RC 195 Receiver-Controller
|
|
- Daniel Terence Manning
- 7 years ago
- Views:
Transcription
1 Document No R 95 Receiver-ontroller Product Description The Powers R 95 Receiver-ontroller is a pneumatic instrument that receives one, two or three pneumatic inputs. t produces a pneumatic control signal based on the net pneumatic input and the mechanical settings, such as set point, percent proportional band and authority. Product Numbers Product Number Table. ontrol (Output) Pressure Gauge tick-on cale Dispenser For et Point Dial None English/tandard nternational Units to 0 psig/ 0 to 00 kpa English/tandard nternational Units Troubleshooting efore troubleshooting the operation of the R 95 Receiver-ontroller, ensure that:. The supply pressure at the unit is psi 5 kpa).. All transmitter inputs being used are between to 5 psi ( to 0 kpa).. Only one restrictor supplies each transmitter. 4. The transmitter calibration is correct. Accessories Restriction Repair Kit, includes Four restriction plates and gaskets onnector Kit, includes Two connectors, one -barb and One -barb (for /4 O.D. plastic tubing) R 95 nput Pressure imulators One gauge/switch assembly Two gauge/switch assemblies Three gauge/switch assemblies Terminal trip (for ten /4 O.D. plastic tubes) cale onversion ard (Pkg. of 5) 44-0 et Point Dial heets 95-0 (ee 55-06P5 or the Powers ontrols atalog for scale ranges.) Receiver Gauges a variety of -/ inch (8mm), -/ inch (64mm) and -/ inch (89mm) diameter receiver gauges are available to monitor transmitter input signals. Request GA 4- Receiver Gauges (55-0P5) from your nearest iemens uilding Technologies office. R alibration lide Rule Table. Troubleshooting hecklist. omplaint heck Probable ause orrective Action ontrol pressure stays at approximately zero ontrol pressure stays at approximately supply pressure Rotate set point adjustment screw counterclockwise Rotate set point adjustment screw clockwise Pressure increases Pressure remains unchanged Pressure decreases Pressure remains unchanged Transmitter sensing medium which is above (R.A.) or below (D.A.) the proportional band R 95 out of calibration None Recalibrate Replace Pilot Relay Plugged pilot relay restrictors Restrictors Receiver-ontroller is defective Replace Receiver ontroller Transmitter sensing medium which is above (D.A.) or below (R.A.) the None proportional band R 95 out of calibration Recalibrate Receiver-ontroller is defective Replace Receiver-ontroller Page of 5
2 Document No nstallation General. The R 95 Receiver-ontroller may be mounted in any position on any vertical surface. Two integral mounting tabs accept a No. 8 or No. 0 screw. mall vibrations, such as those from an air handling unit, will not affect the operation of the instrument. over removal The cover furnished with the R 95 is self-locking to the instrument body. To remove the cover, pull cover to the right and lift then pull cover to the left and lift. To put the cover back on, put it in place and press down until it latches.. Generally, /4-inch (6.4mm) O.D. plastic tubing should be used for all the connections to the plug-in air connectors. Larger size tubing will reduce the pressure drops, but they will increase time delays. onversely, smaller tubing will reduce time delays, but will increase pressure drops.. The R 95 requires a clean, dry, oil free supply of compressed air. t is recommended that an AF 908 n-line Air Filter be located in the supply line to the R 95. A maximum of two R 95 Receiver-ontrollers can be supplied by a single AF 908 n-line Air Filter. 4. Whenever possible, the R 95 equipment should be used with a constant air supply. The R 95 Receiver-ontroller and transmitter are calibrated at the factory with a psig air supply. f a constant air supply is not available, use a remote restrictor and separate air supply to transmitters. hanging the supply pressure to the R 95 Receiver-ontroller system from psig to either 8 or 5 psig can shift the control point by as much as % of scale. Once the instrument is secured and proper tubing connections are made, the cover can be removed for access to internal restrictors, percent authority adjustment, percent proportional band adjustment, the set point dial and the set point dial adjustment. Restrictors Figure.. Restrictors are factory installed in all inputs of the Receiver-ontroller. Restrictors are in the "out" position as shipped from the factory. NOTE: When an internal restrictor is required, the restrictor must be moved to the "N" position. Use the following procedure when dialing to a new restrictor position: a. Loosen both screws two full turns. b. ove the restrictor lever back and forth, between the full travel limits, a minimum of two times or until there is no sensation of "drag" against the lever. This will allow the gasket to return to its proper position. c. Retighten both screws with the restrictor lever fully in position against its stop. Do not over-tighten the screws. crews should be tight enough to provide a good seal without warping the restrictor assembly. d. ee Accessories for Replacement Restrictor Kit part number.. When an input is not being used, the restrictor should be in the "OUT" position and the input connection should be open to atmosphere. Page of 5 Figure. Dimensions. iemens uilding Technologies, nc.
