Installation E19-310AC. Combination Drench Shower/Eye/Face Wash. Table of Contents

Size: px

Start display at page:

Download "Installation E19-310AC. Combination Drench Shower/Eye/Face Wash. Table of Contents"

Percival Wells
7 years ago
Views:

1 Combination Drench Shower/Eye/Face Wash Table of Contents Pre- Information Instructions Assembly of Components Parts List ACE Rev. H; EN 06-3F 007 Bradley Corporation Page 1 of 6//07 P.O. Box 309, Menomonee Falls, WI USA PHONE BRADLEY FAX (6) 1-817

2 R Datum Signe P.O. BOX 309, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) WARNING Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department. Compliance and conformity to drain requirements and other local codes and ordinances is the responsibility of the installer. P.O. Box 309, Menomonee Falls, WI 301 TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Unterschrift THIS SIDE UP! Packing List Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Flush the water supply lines before beginning installation and after installation is complete. Test the unit for leaks and adequate water flow. Main water supply to the eyewash should be ON at all times. Provisions shall be made to prevent unauthorized shutoff. The ANSI Z38.1 standard requires an uninterruptible supply of flushing fluid at a minimum 30 PSI (0.1 MPa) flowing pressure. Flushing fluid should be tepid per ANSI Z38.1. The inspection and testing results of this equipment should be recorded weekly to verify proper operation. This equipment should be inspected annually to ensure compliance with ANSI Z38.1. Workers who may come in contact with potentially hazardous materials should be trained regarding the placement and proper operation of emergency equipment per ANSI Z38.1. For questions regarding the operation or installation of this product, visit or call BRADLEY. Product warranties may also be found under Product Information on our web site at 6//07 Bradley Corporation 1-163ACE Rev. H; EN 06-3F

3 Supplies Required: (3) M10 floor anchors and bolts Teflon tape and pipe sealant Piping to 1-1/4" BSP water supply inlet on unit Adequate supply pipe supports Piping to 1-1/4" BSP drain outlet for eyewash Minimum 10mm (4") drain to accommodate 11 liters (30 gallons) per minute discharge for drench shower waste. OPTIONAL: sign-mounting hardware Step 1: Secure base to floor 1. Install three suitable anchors (by installer) for M10 bolts in the floor (see Figure 1).. Bolt the base to the floor anchors using M10 bolts (supplied by installer). IMPORTANT: Some teflon sealants may cause stress cracks in the plastic showerhead leading to failure. Use teflon tape for sealing the showerhead. Step : Assemble components 1. Assemble the remaining unit components as shown in Figure, page. Apply pipe sealant or tape (supplied by installer) to all male-threaded pipe joints. Use the rubber grip pad provided or a strap wrench around pipes when tightening to prevent marring. Place the grip pad on the pipe, then put the wrench over the grip pad and turn the pipe with the wrench. Bottom edge of showerhead should be 160mm (7'-1") from floor.. Connect the steel chain to foot treadle S hook. Then with foot treadle raised up, straighten chain and connect a link to S hook on valve handle. Make sure steel chain is pulled tight. The length of chain used will vary. Step 3: Connect water supply Use Teflon Tape Only 133mm (-1/4") 160mm (7'-1") to Floor NOTE: Figure 1 Ø 4mm (10") Ø 73mm (10-3/4") 9mm (9") 67mm (10-1/") 64mm (-3/8") 610 mm (4") 41mm (9-1/") 1mm (6") Top View From Bowl 16mm (6-1/") 1041mm (41") 1676mm (66") to Floor Ø 9mm (9") Flange with (3) Ø 10mm (3/8") Holes on Ø 03mm (8") Bolt Circle All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 3mm (1/8") per threaded joint. To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by 3mm (1/8"). IMPORTANT: Do not rely on Bradley s Combination Unit to support supply piping. 1. Connect water supply piping to the 1-1/4" BSP inlet on the unit (piping supplied by installer). Provide adequate supports (supplied by installer) for the pipe using pipe hangers or other means.. Connect the drain piping to the 1-1/4" BSP drain outlet on the unit (piping supplied by installer). 3. Hang the safety sign from the unit with the curtain hooks provided (or mount it to the wall using sign-mounting hardware supplied by installer). Bradley Corporation 1-163ACE Rev. H; EN 06-3F 6//07 3

4 P.O. BOX 309, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) R P.O. Box 309, Menomonee Falls, WI 301 TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Datum Unterschrift Signe Assembly of Components /4" BSP Supply Inlet (BSP noted with black NOTE: If tee (Item 7) is line on threads) used as a supply inlet, use plug on tee (Item ) /4" BSP Supply Inlet (BSP noted with black line on threads) NOTE: Use teflon tape only NOTE: Items come preassembled as Item 4. Items come preassembled as Item 10. Items come preassembled as Item 14. Items come preassembled as Item /4" BSP Drain Outlet Figure //07 Bradley Corporation 1-163ACE Rev. H; EN 06-3F

5 Parts List Item Part No. Qty Description Item Part No. Qty Description Base B Pipe Tee 1-1/4" NPT LC 1 Pipe 1-1/4" NPT x 706mm 4 S Europe Eyewash Sub-Assy Pipe Tee 1-1/4" NPT 4. S Plugged Nipple 1-1/4" NPT x 76mm Reducing Tee Street Elbow Union 1/" Female NPT QX 1 Pipe 1-1/4" NPT x 16mm 4.8 S /" Ball Valve with Nut Jam Nut only DA 1 Lockwasher Pipe Elbow 1-1/4" NPT LE 1 Pipe Nipple 1-1/4" NPT x 83mm A 1 Drain Inlet/Outlet LQ 3 Pipe 1/" NPT x 86mm LW Pipe 1-1/4" NPT x 79mm Pipe Plug 1-1/4" NPT B 1 Reducing Tee w/ BSP end LL 1 Pipe 1" NPT x 34mm Curtain Hook 10 S Stay-Open Ball Valve 1" NPT DC 1 Lockwasher Handle 10.3 S " Ball Valve with Nut Jam Nut only Stop Bracket Washer, Friction LK 1 Pipe 1" NPT x 310mm A 1 Pull Rod - 4" Long 14 S Plastic Showerhead Assy Showerhead Shell Diffuser Screw 1 S Handle Assy. 16 S HFO Prepack Lever Arm "S" Hook D 1 Stainless Steel Chain Treadle Screw Acorn Nut Eye Bolt BT 1 Lockwasher Hex Nut Friction Washer 17 S Cup/Strainer Prepack Center Seal Gasket Cup Strainer Supply Pipe 18 E0-064D 1 EFW Assy S0-091P 1 Eyewash Yoke 18. S0-13 EFW Sprayhead 18.3 S3-063 Dust Cover Assy S.S. Eyewash Receptor E 1 Safety Sign Emergency Tag Grip Pad (not shown) R 1 Adapter Street Elbow 1" NPT Bradley Corporation 1-163ACE Rev. H; EN 06-3F 6//07

Installation E19-310. Combination Drench Shower/Eyewash. Table of Contents

Installation E19-310. Combination Drench Shower/Eyewash. Table of Contents Installation E19-310 Combination Drench Shower/Eyewash Table of Contents Pre-Installation Information...................... Installation Instructions.........................3 Assembly of Components.......................