Schneider OS-Loader usage via Ethernet or USB.

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Schneider OS-Loader usage via Ethernet or USB."

Transcription

1 LHC Gas Systems 28 th February, 2007 Schneider OS-Loader usage via Ethernet or USB. Jacques ROCHEZ - IT/CO/FE Abstract This document is a guideline on how to configure correctly a PC for the use of the Schneider OS-loader.

2 1 Products 1.1 Software tool: Schneider OS-Loader This tool is now included inside the UNITY environment. But you may download a version from CERN-Schneider-Support In the case of the update of Premium PLC, we need to use two methods of downloading, one with the UNITELWAY protocol on serial line, and one with a protocol xx on top of TCP/IP. One important point is that By default the OS-loader (V2.1) is running via the COM port 1 of the PC. 1.2 Hardware component: A specific connector must be used between the PC and the PLC unit The TSXPCU1031 with a DB9 connector The TSXPCU3031 with an USB connector. 2 Downloading with the UNITELWAY protocol. This is the case for the update of a PLC firmware 2.1 Connection via a COM port1 on DB9 connector. You just have to set the port rate at 9600 bauds, 8 data bits, No parity, 1 stop bit, no FlowControl. On premium, the terminal port seems to be in auto mode. The default configuration is: bits/s, 8 data bits, 1 stop bit, Odd parity. So the speed of bits/s should be fine (not yet tested) 2.2 Connection via an USB interface. This is rather more difficult, A software driver must be loaded and configured to emulate the COM port1 via the USB network. When you connect for the first time the TSXPCU3031, the OS will request for the installation of a Driver. 1

3 Windows XP has a default driver. Schneider does also provide a driver. CERN-Schneider-Support Case of the Portable NEC VERSA. NEC recommends installing its own driver To correctly configure the Universal Serial Bus (USB) Controller, download and install the Versa S260 USB 2.0 Driver Procedure: Download the self extracting file and double click on the file. It will create a folder C:\PNP\USB2 1. Click My Computer with the secondary mouse button 2. Select Properties from the pop-up menu that appears 3. Click the Hardware tab 4. Click the Device Manager button 5. Double-click USB Controllers 6. Double-click the driver already listed (e.g. PCI Display Adapter) 7. In the Device Properties window, select the Driver tab 8. Click the Update Driver button so that the Upgrade Device Driver Wizard will appear 9. Click the Next button 10. Select Search for a suitable driver for my device (recommended) and click Next 11. Select Specify a location and click Browse Browse to the folder where the drivers are located C:\PNP\USB Click OK, click Next, and follow the on screen instructions 14. Close device properties window by clicking Close 15. Restart your computer (when prompted) 2

4 2.2.2Assignment of the USB driver to the port COM1. Usually, there is already a driver assigned to the port COM1, therefore the silent installation will provide another COM number to this driver. As already mentioned, the Os-Loader works only with COM1 and some action have to be performed. 1. Click My Computer with the secondary mouse button 2. Select Properties from the pop-up menu that appears 3. Click the Hardware tab 4. Click the Device Manager button 5. Double-click Ports (COM &LPT) 6. If the COM1 is already present, 1. Right Click on this port and select Properties 2. Click the Port Setting tab 3. click advance 4. In the windows, move the selected port COM1 to an unused one 5. Find the COM port with the description on USB Serial Converter Multi-Function Cable, 6. Once you have it, assign the value COM1. 7. reboot the PC, That all, 8. OS loader should works via the USB cable. 7. If the COM1 is not present, proceed as from step 6.5 for that you may use the step It may occur that a message This COM name is being used then you have to find what type of hardware it refer to, 9. Connect this hardware to the PC and then the COM1 will appear in the list. 10. Now you may proceed from step 6 3

5 3 Downloading via the TCP protocol. This is the case for the update of an Ethernet co processor. The download of the Ethernet can only be performed via the Ethernet port. The PC and the PLC have to be connected to the same network, either via a Hub/switch or directly with a crossed UTP cable. 3.1 PC configured with an Automatic IP address assignment. When you are on an isolated network, the PC will not get an IP number. You have to set one Dummy IP to allow the communication This may be achieved via 11. Click select on the Windows Start key (left bottom), the Setting key. 12. Select Network Connections 13. Select Local Area Connection 14. On the General Tab Click the Properties button 15. deselect the Obtain IP address automatically 16. Now you configure the IP address, Subnet mask and default gateway (a random value) 17. You don t need to reboot the PC. 18. Perform the downloading task with the OS-Loader 19.!!! Once it s over, don t forget to place back the Automatic IP assignment. End 4

