Tile Adhesives KALEKIM KALEKİMBEYAZ TECHNOFLEX GRANİTECH PROFESYONEL TECHNOBLOCK TECHNOMAX 30 RAPİTECH TECHNOPOOL TECHNOFULL TECHNOLIGHT
|
|
- Gervase Harrison
- 7 years ago
- Views:
Transcription
1 Kalekim Tile Adhesives 17 Tile Adhesives KALEKIM KALEKİMBEYAZ TECHNOFLEX GRANİTECH PROFESYONEL TECHNOBLOCK TECHNOMAX 30 RAPİTECH TECHNOPOOL TECHNOFULL TECHNOLIGHT KALEKİMTOZUMAZ SUPERTECH TECHNOPUR
2 18 Kalekim Tile Adhesives 1051 KALEKİM Tile Adhesive Cementitious ceramic tile adhesive with extended open time and reduced slip. Floor and wall bonding of all types of ceramic tiles, mosaic and decorative bricks on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles. High adhesion strength. Allows installation of tiles from top towards the bottom. Extended open time. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Wipe the back side of tiles with water if dusty. Pour 25 kg of KALEKİM into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of KALEKİM with the flat side of trowel, then notch with the toothed side of trowel. Open time is 30 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with KALEKİM must not be subject to water for at least 24 hours. 5 kg polyethylene bag 25 kg multi-ply paper bags. Technical Temperature Range Grey powder place lt water / 25 kg powder lt water / 5 kg powder C1TE TS EN 12004, Class C1TE 1: Normal setting T: Reduced slip E: Extended open time -initial Approx. 6 hours 0.5mm After 30 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m²
3 Kalekim Tile Adhesives KALEKİMBEYAZ White Tile Adhesive White cementitious ceramic tile adhesive with extended open time and reduced slip. Floor and wall bonding of all types of ceramic tiles, mosaic and decorative bricks on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles. Exterior bonding and grouting of glass mosaics. Interior and exterior bonding of glass bricks. Perfect adherence. Allows installation of tiles from top towards the bottom. Extended open time. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Wipe the back side of tiles with water if dusty. Pour 25 kg of KALEKİMBEYAZ into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application. Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of KALEKİMBEYAZ with the flat side of trowel, then notch with the toothed side of trowel. Open time is 30 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with KALEKİMBEYAZ must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags. C1TE TS EN 12004, Class C1TE 1: Standard T: Reduced slip E: Extended open time Technical Temperature Range -initial White powder place litres water / 25 kg powder Approx. 6 hours 0.5 mm. After 30 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m²
4 20 Kalekim Tile Adhesives 1054 TECHNOFLEX Deformable Tile Adhesive High performance cementitious flexible adhesive with extended open time and reduced slip for ceramic tiles and stones. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tile, granite. Bonding of tiles on painted walls and gypsum. Bonding of ceramic tiles in swimming pools, basins and any other wet places. Bonding of tiles on terraces and balconies. Bonding of tiles on places where sudden temperature changes occurs like cold storage depots and over floor heat installations. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Perfect adherence. Highly Deformable, resistant to temperature changes. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. Extended open time. C2TE S1 TS EN 12004, Class C2TE, S1 T: Reduced slip E: Extended Open Time S1: Deformable Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYP- SASTAR on anhydrite screeds. Wipe the back side of tiles with water if dusty. Pour 25 kg of TECHNOFLEX into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOFLEX with the flat side of trowel, then notch with the toothed side of trowel. s of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, TECHNOFLEX should be applied also on the back of tiles. (combined method) Technical Temperature Range -initial (after 28 days) Deformability (EN 12002) Open time is 30 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with TECHNOFLEX must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags. Grey or White powder 12 months when stored in the original sealed packing in dry place litres water / 25 kg powder Approx. 6 hours 0.5 mm. After 30 minutes 8 hours on wall; 24 hours after on floor 3-5kg./m² 2.5 mm-s1 Deformable
5 Kalekim Tile Adhesives GRANİTECH Granite Tile Adhesive High performance cementitious adhesive with reduced slip. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, granite, porcelain ceramic, cotto, clinker on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles or marble. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Perfect adherence. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. Wipe the back side of tiles with water if dusty. Pour 25 kg of GRANİTECH into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of GRANİTECH with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, GRANİTECH should be applied also on the back of tiles. (combined method) Open time is 20 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with GRANİTECH must not be subject to water for at least 24 hours. Since contains cement, irritating to eyes, respiratory system and skin. For further information refer to 25 kg multi-ply paper bags. TS EN 12004, Class C2T T: Reduced slip Technical Temperature Range -initial (after 28 days) Grey or White powder place litres water / 25 kg powder Approx. 6 hours 0.5 mm After 20 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m²
6 22 Kalekim Tile Adhesives 1056 PROFESYONEL Granite Tile Adhesive High performance cementitious adhesive. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, granite, porcelain ceramic, cotto, clinker on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles or marble. Perfect adherence Use TAMİRART or MASTAR 10 in case of any loose and uneven substrates to get a sound and flat surface. Pour 25kg of PROFESYONEL into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of PROFESYONEL with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, PROFESYONEL should be applied also on the back of tiles. (combined method) Open time is 20 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceeded, scratch and discard the mortar. Tiles installed with PROFESYONEL must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags. C2TE TS EN 12004, Class C2 Technical Temperature Range -initial (after 28 days) Grey powder place litres water / 25 kg powder 6 hours 0.5mm After 20 minutes 8 hours on wall; 24 hours after on floor 3-5kg/m²
7 Kalekim Tile Adhesives TECHNOBLOCK Aerated Concrete Adhesive Cementitious masonry mortar for bonding high water absorbing construction elements like aerated concrete. Bonding of aerated concrete and any other high water absorbing construction elements. Perfect adherence Labor-cost effective. Pour 25 kg of TECHNOBLOCK into 8-9 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. (A low speed mixer is recommended to mix). Allow to stand for 5-10 minutes to mature. After remixing, the paste is ready for application. trowel of which notch size is 10x10x10mm. While laying the blocks, vertical and horizontal joints should have maximum 3 mm width and fill them completely with TECHNOBLOCK. Open time is minutes. Lay the blocks within this 7 period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. 25 kg multi-ply paper bags. Data A (cm) B (cm) C (cm) (kg/m 2 ) TS EN Technical Grey powder 12 months when stored in the original sealed Particle Size Max. 1 mm Temperature Range 8-9 lt water / 25 kg powder Workable Life (EN ) 5-7 hours Correction Time (EN ) 5-7 min. Compressive Strength / Class (EN ) 5 N/mm²/M5 Air Content (EN ) < % 20 Bond Strength (EN 998-2) 0.3 N/mm² (Table Value) Water Absorption Coefficient (EN ) 0.17 kg/m² min 0.5 Water Vapor Permeability, μ (EN 1745) 15/35 (Table Value) Thermal Conductivity (EN 1745) NPD (EN )
