IP Link Device Interface Communication Sheet
|
|
- Rosalind Hill
- 7 years ago
- Views:
Transcription
1 yeahthis document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete operating instructions, refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation. Device Specifications: Device Type: Audio Processor Manufacturer: Biamp Firmware Version: Model(s): Nexia Version History: Driver Version Date IP Link Compiler IP Link Firmware GC2 Version 10 07/06/ /26/ Notes Changed the Dial Keypad command to send out individual numbers to the Nexia TC instead of buffering them first. Added TX/RX Mute commands for the corresponding Transmit/Receive blocks. Added asterisk and pound buttons to the dialer. Added more detailed configuration instructions. 7 12/02/ Added phone commands for the TC model. 6 8/28/ /09/ Extron Certified. Modified volume status polling. Tested on a Nexia CS. Extron Certified. Added Instance ID Letters. Modified connection status monitoring. Added channel selection. Tested on a Nexia CS. 4 5/23/ Added Scaled Volume command. 2 4/11/ Added support for Instance ID tags. 1 10/30/ Initial version. Page 1 of 6
2 Driver Notes: This driver is not supported by the MLC62. Nexia uses an Instance ID number to specify the exact DSP block to be controlled. Custom names (Instance ID s) may be assigned to DSP blocks, and used in lieu of Instance ID numbers within NTP (Nexia Text Protocol) command strings. Instance ID s may be up to 32 characters, but may not start with a number. If the Instance ID includes spaces, it must be double-quote delimited ("Instance ID ") when used in a command string. The Instance ID number (and Instance ID ) can be found by first making sure the Properties attribute of a control block is enabled by right-clicking the DSP block and selecting "Properties". Then hover over the Property Sheet tab on the left and both identifiers are available in the DSP Attributes 1 tab. To simplify instance ID tag naming within the driver, a capital letter and a number are used as the Instance ID for a variety of control blocks. The following Nexia configuration blocks correspond to the following driver commands: Command Name Letter Range Corresponding Nexia Control Block Auto Answer A 1 ~ 16 TC - Receive (Double Click) Dial Keypad D 1 ~ 16 TC - Dialer (Double Click) Logic State L 1 ~ 32 Logic State Mute M 1 ~ 32 Mute Phone Input Level I 1 ~ 16 TC - Receive And Receive Mute Phone Output Level O 1 ~ 16 TC - Transmit and Transmit Mute Preset Recall N/A N/A Preset Button Hook D 1 ~ 16 TC Dialer (This logic resides in the Dialer block, use this command to hang up. Redial R 1 ~ 16 TC - Dialer Rdl Node Scaled Volume V 1 ~ 16 Level Speed Dial S 1 ~ 16 TC - Dialer Nodes 1-16 Volume V 1 ~ 16 Level Page 2 of 6
3 For example, if you just wanted to control the volume of two channels on a Nexia CS device, your Nexia configuration would look like this: A corresponding GC2 configuration could look like this: Page 3 of 6
4 Control Commands & States: Auto Answer 0-5 Auto Answer Instance ID 1-16 Dial Keypad 0-9 Dial Redial * # Pause Clear Dial Keypad Instance ID 1-16 Hook On Off Logic State 0 1 Logic State Channel 1-16 Logic State Instance ID 1-32 Mute On Off Mute Channel 1-16 Mute Instance ID 1-32 Phone Input Level Up Down Phone Level Instance ID 1-16 Phone Output Level Up Down Preset Recall 1-32 Receive Mute On Off Redial Instance ID 1-16 Scaled Volume -100 ~ 12 at 1 db Speed Dial 1-16 Speed Dial Instance ID 1-16 Transmit Mute On Off Volume -100 ~ 12 at 0.5 db Volume Instance ID 1-32 Page 4 of 6
5 Status Available: Connection Status Connected Disconnected Hook On Off Logic State 0 1 Mute On Off Receive Mute On Off Transmit Mute On Off Volume -100 ~ 12 at 0.5 db Page 5 of 6
6 Cable and Adapter Requirements: M/F RS-232 Straight Serial Cable (Extron Electronics P/N XX) Notes for the Device: Serial communication: Port Type: Baud Rate: Data Bits: RS232 Parity: None Stop Bits: 1 8 Flow Control: None Pin Assignments Diagram: Note: Captive screw connector may also be used as a serial connection. General Notes: Page 6 of 6
IP Link Device Interface Communication Sheet
This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete
More informationIP Link Device Interface Communication Sheet
This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete
More informationIP Link Device Interface Ethernet Communication Sheet
This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete
More informationIP Link Device Interface Ethernet Communication Sheet
This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete
More informationHow To Wire An Extron Ip Link Device To A Cell Phone With A Sim Sim Sim Card (Ipl) For A Sim Card With A Power Adapter (Iphones) For An Extravoy) For Free (For A Simio)