Application Note: Connecting to a 2500 Series Processor using PLC Workshop

Application Note: Connecting to a 2500 Series Processor using PLC Workshop Application Note: Connecting to a 2500 Series Processor using PLC Workshop This application note will describe a step by step process for the three ways to connect to a 2500-CXXX with PLC Workshop. The

More information

Configuring Windows 7 64 bit for AutoVISION

Configuring Windows 7 64 bit for AutoVISION This document will describe how to configure a 64 bit version of Windows 7 Professional, Ultimate or Enterprise to utilize the Windows XP Mode (Virtual PC) capabilities to allow AutoVISION to be used in

More information

USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6

USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly

More information

Select Correct USB Driver

Select Correct USB Driver Select Correct USB Driver Windows often installs updated drivers automatically, and defaults to this latest version. Not all of these drivers are compatible with our software. If you are experiencing communications

More information

2 Preparation. 2.1 Items to Check Connecting PC with GP Setting PC Network Setting GP Network...

2 Preparation. 2.1 Items to Check Connecting PC with GP Setting PC Network Setting GP Network... 2 Preparation 2.1 Items to Check...2-2 2.2 Connecting PC with GP...2-6 2.3 Setting PC Network...2-9 2.4 Setting GP Network...2-27 2-1 Items to Check 2.1 Items to Check Before installing this product, ensure

More information

SOP085 - HELLER OVEN SOFTWARE INSTALLATION PROCEDURE. For version 6.2.x.x

SOP085 - HELLER OVEN SOFTWARE INSTALLATION PROCEDURE. For version 6.2.x.x SOP085 - HELLER OVEN SOFTWARE INSTALLATION PROCEDURE For version 6.2.x.x DATE REV ECN - DESCRIPTION OF CHANGE Initials 02/20/2014 INT ECN 140003-001 TP For version 6.2.x.x Rev. INT Page 1 of 16 Basic PC

More information

IP SERIAL DEVICE SERVER

IP SERIAL DEVICE SERVER IP SERIAL DEVICE SERVER ( 1 / 2 / 4 serial port ) Installation guide And User manual Version 1.0 1Introduction... 5 1.1Direct IP mode...5 1.2Virtual COM mode...5 1.3Paired mode...6 1.4Heart beat... 6

More information

ETHERNET WEATHER STATION CONNECTIONS Application Note 33

ETHERNET WEATHER STATION CONNECTIONS Application Note 33 ETHERNET WEATHER STATION CONNECTIONS Application Note 33 With WeatherLink and a Device Server INTRODUCTION It is possible to substitute an Ethernet connection for the direct USB or serial connection that

More information

Guide to Installing BBL Crystal MIND on Windows 7

Guide to Installing BBL Crystal MIND on Windows 7 Guide to Installing BBL Crystal MIND on Windows 7 Introduction The BBL Crystal MIND software can not be directly installed on the Microsoft Windows 7 platform, however it can be installed and run via XP

More information

Oven Software Installation for Windows XP (HC1 or HC2 controller) (Software version 4.0.x.x)

Oven Software Installation for Windows XP (HC1 or HC2 controller) (Software version 4.0.x.x) Basic System requirement: OS: Windows XP (Home or Professional) Processor speed: preferred 2GHz or more RAM: 256MB minimum Communication using: For HC1-x controller: Serial Com port-1 (built-in to computer

More information

Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2

Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2 Ethernet Interface Manual Thermal / Label Printer Rev. 1.01 Metapace T-1 Metapace T-2 Metapace L-1 Metapace L-2 Table of contents 1. Interface setting Guiding...3 2. Manual Information...4 3. Interface

More information

Installing PowerLink on Windows 7 64-bit

Installing PowerLink on Windows 7 64-bit Instruction Manual Version 1.0, Code No. 20 751 806 1 Introduction... 3 2 Installing Virtual PC... 3 3 Configuring Windows XP Mode... 5 4 Installing Powerlink to Virtual XP... 8 5 Run PowerLink software

More information

DUKANE Intelligent Assembly Solutions

DUKANE Intelligent Assembly Solutions PC Configuration Requirements: Configuration Requirements for ipc Operation The hardware and operating system of the PC must comply with a list of minimum requirements for proper operation with the ipc

More information

64-Bit Compatibility with Micromeritics Applications

64-Bit Compatibility with Micromeritics Applications Tech Tip 7 64-Bit Compatibility with Micromeritics Applications Micromeritics products are designed to operate in most Microsoft Windows environments. However, more current versions of Microsoft Windows,