8 24 Kalekim Tile Adhesives 1060 TECHNOMAX 30 Two Component Highly Deformable Tile Adhesive Two component, high performance cementitious flexible adhesive with reduced slip and extended opentime for ceramic tiles and stones. Exterior bonding of ceramic, granite or porcelain ceramics sized 40x40 cm up to 30 meter and 60x60 cm. up to 15 meter height. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Perfect adherence. Highly deformable, resistant to temperature changes. Resistant to all climatic conditions. Can be applied on vertical surfaces even. For bonding of heavy tiles without sagging. Extended open time. Wipe the back side of tiles with water if dusty. Pour 25 kg. of powder component into 5.75 litres of clean liquid slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension. (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOMAX 30 with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, TECHNO- MAX 30 should be applied also on the back of the tiles. (combined method) Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. In installation of large size tiles, lay the tiles horizontally and do not start to lay upper row before the below one Leave an expansion joint at every 4 meter and use KALEPOLYMAS. Tiles installed with TECHNOMAX 30 must not be subject to water for at least 24 hours. Powder component: Store in dry medium. Do not stack more than 10 Liquid component: Store in temperatures 5 C to 35 C in original sealed packing. Powder component: 25kg multi-ply paper bags, Liquid component: 5.75lt drums. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. C2TE S2 TS EN 12004, Class C2TE S2 T: Reduced slip E: Extended open time S2: Highly Deformable Technical Temperature Range Set to Light Foot Traffic -initial (after 28 days) Deformability (EN 12002) 1st component: Grey powder, 2nd component: White liquid place 5.75 litres liquid / 25 kg powder 1.5 hours 0.5 mm After 30 minutes 8 hours on wall; 24 hours after on floor 24 hours kg/m² (Combined Method) 5 mm-s2 Highly deformable
9 Kalekim Tile Adhesives RAPİTECH Fast Setting Tile Adhesive High performance, rapid setting and reduced slip cementitious adhesive for ceramic tiles and stones. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone and decorative bricks on cementitious renders, cementitious screeds and concrete. Rapid tiling of places like public buildings, cafes, supermarkets, airports, that has to be ready for use within one day. Bonding of tiles on existing ceramic tiles. Fast setting, Perfect adherence. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. Wipe the back side of tiles with water if dusty. Pour 25kg of RAPİTECH into 6-7 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application. Allow to stand for 5 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of RAPİTECH with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, RAPİTECH should be applied also on the back of the tiles. (combined method) Open time is 15 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. If joints can be grouted with FUGAFLEX or FUGASİM, the site may be open for use within 1 day. Tiles installed with RAPİTECH must not be subject to water for at least 3-4 hours. 25kg multi-ply paper bags. C2FT TS EN 12004, Class C2FT F: Fast Setting T: Reduced slip Technical Temperature Range -initial (after 28 days) -after 6 hours Grey powder place 6-7 litres water / 25 kg powder 45 minutes 0.5 mm After 15 minutes 3-4 hours 3-5 kg/m²
10 26
11 Kalekim Tile Adhesives TECHNOPOOL Waterproofing Tile Adhesive High performance, flexible, water resistant cementitious adhesive with extended open time and reduced slip for ceramic tiles and stones. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete. Bonding of all types and sizes of tiles and glass mosaics in swimming pools, Turkish baths, water tanks, basins and any other wet place. Bonding of ceramic tiles or granite on existing granite, ceramic, marble. Bonding of tiles on places where sudden temperature changes occurs like cold storage depots and over floor heat installations. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Perfect adherence. Highly deformable, resistant to temperature changes. Waterproofing. Extended open time. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. C2TE S2 TS EN 12004, Class C2TE, S2 T: Reduced Slip E: Extended Open Time S2: Highly Deformable Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. Wipe the back side of tiles with water if dusty. Pour 25 kg of TECHNOPOOL into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOPOOL with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, TECH- NOPOOL should be applied also on the back of the tiles (combined method). Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Technical Temperature Range -initial (after 28 days) Deformability (EN 12002) When TECHNOPOOL is used not only as an adhesive but also as a water insulation material, apply mortar both on the substrate and on back side of tiles (combined method). Alternatively, first apply a layer of 1-2 mm of TECHNOPOOL with reinforcement mesh at corners, then install the tiles after 24 hours. Tiles installed with TECHNOPOOL must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags Grey or White powder place litres water / 25 kg powder 6 hours 0.5 mm After 30 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m² 5mm-S2 Highly deformable
12 28 Kalekim Tile Adhesives 1066 TECHNOFULL Fast Setting Pourable Tile Adhesive High performance, fullcontact & fast setting cementitious flexible adhesive, with extended open time for ceramic tiles and stones. Interior and exterior floor bonding of medium and large sizes of ceramic tiles, granite ceramic, porcelain ceramic, cotto, clinker, marble without the need of backbuttering. Bonding on floors over underfloor heating installations. Bonding on the floors of places subject to heavy traffic like shopping malls, hospitals, schools. Rapid tiling of places like public buildings, cafes, supermarkets, airports, that has to be ready for use within one day. Less consumption, labor-cost effective. 100% coating on the back of the tiles without applying any pressure. Fast setting, Perfect adherence. Semi-fluid consistency, easily trowellable, long open time. High flexibility Resistant to temperature changes. TECHNOFULL may be applied on surfaces up to 2cm thickness. Use TAMİRART or MASTAR 10 in case of any loose and uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. Pour 20 kg of TECHNOFULL into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table). Suitable for bonding of medium and large sizes of tiles on the floors of places subject to heavy traffic without the need of backbuttering. Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. If joints can be grouted with FUGAFLEX or FUGASİM, the site may be open for use within 1 day. Tiles installed with TECHNOFULL must not be subject to water for at least 3-4 hours. 20 kg multi-ply paper bags C2FE TS EN Class C2FE F: Fast Setting E: Extended open time Technical Temperature Range -initial (after 28 days) -after 6 hours Grey powder place lt water / 20 kg powder 2 hours After 3-4 hours 3-5 kg/m² After 30 minutes
