 December 2008 JELD-WEN reserves the right
TEST REPORT. Rendered to: INTERNATIONAL WINDOW Hayward, California. PRODUCT TYPE: Aluminum Hopper SERIES/MODEL: 7222
Architectural Testing TEST REPORT Report No.: C2375.01-301-44 Rendered to: INTERNATIONAL WINDOW Hayward, California PRODUCT TYPE: Aluminum Hopper SERIES/MODEL: 7222 SPECIFICATIONS: AAMA/WDMA/CSA 101/I.S.2/A440-05,
Window Installation Instructions
Caution The correct installation methods of windows in full frame or insert applications is critical towards achieving the tested performance of the window and longterm enjoyment and energy savings for
DESIGN AND CONSTRUCTION GUIDELINES AND STANDARDS DIVISION 8 DOORS AND WINDOWS 08 50 00 WINDOWS
SECTION INCLUDES Metal Windows Vinyl/Aluminum Clad Wood Windows Solid Fiberglass and Vinyl Windows Wood Windows (Historic Preservation only) RELATED SECTIONS 02 83 00 Lead Paint Remediation 06 10 00 Rough
NFRC 102-2010 THERMAL PERFORMANCE TEST REPORT. Rendered to: CR LAURENCE CO., INC. SERIES/MODEL: 7500 Concealed Vent TYPE: Projecting (Awning)
NFRC 102-2010 THERMAL PERFORMANCE TEST REPORT Rendered to: CR LAURENCE CO., INC. SERIES/MODEL: 7500 Concealed Vent TYPE: Projecting (Awning) Summary of Results Standardized Thermal Transmittance (U-Factor)
MIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Report No.: B8049.01-401-18. Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida
Architectural Testing MIAMI-DADE COUNTY PERFORMANCE TEST REPORT Report No.: B8049.01-401-18 Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida PRODUCT TYPE: Aluminum Storefront with Double Doors SERIES/MODEL:
JANUARY, 2016 TR-7100 Windows (Fixed) 1 EC 97909-071 085113 ALUMINUM WINDOWS Guide Specs
JANUARY, 2016 TR-7100 Windows (Fixed) 1 EC 97909-071 085113 ALUMINUM WINDOWS Guide Specs SECTION 085113 ALUMINUM WINDOWS This suggested guide specification has been developed using the current edition
CLAIM FORM APPENDIX. I. Photographs Identifying The Windows
CLAIM FORM APPENDIX I. Photographs Identifying The Windows The Settlement provides compensation for MIWD Products that are glazed with Glazing Tape and were manufactured or sold between July 1, 2000 and
Installation Detailed installation instructions are provided which should be strictly followed.
Specification System 6 The Metal Technology Thermally-Broken Vertical Slide Window has been designed in such a way that its'attractive and clean lines will enhance all types of residential and commercial
Series 456 Commercial Awning Window
Commercial Awning Window COMMERCIAL SERIES Photo courtesy of Hanlon Windows Australia DATE: MAY 2013 REPLACES: MARCH 2008 COMMERCIAL SERIES KEY FEATURES/PERFORMANCE CHARACTERISTICS Scale: not to scale
Introduction...COMB-2 Design Considerations and Examples...COMB-3
SECTION DIRECTORY General Information Introduction...COMB-2 Design Considerations and Examples...COMB-3 Combination Assembly Recommendations and Limitations Composite Configurations...COMB-4 Typical Sealant
Casement/Awning Window Parts Reference Catalog
Casement/Awning Window Parts Reference Catalog (Includes Miscellaneous Parts for Eyebrow Casement and Garden Bay Windows) #1028654 (Revised 03/02) Weather Shield Mfg., Inc. Medford, WI 54451 715/748-2100
Sample Calculations...V-CR-12. Door and Window Typical Combinations... V-CR-12 Horizontal and Vertical Typical Combinations...