More information

Contents 1. MAKING CONNECTION VIA USB 2 2. MAKING CONNECTION VIA RS SETTING UP INTERN ET CONNECTION FOR WINDOWS OS 27

Contents 1. MAKING CONNECTION VIA USB 2 2. MAKING CONNECTION VIA RS SETTING UP INTERN ET CONNECTION FOR WINDOWS OS 27 Omni 56K Plus Modem Read Me First Contents 1. MAKING CONNECTION VIA USB 2 HARDWARE INSTALLATION...2 SOFTWARE INSTALLATION FOR WINDOWS OS...4 UNINSTALLATION...7 INSTALL USB DRIVER AND SETUP PPP FOR MACOS...9

More information

8-Port 10/100Mbps + 2- Gigabit TP/SFP. Managed Switch FGSD-1022 / FGSD-1022P. Quick Installation Guide

8-Port 10/100Mbps + 2- Gigabit TP/SFP. Managed Switch FGSD-1022 / FGSD-1022P. Quick Installation Guide 8-Port 10/100Mbps + 2- Gigabit TP/SFP Managed Switch FGSD-1022 / FGSD-1022P Quick Installation Guide Table of Contents 1. Package Content... 3 2. Requirements... 4 3. Terminal Setup... 5 4. Logon to the

More information

Installing AxtraxNG Creating Networks and Finding Panels

Installing AxtraxNG Creating Networks and Finding Panels Installing AxtraxNG Creating Networks and Finding Panels Technical Support Engineering Rosslare Security NA For more information please see www.axtraxng.com This document will guide you through creating

More information

Quick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012

Quick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012 Quick Note 32 Using Digi RealPort with a Digi TransPort Router UK Support September 2012 1 Contents 1 Introduction... 3 1.1 Outline... 3 1.2 Assumptions... 3 1.3 Version... 3 2 Configuration & scenario...

More information

VBOX-Plus Configuration Tool

VBOX-Plus Configuration Tool Version 1.0 October 2012 VBOX-Plus Configuration Tool Table of Contents System Requirements Program Installation Connecting to the VBOX-Plus Gateway System Configuration Resetting to Factory Default Registering

More information

Midland BT Updater BTUpdater Program Program file (x86) ), Midland

Midland BT Updater BTUpdater Program Program file (x86) ), Midland Midland BT Updater After you downloaded the BT Updater setup application from the web site, double click on it and follow the installation procedure. The BTUpdater application is automatically installed

More information

To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:

To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification: PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,

More information

1 INTRODUCTION. This document describes the procedure to upgrade LTMR.

1 INTRODUCTION. This document describes the procedure to upgrade LTMR. 1 INTRODUCTION This document describes the procedure to upgrade LTMR. Limitation: this package and procedure describe only the upgrade of the LTMR firmware for all network versions (Modbus, Profibus, DeviceNet,

More information

evcom Standard serial communications

evcom Standard serial communications ewon Application User Guide AUG 032 / Rev 1.0 You Select, We Connect evcom Standard serial communications Content evcom is the Virtual COM software for ewon. With ewon and evcom software, you can achieve

More information

Centurion PLUS CPC4 Download Guide

Centurion PLUS CPC4 Download Guide Centurion PLUS CPC4 Download Guide using C4 File Transfer Utility. 1010537 03 01 10 Section 50 1.0 Background: 1.1 The Centurion PLUS Control system consists of a Centurion PLUS Core (CPC4 1) and Color

More information

XConsole GUI setup communication manual September 2010.

XConsole GUI setup communication manual September 2010. XConsole GUI setup communication manual September 2010. XConsole is compatible with Microsoft XP, Vista and Windows 7. The software will also work if using Boot camp on a Mac. IMPORTANT NOTES: - Do NOT

More information

Revision Update Instructions- Using Legacy Connect PREP:

Revision Update Instructions- Using Legacy Connect PREP: Revision Update Instructions- Using Legacy Connect Some older versions of Predator software cannot be auto detected by the DS Downloader. Any tool with a revision starting with 7rxx and some older 8rxx

More information

GE-DS-242-PoE Managed Ethernet Switch Installation Sheet

GE-DS-242-PoE Managed Ethernet Switch Installation Sheet GE Security GE-DS-242-PoE Managed Ethernet Switch Installation Sheet Package Contents Thank you for purchasing the GE Security GE-DS-242-PoE a 24-Port Fast Ethernet + 2-Port Gigabit TP/SFP Combo Managed

More information

Phaser 3635MFP Software Upgrade Process

Phaser 3635MFP Software Upgrade Process Overview Phaser 3635MFP Software Upgrade Process The Software Upgrade feature allows the customer to upgrade the machine software as requested by a Xerox Customer Support Center Representative, without

More information

User's Manual Ethernet Interface. SRP-275 SRP-280 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400.

