Multi-point door hardware and accessories

Transcription

1 Multi-point Door Hardware Multi-point door hardware and accessories Edition 07 / C.

2 Contents Multi-point door hardware Contents....2 Multi-point Product Information...3 Multi-point Door Locks, New Breed The Wolverine Door Lock System....4 The Wolverine Inactive Door Lock System....5 The Eagle Door Lock System.... The Hawk Door Lock System....7 The Panther Door Lock System.... The Unicorn Door Lock System....9 Multi-point Door Locks, Europa The Cremona Door Lock System....0 The Cremona Inactive Door Lock System... The Rhino Door Lock System....2 The Rhino-shoot Door Lock System....3 The Tripact Door Lock System....4 The Tripact-shoot Door Lock System....5 The Europa R2 Door Lock System.... The Europa Inactive Door Lock System....7 The Monolock Door Lock System.... Multi-point Door Lock Accessories Operable Sidelight Hardware....9 Astragal Mortise Lock.... Manual Flush Bolt, Mill-In....2 Manual Flush Bolt, Route-In.... Dummy Plates Spindles Lock Cylinder and Locking Components Construction key Multi-point Door Strike Plates Latch/Deadbolt Strike Plates....2 Strike Plates Decorative Door Trim for Multi-point Door Hardware The Bellissimo Collection - Trim Series The Bellissimo Collection - Trim Series Decorative Levers Technical Information Strike Plate Handing, Latch/Deadbolt....3 Multi-point Hardware Installation Instructions Installation Instructions: Cremona, Cremona R2, and Wolverine Installation Instructions: Tripact, Rhino, Eagle and Hawk MLDH milling details Metric/Inch Conversion Table....3 Troubleshooting G-U multi-point door lock systems Function check for G-U multi-point door lock systems Edition 07 / C

3 Multi-point Product Information Multi-point door locks: New Breed and EUROPA for wood doors Application Swing patio doors Balcony/Terrace doors French doors Entry doors Designs Multi-point Door Locks New Breed All New Breed Multi-Point Door Locks have identical construction and function features. The latch is operated by rotating the handle down. Non-handed latch, easily reversible Locking by U.S. cylinder system. The curved corners of the lock case ease the milling of wood doors. Backset is 45 mm. The locking mechanism is located above the lever handle. Heavy duty mortise construction with reinforced lever return spring system Multi-point Door Locks Europa All Europa Multi-point Door Locks have identical construction and function features. The rolling pins (lock pins) or bolts are engaged by lifting the door handle and then locked by turning the key or thumb-turn. The latch is operated by rotating the handle down. Reversible latch the door locks can be used for left hand and right hand hinged doors. The curved corners of the lock case ease the milling of wood doors. The locking mechanism is located below the lever handle. Locking by U.S. cylinder system. Standard Colors Yellow Silver Black White Stainless Steel Single parts are galvanized and yellow dichromated. Single parts galvanized and Silver FerGuard (patented finish). (Not available for all door locks) Upon Request Single parts galvanized and Silver FerGuard, visible surfaces with black powdercoat. Single parts galvanized and Silver FerGuard, visible surfaces with white powdercoat. Single parts galvanized and Silver FerGuard, visible surfaces with stainless steel. (Not available for all door locks) Materials, protection against rust The fitting parts are made of high quality steel, zinc die-casting and aluminum alloys; galvanized and Silver FerGuard, aluminum parts anodized. Article Numbers Example Article No Part number Size - - -L- DIN left hand - - -R- DIN right hand Usable on both sides * Finish Edition 07 / C.3

4 Multi-point Door Locks, New Breed The Wolverine Door Lock System The Wolverine 3-point locking system features double reinforced shoot bolts, top and bottom for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: (25 mm) throw on deadbolt 3-point, height adjustable, locking system Double reinforced shoot bolts, top and bottom, deadbolt and latch US design with deadbolt located above lever Extensions are available for taller doors Lever controlled engaging and releasing of shoot bolts and latch Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish and 300 series stainless steel Same hardware groove detail throughout our entire door lock program (router bits available) B Item Description Article No. Qty. A US Wolverine 3-point door lock system 45mm backset - Standard finish mm backset - Stainless B Reversing gear G Reversing gear Stainless C [] Extension 500mm w/o lock point G A/R Opt: Extension 500mm Stainless B A/R D Brass sleeve, 0mm I.D OR D2 Brass sleeve, 2mm I.D Screws, Hardware installation -U * A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. [] = for doors > Finish: = silver FerGuard, = Stainless steel (300 series) Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square C A D 9 2 Locking Unlocking D2.4 Edition 07 / C

5 Multi-point Door Locks, New Breed The Wolverine Inactive Door Lock System The Wolverine Inactive 2-point locking system features double reinforced shoot bolts, top and bottom for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 2-point, height adjustable, locking system Double reinforced steel shoot bolts, top and bottom US design with deadbolt located above lever Extensions are available for taller doors Lever controlled engaging and releasing of shoot bolts Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish Same hardware groove detail throughout our entire door lock program (router bits available) 0 B Item Description Article No. Qty. A US Wolverine 2-point door lock system 45mm backset - standard finish mm backset - Stainless B Reversing gear G Reversing gear Stainless C [] Extension 500mm w/o lock point G A/R Extension 500mm Stainless B A/R D Brass sleeve, 0mm I.D OR D2 Brass sleeve, 2mm I.D Screws, Hardware installation -U A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. [] for doors > Finish: = silver FerGuard, = Stainless steel (300 series) C Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A D 9 2 Locking Unlocking D2 Edition 07 / C.5

