L Firmware And FPGA Configuration Upgrade

Size: px
Start display at page:

Download "L1255-4149 Firmware And FPGA Configuration Upgrade"

Transcription

1 Technical Note TN133 Issue:2 L Firmware And FPGA Configuration Upgrade IMPORTANT NOTE: When using USB to Serial converters and upgrading the Firmware there is a danger of early L1255s becoming unresponsive. It is not advised to upgrade L1255s in this way when upgrading in preparation for a forthcoming broadcast. Please follow the instructions carefully and contact link if you are unsure of how to carry out the upgrade.

2 Checking Firmware Version There are two ways of checking the firmware version on the L If the L is connected to a receiver it is possible to view the version by looking under status in the CCU menu on the receiver front panel. Alternatively it is possible to view the firmware by connecting into the L using a serial terminal program such as Hyperterminal or TeraTerm. Connect a 9-way null modem cable between the OCP connector on the L and a COM port of a PC. Set you serial terminal program to connect the COM port at 9600Baud, 8 data bits, no parity, 1 stop bit. On power-up of the L type the characters L,R,L,[esc] (lowercase) into the terminal program to enter the serial interface. Note: When using a USB to serial converter it is necessary not to have no flow control when first connecting to the L1255. Rear Panel of the L On typing LRL[esc] (lowercase) you will be presented with the following in the terminal window:- Output of terminal on entering the serial interface In this case the firmware is at version 14 and the FPGA configuration present in Bank 3.

3 Upgrading Firmware In order to upgrade the firmware firstly connect into the serial terminal (see checking firmware version section). On connection press h to bring up the list of commands. List of commands Press s to download the firmware and then y to confirm. The following will be displayed:- Set the COM port parameters as stated in the terminal window. For TeraTerm go to Setup> Serial Port. Note: When using a USB to serial converter adjust the line delay to 100ms/line. This will be advised on the terminal interface for L1255s purchased after the 1 st May 2010.

4 Go to file and send selecting the upgrade file kernel_x.xx_serd.hex When the file is sending the serial terminal will display the progress.

5 Once the firmware has loaded it will give an instruction to power down. Cycle the power and as before type in the keys L,R,L, [esc] to connect to the serial console. The firmware version number matches that of the upgrade file. Upgrading the FPGA Configuration The FPGA upgrade is a similar procedure to the firmware upgrade. Once again press h to view all options then press 'e' to erase all the fpga proms. Press 'y' to confirm. Now press 'h' again followed by 'd' to download FPGA code. Press 'y' to confirm. With XON/OFF flow control still set and a delay of 100ms/line send the file al _vx_xr.mot. All FPGA upgrade files are named al _vx_xr.mot. Note: When using a USB to serial converter adjust the line delay to 100ms/line. This will be advised on the terminal interface for L1255s purchased after the 1 st May On completion the serial terminal will display the following:-

6 Power cycle the L It is now completely upgraded and ready for use.

7 Upgrading the Sony Processor Configuration The Sony processor firmware can be upgraded in a similar fashion to the other firmware but with some important differences. Connect to the L to bring up the following window. Press h to see a list of available commands. Note option a Download Sony Processor Firmware. Press a. The following results will be shown

8 Once this window has visible go to set up>serial port. Set the Transmit delay to 10msec/char and click ok. Now select file>send file

9 Make absolutely sure that the Binary option is selected. The file will have the name format CL132420vX_X_serial_dload.BIN Once the file has downloaded wait until the Programming complete message is received. This will take a few seconds. Now repower the L

DUKANE Intelligent Assembly Solutions

DUKANE Intelligent Assembly Solutions PC Configuration Requirements: Configuration Requirements for ipc Operation The hardware and operating system of the PC must comply with a list of minimum requirements for proper operation with the ipc

More information

Keep it Simple Timing

Keep it Simple Timing Keep it Simple Timing Support... 1 Introduction... 2 Turn On and Go... 3 Start Clock for Orienteering... 3 Pre Start Clock for Orienteering... 3 Real Time / Finish Clock... 3 Timer Clock... 4 Configuring

More information

Centurion C4 Transfer Guide using C4 File Transfer Utility

Centurion C4 Transfer Guide using C4 File Transfer Utility Centurion C4 Transfer Guide using C4 File Transfer Utility 1010536 02 23 11 Section 50 1.0 Background: 1.1 A valid configuration is required for the Centurion system. Configuration files are downloaded

More information

Using HyperTerminal with Agilent General Purpose Instruments

Using HyperTerminal with Agilent General Purpose Instruments Using HyperTerminal with Agilent General Purpose Instruments Windows HyperTerminal can be used to program most General Purpose Instruments (not the 531xx series counters) using the RS-232 Serial Bus. Instrument

More information

To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:

To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification: PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,

More information

Application Note: Connecting to a 2500 Series Processor using PLC Workshop

Application Note: Connecting to a 2500 Series Processor using PLC Workshop Application Note: Connecting to a 2500 Series Processor using PLC Workshop This application note will describe a step by step process for the three ways to connect to a 2500-CXXX with PLC Workshop. The

More information

Configuring Serial Terminal Emulation Programs

Configuring Serial Terminal Emulation Programs Configuring Serial Terminal Emulation Programs Table of Contents Configuring Serial Terminal Emulation Programs: An Introduction... 3 HyperTerminal... 3 Configuring HyperTerminal... 3 Tera Term Pro...