User's Manual Ethernet Interface. SRP-275 SRP-280 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400. User's Manual Ethernet Interface Rev. 5.00 SRP-270 SRP-275 SRP-280 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400 http://www.bixolon.com Table of contents 1. Interface setting Guiding...3 2.

More information

Figure 1: Starting the search for driver for USB HID device

Figure 1: Starting the search for driver for USB HID device Windows 98 Installation Procedure for the USB Drivers (Virtual Com) For Windows Me: Follow steps 1-8 on pages 7-12 For Windows 2000: Follow steps 1-11 on pages 13-18 For Windows XP: Follow steps 1-12 on

More information

BASLER ACE QUICK INSTALLATION GUIDE

BASLER ACE QUICK INSTALLATION GUIDE BASLER ACE QUICK INSTALLATION GUIDE Rev. 01 Quick installation Guide V1 1 Introduction The installation procedures in this guide assume that you want to get your camera operational and begin capturing

More information

SATO Network Interface Card Configuration Instructions

SATO Network Interface Card Configuration Instructions SATO Network Interface Card Configuration Instructions Table of Contents 1. Reset of wired/wireless interface card... 3 2. Installing the All-In-One Utility (recommended)... 4 3. Configuring wired/wireless

More information

Colorfly Tablet Upgrade Guide

Colorfly Tablet Upgrade Guide Colorfly Tablet Upgrade Guide (PhoenixSuit) 1. Downloading the Firmware and Upgrade Tool 1. Visit the official website http://www.colorful.cn/, choose 产 品 > 数 码 类 > 平 板 电 脑, and click the product to be

More information

CMP-102U. Quick Installation Guide

CMP-102U. Quick Installation Guide CMP-102U Quick Installation Guide V1.0 http://www.cnet.com.tw 1 CMP-102U Supports One High-speed USB2.0 Port MFP Server Supports 10/100Mbps Fast Ethernet Network Quick Installation Guide 1 Package Contents:

More information

User Manual Network Interface

User Manual Network Interface User Manual Network Interface Rev. 1.00 SRP-350plusll SRP-352plusll http://www.bixolon.com Table of Contents 1. Manual Information...3 2. Specifications...3 2-1 Hardware version...3 2-2 Configuration Tool...3

More information

Firmware Update Guide Rev. C

Firmware Update Guide Rev. C Firmware Update Guide 92-2616-01 Rev. C Contents 1 Upgrade Utility and Printer Firmware Requirements 1 1. pw Thermal Printer Upgrade Utility 1 2. Printer Firmware 1 3. Initial Preparation 1 2 Upgrading

More information

Installing CDM Drivers

Installing CDM Drivers Installing CDM Drivers To install CDM drivers for an FTDI device under Windows 2000, follow the instructions below: If a device of the same type has been installed on your machine before and the drivers

More information

Additional Requirements for ARES-G2 / RSA-G2. One Ethernet 10 Base T/100 Base TX network card required for communication with the instrument.

Additional Requirements for ARES-G2 / RSA-G2. One Ethernet 10 Base T/100 Base TX network card required for communication with the instrument. TA Instruments TRIOS Software Installation Instructions Installation Requirements Your TRIOS Instrument Control software includes all the components necessary to install or update the TRIOS software, as

More information

PP8X Printer Driver Installation Instruction

PP8X Printer Driver Installation Instruction PP8X Printer Driver Installation Instruction Pinnacle Technology Corp. CONTENTS 1 BT Device Installation... 1 2 Printer Driver Installation... 6 3 How to Know the Connecting Port... 10 4 How to Configure

More information

Windows 8 Installation Instructions for the PR3. STOP! Read these instructions before connecting the PR-3 to your Computer

Windows 8 Installation Instructions for the PR3. STOP! Read these instructions before connecting the PR-3 to your Computer Windows 8 Installation Instructions for the PR3 Required equipment: PR3 Installation CD or downloaded and extracted PR3 files from www.digitrax.com/downloads (PR3 Windows XP and Vista Drivers) USB Cable

More information

Windows XP.. ELITE Firmware Update procedures.. v1.41

Windows XP.. ELITE Firmware Update procedures.. v1.41 Windows XP.. ELITE Firmware Update procedures.. v1.41 Download and Extract the ELITE update. Note.. Please ensure you are logged in to Windows as an Administrator before carrying out the instructions in

More information

Keri USB-A Connection and Configuration

Keri USB-A Connection and Configuration Step 1 - Connect the KPC-1 cable to the K-USB. NOTE: The form of the USB converter may vary, so the unit you receive may not be identical to the one displayed here. Step 2 Plug the USB Connector of the

More information

USB to RS-485 Optically Isolated Interface Handbook Revision 1.0

USB to RS-485 Optically Isolated Interface Handbook Revision 1.0 311-70 USB to RS-485 Optically Isolated Interface Handbook Revision 1.0 Contents Overview... 1 RS-485 Connections... 1 Shield... 1 Line Term... 2 Bias 1 & Bias 2... 2 RS-485 Cable... 2 USB Installation...

