Dry construction compounds

Transcription

1 Dry construction compounds 1

2 Company Introduction MFC MORFICO s.r.o. was founded in 1991 as a construction company specializing in the treatment of industrial concrete fl oors and areas. During this period of activity we achieved an important position on the construction market during the implementation of new progressive technologies. The extensive experience acquired from abroad was applied during the development of our own materials from domestic raw materials, which are a guarantee for high quality and productivity. We gradually transferred from the application of to the production and sale of construction materials. Year 2000 completion of production line for dry cement mixtures. Products are used for surface treatment of concrete areas, they are delivered in paper bags or freely placed. Year 2002 expansion of the production program by fresh anhydride screeds which are delivered to the construction sites in car-mixers or on a special application trailer. Year 2004 commissioning of a new production line for production of construction wall parts which represent a sacrifi cial framework for load-bearing concrete and, at the same time, are conductors for thermal insulation. Year 2006 commencement of production of protective coating substances used for special surface treatment of concrete areas, they are delivered in liquid status and self-levelling coats. Year 2008 expansion of services related to deliveries of screeds. Transport of dry mixture to the construction site, mixing of the required volumes of fresh screeds and pumping to the place of destination. Year 2010 prefabrication of wall panels from wood-cement shaped units, including assembly of the shell construction. Production of acoustic shaped units, for surface treatment of noise barriers. Year 2012 production of special cement binder as the alternative to anhydrite coats, delivered to the construction by BRE- MAT application vehicles. Year 2014 construction of fi lling and distribution centres Brno, Prague, České Budějovice and Hradec Králové, for expansion of services of accessibility of our production. At present we offer a wide assortment of products which fi nd use in the applications of modern methods used for fl at, civil and industrial constructions. We have built a high quality network of commercial representation, application companies, dealers and consultants in the Czech Republic, as well as abroad. We are holders of the ISO 9001 certifi cate. The registered capital of the company is CZK 5,000,000. Full time employees: 50 Ing. Oldřich Fiala Director of the Company Certifika ní spole nost Výzkumný ústav pozemních staveb ISO

3 MFC Screeds 020 Cast levelling coats Anhydrite binder MFC Anhydrit 020 screed mixture on the basis of calcium sulphate (anhydrite), designed for cast levelling (base) layers of fl oors under fl oor covers in civil and apartment constructions. Resistance to pressure min. 20 MPa. Recommended thickness of the layer (depending on the selected composition) mm. Cement binder Areas of application: Materials are designed for levelling layers on new and old fl oors in civil and residential constructions as the base under the fi nal surface treatment (e.g. fl ooring, carpets, fl oating fl oors, PVC). MFC Portland 020 Cast foam concrete MFC Porocem 010 Cast cement foam designated for the levelling (base) and insulating layers of fl oors, mainly in residential, civil and industrial objects. Pressure strength min. 20, 25 and 30 MPa. Recommended thickness of layer (depending on the selected composition) mm. cast cement foam designated for the levelling (base) and insulating layers of fl oors, mainly in residential, civil and industrial objects. Density k/m 3. Recommended thickness of layer mm. Represents an ideal base under cast anhydrite abd cement coat as the substitution of common board insulations. Cast coats are delivered by means of mobile sets (Bremat and TransMix), which enable economic and fast preparation of coat directly in the construction site, including pumping in the place of the placement. Heating screed MFC Anhydrite 020 MFC Portland 020 Separation layer Levelling of the base MFC Porocem 010 Plaster Side strip Heating screed Application vehicle

4 MFC Cobet 100 Dry-shakes, screeds Dry shake : thickness 2 3 mm (application by dry into wet system) MFC Cobet 110 MFC Cobet 115 MFC Cobet 120 (silica) is used for surface treatment of fresh concrete fl oors with light operation and lower demands for resistance to abrasion. (metalic) is designed for surface treatment of fresh concrete fl oors with medium heavy operation and increased demands for resistance to abrasion. (corundum) is used for surface treatment of fresh concrete fl oors with medium-heavy operation and increased demands for resistance to abrasion. Areas of use: Materials are used for surface treatment of fresh concrete fl oors in civil and industrial areas. They improve processing, level and resistance of the surface to abrasion. MFC Cobet 130 MFC Cobet 140 (corundum/carbide) is designed for surface treatment of fresh concrete fl oors with medium heavy operation and increased demands for resistence to abrasion (carbide) is used for surface treatment of fresh concrete fl oors with heavy operation and high demands for resistance to abrasion. Hardness of abrasion resistant filled according to Moshe: Silicon 4 Metalic 8,4 Corundum 9 Carbide 10 Surface treatment of the concrete floor-coat Surface treatment of the concrete floor with dry-shake Surface treatment of the concrete floor with screed Protective coat Impregnation MFC Cobet Impregnation MFC Cobet adhesive bridge