13 Kalekim Tile Adhesives TECHNOLIGHT Lightweight, Highly Deformable Tile Adhesive Cementitious, high performance, flexible, lightweight tile adhesive including rubber and nano technological additives with extended open time and reduced slip. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tile, granite. Bonding of tiles on painted walls and gypsum. Bonding of ceramic tiles in swimming pools, basins and any other wet places. Bonding of tiles on terraces and balconies. Bonding of tiles on places where sudden temperature changes occurs like cold storage depots, on walls of ovens.and over floor heat installations. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Approx. 40% less consumption than standard adhesives. Thus, accomplish the same job with 15 kg package instead of 25 kg standard adhesive. High flexibility with rubber fillers. With its nano technological raw materials, it has high adhesion strength. Easy to carry with light weight and package with handles. C2TE S2 TS EN Class C2TE, S2 T: Reduced Slip E: Extended Open Time S2: Highly Deformable Environmentally Friendly Highly deformable, resistant to temperature changes. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. Extended open time. and sufficiently dry. Use TAMİRART or MASTAR 10 in case of any loose and uneven substrates to get a sound and flat surface. Wipe the back side of tiles with water if dusty. Apply KALEKİM DOLGULU ASTAR on plaster surfaces prior to the application. Use GYPSASTAR on anhydrite screeds. Pour 15 kg of TECHNOLIGHT into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOLIGHT with the flat side of trowel, then notch with the toothed side of trowel. Technical Temperature Range -initial (after 28 days) Deformability (EN 12002) of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, TECHNOLIGHT should be applied on the back of the tiles (combined method). Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with TECHNOLIGHT must not be subject to water for at least 24 hours. safety data sheet. Do not add any component which is not mentioned in application. bags on top of each other. 15 kg multi-ply paper bags with handles. Grey powder place. (+5 C) (+35 C) lt water / 15 kg powder 6 hours 0.5mm After 30 minutes 8 hours on wall; 24 hours after on floor kg/m² 5 mm - S2 Highly deformable
14 30 Kalekim Tile Adhesives 1070 KALEKİMTOZUMAZ Dust-Free Ceramic Tile Adhesive Dust-free cementitious ceramic tile adhesive with extended open time and reduced slip. Floor and wall bonding of all types of ceramic tiles, mosaic and decorative bricks on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles. User friendly with dust-free technology. Perfect adherence. Allows installation of tiles from top towards the bottom. Extended open time. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Wipe the back side of tiles with water if dusty. Pour 25 kg of KALEKİMTOZUMAZ into litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of KALEKİMTOZUMAZ with the flat side of trowel, then notch with the toothed side of trowel. Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes, If this period exceed, scratch and discard the mortar. Tiles installed with KALEKİMTOZUMAZ must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags. C1TE TS EN 12004, Class C1TE 1: Normal setting T: Reduced slip E: Extended Open Time Environmentally Friendly Technical Temperature Range -initial Grey powder place lt water / 25 kg powder 6 hours 0.5 mm After 30 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m²
15 Kalekim Tile Adhesives SUPERTECH Ready to Use Tile Adhesive Ready to use high performance emulsion polymer based tile adhesive with extended open time and reduced slip for ceramic tiles and stones. Easy and clean application for interior wall and floor bonding of all types and sizes of ceramic tiles even on deformable surfaces Bonding of tiles on gypsum panels and painted walls Bonding of Ecocarat Interior bonding of insulating and decorative ceiling materials. Ready to use. Perfect adherence. Highly deformable, resistant to normal vibrations to which building materials are subject. Extended open time. Allows installation of tiles from top towards the bottom. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Mix SUPERTECH thoroughly before application. Spread the SUPERTECH onto the substrate with notched trowel of which notch size is appropriate to the tile dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of SUPERTECH with the flat side of trowel, then notch with the toothed side of trowel. Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the paste. Insulating panels and decorative ceiling tiles can be applied either spot-bonding or full bonding. Tiles installed with SUPERTECH must not be subject to water for at least 10 days. While bonding the tiles on existing tiles, curing time may increase increase up to 1-2 weeks. Although SUPERTECH is non hazardous, use normal precautions for handling chemical products. For further information refer to Store in dry and cool medium. 1.5 kg, 5 kg, 15 kg and 30 kg pail. D2TE TS EN 12004, Class D2TE D: Dispersion based T: Reduced slip. E: Extended Open Time Technical Temperature Range Shear Adhesion Strength (EN 1324) -initial (after 28 days) -at elevated temperatures White paste place. 0.5 mm After 30 minutes hours kg/m² (-30 C) - (+80 C)
16 32 Kalekim Tile Adhesives 1411 TECHNOPUR Solvent-free Polyurethane Adhesive Two component, solvent-free polyurethane based multi-purpose adhesive. Bonding ceramic, granite ceramic, on concrete, metal, fibre-cement, wood, plasterboard surfaces. Bonding parquet. Bonding on floors over floor heating installations. Bonding thin tiles (Kalesinterflex ) reinforced with fibre mesh. Solvent-free. Excellent flexibility. Perfect adherence For floor heating systems, the heating should start ten days earlier and be stopped at the time of application. System can be reoperated 72 hours after the application. Mix kg component A with kg component B until a homogeneous color is obtained. Spread the mixture onto the substrate with notched trowel of 4x4x4 mm size. In bonding, sizes 40x40 cm or larger, apply the mixture using backbuttering method. Bonding of tiles and parquets on the substrate surfaces must be applied in minutes. tools and surface with polyurethane cleaning materials. Contains Difenylmethane diisosyanate which can be harmful. Do not breathe vapor. Use in well ventilated areas. In case of contact with skin and eyes rinse immediately with plenty of water and seek medical advice. Wear suitable protective clothing, gloves and eye protection. Keep away from children. Keep products as lids closed. Store in dry medium. 7 kg pail (2 components). and sufficiently dry. Cementitous substrates must be Use TAMİRART or MASTAR 10 in case of any loose and uneven substrates to get a sound and flat surface. R2T TS EN Class R2T R: Resin based T: Reduced slip Technical (at 23 C and 50% RH) Color Component A: Light yellow. Component B: Dark brown. 12 months when stored in the original sealed packing in dry place. Component A: 6.25 kg Component B: 0.75 kg Pot life minutes. Setting Time 80% hardening in 24 hours. 100% hardening in 1 week. 0.5mm ~ 1.5 kg (4x4x4 mm. notched trowel). Shear Adhesion Strength (TS EN 12003) - inital 2 N/mm 2 - after immesion in water 2 N/mm 2 - after thermal shock 2 N/mm 2 Service Temperature Range (-30 C) - ( +80 C)
17 33
18 34 Kalekim Yapı Kimyasalları
ELASTOCEM. Technical features. Applications. Two-component flexible, waterproofing and protective cementitious grout.