SECTION DIRECTORY General Information Definitions...V-CR- Design Considerations...V-CR- Composite Configurations...V-CR-4 Design Considerations and Examples for Typical Window and Door Combinations...V-CR-5
How To Test For An Architectural Test
Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: CORAL ARCHITECTURAL PRODUCTS SERIES/MODEL: PW 256 with Door Openings PRODUCT TYPE: Aluminum Impact Resistant Curtain Wall System
SECTION REFERENCE. Tilt-Wash Double-Hung. Insert Windows. 400 Series
SECTION REFERENCE Size Ranges... 96 Existing Window Measurements... 96 Divided Light Patterns... 97 Window Details... 97 Joining Details... 97 Performance Data... 269 400 Series Windows TILT-WASH DOUBLE-HUNG
Glossary. 1/3 1/3 1/3 - Configuration of a vent-fixed-vent (xox) window in which the vents and fixed panel are equal sizes
Glossary 1/3 1/3 1/3 - Configuration of a vent-fixed-vent (xox) window in which the vents and fixed panel are equal sizes 1/4 1/2 1/4 - Configuration of a vent-fixed-vent (xox) window in which the vents
In the Fall 2002 issue of HHE News I examined
Choosing Replacement Windows 1 For Your Home Mark Pierce In the Fall 2002 issue of HHE News I examined reasons for, and against, replacing older windows with new, energy efficient windows. That article
Residential Garage Door Terminology
A Air Infiltration: The leakage or passage of air through a door system Anodize: A hard non-corrosive oxide film on the surface of aluminum Astragal: A compressible or deformable seal provided on the bottom
Series 602 MAGNUM Sliding Window DESIGNER SERIES
Series 602 DESIGNER SERIES DATE: NOVEMBER 2009 REPLACES: AUGUST 2003 DESIGNER SERIES Series 602 KEY EATURES / PERORMANCE CHARACTERISTICS Scale: NOT TO SCALE Designed to complement our existing high quality
Specifying Windows. Performance Standards
1 Specifying Windows and ddoors Using Performance Standards 2 This program is registered with the AIA/CES for continuing professional education. As such, it does not include content that may be deemed
K200 SERIES(CW40) (Formerly #1300 Series) SLIDER/CENTER VENT SLIDER/ END VENT SLIDER 2 3/8 FRAME DEPTH FEATURES
K200 SERIES(CW40) (Formerly #1300 Series) SLIDER/CENTER VENT SLIDER/ END VENT SLIDER 2 3/8 FRAME DEPTH FEATURES 1.) Available Configurations -XO, OX, OXO, OR XOX 2.) Main frame / Sash -Fin seal wool pile
ASTM E 1886 / ASTM E 1996 AND ASTM E 283, ASTM E 330, ASTM E 331 TEST REPORT. Rendered to: BEKAERT SPECIALTY FILMS, LLC
ASTM E 1886 / ASTM E 1996 AND ASTM E 283, ASTM E 330, ASTM E 331 TEST REPORT Rendered to: BEKAERT SPECIALTY FILMS, LLC SERIES/MODEL: Panorama 8-mil Film PRODUCT TYPE: Fixed Window with Applied Film This
CLEAR-DIVISIONS CENTERFOLD
CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in
PART 1 PROJECT DESCRIPTION 1.01 GENERAL INFORMATION
Detailed Specifications for Window Replacement for the Metropolitan Sewer District of Greater Cincinnati Little Miami Wastewater Treatment Plant 225 Wilmer Ave. Cincinnati, OH 45226 Administration Building,
Replacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin
Replacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin americancraftsmanwindows.com Project Requirements: Failure to follow these instructions may void product
SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS. System 402 Flush-Glazed Screw Spline Storefront
PART 1 GENERAL 1.01 Work Included SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS System 402 Flush-Glazed Screw Spline Storefront A. Furnish and install aluminum architectural storefront system
MANCHESTER SERIES(SGD-R35) SLIDING GLASS DOOR 5 5/8 FRAME DEPTH
MANCHESTER SERIES(SGD-R35) SLIDING GLASS DOOR 5 5/8 FRAME DEPTH FEATURES 1.) Available Configurations -Sliding Glass Door -Geometric shapes -OX, XO, OXO, OXXO, XOO, OOX (as viewed from exterior) 2.) Main
Confort 160. Sliding Systems. Sapa Building System
Confort 160 Sliding Systems Sapa Building System Confort 160 is a high performance thermally insulated sliding window system, with a user-friendly slide action. The system, which has an attractive aesthetic
TEST REPORT. Rendered to: TFC A DIVISION OF CENTURION INDUSTRIES, INC. Garrett, Indiana
Architectural Testing TEST REPORT Report No.: D0162.02-201-44 Rendered to: TFC A DIVISION OF CENTURION INDUSTRIES, INC. Garrett, Indiana PRODUCT TYPE: Pressure Equalized Rainscreen SERIES/MODEL: 4 mm Composite
Tuscany Series Vinyl Replacement Windows 3-Part Specification