6 Multi-point Door Locks, New Breed The Eagle Door Lock System The Eagle 3-point locking system features automatic locking with (25 mm) deadbolt and two additional 3/4 ( mm) latches which become deadbolts for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: (25 mm) throw on deadbolt Two beveled latches constructed of hardened steel US design with deadbolt located above lever Lever controlled releasing of beveled latches and center latch Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish or stainless steel for increased corrosion resistance Same hardware groove detail throughout our entire door lock program (router bits available) Item Description Article No. Qty. A US Eagle 3-point door lock system For tall doors (refer to dimension A ) 45mm backset - standard finish mm backset - stainless (959mm) R- B For 0 tall doors (refer to dimension B ) 45mm backset - standard finish mm backset - stainless (23mm) R- Central strike plate (for latch_deadbolt) Refer to strike catalog page Strikes for additional latches (upper_lower) 2 Refer to strike catalog page Screws, Hardware installation (bag of ) -U * A/R Optional stainless steel groove fillers 50.mm length mm length mm length Refer to appropiate catalog page for strikes, spindles, locks, etc. Finish: = silver FerGuard, = Stainless steel (400 series) Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A = 20 and 959 (Stainless Finish) B = 2439 (Std. Finish) and 23 (Stainless Finish) A = 3 (070) B = 550 (477) A = 793 B = A 42 Locking Unlocking. Edition 07 / C

7 Multi-point Door Locks, New Breed The Hawk Door Lock System The Hawk 3-point locking system features semi-automatic locking with (25 mm) deadbolt and two additional 3/4 ( mm) latches which become deadbolts when lever or thumb-turn is operated for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: (25 mm) throw on deadbolt Two beveled latches constructed of hardened steel US design with deadbolt located above lever 25/32 (45 mm) backset Lever controlled engaging and releasing of beveled latches and center latch Locking and deadbolt engagement by US-Cylinder system with a 90 0 turn of key or thumb-turn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish or stainless steel for increased corrosion resistance Same hardware groove detail throughout our entire door lock program (router bits available) Item Description Article No. Qty. A US Hawk 3-point door lock system For tall doors (refer to dimension A ) 45mm backset - standard finish mm backset - stainless (20mm) R- B For 0 tall doors (refer to dimension B ) 45mm backset - standard finish mm backset - stainless (23mm) R- Central strike plate (for latch_deadbolt) Refer to strike catalog page Strikes for additional latches (upper_lower) 2 Refer to strike catalog page Screws, Hardware installation (bag of ) -U * A/R Optional stainless steel groove fillers 50.mm length mm length mm length Refer to appropiate catalog page for strikes, spindles, locks, etc. Finish: = silver FerGuard, = Stainless steel (400 series) Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A = 20 B = 2439 (Std. Finish) and 23 (Stainless Finish) A = 3 B = 550 A = 793 B = A 42 Locking Unlocking Edition 07 / C.7

8 Multi-point Door Locks, New Breed The Panther Door Lock System The Panther 3-point locking system features heavy duty hook bolts for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: (25 mm) throw on deadbolt Two hook bolts, deadbolt and latch US design with deadbolt located above lever Extension with additional hook-bolt is available for taller doors Lever controlled engaging and releasing of shoot bolts and latch Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish Same hardware groove detail throughout our entire door lock program (router bits available) Item Description Article No. Qty. A US Panther 3-point door lock system 45mm backset - standard finish mm backset - Stainless B [] Extension 750mm G Extension 750mm - Stainless B Central strike plate (for latch_deadbolt) Refer to strike catalog page Strikes for additional latches (upper_lower) 2 Refer to strike catalog page Screws, Hardware installation B 45 (bag of ) -U * A/R Refer to appropiate catalog page for strikes, spindles, locks, etc. [] = for doors > Finish: = silver FerGuard, = Stainless steel (300 series) Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A Locking Unlocking. Edition 07 / C

9 Multi-point Door Locks, New Breed The Unicorn Door Lock System The Unicorn locking system consists of the same reliable features you ve come to expect from G-U. This product is ideal for exterior and interior door applications. The routing and mortising dimensions are the same as our multi-point locking systems. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: (25 mm) throw on deadbolt US design with deadbolt located above lever Lever controlled releasing of deadbolt and latch Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish Same hardware groove detail throughout our entire door lock program (router bits available) 45 9 Item Description Article No. Qty. A US Unicorn door lock system 45mm backset - standard finish Central strike plate (for latch_deadbolt) Refer to strike catalog page Screws, Hardware installation (bag of ) -U * A/R Refer to appropiate catalog page for strikes, spindles, locks, etc. Finish: = silver FerGuard Technical Specifications: Faceplate = mm wide Spindle size = mm on the square Locking Unlocking Edition 07 / C.9

