AAMA/WDMA/CSA 101/I.S.2/A TEST REPORT. Rendered to: EAGLE WINDOW & DOOR COMPANY

Transcription

1 Architectural Testing AAMA/WDMA/CSA 101/I.S.2/A TEST REPORT Rendered to: EAGLE WINDOW & DOOR COMPANY SERIES/MODEL: Series 01 Axiom Clad One-Piece Casement Fixed 6060 PRODUCT TYPE: Aluminum Clad Fixed Wood Window Title Summary of Results Primary Product Designator FW-C x 1829 (72 x 72) Design Pressure 3840 Pa (80.0 psf) Air Infiltration <0.05 L/s/m 2 (<0.01 cfm/ft 2 ) Water Penetration Resistance Test Pressure 580 Pa (12.0 psf) Uniform Load Structural Test Pressure Pa ( psf) Forced Entry Resistance Grade 40 Test Completion Date: 09/13/07 Reference must be made to Report No , dated 05/02/08 for complete test specimen description and data. 849 Western Avenue North St. Paul, MN phone: fax:

2 Architectural Testing AAMA/WDMA/CSA 101/I.S.2/A TEST REPORT Rendered to: EAGLE WINDOW & DOOR, INC Kerper Boulevard Dubuque, Iowa Report No.: Test Dates: 08/06/07 Through: 09/13/07 Report Date: 09/27/07 Report Revision Date: 05/02/08 Expiration Date: 08/06/11 Project Summary: Architectural Testing, Inc. was contracted by Eagle Window & Door to perform testing on Series 01 Axiom Clad One-Piece Casement Fixed 6060, Aluminum Clad Fixed Wood window. The sample tested successfully met the performance requirements for a FW-C x 1829 (72 x 72) rating. Test specimen description and results are reported herein. The sample was provided by the client. Test Specification: The test specimen was evaluated in accordance with AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard/Specification for Windows, Doors, and Unit Skylights. Test Specimen Description: Series/Model: Series 01 Axiom Clad One-Piece Casement Fixed 6060 Type: Aluminum Clad Fixed Wood Window Overall Size: 1829 mm (72") wide by 1829 mm (72") high Sash Size: 1791 mm (70-1/2") wide by 1791 mm (70-1/2") high Area: 3.3 m² (36.0 ft²) Finish: Exterior cladding was painted; interior wood was natural. 849 Western Avenue North St. Paul, MN phone: fax:

3 Test Specimen Description: (Continued) Architectural Testing Page 2 of 5 Revision Date: 05/02/08 Frame Construction: The wood frame was comprised of laminated veneer lumber with corners square cut, butted, sealed with silicone and secured with two 11 mm (7/16") by 38 mm (1-1/2") staples and 38 mm (1-1/2") by 25 mm (1") corrugated fastener per corner. Extruded aluminum cladding was slip-fit over the wood frame members with the corners miter-cut, sealed with silicone and secured with a nylon corner key, two #6 by 11 mm (7/16") screws per corner and one #10 by 64 mm (2-1/2") screw per corner. Sash Construction: The wood sash utilized lap-joint construction and was fastened with glue and one 5 mm (3/16") by 29 mm (1-1/8") staple per corner. The sash assembly was set into the frame assembly and held in place by wood frame stops secured with 5 mm (3/16") by 29 mm (1-1/8") staples located 25 mm (1") from each corner and 152 mm (6") to 203 mm (8") on center. Glazing Details: The window utilized a nominal 19 mm (3/4") thick insulating glass unit fabricated from two 6 mm (1/4") sheets of annealed glass separated by a desiccant-filled aluminum box spacer system. The glass was set from the interior against butyl tape and back-bedded with silicone. Wood glazing stops with single-sided adhesive foam tape were utilized on the interior and secured with 32 mm (1-1/4") brad nails spaced 25 mm (1") from each corner and 152 mm (6") to 203 mm (8") on center. Installation: The window was installed within a wood test buck. The window was anchored to the buck with installation straps that were secured to the window frame with two #8 by 16 mm (5/8") wood screws and to the buck on the interior with two #8 by 38 mm (1-1/2") screws. The installation straps were additionally secured on the exterior through the flange then through the installation strap with two #8 by 38 mm (1-1/2") screws. The installation straps were located 152 mm (6") from each corner and midspan on each side. The nail flange was additionally secured with 51 mm (2") roof nails spaced 51 mm (2") from each corner and 203 mm (8") on center Silicone sealant was used to seal the window to the test buck. Test Results: The temperature during testing was 26 C (78 F). The results are tabulated as follows: Paragraph Title of Test - Test Method Results Allowed Air Leakage Resistance per ASTM E Pa (1.6 psf) <0.05 L/s/m L/s/m 2 (<0.01 cfm/ft 2 ) (0.3 cfm/ft 2 ) max. 300 Pa (6.2 psf) <0.05 L/s/m 2 -- (<0.01 cfm/ft 2 ) -- Note #1: The tested specimen meets (or exceeds) the performance levels specified in AAMA/WDMA/CSA 101/I.S.2/A for air leakage resistance.