3 Document No nstallation, ontinued Figure gives the maximum recommended distances for using the internal restrictor, external restrictor and remote gauges. f the maximum distances are exceeded, there will be excessive pressure drops and time delays which will produce faulty indication and unsatisfactory operation. et point adjustment The output pressure at set point can be adjusted by simply rotating the set point adjustment screw until the desired pressure is reached. The set point dial has a to 5 psi ( to 0 kpa) scale. One of the stick-on scales provided with the unit may be placed on the dial to match the # or # input transmitter range. Each scale is marked D.A. (Direct Acting) or R.A. (Reverse Acting) to match the required action of the receiver-controller. To determine the authority setting, the proportional band setting, and set point setting, refer to the control diagram (or the setting on the instrument being replaced). Technical nstruction R 95- and Application Engineering Form AE 9 gives detailed information on how to calculate the percent proportional band setting, the percent authority setting, and set point conditions. alibration Figure. Proportional band (sensitivity) The proportional band setting is adjustable from to 0% of the primary input scale based on a control pressure change of 5 psi. The proportional band setting selected depends on the characteristics of the system under control; this setting is normally a value which will result in satisfactory control without short cycling (too low percent P) or hunting (too high percent P). Authority adjustment The authority slide provides a means of adjusting the ratio of the change of the # (or #) input pressure to the change of the # input pressure for the same control pressure change. nput connections # and # have fixed authorities with respect to each other equal to 00%. nput connection # has an adjustable authority with respect to inputs # and # which, by means of authority slide, may be varied from 0 to 00%. The authority adjustment is required only when input # is used. Receiver-ontroller imulator A tool designed to simplify the calibration and set-up of the R 95 receiver-controller is available. The R 95 simulators (Product Numbers , and 95-00) can simulate one, two or three transmitters (one-pipe) and indicate their corresponding simulated pressures. Procedure. et the proportional band pointer to value shown on control diagram.. et the authority pointer to value shown on control diagram. R0088R AUTHORTY ADJUTENT ET PONT PERENT PROPORTONAL AND Figure 4. R- ontrol Diagram.. onnect psi supply air to port "". 4. onnect pressure gauge to port "". iemens uilding Technologies, nc. Page of 5
4 D D Document No nstallation, ontinued 5. Apply set point pressures to inputs and, with a screwdriver, turn the set point adjustment screw until control pressure reaches 8 psi (55 kpa) or midpoint pressure between spring range of actuator. 6. alibrate set point dial by pulling it up, turning it to agree with the transmitter input and then releasing it. 7. Turn set point adjustment screw until dial agrees with control diagram. 8. For two input applications, set point conditions are equal to the midpoints of the reset schedule. R0090R A DPONT A References R 95- Operation and adjustment information 55-06P5 AE-9 Application information AE-9 upl Application information GA 4- Receiver Gauges 55-0P5 R 95- R 95 imulators 55-0P5 Figure For manual control point adjustment (PA), connect gradual switch to input or, set switch to 9 psi (6 kpa), and then calibrate controller as in teps 5 through 8 above. alibrating in this manner will allow equal increase or decrease in control point when the bleed type positioning switch is used. 0. Once the sensor-controller system is completely installed and sensor(s) have been calibrated, some tuning of the control loop may be required. f output continuously cycles, increase percent proportional band. f hunting (large offset) is present, decrease percent proportional band. NOTE: Whenever the proportional band or authority settings are changed, the set point dial must be recalibrated. The installation is now complete. Page 4 of 5 iemens uilding Technologies, nc.