More information

56800/E SCI Hands-On Exercise

56800/E SCI Hands-On Exercise 56800/E SCI Hands-On Exercise 56800/E Slide 1 Training Presenter Logo Here Slide 1 Task Description Develop a monitor application that uses SCI in messages between PC and DSC56F801x EVB. HyperTerminal

More information

Accessing Diagnostics using a Dialup Modem

Accessing Diagnostics using a Dialup Modem Purpose This application note is meant to guide a user through the setup and use of a dial-up modem to retrieve diagnostics data from a remote master. Equipment Used This application note was written specifically

More information

NOTE: PLEASE DO NOT ATTEMPT TO INSTALL THE SOFTWARE BEFORE READING THIS DOCUMENT.

NOTE: PLEASE DO NOT ATTEMPT TO INSTALL THE SOFTWARE BEFORE READING THIS DOCUMENT. INLINE 5 Software INSTALL BULLETIN Page 2: Installing INLINE 5 Page 6: Removing INLINE 5 NOTE: PLEASE DO NOT ATTEMPT TO INSTALL THE SOFTWARE BEFORE READING THIS DOCUMENT. IMPROPER INSTALLATION OR USE CAN

More information

Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000

Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000 Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000 1.0 Introduction A Technical Application Note from Doppler System July 5, 1999 Version 3.x of the DDF6000, running version

More information

Driver Installation and Hyperterminal Operation of iload Digital USB Sensors

Driver Installation and Hyperterminal Operation of iload Digital USB Sensors Driver Installation and Hyperterminal Operation of iload Digital USB Sensors Driver Installation Insert the iload Digital USB Driver CD OR the LoadVUE or LoadVUE Lite CD into your computer s drive. If

More information

Knowledge Base POS/C31A Troubleshooting

Knowledge Base POS/C31A Troubleshooting [Concept] Serial Port Include RS-232, RS-422, RS-485 and USB Currently NUUO only supports RS-232 Also named as COM port by Microsoft Why Null Modem? The RS-232 standard is asymmetrical as to the definitions

More information

Centurion PLUS CPC4 Download Guide

Centurion PLUS CPC4 Download Guide Centurion PLUS CPC4 Download Guide using C4 File Transfer Utility. 1010537 03 01 10 Section 50 1.0 Background: 1.1 The Centurion PLUS Control system consists of a Centurion PLUS Core (CPC4 1) and Color

More information

Current Cost Data Cable User Guide. Installing and configuring the data cable

Current Cost Data Cable User Guide. Installing and configuring the data cable Current Cost Data Cable User Guide Installing and configuring the data cable Contents About the Data Cable... 3 Data Cable Installation Steps... 3 Post Installation Checks... 3 So the driver is installed,

More information

How to setup a serial Bluetooth adapter Master Guide

How to setup a serial Bluetooth adapter Master Guide How to setup a serial Bluetooth adapter Master Guide Nordfield.com Our serial Bluetooth adapters part UCBT232B and UCBT232EXA can be setup and paired using a Bluetooth management software called BlueSoleil

More information

Plena Voice Alarm System Firmware update

Plena Voice Alarm System Firmware update Plena Voice Alarm System Firmware update 1. Introduction It is advised to update a Bosch Plena Voice Alarm System with the latest released firmware. This Application Note describes how a firmware update

More information

T3 Mux M13 Multiplexer

T3 Mux M13 Multiplexer T3 Mux M13 Multiplexer User Manual [Type the abstract of the document here. The abstract is typically a short summary of the contents of the document. Type the abstract of the document here. The abstract

More information

Guide to Installing BBL Crystal MIND on Windows 7

Guide to Installing BBL Crystal MIND on Windows 7 Guide to Installing BBL Crystal MIND on Windows 7 Introduction The BBL Crystal MIND software can not be directly installed on the Microsoft Windows 7 platform, however it can be installed and run via XP

More information

Maintaining the Content Server

Maintaining the Content Server CHAPTER 7 This chapter includes the following Content Server maintenance procedures: Backing Up the Content Server, page 7-1 Restoring Files, page 7-3 Upgrading the Content Server, page 7-5 Shutting Down

More information

Bend Sensor USB User Guide

Bend Sensor USB User Guide Bend Sensor USB User Guide Copyright 2015Flexpoint Sensor Systems, Inc. Page 1 of 7 SEG040404B Contents Page Introduction... 3 Kit Contents... 3 Installation instructions... 4 FlexpointBSV software...

