Ball Valve Features and Benefi ts B2...VS/VSS, B3...L, B6...VS

Transcription

1 all Valve Features and enefi ts 2...VS/VSS, 3...L, 6...VS P /13 - Subject to change. elimo ircontrols (US), Inc. 2-way and 3-way confi guration ronze with stainless steel trim (2-way) Nickel plated brass body (3-way) educed and full port capacities Two piece construction Electronic actuation NPT and fl anged connections ide C v range ir gap for use with hot water and steam systems Live load low maintenance stem packing 2 year warranty US CND LTIN MEIC / CIEN 1

2 Flow Pattern, Operation and Installation all Valves FLO PTTEN Open CC Flow Direction Closed C to Open C to Open CC NOTE: 3 L are piped differently than 3 CCV Valves. VS SEIES LL VLVE PIPING DIGMS 2-way Valve Piping Diagram 3-way Diverting Valve Piping Diagram NOTE: To avoid torque increase during off season shut down, or other periods of inactivity longer than 1 month - the valve should be exercised (actuator or manually driven full open-closed cycle) at least once per month. This is necessary to avoid any application problems after an off season shut down. PIPING/MOUNTING OIENTTION ssembly can be mounted horizontally or vertically for water applications. For steam applications the valve can be mounted vertically but if mounted horizontally the valve must be 90 off center of the pipe. Do not install with actuator below pipe. (ater application only) (Steam or water application) P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

3 Piping Sizing Geometry all Valves VLVE SIZE C v TYPE MODEL # ¾ Fp Cv 1 Fp Cv 1¼ Fp Cv 1½ Fp Cv LINE SIZE ½ 1 2 NPT 2050VS ½ 2 2 NPT 2050VS ½ 4 2 NPT 2050VS ½ 15 2 NPT 2050VS ¾ 30 2 NPT 9VS/VSS ¾ 51 2 NPT 0VS NPT 4VS/VSS NPT 5VS ¼ 48 2 NPT 2VS/VSS ½ 84 2 NPT 9VS/VSS ½ NPT 240VS NPT 249VS/VSS NPT 250VS ½ NPT 265VS/VSS NPT 280VS/VSS ½ NPT 315L ¾ NPT 320L NPT 325L ¼ 34 3 NPT 332L ½ 57 3 NPT 340L NPT 350L FLG 650VS ½ FLG 665VS FLG 680VS FLG 6100VS FLG 6150VS FLG 6200VS FLG 6250VS Fp Cv 2½ Fp Cv 3 Fp Cv 4 Fp Cv 5 Fp Cv 6 Fp Cv 8 Fp Cv 10 Fp Cv P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN 3

4 iring Instructions all Valves GENEL IING INSTUCTIONS NING The wiring technician must be trained and experienced with electronic circuits. Disconnect power supply before attempting any wiring connections or changes. Make all connections in accordance with wiring diagrams and follow all applicable local and national codes. Provide disconnect and overload protection as required. Use copper, twisted pair, conductors only. If using electrical conduit, the attachment to the actuator must be made with fl exible conduit. lways read the controller manufacturer s installation literature carefully before making any connections. Follow all instructions in this literature. If you have any questions, contact the controller manufacturer and/or elimo. Transformer(s) Typically actuators require a 24 VC class 2 transformer and draw a maximum of 10 V per actuator. The actuator enclosure cannot be opened in the fi eld, there are no parts or components to be replaced or repaired. EMC directive: 89/336/EEC Software class : Mode of operation type 1 Low voltage directive: 73//EEC Typical transformer sizing ctuator Series Voltage Max. V Per ctuator F LF N 24 4 L 24 3 CUTION It is good practice to power electronic or digital controllers from a separate power transformer than that used for actuators or other end devices. The power supply design in our actuators and other end devices use half wave rectifi cation. Some controllers use full wave rectifi cation. hen these two different types of power supplies are connected to the same power transformer and the DC commons are connected together, a short circuit is created across one of the diodes in the full wave power supply, damaging the controller. Only use a single power transformer to power the controller and actuator if you know the controller power supply uses half wave rectifi cation. Multiple actuators, one transformer Multiple actuators may be powered from one transformer provided the following rules are followed: 1. The TOTL current draw of the actuators (V rating) is less than or equal to the rating of the transformer. 2. Polarity on the secondary of the transformer is strictly followed. This means that all No. 1 wires from all actuators are connected to the common leg on the transformer and all No. 2 wires from all actuators are connected to the hotleg. Mixing wire No. 1 & 2 on one leg of the transformer will result in erratic operation or failure of the actuator and/or controls. Multiple actuators, multiple transformers Multiple actuators positioned by the same control signal may be powered from multiple transformers provided the following rules are followed: 1. The transformers are properly sized. 2. ll No. 1 wires from all actuators are tied together and tied to the negative leg of the control signal. See wiring diagram. ire type and wire installation tips For most installations, 18 or 16 Ga. cable works well with elimo actuators. Use code-approved wire nuts, terminal strips or solderless connectors where wires are joined. It is good practice to run control wires unspliced from the actuator to the controller. If splices are unavoidable, make sure the splice can be reached for possible maintenance. Tape and/or wire-tie the splice to reduce the possibility of the splice being inadvertently pulled apart. ire length for actuator installation Keep power wire runs below the lengths listed in the following tables. If more than one actuator is powered from the same wire run, divide the allowable wire length by the number of actuators to determine the maximum run to any single actuator. See section 1 for specifi c transformer sizing information for the actuator selected. Example: 3 actuators, 16 Ga wire 350 Ft 3 ctuators = 117 Ft. Maximum wire run P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

