Hot water storage heaters and boiling water heaters

Transcription

1 Hot water storage heaters and boiling water heaters

2 Decentralised storage heaters provide conventional hot water supply. They store the hot water in a heat-insulated tank as close as possible to the point-of-use. They provide a limited amount of mixed water without long wait times. After dispensing the water, the storage tank automatically ﬁlls up again and heats the water to the set temperature. The size of the storage heater can be selected as required: e. g. small storage heaters are sufficient for single points-of-use (wash basins or sinks). The large wall-mounted storage heaters can centrally supply hot water for several points-of-use in an entire apartment. From 5 to 120 litres. Hot water storage heaters Good insulation is a must! High-quality insulation is necessary to keep heat losses during hot water storage at a minimum. Energy saver settings at the temperature control assist in limiting the energy consumption. Since storage heaters take a while to heat the water, they can be operated with comparatively low power ratings. 2 < Storage heater catalogue Storage heater catalogue > 3

3 Small storage heater from 5 to 30 litres. Wall-mounted storage heaters from 50 to 120 litres. Small 5-litre storage heaters supply hot water for a single point-of-use e.g. the kitchen sink. For higher hot water demands, our SX wall-mounted storage heaters with 50, 80, 100 or 120 litres capacity provide an economical solution. 4 < Storage heater catalogue Storage heater catalogue > 5

4 Small storage heater 5 litres Small storage heater 10 litres Small storage water heater S 5 Small storage water heater S 10 The small storage heater S 5 provides up to 5 litres of hot water for one point-of-use (e.g. the kitchen sink) at the preselected temperature. To avoid exposing the unit to water line pressure, it requires a special open-outlet tap for vented hot water heaters. > Vented small 5-litre storage heaters for hot water supply at a single point-of-use > Temperature control approx. 35 C bis 85 C with available energy-saver range and optional temperature limitation at 38 C, 55 C or 65 C > Can only be used with a special open-outlet tap for vented hot water heaters With its 10-litre capacity, this storage heater also fulfils an increased hot water demand at a kitchen sink. Due to its long-lasting copper tank, it allows for vented as well as unvented installation in combination with a safety assembly. > Unvented small 10-litre storage heater for hot water supply at one or two points-of-use > Corrosion-proof and therefore maintenance-free internal copper tank with high-quality heat insulation > Temperature control approx. 5 C to 80 C > For vented installation (with open-outlet tap) and unvented installation (with safety assembly) > Safety temperature limiter as dry-run protection Energy efficiency class A S 5-O (oversink model) S 5-U (undersink model) Part number: Content [litres]: 5 Type: vented Water connections (thread connections): G ½" G ⅜" Temperature range [ C]: approx approx. mixed water amount 40 C at 65 C 1) [litres]: 9.1 Nominal power rating (kw): 2.0 Voltage [V]: Nominal current [A]: 9 Heating time t = 55 K 2) [min]: 10 Standby power consumption at 65 C [kwh / 24h]: Internal tank: plastic Function indicator: Temperature limit adjustable to [ C]: 38 / 55 / 65 Protection class: IP 24 Dimensions (height width depth) [cm]: Power cable: approx. weight filled with water [kg]: 8.5 1) At an inlet temperature of 12 C 2) Temperature increase e.g. from 10 C to 65 C with plug Energy efficiency class A S 10-O (oversink model) S 10-U (undersink model) Part number: Content [litres]: 10 Type; maximum operating pressure [MPa (bar)]: unvented 1) ; 0.8 (8) Water connections (thread connections): G ½" G ⅜" Temperature range [ C]: 5 C ( ) / 30 C 35 C (ECO) / 55 C / 80 C (MAX) approx. mixed water amount 40 C 2) [litres]: 20 Nominal power rating (kw): 2.2 Voltage [V]: Nominal current [A]: 10 Heating time t = 55 K 3) [min]: 17 Standby power consumption at 65 C [kwh / 24h]: Internal tank: copper Function indicator: Protection class: IP 24 Dimensions (height width depth) [cm]: Power cable: with plug approx. weight filled with water [kg]: ) This storage heater can also be operated as an open-outlet system. 2) With an inlet temperature of 15 C and a content temperature of 65 C 3) Temperature increase e.g. from 15 C to 70 C 6 < Storage heater catalogue Storage heater catalogue > 7

