Nelson "Options" 60W Polycarbonate Lantern

Transcription

1 Nelson "Options" 60W Polycarbonate Lantern BQ-SNL-PL02-60-B INSTALLER GUIDE V1.0-12/06 E-488B IQ Europe Limited Sandbeck Lane, Wetherby LS22 7TW. Visit us at Installation helpline

2 MANUFACTURER'S EXTENDED WARRANTY In addition to your statutory rights relating to this product it is also guaranteed by IQ (Europe) Limited ("IQ") for 12 months from the date of purchase against faulty materials or workmanship which affect its designed ability to detect or switch. During this period if the product has a defect of this nature it will be repaired or replaced free of charge by IQ with the same item, or a similar one of higher specification, ON CONDITION THAT:- The buyer takes advantage of any 'return to store' scheme operated by the seller from whom it is bought. If the product has a defect outside the period of any seller's 'return to store' scheme it should be returned to IQ (Europe) Limited at Sandbeck Lane, Wetherby, W. Yorks LS22 7TW, England at the expense of the buyer together with evidence of the date of purchase (it is the responsibility of the buyer to prove delivery to IQ). The product has been bought by the user. The product has not been misused or handled carelessly, installed incorrectly, or used on a voltage supply other than that shown on it. Repairs have not been attempted by anyone other than IQ's staff. The product has been used for domestic purposes only. The product has not been installed in any unusually exposed or harsh environmental conditions. If the buyer is resident in the EU the product or its replacement will be returned to the buyer at the expense of IQ. This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable parts and in particular lamps, glass panels, or globes/lanterns. It does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. This contract is subject to the laws of England and Wales. *** IMPORTANT *** As of 1 January 2005, changes to the Building Regulations affect domestic electrical installations in England and Wales. You don't need to be a qualified electrician to make changes to your home's electrical system, but the work must be done in accordance with the Regulations. Where you employ an electrician who is a member of a competent person self-certification scheme, they will be able to certify the work complies with the Regulations. If you decide to carry out the work yourself we recommend that you make yourself aware of the Regulations before you begin and if you require any clarification you should contact your Local Authority Building Control Department. Details of the Building Regulations can be obtained on the internet via the government website gov.uk/explanatory-booklet

3 SECTION ONE GENERAL INFORMATION Thank you for buying this IQ OPTIONS light fitting and we hope you will be fully satisfied with your choice. For your own safety you should read this leaflet before using your unit as it offers advice and precautions for installation and use. The OPTIONS range of light fittings are attractive and useful products in their own right but in addition they also offer you something more than your average light fitting. Each and every OPTIONS light fitting is manufactured with the capability to accept the OPTIONS Sensor Module; sold separately. Installation of this Sensor Module converts the light fitting from a manual into an automatic unit with three different control OPTIONS for you to select from. Without the OPTIONS Sensor module fitted you will need to manually turn your light fitting on and off as and when you need it. With the OPTIONS Sensor Module fitted you can forget about having to remember to switch the unit on or off as the sensor module will do this for you. The OPTIONS Sensor Module can be fitted at any time, before during or after the installation of your OPTIONS light fitting. It takes just a couple of minutes to fit, all you need to do is remove the cap and slide the Sensor Module into place, once inserted it will lock in position. Your next step is to choose from the three different operating control modes available on the Sensor Module. Once the OPTIONS Sensor Module has been installed you can choose from the following Night Sensor; the unit will illuminate at a level of darkness set by you, and will remain illuminated throughout the night, switching itself off at dawn. This mode is ideal for use with low energy lamps but check your OPTIONS Light Fitting to see if Low Energy lamps are capable of being installed. Motion Sensor Mode; the unit will begin to operate at a level of darkness set by you, illuminating only when the sensor detects movement. The unit will then remain illuminated for a period set by you, returning to the off position when activity ceases. This mode is ideal if you just want light when its needed. Night & Motion Sensor Mode; the unit will operate as per the Motion Sensor mode except that at dusk the unit will illuminate to a dimmed level set by you (0-50%), switching to full brightness when motion is detected, returning to the dimmed level when activity ceases and switching off completely at dawn. This mode is ideal if you want a little bit of light to enhance the night time appearance of your home but with more light being automatically available when movement is detected. Your selection of an OPTIONS light fitting was a good choice in its own right, but it can be a great choice if you combine it with the OPTIONS Sensor Module. OPTIONS the range of lighting products that provide you with more choice and more control OPTIONS Allows you to mix and match manual and automatic units, and to switch between any one of three differing control modes depending on location or preference. Remember you can install an OPTIONS Sensor Module at any time, so the next time you visit your local OPTIONS retailer why not convert to automatic.