More information

Connecting your Omega/BetaPAT PLUS to a PC via a USB

Connecting your Omega/BetaPAT PLUS to a PC via a USB Connecting your Omega/BetaPAT PLUS to a PC via a USB Install software Windows XP and below Insert the disc into your computers disc drive and run through the setup wizard. Windows Vista & 7 1. Insert the

More information

Pass-through Function

Pass-through Function Chapter 29 Pass-through Function... 2 29.1 Ethernet Mode... 3 29.1.1 How to install virtual serial port driver... 3 29.1.2 How to Change the Virtual Serial Port... 4 29.1.3 How to Use Ethernet Mode...

More information

ScanWin Installation and Windows 7-64 bit operating system

ScanWin Installation and Windows 7-64 bit operating system ScanWin Installation and Windows 7-64 bit operating system In order to run the ScanWin Pro install and program on Windows 7 64 bit operating system you need to install a Virtual PC and then install a valid,

More information

FINS Gateway For OMRON PLCs

FINS Gateway For OMRON PLCs 1 Purpose This Technical Note describes how to set up a remote collaboration. A remote collaboration consists in configuring, programming or monitoring a PLC from a remote location, without the need of

More information

How to Set Up Network Communication for PTW Detector Arrays without DHCP

How to Set Up Network Communication for PTW Detector Arrays without DHCP Technical Note D252.200.02/02 How to Set Up Network Communication for PTW Detector Arrays without DHCP VeriSoft 5.1 or higher Detector Interface 4000 (T16039) This technical note applies to the following

More information

Wireless Network Setup Guide NPD EN

Wireless Network Setup Guide NPD EN Wireless Network Setup Guide NPD4759-00 EN Checking Your Network Confirm your computer s network settings, and then choose what to do next. Follow the instructions for the environment in which your network

More information

Dec MOISTURE ANALYZER MOC63u. Device Driver Installation Manual (English Version)

Dec MOISTURE ANALYZER MOC63u. Device Driver Installation Manual (English Version) 321-78025 Dec.2010 MOISTURE ANALYZER MOC63u Device Driver Installation Manual (English Version) i Table of Contents 1 Introduction... 1 2 Installation on Windows XP... 2 2.1. USB Serial Converter... 2

More information

File Management Utility. T u t o r i a l

File Management Utility. T u t o r i a l File Management Utility T u t o r i a l Contents System Requirements... 2 Preparing Files for Transfer to GlobalMark... 2 Application Launch... 2 Printer Setup... 2 Communication Status... 4 Communication

More information

Visual Quick Start Guide Printer Driver Install on Windows XP

Visual Quick Start Guide Printer Driver Install on Windows XP Visual Quick Start Guide Printer Driver Install on Windows XP Printer Driver Download Download Printer Driver from Transact Web Site www.transact-tech.com 1. First make sure your printer is powered on

More information

WORKSTATION CONFIGURATION FOR NEW GALILEO MANAGED VPN SITES

WORKSTATION CONFIGURATION FOR NEW GALILEO MANAGED VPN SITES WORKSTATION CONFIGURATION FOR NEW GALILEO MANAGED VPN SITES WINDOWS 98 GENERAL NETWORK CONFIGURATION Ask the customer which workstation the primary Scriptwriter person in the office will use. That person

More information

Network Settings. User Guide. Date: November 7 th, 2014 Revision Real Time Automation, Inc

Network Settings. User Guide. Date: November 7 th, 2014 Revision Real Time Automation, Inc Network Settings User Guide Date: November 7 th, 2014 Revision 1.04 Real Time Automation, Inc. 1 1-800-249-1612 Overview The Network Settings User Guide will walk through setting up the gateway on the

More information

USB Driver Installation for Windows XP

USB Driver Installation for Windows XP USB Driver Installation for Windows XP USB Serial Converter Driver Installation for Windows XP CAUTION: You must use the drivers on the CD-ROM supplied with your USB Device. DO NOT download drivers from

More information

Configuring the Switch with the CLI Setup Program

Configuring the Switch with the CLI Setup Program APPENDIXC Configuring the Switch with the CLI Setup Program This appendix provides a command-line interface (CLI) setup procedure for a standalone switch. To set up the switch by using Express Setup, see