5 Nomenclature all Valves 2 24 VS MX 24 -MFT-X1 Valve 2 = 2-way 3 = 3-way 6 = 2-way Flanged Valve Size = ½ to = 2 to 10 (Flanged) Industrial Cv Construction/ Material VS = ronze ody, Stainless Steel all and Stem VSS = Stainless Steel ody, all and Stem L = Nickel Plated rass ody, Chrome Plated rass all and Stem ctuator Type Non-Spring eturn LM NM M GM SY SY P Spring eturn LF NF F Electronic Fail-Safe GK... Power Supply 24 = 24 VC/DC 120 = 120 VC 0 = 0 VC Control -3-X1 = On/Off, Floating Point -MFT-X1 = Multi-Function Technology = Ω -S = uilt-in uxiliary Switch Ordering Example P /13 - Subject to change. elimo ircontrols (US), Inc. 1 Choose the valve actuator combination. 4VS+MX24-MFT-X1 2 Specify preference or confi guration. Non-Spring Models NO = Normally Open NC = Normally Closed Spring eturn Models NO/FO = Normally Open/Fail Open NO/FC = Normally Open/Fail Closed NC/FO = Normally Closed/Fail Open NC/FC = Normally Closed/Fail Closed efers to valve ports to. 3 Set-Up +NO For MFT orders only - select programming code +Tagging (if needed) P (01) P-100xx (xx) P-200xx (xx) P-300xx (Fxx) P-400xx (Jxx) X-XXXXX X-XXXXX Control voltage applications Pulse width modulation applications Floating point applications On/off applications Create custom MFT confi guration code Create custom MFT confi guration in the fi eld with MFT actuator PC software 4 Does order require tagging? Tagging: Valves may be tagged per customer specifi cation. ($10.00 per tag) Example: HU-1 FCU-2 Part number for tagging: Complete Ordering Example: 4VS+MX24-MFT-X1+NO US CND LTIN MEIC / CIEN 5

6 2...VS Series, 2-way, all Valve ronze ody, Stainless Steel all and Stem Live-load packing set Stainless steel ball & stem low-out proof stem design Technical Data Media chilled or hot water, glycol, 35# steam Flow characteristic modifi ed equal percentage ction 90 rotation valve open C, valve closed CC Sizes ½, ¾, 1, 1¼, 1½, 2, 2½, 3 Type of end fi tting SE NPT (female connections) Materials: 1 Stem packing reinforced PTFE 2 Stem bearing reinforced PTFE 3 all 316 stainless steel 4 Seat (x2) reinforced PTFE w/ Durafi ll 5 etainer 16 (¾ - 1 ) stainless steel 584 (1¼ - 3 ) stainless steel 6 Gland 16 brass 7 Stem 316 stainless steel 8 Jam nut stainless steel 9 ody seal PTFE (1-1/4 to 3 ) 10 ody 584-C84400 bronze pplication This valve is typically used in air handling units on heating or cooling coils, and fan coil unit heating or cooling coils. Some other common applications include Unit Ventilators, VV ox re-heat coils and bypass loops. This valve is suitable for use in a hydronic system with variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Up to 35 psi steam ½ PSIG OG, Cold Non-Shock. Federal Specification: -V-35C,Type II Composition: Z Style: 3 Valve Nominal Size Type Suitable ctuators C v Inches DN [mm] 2-way NPT Spring Non-Spring eturn eturn 1 ½ VS-01 2 ½ VS-02 4 ½ VS ½ VS ¾ 20 9VS 51 ¾ 20 0VS VS VS 48 1¼ 32 2VS 84 1½ 40 9VS 177 1½ VS VS VS 503 2½ VS VS LF Series NF F Series LM Series NM M Series GM Series SY Series Pressure rating 600 psig OG Media temp. range - F to +280 F (-30 C to +138 C) Close-off pressure F Maximum differential <600 psig pressure (ΔP) Flow Patterns 10 P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