PART 1 - GENERAL SECTION 08 53 13 (Masterformat 2004 Edition) VINYL WINDOWS Tuscany is optimized for replacement applications but since it is available in multiple frame styles including nail-on fin frame,
Sun Windows General Information Sun New Construction Window Installation Instructions
Sun Windows General Information Section 1 G F H H H A. Apply Weather Resistive Barrier B. Apply Sill Flashing Tape C. Place Waterproof Sill Shims D. Caulk Back of Nail Fin Sides & Top, Set Window, Fasten
FEBRUARY, 2016 2500 UT Unitwall System 1 EC 97909-074 084413 GLAZED ALUMINUM CURTAIN WALLS Guide Specs
FEBRUARY, 2016 2500 UT Unitwall System 1 EC 97909-074 084413 GLAZED ALUMINUM CURTAIN WALLS Guide Specs Kawneer Company, Inc., 2015 SECTION 084413 GLAZED ALUMINUM CURTAIN WALLS This suggested guide specification
10, 40, 60, 80 and Additional Styles. Series. Series. Series. Series VINYL REPLACEMENT WINDOWS
Series 10, Series 40, Series 60, Series 80 and Additional Styles VINYL REPLACEMENT WINDOWS The Lansing Difference For more than 50 years, Lansing Building Products has set the standard for exceptional
SECTION 6. Glass Storefront Doors:
SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail
CLEAR-DIVISIONS VARIOFOLD
CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the
Enhancing The Beauty And Value Of Your Home. Exclusive Patio Door Collection. NORTH STAR PATIO DOOR COLLECTION Two-Panel Three-Panel Four-Panel
Enhancing The Beauty And Value Of Your Home. Exclusive Patio Door Collection. NORTH STAR PATIO DOOR COLLECTION Two-Panel Three-Panel Four-Panel Since 1985 North Star has been an industry leader in the
Installation Window Building In Details
Installation Window Building In Details INSTALLATION Photo courtesy of Rowe Aluminium DATE: NOVEMBER 2009 REPLACES: AUGUST 2003 INSTALLATION Installation Replaces: Scale: NOT TO SCALE Vantage snap-on couplers
Accessory Windows. Replacement and New Construction
Accessory Windows Replacement and New Construction Casement Things couldn t be easier with our beautiful and functional vinyl casement windows. There s no need to stretch to reach a top lock because the
SECTION 08 52 00 WOOD WINDOWS (ANDERSEN ARCHITECTURAL CASEMENT AND AWNING WINDOWS)
SECTION 08 52 00 ( ) PART 1 - GENERAL SPECIFIER NOTE: DATA CONTAINED IN THIS GUIDE SPEC IS ACCURATE AS OF AUGUST 2007. DUE TO ONGOING PRODUCT CHANGES, THIS DATA MAY CHANGE OVER TIME. CONSULT MANUFACTURER
Tundra Series Windows January 2016
Tundra Series Windows January 2016 New Construction Installation Instructions Nail Fin, J-Fin and Brickmold Aplications product. ATTENTION! Read and understand all installation instructions before installing
MOCK-UP TEST REPORT. Rendered to: TUBELITE, INC. PROJECT: 200 Series Curtain Wall Mock-Up
MOCK-UP TEST REPORT Rendered to: TUBELITE, INC. PROJECT: 200 Series Curtain Wall Mock-Up Report No: 85616.01-120-32 Test Completion Date: 01/15/09 Report Date: 02/11/09 Record Retention End Date: 01/15/13
vinyl replacement windows LOOKING FOR VINYL REPLACEMENT WINDOWS? Standard Features easy, trouble-free operation. window material formulated and
vinyl replacement windows LOOKING FOR VINYL REPLACEMENT WINDOWS? We are confident that we carry a style and size to suit your application. You can be sure that your investment will add value to your home,
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
EDD-401. Stationary Louver Dual Drainable Blade. Application and Design. Standard Construction
Application and Design is a weather louver designed to protect air intake and exhaust openings in building exterior walls. Design incorporates a drainable head member and stationary horizontal blades to
Important Information for Installer & Homeowner
Important Information for Installer & Homeowner Homeowner: Please keep this information for your records, do not discard! Installation Instructions for Wood Frame Construction Replacement (See other side
CLEAR-DIVISIONS APERTO
CLEAR-DIVISIONS Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS moveable glass wall system. The yellow highlighted areas in the
ALUMINUM Guide Spec: Standard Aluminum Windows & Doors
ALUMINUM Guide Spec: Standard Aluminum Windows & Doors Standard Aluminum Windows ALUMINUM WINDOWS - 08 51 13 With the thin lines that Migard s Aluminum Windows provide, they are ideal for both new construction
Astragal: a vertical member placed at the meeting edges of a double door to provide a weather seal and may be used to anchor the fixed door.