poly_5_6486_1.pkn Revision: 4/1/013 This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme
More informationIP Link Device Interface Ethernet Communication Sheet
This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete
More informationIP Link Device Interface Ethernet Communication Sheet
This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete
More informationQUICK START GUIDE. Configuring Biamp s Dialer Application INTRODUCTION CONFIGURE THE DEVICE S WI-FI SETTINGS CREATE A NEW ROOM
Configuring Biamp s Dialer Application INTRODUCTION Biamp now offers an app for Apple ipad /iphone /ipod touch which allows you to wirelessly control an AudiaFLEX or a Nexia TC installed in a teleconferencing
More informationIP Link Device Interface Ethernet Communication Sheet
This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete
More informationSYMETRIX SOLUTIONS: TECH TIP August 2015
String Output Modules The purpose of this document is to provide an understanding of operation and configuration of the two different String Output modules available within SymNet Composer. The two different
More information1. Make sure that no client accounts are open. 2. Click on Setup, then click Modem. The Modem Setup window will appear.
SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS WINLOAD MODEM SETUP The modem setup is a very important step in the connection process. If the modem setup is not properly completed communication between
More informationSYMETRIX SOLUTIONS: TECH TIP February 2014
Crestron Symetrix Dialer Example Introduction This tech-tip describes how to control a Symetrix Radius AEC and telephony interface using a Crestron Pro2-style controller. A complete Symetrix Radius configuration
More informationProgramming and Using the Courier V.Everything Modem for Remote Operation of DDF6000
Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000 1.0 Introduction A Technical Application Note from Doppler System July 5, 1999 Version 3.x of the DDF6000, running version
More informationKnowledge Base Article. Integrating ISONAS Access Control System with TagMaster LR-series RFID Readers
Knowledge Base Article Integrating ISONAS Access Control System with TagMaster LR-series RFID Readers Copyright 2009-2012, ISONAS Security Systems All rights reserved Table of Contents 1: INTRODUCTION...
More informationHow To Connect A Directsofl To A Powerpoint With An Acd With An Ctel With An Dm-Tel Modem On A Pc Or Ipad Or Ipa (Powerpoint) With A Powerline 2 (Powerline
Application Note Last reviewed: 03/17/2008 AN-KEP-003.doc Page 1 of 23 Introduction... 1 Recommended s and ports to use... 1 Cable Wiring... 2 MDM-TEL Configuration ( Wizard)... 3 Direct Logic Communications
More informationSmarthome SELECT Bluetooth Wireless Stereo Audio Receiver and Amplifier INTRODUCTION
Smarthome SELECT Bluetooth Wireless Stereo Audio Receiver and Amplifier INTRODUCTION The Smarthome SELECT Bluetooth Wireless Stereo Audio Receiver and Amplifier is a multi-functional compact device. It
More informationAquadyne TechTip TITLE: TROUBLESHOOTING PC COM PORT AND MODEM PRODUCTS AFFECTED SYMPTOMS POSSIBLE CAUSES
Aquadyne TechTip TITLE: TROUBLESHOOTING PC COM PORT AND MODEM COMMUNICATIONS WITH AN OCTOPUS. Article # 072297-1 Last reviewed: 03/25/98 Keywords: Serial Port, Modem, Polling, AquaWeb, Node Not Responding
More informationAccessing Diagnostics using a Dialup Modem
Purpose This application note is meant to guide a user through the setup and use of a dial-up modem to retrieve diagnostics data from a remote master. Equipment Used This application note was written specifically
More informationTo perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:
PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,
More informationIntroduction: Implementation of the MVI56-MCM module for modbus communications:
Introduction: Implementation of the MVI56-MCM module for modbus communications: Initial configuration of the module should be done using the sample ladder file for the mvi56mcm module. This can be obtained
More informationUsing HyperTerminal with Agilent General Purpose Instruments
Using HyperTerminal with Agilent General Purpose Instruments Windows HyperTerminal can be used to program most General Purpose Instruments (not the 531xx series counters) using the RS-232 Serial Bus. Instrument
More informationConnecting and Setting Up Your Laptop Computer
CHAPTER 3 Connecting and Setting Up Your Laptop Computer This chapter explains how to connect your laptop to the Cisco Unified MeetingPlace system and how to set up your laptop so that you can use HyperTerminal.