5 Document No Receiver-ontroller ross Reference REEVER-ONTROLLER RO REFERENE DRET ATON - NGLE REVERE ATON - NGLE POWER ONTROL DRET ATON - REERVE REET DUAL (ONE REETTNG) DRET ATON - REERVE REET THREE (TWO REETTNG) DENOTE NTERNAL RETRTOR UED DENOTE NTERNAL RETRTOR "OUT" PRARY EONDARY (REETTNG) EONDARY (REETTNG) PRARY FRT REETTNG R - 95 R - 95 HONEYWELL R - 95 R - 95 PRARY EONDARY (REETTNG) PRARY FRT REETTNG RP - 908A (D.A. ODEL) RP - 908A (R.A. ODEL) RP DENOTE ONNETON HA AN EXTERNAL RETRTOR RP EOND REETTNG JOHNON T-900 & T-9005 DRET OR REVERE ATON (ATON DETERNED Y PROGRA ODULE POTON) DENOTE ONNETON HA AN EXTERNAL RETRTOR DENOTE NTERNAL RETRTOR UED DENOTE LOAL ETPONT DENOTE REOTE ETPONT (PA) T-900 ATON DA-DARR RADR DADR RA-RARR PROGRA ODULE DENTFATON T-900 ATON & READJUTENT EONDARY (REETTNG) FRT REETTNG PRARY PRARY EOND T-900 & T-9006 REETTNG T-900 & T-9006 ROERTHAW PRARY EONDARY (REETTNG) EOND REETTNG PRARY FRT REETTNG P4 P4 P4 P4 ARER-OLAN RK TRAN RK TRAN RK - 00 EONDARY (REETTNG) PRARY DENOTE ONNETON HA EXTERNAL RETRTOR RK FRT REETTNG A PRARY EONDARY REETTNG DONTNUED LAND AND GYR POWER R0089R R -85 DENOTE NTERNAL RETRTOR UED R -85 DENOTE ONNETON HA AN EXTERNAL RETRTOR EONDARY (REETTNG) R -85 PRARY R -85 FRT REETTNG PRARY EONDARY REETTNG nformation in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. Powers is a trademark of iemens uilding Technologies, nc. 000 iemens uilding Technologies, nc. iemens uilding Technologies, nc. Landis & taefa Division 000 Deerfield Parkway uffalo Grove, L U..A. Your feedback is important to us. f you have comments about this document, please send them to technical.editor@sbt.siemens.com Document No Printed in the U..A. Page 5 of 5
POWERS CONTROL RC 195 Single Input Receiver-Controller
Document No. 155-119P25 RC 195-4 POWERS CONTROL RC 195 Single Input Receiver-Controller Description The RC 195 Single lnput Receiver-Controller is a pneumatic instrument which receives one pneumatic input,
More informationRC 195 Multiple Input Receiver-Controller
Document No. 129-230 RC 195 Multiple Input Receiver-Controller Product Description The RC 195 Multiple Input Receiver-Controller is a pneumatic instrument that can be used as a one input (DA or RA), two
More informationPowers Controls TH 192 S Single Temperature Room Thermostat
Technical Instructions Document No. 155-065P25 TH 192-1 Powers Controls TH 192 S Single Temperature Room Thermostat 50 60 70 80 TH0355R1 70 80 POWERS Description The TH 192 S thermostats are proportional
More informationPowers Controls Free Energy Band TH 193 HC Heating/Cooling Room Thermostat
Document No. 155-068P25 TH 193-4 Powers Controls Free Energy Band TH 193 HC Heating/Cooling Room Thermostat 50 60 70 80 70 TH0356R1 60 80 POWERS Description The TH 193 HC thermostats are proportional dual
More informationPowers Controls TH 192 HC Heating/Cooling Room Thermostat
Powers Controls TH 192 HC Heating/Cooling Room Thermostat Technical Instructions Document No. 155-066P25 TH 192-2 50 60 70 80 70 TH0356R1 60 80 POWERS Description The TH 192 HC thermostats are proportional
More informationModel 43AP Pneumatic Controller, Style B
Instruction MI 011-476 January 1980 Model 43AP Pneumatic Controller, Style B Installation and Operation Model 43AP Controller continuously detects the difference between a process measurement and its set
More informationGeneral Information... 2
Pneumatic VAV Reset Volume Controllers CSC 2000 Series Applications Guide General Information... 2 CSC 2000 Series Overview...2 odels and Specifications...3 ounting...4 Connections...4 All Units...4 Beige
More informationFahrenheit or Celsius set point dials. Highly sensitive bimetal thermostatic element. Individual field adjustable sensitivity with graduated scale
Powers Controls TH 192 HC Heating/Cooling Room Thermostat Technical l InstructionI TH 192-2 50 60 70 80 70 TH0356R1 60 80 POWERS Des escription Featur ures The TH 192 HC thermostats are proportional single
More informationT-5800-1 and T-5800-2 Single Input Receiver-Controllers Installation and Calibration
T-5800-1 and T-5800-2 Single Input Receiver-Controllers Installation and Calibration 24-7028- 6, Rev. A Technical Bulletin T-5800-1/-2 Issue Date 0316 The T-5800 Series Receiver- Controllers are designed
More informationT-4000 Series Room Thermostat Adjusting Instructions*
Pneumatic Control Manual 717.1 Room Devices Section Technical Bulletin T-4000 Issue Date 0814 T-4000 Series Room Thermostat Adjusting Instructions* The T-4000 Series Pneumatic Room Thermostats are factory