10 Multi-point Door Locks, Europa The Cremona Door Lock System The Cremona 3-point locking system features shoot bolts, top and bottom for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 3-point, height adjustable, locking system Shoot bolts, top and bottom, deadbolt and latch Extensions are available for taller doors Lever controlled engaging and releasing of shoot bolts deadbolt and latch Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish, black matte lacquer finish or 400 series stainless steel for increased corrosion resistance Same hardware groove detail throughout our entire door lock program (router bits available) B Item Description Article No. Qty. A Cremona door lock, 50mm backset * B Reversing gear G * C Extension 500mm w/o lock point G * A/R Opt: Extension 500mm w/lock point G * A/R D Brass sleeve, 0mm I.D OR D2 Brass sleeve, 2mm I.D Screws, Hardware installation -U * A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. * Represents finish = Silver FerGuard = Black matte lacquer = Stainless Steel 400 series Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A X C D 2 Unlocking Locking D2.0 Edition 07 / C

11 Multi-point Door Locks, Europa The Cremona Inactive Door Lock System The Cremona Inactive 2-point locking system features shoot bolts, top and bottom for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 2-point, height adjustable, locking system Shoot bolts, top and bottom Extensions are available for taller doors Lever controlled engaging and releasing of shoot bolts Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish Same hardware groove detail throughout our entire door lock program (router bits available) 0 B Item Description Article No. Qty. A Cremona door lock, 50mm backset B Reversing gear G C Extension 500mm w/o lock point G A/R Opt: Extension 500mm w/lock point G A/R D Brass sleeve, 0mm I.D OR D2 Brass sleeve, 2mm I.D Screws, Hardware installation -U A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. Finish = Silver FerGuard C 95 Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A X D 2 Unlocking Locking D2 Edition 07 / C.

12 Multi-point Door Locks, Europa The Rhino Door Lock System The Rhino 3-point locking system features tempered steel horns which lock in an upward direction providing maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 3-point, height adjustable, locking system Two steel horn, deadbolt and latch (25 mm) steel horns lock in an upward direction providing an anti-lift device Extension with additional horn-bolt is available for taller doors Lever controlled engaging and releasing of steel horns, deadbolt and latch Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Security may be further extended with the addition of top and bottom shoot bolts Heavy duty mortise construction with reinforced lever return spring system Available in standard finish Same hardware groove detail throughout our entire door lock program (router bits available) 50 C B Item Description Article No. Qty. A Rhino door lock, 35mm backset B Extension Rhino w/ lock point G A/R Opt: Extension 500mm w/o lock point G A/R Optional C Reversing gear (top shoot) G D Bottom shoot G E Brass sleeve, 2mm I.D Screws, Hardware installation -U A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. Finish = Silver FerGuard Technical Specifications: Handle height = adjustable Faceplate = mm wide Spindle size = mm on the square Rhino door lock height dimensions Dim A w/o shoots w/shoots Dim B w/o shoots w/shoots A 930 B A 0 25 X D Unlocking Locking E Edition 07 / C

13 Multi-point Door Locks, Europa The Rhino-shoot Door Lock System The Rhino-shoot 5-point locking system features shoot bolts, top and bottom, two tempered steel horns which lock in an upward direction providing maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 5-point, height adjustable, locking system Top and bottom shoot bolts, two steel horns, deadbolt and latch. Extensions with an additional steel horn is available for taller doors. Lever controlled engaging and releasing of all locking points Locking by US-Cylinder system with a 90 0 turn of key or thumbturn. Non-handed, latch easily reversible. Heavy duty mortise construction with reinforced lever return spring system Available in 400 series stainless steel faceplate for increased corrosion resistance and appearance. Same hardware groove detail throughout our entire door bolt program (router bits available). Item Description Article No. Qty. A Rhino door lock, 35mm backset B Reversing gear G C Extension Rhino w/ lock point G A/R Opt: Extension 500mm w/o lock point G A/R D Brass sleeve, 0mm I.D OR D2 Brass sleeve, 2mm I.D Screws, Hardware installation -U A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. Finish = Stainless Steel 400 series B C Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A 25 X D Unlocking Locking D2 Edition 07 / C.3

14 Multi-point Door Locks, Europa The Tripact Door Lock System The Tripact 3-point locking system features heavy duty hook bolts for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 3-point, height adjustable, locking system Two hook bolts, deadbolt and latch Extension with additional hook-bolt is available for taller doors Lever controlled engaging and releasing of hook-bolts, deadbolt and latch Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard or black matte finish Same hardware groove detail throughout our entire door lock program (router bits available) B Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square Item Description Article No. Qty. A Tripact door lock, 50mm backset * B Extension 500mm w/o lock point G * A/R Opt: Extension 750mm w/lock point * A/R Screws, Hardware installation -U * A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. 0 * Represents finish = Silver FerGuard = Black matte lacquer 47 A X Unlocking Locking.4 Edition 07 / C

15 Multi-point Door Locks, Europa The Tripact-shoot Door Lock System The Tripact-shoot 5-point locking system features shoot bolts, top and bottom, and two heavy duty hook bolts for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 5-point, height adjustable, locking system Shoot bolts, top and bottom, two heavy duty hook bolts, deadbolt and latch Extensions with or without additional hook are available for taller doors Lever controlled engaging and releasing of all locking points Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish or black matte lacquer finish Same hardware groove detail throughout our entire door lock program (router bits available) Item Description Article No. Qty. A Tripact-shoot door lock, 50mm * B Reversing gear G * C Extension 500mm w/o lock point G * A/R Opt: Extension 750mm w/lock point * A/R D Brass sleeve, 0mm I.D OR D2 Brass sleeve, 2mm I.D Screws, Hardware installation -U * A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. * Represents finish = Silver FerGuard = Black matte lacquer B Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A X D Unlocking Locking D2 Edition 07 / C.5