More informationACU-1000 Manual Addendum Replacement of CPM-2 with CPM-4
ACU-1000 Manual Addendum Replacement of CPM-2 with CPM-4 1 PURPOSE:... 1 2 CPM-4/CPM-2 COMPATIBILITY... 2 2.1 NETWORK CABLES... 2 2.2 FACTORY DEFAULT SETTINGS... 2 2.3 CHANGING THE RS-232 SERIAL PORT BAUD
More informationSECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS. Quick Start Instructions
TM SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS Quick Start Instructions Introduction WinLoad for Windows was developed to simplify and speed up the task of programming Paradox control panels. Remote
More informationDifferent Ways of Connecting to. 3DLevelScanner II. A.P.M Automation Solutions LTD. www.apm-solutions.com Version 3.0
3DLevelScanner II Different Ways of Connecting to 3DLevelScanner II A.P.M Automation Solutions LTD. www.apm-solutions.com Version 3.0 2 Different Ways of Connecting to 3DLevelScanner II Version 3.0 Table
More informationPM1122 INT DIGITAL INTERFACE REMOTE
PM1122 INT DIGITAL INTERFACE REMOTE PM1122 INT front panel description: 1. Clear wireless remotes knob: push this button for more than 2 seconds to clear the list of all assigned wireless remote settings
More informationUser Manual. Thermo Scientific Orion
User Manual Thermo Scientific Orion Orion Star Com Software Program 68X637901 Revision A April 2013 Contents Chapter 1... 4 Introduction... 4 Star Com Functions... 5 Chapter 2... 6 Software Installation
More informationMaster-Touch and ValuMass. Modbus Communications. INSTRUCTION MANUAL 80202201 (Rev. 2.1)
Master-Touch and ValuMass Modbus Communications INSTRUCTION MANUAL 80202201 (Rev. 2.1) Eldridge Products, Inc. 2700 Garden Road, Building A Monterey, CA 93940 Tel: 800/321-3569 or 831/648-7777 Fax: 831/648-7780
More informationBIT COMMANDER. Serial RS232 / RS485 to Ethernet Converter
BIT COMMANDER Serial RS232 / RS485 to Ethernet Converter (Part US2000A) Copyrights U.S. Converters 1 Contents Overview and Features... 3 Functions..5 TCP Server Mode... 5 Httpd Client Mode.5 TCP Auto mode....6
More informationPartner: Cisco Model: SX80 Device Type: Video Conference
Model: X80 evice Type: Video Conference GENERAL INFORMATION IMPLWINOW NAME: Cisco X80 CATEGORY: Conferencing VERION: 1.2 UMMARY: GENERAL NOTE: CRETRON HARWARE REQUIRE: This module will control the Cisco
More informationSchneider OS-Loader usage via Ethernet or USB.