More informationProduct/Technical Bulletin
EP-8000 eries Electro-Pneumatic Transducers convert a voltage or current signal from an electronic controller into a pneumatic output pressure signal. An increase or decrease in the input signal proportionally
More informationT-4000 Series Pneumatic Room Thermostats
T-4000 Series Pneumatic Room Thermostats Pneumatic Control Manual 717.1 Room Devices Section Product Bulletin T-4000 Issue Date 1285 Features Adjustable Sensitivities and Set Points Individual Set Points
More informationRI-215A Operator s Manual. Part Number: 71-0045RK Revision 0 Released: 10/3/05
RI-215A Operator s Manual Part Number: 71-0045RK Revision 0 Released: 10/3/05 Warranty RKI Instruments, Inc., warrants gas alarm equipment sold by us to be free from defects in materials and workmanship,
More informationPNEUMATIC CONTROLS Selection and Description
PNEUMATIC CONTROLS Selection and Description Carnes pneumatic controlled throttling units are suitable for a standard 20 psi control system and may be supplied with pressure dependent or pressure independent
More informationInstallation/ Operation Maintenance
Installation/ Operation aintenance VariTrane Pneumatic Controls arch 02 Thermostat Thermostat election and Location In general, both one- and two-pipe thermostats have a gain of 2.5 psi per degree Fahrenheit,
More informationPart I - Installation
400 Series Pressure and Differential Pressure Switches Types: H400, H402, H403, H400K, H402K, J400, J402, J403, J400K, J402K UNITED ELECTRIC CONTROLS Installation and Maintenance Instructions Please read
More informationSECTION G2: CABLE PROCESSOR MODULE MAINTENANCE
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop
More informationTechnical Instructions Document No. 155-021P25 ET 141-5 September 28, 2004. ET 141 High Limit Control Thermostat. Description.
Document No. 155-021P25 ET 141-5 ET 141 High Limit Control Thermostat Description Application The ET 141 high limit control thermostat is duct mounted and has a rigid bulb, bi-metal rod and tube construction.
More informationWIKA INSTRUMENT CORPORATION
WIKA INSTRUMENT CORPORATION Instruction Manual GAUGE PRESSURE INDICATOR Series 1500 Series 1000 Series 300 WIKA Instrument Corporation 1000 Wiegand Boulevard Lawrenceville, GA 30043 1-888-945-2872 http://www.wika.com
More informationACCUMULATOR INSTALLATION
7001-7 ACCUMULATOR INSTALLATION BRAKE ACCUMULATORS I 308L93 Rae 7-59710 Issued 6-93 Printed in U.S.A 7001-8 Removal ACCUMULATOR VALVE 1. Park the machine on a level surface and lower the. loader bucket
More informationPOWERS Controls No. 4 Pneumatic Damper Actuator
POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000
More informationPRODUCT PROFILE FEATURES
PRODUCT PROFILE Pressure Transmitters & Pneumatic Transducer Airflow Transmitter, Differential Air Pressure Transmitter and Differential & Gauge Liquid/Gas Pressure Transmitter FEATURES AIRFLOW TRANSMITTER
More informationI nstallation. M100Q Series Proportional Actuator with R81Q Controller Board for Thermistor Sensor Applications. Tools Needed.
FANs 268.1, 1628.3 Installation Bulletin M100Q Issue Date 1099 M100Q Series Proportional Actuator with R81Q Controller Board for Thermistor Sensor Applications I nstallation Parts Included M110QGA-1 and
More informationPIEZOMETER AIRFLOW MEASURING RING
PIEZOMETER AIRFLOW MEASURING RING M.K. Plastics is pleased to introduce The Piezometer Airflow Measuring Ring, now available as an accessory for our steel Axijet fans. The system consists of a Piezometer
More informationBristol Series 5453 Indicating Pneumatic Pressure Controllers/Transmitters
July 10, 2007 - Page 1 Bristol Series 5453 Indicating Pneumatic Pressure Controllers/Transmitters General The Bristol 5453-10G indicating pneumatic pressure controller with 624-II control unit, from Emerson
More informationFisher 657 and 667 Diaphragm Actuators
657 and Actuators Product Bulletin Fisher 657 and Diaphragm Actuators Fisher 657 and spring-opposed diaphragm actuators position the valve plug in the valve in response to varying controller or valve positioner
More informationOverview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer
Overview READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION PARTS LIST A. Flush valve B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve
More information8900 EMR (WITH DETECTOR)