7 2...VSS Series, 2-way, all Valve Stainless Steel ody, all and Stem Live-load packing set Stainless steel ball & stem low-out proof stem design pplication These threaded valves are designed to provide modulating or two position control of hot or chilled water and saturated steam systems under 50 psi. Typical applications include reheat coils, vav terminal control, unit ventilators, and air handlers, especially in areas which have minimum profile requirements. Up to 50 psi steam ½ PSIG OG, Cold Non-Shock. Federal Specification: -V-35C,Type II, Composition: SS Style: 3 Technical Data Media chilled or hot water, glycol, 50# steam Flow characteristic modifi ed equal percentage ction 90 rotation valve open C, valve closed CC Sizes ½, ¾, 1, 1¼, 1½, 2, 2½ Type of end fi tting SE NPT (female connections) Materials: 1 Stem packing reinforced PTFE 2 Stem bearing reinforced PTFE 3 all 316 stainless steel 4 Seat (x2) reinforced PTFE w/ Durafi ll 5 etainer 16 (¾ - 1 ) stainless steel 584 (1¼ - 3 ) stainless steel 6 Gland Stem 316 stainless steel 8 Jam nut stainless steel 9 ody seal PTFE (1¼ to 3 ) 10 ody 351-CF8M 316 stainless steel Valve Nominal Size Type Suitable ctuators C v Inches DN Spring Non- Spring 2-way NPT [mm] eturn eturn 15 ½ VSS ¾ 20 9VSS VSS 48 1¼ 32 2VSS 84 1½ 40 9VSS VSS 503 2½ VSS LF Series F Series NM Series M Series GM Series SY Series P /13 - Subject to change. elimo ircontrols (US), Inc. Pressure rating 2000 psig OG (½ - 1 ) Media temp. range - F to +298 F (-30 C to +148 C) Close-off pressure F Maximum differential <600 psig pressure (ΔP) Flow Patterns US CND LTIN MEIC / CIEN 7

8 3...L Series, 3-way, all Valve Chrome Plated rass all and Nickel Plated Stem pplication This valve is typically used in air handling and fan coil units on heating or cooling coils, unit ventilators, VV box re-heat coils, and bypass loops. This valve is suitable for use as a diverting valve only. Technical Data Media Flow characteristic ction chilled or hot water, 60% glycol modifi ed linear 90 rotation to open C, to open CC Sizes ½, ¾, 1, 1¼, 1½, 2 Type of end fi tting NPT female ends Materials: ody nickel plated brass all chrome plated brass Stem nickel plated brass Stem seal o-ring EPDM Valve seat PTFE Leakage NSI VI Pressure rating 600 psig OG 600 psi DN (3...L) 400 psi DN (3...L) Media temp. range 0 F to 250 F [-18 C to +120 C] Close-off pressure 200 psi Maximum differential 50 psi pressure (ΔP) Valve Nominal Size Type Suitable ctuators C v Inches DN [mm] 3-way Spring Non-Spring Electronic NPT eturn eturn Fail-Safe 6.4 ½ L 12.8 ¾ L L 34 1¼ L 57 1½ L L LF Series F Series L Series N Series w Flow Patterns to Open C to Open CC P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

9 6...VS Series, 2-way, all Valve Cast Iron ody, Stainless Steel all and Stem Same end to end dimension as conventional flanged iron gate valve Fast quarter turn open or closed operation Stainless steel ball and stem Positive shut-off Two-piece body construction Technical Data Media chilled or hot water, glycol, 50# steam Flow characteristic modifi ed equal percentage ction 90% rotation valve open C, valve closed CC Sizes 2, 2½, 3, 4, 6, 8, 10 Type of end fi ttings fl anged 125# NSI bolt pattern Materials: 1 ody cast iron - STM 126 Class 2 End cap cast iron - STM 126 Class 3 all 304 stainless steel - STM Seats PTFE 5 Stem 304 stainless steel - ISI Packing PTFE 7 Gland cast iron - STM 126 Class 8 Gasket PTFE 9 Nut steel - STM 6 pplication Ideal for water service where a non-corrosive, clean cosmetic appearance is required. Optional FD approval, suitable for potable water and food contact. Sizes: 2-10 (50-250mm) 200 psi CP (cold water pressure) (non-shock) pproved valves shall comply with the merican Standard for face-to-face dimensions (NSI 16.10) for Class 125 cast iron flanged gate valves. The dimensions and drilling of end flanges conform to the merican cast iron flange standard, Class 125 (NSI 16.1). Valve Nominal Size Type Suitable ctuators C v Inches DN [mm] 2-way NPT Non-Spring eturn VS 420 2½ VS VS VS VS VS VS SY Series Pressure rating 200 psig OG Media temp. range - F to +298 F (-30 C to +148 C) Close-off pressure F Maximum differential <200 psi pressure (ΔP) US CND LTIN MEIC / CIEN 9