Two-component flexible, waterproofing and protective cementitious grout. 1504-2 PI-MC-IR Technical features Two-component grout, based on cements, selected aggregates, special additives and synthetic polymers
More informationRetail Price List 2015
Retail Price List 2015 SETTING MORTARS SERVOFLEX TRIO SUPER TEC Flexible Full Transfer Thin Set and Medium Bed Mortar 20 KG Flexible, cement-based thin set and medium bed mortar with polymer additive for
More informationConstruction. 3-part thixotropic epoxy patching mortar. Product Description. Tests
Product Data Sheet Edition 05/12/2014 Identification no: 020204030010000044 Sikadur -41 CF Rapid 3-part thixotropic epoxy patching mortar Construction Product Description Uses Characteristics / Advantages
More informationALKALI-RESISTANT WATERPROOFING AND DECOUPLING MEMBRANE UNDER CERAMIC TILES AND NATURAL STONE
Mapeguard WP System ALKALI-RESISTANT WATERPROOFING AND DECOUPLING MEMBRANE UNDER CERAMIC TILES AND NATURAL STONE Products used: Mapeguard WP 200, Mapeguard ST, Mapeguard IC, Mapeguard EC, Mapeguard WP
More informationMold Preventing I nterior System
interior insulation and renovation boards A system of components that have been designed to work perfectly together to repair damage caused by mold. The system consists of boards, insulation wedges, reveal
More informationLATICRETE 290 Premium Floor and Wall Thin-set Adhesive PRODUCT DESCRIPTION
LATICRETE 290 Premium Floor and Wall Thin-set Adhesive PRODUCT DESCRIPTION LATICRETE 290 Premium Floor and Wall Thin Set Adhesive is a high performance bagged cementitious powder to be mixed with either
More informationUltracolor CG2. Fast setting and drying grout for 2 to 20 mm joints, available in 26 colours; does not produce efflorescence
IN COMPLIANCE WITH EUROPEAN STANDARDS Ultracolor CG2 CEMENTITIOUS GROUT Fast setting and drying grout for 2 to 20 mm joints, available in 26 colours; does not produce efflorescence WHERE TO USE Interior
More informationkalox-pool draft 231 repairing refurbishing and finishing KALOX-POOL Waterproof cement-based mortar for protecting and finishing concrete.
kalox-pool draft 231 KALOX-POOL Waterproof cement-based mortar for protecting and finishing concrete. repairing refurbishing and finishing 8-30 C Trowel / Spray 4 mm kalox-pool EN 1504-2 MAIN FEATURES
More informationMineral waterproof coating PCI Dichtschlämme
Mineral waterproof coating PCI Dichtschlämme 305 for basement walls, swimming pools and potable water tanks With official test certificate. FIELDS OF For indoor and outdoor use. For walls and floors. For
More informationLow viscosity, solvent free elastic adhesive for wood flooring
Product Data Sheet Edition 25/06/2012 Identification no: 01 05 02 01 250 0 000009 SikaBond -54 54 Wood Floor Low viscosity, solvent free elastic adhesive for wood flooring Construction Product Description
More informationMapei systems for radiating floor heating with high thermal efficiency
Mapei systems for radiating floor heating with high thermal efficiency PRODUCTS FOR CERAMIC TILES AND STONE MATERIAL ADHESIVES SEALANTS CHEMICAL PRODUCTS FOR BUILDING III MAPEI systems for radiating floor
More information187123 REGGAE 30.3x34 cm./11.9"x13.4" D923. Natural Product that might suffer colour variations 1. PROPER PREPARATION OF SURFACE
187123 REGGAE 30.3x34 cm./11.9"x13.4" D923 Natural Product that might suffer colour variations 1. PROPER PREPARATION OF SURFACE The wall must be firm, levelled, dry and clean. Uneven surfaces greater than
More informationSEE HOW TO MAKE LIME PLASTER WHY USE LIME? PATTI STOUTER, BUILD SIMPLE INC. FEBRUARY 2013
SEE HOW TO MAKE LIME PLASTER PATTI STOUTER, BUILD SIMPLE INC. FEBRUARY 2013 WHY USE LIME? Lime plaster forms a light, clean, and durable surface that is resistant to weather and mold. A thin layer attaches
More informationWecryl Waterproofing System under surfacing supplied by others
Brief description The Wecryl waterproofing system allows a high-quality, seamless and crack-bridging waterproofing layer to be installed under loose-laid or bonded surfacing supplied by others (stone slabs,
More informationConstruction. Pre-Bagged Structural Waterproofing System. Product Description. Product Data. Tests. Form
Construction Product Data Sheet Edition 15/07/2013 Identification no: 01 07 05 04 001 0 000001 Sika 1 Pre-Bagged Structural Waterproofing System Product Description Pre-Bagged Structural Waterproofing
More informationWATERPROOFING OF WET ROOMS
WATERPROOFING OF WET ROOMS Waterproofing under tiles For longterm enjoyment of a wetroom area a complete and resistant waterproofing system is an important precondition. Most tiles are by themselves waterproof
More informationThermocem. unicem. Mortar additive. Mortar additive. unicem. Thermocem. Substrate preparation. products. Features: Recommended uses:
Mortar additive Mortar additive unicem Facades Thermocem Façades unicem is a latex that enhances the overall mechanical performance of cement-based mortars. Specially recommended for cement rendering,