4 PARTS INCLUDED - Luminaire - Instruction manual. Please keep safe for future reference. - Wall fixing screws and wall plugs - Blanking Plate - Wall Plate TOOLS & PARTS NEEDED - Electric/hand-held drill & bits. - Terminal or Electricians screwdriver - Large slotted/philips screwdriver - Wire cutters - 1.0mm sq. round flexible cable - 60W Max GLS ES Lamp (refer to Section 5 for further details) This lantern is for outdoor use only. Unit must be mounted on a non-flammable surface as a fixed luminaire, and is not suitable for portable use.the unit can get very hot during use. Ensure the unit has cooled before handling.ensure adequate ventilation space is allowed between the unit and any object above, in front or to either side of the unit. Suggested space is 0.5m above, 0.3m to either side & 1.0m in front. Do not attempt to install during wet weather, if you are suffering from nausea or dizzy spells or on medication with similar side effects If in any doubt, consult a qualified tradesperson or electrician. SECTION TWO SELECTING THE LOCATION If it is your intention to use the OPTIONS control module, for best results mount at height of 1.8m. See OPTIONS module instruction manual for more details. SECTION THREE INSTALLATION *** IMPORTANT *** Switch off the electricity at the fuse box by removing the relevant fuse or switching off the circuit breaker before proceeding with the installation. After choosing a suitable location (see previous section) install the unit as follows: The unit is suitable for connection to a 240V 50Hz electricity supply. It is suggested that 3-core round flexible cable of 1mm² gauge is used. An internal switch should be installed to switch the power to the unit ON & OFF. This allows the lantern to be easily switched off when not required or for maintenance purposes. It is recommended that the lamp is fitted before the lantern is fixed to the wall. Fit the lamp as follows. Release the four hexagonal nuts and washers on the top cover of the lantern see aiagram A and release the top cover. Fit the lamp. Replace the top cover and secure using the four fixing nuts and washers.

5 IMPORTANT! If you intend to benefit from the addition of the OPTIONS module, please refer to the OPTIONS control module instruction manual for advice on assembly and set up. If you intend not to use the OPTIONS module,the blanking plate MUST be fitted to maintain Safety Regulations! Fit Blanking Plate supplied by simply inserting into the aperture shown on diagram B. Ensure blanking plate is fully secured to ensure a watertight seal. There will be an audible click and the cover will fit securely into its circular aperture. If the blanking plate is missing from this product, DO NOT INSTALL, please contact the Consumer Helpline below. The unit is ready for mounting to the wall. The wall bracket is packed seperately, remove from packaging. Based on the location of your incoming cable,use the wall plate as a template and mark the position of the mounting holes. Ensure the wall plate is in the correct orientation by referring to the to arrow marked "TOP" See Diagram C, Drill holes and insert wall plugs into the holes. Pierce and pass the cable through the grommet before securing the wall plate to the wall. Fit the wall plate to the wall Do not overtighten, if using a power screwdriver ensure it is set to the lowest torque setting to prevent damage to the wall plate. CONNECTION It is recommended that the circuit is protected by a 5A max fuse or circuit breaker. It is recommended that this product is connected to fixed wiring only. Connect the cable to the terminal block on the unit as follows (see connection diagram): LIVE (Brown) EARTH (Green/Yellow) NEUTRAL (Blue) L N Ensure that the connections are secure and the terminal block is securely located on its mounting posts. CONNECTION DIAGRAM Mains Supply L E N Isolation Switch L E N

6 This product uses a fast fix connector and it is imperative the connector is aligned when assembling the lantern onto the wall plate. This is best achieved by first aligning the top edge of the lantern onto the curved edge at the top of the wall plate, ensure that the holes at the top and bottom of the lantern bracket are aligned with the holes in the wall plate, this will ensure the pin connections of the fast fix connector are aligned with their receptacles, see diagram C. Fully secure the lantern fixing screws See Diagram D. Installation is complete. SECTION FOUR OPERATION AND TESTING Turn on the power to the lantern, the lamp should illuminate. If you have purchased the OPTIONS Module, please refer to the "Operation and Testing" section of the OPTIONS module manual. If you have any problems, please refer to the troubleshooting guide and Technical Helpine details below. SECTION FIVE TECHNICAL SPECIFICATION Power Supply V AC ~ 50Hz Maximum Switchable Load 60W GLS or Equivalent CFL ES Energy Saving lamp. IMPORTANT! If using the XXX Module, please refer to its instruction manual for important information when using Energy Saving Lamps Environmental Protection IP44 Suitable for outdoor use If you experience problems refer to Troubleshooting Guide. If problems still exist, do not immediately return the unit to store. Telephone the IQ Customer Helpline Weekdays 9.00am pm support@iq-group.com Qualified Customer Support Co-ordinators will be on-line to assist in resolving your query. SECTION SIX TROUBLESHOOTING GUIDE PROBLEM SOLUTION Lantern did not operate at all. Check that the power is switched ON at the circuit breaker/ internal wall switch. Turn OFF the power to the unit and check the wiring connections as per the diagram (see previous section 3). Ensure no connections are loose. Check the lamp. If the lamp has failed, replace. Ensure that the lamp is seated correctly in the lampholder. IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN. IF OPTIONS MODULE IS USED PLEASE REFER TO THE TROUBLESHOOTING GUIDE IN THE OPTIONS MODULE MANUAL.

7 cover fixing hexagaonal nuts and flat washers x 4 A B blanking plate wall fixing hole C D Align lantern lid with top edge shown fast fix connector lantern fixing screw x 2 cable inlet wall fixing hole

8 Please see Selecting a Location for information on choos-?did YOU KNOW... ing the optimum location for your lantern IQ products are designed and manufactured to give many years of trouble-free service. The materials used during manufacture have been selected to improve their ability to be recycled when the product is no longer functional. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice SAVE MONEY & HELP THE ENVIRONMENT Consider using smaller wattage lamp. This could save you up to 40% in running costs, whilst also conserving precious natural resources. LIGHT POLLUTION & CONSIDERATE LIGHTING Please be aware of the annoyance over-lighting an area can cause to your immediate neighbours. Light pollution caused by incorrectly installing a lantern or over-lighting an area can be limited by carefully considering the location and position of your lantern before installation. Please try to concentrate the light on your property and limit the potential inconvenience of the light shining into your neighbours windows etc.