Installation Instructions

Size: px

Start display at page:

Download "Installation Instructions"

Kory Walton
7 years ago
Views:

1 Installation Instructions HT5000 Series Electric Strike Product Components 1 1 HT5000 Electric Strike Body 2 Trim Enhancer (with screws) 1 2 ELECTRICAL RATINGS Average Amp: 0.25 Average Amp: to +24 (+/-10%) Volts DC Seated Unseated MINIMUM WIRE GAUGE REQUIREMENTS 200 feet or less feet feet Solenoid Voltage 24 VDC 20 gauge 18 gauge 16 gauge FIVE YEAR LIMITED WARRANTY For any questions regarding this information, call HES Customer Support at N. 17th Ave. Phoenix, AZ For UL Listed applications, the unit shall be connected to a UL Listed Class 2 power supply or a UL 294 Listed control unit. 12 VDC 18 gauge 16 gauge 14 gauge ASSA ABLOY, the global leader in door opening solutions

2 2 Hi-O Overview ASSA ABLOY s standard-based Hi-O system Highly Intelligent Opening connects electronic (Controller Area Network) data network, allowing them to communicate and monitor the health of the opening. Intelligence is built into each device instead of one centralized logic unit, creating a plug-and-play system. Each device is instantly recognized when plugged into the system similar to what happens when a USB device is plugged into a computer. Every unit is connected with a four-wire cable and has ElectroLynx plug-in connectors for quick installation. Hi-O is based on devices with built-in intelligence and a CANbus that links all the devices together. Data traffic on the Hi-O CANbus can be encrypted. Each Hi-O device (such as a push plate, electric strike, card reader, door operator, etc.) is connected to the CANbus through a single, four-wire cable. Two of the wires supply power and the other two are used for data communication. Refer to the Hi-O Systems Manual (A8002). Prepare Strike 1. Evaluate opening and reset Dip Switch if needed (see page 4 (ADJUSTMENT INSTRUCTIONS). 2. For available faceplate options, see page 8. Prepare Frame 1. Prepare frame using the appropriate template for your lockset and faceplate combination (see page 3-4). 2. Connect to system using electrolynx connectors (see Page 3). Diagram A 3. Install the HT5000 strike body into the door frame. 4. Set up the Hi-O system (see pages 5-7.

3 3 Prepare Strike Wiring The HT5000 series drawing below show the -Hi O application. Voltage: 12-24VDC (11-28VDC range) operation Filtered and Regulated Power Supply Current:.5 Amp Seated.04 Amp Unseated A. Electrolynx Connectors PIN 2 Red ( VDC) PIN 4 PIN 6 PIN 8 PIN 7 Brown (CANbus ) PIN 5 PIN 3 White (CANbus ) PIN 1 Black (0 VDC) NOTE: For HT5000 (On the 8-Pin Connector): PIN 2 Red (Power VDC) PIN 1 Black [Power 0 VDC/Common(-)] PIN 3 White CAN bus HIGH PIN 7 Brown CAN bus LOW B. Electrolynx Connector System Notes The System is designed to be installation friendly with quick connectors. The total length of the bus should not be more then 50 meters (164 feet) and stub (star) connections should not be more then 10 meters (33 feet). The optimal solution places the door controller close to the door to keep cable lengths to a minimum. IMPORTANT: ElectroLynx connectors plug and lock together in only one way, as shown. Do NOT force connectors together.

4 4 Adjustment Instructions The default factory settings will be used in almost every application. They are: Group 1 Terminator OFF NOTE: If necessary, follow the procedure below to change the DIP switch settings before installing strike. IMPORTANT: Ensure that the serial number of the unit is retained. Once the device is locked and encryption enabled, access to the device requires the serial number. If the serial number is lost, the device must be returned to the factory to be reset. A. To change the settings, remove the label from the back of the strike. DO NOT DAMAGE LABEL. This label will be re-applied after DIP switch setting is complete. After label is removed, carefully use a small screwdriver to set DIP switch (see instructions 2 and 3). When setting is complete, re-apply the serial label to the back of the strike. B. SWITCH 1: Set the manual group switch. Default is OFF and is appropriate for most applications. Most installations use Group 1 only. Switch 1 OFF = membership in Group 1. Switch 1 ON = membership in Group 2. B. SWITCH 2: Set the termination resistor (Default is OFF). In a Hi-O CANbus network, it is necessary to terminate the communication bus to avoid interference. Termination should take place in Activators, for example in a card reader, opening button, or a gateway. Switch 2 OFF removes the 120 ohm connection between CAN-Low and CAN-High. Switch 2 ON terminates a 120 ohm resistor between CAN-Low and CAN-High. Use only one termination resistor per application. Refer to the Hi-O Systems Manual (A8002) for additional information. Switch position default settings ON 1 2