More informationWOOD FLOORING ADHESIVES
dispersion adhesive 2 component adhesive MS polymer adhesive WOOD FLOORING ADHESIVES PROFESSIONAL PRODUCTS SOUDAL, leading adhesive manufacturer WOOD FLOORING ADHESIVES Soudal NV, located in Turnhout (B)
More informationNatural Thin Stone Veneer
Natural Thin Stone Veneer Until recently, if a project called for the natural look of stone but could not support its weight or thickness, the options were limited to manufactured imitation stone. More
More informationConstruction. Sikadur-Combiflex. Sealing system for cracks and problem joints with large movements DESCRIPTION
Sikadur-Combiflex REVISED JULY 2002 Sealing system for cracks and problem joints with large movements Construction DESCRIPTION USES ADVANTAGES The Sikadur-Combiflex joint sealing system consists of two
More informationHigh Performance Building Materials SCREEDS REPAIR MORTARS LEVELLING & SMOOTHING WATERPROOFING TILE ADHESIVES & GROUTS PRIMERS & ADDITIVES
High Performance Building Materials SCREEDS REPAIR MORTARS LEVELLING & SMOOTHING WATERPROOFING TILE ADHESIVES & GROUTS PRIMERS & ADDITIVES ARDEX manufacture a complete range of high performance building
More informationOLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. GeneralShale.com
OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide GeneralShale.com OLD BRICK ORIGINALS THIN BRICK VENEER Page 2 INTRODUCTION Check local building codes for proper installation guidelines
More informationDivision 9. SignaFlor Pad and Pour Flooring System
Division 9 SignaFlor Pad and Pour Flooring System SPECIFICATIONS Page 1. General... 2 1.1 Description 2 1.2 Quality Assurance 2 1.3 Submittals 2 1.4 Delivery and Storage 3 1.5 Warranty 3 1.6 Working Conditions
More informationResurfacing Concrete. Page 1 of 5
Resurfacing Concrete Materials List QUIKRETE Concrete Resurfacer (No. 1131) (see calculator on page 5 for quantity needed) QUIKRETE Concrete and Stucco Wash (No. 8601) QUIKRETE Concrete Sealer (No. 8800)
More informationLAYING BLOCK AND BRICK
LAYING BLOCK AND BRICK Products highlighted in this section: SAKRETE Type N Mortar Mix SAKRETE Type S Mortar Mix Brick And Block Laying Basics The first step in building a brick or block wall is to construct
More informationAdhesive Recommendation for Altro Flooring. Porous (absorbent) subfloors (most wood subfloors and some concrete)
Adhesive Recommendation for Altro Flooring Product Safety Sheet Flooring Smooth Sheet Flooring Porous (absorbent) subfloors (most wood subfloors and some concrete) Altrofix 30/31 (excessively heavy rolling
More informationSTAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM
STAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM Installed in Pre-engineered Steel Buildings Provides Lowest Cost Construction Method for CORROSIVE AND WET Environments PREFERRED SOLUTIONS, INC.
More informationImproving the flood resistance of your home. Advice sheet 4: Flood-resilient walls.
Improving the flood resistance of your home Advice sheet 4: Flood-resilient walls. This sheet provides guidance on identifying different types of wall, and reducing the flow of floodwater through them
More informationSC2000 CEMENT BONDING PROCEDURES
Pg.1 SC2000 CEMENT BONDING PROCEDURES Widely recognized as the world s finest cold vulcanizing cement REMA SC2000 is the solution to your industrial bonding problems. By using REMA UTR20 hardener with
More informationSaint Gobain Gyproc India Ltd. (Formerly India Gypsum Ltd.)
Saint Gobain Gyproc India Ltd. (Formerly India Gypsum Ltd.) Gyproc Plasters The cracks in cement sand plaster are an inherent feature which cannot be completely prevented but can only be controlled and
More informationK2 STONE NATURAL VENEER
INTRODUCTION WHAT IS K2 NATURAL THINSTONE VENEER? Natural K2 Stone veneer is real stone, cut 1 inch thick, making it light enough to be installed as a veneer. Sometimes referred to as thin veneer, thin
More informationVanishing Lid Trays Construction Methods with Tile or Masonry
1-800-447-2838 Installation Instructions Vanishing Lid Trays Construction Methods with Tile or Masonry Table of Contents 1. Tools and Equipment...1 2. Vanishing Lid Trays...3 2.1 Materials for Finished
More informationTechnical Data Sheet Art. No. 1810. Kiesol. applications. Shelf-life. rate depending on application. Characteristic data of the product
Page 1 of 5 Technical Data Sheet Art. No. 1810 Kiesol Deep protection silicification for waterproofing and refurbishing old and new buildings in the Kiesol System according to WTA Code of Practice 4-4-04/D
More informationPhoto courtesy of Delta Stone, Heber City, UT. Installation Solutions for: Manufactured Stone, Natural Thin Veneer, and Thin Brick
Photo courtesy of Delta Stone, Heber City, UT Installation Solutions for: Manufactured Stone, Natural Thin Veneer, and Thin Brick THIN VENEER INSTALLATION SYSTEMS PREMIUM BONDING MORTARS Premium PCL Stone
More informationConcrete Repair. Applications and Procedures