00 EMR (WITH ) GENERAL DESCRIPTION Each 00 EMR series unit contains a door closer, hold open electromagnet and smoke detector. The unit can be used as a single installation or as a series of singles powered
More informationFleck 4650. Service Manual INSTALLATION AND START-UP PROCEDURE TABLE OF CONTENTS JOB SPECIFICATION SHEET
Fleck 4650 Service Manual TABLE OF CONTENTS JOB SPECIFICATION SHEET...1 INSTALLATION AND START-UP PROCEDURE...1 CONTROL VALVE DRIVE ASSEMBLY...2 CONTROL DRIVE ASSEMBLY FOR CLOCK...3 BYPASS VALVE ASSEMBLY...4
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More informationElectro-pneumatic control valves
Electropneumatic control valves 7 Miniature solenoid valves for alternating current Conform to the Low Voltage Directive or mounting on subbase or footprint in accordance with CNOMO recoendation E 066120N
More informationDissolved Oxygen Sensors
Instruction Sheet PN 51A-HxDO/rev.F June 2008 Models Hx438 and Gx448 Dissolved Oxygen Sensors For additional information, please refer to the Instruction Manuals CD shipped with this product, or visit
More informationInstallation Manual. TITUS I, II, and IIA Pneumatic Controls Installation, Operation, and Maintenance Manual. (See Figure 3) (Label, See Figure 3)
Installation Manual PNEU-IOM-1.0 5-2-05 IUS I, II, and IIA Pneumatic Controls Installation, Operation, and Maintenance Manual Adjusting Minimum and Maximum Air Flow Airflow limits are printed on the label
More informationValve systems Base plates, according to standard ISO 5599-1. Brochure
ISO 5599-1 Brochure 2 ISO 5599-1 Single subbase Single subbase, thread connections on the side standard: ISO 5599-1 Frame size: ISO 1 - ISO 4 compressed air connection output: G 1/4 - G 1 Reversed pressure
More informationInstallation and User Instructions Unvented Electric Storage Water Heater Models: S10UNV, S15UNV.
Installation and User Instructions Unvented Electric Storage Water Heater Models: S10UNV, S15UNV. MULTIPOINT Please read and understand these instructions before starting work. Please leave this leaflet
More informationDTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual
DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR Installation and Operation Manual 1 ENGLISH Safety Instructions 2 Features 2-3 Specifications 3 Installation 4-5 Wiring Diagrams 6-7 Warranty 8
More informationG1/4 Q8. Standard with biased position
Contents Version Actuation Page Characteristics Dimensions x / Way Valves pneumatic 6,7, 0 9 electric 6,7 9, 9 / Way Valves pneumatic 6,7, 0 electric 6,7, 0 / Way Valves pneumatic 6,7,, 6, 7 electric 6,7,,
More informationSELECTION, APPLICATION AND MAINTENANCE
DIESEL PROTECTION SYSTEMS Automatic Diesel Engine Shut Down System for Safe Area Applications SELECTION, APPLICATION AND MAINTENANCE Series 300 Series 310 SYSTEM DESCRIPTION Suitable for attended engine
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
More informationSELECTION, APPLICATION AND MAINTENANCE
DIESEL PROTECTION SYSTEMS D-Series Engine Automatic Overspeed Shut Down Valves (Spindle Types with Air Pressure and Manual Shut Down Options) SELECTION, APPLICATION AND MAINTENANCE Valve Numbers D92-AP
More informationProduct Manual. CVS Type 67AFR Filter Regulator. Introduction. Installation. Description
Product Manual CVS Type 67AFR Filter Regulator Introduction This CVS Controls product manual includes instructions for the installation, adjustment, maintenance and parts ordering of the CVS Type 67AFR
More informationTypical Aluminum GFM Mass Flow Meter
MASS FLOW METERS Design Features n Rigid metallic construction. n Maximum pressure of 1000 psig (70 bars). n Leak integrity 1 x 10-9 of helium. n NIST traceable certification. n Built-in tiltable LCD readout.
More informationP7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc
P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center
More informationHOW TO ORDER SAFETY PRODUCTS/SAFETY CONTROL SYSTEMS ELECTRICAL SAFETY CONTROLS
HOW TO ORDER SAFETY PRODUCTS/SAFETY CONTROL SYSTEMS PNEUMATIC SAFETY CONTROLS BASIC CONTROLS SC3000 - SELF CONTAINED 2 HAND CONTROL - STAND ALONE MODEL SC3300 - SELF CONTAINED 2 HAND CONTROL - PRESS READY
More informationInstallation Instructions
page 1 of 7 Description These feeds are designed for installation in shielded standard types of parabolic antennas. The feed is designed for positive metal-to-metal contact between the feed and the reflector,
More informationIMPORTANT DOCUMENTATION DO NOT DISCARD!