More information

Orangutan X2 Firmware Update Procedure

Orangutan X2 Firmware Update Procedure Introduction Orangutan X2 Firmware Update Procedure Most of the Orangutan X2 hardware is controlled by the mega168 microcontroller. Firmware updates with bug fixes or additional features can be installed

More information

IP SERIAL DEVICE SERVER

IP SERIAL DEVICE SERVER IP SERIAL DEVICE SERVER ( 1 / 2 / 4 serial port ) Installation guide And User manual Version 1.0 1Introduction... 5 1.1Direct IP mode...5 1.2Virtual COM mode...5 1.3Paired mode...6 1.4Heart beat... 6

More information

Application Note CTAN #374

Application Note CTAN #374 Application Note CTAN #374 The Application Note is specific to the CT software packages MentorSoft, UniSoft and SeSoft Windows 7 64-bit and the Older CT Software Scope Windows 7 64-bit Professional 64-bit

More information

Connecting and Setting Up Your Laptop Computer

Connecting and Setting Up Your Laptop Computer CHAPTER 3 Connecting and Setting Up Your Laptop Computer This chapter explains how to connect your laptop to the Cisco Unified MeetingPlace system and how to set up your laptop so that you can use HyperTerminal.

More information

SETTING UP A REMOTE MODEM CONNECTION Application Note 27

SETTING UP A REMOTE MODEM CONNECTION Application Note 27 SETTING UP A REMOTE MODEM CONNECTION Application Note 27 with WeatherLink for Windows Serial Version Only INTRODUCTION This document provides guidelines on how to set up a remote modem connection. This

More information

POS Integration. Prepared by: Binh Nguyen

POS Integration. Prepared by: Binh Nguyen POS Integration Prepared by: Binh Nguyen Point of Sale (POS) Compatibility To know whether it is possible to integrate your POS system with our DVR, please check whether the type of printer the POS system

More information

1 INTRODUCTION. This document describes the procedure to upgrade LTMR.

1 INTRODUCTION. This document describes the procedure to upgrade LTMR. 1 INTRODUCTION This document describes the procedure to upgrade LTMR. Limitation: this package and procedure describe only the upgrade of the LTMR firmware for all network versions (Modbus, Profibus, DeviceNet,

More information

Schneider OS-Loader usage via Ethernet or USB.

Schneider OS-Loader usage via Ethernet or USB. LHC Gas Systems 28 th February, 2007 Schneider OS-Loader usage via Ethernet or USB. Jacques ROCHEZ - IT/CO/FE Abstract This document is a guideline on how to configure correctly a PC for the use of the

More information

Firmware upgrade instructions for the Web/SNMP and Network

Firmware upgrade instructions for the Web/SNMP and Network Page 1 of 6 Answer ID 768 Firmware upgrade instructions for the Web/SNMP and Network Management Cards Question How do I upgrade the firmware on an APC Web/SNMP Management Card or Network Management Card?

More information

TP- 051 GPS RECEIVER

TP- 051 GPS RECEIVER TP- 051 GPS RECEIVER CONTENTS 1. Overview 3 2. Features 3 3. The advantages of TP-051 GPS Receiver 4 4. The appearance and structures 4 5. Applications 5 6. Installation steps for the TP-051 GPS Receiver

More information

ACU-1000 Manual Addendum Replacement of CPM-2 with CPM-4

ACU-1000 Manual Addendum Replacement of CPM-2 with CPM-4 ACU-1000 Manual Addendum Replacement of CPM-2 with CPM-4 1 PURPOSE:... 1 2 CPM-4/CPM-2 COMPATIBILITY... 2 2.1 NETWORK CABLES... 2 2.2 FACTORY DEFAULT SETTINGS... 2 2.3 CHANGING THE RS-232 SERIAL PORT BAUD

More information

SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS. Quick Start Instructions

SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS. Quick Start Instructions TM SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS Quick Start Instructions Introduction WinLoad for Windows was developed to simplify and speed up the task of programming Paradox control panels. Remote

More information

Updating MNS-BB CUSTOMER SUPPORT INFORMATION PK012906

Updating MNS-BB CUSTOMER SUPPORT INFORMATION PK012906 Updating MNS-BB PK012906 CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500

More information

Bluetooth HC-06 with serial port module Easy guide

Bluetooth HC-06 with serial port module Easy guide 1 Bluetooth HC-06 with serial port module Easy guide This manual consists of 3 parts: PART 1. Overview of Bluetooth HC-06 module with serial port. PART 2. Installing Bluetooth HC-06 module with Bolt 18F2550

More information

Technical Manual. For use with Caller ID signaling types: Belcore 202, British Telecom, & ETSI