LHC Gas Systems 28 th February, 2007 Schneider OS-Loader usage via Ethernet or USB. Jacques ROCHEZ - IT/CO/FE Abstract This document is a guideline on how to configure correctly a PC for the use of the
More informationUsing a Laptop Computer with a USB or Serial Port Adapter to Communicate With the Eagle System
Using a Laptop Computer with a USB or Serial Port Adapter to Communicate With the Eagle System ECU DB9 USB 20-060_A.DOC Page 1 of 18 9/15/2009 2009 Precision Airmotive LLC This publication may not be copied
More informationHOMEWORKS. RS-232 Protocol. Data Protocol for Communicating with Lutron's HOMEWORKS System
HOMEWORKS TM HOMEWORKS TM RS-3 Protocol Data Protocol for Communicating with Lutron's HOMEWORKS System HomeWorks RS-3 Protocol Overview HARDWARE OVERVIEW 3 wire RS-3C protocol 9 pin female D type connector
More informationRTI Integration Release Notes
RTI Integration Release Notes Content Introduction...1 Connecting the XP-3 controller to the ClareHome data network...2 Configuring with Integration Designer...2 Configuring in Fusion...6 Button IDs and
More informationCALL MANAGER INSTALLATION
CALL MANAGER INSTALLATION and OPERATION INSTRUCTIONS JULY 17, 2006 Page 1 TABLE OF CONTENTS INTRODUCTION Use of this manual ----------------------------------------------------------------- 2 Product Overview
More informationTI IS-1007 v1.0. TeamConnect. Network and IT configuration
TI IS-1007 v1.0 TeamConnect Network and IT configuration Contents Contents Introduction...3 Configuration and connection possibilities...4 System configuration...5 Network information...7 Core network
More informationHow to setup a serial Bluetooth adapter Master Guide
How to setup a serial Bluetooth adapter Master Guide Nordfield.com Our serial Bluetooth adapters part UCBT232B and UCBT232EXA can be setup and paired using a Bluetooth management software called BlueSoleil
More informationHow To Use A 1232 On A 1236 On A Computer Or A Cell Phone
12-36-1000 Autodialler and Relay Telephone Interface 1.0 INTRODUCTION 12-36-1000 I/O Telephone Interface with AutoDialer The 12-36-1000 is a autodialer and telephone interface that can be used autonomously
More informationINTRODUCTION FEATURES OF THE ICM
INTRODUCTION The ICM, Internet Control Module, is a remote controller device accessible via the Internet that allows operational access to the IPS (and other base units available). Through the ICM you
More informationSUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual
SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual Version 1.0 - January 20, 2015 CHANGE HISTORY Version Date Description of Changes 1.0 January 20, 2015 Initial Publication
More informationDSX Master Communications
DSX Access Systems, Inc. PC to Master Controller - Direct Connect Communications DSX Master Communications Communications between the Comm Server PC and the Master Controller can take several forms which
More informationTechnical Manual. For use with Caller ID signaling types: Belcore 202, British Telecom, & ETSI
Technical Manual For use with Caller ID signaling types: Belcore 202, British Telecom, & ETSI Caller ID.com WHOZZ CALLING? POS 2 Caller ID Monitoring Unit Technical Manual For use with Caller ID signaling
More informationConfiguring IP to Serial with Auto Answer and Serial to IP
Configuring IP to Serial with Auto Answer and Serial to IP You can configure the AirLink device to: Auto answer incoming TCP/IP or UDP/IP connections and send the packet payload out the AirLink device
More informationBASLER ACE QUICK INSTALLATION GUIDE
BASLER ACE QUICK INSTALLATION GUIDE Rev. 01 Quick installation Guide V1 1 Introduction The installation procedures in this guide assume that you want to get your camera operational and begin capturing
More informationIP Interface for the Somfy Digital Network (SDN) & RS485 URTSII
IP Interface for the Somfy Digital Network (SDN) & RS485 URTSII Internet Protocol (IP) Interface Product Options Cat # 1810815 IP Interface Only Cat # 1810870: Interface and DB9/RJ45 Adapter (9015028)