5 MFC Sanfix 200 Repair screeds and mortars Areas of use: Materials are used for repairs of local chuck holes and cuts on fl oors, stairs, walls, corners, etc. (binders) or as a protective, fi lling or fi nal layer of damaged concrete constructions (mortars). Screeds MFC Sanfix 210 MFC Sanfix 220 MFC Sanfix 230 Mortars MFC Sanfix 250 MFC Sanfix 251 MFC Sanfix 260 MFC Sanfix 261 professional - is used for fi ne fi lling of holes and cracks concrete fl oors, it is possible to use it on wooden, stone, ceramic tiles and fl oors. It is used in combination with other MFC levelling materials (MFC Level 300, MFC Final 400). It is applied in one 1 5 mm thick layer within one working step. standard - is used for fi ne binding of fi lling holes and cracks concrete fl oors, it is possible to use it on wooden, stone, ceramic tiles and fl oors. It is used in combination with other MFC levelling materials (MFC Level 300, MFC Final 400). It is applied in one 1 10 mm thick layer within one working step. special - is used for levelling of roughness, in particular concrete surfaces, for fi ne and rough binding of holes and cuts of fl oors, it can also be used for repair of walls, stairs, corners or for creation of a declined layer. It can also be used for wooden, stone, ceramic fl ooring and tiling. It is used in combination with other MFC levelling materials (MFC Level 300, MFC Final 400). It is applied in one 1 50 mm thick layer within one working step. waterproof is used for waterproof material for the protection of concrete constructions with an absorbent base. It is recommended for vertical and horizontal constructions in interiors and exteriors. This is used prior to the application of rehabilitation mortar and MFC sealing binders. anti-corrosive is used as a protective coat for reinforcement of concrete constructions after they have been cleaned of corrosion. At the same time, this plaster is used as an adhesive bridge to ensure adhesion of newly applied layers. fi lling is used for repair and re-profi ling of concrete constructions It is applied in one 5-50 mm thick layer within one working step. fi nal is used for thin layer repair and re-profi ling of concrete constructions It is applied in one 1-5 mm thick layer within one working step. Rehabilitation of local pool holes and cracks Levelling of the base during reconstruction of wooden floors Repair system for ferroconcrete constructions MFC Level 300, Final 400 MFC Sanfix 210, 220, 230 MFC Level 340 MFC Sanfix 210, 220, 230 wooden floor rough filling mortar MFC Sanfix 260 anti-corrosion coating MFC Sanfix 251 fine final mortar MFC Sanfix 261

6 MFC Level 300 Self-levelling screeds Wet into dry system Areas of use: Materials are used for levelling layers of new and old fl oors (concrete, ceramic, wood) in civil and fl at constructions as the base for fi nal surface treatment (e.g. fl owing, coating, parquets, carpets, PVC). MFC Level 304 MFC Level 305 MFC Level 310 MFC Level 320 MFC Level 330 MFC Level 340 MFC Level 350 smoothing screed is used for levelling of surfaces and minor roughness, in particular of concrete fl oors and declined areas as the base under fl oor covers. It is applied in one 1 5 mm thick layer within one working step. levelling screed is used for levelling of surfaces, in particular of concrete fl oors and declined areas as the base under fl oor covers. It is applied in one 5 30 mm thick layer within one working step. levelling screed is used for levelling of roughness, in particular of concrete fl oors as the base layer for the MFC Level 320 self-levelling screed or directly for the fi nal fl oor covering. It is applied in one 5 50 mm thick layer within one working step. base screed is used for levelling of fi ne roughness, in particular of concrete surfaces as the base levelling layer under the fl oor covers or as a fi nal surface treatment with a suitable coat for light operation. It is applied in one 2 30 mm thick layer within one working step. base fast-drying screed is used for levelling of fi ne roughness, in particular of concrete surfaces as the base fast drying levelling layer under the fl oor covers or as a fi nal surface treatment with a suitable coat for light operation. It is applied in one 2 30 mm thick layer within one working step. screed with spread reinforcement is used for levelling of mainly concrete surfaces, wooden fl oors, stone and ceramic fl ooring as a fl exible levelling layer under the fl oor covers. It is applied in one 5 50 mm thick layer within one working step. screed for fl oor heating is used for levelling of mainly concrete surfaces, wooden fl oors, stone and ceramic fl ooring as a fl exible levelling layer under the fl oor heating. It is applied in one 2 30 mm thick layer within one working step. Levelling of the base under walking layer Levelling of the base during reconstruction of wooden floors Levelling of the base with electric floor heating walking layer walking layer walking layer concrete base wooden floor cement screed thermal insulation electric cables concrete base