Technical Manual. For use with Caller ID signaling types: Belcore 202, British Telecom, & ETSI Technical Manual For use with Caller ID signaling types: Belcore 202, British Telecom, & ETSI Caller ID.com WHOZZ CALLING? POS 2 Caller ID Monitoring Unit Technical Manual For use with Caller ID signaling

More information

FRM301 SNMP Upgrade Procedure

FRM301 SNMP Upgrade Procedure The information within this document is intended for experienced service personnel with knowledge of TCP/IP networking, PC networking configuration, serial terminal configuration and operation. Failure

More information

Cypress CY7C64225 USB-to-UART Setup Guide Version 1.3

Cypress CY7C64225 USB-to-UART Setup Guide Version 1.3 Cypress CY7C64225 USB-to-UART Setup Guide Version 1.3 Overview The Cypress CY7C64225 is a fully integrated USB-to-UART Bridge that provides a simple way of updating RS-232 based devices to USB with a minimal

More information

Quick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012

Quick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012 Quick Note 32 Using Digi RealPort with a Digi TransPort Router UK Support September 2012 1 Contents 1 Introduction... 3 1.1 Outline... 3 1.2 Assumptions... 3 1.3 Version... 3 2 Configuration & scenario...

More information

PM1122 INT DIGITAL INTERFACE REMOTE

PM1122 INT DIGITAL INTERFACE REMOTE PM1122 INT DIGITAL INTERFACE REMOTE PM1122 INT front panel description: 1. Clear wireless remotes knob: push this button for more than 2 seconds to clear the list of all assigned wireless remote settings

More information

GE Measurement & Control

GE Measurement & Control GE Measurement & Control TransPort PT878 USB Interface Guide 1.0 Introduction The TransPort PT878 portable ultrasonic flowmeter allows the user to update firmware, communicate with a PC running the GE

More information

User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M)

User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M) Document code: MN67038-2_ENG Revision 1.400 Page 1 of 25 User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M) for

More information

SNMP-1 Configuration Guide

SNMP-1 Configuration Guide SNMP-1 Configuration Guide You must configure the Net Logic Card before it can operate properly. You have two methods to configure the Net Logic Card: Using telnet or terminal. Using Telnet 1. Make sure

More information

This techno knowledge paper can help you if: You need to setup a WAN connection between a Patton Router and a NetGuardian.

This techno knowledge paper can help you if: You need to setup a WAN connection between a Patton Router and a NetGuardian. Problem: Patton / 240T WAN Setup Platform: NetGuardian 240T This TKP is a guide to setting up a PPP to T1 WAN connection between a Patton Model 2603 Router and a NetGuardian 240T. The example in this guide

More information

VRX Company Inc. Application Note: DacEasy Point of Sale setup for Pole Display

VRX Company Inc. Application Note: DacEasy Point of Sale setup for Pole Display VRX Company Inc. Application Note: DacEasy Point of Sale setup for Pole Display Version 1 NOTICES This document is copyright by VRX Company Inc. Copyright law prohibits reproduction of any part of this

More information

How To Connect A Directsofl To A Powerpoint With An Acd With An Ctel With An Dm-Tel Modem On A Pc Or Ipad Or Ipa (Powerpoint) With A Powerline 2 (Powerline

How To Connect A Directsofl To A Powerpoint With An Acd With An Ctel With An Dm-Tel Modem On A Pc Or Ipad Or Ipa (Powerpoint) With A Powerline 2 (Powerline Application Note Last reviewed: 03/17/2008 AN-KEP-003.doc Page 1 of 23 Introduction... 1 Recommended s and ports to use... 1 Cable Wiring... 2 MDM-TEL Configuration ( Wizard)... 3 Direct Logic Communications

More information

Liebert IntelliSlot Web Cards

Liebert IntelliSlot Web Cards Monitoring For Business-Critical Continuity Liebert IntelliSlot Web Cards Firmware Upgrade Manual Liebert IntelliSlot Web Card, Liebert IntelliSlot Web Card-LB, Liebert IntelliSlot Web Card-LBDS, Liebert

More information

3.1 Connecting to a Router and Basic Configuration

3.1 Connecting to a Router and Basic Configuration 3.1 Connecting to a Router and Basic Configuration Objective This lab will focus on the ability to connect a PC to a router in order to establish a console session and observe the user interface. A console

More information

OPERATOR INTERFACE PRODUCTS APPLICATION NOTE. Xycom 4800/2000 OIL (Operator Interface Language)- Series Terminals: Backup and Restore with ProComm

OPERATOR INTERFACE PRODUCTS APPLICATION NOTE. Xycom 4800/2000 OIL (Operator Interface Language)- Series Terminals: Backup and Restore with ProComm Page 1 of 9 Xycom 4800/2000 OIL (Operator Interface Language)- Series Terminals: Backup and Restore with ProComm Introduction The Xycom 4800/2000 OIL-series terminals offer you the ability to backup and