Window and Door Dictionary AAMA: American Architectural Manufacturers Association. A national trade association that establishes voluntary standards for the window, door, and skylight industry. Ambient
Clad Direct Glaze Window Installation Instructions
Clad Direct Glaze Window Installation Instructions Sill flashing and sealing: 2. An overview of the proper flashing sequence is shown in figure 1. Please read entire installation instructions carefully
SHIELD NATIONAL OFFICE MELBOURNE 2-4 Freight Drive, Somerton, VIC 3062 Ph: 03 8339 2252
SHIELD NATIONAL OFFICE MELBOURNE 2-4 Freight Drive, Somerton, VIC 3062 Ph: 03 8339 2252 SHIELD DOORS & SYDNEY 4 Alban Street, Lidcombe NSW 2141 Ph: 02 9748 7005 UPTONS HOBART 312 Argyle Street, North Hobart,
Quality Building Products for over 50 Years
Light Commercial Quality Building Products for over 50 Years Harvey Building Products is a leading manufacturer and distributor of high quality building products. We manufacture a complete line of superior
TEST REPORT. Report No.: A9814.01 109 44. Rendered to: BAMCO INC. Middlesex, New Jersey. PRODUCT TYPE: Wall Cladding System SERIES/MODEL: Dry Concept
Architectural Testing TEST REPORT Report No.: A9814.01 109 44 Rendered to: BAMCO INC. Middlesex, New Jersey PRODUCT TYPE: Wall Cladding System SERIES/MODEL: Dry Concept AAMA 508 07, Voluntary Test Method
Garden Window. Montecito Series Vinyl Garden Window Architectural Manual
Montecito Series Vinyl The offers the outstanding insulating properties, low maintenance, and contemporary aesthetic appeal only vinyl can provide. Available in White and Tan homogenous window frames,
Table of Contents PART 1 WINDOW SELECTION GUIDE. Window and Door Selection Guide
VOLUME 1 - WINDOWS AND DOORS Window and Door Selection Guide PART 1 WINDOW SELECTION GUIDE WSG-11 PART 2 - PERFORMANCE SPECIFICATIONS Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows
INSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nailing fin. While the use of these installation instructions
Glossary. Argon: An inert, nontoxic gas used in insulating glass units to reduce heat transfer.
