Installation Method 1: Lays Into the Ceiling Grid. Package Contents

Transcription

1 5731 Benjamin Center Drive Tampa, Florida Phone: Fax: Version: A Release Date: READ THIS MANUAL CAREFULLY AND KEEP IT ACCESSIBLE FOR FURTHER REFERENCE! USE AS DIRECTED: This fixture is intended for installation in accordance with the National Electrical Code and local code specifications. Failure to adhere to these codes and instructions may result in serious injury and/or death. These instructions do not intend to cover all details or variations in equipment, nor to provide for every possible condition related to installation, operation, maintenance, or mounting situation. Should specific problems occur that are not addressed by these instructions, contact your Sales Representative or distributor for assistance. SAFETY INFORMATION Warning: Life-threatening danger due to electric shock, danger of fire and danger from falling objects may exist if the following is not respected! This luminaire must be installed in accordance with the National Electric Code, Canadian Electrical Code, State, provincial, and local regulations by a licensed electrician. When cleaning a fixture, switch off power to the fixture and let it cool completely. Clean the fixture with a soft cloth and water. Never use any cleaner that is not a standard PH neutral detergent. WARNING: DO NOT COVER THE LED PANELS WITH ANY INSULATION MATERIALS OR FLAMMABLE MATERIALS. A Package Contents D 1 Installation Method 1: Lays Into the Ceiling Grid T-Bar B E C Part Description Quantity A U: x Square 1 B U: x Rectangular 1 C Enclosure with LED Driver 1 D E Safety Cables (Square Panel w/4pcs/rectangular Panel w/6pcs) Optional 12 ft. suspension cable kit for hanging below ceiling: #784100U: Square Panel = 2 cables #784101U: Rectangular Panel = 3 cables Electrical Specifications: LED Driver Input: VAC 50/60Hz #711000U Square Input: 2000mA / 18~30VDC #711000U Square = 36W Total Wattage= 43W #711010U Rectangular Input: 1880mA / 28.8~48VDC #711010U Rectangular = 72W Total Wattage = 83W Dimming: The LED power supply has a 3-in-1 dimming functions for use with: 1. a 1-10VDC dimming control 2. a PWM (10V) dimming control 3. A resistance (potentiometer) dimming device. A. #711000U : suitable for installing into a standard 2' x 2' T-Bar lay-in ceiling grid. B. #711010U : suitable for installing into a standard 2' x 4' T-Bar lay-in ceiling grid. C. The ceiling grid must be supported from above with suitable hanger wire or other supports to adequately support the weight of the LED fixture and the LED power supply. D. Tilt the fixture and insert the fixture through an opening in the ceiling grid. E. When the entire fixture is above the ceiling grid, move the fixture into position so the metal frame of the light fixture is flat, level, and equally supported on all four sides by the T-bar grid. WARNING: DO NOT COVER THE LED PANELS WITH ANY INSULATION MATERIALS OR FLAMMABLE MATERIALS. Page 1 of 5

2 0.5 #711000U 0.5 #711010U Page 2 of 5

3 2 Safety Cable Adjustable Side-exit Cable Grip 4 White Supply Wire (Neutral) Black Supply Wire (Line) White Input Wire (Neutral) Knockout LED Driver Input Wire Black Input Wire (Line) T-Bar Screw A. Secure the safety cable to a structural support above the ceiling with the small loop on one end of the safety cable. B. Remove one screw from each of the four corners at the back of the LED panel. Screw one safety cable fitting into each corner of the LED panel. C. Depress the adjustable side-exit cable grip to remove any slack in the safety cable. 3 Red Positive (+) Output Wire (from LED driver) LED Driver in enslosure Black Negative (-) Output Wire (from LED Driver) Crimp Connector or wire nut Ground Wire from Supply Wire Nut Ground Wire from A. Pry up one knockout from the side of the LED driver. Insert the supply wires from ceiling inside of the LED driver. B. By using wire nuts, connect the white supply wire (neutral) to the white input wire (neutral) of LED driver. Connect the black supply wire (line) to the black input wire (line) of the LED driver. Connect the ground wire from supply to the ground wire on the back of the LED panel. C. Secure each wire nut until wires are tightly joined together. Wrap each wire nut connection with approved electrical tape. Red Positive (+) Wire (on the LED panel) Black Negative (-) Wire (on LED panel) 5 Input wires to LED driver LED Driver White Output Dimming Wire (DIM-) from LED driver Blue Output Dimming Wire (DIM+) from LED Driver Wire Nut A. By using wire nuts or crimp connectors, connect the DC output wires of the LED driver to the wires on the fixture. Connect the red positive (+) output wire on the LED power supply to the red positive (+) wire on the LED panel. Connect the black negative (-) output wire of the LED power supply to the black negative (-) wire on the LED panel. B. Secure each wire nut or crimp connector until wires are tightly joined together. Wrap each connection with approved electrical tape. A. Screw wire nut or attach a crimp connector onto each of the unused dimming output wires (blue wire and white wire) on the LED power supply if not connecting a dimming device. These wires are used for dimming functions and need to be capped off with wire nuts if they are not being used. Page 3 of 5