10 This Page Intentionally Left lank P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

11 all Valve Product ange Overview VS/VSS all Valve Product ange 2...VS/VSS, 3...L, 6...VS P /13 - Subject to change. elimo ircontrols (US), Inc. Valve Nominal Size Type Suitable ctuators C v Inches DN [mm] 2-way NPT 1 ½ VS-01 2 ½ VS-02 4 ½ VS ½ VS ¾ 20 9VS 51 ¾ 20 0VS VS VS 48 1¼ 32 2VS 84 1½ 40 9VS 177 1½ VS VS VS 190 2½ VS VS 15 ½ VSS ¾ 20 9VSS VSS 48 1¼ 32 2VSS 84 1½ 40 9VSS VSS 190 2½ VSS VSS 3-way NPT 6.4 ½ L 12.8 ¾ L L 34 1¼ L 57 1½ L L 2-ay Flanged VS 420 2½ VS VS VS VS VS VS Non-Spring eturn LM Series NM Series M Series GM Series NM Series M Series GM Series L Series N Series SY Series SY Series Spring eturn LF Series NF Series F Series LF NF F Series LF Series F Series Electronic Fail-Safe GK GK GK Mode of Operation The control valve is operated by an electronic actuator that responds to a standard voltage for on/off control, by a proportional VDC/4 20 m, or 3-point control system. The actuator will then move the ball of the valve to the position dictated by the contol signal thus changing the flow. Product Features Modified equal percentage of flow for 2, 3 and 6. Modified linear flow for 3. ctuator Specifications Control type Manual override Electrical connection Valve Specifications Service Flow characteristic on/off, fl oating point, proportional, 2-10 VDC multi-function technology (MFT) LM, NM, GM, M, SY, F, NF, GK 3 ft [1m] cable with ½ conduit fi tting Sizes ½ to 10 chilled or hot water, (60% glycol), steam modified equal percentage (2-way), modifi ed linear (3-way) End fi tting NPT (2...VS & 3.. L) fl anged (6...VS) Materials ody all Stem Seats 2-way 3-way Packing 2-way NPT 2-way fl anged Media temp range 2..VS, 6..VS 2..VSS 3...L ody pressure rating 3-way Maximum inlet pressure Steam ater Leakage bronze (2..VS), stainless steel (2..VSS), nickel plated brass (3...L), cast iron (6..VS) stainless steel, bronze (½ ) chrome plated brass (3...L) stainless steel, bronze (½ ) nickel plated brass (3...L) MPTFE LPTFE PTFE PTFE - F to +280 F [-30 C to +138 C] - F to +298 F [-30 C to +148 C] 0 F to 250 F [-18 C to +120 C] up to 2000 psig OG 600 psi DN (3...L) 400 psi DN (3...L) 35 psi 2..VS 50 psi 2..VSS, 6..VS 50 psi 3...L NSI class VI US CND LTIN MEIC / CIEN 11

12 LF ctuators, On/Off Dimensions with 2-ay Valve Models LF24 US LF24-S US LF120 US LF120-S US w/built-in ux. Switch w/built-in ux. Switch Technical Data Control on/off, fl oating point Power supply LF24(-S) US 24 VC ± 20% 50/60 Hz 24 VDC ± 10% LF120(-S) US 120 VC ± 10% 50/60 Hz Power consumption LF24(-S) US running 5 holding 2.5 LF120(-S) US running 5.5 holding 3.5 Transformer sizing 7 V, class 2 power source Electrical connection (-S models have 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cable Electrical protection 120V actuators double insulated Overload protection electronic throughout rotation ngle of rotation 95 Spring return direction reversible with C/CC mounting Position indication visual indicator 0 to 90 unning time <40 to 75 sec. (on/off) spring <25 -4 F to +1 F [-20 C to +50 C] <60 - F [-30 C] mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 gency listings UL 873, CS C.2 No. 24 certifi ed, CE Quality standard ISO 9001 Noise level max. 62 d() LF...-S US uxiliary switch 1 x SPDT, VC, UL Listed, adjustable 0 to 95 (double insulated) ated impulse voltage 800V (4kV for 120V model), Control pollution degree 3, Type of action 1. (1.. for -S models) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 2050VS ½ VS ½ VS ½ VS ½ VSS ½ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 315L 50 ½ [67] 1.73 [44] 1.42 [36] 320L 50 ¾ [78] 1.81 [46] 1.63 [42] 325L [87] 1.81 [46] 1.77 [45] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