7 MFC Final 400 Self-levelling industrial screeds Wet into dry system Areas of use: Materials are used for fi nal topping areas of industrial fl oors as a fi nal surface treatment (new and old), in particular concrete areas with a high mechanical stress (e.g. production halls, garages, warehouses, supermarkets). MFC Final 410 MFC Final 411 MFC Final 412 MFC Final 413 MFC Final 420 MFC Final 430 MFC Final 440 fi nal screed, medium heavy operation - is used for industrial fl oors on new or old concrete as a fi nal surface treatment. It is used for levelling of surfaces affected by strong wearing. It is applied in one 4 15 mm thick layer within one working step. fi nal screed (corundum) - is used for industrial fl oors on new or old concrete as a fi nal surface treatment. It is used for levelling of surfaces affected by strong wearing and lower demands for resistance to abrasion. It is applied in one 4 15 mm thick layer within one working step. fi nal screed (corundum/carbide) - is used for industrial fl oors on new or old concrete as a fi nal surface treatment. It is used for levelling of surfaces affected by strong wearing and increased demands for resistance to abrasion. It is applied in one 4 15 mm thick layer within one working step. fi nal screed (carbide) - is used for industrial fl oors on new or old concrete as a fi nal surface treatment. It is used for levelling of surfaces affected by strong wearing and high demands for resistance to abrasion. It is applied in one 4 15 mm thick layer within one working step. base screed, medium-heavy operation is used for application on old and damaged concrete bases for rough levelling and compaction of industrial fl oors before the application of MFC Final or synthetic screed. It is applied in one 5 30 mm thick layer within one working step. fi nal screed, heavy operation - is used for industrial fl oors on new or old concrete as a fi nal surface treatment for heavy stressed industrial and concrete areas. It is applied in one 5 15 mm thick layer within one working step. base screed, heavy operation is used for application on old and damaged concrete bases for rough levelling and compaction of industrial fl oors before the application of MFC Final 430 or a synthetic screed. It is applied in one 5 30 mm thick layer within one working step. Final topping of industrial floors Surface treatment with final topping with underlayment screed during reconstruction of industrial floors Levelling of industrial floors under synthetic coat MFC Final , 430 synthetic coat MFC Final , 430 MFC Final 420, 440 MFC Final 420, 440

8 MFC Festic 500 Sealing adhesives MFC Festic 510 C1 MFC Festic 511 C1TE MFC Festic 512 C2TE standard adhesive is used in interiors for sealing of all types of tiling and fl ooring with the exception of stone high sintered fl ooring on traditional fi rm bases (lime-cement and cement plasters, concrete bases, etc.) professional adhesive used in interiors and exteriors for sealing all types of tiles and fl ooring (sintered and highly sintered) on traditional solid bases and in environments with increased demands for adhesion with the base. fl exible adhesive is used for sealing of all types of tiles and fl ooring in interiors and exteriors on traditional solid bases in the environment with increased demands for adhesion with the base (smooth concrete fl oors, plasterboard, terrazzo, wood, asphalt, old tiles and fl ooring). Areas of use: Materials are used for sealing and joining of tiles, fl ooring and heating systems, on various types of bases in interiors and exteriors. MFC Festic 512 AE adhesive for calcium sulphate bases designed for (anhydrite) C2TE bases, as well as traditional (concrete) bases. It can be used for sealing all types of interior fl oorings (sintered and highly sintered). MFC Festic 513 C2TE-S1 MFC Festic 520 MFC Festic 521 high fl exible adhesive used in interiors and exteriors for sealing all types of tiles and fl ooring (sintered and highly sintered) and in environments with increased demands for adhesion with the base. It is recommended for fl oor heating systems and bases with cross deformation. standard sealing adhesive for thermal insulation is used for manual sealing of traditional polystyrene heating boards on fi rm bases (plaster, bricks, concrete plasters). It is frost-proof and recommended for use in interiors and exteriors. special sealing adhesive for thermal insulation is used for sealing of heat-insulation boards made of extruded polystyrene on fi rm bases (plaster, bricks, concrete plasters). It is frost-proof and recommended for the use in interiors and exteriors. Sealing of tiles and flooring on traditional bases Sealing of flooring on anhydrite coats Sealing of polyester heat-insulation boards walking layer MFC Festic walking layer MFC Festic 512 AE MFC Anhydrit 020 (030) armovací tkanina MFC Festic 520, 521 tepelná izolace MFC Festic 520, 521