5 Small storage heater 15 litres Wall-mounted storage heaters 30 litres Small storage water heater S 15 Hot water storage heater S 30 With its 15-litre capacity, this storage heater also fulfils large hot water demand at a kitchen sink. Due to its long-lasting copper tank, it allows for vented as well as unvented installation in combination with a safety assembly. > Unvented small 15-litre storage heater for hot water supply at one or two points-of-use > Corrosion-proof and therefore maintenance-free internal copper tank with high-quality heat insulation > Temperature control approx. 5 C to 80 C > For vented installation (with open-outlet tap) and unvented installation (with safety assembly) The 30-litre wall-mounted storage heater S 30 fulfils the medium hot water demand. The high-quality hard foam insulation helps to minimise its energy use. > Unvented wall-mounted storage heater with 30-litres capacity for the hot water supply at one or more points-of-use > Internal tank with special enamel coating > Can be used in vented or unvented installations > Continuous temperature adjustment up to approx. 75 C > Corrosion protection due to special enamel coating and magnesium protection anode Energy efficiency class B S 15-O (oversink model) Part number: Content [litres]: 15 Type; maximum operating pressure [MPa (bar)]: unvented 1) ; 0.8 (8) Water connections (thread connections): G ½" G ⅜" Temperature range [ C]: 5 C ( ) / 30 C 35 C (ECO) / 55 C / 80 C (MAX) approx. mixed water amount 40 C 2) [litres]: 30 Nominal power rating (kw): 2.2 Nominal current [A]: 10 Voltage [V]: Heating time t = 55 K 3) [min]: 26 Standby power consumption at 65 C [kwh / 24h]: Internal tank: copper Function indicator: Protection class: IP 24 Dimensions (height width depth) [cm]: Power cable: with plug approx. weight filled with water [kg]: 22.5 A S 15-U (undersink model) 1) This storage heater can also be operated as an open-outlet system. 2) With an inlet temperature of 15 C and a content temperature of 65 C 3) Temperature increase e.g. from 15 C to 70 C Energy efficiency class C S 30 Part number: Content [litres]: 30 Type; maximum operating pressure [MPa (bar)]: unvented 1) ; 0.6 (6) Water connections (thread connections): G ½" Temperature range [ C]: 75 approx. mixed water amount 40 C 2) [litres]: 48 Nominal power rating (kw): 2.0 Voltage [V]: Nominal current [A]: 9 Heating time t = 45 K 3) [min]: 50 Standby power consumption at 65 C [kwh / 24h]: 0.85 Internal tank: specially enamelled steel Function indicator: Single-circuit operation: Protection class: IP 25 Dimensions (height width depth) [cm]: Power cable: with plug approx. weight filled with water [kg]: 44 1) This storage heater can also be operated as an open-outlet system. 2) With an inlet temperature of 15 C and a content temperature of 65 C 3) Temperature increase e.g. from 15 C to 60 C 8 < Storage heater catalogue Storage heater catalogue > 9