Glossary AAMA : American Architectural Manufacturers Association, a national trade association that established voluntary standards for the window, door and skylight industry. Argon: An inert, nontoxic
Basement Window Installation Guide Hopper and Sliding
Basement Window Installation Guide Hopper and Sliding americancraftsmanwindows.com Project Requirements: Installation must comply with all applicable building codes. Existing window frame, wall and weatherresistant
Insider Tips for Purchasing Replacement Windows
Insider Tips for Purchasing Replacement Windows From the experts at Legacy Remodeling WE SPEAK REMODELING Table of Contents Introduction Page 3 Window Styles Page 4 Window Materials Page 6 Window Efficiency
PERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY
Architectural Testing PERFORMANCE TEST REPORT Rendered to: GLASSCRAFT DOOR COMPANY SERIES/MODEL: Mahogany Entry Door PRODUCT TYPE: 6' x 8' Double Outswing Hardwood TDL Door with Half Circle TDL Transom
WINDOWS AND PATIO DOORS
LAKE BARRINGTON COMMUNITY HOMEOWNERS ASSOCIATION 64 Old Barn Road Lake Barrington, Illinois 60010 Phone: 847-382-1660 Fax: 847-382-2731 HOMEOWNER APPLICATION FOR ARCHITECTURAL REVIEW WINDOWS AND PATIO
Confort 26. Sliding Systems. Sapa Building System
Confort 26 Sliding Systems Sapa Building System Confort 26 is Sapa s thermally insulated sliding system for windows and doors. Available as two- and three-rail solution. Among its features, there are
Designed for Your Life. Guaranteed. Premium Vinyl. Replacement Windows. and Patio Doors
5000SERIES Designed for Your Life. Guaranteed. Premium Vinyl Replacement Windows and Patio Doors 5000SERIES It s time to meet the window designed for your life. Welcome top-of-the-line energy efficiency
Replacement Installation Instructions
Sliding Door Replacement Installation Instructions Please make sure you have: Fixed 1 - Operating (X) Panel (Glazing Bead Inside, Roller Adjustment Holes Outside) 1 - Fixed (O) Panel (For 3-Panel doors,
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
THE ULTIMATE HIGH PERFORMANCE REPLACEMENT WINDOWS AND PATIO DOORS
THE ULTIMATE HIGH PERFORMANCE REPLACEMENT WINDOWS AND PATIO DOORS EXCLUSIVELY BY NORANDEX Put our reputation in your home. At Norandex, we are proud to be a wellrespected leader in the home improvement
WINDOW INSTALLATION GUIDE
WINDOW INSTALLATION GUIDE is not responsible for or liable for any use or misuse of the information contained in this window installation guide. Window Installation Guide This guide provides basic information
BLOWING DUST INFILTRATION TEST REPORT. Rendered to: TEX-STAR WINDOWS, INC. PROJECT: Blowing Dust Test SERIES: 3000 Horizontal Sliding Window
BLOWING DUST INFILTRATION TEST REPORT Rendered to: TEX-STAR WINDOWS, INC. PROJECT: Blowing Dust Test SERIES: 3000 Horizontal Sliding Window Report No: 99463.01-801-44 Test Completion Date: 03/24/10 Report
Section 08520 - Aluminum Windows (4600 Series Specifications)
Section 08520 - Aluminum Windows (4600 Series Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for
foot skylight) is enough to knock a worker off their feet. A 10 mph wind gust on a 5 x 6 skylight develops a wind force of 270 lbs.
Skylight Installation Instructions This document provides instruction and guidelines for installation of both curb mount (CM) and self flashing (SF) unit skylights on flat, pitched (> or equal to 3/12
Reflections 5500. Vinyl Replacement Windows Reflections
Reflections 5500 Vinyl Replacement Windows Reflections 5500 Be greeted by an inspiring splash of sunlight. Be greeted by a symphony of style. Be greeted by an energy bill that makes you want to sing. What
Enhancing The Beauty And Value Of Your Home. Exclusive Patio Door Collection.
Enhancing The Beauty And Value f Your Home. Exclusive Patio Door Collection. Since 1985 North Star has been an industry leader in the manufacture of attractive and energy-efficient vinyl windows and patio
Enhance. the beauty of your home. Vinyl Windows & Patio Doors Series 600 Series 1400 Series 2100. www.newtecwindow.com
www.newtecwindow.com Enhance the beauty of your home Vinyl Windows & Patio Doors Series 600 Series 1400 Series 2100 Manufacturer of Vinyl & Aluminum Windows Newtec Windows & Doors is a fast growing manufacturer
ASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: NORSE, INC.
Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: NORSE, INC. SERIES/MODEL: Flush Mount/Surface Mount PRODUCT TYPE: Hurricane Shutter Fastening System This report contains in its
PERFORMANCE TEST REPORT. Rendered to: TREMCO INCORPORATED. SERIES/MODEL: Proglaze ETA PRODUCT TYPE: Engineered Transition Assembly
PERFORMANCE TEST REPORT Rendered to: TREMCO INCORPORATED SERIES/MODEL: Proglaze ETA PRODUCT TYPE: Engineered Transition Assembly Title Summary of Results Air Infiltration
AAMA/WDMA/CSA 101/I.S.2/A440-05 TEST REPORT. Rendered to: EAGLE WINDOW & DOOR COMPANY
Architectural Testing AAMA/WDMA/CSA 101/I.S.2/A440-05 TEST REPORT Rendered to: EAGLE WINDOW & DOOR COMPANY SERIES/MODEL: Series 01 Axiom Clad One-Piece Casement Fixed 6060 PRODUCT TYPE: Aluminum Clad Fixed
Impact-Resistant Windows and Sliding Glass Doors
Impact-Resistant Windows and Sliding Glass Doors Make Your Home A SafeHarbor. SafeHarbor Impact-Resistant Windows and Sliding Glass Doors are designed to look like traditional windows and doors, but they
SECTION 08600 POLYVINYL CHLORIDE (PVC) WINDOWS Paradigm Window Solutions 8381 Single Hung
SECTION 08600 POLYVINYL CHLORIDE (PVC) WINDOWS Paradigm Window Solutions 8381 Single Hung PART 1 GENERAL 1.1 APPLICABLE PUBLICATIONS: The publications listed below form a part of this specification to
Custom-made windows and doors designed for you and your home. vistawindowreplacements.com
vistawindowreplacements.com Custom-made windows and doors designed for you and your home With Vista Windows, you can be sure that the beauty of your windows last you a lifetime! Our Family of Windows The
THE ULTIMATE HIGH PERFORMANCE REPLACEMENT WINDOWS AND PATIO DOORS
THE ULTIMATE HIGH PERFORMANCE REPLACEMENT WINDOWS AND PATIO DOORS EXCLUSIVELY BY NORANDEX Peace of mind? It starts here. Norandex is known throughout the home improvement industry for integrity and commitment
170 Sliding Patio Door available Styles
170 Sliding Patio Door available Styles A-171 OXO Continuous Frame Continuous Frame Transom Sidelite A-172 XO OX A-173 XOO OOX A-175 OXXO Manufacturer of Alpine Window Products 170 Sliding Patio Door Component
Open Up Your Space, Add Light Series 2050 and Series 2050i Garden Windows
Open Up Your Space, Add Light Series 2050 and Series 2050i Garden Windows Series 2050 Garden Window The Series 2050 standard garden window has an outstanding reputation for its distinctive design and excellent
T H E A A M A C E R T I F I C A T I O N P R O G R A M
T H E A A M A C E R T I F I C A T I O N P R O G R A M AAMA STANDS FOR QUALITY Since 1962, AAMA Certification, the original third-party window performance program, has provided manufacturers with the means
Enjoy the view. THE AMCRAFT GRAND ESTATES VINYL WINDOW AND PATIO DOOR COLLECTION
Enjoy the view. THE AMCRAFT GRAND ESTATES VINYL WINDOW AND PATIO DOOR COLLECTION Grand Estates Windows & Doors Home building and remodeling is what you make it and Amcraft makes it easy. For over two decades
Milgard Style Line Series Vinyl Window 3-Part Specification
Milgard Style Line Series Vinyl Window 3-Part Specification GENERAL NOTES TO SPECIFIER: THIS SPECIFICATION SECTION HAS BEEN PREPARED TO ASSIST DESIGN PROFESSIONALS IN THE PREPARATION OF PROJECT OR OFFICE
DE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden window unit.
Important Information for New Construction Installations Attention Installer! We urge you to read and follow the attached installation instructions. Failure to do so may void the warranty of this garden
AST M F 1642-04/GSA TS01 T EST R EPO R T. Rendered to: UNI T E D ST A T ES A L U M INU M
AST M F 1642-04/GSA TS01 T EST R EPO R T Rendered to: UNI T E D ST A T ES A L U M INU M SE RI ES/M O D E L : B W3250 PR O DU C T T YPE : Aluminum Combination Fixed Window Summary of Results Title Test