16 Multi-point Door Locks, Europa The Europa R2 Door Lock System The Europa R2 multi-point door lock system, with its 5-point locking system features two adjustable rolling pins, top and bottom shoot, deadbolt, and latch, combines function and design flexibility for any application. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 5-point, height adjustable, locking system Two adjustable rolling pins, shoot bolts top and bottom, deadbolt and latch Extensions with additional rolling pin available for taller doors Lever controlled engaging and releasing of all locking points Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish Same hardware groove detail throughout our entire door lock program (router bits available) B Item Description Article No. Qty. A Europa R2 door lock, 35mm backset B Reversing gear G C Extension 500mm w/o lock point G A/R Opt: Extension 500mm w/lock point G A/R D Bottom shoot G E Brass sleeve, 2mm I.D Screws, Hardware installation -U A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. Finish = Silver FerGuard C Technical Specifications: Handle height = adjustable Faceplate = mm wide Spindle size = mm on the square Rolling Pin = mm A X E D Unlocking Locking 0. Edition 07 / C

17 Multi-point Door Locks, Europa The Europa Inactive Door Lock System The Europa Inactive 2-point locking system features shoot bolts, top and bottom for maximum security and protection against warping of the door panels. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: 2-point, height adjustable, locking system Shoot bolts, top and bottom Extensions are available for taller doors Lever controlled engaging and releasing of shoot bolts Locking by US-Cylinder system with a 90 0 turn of key or thumbturn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish Same hardware groove detail throughout our entire door lock program (router bits available) B Item Description Article No. Qty. A Europa Inact. door lock, 35mm B Reversing gear G C Extension 500mm w/o lock point G A/R D Bottom shoot G E Brass sleeve, 2mm I.D Screws, Hardware installation -U A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc. Finish = Silver FerGuard C Technical Specifications: Handle height = 9 mm (35 ) from bottom of faceplate Faceplate = mm wide Spindle size = mm on the square A X E 250 D Unlocking Locking 0 Edition 07 / C.7

18 Multi-point Door Locks, Europa The Monolock Door Lock System The Monolock system consists of the same reliable features you ve come to expect from G-U. This product is ideal for exterior and interior door applications. The routing and mortising dimensions are the same as our multi-point locking systems. Also featured is our 90 0 locking mechanism that incorporates a standard US cylinder offering a variety of Schlage C keyway systems. Key Features: (25 mm) throw on deadbolt US design with deadbolt located above lever Lever controlled releasing of deadbolt and latch Locking by US-Cylinder system with a 90 0 turn of key or thumb-turn Non-handed, latch easily reversible Heavy duty mortise construction with reinforced lever return spring system Available in standard finish, polished brass or stainless steel for increased corrosion resistance Same hardware groove detail throughout our entire door lock program (router bits available) Item Description Article No. Qty. A US Monolock Door Lock Backset 30mm -UA * Backset 35mm -UA * Backset 40mm -UA * Backset 45mm -UA * Backset 50mm -UA * Backset 55mm -UA * Screws, Hardware installation -U * A/R (bag of ) Refer to appropiate catalog page for strikes, spindles, locks, etc * Represents finish = Silver FerGuard 03 = Polished Brass = Stainless steel Technical Specifications: Faceplate = mm wide Spindle size = mm on the square X Unlocking Locking. Edition 07 / C

19 Multi-point Door Lock Accessories Operable Sidelight Hardware G-U Hardware, Inc. is proud to introduce another innovative product for the entry door market. This new hardware system helps improve the weather seal and security of operable sidelight panels (reference diagram below). Very simple and easy to operate, this system offers a practical alternative to fixed sidelights. Key Features: Multiple locking points for added security Adjustable rolling pins for tighter sealing Utilizes same thumb-turn as the Bellissimo Collection Available in a wide variety of finishes Same hardware groove detail throughout our entire door lock program (router bits available) Qty. Item Description Part Number Order Qty. Operable Sidelight Hardware A Sidelight Gear G B Polished Brass Rosette and Thumb-turn -U C Sidelight Locking Plates 9-U Attachment Screws - Rosette (Not Shown) 9-U Attachment Screws - Sidelight (Not Shown) -U A Note: All units in millimeters ( = 25.4 mm) Drawings not to scale All items are subject to pricing and availability Thumb-turn available in Polished Brass... other finishes available upon special request Contact G-U for additional information For technical information reference MLDH Milling Details Technical Specifications: Faceplate = mm wide Spindle size = 7 mm on the square Sidelights 43 B Operable Sidelight Diagram with sidelight in opened position C Brass Rosette and Thumb-turn Sidelight Locking Plate Edition 07 / C.9