6 Wall-mounted storage heaters 50 to 100 litres Wall-mounted storage heaters 50 to 120 litres Hot water storage heater S 50, 80, 100 Hot water storage heater SX 50, 80, 100, 0, 120 Whenever larger water amounts are required, these wall-mounted storage heaters provide the necessary capacities. The special enamel coating and a magnesium anode provide corrosion protection for the internal tank. > Unvented wall-mounted storage heater with 50, 80 or 100 litres capacity > Continuous temperature adjustment up to approx. 70 C with temperature display > Can be used in vented or unvented installations > Corrosion protection due to special enamel coating and magnesium protection anode The storage capacity of these storage heaters ranges from 50 to 120 litres and provides large mixed water amounts for increased hot water demands. Electronic controls and a dual-circuit system ensure economical operation, since the stored water can be heated using the cost-efficient night energy rate. > Wall-mounted storage water heater with 50, 80 or 120 litre capacity > Push-button control panel with hot water capacity indicator, quick-heat button and consumption display > Internal steel tank with high-grade protective titanium enamel coating and universal connector for singlecircuit or economical dual-circuit operation > Can be heated at the cost- effective night energy rate > High-quality stainless steel heating elements with inspection flange and drain nozzle Energy efficiency class D S 50 S 80 S 100 Part number: Content [litres]: Type; maximum operating pressure [MPa (bar)]: unvented 1) ; 0.6 (6) Water connections (thread connections): G ½" Temperature range [ C]: 70 approx. mixed water amount 40 C [litres]: Nominal power rating (kw): 2.0 Voltage [V]: Nominal current [A]: 9 Heating time t = 45 K 3) [min]: Standby power consumption at 65 C [kwh / 24h]: Internal tank: specially enamelled steel Hot water capacity indicator / function indicator: / Protection class: IP 25 Dimensions (height width depth) [cm]: Power cable: with plug approx. weight filled with water [kg]: ) This storage heater can also be operated as an open-outlet system. 2) With an inlet temperature of 15 C and a content temperature of 65 C 3) Temperature increase e.g. from 15 C to 60 C Energy efficiency class C SX 50 SX 80 SX 100 SX 120 Part number: Content [litres]: Type; maximum operating pressure [MPa (bar)]: unvented; 0.6 (6) Water connections (thread connections): G ½" Temperature range [ C]: 40 / 60 / 85 approx. mixed water amount 40 C at 65 C [litres]: Nominal power rating (kw): 0.75 / / / / 6.0 Voltage [V]:, 2~ / N / PE 400 V AC, 3~ / N / PE 400 V AC 3) Nominal current [A]: Heating time t = 45 K 1) [min]: 37 / 220 2) 44 / 264 2) 55 / 330 2) 66 / 198 2) Standby power consumption at 65 C [kwh / 24h]: Internal tank: steel with protective titanium enamel coating Function indicator / hot water capacity indicator: / Push-button control panel / quick-heat button: / Protection class: IP 24 Dimensions (height width depth) [cm]: Power cable: permanent connection approx. weight filled with water [kg]: ) Temperature increase e.g. from 15 C to 60 C 2) Heating time at Max. or Min. setting 3) Follow the regulations of your local energy provider 10 < Storage heater catalogue Storage heater catalogue > 11

7 Accessories: Open-outlet taps Accessories: Safety assemblies SNT Two-handle temperature control mixer tap with swivel spout 15 cm SNT: Part no SGU Undersink safety assembly with non-return valve, pressure reducer and flexible connecting hoses SGU: Part no SEO Single-lever oversink mixer tap with swivel spout 20 cm SEO: Part no SGUT T-piece kit for installation of an additional tap SGUT: Part no SNO Two-handle wall-mounted mixer tap with isolating valve, swivel spout 16 cm and flow control SNO: Part no SG Oversink safety assembly (6 bar) SG: Part no Aerators for tap adapters, female and male threads (for small storage water heaters S 5, S 10 and S 15) Aerator insert for tap adapter M 22/24 at the tap CSS: Part no SGM Oversink safety assembly (6 bar), with pressure-reducing valve up to 10 bar SGM: Part no Aerator with chrome tap adapter M 22i (suitable for taps with male threads at the outlet) CSSi: Part no < Storage heater catalogue Storage heater catalogue > 13

8 The intelligent instant boiling water heaters put an end to waiting for boiling water. They provide boiling water for tea, coffee or other hot beverages by simply pushing a button. They can be even more efficient than conventional tea kettles or electric kettle, which often heat more water than is actually needed. This makes the units indispensable for beverage preparation in cafeterias, restaurants, hotels or hospitals. Boiling water heaters Now it s getting hot. Weekly energy demand (comparison): 100% 9 % 20 % 28 % Electric kettle Zip Hydroboil HBE 6 Zip Hydroboil HBE 6 Zip Hydroboil HBE 6 Continuous operation Energy-saving mode with on/off periods Researchers at Aston University in Birmingham have shown that the weekly energy demand for typical uses (e. g. tea and coffee preparation) with instant boiling water heaters can be up to 28 % lower than a conventional electric kettle. This was based on ten hours of daily operation from Monday to Friday, and during the rest of the time the Zip Hydro boil automatically switches to energy-saving mode or turns off completely. 14 < Storage heater catalogue Storage heater catalogue > 15