5 5 Hi-O System Software Step 3 Step 4 Step 5 Step 6 Step 1: Install hardware according to installation instructions and the Hi-O System Manual. Step 2: Download and install the latest release of Hi-O Manager and Logger software, and DDF files according to the Hi-O System Manual. Step 3: Open Hi-O Manager and click the Next button to determine what devices are attached to the system. Step 4: Icons representing system appear in the left pane. Step 5: Click the Push Button icon. Step 6: In the Properties tab of the right pane, click the Advanced Properties arrow to view the Properties pane. Step 7: In the Property Group pane, set security locking and timers, and set the values that will generate system messages. In the Property Group menu, select from the following: Information Read-only information from the device. Device Offline Behavior Set unlock, delay and egress timing for Lock. Voltage Out of Range Limits Set low and high thresholds for voltage. When thresholds are exceeded system messages will be generated. Jam Timers Set time to dictate when a jam message is sent when the strike is locked and keeper open. Transmit Command Validation Set the above Locking, Security Locking, Opening, Holding, Activator State, and System Voltage to valid or invalid. Refer to the Hi-O System Manual (A8002) for additional information.

6 6 Hi-O Systems Settings Select the Properties tab. Click the Push Button icon in the view pane. Click the Advance Properties arrow to expand the menu. Choose from the Properties Groups list: Information Device Offline Behavior Voltage Out of Range Limits Jam Timers Transmit Command Validation Information Displays read-only general information from the device, including: Serial Number Node ID Host Node ID Product Class Application Name (Model Number) Hardware Version Hi-O Stack Version Hardware Group ACP Active (Address Claiming Process)

7 7 Hi-O System Settings Device Offline Behavior Device Offline Behavior No Change Lock Unlock Voltage Out of Range Limits Jam Timers Transmit Command Validation Set Voltage Out of Range Limits Establishes Out of Range entries in Log. Low Overflow Voltage in Volts High Overflow Voltage in Volts 11 to 28 is the normal range. Set Jam Timers Set time to dictate when a jam message is sent when the strike is locked and keeper open. Jam Delay Timer in seconds (0 255) Set Transmit Command Validation Sets Locking, Security Locking, Opening, Holding, Activator State, and System Voltage entries to valid or invalid, determining if the entries are read or ignored. NOTE: If it is not possible to set respective entries, check to see if they are set to valid. Refer to the Hi-O System Manual (A8002) for additional information

8 Cutout Templates WITH SCHLAGE AND YALE MORTISE LOCKS HT5000 WITH 501 FACE PLATE HT5000 WITH 501A FACE PLATE Inches [mm] 1 1/4" [31.8] 1 1/4" [31.8] 4 7/8" [124] 4 7/8" [124] 3/32" [2.3] 3/32" [2.3] HT5000 WITH 501B FACE PLATE HT5000 WITH 502 FACE PLATE 1 7/16" [36.5] 4 7/8" [124] 7 15/16" [201.6] 1 1/4" [31.8] 3/32" [2.3]

9 Cutout Templates WITH SCHLAGE AND YALE MORTISE LOCKS HT5000 WITH 503 FACE PLATE HT5000 WITH 503B FACE PLATE Inches [mm] 1 7/16" [36.5] 6 7/8" [174.3] 6 7/8" [174.3] 3/32" [2.3] 1 1/4" [31.8] HT5000 WITH 504 FACE PLATE 1 3/8" [34.9] 10" [254] 1 1/2" [38.1] 3/32" [2.3]

10 HT5000 ELECTRIC STRIKE INSTALLATION INSTRUCTIONS rev A 2008 HES Inc.

Allegion AD-300 Installation Application Note. 1.0 Hardware Requirements. 2.0 Software/Licensing Requirements

Allegion AD-300 Installation Application Note. 1.0 Hardware Requirements. 2.0 Software/Licensing Requirements Allegion Schlage AD-300 networked, hardwired locks can be integrated seamlessly with the Doors.NET software when used with the NXT-MSC (Mercury-Powered controllers). You can connect and communicate with