More informationMFC7840W Windows Network Connection Repair Instructions
Difficulty printing from your PC can occur for various reasons. The most common reason a networked Brother machine may stop printing, is because the connection between the computer and the Brother machine
More informationFAQs. XAP Frequently Asked Questions. Software/Configuration
XAP Frequently Asked Questions ~ Software/Configuration ~ Echo Cancellation ~ Audio Performance ~ Expansion Bus ~ Firmware ~ Installation ~ Presets ~ Telephone Hybrid Software/Configuration What is the
More informationModbus and ION Technology
70072-0104-14 TECHNICAL 06/2009 Modbus and ION Technology Modicon Modbus is a communications protocol widely used in process control industries such as manufacturing. PowerLogic ION meters are compatible
More informationSerial Communications
April 2014 7 Serial Communications Objectives - To be familiar with the USART (RS-232) protocol. - To be able to transfer data from PIC-PC, PC-PIC and PIC-PIC. - To test serial communications with virtual
More informationAPPLICATION. Using the PB-100 to Make Calls and Announcements From a Database. Using the PB-100 for All-Call Dialing
APPLICATION Note TELECOM SOLUTIONS FOR THE 21ST CENTURY Using the PB-100 for All-Call Dialing March 22, 2002 Features Compatible with Windows 95, 98, ME, NT 4.0, 2000 Male sub-d 9 pin cable provided 20
More informationGlobal Monitoring + Support
Use HyperTerminal to access your Global Monitoring Units View and edit configuration settings View live data Download recorded data for use in Excel and other applications HyperTerminal is one of many
More informationD8X / D16X IPHONE INTERFACE
Ness icomms App D8X / D16X IPHONE INTERFACE SETUP GUIDE Revision 1.0.0 Table of Contents Copyright Notice... 3 1. Important Information... 4 2. Wiring Diagram... 5 2.1 RS232 Wiring Setup... 5 2.2 IP232
More informationWinPFT File Transfer Utility (Catalog No. 2711-ND7)
Technical Data WinPFT File Transfer Utility (Catalog No. 2711-ND7) Overview WINPFT is a stand-alone Windows utility which lets you transfer applications developed for standard PanelView terminals or Dataliner
More informationDUKANE Intelligent Assembly Solutions
PC Configuration Requirements: Configuration Requirements for ipc Operation The hardware and operating system of the PC must comply with a list of minimum requirements for proper operation with the ipc
More informationenervista UR Setup Software Quick Connect Instructions:
enervista UR Setup Software Quick Connect Instructions: The user can connect to the UR relay via front serial port or rear Ethernet port using the Quick Connect feature of enervista UR Setup software.
More informationSDN INSTRUCTIONS 07/10, Ver 1.2. Somfy Digital Network (SDN) Installation and Programming
Somfy Digital Network (SDN) Installation and Programming SSoomffyy SSyysst teemss IInncc.. 1 Table of Contents 1 General Information and Features... 3 1.1 ILT2 Motor... 3 1.2 SDN Switches... 4 1.3 ILT2
More informationFINS Gateway For OMRON PLCs
1 Purpose This Technical Note describes how to set up a remote collaboration. A remote collaboration consists in configuring, programming or monitoring a PLC from a remote location, without the need of
More informationHow to use KEPServerEX OPC Server (Kepware) with iologik 4000 (Modbus TCP/IP NA-4010 and Modbus Serial NA-4020/NA-4021)
with iologik 4000 (Modbus TCP/IP NA-4010 and Modbus Serial NA-4020/NA-4021) Alex Chen, Senior Engineer, Moxa Technical Support Dept. In this Technical Note, we cover the following topics: 1. How to export
More informationOmron I/O Driver (Series 2) Programmable Serial Interface Card
Omron I/O Driver (Series 2) Programmable Serial Interface Card USER MANUAL Rev. P1.55 June 8, 2012 DeltaV is a trademark of Emerson Process Management, Inc Emerson Process Management, Inc. 1998, 1999.