PART NO.: 6441-263C SERIES GRT 3 JAW PARALLEL GRIPPERS INFORMATION SHEET IMPORTANT DOCUMENTATION DO NOT DISCARD! Use this information sheet to assist with gripper installation and setup. File with maintenance
More informationInstallation Operation Maintenance Troubleshooting Version 2.1, Apr/09
Installation Operation Maintenance Troubleshooting Version 2.1, Apr/09 1402 Congratulations! All of us at Summit Dental Systems want you to know that your 1402 Delivery Unit has been built with the finest
More informationDPT-2015 Differential Pressure Transmitter for VAV Box Applications
FANs 216, 1628.3 Product/Technical Bulletin DPT-2015 Issue Date 1298 DPT-2015 Differential Pressure Transmitter for VAV Box Applications The DPT-2015 Differential Pressure Transmitter senses differential
More informationABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions
4057250/8 IM-P405-16 AB Issue 8 ABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Operation
More informationM A N U A L 13-10-05
Documentation The following information sheets illustrate the description below: 12-WW01-4G-E Sectional view of the lance with main dimensions 12-W101-6G-E Sectional view of the head of the lance with
More informationCONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version)
TECHNICAL DATASHEET #TD1102AX CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (4-20 ma Input Version) Part Number: Connector Amplifier CAPV-H-4-20MA-x complete with cable CAPV-4C-yM Where: x = current output
More information2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net
Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.
More informationInstruction Manual. A50099 Calibration Device. www.band-it-idex.com TIE-DEX CALIBRATION DEVICE A50099
Instruction Manual TIE-DEX CALIBRATION DEVICE Introduction: The Tie-Dex is to be used with the A30199, A40199, A35199, and A35599 Tools using BAND-IT Tie-Dex ties only. Table of Contents: 1. Introduction
More informationProportional pressure regulators VPPE
Proportional pressure regulators VPPE Proportional pressure regulators VPPE Product range overview Function Version Pneumatic connection Proportional pressure regulator Nominal size for pressurisation/
More informationModels SFP33 & SFP32 Pressure Transmitters
SFP33 Flow-Through Pressure Transmitter SFP32 Single-Ended Pressure Transmitter DS-PR-SFP-eng April, 2016 Data Sheet Models SFP33 & SFP32 Pressure Transmitters Pressure Brooks Seal Free Pressure Measurement
More informationYour safety and the safety of others are very important.
NATURAL GAS TO PROPANE CONVERSION KIT 090 INSTALLATION INSTRUCTIONS FOR ALTITUDES 0 -,00 FT. ONLY PROPANE CONVERSION KIT SAFETY... INSTALLATION REQUIREMENTS... Tools and Parts... LP Gas Requirements...
More informationSpeed-Mat Rectangle Cutter
Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.
More informationOceanscience Cable Chimp II Cableway ROV System User Guide and Warranty
Oceanscience Cable Chimp II Cableway ROV System User Guide and Warranty Page 1 Table of Contents Introduction Page 3 Overview Page 3 Setup and Operation Page 5 Remote Control Page 6 Power Management Page
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate
More information5800 Temperature Sensor Cable Assembly
5800 Temperature Sensor Cable Assembly Removal and Replacement Instruction Sheet #60-4702-070 Revision D, January 14, 2013 Overview The 5800 has two refrigeration temperature sensors, one attached to the
More informationHinge Replacement & Hinge and Hardware Adjustment Guide for Andersen Frenchwood Hinged Patio Doors Manufactured Before November 2005
Hinge Replacement & Hinge and Hardware Adjustment Guide for Andersen Frenchwood Hinged Patio Doors Manufactured Before November 2005 For ease of installation and continued enjoyment of your Andersen product,
More informationSKP Series SKP15U.. Gas Valve Actuator with Safety Shutoff Function
SKP Series SKP15U.. Gas Valve Actuator with Safety Shutoff Function Document No. 155-751 SKP15U.. Description Only when assembled to Series VGU Gas valves SKP15 electro-hydraulic actuators combine with
More informationWater valves REFRIGERATION AND AIR CONDITIONING. Fitters notes
REFRIGERATION AND AIR CONDITIONING Fitters notes Contents Page Application...3 Identification...3 Installation...5 Setting...6 Maintenance...6 Spare parts...8 Fault location...9 2 RZ4DA202 DKRCC.PF.D00.A1.02
More informationTriac Printed Circuit Board Replacement
Technical Service Bulletin: Triac Printed Circuit Board Replacement TRONIC 5000C Pro Models: WH17, WH27, WH36 Introduction Fig. 1 ELECTRICITY IS EXTREMELY DANGEROUS. TAKE EXTRA PRECAUTIONS AND ENSURE ALL
More informationUnit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 4 DIRECTIONAL CONTROL VALVES The material needed for outcome 2 is very extensive
More informationTrace Dissolved Oxygen Sensor
Instruction Sheet PN 51A-499ATRDO/rev.G September 2010 Model 499A TrDO Trace Dissolved Oxygen Sensor For additional information, please visit our website at www.emersonprocess.com/raihome/liquid/. CAUTION
More informationwith MERCURY FREE 1 HP Relays ! WARNING Before using this product read and understand instructions.