More information

User Manual. Thermo Scientific Orion

User Manual. Thermo Scientific Orion User Manual Thermo Scientific Orion Orion Star Com Software Program 68X637901 Revision A April 2013 Contents Chapter 1... 4 Introduction... 4 Star Com Functions... 5 Chapter 2... 6 Software Installation

More information

IP Interface for the Somfy Digital Network (SDN) & RS485 URTSII

IP Interface for the Somfy Digital Network (SDN) & RS485 URTSII IP Interface for the Somfy Digital Network (SDN) & RS485 URTSII Internet Protocol (IP) Interface Product Options Cat # 1810815 IP Interface Only Cat # 1810870: Interface and DB9/RJ45 Adapter (9015028)

More information

Debugging Network Communications. 1 Check the Network Cabling

Debugging Network Communications. 1 Check the Network Cabling Debugging Network Communications Situation: you have a computer and your NetBurner device on a network, but you cannot communicate between the two. This application note provides a set of debugging steps

More information

SMC7004ABR Barricade Broadband Router Installation Instructions

SMC7004ABR Barricade Broadband Router Installation Instructions SMC7004ABR Barricade Broadband Router Installation Instructions SPECIAL NOTE: Part D Upgrading the Firmware in Your Barricade MUST occur in ALL installations for multiple VPN sessions to work!!! SPECIAL

More information

Signature Center Getting Started Guide

Signature Center Getting Started Guide Signature Center Getting Started Guide 1113710 PRODUCED IN IRELAND Copyright 2010 McKesson Corporation and/or one of its subsidiaries. All Rights Reserved. This documentation is an unpublished work of

More information

BIODEX. ATOMLAB 500/WIPE TEST COUNTER DATA MANAGER SOFTWARE Version 1.10 (and higher). OPERATION MANUAL 086-333

BIODEX. ATOMLAB 500/WIPE TEST COUNTER DATA MANAGER SOFTWARE Version 1.10 (and higher). OPERATION MANUAL 086-333 ATOMLAB 500/WIPE TEST COUNTER DATA MANAGER SOFTWARE Version 1.10 (and higher). OPERATION MANUAL 086-333 BIODEX Biodex Medical Systems, Inc. 20 Ramsey Road, Shirley, New York, 11967-4704, Tel: 800-224-6339

More information

Instructions on How to Use HyperTerminal to Test Serial Ports ...

Instructions on How to Use HyperTerminal to Test Serial Ports ... Print Date: 04.03.2010 Testing Serial Cards Instructions on How to Use HyperTerminal to Test Serial Ports... Brain Boxes Limited, Unit 3C, Wavertree Boulevard South, Wavertree Technology Park, Liverpool,

More information

Configuring the Switch with the CLI Setup Program

Configuring the Switch with the CLI Setup Program APPENDIXC Configuring the Switch with the CLI Setup Program This appendix provides a command-line interface (CLI) setup procedure for a standalone switch. To set up the switch by using Express Setup, see

More information

Aquadyne TechTip TITLE: TROUBLESHOOTING PC COM PORT AND MODEM PRODUCTS AFFECTED SYMPTOMS POSSIBLE CAUSES

Aquadyne TechTip TITLE: TROUBLESHOOTING PC COM PORT AND MODEM PRODUCTS AFFECTED SYMPTOMS POSSIBLE CAUSES Aquadyne TechTip TITLE: TROUBLESHOOTING PC COM PORT AND MODEM COMMUNICATIONS WITH AN OCTOPUS. Article # 072297-1 Last reviewed: 03/25/98 Keywords: Serial Port, Modem, Polling, AquaWeb, Node Not Responding

More information

Installing PowerLink on Windows 7 64-bit

Installing PowerLink on Windows 7 64-bit Instruction Manual Version 1.0, Code No. 20 751 806 1 Introduction... 3 2 Installing Virtual PC... 3 3 Configuring Windows XP Mode... 5 4 Installing Powerlink to Virtual XP... 8 5 Run PowerLink software

More information

Connecting your Omega/BetaPAT PLUS to a PC via a USB

Connecting your Omega/BetaPAT PLUS to a PC via a USB Connecting your Omega/BetaPAT PLUS to a PC via a USB Install software Windows XP and below Insert the disc into your computers disc drive and run through the setup wizard. Windows Vista & 7 1. Insert the

More information

Connecting the DG-102S VoIP Gateway to your network

Connecting the DG-102S VoIP Gateway to your network Contents of Package: DG-102S VoIP Station Gateway Power adapter CD-ROM, including User s Manual Quick Install Guide Requirements: RS-232 Console Cable Two RJ-45 CAT-5 Straight-Through Cables For more information