More informationDeviceMaster UP Modbus Controller to Controller Communication
DeviceMaster UP Modbus Controller to Controller Communication UP Today s Modbus installations are becoming increasingly complex. More and more installations are requiring the use of multiple Modbus controllers
More informationCDI-S100 SERIAL INTERFACE CARD
CDI-S100 SERIAL INTERFACE CARD R R SERIAL INTERFACE MODULE MUSIC MUTE L L GAIN 0 LINE 5 LINE 6 db -10 + 10 MIC LEFT RIGHT FUSE 230V RATING 115V T100mA T200mA POW Installation Guide 2 CDI-S100 Installation
More informationSoftware version 1.1 Document version 1.0
Software version 1.1 Document version 1.0 1 RDNET PROTOCOL OVERVIEW... 2 1.1 Network description... 2 1.2 Connection topology... 2 2 SOFTWARE BASIC OPERATIONS... 3 2.1 Main View elements... 3 2.2 Scanning
More informationUsing IDENT M System T with Modbus/TCP
Using IDENT M System T with Modbus/TCP Introduction The Pepperl+Fuchs IDENT M System T consists of two models MTT3000-F180-B12- V45-MON, which is a read only unit and the MTT6000-F120-B12-V45 which is
More informationApplication Note 2. Using the TCPDIAL & TCPPERM Commands to Connect Two TransPort router Serial Interfaces Over TCP/IP.
Application Note 2 Using the TCPDIAL & TCPPERM Commands to Connect Two TransPort router Serial Interfaces Over TCP/IP. Reverse Telnet or Serial Terminal Server MultiTX feature UK Support March 2014 1 Contents
More informationTechnical Note A007 Modbus Gateway Vantage Pro2 25/09/2009 Rev. A 1 de 7
1 de 7 1. Introduction This Technical Note explains how to configure the Modbus Gateway for Vantage Pro2. The Modbus Gateway allows the easy connection of a PLC (Programmable Logic Controller), RTU (Remote
More informationVoIP Handset User Manual. Digital Voice Quality Business Grade Handset Easy Plug & Play
Digital Voice Quality Business Grade Handset Easy Plug & Play Table of Contents 1.0 Getting Started... 1 1.1 Unpacking the box... 1 1.2 Assembling the Phone... 2 2.0 Phone Button Features... 3 3.0 Phone
More informationGSM Interfacing Board
Campus Component Pvt. Ltd. DISCLAIMER Information furnished is believed to be accurate and reliable at the time of publication. However, Campus Component Pvt. Ltd. assumes no responsibility arising from
More informationSMS Alarm Messenger. Setup Software Guide. SMSPro_Setup. Revision 090210 [Version 2.2]
SMS Alarm Messenger SMSPro_Setup Revision 090210 [Version 2.2] ~ 1 ~ Contents 1. How to setup SMS Alarm Messenger?... 3 2. Install the SMSPro_Setup software... 5 3. Connection Type... 6 4. Connection Port
More informationACTi Streaming Explorer User s Manual Ver 2.1.09
ACTi Streaming Explorer User s Manual Ver 2.1.09 2011/06/24 Overview Streaming Explorer is a Web tool used to manage devices remotely. The Functions provided include Connection, PTZ, DI/DO, Motion, Camera
More informationModBus Server - KNX. Gateway for integration of KNX equipment into Modbus (RTU and TCP) control systems.
IntesisBox ModBus Server - KNX Gateway for integration of KNX equipment into Modbus (RTU and TCP) control systems. Integrate KNX based lighting control into your SCADA, BMS, PLC "talking" Modbus. Master
More informationProfinet to EDV111 Series LED Signs Siemens Function Block Software Manual
Electronic Displays, Inc. EDV111 Series LED Signs Siemens TIA Portal 11, Step 7 Pro Function Block Version Control Version Date Author Change Description 1.0 11/21/2014 d.fox Initial release EDV111 Series
More informationConnecting instruments serially to your computer
Connecting instruments serially to your computer This TechNote will review how to connect instruments (GPS, Sounder, Heading Sensor ) to a computer. Important points such as electrical specification (RS-232
More informationWifi Web Server Module w TF Socket User s Guide
Wifi Web Server Module w TF Socket User s Guide 2004-2010 Sure Electronics Inc. MB-CM14117_Ver1.0 WIFI WEB SERVER MODULE W TF SOCKET USER S GUIDE Table of Contents Chapter 1. Overview...1 1.1 Overview...