20 Multi-point Door Lock Accessories Astragal Mortise Lock The Astragal Mortise Lock from G-U Hardware, Inc. is an optional means of securing the inactive panel of a double (French) door system. This system is designed for doors between - and 0-0 tall where a flush bolt is desired. The inactive door panel on a double door is secured by flipping the lever 0 0 with your finger which either engages or disengages both the top and bottom shoots. Key Features: For the inactive panel of double entrance doors, patio doors or interior doors. Overall size of flip lever is 250 mm long X mm wide X 32 mm deep Projection of rod is 4 mm top and 4 mm bottom Rod size is ø0 mm (length varies) Non-handed Flip lever body is constructed of steel Rods available in standard finish Flip lever faceplate is available in Stainless Steel E Qty. Item Description Part Number Order Qty. A Astragal Mortise Lock (for doors '-" to 0'-0" tall) K B Bottom Rod (47 /4" long) 9-U C Top Rod (23 3/4" long) 9-U (25 3/4" long) 9-U (27 3/4" long) 9-U (39 3/4" long) 9-U (3 3/4" long) 9-U D Brass Sleeves 2 mm I.D. (Solid Brass, Unfinished) E Rod Guides (Stainless Steel) 9-U Attachment Screws (Rod Guide) (4.2 x ) or (# x 3/4") Stainless Steel E Attachment Screws (Mortise Lock) (5 x 9 mm) Stainless Steel 9-U Note: All units in millimeters ( = 25.4 mm) Drawings not to scale All items are subject to pricing and availability A (Retracted Dim.) C 5 (Extended Dim.) 2 2 B E D. Edition 07 / C

21 Multi-point Door Lock Accessories Manual Flush Bolt, Mill-In The Manual Flush Bolt from G-U Hardware, Inc. is an optional means of securing the inactive panel of a double or French door system. Simply flip the spring loaded lever 0 0 with your finger to engage or to disengage the shoot. Key Features: For the inactive panel of double entrance doors, patio doors, or interior doors Overall size is 250 mm long x mm wide x mm deep Projection of shoot is mm Shoot size is.5 mm wide x 2.7 mm thick Non-handed Body constructed of steel Available in standard finish Qty. Item Description Part Number Order Qty. 2 A Manual Flush Bolt Mill-in version (Standard Finish) A * 2 Brass Sleeves (Select one size only) B 0 mm I.D. (Solid Brass, Unfinished) or B2 2 mm I.D. (Solid Brass, Unfinished) Attachment Screws (4.2x30) Standard Finish (/Bag) -U Note: All units in millimeters ( = 25.4 mm) Drawings not to scale All items are subject to pricing and availability For technical information reference MLDH Milling Details Technical Specifications: Width = mm wide Overall Length = 250 mm Finish = Standard 4 B B2 T Astragal applied to inactive sash Inactive Sash Active Sash Milling Requirements Edition 07 / C.2

22 Multi-point Door Lock Accessories Manual Flush Bolt, Route-In The Manual Flush Bolt from G-U Hardware, Inc. is an optional means of securing the inactive panel of a double or French door system. The ease of operation and simple installation of this attractive flush bolt has once again set us apart from the rest. Whether you prefer the polished look of brass or corrosion resistant stainless steel finish, you can rest assured that you will find comfort knowing your door is properly secured. Key Features: Ideal for the inactive panel of double entrance doors, patio doors, or interior doors Stainless steel locking rod Full (25 mm) projection of locking rod Industry standard size Non-handed Body constructed of steel Available in polished brass or in stainless steel finish for increased corrosion resistance Stainless steel locking plate (router bit available) Qty. Item Description Part Number Order Qty. 2 A Manual Flush Bolt Polished Brass -U or Stainless Steel -U (Includes locking plate and attachment screws) B Router Bit (without cutting inserts) 9-U Replacement Inserts (for router bit) 73N Stainless Steel Rod Note: All units in millimeters ( = 25.4 mm) Drawings not to scale All items are subject to pricing and availability For technical information reference MLDH Milling Details Technical Specifications: Faceplate = 3/4 wide x long Rod is /4 dia. X long Rod constructed of 304 stainless steel 52 B A 2 - # x /4 Screws Required Router Bit 2.7 Locking Plate Stainless Steel Only 2 - # x 3/4 Stainless Steel Screws Required. Edition 07 / C

23 Multi-point Door Lock Accessories Dummy Plates The Dummy Plates offer several options for mounting escutcheon plates and levers to doors. The primary use of the dummy plate is to provide a balanced aesthetic appearance between the decorative trim on the inactive panel and the decorative trim on the active panel on a set of double (French) doors. There are several hardware options for the inactive panel. In the case where a Cremona 2- point, lever operated system is not desired, the dummy plate offers a method to attach the escutcheon plates and lever to the inactive panel in such a way that it does not have any function but rather balances the appearance. The dummy plate is surface mounted onto the door stile. The dummy plate is then covered by the decorative escutcheon plates and levers. Qty. Item Description Part Number Order Qty. 2 E Full Dummy Plate (w/o spindle) 9-U Attachment Screws (4.2x30) Standard Finish (/Bag) -U Reference trim section for escutcheon plates and levers. A Note: All units in millimeters ( = 25.4mm) Drawings not to scale All items are subject to pricing and availability For technical information reference MLDH Milling Details Technical Specifications: Spindle size = mm on the square Spindles The Spindle is used to connect the interior and exterior lever. Multiple lengths are offered to accomodate various door thicknesses. Qty. Item Description Door Thickness Dim. "A" Part Number Order Qty. A Spindle, Full Split 2 mm 9-U Spindle, Full Split 90 mm 9-U Spindle, Full Split up to.75 inches 00 mm 9-U Spindle, Full Split 05 mm 9-U Spindle, Full Split up to 2.00 inches 0 mm 9-U Spindle, Full Split up to 2.50 inches mm 9-U Spindle, Full Split up to 3.00 inches 30 mm 9-U Spindle, Full Split 45 mm 9-U Reference trim section for escutcheon plates and levers. A Edition 07 / C.23