More information

Update Firmware from GUI

Update Firmware from GUI Update Firmware from GUI Purpose: Update firmware from embedded GUI. Product Affect: SA-4551S, SA-6651S, SA-6651E, SA-8850S, SS-4551E, SS-4552E, SS-6651E, SS-6652E, SS-4501E, SS-4501R, SS-4502E, SS-4502R,

More information

SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual

SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual Version 1.0 - January 20, 2015 CHANGE HISTORY Version Date Description of Changes 1.0 January 20, 2015 Initial Publication

More information

SVA025 Netcom2 FAQ Rev 1. Mitsubishi Netcom 2 FAQ

SVA025 Netcom2 FAQ Rev 1. Mitsubishi Netcom 2 FAQ SVA025 Netcom2 FAQ Rev 1 Mitsubishi Netcom 2 FAQ SVA025 Netcom2 FAQ Rev 1 2 What series of Netcom did we purchase? Netcom 2 FAQ Mitsubishi has several different versions of communications available. 1.

More information

Changing Password for Ingate Firewalls/SIParators Rickard Nilsson

Changing Password for Ingate Firewalls/SIParators Rickard Nilsson Changing Password for Ingate Firewalls/SIParators Rickard Nilsson Ingate Firewall/SIParator version: Valid from 5.0.1, released in 5.0.4 Document version: 1.0 Table of Contents Changing Password for Ingate

More information

Download ME6008M1 Event Log

Download ME6008M1 Event Log Download ME6008M1 Event Log ManuFlo Flow Measurement Products A Division of Manu Electronics Pty Ltd 41 Carter Road, Brookvale NSW 2100 Australia Phone: +61 2 9938-1425 or +61 2 9905-4324 Fax: +61 2 9938-5852

More information

Remote Monitoring and Control of the R&S FSL with a Web Browser

Remote Monitoring and Control of the R&S FSL with a Web Browser Rohde & Schwarz Products: R&S FSL3, R&S FSL6, R&S FSL18 Remote Monitoring and Control of the R&S FSL with a Web Browser Application Note This application notes describes remote operation or monitoring

More information

Application Bulletin

Application Bulletin INTELLIGENT CONTROLS INC PO BOX 638 34 SPRING HILL RD SACO, ME 04072 U S A Application Bulletin 000-2045 REV. B Retrieving Tap Change Indication Data from an INCON1250B via an SEL 2020 or 2030 Communications

More information

APR-PRT3 Printer Module: C-Bus Programming Instructions

APR-PRT3 Printer Module: C-Bus Programming Instructions APR-PRT3 Printer Module: C-Bus Programming Instructions We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us

More information

ETHERNET WEATHER STATION CONNECTIONS Application Note 33

ETHERNET WEATHER STATION CONNECTIONS Application Note 33 ETHERNET WEATHER STATION CONNECTIONS Application Note 33 With WeatherLink and a Device Server INTRODUCTION It is possible to substitute an Ethernet connection for the direct USB or serial connection that

More information

Installing the drivers for the Current Cost Data Cable

Installing the drivers for the Current Cost Data Cable Installing the drivers for the Current Cost Data Cable Contents Introduction... 3 About Current Cost Monitors... 3 About the XML... 3 The Historical XML Feed... 3 Forcing the History to Download... 3 About

More information

ScanWin Installation and Windows 7-64 bit operating system

ScanWin Installation and Windows 7-64 bit operating system ScanWin Installation and Windows 7-64 bit operating system In order to run the ScanWin Pro install and program on Windows 7 64 bit operating system you need to install a Virtual PC and then install a valid,

More information

FN:PCMCSET-M1.DOC. PCMCSET SOFTWARE for ATS Master Clocks System Clocks and Displays

FN:PCMCSET-M1.DOC. PCMCSET SOFTWARE for ATS Master Clocks System Clocks and Displays FN:PCMCSET-M1.DOC PCMCSET SOFTWARE for ATS Master Clocks System Clocks and Displays ATS FREE SOFTWARE AGREEMENT Applied Technical Systems (ATS) grants you the right to use this software according to the

More information

I. DigitalCAT Captioning Software Overview... 1. A. Welcome... 1. B. Acquiring the Captioning Add-On... 1. C. Purpose of this Guide...

I. DigitalCAT Captioning Software Overview... 1. A. Welcome... 1. B. Acquiring the Captioning Add-On... 1. C. Purpose of this Guide... I. DigitalCAT Captioning Software Overview... 1 A. Welcome... 1 B. Acquiring the Captioning Add-On... 1 C. Purpose of this Guide... 1 II. Direct or Dial-Up Connections... 1 A. Direct Connections... 1 B.