More informationTesira Voice-over-IP Interface. Preliminary Steps. Configuring a Cisco CallManager system to work with Biamp s SVC-2 card
Configuring a Cisco CallManager system to work with Biamp s SVC-2 card Tesira Voice-over-IP Interface Biamp s SVC-2 card allows Biamp Tesira digital signal processors to make and receive calls over any
More informationRAM: 2 Gb Hard Drive: 168 hours of recording per Gb of disk space available NIC : 2 NIC cards required for IP Recording.
This guide describes the installation procedures for the BackOffice software when used with the MultiCorder Hardware as a centralized Call Recording and storage solution. The complete MultiCorder BackOffice
More informationI. DigitalCAT Captioning Software Overview... 1. A. Welcome... 1. B. Acquiring the Captioning Add-On... 1. C. Purpose of this Guide...
I. DigitalCAT Captioning Software Overview... 1 A. Welcome... 1 B. Acquiring the Captioning Add-On... 1 C. Purpose of this Guide... 1 II. Direct or Dial-Up Connections... 1 A. Direct Connections... 1 B.
More informationMAGELLAN CONNECTING TO CASH REGISTER EXPRESS
MAGELLAN CONNECTING TO CASH REGISTER EXPRESS Programming codes are for the following products: Magellan 8100 Magellan 8200 Magellan 8300 Magellan 8400 Magellan 8500 Magellan 8500XT Magellan 8500XTS Magellan
More informationWork with Arduino Hardware
1 Work with Arduino Hardware Install Support for Arduino Hardware on page 1-2 Open Block Libraries for Arduino Hardware on page 1-9 Run Model on Arduino Hardware on page 1-12 Tune and Monitor Models Running
More informationDigiLinX Application Note
Using RTI and other Universal Remotes to Control DigiLinX In DigiLinX Dealer Setup 2.3, NetStreams has introduced a new method of controlling DigiLinX from a 3 rd party control system called Serial2Command
More informationControl Protocol Manual
Control Protocol Manual Rev 1.2.0 August 2013 i Table of Contents Control Protocol Manual... i System Control... 3 Software User Interface... 3 Third Party Control... 4 Tesira Text Protocol... 5 TTP Overview...
More informationCENTRONICS interface and Parallel Printer Port LPT
Course on BASCOM 8051 - (37) Theoretic/Practical course on BASCOM 8051 Programming. Author: DAMINO Salvatore. CENTRONICS interface and Parallel Printer Port LPT The Parallel Port, well known as LPT from
More informationAdding or replacing a mesh node in an existing mesh network
Adding or replacing a mesh node in an existing mesh network Use this procedure to add or replace a in an existing mesh For this procedure to work all nodes running the same firmware version. Before you
More informationThe Answer to the 14 Most Frequently Asked Modbus Questions
Modbus Frequently Asked Questions WP-34-REV0-0609-1/7 The Answer to the 14 Most Frequently Asked Modbus Questions Exactly what is Modbus? Modbus is an open serial communications protocol widely used in
More informationAdditional Setup Instructions for Modbus: RTU, ASCII, TCP, Omni & Enron
Additional Setup Instructions for Modbus: RTU, ASCII, TCP, Omni & Enron Copyright 2000 2010 Frontline Test Equipment, Inc. All rights reserved. You may not reproduce, transmit, or store on magnetic media
More informationConfiguring Allen-Brandly ControlLogix PLC with Moxa MGate 5105-MB-EIP. 1 Application Description... 3. 1.1 Objective... 3 1.2 Goals...
Moxa MGate 5105-MB-EIP Contents Moxa Technical Support Team support@moxa.com 1 Application Description... 3 1.1 Objective... 3 1.2 Goals... 3 2 System Topology... 3 3 Hardware and Software Requirements...