24 Multi-point Door Lock Accessories Lock Cylinder and Locking Components The U.S. Cylinder, used with the U.S. Multipoint Doorbolt system, comes with a standard Schlage C keyway for ease of keying alike to existing door cylinders and a tailpiece on the opposite end to connect to an interior thumbturn. The cylinder body is constructed of brass and has a brushed chrome finish on the face. A tailpiece conversion kit is also available for those doors greater than -3/4 to reach the thumbturn on the opposite side. This cylinder is also stocked in eight () different keyways for those with specific keyway needs. Qty. Item Description Part Number Order Qty. A US Cylinder -U U U U U U U U Reference trim section for escutcheon plates and levers. The US Cylinder tailpiece connects the locking cylinder to the mortise case and to the thumb-turn (inside); thereby, allowing the locking feature of the mortise case to be operational. An extended length is available for doors greater than.75 up to Qty. Item Description Door Thickness Dim. "A" Part Number Order Qty. A Tailpiece Conversion Kit Up to.75" 37 mm -U Tailpiece Conversion Kit Up to 2.75" 2 mm -U Reference trim section for escutcheon plates and levers. A The Thumb-turn Tailpiece connects the thumb-turn to the mortise case when a key cylinder is not required; thereby, allowing the locking feature of the mortise case to be operational. An extended length is available for doors requiring the multi-point door lock to be offset. Qty. Item Description Door Thickness Dim. "A" Part Number Order Qty. A Tailpiece Half Spindle Up to 3.00" 4 mm 9-U Tailpiece Half Spindle Offset Applications 72 mm 9-U Reference trim section for escutcheon plates and levers. A.24 Edition 07 / C

25 Multi-point Door Lock Accessories Construction key The U.S. construction key is now available for those who prefer to install the decorative hardware trim and lever sets on doors after the construction has been completed. Installing the escutcheon plates and levers in the final stage of construction prevents the decorative trim from becoming scratched or damaged. The construction key has been designed to accommodate multi-point door hardware (mm square), tilt-turn hardware (7mm square) and lift-slide hardware (0mm square). 7mm square (Tilt-turn) mm square (MLDH) 0mm square (Lift-slide) 9-U mm square spindle hub US cylinder slot Cylinder tab Edition 07 / C.25

26 Multi-point Door Strike Plates Latch/Deadbolt Strike Plates Qty. Description Part Number Order Qty. Strike Plates for 3/4" thick door Square ends with straight lip E * Round ends with straight lip E * Round ends with radial lip (Handed) 9-U333-SL-L/R-* Round ends with radial lip (Handed) 9-U L/R-* Strike Plates for 2 /4" thick door Square ends with straight lip 9-U3339-XL-0-* Square ends with straight lip (Solid Brass) Round ends with straight lip 9-U333-XL-0-** Round ends with radial lip (Handed) 9-U333-XR-L/R-* 3 Screw, #7 x 5/" Attachment screws (not shown) 9-U * Our Latch/Deadbolt Strike Plate Program offers a variety of styles and finishes for doors of varying thickness. Each strike plate can be used with any multi-point doorlock system from G-U. A variety of strike designs allows for greater flexibility to meet the customers needs. Some strikes have an extended lip for those doors 2 /4 thick. Some strikes have a radial lip for smoother operation while others have a straight lip and are non-handed to accommodate a wider range of door sashes and frames. Most strike plates are constructed of steel with a plated finish to match the color of your escutcheon plates and levers. To further meet our customer s requirements, we provide latch/deadbolt strikes with square ends for manual installation or strikes with rounded ends for machining the strikes into place. Nomenclature: 25 R = Right Hand L = Left Hand XL = Extended Lip XR = Extended Lip with Radius SL = Shorter Radial Lip * Represents finish 0 = Satin Chrome 3 = Standard Finish 02 = Polished Chrome = Stainless Steel 03 = Polished Brass 04 = Antique Brass 0 = Pewter 07 = White Powder Coat 0 = Black Powder Coat 2 = Dark Bronze Powder Coat E * Thickness = 2 mm 2 9-U3339-XL-0-* Thickness = 2 mm Thickness = 2 mm E * Thickness = 2 mm 9-U333-XR-LorR-* Thickness = 2 mm 9-U333-XL-0-* Thickness = 2 mm 9-U333-SL-LorR-* Thickness = 2 mm 9-U LorR-* Thickness = 2.3 mm.2 Edition 07 / C

