and Measurement Software

Transcription

1 R&S TS8997 and Measurement Software Quick Installation Guide Page 1-07

2 COPYRIGHT Copyright 2015 Rohde & Schwarz GmbH & Co KG. All rights reserved. Portions of the software described in this document copyright of Microsoft Corporation. All rights reserved. Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those agreements. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or any means electronic or mechanical, including photocopying and recording for any purpose other than the purchaser's personal use without the written permission of Rohde & Schwarz. Windows 7, Windows XP, Windows 2000, Windows XP and Windows Installer are trademarks or registered trademarks of Microsoft Corporation in the U.S.A. and other countries. IKey is a registered trademark of Safenet Inc. Dual Core is a registered trademark of INTEL Corporation. Other brands and their products are trademarks or registered trademarks of their respective holders and should be noted as such. ROHDE & SCHWARZ Test and Measurement Division P.O Munich Germany Page 2

3 Copyright Page 3-07

4 Content COPYRIGHT... 2 CONTENT... 4 PREFACE GETTING HELP FOR EMC REGISTRATION OF THE SOFTWARE ONLINE HELP SUPPORT CENTER SEND FEEDBACK EMC32 ON THE INTERNET UPDATE MANAGER TRAINING HARDWARE SETUP AVAILABLE SOFTWARE AND DOCUMENTS ON THE DVD STEP1 - INSTALL NI DAQ AND NI4882 DRIVERS STEP2 - INSTALLING EMC32 AND THE REQUIRED EXTENSIONS STEP2.1 AFTER EMC32 INSTALLATION - DRIVERS UPDATE CHECK STEP2.2 EXAMPLE FOR COPYING PATCHES TO THE EXECUTE FOLDER OF EMC STEP3 - INSTALLING AND CONNECTING OSP PANEL STEP3.1 - IMPORT PATHS TO OSP PANEL STEP4 - CONFIGURING THE EMC32 SOFTWARE STEP PHYSICALLY CONNECTING DEVICES IN THE DEVICE LIST STEP 4.2 CONFIGURING CONNECTED DEVICES OF THE DEVICE LIST OSP-B157 Power Meter TS8997 Vector Generator All other devices Page 4

5 Content Page 5-07

6 Preface The test system TS8997 covers the regulatory test of wireless devices in the 2.4 GHz and 5 GHz band according to the new standards ETSI EN v1.9.1 and ETSI EN v It is controlled by EMC32, the Rohde & Schwarz System Software for EMC measurements on 32 and 64-bit operating systems from Microsoft (Windows XP, Windows Vista, Windows 7). It provides a common user interface for Emission Measurements (EMI), Susceptibility Measurements (EMS) and an Application Interface Macro language for general purpose which is designed to operate like a virtual instrument. It combines the convenience of an intuitive graphical user interface according to the actual Windows standards with the maximum flexibility both for support of measurement devices and for running EMC measurements. This manual should guide and support the user during his first experience with EMC32 software. Therefore the manual provides step by step procedures from software installation and configuration to the first EMC measurement using figures and examples. A detailed description of the installation procedure is provided in the manual "Installation Guide" which is available in printed form and in electronic form on the CD. -07 Page 6

7 Profane Page 7-07

8 Getting Help for TS8997 TS Getting Help for EMC32 Rohde & Schwarz would like to give you the best possible product support. For informing you continuously about news, updates and tips & tricks for EMC32 we recommend that you take the following information into account. 1.1 Registration of the Software Before you start using EMC32 you should register for the EMC32 newsletter service at Rohde & Schwarz website. You will benefit from the registration by receiving information about news and updates of EMC32. Use the following link with a web browser Or start the registration dialog via the help menu item? EMC32 on the Web Newsletter Service. To register in this manner, your computer must be connected to the Internet. 1.2 Online Help The Online Help is available in form of Windows HTML Help both on the CD and after the installation on the hard disk. A shortcut for starting the help is available in the program group EMC32.The help may be started any time via the help menu or by pressing the F1 key (context sensitive) in EMC Support Center This document will guide you through the installation process of EMC32. You will find the necessary instructions for installation, update, the configuration of the software, the start of the program and tips on installation troubleshooting. If you need further assistance for solving problems during the installation please contact your nearest Rohde & Schwarz Support Center: ROHDE & SCHWARZ Customer Support Europe Phone: customersupport@rohde-schwarz.com ROHDE & SCHWARZ Customer Support America Phone: TESTRSA ( ) selection 2 customer.support@rsa.rohde-schwarz.com -07 Page 8