More information

Elite and elink Driver Installation

Elite and elink Driver Installation Elite and elink Driver Installation For Hornby DCC Controllers (Revision May 2013) Copyright 2013 by Invicto Systems Limited. All rights reserved. Preface With the increasing number of different versions

More information

DaVinci Firmware Update Instructions

DaVinci Firmware Update Instructions Note: You must use a Windows based PC for the manual update process. Step 1: Confirm Your DaVinci is Compatible and choose your update method With the DaVinci in Reading Mode, Press and Hold the FIND and

More information

Chase Mode Manager Software

Chase Mode Manager Software Please read and understand this instruction manual thoroughly before using this product. for Mini-Z series equipped with an Rx unit with Chase Mode Chase Mode Manager Software Instruction Manual This instruction

More information

Pulsar 320 TCP/IP Setup Instructions

Pulsar 320 TCP/IP Setup Instructions Pulsar 320 TCP/IP Setup Instructions Contents: 1.0 Configure network settings for the PC - Connect through a network or router - Direct connect with a single PC connection 2.0 Connection to the Pulsar

More information

Hypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide

Hypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide Hypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide Hypercom Corporation 8888 East Raintree Drive Scottsdale, Arizona 85260 USA Corporate Telephone: 480.642.5000 Corporate

More information

Installing the IF-NMEASC & SC30 Windows XP Drivers & Software

Installing the IF-NMEASC & SC30 Windows XP Drivers & Software Installing the IF-NMEASC & SC30 Windows XP Drivers & Software The following document will outline the installation and use of the IF-NMEASC and SC-30 USB drivers and SC-30Tool software in three parts:

More information

Operating Instructions

Operating Instructions Operating Instructions (For Setting up the Printer Driver and the Panasonic Document Management System) Digital Imaging Systems Model No. DP-800P / 800E / 806P Installation Table of Contents Installation

More information

SATO Network Interface Card Configuration Instructions

SATO Network Interface Card Configuration Instructions SATO Network Interface Card Configuration Instructions Table of Contents Section Page 1. Reset of wired/wireless interface card 3 2. Installing the All-In-One Utility 4 3. Installing the Admin Manager

More information

User Manual. Thermo Scientific Orion

User Manual. Thermo Scientific Orion User Manual Thermo Scientific Orion Orion Star Com Software Program 68X637901 Revision A April 2013 Contents Chapter 1... 4 Introduction... 4 Star Com Functions... 5 Chapter 2... 6 Software Installation

More information

DSL-302G ADSL Modem Quick Installation Guide

DSL-302G ADSL Modem Quick Installation Guide DSL-302G ADSL Modem Quick Installation Guide INDEX 1. Installing the modem 1.1. Software installation 1.2. Connecting modem to PC 2. Configuring the modem 3. Troubleshooting 3.1. Troubleshooting driver

More information

SAPIP GUI INSTALLATION. Table of Contents

SAPIP GUI INSTALLATION. Table of Contents QUICK START GUIDE SAPIP GUI INSTALLATION Table of Contents 1. Install CSU cable driver for SapIP..2-3 2. Check for pre-requisite for SAPIP GUI install......2 3. Check for pre-requisite for SAPIP GUI install...2-6

More information

Using a simple crossover RJ45 cable, you can directly connect your Dexter to any computer.

Using a simple crossover RJ45 cable, you can directly connect your Dexter to any computer. Dexter is a network device using the Ethernet protocol to connect and communicate with other devices on the network: Computers, routers, DHCP servers. Thus you have to setup your Dexter and your network

More information

Configuring the Beckhoff BK9000 Network Parameters

Configuring the Beckhoff BK9000 Network Parameters Configuring the Beckhoff BK9000 Network Parameters Section Title Page 1 Overview of Steps 1 2 Parts List 1 3 Required Software 1 4 Install Required Software 2 5 Configure Network Parameters 3 1 Overview

More information

Network Configuration Guide

Network Configuration Guide COMPLIANT MANAGER Model name: BMS-CM1280FTLE Prohibited Never connect the Compliant Manager to the Internet. We assume no responsibility for any problems resulting from connection to the Internet. Only

More information

AcqKnowledge 3.7.3 or better for Windows OS (version compatibility varies each release)

AcqKnowledge 3.7.3 or better for Windows OS (version compatibility varies each release) APPLICATION NOTES 42 Aero Camino, Goleta, CA 93117 Tel (805) 685-0066 Fax (805) 685-0067 info@biopac.com www.biopac.com 09.10.2007 Application Note 209: AcqKnowledge for Windows: Upgrade for 1+MP150s and