9 Instant boiling water heaters from 3 to 40 litres. Boiling water heater 5 litres. Instant boiling water heater Zip Hydroboil HBE 6 For smaller demands: Boiling water heater K 5 16 < Storage heater catalogue Storage heater catalogue > 17

10 Wall-mounted instant boiling water Instant boiling water heater Zip Hydroboil HBE Installation Never wait for hot water again! One push of a button and you ll have a pot of steaming hot tea or coffee. A real time saver for the work place! > Instant boiling water heater for continuous supply of boiling water Boiling water at the touch of a button Hanging cupboard 150 > Premium insulation and cool touch two way tap with safety lock 20 Case: white finish > The push-lever valve allows for easy dispensing of hot water for a single cup, lifting the lever will conveniently fill a whole pot, with safety lock > LCD display for operation and function indicators > Optional energy saver setting (automatic temperature drop to 65 C after longer periods of inactivity, via light sensor or 24 / 7 timer) Button valve with safety lock Power cable with plug 230 V AC 50 Hz 65 Case: stainless steel All measurements in mm boiling > HBE HBE HBE Part number [case: white finish]: Part number [case: stainless steel]: Water connection (thread connection): G ½" Water set temperature [ C]: Boiling water content [litres / cups 1) ]: 3 / 18 5 / / 45 Boiling water capacity [litres / cups 1) / h]: Recovery time [cups 1) / min]: Heating time for complete fill-up 2) [min]: Standby power consumption [kwh / 24h]: 1.1 3) 1.2 3) 1.3 3) Nominal power rating at voltage [kw]: Voltage: Protection class: IP 20 Dimensions (height width depth) [cm]: Power cable: with plug approx. weight filled with water [kg]: ) Standard cup with 167 ml 2) At 10 C inlet temperature 3) Can be reduced by up to 29 % when activating the energy saving mode Convenient filling of tea or coffee pots with raised lever Installation options: optional CLARIS ULTRA filter Drain bowl Drain 1. Concealed installation with visible drain bowl 2. Exposed installation with pipe section 18 < Storage heater catalogue Storage heater catalogue > 19

11 Wall-mounted instant boiling water Instant boiling water heater Zip Hydroboil KA Installation drawing The large instant boiling water heaters allow for effective operation and quickly prepared hot beverages, even in large quantities. This heater significantly increases productivity in restaurants, hospitals and staff cafeterias. > Instant boiling water heater for continuous supply of boiling water in large quantities Convenient filling of tea or coffee pots with lowered lever > Thermostatically controlled, twin-chamber technology with stainless steel boiling tank prevents the mixing of cold and hot water > Premium insulation and cool touch two way tap with safety lock > Dispensing tap for convenient filling of tea or coffee pots or single cups > No escaping steam the steam is used internally to heat the incoming water > For hot beverage preparation in offices, cafeterias, restaurants, hotel, hospitals, catering services etc. 120 Concealed installation boiling > KA 15 KA 25 KA 40 Part number [case: white finish]: Water connection (thread connection): G ½" Boiling water set temperature [ C]: Boiling water content [litres / cups 1) ]: 15 / / / 240 Boiling water capacity [cups 1) / h]: Recovery time [cups 1) / min]: Heating time for complete fill-up 2) [min]: Standby power consumption [kwh / 24h]: Nominal power rating at voltage [kw]: Voltage: Function indicator: Protection class: IP 20 Dimensions (height width depth) [cm]: Power cable: permanent connection approx. weight filled with water [kg]: ) Standard cup with 167 ml 2) at 10 C inlet temperature All measurements in mm 200 unter Putz Exposed installation auf Putz 20 < Storage heater catalogue Storage heater catalogue > 21