13 LF ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuator may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., LF24-S US and LF120-S US incorporates a built-in auxiliary switch: 1 x SPDT, VC, UL listed, adjustable 0 to Common 2 + Hot 3 LF24 US 2 On/Off wiring for 24 VC/DC LF-08 Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off wiring for 120 VC 048-UX uxiliary Switch P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN 13

14 LF24-MFT US ctuators, Multi-Function Technology Dimensions with 2-ay Valve Models LF24-MFT US LF24-MFT-S US w/built-in ux. Switch Technical Data Control MFT Control signal 2 to 10 VDC (4-20m with 500 Ω resistor) Power consumption running 2.5 holding 1 Transformer sizing 5 V (class 2 power source) Electrical connection (-S models have 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cable Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20m 750 Ω for PM 500 Ω for on/off and fl oating point Feedback 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of rotation spring reversible with C/CC mounting motor reversible with built-in Position indication visual indicator unning time <40 to 75 sec. (on/off) 150 sec. independent of load (proportional) spring <25 -4 F to +1 F [-20 C to +50 C] <60 F [-30 C] mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 gency listings UL 873, CS C.2 No. 24 certifi ed, CE Noise level max. 62 d() Quality standard ISO 9001 LF24-MFT-S US uxiliary switch 1 x SPDT, VC, UL Listed, adjustable 0 to 95 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 2050VS ½ VS ½ VS ½ VS ½ VSS ½ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 315L 50 ½ [67] 1.73 [44] 1.42 [36] 320L 50 ¾ [78] 1.81 [46] 1.63 [42] 325L [87] 1.81 [46] 1.77 [45] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

15 LF24-MFT US ctuators, Multi-Function Technology iring Diagrams 24 VC/DC Transformer CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Position ( ) Feedback VDC (+) a (1) Common (2) Hot (3) Y Input (5) U Output 3 ctuators may also be powered by 24 VDC. CC C MFT 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). 5 Triac and can also be contact closures. 6 7 Control signal may be pulsed from either the Hot (Source) or Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. The actuators internal common reference is not compatible. On/Off control (C only) 7 Position Feedback VDC ( ) (+) 6 (1) Common (2) + Hot (3) Y Input (5) U Output 041 The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. CC C MFT NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink MFT P /13 - Subject to change. elimo ircontrols (US), Inc. Floating Point control Propotional 2 to 10 or 4 to 20 m control signal US CND LTIN MEIC / CIEN 15

16 NF ctuators, On/Off Dimensions with 2-ay Valve C F D Models NF24-X1 NFUP-X1 NFUP-S-X1 Technical Data Control Power consumption NF24-X1 NFUP-X1 Transformer sizing w/built-in ux. Switch on/off running 6 holding 2.5 running 6 holding 2.5 NF24-X1 NFUP(-S)-X1 8.5 V (class 2 power source) 6 24 VC (class 2 powe source) VC VC Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cables Electrical protection 120V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator unning time control <75 seconds spring <20 seconds mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C.2 No. 24 certified, CE Noise level max. 45 d() NFUP-S-X1 uxiliary switch 2 x SPDT, 3 ( V Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 9VS 400 ¾ VS 200 ¾ VSS 1000 ¾ P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

17 NF ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., NF24-S US incorporates a built-in auxiliary switch: 1 x SPDT, VC, UL listed, adjustable 5 to 85. Meets culus or UL and CS requirements without the need of an electrical ground connection. 1 1 Common 2 + Hot 3 On/Off wiring for NF24-X1 NF24-X _NF(X) 066_NF(X)UP NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. NFUP-X1 NFUP-S-X1 On/Off wiring for NFUP-X1, NFUP-S-X1 ht lk 067_NF(X)UP-S P /13 - Subject to change. elimo ircontrols (US), Inc. uxiliary Switch NFUP-S-X US CND LTIN MEIC / CIEN 17

18 NF ctuators, Multi-Function Technology Dimensions with 2-ay Valve C F D Models NFX24-MFT-X1 NFX24-MFT-S-X1 Technical Data Control MFT Control signal 2 to 10 VDC, (4 to 20 m with 500 Ω resistor) Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 20% / -10% Power consumption running 6.5 holding 3 Transformer sizing 9 V, (class 2 power source) Electrical connection ½ conduit connector 3 ft. [1m], 18 G appliance cable Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 1500 Ω for on/off and fl oating point Feedback output 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of rotation spring reversible with C/CC mounting motor reversible with built-in Position indication visual indicator, 0 to 95 unning time motor 150 seconds (default), variable (40 to 0 seconds) spring <20 -4 F to +1 F [-20 C to +50 C]; <60 - F [-30 F] mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54, Enclosure Type 2 gency listings culus acc. to UL / -2-14, CN/ CS E :02, CE acc. to 2004/108/EC & 2006/95/EC Noise level <40 d() 150 seconds, run time dependent <62 d() spring return NFX24-MFT-S-X1 uxiliary switch 2 x SPDT, VC, UL pproved one set at +10, one adjustable 10 to 90 Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 9VS 400 ¾ VS 200 ¾ VSS 1000 ¾ P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