Concrete Repair Applications and Procedures Objectives Identify what surface preparation is needed Identify typical modes of failure and testing methods How to choose the correct material for the repair
More informationSchlüter -KERDI-BOARD Substrate, structural panel, bonded waterproofing
Substrate, structural panel, bonded waterproofing The universal substrate for tiles Perfect covering No matter whether you work with mosaics or large format tiles, an absolutely level substrate with straight
More informationCORROSION ENGINEERING RESIN-BASED POLYMER CONCRETES AND GROUTS
AN ERGONARMOR COMPANY TECHNICAL INFORMATION SPECIFICATION FOR INSTALLATION 07/11 SUPERSEDES 04/00 PAGE 1 OF 6 CORROSION ENGINEERING RESIN-BASED POLYMER CONCRETES AND GROUTS 1. SCOPE 1.1 This specification
More informationcement Masonry Cement Engineered for quality and reliability, Lafarge cements for masonry deliver consistent performance. page 2 Lafarge Cement
cement Masonry Cement Engineered for quality and reliability, Lafarge cements for masonry deliver consistent performance. page 2 Lafarge Cement Lafarge in North America The Lafarge Group is the world leader
More information12.1 Schlüter -KERDI-BOARD
I n n o v a t i v e p r o f i l e s 12.1 Schlüter -KERDI-BOARD S u b s t r a t e U N I V E R S A L S T R U C T U R A L P A N E L, B O N D E D W A T E R P R O O F I N G Application and Function Schlüter
More informationAnnex of the certificate (Page 1/6) Accreditation Scope
As a Testing Laboratory Annex of the certificate (Page 1/6) Accreditation Scope Address: Küçük Çiğli Mh. 8780/1 Sk. No:5 Çiğli 35681 İZMİR / TÜRKİYE Phone : 0 232 376 24 25 Fax : 0 232 386 33 98 E-Mail
More informationShower Walls and Tub Surrounds
Reverso en español TEC Skill Set How-To Project Guide Shower Walls and Tub Surrounds 3 Steps to a Beautiful Tile Surface! 1. Prepare the surface 2. Set the tile 3. Grout and caulk H.B. Fuller Construction
More informationInstallation Solutions for: Manufactured Stone, Natural Thin Veneer, and Thin Brick ARCHITECTURAL SPECIFICATIONS / CAD MODELS TVISTM WARRANTIES
ARCHITECTURAL SPECIFICATIONS / CAD MODELS With more than 40 years of manufacturing high quality, innovative building products in the commercial and residential markets, Custom Building Products TVISTM
More informationVinyl Composition Tile Installation System
Vinyl Composition Tile Installation System Product Gauge Size Vinyl No-Wax (Dry Back) Urethane No-Wax (Dry Back) 0.045" (1.1 mm) 0.080" (2.0 mm) IMPERIAL TEXTURE 0.094" (2.4 mm) STONETEX ChromaSpin COMPANION
More informationThin Veneer Stone Installation Guide
Thin Veneer Stone Installation Guide Complete step by step How-to guide for installing Thin Veneer Stone. Important: From pallet to pallet of natural thin veneer stone, as with any natural stone product,
More informationTecnoepo Flooring System 185
Certificate ICMQ 1305-CPD-0808 Approved Standard EN 1504-2 prospect ZA.1f Direttive 89/106/CEE TECNOCHEM E LEED LEED Leadership Energy Environmental Design THE PRODUCTS: Primer TECNOFIX EP 110 Primer two-component
More informationMILMAN & ASSOCIATES STRUCTURAL CONSULTING ENGINEERS/ PROJECT MANAGERS
MILMAN & ASSOCIATES STRUCTURAL CONSULTING ENGINEERS/ PROJECT MANAGERS May 29, 2013 Revision B Structural Guideline for Design and Installation Holes in Composite Floor Slab Terminal 3, Departure Level
More informationELECTRIC PERISTALTIC MORTAR POINTING PUMP
ELECTRIC PERISTALTIC MORTAR POINTING PUMP pointing gun & control valve ACF405 PERISTALTIC PuMP hopper feed roller & tube pump for refurbishment & repair trades heritage & conservation bridge & underground
More informationRESTORATION + DECORATION OF BALCONIES AND TERRACES. Decorative, Easy to Maintain and Slip-Resistant Surfaces
RESTORATION + DECORATION OF BALCONIES AND TERRACES Decorative, Easy to Maintain and Slip-Resistant Surfaces BALCONIES AND THEIR LOADS For that extra bit of pleasure, the Remmers Balcony and Terrace Programme
More informationMinor Cracks in Horizontal Surfaces
Cracks, chips and broken or flaking areas in concrete are not only unsightly, they can lead to further deterioration of the surface. The result is a costly replacement project as opposed to a simple repair.
More informationInstallation System. Existing Resilient Sheet Floors
Vinyl Composition Tile Installation System Product Adhesive/Full Spread Adhesive/Tile-On Comment Imperial Texture MultiColor RAVE Stonetex Companion Square Feature Tile/Strips ARTEFFECTS SAFETY ZONE Vinyl
More informationCement Plaster. www.qatarplaster.com
Cement Plaster www.qatarplaster.com COMPANY PROFILE Qatar Plaster (QP) is a leading manufacturer of dry mix products based in Mesaieed Industrial City Doha, Qatar. Qatar Plaster (QP) has come up with a
More informationBLACK JACK ALL WEATHER ROOF COATING
PAGE: 1 of 6 PRINT DATE: 16/09/2004 BLACK JACK ALL WEATHER ROOF COATING DESCRIPTION BLACK JACK ALL WEATHER ROOF COATING is a solvent based, full bodied black brushable compound with added fibres for reinforcement.