9 Getting Help for TS8997 ROHDE & SCHWARZ Customer Support Asia Phone: ROHDE & SCHWARZ Customer Support China Phone: Send Feedback We are always open to receive any feedback (criticism or suggestion) on EMC32 to improve permanently EMC32. Please use therefore our Send Feedback form. This form you can open via the help menu (? EMC32 on the Web Send Feedback) under the precondition, that your computer is linked to the Internet. Alternatively you can open the form from EMC32 CD-ROM (refer to the Installation Guide for more details on this item). 1.5 EMC32 on the Internet The newest information concerning EMC32 you will find on the web home page of Rohde & Schwarz under There you can find free updates to the newest version of EMC Update Manager The integrated Update Manager will inform you periodically about important information, service packs and updates. The update manager runs automatically in the background but you can also start it manually via the help menu (? Run Update Manager). 1.7 Training Our training center offers intensive training courses for the usage of EMC32 software. Course schedules are available on the Rohde & Schwarz home page. Page 9-07

10 2 Hardware Setup -07 Page 10

11 3 Available Software and documents on the DVD -> Step1 - Install NIDAQ and ni4882 Drivers -> Step2 - Install EMC32 software and required extensions -> Step3 - Installing and connecting OSP Panel -> Step2.2 If available copy the patch to the Execute folder of EMC32 -> Step3.1 - Import Paths to OSP Panel -> Step4 - Restore the TS8997 backup files Configure the devices in the Device List Note: Step3 is applicable only if not preinstalled. Skip the step3 if it is already installed. Page 11-07

12 4 Step1 - Install NI DAQ and ni4882 Drivers Install the NIDAQ and ni4882_311 software Marked options should be present in the list of Software. Software version of NI-DAQmx. should be at least Page 12

13 5 Step2 - Installing EMC32 and the required extensions Install the EMC32 software from the EMC32_CD_Image Folder by double clicking on the Setup_EMC32_AMS32.3.exe file Page 13-07

14 5.1 Step2.1 After EMC32 installation - Drivers update check Install the required drivers for the TS8997 system. -07 Page 14

15 5.2 Step2.2 Example for copying patches to the Execute folder of EMC32 If new patches are available then copy it as defined. If no patch is available then skip this step. Page 15-07

16 6 Step3 - Installing and connecting OSP Panel Skip this step, if Path configuration is already installed on the OSP 120 Install the software. Click to the Start button of windows to open start menu Open the OSP panel After Opening the OSP panel, connect the OSP panel physically with the OSP120 via an appropriate IP address. -07 Page 16

17 6.1 Step3.1 - Import Paths to OSP Panel paths_osp_b157_new.zip Unzip the OSP path in some folder Following paths should be present in the folder After connecting the OSP120 physically, go to Import Paths in order to import the OSP paths from the paths_osp_b157_new folder Page 17-07

18 Select all the paths and press OK. All paths will be imported in the OSP panel and can be checked via Switch Path option in the Path folder of OSP panel. Here all paths must be shown, if not then import again. -07 Page 18

19 7 Step4 - Configuring the EMC32 Software For the first configuration of your system use TS8997_EMC32_Vx_xx_Backup_full_Macro_y_yy_yy.zip (x_xx represents EMC32 version e.g 9_22, y_yy_yy represents matching macro version e.g ) If you only want to update the API macros use TS8997_EMC32_Vx_xx_Backup_Macro_only_y_yy_yy.zip (x_xx represents EMC32 version e.g 9_22, y_yy_yy represents matching macro version e.g ) The actual version of the files described above can be found on the product page or R&S TS For the macro only backup the file should be unziped and used for replacing the macros in System/Test Templates/Api Macro For the full backup go to Backup/Restore and restore the backup. Page 19-07

20 If you have downloaded the Backup files from the Website, you have to use the use password option. If you want to restore the macros only, you have to uncheck the configuration files option. Then Press Start Restore button to restore the full TS8997 backup files. If the TS8997 backup is restored correctly, the following devices should be available: 7.1 Step Physically connecting devices in the Device List Paths will imported automatically once the paths are selected in the OSP panel (as mentioned before) -07 Page 20

21 7.2 Step 4.2 Configuring connected devices of the Device List OSP-B157 Power Meter For the OSP-B157 Power Meter configuration in the device list, the ident number of the connected OSP-B157 is needed. The ident number can be found on the back of the module Page 21-07

22 7.2.2 TS8997 Vector Generator For all DFS tests, the vector generator is used to generate the neccessary radar pulse signals. Radar pulse signals are stored as arbitrary waveform files on the internal harddisk of the vector generator. Since Version 9.22 the waveform files are installed on the PC together with the EMC32 Software. For the very first time (or any subsequent updates) it is absolutely necessary to install/copy the waveform files to the vector generator. It is possible to do this using the device settings dialog of the installed vector generator. Precondition: Connected vector generator is switched to pysical and options K6 or K350 are available on the device. Click the button Upload TS8997 Waveform files and follow the progress. Unzip and transfer the files to the device will take several minutes. Wait until the message Transfer completed appears below then progressbar. -07 Page 22

23 7.2.3 All other devices Other devices shall be connected accordingly. Page 23-07

24 TS8997 system is now ready for the Calibration -07 Page 24