B Installation & Maintenance Instructions MM-414 Series 150E and 157E Low Water Cut-Off/Pump Controllers For Steam Boilers and Other Level Control Applications A Typical Applications: Primary or secondary
More informationPC1131 Electric Air Compressor
Senco Products Inc. 8485 Broadwell Road Cincinnati, Ohio 45244 PC1131 Electric Air Compressor Operating Instructions 2006 by Senco Products, Inc. Warnings for the safe use of this tool are included in
More informationSIMPLEX UNICAN LOCKS CHANGING THE CODE / COMBINATION 900 Series 1000 Series L1000 Series LP1000 Series EE1000 Series 2000 Series 2015 Series
SIMPLEX UNICAN LOCKS CHANGING THE CODE / COMBINATION 900 Series 1000 Series L1000 Series LP1000 Series EE1000 Series 2000 Series 2015 Series 2400/2500 Series 3000 Series 3100 Series Simplex 5000 Series
More informationIndex 11.1. Page. Pumping Systems...11.2-11.4 Intensifiers...11.5 Gas Boosters...11.6-11.7 High Pressure Generators...11.8-11.9
Pumping Systems, Intensifiers, Gas Boosters and High Pressure Generators High Pressure Equipment Company produces a number of components and systems for general industrial, elevated pressure applications.
More informationTraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions
TraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions TRACETEK TraceTek TTDM Replacement Parts General Information These instructions detail the steps to
More informationOEM Manual MODEL 2350 ELECTRONIC DUAL CYLINDER SCALE
OEM Manual MODEL 2350 ELECTRONIC DUAL CYLINDER SCALE Scaletron Industries, Ltd. Bedminster Industrial Park 53 Apple Tree Lane P.O. Box 365 Plumsteadville, PA 18949 USA Toll Free: 1-800-257-5911 (USA &
More informationPRESSURE REDUCING CONTROL VALVE
Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING CONTROL VALVE with LOW FLOW BY-PASS FEATURE Main Line
More informationGenStore Archive Cabinet
GenStore Archive Cabinet Setup and Maintenance Manual Version A April 2014 Two GenStore Archives shown mounted on optional table stand. 2 Contents Getting Started... 4 Using this Manual...4 Safety Precautions...4
More information20000068 WIRELESS REMOTE ASSEMBLY, 24VDC, 1 TRANS,1 REC
20000068 WIRELESS REMOTE ASSEMBLY, 24VDC, 1 TRANS,1 REC Fitment to MP-25 620 CR 4841, Haslet, TX 76052 Ph 817.439.1108 Fax 817.636.5675 www.machine-technologies.com Kit contents 1 Transmitter 2 button,
More informationMustang Series PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE. M115-2 (Globe) M1115-2 (Angle) Schematic. Standard Components
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Throttles to maintain minimum upstream pressure PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE
More informationWebinar Series. Committee. Disc Brake Wheels Off Inspection and Reline. Presents
1 APTA Bus Webinar Technical Series Maintenance Committee Webinar Series Presents Disc Brake Wheels Off Inspection and Reline January 21, 2015 2 Introduction Welcome to today s webinar in which we will
More informationMP8000 Series Pneumatic Valve Actuators
14-1161- 9, Rev. A Technical Bulletin MP8000 Issue Date March 2016 MP8000 Series Pneumatic Valve Actuators Pre-Assembly Details Page 3 MP8000 Actuator Components 3 Tools Required to Assemble an MP8000
More informationSelection Chart T-4000 Series Accessories (Part 1 of 5) Code Number Figure Description Application (High or Low Volume)
Code No. LIT-1921710 Issued July 25, 2011 T-4000 Series Accessories Selection Chart T-4000 Series Accessories (Part 1 of 5) ( or Volume) F-100-20 F-300-30 F-300-34 F-300-31 F-300-35 F-500-45 F-300-30 Coupler,
More informationLINDGREN-PITMAN, INC. Super Spool III Installation Instructions
LINDGREN-PITMAN, INC. Super Spool III Installation Instructions LINDGREN-PITMAN, INC. 2615 N.E. 5th Avenue * Pompano Beach, Florida 33064 * U.S.A. (954)943-4243 * (954)943-7877 Fax E-mail: longline@gate.net
More informationMP-4V Heavy Duty Riveter / 39048
MP-4V Heavy Duty Riveter / 39048 This newly designed heavy-duty air/hydraulic riveter is ergonomically designed with the professional in mind. The light weight 3.7 lbs. well balanced MP-4V includes a Vacuum
More informationSubmersion/Insertion Toroidal Sensor
Instruction Sheet PN 51A-228/rev.P December 2010 Model 228 Submersion/Insertion Toroidal Sensor For additional information, please visit our website at www.emersonprocess.com/raihome/liquid/. CAUTION SENSOR/PROCESS
More informationKNC Model 3666 Automatic Pressure Calibration System