12 Boiling water for smaller demand. Electric wall kettle K5 The electric wall kettle is mounted above the sink. It is used for demand-based hot water preparation at home or a work place. The user fill the unit with up to 5 litres of water and it is heated to the desired temperature between approx. 37 C and the boiling point (99 C). > Boiling water heater for hot water preparation from one cup up to 5 litres > Temperature range from approx. 37 C to the boiling point (99 C) > Integrated tap > Overflow drain integrated in the swivel spout > Boiling point control > Secure wall-mounted installation These filters are ion exchangers that combine water softening and water filtration as well as ph adjustment. These water heaters provide a cost-effective, compact and reliable method to reduce water hardness. The filters also improve the taste of the water, since chlorine, odours and flavours are reduced. The special filters are installed in the water inlet line before the boiling water heater system*. > Uses ion exchanger resins with ph value, the ph value stabilisation prevents excessive acid content > Stabilisation and active carbon from coconut shells with especially high capacity > In order to reach the appropriate water hardness, a small amount of the active carbon-filtered water bypasses the water softening stage Accessories for Zip Hydroboil : CLARIS ULTRA filter systems for water softening > Reduces water hardness, which can lead to mineral deposits in boiling water heater systems > Hygienic and simple exchange of filter cartridges. Internal filter components are free from user contact or contamination boiling > K 5 Part number: Water connections (thread connections): G ½" Temperature range [ C]: Contents [litres / cups 1) ]: 5 / 30 Heating time for complete fill-up 2) [min]: 14.5 Nominal power rating (kw): 2.0 Voltage: Protection class: IP 44 Function indicator: Case: plastic / white Internal tank: plastic Boiling point control: Length of swivel spout [cm]: 20 Dimensions (height width depth) [cm]: Power cable: with plug approx. weight filled with water [kg]: 7.5 1) Standard cup with 167 ml 2) At 10 C inlet temperature > For the Hydroboil series (HBE and KA ), we recommend the CLARIS consumption meter (Part no ) with ⅜ inch thread as an optional accessory. Filter> ULTRA 500 ULTRA 1000 ULTRA 2000 Filter head universal [part no.]: Filter cartridge [part no.]: Capacity at 10 KH [litres]: Required pressure [bar]: 2 8 / at stable pressure Flow rate [L/min]: max. 1.9 Inlet temperature [ C]: 4 30 Dimensions height [cm]: Dimensions diameter [cm]: *) For hot beverage, coffee specialty drink and tea preparation units 22 < Storage heater catalogue Storage heater catalogue > 23

13 Accessories: Zip Hydroboil Accessories: Zip Hydroboil KAT 1 Stainless steel drip tray, cm KAT 1: Part no KA AZ Connection kit for 1 or 2 additional side taps for KA 15 / KA 25 KA AZ: Part no KAT 2 Stainless steel drip tray with drainage connection, cm KAT 2: Part no KA A KAS 1 Sink mounted chromed tundish Connection kit for 1 or 2 additional side taps for KA 40 KA A: Part no KAS 1: Part no KAS 2 Wall mounted chromed tundish KAS 2: Part no KAW Angled connector for flush mounting KAW: Part no KA Z Addition tap for KA 15 to 40 KA Z: Part no < Storage heater catalogue Storage heater catalogue > 25

14 1 < Catalogue Learn, experience and inform. > Learn and experience via ios apps CLAGE Smart Experience free Discover the Smart Control app and learn about the advantages of decentralised hot water supply. CLAGE Smart Control Our ipad app for use with a Smart Control system. For details see our catalogue Energy-efficient e-instant water heaters. CLAGE Hot Water free This smartphone app provides extensive product consultation, information, explanation of technical terms, photos and contact data. Electronically controlled instantaneous water heaters Drinking water systems Zip HydroTap > Inform Catalogue Energy-efficient E-instant water heaters This catalogue provides extensive information about our energy-efficient and convenient E-instant water heaters for use at washbasins, in the kitchen, shower or bathroom. Catalogue Zip HydroTap drinking water systems Simply efficient. Whether boiling, chilled or sparkling: With Zip, we always have the correct drinking water system for you. > Follow us! Follow us! Here you ll find online product consultation, product information an additional material for download, videos, references and of course everything about our products and our company. 26 < Storage heater catalogue

15 CLAGE GmbH Pirolweg Lüneburg Germany Phone: Fax: info@clage.de Dealer imprint Subject to technical changes, design changes and errors. All trademarks and brand names are the property of their respective owners. Copyright notice: fotolia.com / h368k742 (S. 5) All other photos and illustrations: CLAGE Reprints, including excerpts, forbidden without the prior written permission of the publisher