Villa Toscana Return Desk

Transcription

1 Villa Toscana Return Desk ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES If you have any questions regarding assembly or if you are missing parts, do not return this item to Costco Wholesale Club Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: Pacific Standard Time: 8:30 am - 4:30 pm Monday to Friday Page # 1

2 Parts List Please read the instructions and verify that all parts listed on the parts list are complete before beginning assembly. A- Desk Top (1) B- Return Top (1) C- Drawer Pedestal (1) D- Computer Pedestal (1) E- Desk Back Panel (1) F-Pencil Box (1) G- Desk Side Panel (1) H- Desk Drawer Box (1) I- Return Keyboard Box (1) Page # 2

3 Parts List Please read the instructions and verify that all parts listed on the parts list are complete before beginning assembly. J- Return Back Panel (1) K-Curved Middle Panel (1) L- Inner Box (1) M- Shelf (1) Touch Up Pen (1) (Inside Computer Pedestal) 1-2 1/4 Bolt 2-1 1/4' Bolt 3-Flat Washer (2) (23+1 extra) (25+1 extra) 4-Wood Dowel for Inner Box (2) 5- Shelf Pin 6-5/8 Screw (Pre-attach) (4+1 extra) (21+1 extra) 7-1 Screw (3) 8-Grommet (3) 9- Figure 8 (pre-attach) Tools required: Phillips Screwdriver. Page # 3

4 How to adjust the European adjustable hinges on doors Shipping may cause doors to become out of alignment. If you find that the doors need to be adjusted slightly turn the appropriate screw as illustrated. 1. TO ADJUST DOOR FORWARD OR BACKWARD. 2. TO ADJUST DOOR TO RIGHT OR TO LEFT. 3. TO ADJUST DOOR UP OR DOWN. Page # 4

5 If you remove the Drawers or Pull-outs with ball bearing slides from the unit, please follow the below steps to prevent any damage to the slides or the drawers. 1. If you remove the Drawer please pull the drawer all the way out, then push the plastic tab of the ball bearing slide up on one side and down in the other side, and then pull the drawer completely out. See detail #A. 2. To place the drawer back just simply push the ball bearing cart all the way to the end of the slide (in both sides), and align the slides on the drawer with the slides on the unit and push it carefully inside until stop. See detail #B. Note: If they do not go smoothly please take out and repeat step. Page # 5

6 Assembly Instructions 1. Unpack the unit and confirm that you have all hardware and parts required. 2. Attach the Desk Back Panel (part E) to the Drawer Pedestal (part C) using three 1 1/4" Bolts (part 2) through the Flat Washers (part 3) through the cleat into the threaded inserts of Drawer Pedestal. See detail #1. 3. Proceed to attach the Desk Side Panel (part G) into Desk Back Panel (part E) with the 1 1/4" Bolts (part 2) and Washers (part 3). See detail #1. 4. Insert Desk Drawer Box (part H) into place, between the Drawer Pedestal (part C) and Desk Side Panel (part G) using the 1 1/4" Bolts and Flat Washers (to be able to insert the bolts you will need to remove the drawer from the box, please don t put back until you finish your assembly). As shown in detail #1. 5. Bolt the Computer Pedestal (part D) and Return Back Panel (part J) with three 1 1/4" Bolts and Flat Washers (part 2 & 3). Now proceed to assemble the Curved Middle Panel (part K) into the Return Back Panel (part J) with the 1 1/4" Bolts and Flat Washers through the cleat of the Return Back Panel. As shown in detail #2. 6. Pick up the Return Drawer Box (part I) and remove pullout. Attach the Return Drawer Box into Computer Pedestal (part D) and Curved Middle Panel (part K) using the 1 1/4" Bolts and Flat Washers (part 2 & 3) from inner side. As shown in detail #2. Page # 6

7 7. Attach the Desk to the Return with two 2 1/4 Bolts (part 1) and Flat Washers (part 3). Insert the Bolts and Flat Washers from inside the Desk Drawer Box (part H) through the Curved Middle Panel (part K). See detail #3. 8. Finish attach you need insert three 1 1/4" Bolts and Flat Washers (part 2 & 3) through the cleat of the Desk Side Panel (part G) into the threaded insert of the Curved Middle Panel (part K), as shown in detail #3. Page # 7

8 Assembly Instructions 9. Before placing the Tops in place make sure that part of the figure 8 (metal piece you see attached on top ends of the panels) is facing out, you only need to turn the hardware out this will enable you to attach the tops to the assembly. Now put both tops in place (use the dowels on top of the panels as guides) and screw from underneath by using the 5/8" Wood Screws (part 6) through the figure 8 (part 9) to attach the Tops. When attach the Return Top (part B) you need insert and screw three 1 Screws (part 7) through the pre-drilled holes included on the front rail of the Return Drawer Box into the Top. See detail # Place the Grommets (part 8) over the top holes of the Desk and Return Top (part A & B). 11. Finish your assembly by inserting both the Return Keyboard Box and Desk Drawer Box into place. Note: You can place the Pencil Box (part F) into the Desk Center Drawer and Keyboard Pull-out. 12. When you open the Keyboard Pull-out you can flip down the keyboard front by pushing down the Rooster Catch on the keyboard front hardware on both ends, as shown in detail #5. Page # 8

9 Assembly Instructions Your desk is designed to accommodate most computer configurations and can be used with Tower, Mini-Tower computers. For Mini-tower CPU configuration: Insert the Shelf Pins (part 5) into the holes of the Inner Box (part L) and side of the Computer Pedestal (part D). Now install the Shelf (part M) if space available. See detail #5. For Tower CPU configuration: Remove the Shelf (part M). A Touch Up Pen has been provided to repair any small nicks or scratches that may occur during assembly or shipping. Keep these instructions for further use Your assembly should now be complete. Thank you for your purchase! Page # 9