More informationIntesisBox ASCII Server - LON
IntesisBox ASCII Server - LON Gateway for integration of LON devices into ASCII enabled control systems. Integrate Air Conditioning from the main manufacturers (DAIKIN, Mitsubishi Electric, Mitsubishi
More informationL1255-4149 Firmware And FPGA Configuration Upgrade
Technical Note TN133 Issue:2 L1255-4149 Firmware And FPGA Configuration Upgrade IMPORTANT NOTE: When using USB to Serial converters and upgrading the Firmware there is a danger of early L1255s becoming
More informationIP Indoor High Speed Dome. CAM-6500 series. Ver. 070307. Quick Installation Guide
IP Indoor High Speed Dome CAM-6500 series Ver. 070307 Quick Installation Guide 1 1 Getting Started 1.1 PACKAGE CONTENTS CAM-6500 series Warranty Card Software CD Power & A/V Cable LAN/WAN Cable Alarm Cable
More informationBack Office Recorder 4iP Installation Guide Intelligent Recording Limited
Back Office Recorder 4iP Installation Guide Intelligent Recording Limited Downloads Available at www.usbcallrecord.com UK Office +44 (0) 1909 512148 US Office +1 949.587.1226 Copyright Intelligent Recording
More informationSEC 4100 SYSTEM MONITOR Programmable Serial Interface Card Series 2
SEC 4100 SYSTEM MONITOR Programmable Serial Interface Card Series 2 USER MANUAL Rev. P1.11 September 13, 2006 DeltaV is a trademark of Emerson Process Management, Inc Emerson Process Management, Inc. 1998,
More informationHitachi HCX Integration
Rev date: 04/08/04 Innovation Voice Mail Hitachi HCX Integration 1841 Bourbon Road Cross Plains, Wisconsin 1-800-424-6757 www.innovationtw.com Hitachi HCX Integration REQUIREMENTS: HCX-5000 with software
More informationToshiba Serial Driver Help. 2012 Kepware Technologies
2012 Kepware Technologies 2 Table of Contents Table of Contents 2 3 Overview 3 Device Setup 4 Modem Setup 4 Cable Diagram - EX100/200 PLCs 4 Cable Diagram - T1 PLCs 5 Cable Diagram - T2/T3 PLCs 5 Cable
More informationLAN / WAN Connection Of Instruments with Serial Interface By Using a Terminal Server
Products: EFA with EFA Scan, DVRM and DVMD with Realtime Monitor or Stream Explorer DVMD-B1 LAN / WAN Connection Of Instruments with Serial Interface By Using a Terminal Server Remote control of test and
More informationMS830 / MS833 Barcode Reader v1.0 9-December-2014
MS830 / MS833 Barcode Reader v1.0 9-December-2014 Publication Information 2014 Imagine Communications Corp. Proprietary and Confidential. Imagine Communications considers this document and its contents
More informationMANUAL PC1000R INFO@APART-AUDIO.COM
MANUAL PC1000R INFO@APART-AUDIO.COM Features The APart PC1000R is a professional multisource CD/USB/SD card music player, equipped with balanced and unbalanced analog outputs, coaxial and optical digital
More informationPC Program User s Guide (01.01.05) 1. Connecting the PC. 2. Installation and Start-up. 3. Programming
Work Off-Line Set up a new database or modify a previously saved database (without being connected to the telephone system). This helps minimize on-site programming time. Work On-Line (connected directly
More informationPAP2 Phone Adapter. Installation Guide OUTBOUND CALLING. Version 1.0. DocVersion: PAP2-IG-v1-0-042805
PAP2 Phone Adapter Installation Guide OUTBOUND CALLING Version 1.0 DocVersion: PAP2-IG-v1-0-042805 All Rights Reserved Copyright 2005 The use, disclosure, modification, transfer, or transmittal of this
More informationAPPLICATION NOTE # Using Sage SMOS for VoIP Testing, IP Phone to IP Phone TABLE OF CONTENTS
Product: 930A L3 Communications Test Set 935AT Communications Test Set APPLICATION NOTE # Using Sage SMOS for VoIP Testing, IP Phone to IP Phone TABLE OF CONTENTS Introduction... 2 Configuring 935AT #1
More informationBasic Features. In the Phone application. Making a call. Answer or divert calls
Basic Features. Using the Phone applica5on Making a call In the Phone application, enter a number, and press the key to make a call. To change the number, use you have entered. to delete the digits After
More informationCrow Limited Warranty. Print Version 017
Crow Limited Warranty (Crow) warrants this product to be free from defects in materials and workmanship under normal use and service for a period of one year from the last day of the week and year whose
More information