19 NF ctuators, Multi-Function Technology iring Diagrams 2 CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. ( ) Control Signal (+) 4 to 20 m or 2 to 10 VDC Ω Ω 1/4 watt lk (1) Common ht (3) Y 1 Input, 2 to 10V Pnk (4) Y 2 Input Grn (5) U Output, 2 to 10V ctuators may also be powered by 24 VDC. CC C 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). VDC/4-20 m 5 Triac and can also be contact closures. 6 7 Control signal may be pulsed from either the Hot (Source) or Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. The actuators internal common reference is not compatible. ( ) 2 to 10 VDC Feedback Signal (+) lk (1) Common ed (2) Hot + ht (3) Y1 Input Pnk (4) Y2 Input Org (5) U Output 2 to 10V The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point Direction of rotation switch CC CC C C 5 5 (C only) Position ( ) Feedback VDC (+) lk (1) Common ht (3) Y Input Pnk (4) Y 2 Input Org (5) U Output PM P /13 - Subject to change. elimo ircontrols (US), Inc. Two Position 24 VC/DC Transformer ( ) Position Feedback VDC (+) (C Only) ( ) Control Signal 2-10 VDC or 4 to 20 m (+) 7 Ω 500 Ω 1/4 watt Min* Mid* Max* Normal** C a Functions 0% 50% 100% Control mode acc. to Y lk (1) Common ed (2) Hot ht (3) Y Input Pnk (4) Y 2 Input Org (5) U Output 5 lk (1) Common ht (3) Y 1 Input, 2 to 10V Pnk (4) Y 2 Input Org (5) a b c * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. Override Control to Min, Mid, Max, Positions US CND LTIN MEIC / CIEN 19

20 NF ctuators, Multi-Function Technology Dimensions with 2-ay Valve C F D Models NFX24 Technical Data Control MFT Control signal Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 20% / -10% Power consumption running 6.5 holding 3 Transformer sizing 9 V (class 2 power source) Electrical connection ½ conduit connector 3 ft. [1m], 18 G appliance cable Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 1500 Ω for on/off and fl oating point Feedback output 2 to 10 VDC, 0.5 m max ngle of rotation 95 (adjustable with mechanical end stop, 35 to 95 ) Direction of rotation spring reversible with C/CC mounting motor reversible with built-in Position indication visual indicator, 0 to 95 unning time control 150 seconds (default), variable (40 to 0 seconds) spring <20 -4 F to +1 F [-20 C to +50 C]; <60 - F [-30 F] mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54, Enclosure Type 2 gency listings culus acc. to UL / -2-14, CN/ CS E :02, CE acc. to 2004/108/EC & 2006/95/EC Noise level <40 d() 150 seconds, run time dependent, <62 d() spring return Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 9VS 400 ¾ VS 200 ¾ VSS 1000 ¾ P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

21 NF ctuators, Multi-Function Technology P /13 - Subject to change. elimo ircontrols (US), Inc Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. Low Limit Control Series Ω Series 90 low limit control 135 Ω for 0 to 50% control 280 Ω for 0 to 100% control lk (1) Common ht (3) 24 ht (4) ht (5) lk (1) Common ht (3) 24 ht (4) ht (5) lk (1) Common ht (3) 24 ht (4) ht (5) High Limit Control Series 90 iring Multiple ctuators to a Series 90 lk (1) Common Series 90 high limit control Ω Shunting esistor 24 Series 90 No. of actuators esistance Ω Ω Ω Ω 6 28 Ω esistor Kit No. ZG-03 To other actuators lk (1) Common ht (3) 24 ht (4) ht (5) ht (3) 25 ht (4) ht (5) lk (1) Common ht (3) 25 ht (4) ht (5) iring Multiple ctuators to a Series 90 using a Minimum Position Potentiometer Series 90 Shunting esistor 24 H205 Changeover Occupied Contact To other actuators S963 Minimum Position Potentiometer lk (1) Common 25 ht (3) ht (4) ht (5) lk (1) Common ht (3) 25 ht (4) ht (5) Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 24 H205 Changeover Shunting esistor 973, 7100 No. of actuators esistance Ω Ω Ω esistor Kit No. ZG Shunting esistor Y 973, 7100 T775 Q209 Minimum Position Potentiometer To other actuators To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) Occupied Contact Honeywell T675 Morning armup lk (1) Common ht (3) 25 ht (4) ht (5) Used with the 973 and 7100 controllers Honeywell T675 Morning armup Honeywell Q209 Minimum Position Potentiometer lk (1) Common ht (3) 25 ht (4) ht (5) lk (1) Common 020 ht (3) 25 ht (4) ht (5) US CND LTIN MEIC / CIEN