More information

DSL Installation Guide

DSL Installation Guide DSL Installation Guide Thank you for choosing Integra Telecom s DSL service! Introduction This guide will walk you through the DSL installation process and will help you configure a computer to access

More information

Preparing the Windows version of the software for use

Preparing the Windows version of the software for use Preparing the Windows version of the software for use System requirements Component Processor RAM Hard disk Drives Interfaces/network TCP/IP internet protocol Screen Installing the Conference Manager software

More information

Installation Instructions for 9555 USB Driver

Installation Instructions for 9555 USB Driver Prior to using the data modem features of your 9555 handset; you must first install the VCOMPORT 9555 USB Driver. This driver is compatible with: Windows XP Service Pack 2, Windows 2000 Service Pack 4,

More information

Appendix C Preparing Your Network

Appendix C Preparing Your Network Appendix C Preparing Your Network This appendix describes how to prepare your network to connect to the Internet through the FVX538 ProSafe VPN Firewall 200 and how to verify the readiness of broadband

More information

Installing a Westell USB Network Adapter

Installing a Westell USB Network Adapter Installing a Westell USB Network Adapter Before You Begin Before you begin installing your Westell USB Network adapter: 1. Make sure the computer with the USB adapter meets the minimum system requirements

More information

1-Port Wireless USB 2.0 Print Server Model # APSUSB201W. Quick Installation Guide. Ver. 2A

1-Port Wireless USB 2.0 Print Server Model # APSUSB201W. Quick Installation Guide. Ver. 2A 1-Port Wireless USB 2.0 Print Server Model # APSUSB201W Quick Installation Guide Ver. 2A Section 1 Step 1Connect one end of the Ethernet cable to the RJ-45 port of the Print Server and attach the other

More information

NAS 107 Introduction to Control Center

NAS 107 Introduction to Control Center NAS 107 Introduction to Control Center Perform basic management on your NAS using Control Center A S U S T O R C O L L E G E COURSE OBJECTIVES Upon completion of this course you should be able to: 1. Use

More information

TL-PS310U Single USB 2.0 Port MFP and Storage Server

TL-PS310U Single USB 2.0 Port MFP and Storage Server TL-PS310U Single USB 2.0 Port MFP and Storage Server Rev: 2.0.0 1910010313 Contents Chapter 1 Introduction... 1 1.1 Product Overview...1 1.2 Network Management...1 1.3 Components and Features...1 1.4 Hardware

More information

Omni 56K USB Lite Quick Start Guide

Omni 56K USB Lite Quick Start Guide Omni 56K USB Lite Quick Start Guide ZyXEL TOTAL INTERNET ACCESS SOLUTION 1. Hardware Installation Connect your modem to your analog phone or fax. Use the phone cord included to connect to the phone jack

More information

How to Configure QUICKCHECK webline for Network Communication without DHCP

How to Configure QUICKCHECK webline for Network Communication without DHCP Technical Note D871.200.04/00 How to Configure QUICKCHECK webline for Network Communication without DHCP Firmware 1.5 or higher WorklistGenerator version 1.5 NOTE This technical note explains how to configure

More information

Prestige 650 Read Me First

Prestige 650 Read Me First Prestige 650 Read Me First Prestige Rear Panel Connections PORT DSL CONSOLE LAN 10/100M POWER Connect to a telephone jack using a telephone wire. CONNECTION Connect to a serial port (COM port) on your

More information

Digi XBee Application Note Configuring a Digi XBee Wifi module for TCP Socket

Digi XBee Application Note Configuring a Digi XBee Wifi module for TCP Socket 1. Configure a Digi XBee Wifi module as a TCP Client to connect to a TCP Server for sending/receiving data in an Ad Hoc network. Objective: Configure a TCP Socket connection between a Digi XBee Wifi module

More information

How to install USB driver (MICRO/I)

How to install USB driver (MICRO/I) How to install USB driver (MICRO/I) Install on Windows XP 1. Connect the USB port on HG3G series and the USB port on PC. 2. Windows displays Found new Hardware Wizard. Select No, not this time and press

More information

Printer Support Guide. FedEx Ship Manager Software

Printer Support Guide. FedEx Ship Manager Software Printer Support Guide FedEx Ship Manager Software Printer FAQs Installing Printer Drivers How do I download and install the Zebra printer drivers? To download and install the current Zebra printer drivers

More information

Universal Serial Bus

Universal Serial Bus Universal Serial Bus Application Note Copyright 2008 Sierra Wireless. All rights reserved. Rev 1.0 Universal Serial Bus (USB) Changing the USB port communication Installing the USB driver Using the Virtual