4 6 Short Screw LED Driver Enclosure 4Using the built-in dimming function on power supply cannot turn the lighting fixture totally off. Refer to the connection method below to achieve 0% brightness (full off) of the lighting fixture connecting to the LED power supply unit. Relay Switch Adjuster 0-100k Ohms resistance/ 1-10V DC Voltage/ 10V PWM Signal A. Carefully tuck all wires and connections inside of the LED driver enclosure. Attach the LED driver and enclosure to the top of the LED panel using the four short screws supplied with the enclosure. Hand tighten until snug. Black White AC/L AC/N DIM+ DIM- V(-) V(+) Blue White Black Red LED Lighting Fixture Dimming Function Connection If you wish to use the dimming function, connect the dimming signal wires from a compatible dimming control system to the "DIM+ (blue wire on the LED power supply) and the DIM-" (white wire on the LED power supply). DO NOT connect "DIM- to "-V". Reference resistance values for output current adjustment (Typical) for potentiometer Resistance value Resistance value 10KO 70KO 20KO 80KO 30KO 40KO 90KO 100KO 1-10VDC dimming function for adjustment (Typical) 50KO OPEN 60KO Using a switch and relay can turn the fixture ON/OFF. 1. Output constant current level can be adjusted through output cable by connecting a resistor or 1~10Vdc or 10V PWM signal between DIM+ and DIM-. 2. The LED lighting fixture can be turned ON/OFF by the switch. Adjust the position of the fixture properly and clean the surface of the panel if required with water and soft cloth. After proper installation of the fixture, switch on the AC power to turn on the LED panel. Your installation is now completed and ready to use. Retain this sheet for future reference. Installation Method 2: Suspending below the ceiling (requires the optional suspension cable kit) 1 Dimming value 1V 2V 3V 4V 5V 6V Dimming value 7V 8V 9V 10V OPEN Hole Drill Bit 10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz Duty value Duty value OPEN A. Drill the required hole through ceiling for the toggle bolt. The tolerances of the drill bit used should meet the requirements of ANSI Standard B In denser materials such as high strength concrete, drill the hole #784100U: Suspension cable kit for square LED panel (#711000U) has 2 x 12 L cables and hardware. #784101U: Suspension cable kit for rectangular LED panel (#711010U) has 3 x 12 L cables and hardware. Page 4 of 5

5 R Optional cable kits required for suspending below a ceiling 2 Ceiling cable 5 Suspension cable kits Ceiling cable Threaded Fitting Ceiling Cable Threaded Fitting A. Take apart the ceiling cable support by unscrewing the lower part (threaded fitting) of the ceiling cable support. 3 A. Screw the threaded fitting with steel cable back onto the cable support and hand tighten until snug. 6 Adjustable Side-exit Cable Grip Hole Wing Screw Suspension cable kits Toggle Bolt Ceiling Cable A. Insert the bolt through the ceiling cable support, thread wing onto toggle bolt. Then fold the wing completely back and insert through the drilled hole on the ceiling until the toggle wing springs open. 4 Wing Toggle Bolt A. Pull back on assembly to hold the wings inside the ceiling to prevent the wings from spinning while tightening toggle bolt. Turn the bolt with the screwdriver until firmly tightened. A. #711000U Square : Remove one screw from each of the four corners at the back of the LED panel as shown. Screw two steel suspension cable kits fittings into these holes. This square LED panel requires two suspension cables on each end of the LED panel #711010U Rectangular : Remove one screw from each of the four corners at the back of the LED panel as shown. Remove one screw from each long side of the panel in the center. Screw three steel suspension cable kit fittings into the holes where the screws were removed. This rectangular panel requires three suspension cables. One cable in the center of panel and one cable kit on each short end of the LED panel. B. Depress the adjustable side-exit cable grip to reach your desired hanging height. LED panel should be level. C. Refer to Installation Method 1 (Step 3-6 and the dimming information) to complete the rest installation. Your installation is now completed and ready to use. Retain this sheet for future reference. Page 5 of 5