More informationNEGATIVE SIDE WATERPROOFING SYSTEMS FOR MASONRY AND CONCRETE
NEGATIVE SIDE WATERPROOFING SYSTEMS FOR MASONRY AND CONCRETE What is negative side waterproofing? A typical case of negative side waterproofing is when water comes through the walls of a basement and the
More informationBEST PRACTICE GUIDE. Fibrelime Premixed Universal Plaster and Render
BEST PRACTICE GUIDE Fibrelime Premixed Universal Plaster and Render Contents: Fibrelime description Fibrelime suitability Preparation before application Application Aftercare Painting General Recommended
More informationHIGH PERFORMANCE PRE-APPLIED SYSTEM FOR BLIND SIDE & BELOW GRADE WATERPROOFING APPLICATIONS
BSW HIGH PERFORMANCE PRE-APPLIED SYSTEM FOR BLIND SIDE & BELOW GRADE WATERPROOFING APPLICATIONS BSW is a fully reinforced Pre-Applied system membrane designed for horizontal and vertical external blind-side
More informationpinta ACOUSTIC PANEL [1/7]
[1/7] Too much echo in the workplace? Staff unable to concentrate on their work? The answer is: ACOUSTIC PANEL. Service Call our telephone hotline for advice on your individual situation. Animated installation
More informationPRODUCT DATA SHEET Sika Cable System
PRODUCT DATA SHEET Corrosion protection for bridge cables of steel and galvanized steel PRODUCT DESCRIPTION The Sika Cable System consists of coating materials as well as a sealing respectively injection
More informationexternal Basement waterproofing
external Basement waterproofing Content Content 2 External Basement Waterproofing 3 What is positive side waterproofing? 3 KÖSTER Waterproofing Solutions The KÖSTER solutions for positive side waterproofing
More informationSite sampling and testing of concrete
Sampling amended booklet amended:layout 1 4/8/09 14:14 Page 1 A practical guide for site personnel Site sampling and testing of concrete Cubes have a vital role to test that the concrete strength meets
More informationTHINGS YOU SHOULD KNOW
INSTALLATION INSTRUCTIONS Value Sized Roll The quickest, easiest, cleanest way to install tile. No Mortar, No Mixing, No Mess Complete Your Project in a Day No Waiting Between Setting and Grouting THINGS
More informationHow to build a Pizza Oven in 4 days
How to build a Pizza Oven in 4 days Preparation day (slab) 1. Foundation 1500 deep x 1300 wide x 75mm deep Required 20 bags cement pre mix. If you already have a concrete base, you save this prep day DAY
More informationGigaCrete Specification PlasterMax
GigaCrete Inc. 6775 Speedway Blvd. Suite M105 Las Vegas, NV 89115 Ph (702) 643-6363 Fax (702) 643 1453 www.gigacrete.com GigaCrete Specification PlasterMax PlasterMax : Fire Rated Plaster for Direct Application
More informationThe AQUAFIN Approach to Concrete Repair
Concrete Repair Building Product Systems Waterproofing & Concrete Restoration Decorative Coatings Moisture Vapor Remediation & Flooring Injection Grouting The AQUAFIN Approach to Concrete Repair www.aquafin.net
More informationRHOPLEX MC-1834P Cement Mortar Modifier
RHOPLEX MC-1834P Cement Mortar Modifier Description is a low-odor acrylic polymer emulsion designed for modifying Portland cement compositions. The superior adhesion, ultraviolet light resistance, water
More informationFRAMED & MOUNTED TILE MURAL
Page 1 of 5 There is no denying that tile murals have taken the sublimation industry by storm. The unique ability to take a customer s artwork or high resolution photograph, tile it using your software
More informationConcrete Waterproofing Systems
Concrete Waterproofing Systems Triton s concrete waterproofing systems are designed for the protection and waterproofing of new or existing concrete structures. The range includes integral waterproofing
More informationDry construction compounds
Dry construction compounds 1 Company Introduction MFC MORFICO s.r.o. was founded in 1991 as a construction company specializing in the treatment of industrial concrete fl oors and areas. During this period
More information3 Marine Adhesives and Sealants
3 Marine Adhesives and Sealants For Demanding Marine Environments Providing secure bonds, in the water or out. Almost no environment is harsher than the beating sun and pounding waves of the open water.
More informationWaterproofing System for Wastewater Tanks in Petrochemical Industries and Refineries
Waterproofing System for Wastewater Tanks in Petrochemical Industries and Refineries Introduction Wastewater of petrochemical industries and refineries contains high amounts of emulsified aliphatic or
More informationWaterproofing construction Joints
WaterproofingSystems Waterproofing construction Joints Area waterproofing Backing rod KÖSTER Joint Sealant FS-H KÖSTER FS Primer Contents Basics Connective, loadable and resilient: Joints in building construction
More information12 POLYURETHANE ADHESIVE (PU 105)
12 POLYURETHANE ADHESIVE (PU 105) DISCLAIMER: Refer to page 5 of this document. 12.1 DESCRIPTION PU 105 is a high performance two-part polyurethane adhesive for both indoor installations of Mondo rubber
More informationexternal Basement waterproofing
external Basement waterproofing Content External basement waterproofing Content 2 External Basement Waterproofing 3 What is positive side waterproofing? 3 KÖSTER Waterproofing Solutions The KÖSTER solutions
More informationHigh-performance, 2-part epoxy anchoring adhesive
Product Data Sheet Edition 27/04/2009 Revision no: 0 Identification no: 01 04 02 06 001 0 000030-3+ -3+ High-performance, 2-part epoxy anchoring adhesive Construction Product Description Uses Solvent-free,
More informationSikaBond Adhesive Systems for Floor Coverings. Innovation & Consistency. since 1910
SikaBond Adhesive Systems for Floor Coverings Innovation & Consistency since 1910 Sika s Comprehensive Competence in Flooring Sika has an extensive range of products for use in many different types of
More informationSwimming Pool Tiling Specialists
SCREEDS RENDERS WATERPROOFING TILE ADHESIVES GROUTS SILICONES Swimming Pool Tiling Specialists WHERE QUALITY MATTERS The Aquatics Centre, Olympic Park, London 2 Our company s heritage dates back more than
More informationRAW INSTALLATION GUIDE
SUGGESTIONS / FACTORS TO BE TAKEN INTO CONSIDERATION BIANCO CARRARA The small holes, commonly referred to as "tarolo", are a natural characteristic of bianco carrara. In the Raw finish, this characteristic
More informationHigh Capacity Hot Air Dryer
High Capacity Hot Air Dryer MADE IN AUSTRIA autumn 2015 www.zimmer-austria.com page 1 Hot air dryer type: Compact HC The modular construction of the high efficiency and powerful hot air nozzle dryer is