22 F ctuators, On/Off Dimensions with 2-ay Valve C F D Models F24-X1 FUP-X1 FUP-S-X1 Technical Data Control Power consumption FUP-X1 FUP-S-X1 Transformer sizing w/built-in ux. Switches on/off running 5 holding 2.5 running 7 holding 3.5 F24-X1 FUP(-S)-X1 7.5 V (class 2 power source) 7 24 VC (class 2 power source) VC VC Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cables Electrical protection 120V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator Manual override hex crank unning time control 150 seconds independent of load spring <20 seconds mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C.2 No. 24 certifi ed, CE Noise level max. 45 d() FUP-S-X1 uxiliary switches * Dual Mounted ctuators 2 x SPDT, VC, UL listed, one switch is fi xed at +5, one is adjustable 25 to 85 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 4VS VS VS 200 1¼ *9VS 600 1½ *240VS 600 1½ *249VS VSS VSS ¼ *9VSS ½ *249VSS Dimensions with 3-ay Valve 4.04 [102.7] 3.93 [99.9] Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 332L 50 1¼ [105] 2.00 [51] 2.19 [56] 340L 50 1½ [1] 2.44 [62] 2.61 [67] 350L [142] 2.67 [68] 3.11 [79] 9.77 [248.2] 2.50 [63.5] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

23 F ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., F24-S US incorporates two built-in auxiliary switches: 2 x SPDT, VC, UL listed, one switch is fi xed at +5, one is adjustable 25 to 85. p j y 1 Common 2 + Hot 3 F24-X1 2 On/Off iring for F24-X1 194_F24-X1 003_F24-X1 Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off iring for FUP-X1, FUP-S-X1 FUP-X1 FUP-S-X1 195_FUP-S-X1 uxiliary Switches FUP-S-X1 P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

24 F ctuators, Multi-Function Technology Dimensions with 2-ay Valve C F D Models FX24-MFT-X1 FX24-MFT-S-X1 FX24 w/built-in ux. Switches Technical Data Control MFT Control signal 2 to 10 VDC, (4 to 20 m with 500 Ω resistor) Ω (MFT95) Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 7.5 holding 3 Transformer sizing 10 V (class 2 power source) Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft. [1m], 18 G appliance cable Overload protection electronic throughout rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback output 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of rotation spring reversible with C/CC mounting motor reversible with built-in Position indication visual indicator Manual override hex crank unning time control 150 seconds independent of load spring <20 seconds mbient temperature - F to +1 F [-30 C to +50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C.2 No. 24 certifi ed, CE Noise level max. 45 d() FX24-MFT-S-X1 uxiliary switches * Dual Mounted ctuators 2 x SPDT, VC, UL listed, one switch is fi xed at +5, one is adjustable 25 to 85 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 4VS VS VS 200 1¼ *9VS 400 1½ *240VS 50 1½ *249VS VSS VSS ¼ *2VSS ¼ *9VSS ½ *249VSS Dimensions with 3-ay Valve 4.04 [102.7] 3.93 [99.9] Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 332L 50 1¼ [105] 2.00 [51] 2.19 [56] 340L 50 1½ [1] 2.44 [62] 2.61 [67] 350L [142] 2.67 [68] 3.11 [79] 9.77 [248.2] 2.50 [63.5] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

25 F ctuators, Multi-Function Technology iring Diagrams 24 VC/DC Transformer CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Position ( ) Feedback VDC (+) a (1) Common (2) Hot (3) Y Input (5) U Output 3 ctuators may also be powered by 24 VDC. 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). On/Off control CC C MFT 5 Triac and can also be contact closures. 6 7 Control signal may be pulsed from either the Hot (Source) or Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. The actuators internal common reference is not compatible. (C only) 7 Position Feedback VDC ( ) (+) 6 (1) Common (2) + Hot (3) Y Input (5) U Output 041 The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink CC C MFT 302_FX24-MFT...MFT P /13 - Subject to change. elimo ircontrols (US), Inc. Floating Point control Propotional 2 to 10 or 4 to 20 m control signal uxiliary Switches FX24-MFT-S-X US CND LTIN MEIC / CIEN 25