9 MFC Protect 600 Impregnation, penetration, coating Impregnating compound (surface area) MFC Stoplak 610 synthetic solution based on acrylic dispersion. The solution is used to treat both old and new surfaces of levelling MFC materials and standard concrete surfaces. MFC Ekopox K compound based on water epoxy resin dispersion. The compound is recommended for use as fi nal surface treatment of concrete surfaces and industrial self-levelling layers from the MFC Final 400 series. MFC Curol SiT60 is a protective coat preventing water evaporation from the surface of machine smoothed and fi lled industrial fl ooring. Within 6 8 weeks it effi ciently prevents any cracks originating during the settling and hardening of concrete. Areas of application: The compounds are designed for the preparation of base layers prior to the application of further layers or as fi nal surface treatment for concrete and self-levelling coating. Penetration compounds (base area) is a concentrated water-borne solution based on acrylic dispersion. The solution is designed to close and fi x foundations from concrete, wood, ceramics, etc. and acts as an adhesive bridge individual levelling layers from MFC materials. MFC Ekopox K compound based on water epoxy resin dispersion. The compound is designed to crose and fi x bases made from concrete, wood, ceramics, etc. and anywhere there are increased requirements for adhesion with the base layer. MFC Ekopox K solvent-free system based on epoxy resin, designed to crose and fi x concrete surfaces. The system can be used as binder for the production of synthetic screeds for rough bases under coatings and synthetic screeds. Light operation coating compounds MFC Ekopox K compound based on water epoxy resin dispersion. The compound is recommended to be used as fi nal surface treatment on concrete fl oors and industrial self-levelling layers from the MFC Level 300 series. Special compounds MFC Ekopox K solvent free compound based on low-viscosity epoxy resin. The compound is designed for repairing joints and cracks in anhydrite screed and self-levelling compounds and can also be used to repair uncompacted surfaces and injections of caverns. Surface treatment for filled concrete floors Surface treatment with levelling layer for use in reconstructing industrial floors Levelling of industrial floors under coating MFC impregnation MFC Cobet MFC impregnation MFC Final , 430 MFC penetration MFC Final 420, 440 MFC penetration synthetic levelling layer MFC Final 420, 440

10 Use of dry construction mixtures MFC MFC materials Thickness of the layer min. max. (mm) Consumption layer 1 mm (kg/m 2 ) Ready to walk (hours) Base recommended for application concrete porous concrete wood stone PVC steel flooring covers Surface treatment coats coating layers without surface treatment MFC coats DRY-SHAKES, SCREEDS MFC Cobet ,6 24 MFC Cobet ,6 24 MFC Cobet ,6 24 MFC Cobet ,6 24 REPAIR SCREEDS AND MORTARS MFC Sanfix ,7 Level 300 MFC Sanfix ,7 Level 300 MFC Sanfix ,7 Level 300, Final 400 SELF-LEVELLING SCREEDS MFC Level ,7 1 3 MFC Level ,7 1 3 MFC Level ,7 1 3 MFC Level ,7 1 3 MFC Level ,7 1 3 MFC Level ,7 1 3 MFC Level ,7 1 3 Level 330, 320 Level 330, 320 SELF-LEVELLING INDUSTRIAL SCREEDS MFC Final ,7 3 5 MFC Final ,7 3 5 MFC Final ,7 3 5 MFC Final ,7 3 5 MFC Final ,8 1 3 MFC Final ,9 3 5 Final MFC Final ,8 1 3 Final 430

11

12 Your authorized dealer Olbrachtova Tišnov Czech Republic Tel.: Fax: ver. 04/2014an