More information

MAXREFDES46# Quick Start Guide UG6207; Rev 1; 9/15. Abstract

MAXREFDES46# Quick Start Guide UG6207; Rev 1; 9/15. Abstract MAXREFDES46# Quick Start Guide UG6207; Rev 1; 9/15 Abstract The MAXREFDES46# 4-Channel Analog Input Output Quick Start Guide describes the steps required to quickly get the MAXREFDES46# reference design

More information

SheevaPlug Development Kit README Rev. 1.2

SheevaPlug Development Kit README Rev. 1.2 SheevaPlug Development Kit README Rev. 1.2 Introduction... 3 Flow to use the Software Development Kit packages... 3 Appendix A... 5 GCC cross-compiler... 5 Appendix B... 6 Mini-USB debug driver installation

More information

Remote Access Server - Dial-Out User s Guide

Remote Access Server - Dial-Out User s Guide Remote Access Server - Dial-Out User s Guide 95-2345-05 Copyrights IBM is the registered trademark of International Business Machines Corporation. Microsoft, MS-DOS and Windows are registered trademarks

More information

PRN_LOAD 17.04.2002 16:22

PRN_LOAD 17.04.2002 16:22 PRN_LOAD.EXE is a user-friendly program for loading the HPR4915 with new firmware or fonts. It is based on the DOS operating system and also runs under WIN 95/89/NT WIN2000 WIN ME WIN XP and OS/2. However,

More information

October 2011 3726 07897 601 Rev. B Page 1

October 2011 3726 07897 601 Rev. B Page 1 Upgrading Polycom SoundStation2W software to Version 1.607 and CVM to Version 1.85 Installer for Microsoft Windows Vista and Windows 7 (32 and 64 bit) Operating Systems NOTE: Two versions of upgrader are

More information

1. Make sure that no client accounts are open. 2. Click on Setup, then click Modem. The Modem Setup window will appear.

1. Make sure that no client accounts are open. 2. Click on Setup, then click Modem. The Modem Setup window will appear. SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS WINLOAD MODEM SETUP The modem setup is a very important step in the connection process. If the modem setup is not properly completed communication between

More information

1. Do I need to upgrade my Broadband at Home modem firmware?

1. Do I need to upgrade my Broadband at Home modem firmware? 1. Do I need to upgrade my Broadband at Home modem firmware? Please follow the steps below to ensure you have the most up to date firmware for your Broadband at Home modem. 1. Make sure that you have connected

More information

GST-1 Troubleshooting FAQ

GST-1 Troubleshooting FAQ GST-1 Troubleshooting FAQ General: This FAQ addresses several common problems encountered and address the Windows 2000 associated interface problem. GST-1 s currently being shipped have been re-programmed

More information

Connecting the Console Port to a PC

Connecting the Console Port to a PC This document covers tasks associated with connecting a console port to a PC, and includes the following topics: Console (rollover) Cable and Adapters Making the physical connection Connecting using HyperTerminal

More information

3.1 Backup and Recovery System

3.1 Backup and Recovery System 3.1 Backup and Recovery System FriendlyARM English User Manual 197 In the development process, we often need to constantly update the programmer and system debugging, and sometimes you will be with the

More information

Using the M90-GSM s SMS feature

Using the M90-GSM s SMS feature Using the M90-GSM s SMS feature SMS messaging...1 About SMS messaging...1 Overview of M90 SMS messaging...3 SMS phone book...3 Creating SMS messages...4 Creating SMS text messages...4 Attaching variables...4

More information

AUDITVIEW USER INSTRUCTIONS

AUDITVIEW USER INSTRUCTIONS COMBOGARDPRO AUDITVIEW USER INSTRUCTIONS The ComboGard Pro AuditView software allows the Manager to view, save, and print the audit records. The ComboGard Pro lock maintains the last 63 lock events in

More information

MS830 / MS833 Barcode Reader v1.0 9-December-2014

MS830 / MS833 Barcode Reader v1.0 9-December-2014 MS830 / MS833 Barcode Reader v1.0 9-December-2014 Publication Information 2014 Imagine Communications Corp. Proprietary and Confidential. Imagine Communications considers this document and its contents

More information

Software Repair Assistant Manual for DuraXV

Software Repair Assistant Manual for DuraXV Software Repair Assistant Manual for DuraXV 2015 Kyocera Corporation. All rights reserved. KYOCERA is a registered trademark of Kyocera Corporation. All other trademarks are the property of their respective

More information

3.1 RS-232/422/485 Pinout:PORT1-4(RJ-45) RJ-45 RS-232 RS-422 RS-485 PIN1 TXD PIN2 RXD PIN3 GND PIN4 PIN5 T+ 485+ PIN6 T- 485- PIN7 R+ PIN8 R-

3.1 RS-232/422/485 Pinout:PORT1-4(RJ-45) RJ-45 RS-232 RS-422 RS-485 PIN1 TXD PIN2 RXD PIN3 GND PIN4 PIN5 T+ 485+ PIN6 T- 485- PIN7 R+ PIN8 R- MODEL ATC-2004 TCP/IP TO RS-232/422/485 CONVERTER User s Manual 1.1 Introduction The ATC-2004 is a 4 Port RS232/RS485 to TCP/IP converter integrated with a robust system and network management features