More information

How to Download Images Using Olympus Auto-Connect USB Cameras and Olympus Master

How to Download Images Using Olympus Auto-Connect USB Cameras and Olympus Master How to Download Images Using Olympus Auto-Connect USB Cameras and Olympus Master Introduction Auto-Connect USB is a feature that allows Olympus digital cameras to emulate a Hard disk drive when connected

More information

Gateway for MPI Siemens PLC

Gateway for MPI Siemens PLC 1 Purpose This document describes how to set up a remote collaboration with a using an ewon as gateway. The remote collaboration will be set up for two network topologies: Figure 1: Network topologies

More information

CODESOFT Installation Scenarios

CODESOFT Installation Scenarios CODESOFT Installation Scenarios NOTES: CODESOFT is a separate install from existing versions of CODESOFT. You will need to make note of your current settings (default directories, etc.) so you can duplicate

More information

Wireless PC Port. Installation Guide

Wireless PC Port. Installation Guide Wireless PC Port Installation Guide 2Wire PC Port USB to HPNA Adapter The PC Port USB-to-HPNA adapter allows you to connect computers to your home network using existing phone lines. Following are the

More information

CLEARONE DOCUMENT 801-000-002 (REVISION 1.0) October, 2008. with Converge Pro Units

CLEARONE DOCUMENT 801-000-002 (REVISION 1.0) October, 2008. with Converge Pro Units APPLICATION NOTES Converge Pro Products CLEARONE DOCUMENT 801-000-002 (REVISION 1.0) October, 2008. Troubleshooting USB Connections with Converge Pro Units Description This document explains how to connect

More information

Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)

Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode) En Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode) Windows XP This document provides basic instructions on configuring the WT-4 wireless transmitter and a Windows XP Professional SP2 computer

More information

Shearwater Research Dive Computer Software Manual

Shearwater Research Dive Computer Software Manual Shearwater Research Dive Computer Software Manual Revision 1.3 Table of Contents 1. Basic overview of components 2. O/S IrDA driver installation 2.1 USB IrDA installation for Windows XP Home/Pro editions

More information

3. USB DRIVER. 3-1. Installation of USB driver. 3-1-1. Driver for Infinity SD Data Logger. INFINITY Series Acquisition Tools Manual

3. USB DRIVER. 3-1. Installation of USB driver. 3-1-1. Driver for Infinity SD Data Logger. INFINITY Series Acquisition Tools Manual 3. USB DRIVER 3-1. Installation of USB driver Before you launch this software, the driver should be once surely registered. Access between the instrument and a PC through the USB cable supplied by us as

More information

SATO Network Interface Card Configuration Instructions

SATO Network Interface Card Configuration Instructions SATO Network Interface Card Configuration Instructions Table of Contents Section Page 1. Reset of wired/wireless interface card 3 2. Installing the All-In-One Utility 4 3. Configuring wired/wireless Ethernet

More information

Do not start HiQnet London Architect on the computer until instructed to do so below at Start and Configure HiQnet London Architect.

Do not start HiQnet London Architect on the computer until instructed to do so below at Start and Configure HiQnet London Architect. This guide will walk you through the process of configuring your PC running HiQnet London Architect to communicate with a network of Soundweb London devices. Before you begin, please ensure that all Soundweb

More information

1. Introduction. 1.1 Minimum Requirements. 1.2 Package Content. 1.3 Features

1. Introduction. 1.1 Minimum Requirements. 1.2 Package Content. 1.3 Features 1. Introduction 1.1 Minimum Requirements Microsoft Windows 2000 / XP / Vista 32bit. Pentium-class processor (200MHz CPU or above) 32MB RAM or above Minimum 10 MB Hard Disk Drive Space Free USB port 1.2

More information

EDGE FX Network configuration

EDGE FX Network configuration Page 1 of 16 TITLE: Category: EDGE FX Network configuration GERBER EDGE Document Number: 4280 Supplied by: Gerber Service Last Modified: April 14, 2011 Summary: In order to connect an EDGE FX to your PC

More information

CCASS (& CCMS) Terminal Installation Procedures. Version: 4.0

CCASS (& CCMS) Terminal Installation Procedures. Version: 4.0 CCASS (& CCMS) Terminal Installation Procedures Version: 4.0 Date: May 2016 Procedures: The purpose of this section is to describe the installation procedures for the CCASS (& CCMS) Terminal ( C3T ). The

More information

UX3600/NT/NTL/NTS Quick Start Guide This Quick Start Guide will explain how to connect and communicate with the EAW UX3600, NTL720, NTS250, KFNT, and JFNT powered speakers. Table of Contents 1. Downloading

More information