KNC Model 3666 Automatic Pressure Calibration System Product Description The Model 3666 Automatic Pressure Calibration (APC) System by King Nutronics Corporation is a portable secondary standards laboratory
More informationPTU Series Ultrahigh-Purity Pressure Transducers
PTU Series UltrahighPurity Pressure Transducers User s Manual The Swagelok PTU series pressure transducer provides electronic monitoring of system pressure for ultrahighpurity applications. The PTU series
More informationMany Products...One Source
PRESSURE GAUGES Dedicated Sales Rep for Your Area 97%Fill Rate Shipping within 24 Hours State of the Art Warehouse System Technical Support Quality Control Program 25 Whaley Avenue Milverton, Ontario N0K
More informationPC1130 Electric Air Compressor
Senco Products Inc. 8485 Broadwell Road Cincinnati, Ohio 45244 PC1130 Electric Air Compressor Operating Instructions 2006 by Senco Products, Inc. Warnings for the safe use of this tool are included in
More informationGlobal Water Instrumentation, Inc.
Global Water Instrumentation, Inc. 11390 Amalgam Way Gold River, CA 95670 T: 800-876-1172 Int l: (916) 638-3429, F: (916) 638-3270 6 Tipping Bucket: RG200 02/05/10 01-343 - 1 - Congratulations on your
More informationTyan Computer. Transport PX22. Service Engineer s Manual
Tyan Computer Transport PX22 Service Engineer s Manual 1 Precaution To read through the user manual, check all assembly and follow setup process before any operation on this server To keep paper clips,
More informationSTEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER
14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------
More informationInstallation Instructions 6028.801
DAZZLE Installation Instructions 08.80 Spread Lavatory Faucet with Speed Connect Drain* Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American
More informationTool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014. 0414/Rö
Tool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014 0414/Rö Disclaimer The illustrations in this documents may deviate from the delivered product. We reserve the right to make changes due to errors
More informationT-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5. www.thomsonlinear.com
T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5 www.thomsonlinear.com Version History Edition Number Edition Date Reason for Revision 1 2004 First edition
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
More informationData sheet Radiator Thermostats type RA 2000 Valve bodies type RA-FN and RA-G
Data sheet Radiator Thermostats type RA 2000 Valve bodies type RA-FN and RA-G EN 215-1 HD 1215-2 Application RA 2910 built-in sensor RA 2920 tamperproof RA 5062 remote sensor temperature adjuster RA-FN
More informationTS93 EMR T/PT/TDE. Surface applied door closer
TS EMR T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer with smoke detector (EMR T) Push side track mount door closer with smoke detector (EMR PT) Double
More informationCDS TROUBLESHOOTING SECTION I. VACUUM. 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg)
CDS TROUBLESHOOTING SECTION I. VACUUM 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg) 1.1. Clogged hoses or wand tube. Disconnect hoses and carefully check for an obstruction. 1.2. Excessive
More informationVP23, 3-way proportional pressure control valves Seat valve with μp-driven pressure control
VP, -way proportional pressure control valves > > Port size: G/... G/ > > All-digital control electronics > > Variable pressure control > > Optional actuation via fieldbus (separate datasheet on request)
More informationAIR CHAMP PRODUCTS. User Manual SE BRAKE MODELS: SE-100-1, SE-200-1, SE-500-1, and SE-1000-1 1 FORM NO. L-20084-H-0814
AIR CHAMP PRODUCTS User Manual SE BRAKE MODELS: SE-100-1, SE-200-1, SE-500-1, and SE-1000-1 1 FORM NO. L-20084-H-0814 In accordance with Nexen s established policy of constant product improvement, the
More informationSIMPLIFIED VALVE CIRCUIT GUIDE
NA-09 FLOW CONTROL METERED- FREE FLOW UT OUT CYLDER TENDED SOLENOID NO. A Guide to Understanding Pneumatic Directional Control Valves SIMPLIFIED CIRCUIT GUIDE 0 0 0 0 Compressed Air Valves Directional
More informationASSEMBLY MANUAL SE-4S35
Automatic drive ASSEBLY ANUAL SE-4S35 AI-4S35 SG-4R35 Battery box otor unit Inter-4 hub CONTENTS WARNING 1 INSTALLATION CONITIONS Battery box Speed sensor Cable lengths and diameters otor unit Recommended
More information