26 F ctuators, Multi-Function Technology Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. Low Limit Control Series Ω Series 90 low limit control 135 Ω for 0 to 50% control 280 Ω for 0 to 100% control lk (1) Common ht (3) 24 ht (4) ht (5) lk (1) Common ht (3) 24 ht (4) ht (5) lk (1) Common ht (3) 24 ht (4) ht (5) High Limit Control Series 90 iring Multiple ctuators to a Series 90 lk (1) Common Series 90 high limit control Ω Shunting esistor 24 Series 90 No. of actuators esistance Ω Ω Ω Ω 6 28 Ω esistor Kit No. ZG-03 To other actuators lk (1) Common ht (3) 24 ht (4) ht (5) ht (3) 25 ht (4) ht (5) lk (1) Common ht (3) 25 ht (4) ht (5) iring Multiple ctuators to a Series 90 using a Minimum Position Potentiometer Series 90 Shunting esistor 24 H205 Changeover Occupied Contact To other actuators S963 Minimum Position Potentiometer lk (1) Common 25 ht (3) ht (4) ht (5) lk (1) Common ht (3) 25 ht (4) ht (5) Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers 24 H205 Changeover Shunting esistor 973, 7100 No. of actuators esistance Ω Ω Ω esistor Kit No. ZG Shunting esistor Y 973, 7100 T775 Q209 Minimum Position Potentiometer To other actuators To other actuators lk (1) Common ht (3) 25 ht (4) ht (5) Occupied Contact Honeywell T675 Morning armup lk (1) Common ht (3) 25 ht (4) ht (5) Used with the 973 and 7100 controllers Honeywell T675 Morning armup Honeywell Q209 Minimum Position Potentiometer lk (1) Common ht (3) 25 ht (4) ht (5) lk (1) Common 020 ht (3) 25 ht (4) ht (5) P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

27 LM()X24-3-X1, LX24-3 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F P /13 - Subject to change. elimo ircontrols (US), Inc. Models LM24-3-X1 LMX24-3-X1 LX24-3 Technical Data Control Power supply Power consumption Transformer sizing Electrical connection LM24-3-X1 on/off, fl oating point 24 VC ± 20% 50/60 Hz 24 VDC ± 10% running 1.5 holding V (class 2 power source) ½ conduit connector 3 ft., 18 G plenum rated cables Overload protection electronic throughout 0 to 95 rotation Input impedance 600 Ω ngle of rotation 95 Torque 45 in-lbs [5 Nm] Direction of rotation reversible with Position indication reflective visual indicator (snap-on) Manual override external push button unning time 95 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS C.2 No. 24 certifi ed, CE acc. to 73//EEC Noise level <35 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F H1 H2 2050VS ½ VS ½ VS ½ VS ½ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 315L 50 ½ [67] 1.73 [44] 1.42 [36] 320L 50 ¾ [78] 1.81 [46] 1.63 [42] 325L [87] 1.81 [46] 1.77 [45] US CND LTIN MEIC / CIEN 27

28 LM()X24-3-X1, LX24-3 ctuators, On/Off, Floating Point iring Diagrams Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off control Floating Point or On/Off control Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow suffi cient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse fl ow direction. P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN

29 LMX24-MFT-X1, LX24-MFT ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F P /13 - Subject to change. elimo ircontrols (US), Inc. Models LMX24-MFT-X1 LX24-MFT Technical Data Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption 2 Transformer sizing 3.5 V (class 2 power source) Electrical connection 3 ft. [1m], 10 ft. [3m], 16 ft. [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input impedance 100k Ω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for on/off and fl oating point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation 95 Torque 45 in-lbs [5 Nm] Direction of rotation reversible with Position indication reflective visual indicator (snap-on) Manual override external push button unning time 150 seconds (default) variable (35 to 150 seconds) Humidity 5 to 95% H non-condensing (EN ) mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS E , CS C.2 No , CE acc. to 89/336/EEC Noise level <35 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 2050VS ½ VS ½ VS ½ VS ½ Dimensions with 3-ay Valve Valve Nominal Dimensions (mm) Size Valve ody COP Inches DN [mm] C 315L 50 ½ [67] 1.73 [44] 1.42 [36] 320L 50 ¾ [78] 1.81 [46] 1.63 [42] 325L [87] 1.81 [46] 1.77 [45] US CND LTIN MEIC / CIEN 29

30 LMX24-MFT-X1, LX24-MFT ctuators, Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. 4 5 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 24 VC line. 1 3 Position 24 VC/DC Transformer ( ) Feedback VDC (+) a 2 lk (1) Common ed (2) Hot ht (3) Y Input Org (5) U Output ZG-01 may be used. 7 8 Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. On/Off control 1 2 lk (1) Common ed (2) Hot to 10 VDC Feedback Signal 7 4 ht (3) Y 1 Input 8 Pnk (4) Y 2 Input Org (5) U Output 2 to 10V MFT Floating Point 1 3 Control Signal 4 to 20 m or 2 to 10 VDC ( ) (+) Ω 500Ω 1/4 watt 6 2 lk (1) Common ht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V 399 MFT VDC/4-20 m PM 1 (C only) 2 Position Feedback VDC ( ) (+) 5 lk (1) Common ht (3) Y Input Org (5) U Output T 399 P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MEIC / CIEN