27 Multi-point Door Strike Plates Strike Plates The Multi-Point Door Strike Plates shown below work with a variety of multi-point door locks from G-U. These strike plates are designed to be used with, but are not limited to the Tripact, the Eagle, the Hawk, and the Panther multi-point door locks. Most strike plates are constructed of steel with a plated finish to match the color of your escutcheon plates and levers. Make sure the number of strike plates corresponds to the number of locking points when ordering. Qty. Description Part Number Order Qty. 2+ Strike Plates for 3/4" thick door Square ends without lip E * Round ends without lip E * Square ends with straight lip 0-057B-00-0-* Round ends with straight lip 0-05B-00-0-* Round ends with radial lip (Non-handed) 9-U * 2+ Strike Plates for 2 /4" thick door Square ends with straight lip 9-U57B-XL-0-* Square ends with straight lip (Solid Brass) Screw, #7 x 5/" Attachment screws (not shown) 9-U * 2.5 * Represents finish 0 = Satin Chrome 02 = Polished Chrome 03 = Polished Brass 04 = Antique Brass 0 = Pewter 07 = White Powder Coat 0 = Black Powder Coat 2 = Dark Bronze Powder Coat 3 = Standard Finish = Stainless Steel E * Thickness = 2 mm 0-057B-00-0-* Thickness = 2 mm 2.5 9U57B-XL-0-* Thickness = 2 mm Polished Solid Brass Only Thickness = 2 mm E * Thickness = 2 mm 0-5B-00-0-* Thickness = 2 mm 9-U * Thickness = 2.3 mm Edition 07 / C.27

28 Decorative Door Trim for Multi-point Door Hardware The Bellissimo Collection - Trim Series 400 The Bellissimo Collection of door trim features high quality forged (not cast) escutcheon plates and levers constructed of solid brass. For keyed entries, G-U provides US cylinders with a standard Schlage C keyway for ease of keying alike to existing door cylinders. Also provided is a 90 thumb-turn for locking and unlocking. This special thumb-turn allows the comfort of knowing your door is securely locked by visual inspection Key features: Schlage C keyway for keying all cylinders alike 90 locking with thumb-turn Solid brass escutcheon plates forged for higher strength Variety of finishes Escutcheon plates are interchangeable due to identical attachment holes Surface protected finish Stainless steel set screw on levers to attach spindle All systems may be converted to dummy sets US Trim Series 400 (Sold in pairs) A Key Outside/Thumb-turn Inside 9-U ** B Thumb-turn Inside Only 9-U ** C Blind (No key, no thumb-turn) 9-U ** Levers (Refer to Levers) Attachment Screw s (Not Show n) According to Door Thickness Up to 3/4" (Screw Length = 50 mm) 9-U ** Up to 2" (Screw Length = 55 mm) 9-U ** Up to 2 /4" (Screw Length = 5 mm) 9-U ** Up to 2 /2" (Screw Length = 70 mm) 9-U ** Up to 3" (Screw Length = 0 mm) 9-U **? Full Spindle (Not Show n) According to Door Thickness Up to 3/4" (Spindle Length = 00 mm) 9-U Up to 2" (Spindle Length = 0 mm) 9-U Up to 2 /2" (Spindle Length = mm) 9-U Up to 3" (Spindle Length = 30 mm) 9-U X X US Cylinder w ith Schlage Keyw ay (For use w ith key outside trim only) -U02-0*-0-0 X X Half Spindle Tailpiece (Used w ith thumb-turn inside only trim) 9-U X X Tailpiece Conversion Kit (For use w ith key outside trim only and doors > 3/4" thick) -U X X 2 Full Dum m y Plates (For use w ith lever only trim) (Refer to Acc) A B 5 Version 492 Version 44 Note: Detailed dimensional drawings are available for all plates upon special request All items are subject to pricing and availability * Eight different Schlage keyways possible (i.e. -U thru -U ). If multiple keyways are required please specify quantities and keyway numbers foreach. ** Represents finish (0=Satin Chrome, 02=Polished Chrome, 03=Polished Brass, 04=Antique Brass, 0=Pewter, 07=White powder coat, 0= Black powder coat, 2 = Dark Bronze powder coat) C Version 40.2 Edition 07 / C

29 Decorative Door Trim for Multi-point Door Hardware The Bellissimo Collection - Trim Series 500 The Bellissimo Collection of door trim features high quality forged (not cast) escutcheon plates and levers constructed of solid brass. For keyed entries, G-U provides US cylinders with a standard Schlage C keyway for ease of keying alike to existing door cylinders. Also provided is a 90 thumb-turn for locking and unlocking. This special thumb-turn allows the comfort of knowing your door is securely locked by visual inspection. Key features: Schlage C keyway for keying all cylinders alike 90 locking with thumb-turn Solid brass escutcheon plates forged for higher strength Variety of finishes Escutcheon plates are interchangeable due to identical attachment holes Surface protected finish Stainless steel set screw on levers to attach spindle All systems may be converted to dummy sets US Trim Series 500 (Sold in pairs) A Key Outside/Thumb-turn Inside 9-U ** B Thumb-turn Inside Only 9-U ** C Blind (No key, no thumb-turn) 9-U ** Levers (Refer to Levers) Attachm ent Screw s (Not Show n) According to Door Thickness Up to 3/4" (Screw Length = 50 mm) 9-U ** Up to 2" (Screw Length = 55 mm) 9-U ** Up to 2 /4" (Screw Length = 5 mm) 9-U ** Up to 2 /2" (Screw Length = 70 mm) 9-U ** Up to 3" (Screw Length = 0 mm) 9-U **? Full Spindle (Not Show n) According to Door Thickness Up to 3/4" (Spindle Length = 00 mm) 9-U Up to 2" (Spindle Length = 0 mm) 9-U Up to 2 /2" (Spindle Length = mm) 9-U Up to 3" (Spindle Length = 30 mm) 9-U X X US Cylinde r w ith Schlage Ke yw ay (For use w ith key outside trim only) -U02-0*-0-0 X X Half Spindle Tailpiece (Used w ith thumb-turn inside only trim) 9-U X X Tailpiece Conversion Kit (For use w ith key outside trim only and doors > 3/4" thick) -U X X 2 Full Dum m y Plates (For use w ith lever only trim) (Refer to Acc) A B Version 592 Version 54 Note: Detailed dimensional drawings are available for all plates upon special request All items are subject to pricing and availability * Eight different Schlage keyways possible (i.e. -U thru -U ). If multiple keyways are required please specify quantities and keyway numbers foreach. ** Represents finish (0=Satin Chrome, 02=Polished Chrome, 03=Polished Brass, 04=Antique Brass, 0=Pewter, 07=White powder coat, 0= Black powder coat, 2 = Dark Bronze powder coat) C Version 50 Edition 07 / C.29