4 Architectural Testing Page 3 of 5 Revision Date: 05/02/08 Test Results: (Continued) Paragraph Title of Test - Test Method Results Allowed Water Penetration Resistance per ASTM E 547 and E 331 See Note # Uniform Load Deflection per ASTM E 330 See Note # Uniform Load Structural per ASTM E 330 See Note #2 Note #2: The client opted to start at a pressure higher than the minimum required. Those results are listed under "Optional Performance" Forced Entry Resistance per ASTM F 588 Type: D Grade: 10 Optional Performance Disassembly Test No entry No entry Sash/Panel Manipulation Test No entry No entry Lock Hardware Manipulation Test No entry No entry Water Penetration Resistance per ASTM E 547 and E Pa (12.0 psf) No leakage No leakage Uniform Load Deflection per ASTM E 330 (Deflections were taken on the frame) (Loads were held for 60 seconds) 3840 Pa (80.0 psf) (positive) 0.76 mm (0.03") See Note # Pa (80.0 psf) (negative) 1.02 mm (0.04") See Note #2 Note #3: The deflections reported are not limited by AAMA/WDMA/CSA 101/I.S.2/A for this product designation. The deflection data is recorded in this report for special code compliance and information only Uniform Load Structural per ASTM E 330 (Permanent sets were taken on the frame) (Loads were held for 10 seconds) 5760 Pa (120.0 psf) (positive) <0.25 mm (<001") 3.05 mm (0.12") max Pa (120.0 psf) (negative) 0.76 mm (0.03") 3.05 mm (0.12") max. Tape and film were used to seal against air leakage during structural testing. In our opinion, the tape and film did not influence the results of the test. Drawing Reference: The test specimen drawings have been reviewed by Architectural Testing, Inc. and are representative of the test specimen reported herein.

5 Architectural Testing Page 4 of 5 Revision Date: 05/02/08 List of Official Observers: Name Chad Cornell Mike Blum Anthony D. Gavin Karl A. Lips-Eakins Eric J. Schoenthaler Company Eagle Window & Door, Inc. Eagle Window & Door, Inc. Architectural Testing, Inc. Architectural Testing, Inc. Architectural Testing, Inc. Detailed drawings, data sheets, representative samples of test specimens, a copy of this report, or other pertinent project documentation will be retained by Architectural Testing, Inc. for a period of four years from the original test date. At the end of this retention period, such materials shall be discarded without notice and the service life of this report will expire. Results obtained are tested values and were secured by using the designated test methods. No conclusions of any kind regarding the adequacy or inadequacy of the glass in the test specimen can be made. This report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the specimens tested. This report may not be reproduced, except in full, without the written approval of Architectural Testing, Inc. For ARCHITECTURAL TESTING, INC. Eric J. Schoenthaler Project Manager Daniel A. Johnson Director - Regional Operations EJE:mb Attachments (pages): This report is complete only when all attachments listed are included. Appendix-A: Alteration Addendum (1) Appendix-B: WDMA Submittal forms (2) Appendix-C: Drawings (12)

6 Architectural Testing Page 5 of 5 Revision Date: 05/02/08 Revision Log Rev. # Date Page(s) Revision(s) 0 09/27/07 N/A Original report issue. Report and drawings forwarded to AMS for Hallmark Certification 1 05/02/08 Cover Correction made to Series/Model. Report and drawings forwarded to AMS for Hallmark Certification This report produced from controlled document template ATI 00159, revised 06/18/07.

7 Architectural Testing Note: No alterations were required. Appendix A Alteration Addendum

8 Architectural Testing Appendix B WDMA Submittal Forms

9 WDMA HALLMARK CERTIFICATION PROGRAM REPORT SUBMISSION FORM THIS FORM IS TO BE COMPLETED BY THE MANUFACTURER AND SUBMITTED TO AMS PRIOR TO OR ALONG WITH SUBMISSION OF EACH NEW OR REVISED TEST REPORT FOR CERTIFICATION TO THE HALLMARK PROGRAM. ANY QUESTIONS PLEASE CONTACT AMS AT OR Manufacturer: Eagle Window and Door Contact: Todd Bergstrom Plant Location(s): Phone: (list all plants where product is made) 2045 Kerper Blvd, Dubuque IA Test Report #: Product Relationship: Extension of currently certified product? yes X no n/a Recertification X New (check one) If yes, what CCL #? 099-H-624 Difference from Certified Product: RE-CERTIFY UNDER PREVIOUSLY USED CCL NUMBER Is this a Gateway Test? yes X no n/a Does this report require a Gateway Report #? yes no n/a Report #: Impact Report: If this is not an impact report check here: AWS Report # X Test Plan #? yes no n/a Installation Instructions submitted? yes no n/a Certification to Florida: If this will not be submitted to Florida check here: AMS to Input to Database yes no n/a Manufacturer to input X yes no n/a WD-08 01/11/07

10 WDMA HALLMARK CERTIFICATION PROGRAM REPORT SUBMISSION FORM Product Name: Series 00 Axiom Clad 1PC Casement Fixed 6060 (as to be listed on CCL) Product Type: Casement Window Additional Manufacturer ID #: X n/a Hallmark CCL Standard Rating ANSI/AAMA/NWWDA 101/I.S /I.S.2/NAFS-02 X AAMA/WDMA/CSA/101/I.S.2/A FW-C80 (1829x1829) ASTM E / E ASTM E / E ASTM E / E ASTM E / E ASTM E / E ASTM E / E ASTM E ANSI A TAS TAS TAS Other: WD-08 01/11/07

11 Architectural Testing Appendix C Drawings

12

13

14

15

16

17

18

19

20

21

22

23