More informationFACT SHEET: HYDRATED LIME FOR MASONRY PURPOSES
FACT SHEET: HYDRATED LIME FOR MASONRY PURPOSES Hydrated Masons Lime Characteristics Type S (Special) hydrated lime is a fine, white, high purity product which has been specially hydrated for convenient,
More informationProfiles for floors of same height Cerfix Projoint
PROFILPAS S.P.A. VIA EINSTEIN, 38 35010 CADONEGHE (PADOVA) ITALY TEL. +39 (0)49 8878411 +39 (0)49 8878412 FAX. +39 (0)49-706692 EMAIL: INFO@PROFILPAS.COM s for floors of same height Cerfix Projoint Application
More informationFIXIT.CH. Aerogel Insulating Plaster System. Handling Guidelines. Easy to use. Mineral based. 0.028 W/mK BAUSTOFFE MIT SYSTEM
FIXIT.CH Aerogel Insulating Plaster System Handling Guidelines BAUSTOFFE MIT SYSTEM λ 0.028 W/mK Mineral based Easy to use Efficient building insulation using space technology Aerogel high-performance
More informationPRODUCT DESCRIPTION 29/08/2014
29/08/2014 PRODUCT DESCRIPTION Quartz Carpet is a seamless flooring system based on coloured or uncoloured quartz grains that are bonded with resin (epoxy or polyurethane). This system is used for houses,
More informationChimney systems ICOPAL WULKAN C/CI/C-eko/CI-eko
INSTALLATION MANUAL Chimney systems ICOPAL WULKAN C/CI/C-eko/CI-eko Ventilated Notified entity Building Technical and Research Institute Prague notification no. 1020 This instruction refers to double-layer
More informationNCMA TEK CONCRETE MASONRY FOUNDATION WALL DETAILS. TEK 5-3A Details (2003)
NCMA TEK National Concrete Masonry Association an information series from the national authority on concrete masonry technology CONCRETE MASONRY FOUNDATION WALL DETAILS TEK 5-3A Details (2003) Keywords:
More informationPanelTack HM. for the bonding of SVK Ornimat SKG 08.08.056.02
PanelTack HM for the bonding of SVK Ornimat Product Simson PanelTack HM is a moisture curing, elastic adhesive based on SMP (Silyl Modified Polymer). PanelTack HM is solvent- and isocyanate free. s Bonding
More informationManufactured Stone and Thin Brick Installation Systems
Manufactured Stone and Thin Brick Installation Systems A Variety of System Options, Including for High-Performance, Efflorescence-Free and Fast-Setting Systems Best-Backed System Warranty Technical Support
More informationCEILING SYSTEMS. CI/SfB (35) Xy April 2006. [Between us, ideas become reality.] ULTIMA CANOPY. Data sheet. Acoustic performance meets High Design
CEILING SYSTEMS [Between us, ideas become reality.] CI/SfB (35) Xy April 2006 ULTIMA CANOPY Data sheet Acoustic performance meets High Design ULTIMA CANOPY Installation Instructions I. GENERAL 1. Product
More informationfirst look at GigaCrete s revolutionary new New Construction GigaHouse GigaHouse Utilizing GigaPanel
first look at GigaCrete s revolutionary new New Construction GigaHouse GigaHouse Utilizing GigaPanel What is GigaCrete GigaCrete is a family of products based on low carbon footprint Green ceramic binders
More informationExTERNAL BASEMENT WATERPROOFING
ExTERNAL BASEMENT WATERPROOFING Contents Contents 2 Introduction External basement waterproofing 3 What is positive side waterproofing? 3 Waterproofing Solutions The KOSTER solutions for positive side
More informationFERMACELL Powerpanel H 2 O for Wet & Moisture affected areas
FERMACELL Powerpanel H 2 O for Wet & Moisture affected areas Powerpanel H 2 O is a cement based board from FERMACELL. Board Characteristics Board Thickness 12.5 mm Board Sizes 1000 x 1200 mm 50 sheets/pallet
More informationCavity Drain R20 is manufactured from1.0mm thick black high density polyethylene with studs approximately 20mm high.
CI/SfB Tn6 L6813 September 2013 RIW CAVITY DRAIN R20 R20 is manufactured from1.0mm thick black high density polyethylene with studs approximately 20mm high. Other systems are available for specific uses,
More informationHerringbone Pattern Flooring
Herringbone Pattern Flooring If it s not marked NOFMA, it s not certified. Handling, Storage, Installation and Tips Herringbone is generally manufactured from 3/4 x 2 ¼ or ¾ x 1-1/2 standard tongue & groove
More informationSection 4: Architectural Design
Section 4: Architectural Design 4.1 Design Flexibility and Compatibility...3 4.2 Moisture Protection...3 4.3 Surface Treatments...6 4.4 Exterior Surface Treatments...6 4.5 Interior Surface Treatments...8
More informationUSER GUIDE Easier, Safer, Betta! www.gripsetbetta.com WATERPROOFING
USER GUIDE Easier, Safer, Betta! www.gripsetbetta.com WATERPROOFING Welcome to Gripset Betta, Over the past 3 decades through the tireless commitment to improve and enhance the way buildings are waterproofed,
More information(T indicates a Tropicalised version with extended workability. No change has been made to the formulation)
928 T (T indicates a Tropicalised version with extended workability. No change has been made to the formulation) High strength, non-shrink cementitious grout Description 928 T is a ready to use product
More information2.18 INTERIOR & EXTERIOR FINISHES 2.18.1 VAPOR & AIR BARRIERS
2.18 INTERIOR & EXTERIOR FINISHES 2.18.1 VAPOR & AIR BARRIERS The LOGIX wall assembly has no need for an additional vapor barrier, the solid concrete core covered with the low permeance EPS (Type II) foam
More informationG4 is browny translucent in colour and is effected by UV light. Therefore it is for internal use unless top coated to protect it from UV light
G4 Damp Seal is a polyurethane that hardens with moisture. It is browny tranclucent in colour. G4 provides a tough, highly durable non-porous seal on most porous materials. Since G4 is hardened by moisture
More informationTECHNICAL DATA SHEET. TOPECA, Lda Rua do Mosqueiro 2490 115 Cercal Ourém PORTUGAL. Tel.: 00 351 249 580 070 Fax.: 00 351 249 580 079
TECHNICAL DATA SHEET TOPECA, Lda Rua do Mosqueiro 2490 115 Cercal Ourém PORTUGAL Tel.: 00 351 249 580 070 Fax.: 00 351 249 580 079 geral@ topeca. pt www.topeca.pt juntaemcor plus+ Pág. 2 Sanded texture
More informationRIW SHEETSEAL 226 BENEFITS APPLICATIONS APPLIED TO. CI/SfB TN6 L6813. November 2013. l Water and water vapour barrier. l Factory controlled thickness
CI/SfB TN6 L6813 November 2013 RIW SHEETSEAL 226 is a cold applied, high density polyethylene film, coated with a bitumen/rubber self adhesive layer with a removable reinforced silicone paper. Primer is
More informationSection 04810 EXTERIOR STONE VENEER Full Mortar
Full Mortar PART 1 GENERAL 1.1 SUMMARY A. Section includes: 1. Portland cement mortar bed 2. Stone Veneer 3. Expansion and control joints. 4. Portland cement and hydraulic mortar and grout. 5. Sealer and
More information