30 Decorative Door Trim for Multi-point Door Hardware Decorative Levers All levers are constructed of solid brass with a variety of finishes to satisfy even the most demanding customer. For more information about these levers, please contact your local distributor or G-U Hardware, Inc. Qty. Description Part Number Order Qty. 2 The Bellissimo Collection Lever Milan (Non-handed) 9-U ** Lever Capri (Left Hand) 9-U L-** Lever Capri (Right Hand) 9-U R-** Lever Florence (Non-handed) 9-U ** Lever Venice (Left Hand) 9-U L-** Lever Venice (Right Hand) 9-U R-** Lever Roma (Left Hand) 9-U00-00-L-** Lever Roma (Right Hand) 9-U00-00-R-** The Bellissimo Collection - Compatible with Trim Series 400 & 500 Only Lever Milan 5.7 Lever Capri 5.7 Lever Florence Note: All items are subject to pricing and availability ** Represents finish (0=Satin Chrome, 02=Polished Chrome, 03=Polished Brass, 04=Antique Brass, 0=Pewter, 07=White powder coat, 0=Black powder coat, 2=Dark Bronze powder coat) 5 50 Lever Venice 5.7 Lever Roma Edition 07 / C

31 Technical Information Strike Plate Handing, Latch/Deadbolt The perspective for strike plate handing is determined by viewing the door from inside the room looking out. Applicable Part Numbers 9-U333-SL-R-* 9-U333-XR-R-* Applicable Part Numbers 9-U R-* 9-U R-* Applicable Part Numbers 9-U333-SL-L-* 9-U333-XR-L-* Applicable Part Numbers 9-U L-* 9-U L-* LH hinged, Inswing LH hinged, Inswing dbl. door LH hinged, Outswing LH hinged, Outswing dbl. door Primary Primary RH hinged, Outswing RH hinged, Outswing dbl. door RH hinged, Inswing RH hinged, Inswing dbl. door Primary Primary Edition 07 / C.3

32 Technical Information Multi-point Hardware Installation Instructions Tools required: Plunge Router, Chisel, mm (5/"Ø) drill bit, G-U Edge router bit #9-U Hacksaw, Phillips Screwdriver, 9 mm (3/4"Ø) drill bit, G-U Mortise Router Bit #9-U Vise, Square, mm (7/"Ø) drill bit, Door Preparation. Mount G-U router bit #9-U in router and set router bit depth as specified in the Milling Details section. 2. Make one pass over door edge where door lock is to be installed ensuring the router is level and true. 3. After the first pass, check routing to ensure the proper dimensions have been achieved. If dimensions are not accurate, a second pass may be required. 4. Measuring from the bottom of the door, mark handle height center on the door edge. Confirm actual physical door lock handle height with the mark on the door. 5. For Europa door locks, measure from handle height center mark on door edge, down 25 mm (4 5/") towards bottom of the door and mark. Then measure from handle height center mark, up mm (3 7/ ) towards the top of the door and mark. This is your mortise location. Confirm overall mortise location with the actual mortise case.. For New Breed door locks, measure from handle height center mark on the door edge, down 2 mm (3 /4") towards bottom of the door and mark. Then measure from handle height center mark up, 34 mm (5 9/32 ) towards the top of the door and mark. This is your mortise location. Confirm overall mortise location with the actual mortise case. 7. Determine the depth of backset. This should be stamped on the side of the mortise case, for example: 50/92 means the backset = 50 mm and the distance from the center line of handle to center line of the cylinder = 92 mm.. The mortise pocket depth is the backset (X) + mm This is the depth of your mortise router bit. For Example: The mortise pocket depth for a 50 mm backset is 50+=70 mm. 9. Insert G-U mortise router bit #9-U in router and make necessary adjustments according to the mortise pocket depth as mentioned in Step. 0. Make several small incremental passes with router in order to achieve the proper depth and to prevent damage to the door and mortise bit.. Using the multi-point door lock and the appropriate catalog product page locate and mill any additional mortise pockets that may be required for the type of multi-point hardware being installed. 2. Place door lock in door edge groove to ensure proper fit. 3. Verify the face plate of the door lock is level with the edge of the door. 4. Locate the handle height center mark on the door edge and measure from the door edge, across the stile face, towards the door hinge side to locate the backset depth. All other holes for the trim are referenced from this point. Refer to the Milling Details section. Backset C/L Handle height C/L.32 Edition 07 / C