More information

isppac-powr1220at8 I 2 C Hardware Verification Utility User s Guide

isppac-powr1220at8 I 2 C Hardware Verification Utility User s Guide November 2005 Introduction Application Note AN6067 The isppac -POWR1220AT8 device from Lattice is a full-featured second-generation Power Manager chip. As part of its feature set, this device supports

More information

Prestige 324. Prestige 324. Intelligent Broadband Sharing Gateway. Version 3.60 January 2003 Quick Start Guide

Prestige 324. Prestige 324. Intelligent Broadband Sharing Gateway. Version 3.60 January 2003 Quick Start Guide Prestige 324 Intelligent Broadband Sharing Gateway Version 3.60 January 2003 Quick Start Guide 1 Introducing the Prestige The Prestige is a broadband sharing gateway with a built-in four-port 10/100 Mbps

More information

Prestige 324 Quick Start Guide. Prestige 324. Intelligent Broadband Sharing Gateway. Version V3.61(JF.0) May 2004 Quick Start Guide

Prestige 324 Quick Start Guide. Prestige 324. Intelligent Broadband Sharing Gateway. Version V3.61(JF.0) May 2004 Quick Start Guide Prestige 324 Intelligent Broadband Sharing Gateway Version V3.61(JF.0) May 2004 Quick Start Guide 1 1 Introducing the Prestige The Prestige is a broadband sharing gateway with a built-in four-port 10/100

More information

Programming Flash Microcontrollers through the Controller Area Network (CAN) Interface

Programming Flash Microcontrollers through the Controller Area Network (CAN) Interface Programming Flash Microcontrollers through the Controller Area Network (CAN) Interface Application te Programming Flash Microcontrollers through the Controller Area Network (CAN) Interface Abstract This

More information

USB DRIVER INSTALLATION GUIDE

USB DRIVER INSTALLATION GUIDE USB DRIVER INSTALLATION GUIDE Please read this installation guide before installing the USB driver. This installation guide describes how to install the USB driver included in the Icom product s CD. If

More information

Using and Installing: HCS12C32 Board, HCS12C128 Board, USB-to-Serial port driver, and HyperTerminal

Using and Installing: HCS12C32 Board, HCS12C128 Board, USB-to-Serial port driver, and HyperTerminal Using and Installing: HCS12C32 Board, HCS12C128 Board, USB-to-Serial port driver, and HyperTerminal CMPEN 472, Spring 2013, Kyusun Choi Download from the PSU Angel cmpen472 page, the USB-to-Serial port

More information

50-Port 10/100/1000Mbps with 4 Shared SFP. Managed Gigabit Switch WGSW-50040. Quick Installation Guide

50-Port 10/100/1000Mbps with 4 Shared SFP. Managed Gigabit Switch WGSW-50040. Quick Installation Guide 50-Port 10/100/1000Mbps with 4 Shared SFP Managed Gigabit Switch WGSW-50040 Quick Installation Guide Table of Contents 1. Package Content... 3 2. Switch Management... 4 3. Requirements... 5 4. Terminal

More information

EGCP-3 MC 8406-114 Revision H Software 5448-145 Revision F. Explanation of Software Changes Made for the EGCP-3 MC Control. Application Note 51298

EGCP-3 MC 8406-114 Revision H Software 5448-145 Revision F. Explanation of Software Changes Made for the EGCP-3 MC Control. Application Note 51298 EGCP-3 MC 8406-114 Revision H Software 5448-145 Revision F Explanation of Software Changes Made for the EGCP-3 MC Control Application Note 51298 WARNING DANGER OF DEATH OR PERSONAL INJURY WARNING FOLLOW

More information

SOFTWARE INSTALLATION INSTRUCTIONS

SOFTWARE INSTALLATION INSTRUCTIONS AUDITGARD LGA Electronic Combination Lock SOFTWARE INSTALLATION INSTRUCTIONS Implementation Package The AuditGard Software implementation package includes: 707013 AuditGard Software Install CD 42145 Programming/Audit

More information

RN-WIFLY-EVAL-UM. WiFly Evaluation Kit. 2012 Roving Networks. All rights reserved. RN-WIFLY-EVAL-UM Version 1.32r 10/9/2012 USER MANUAL

RN-WIFLY-EVAL-UM. WiFly Evaluation Kit. 2012 Roving Networks. All rights reserved. RN-WIFLY-EVAL-UM Version 1.32r 10/9/2012 USER MANUAL WiFly Evaluation Kit 2012 Roving Networks. All rights reserved. Version 1.32r 10/9/2012 USER MANUAL OVERVIEW This document describes the hardware and software setup for Roving Networks evaluation kits,

More information

Unpacking the Product. Rack Installation. Then, use the screws provided with the equipment rack to mount the firewall in the rack.

Unpacking the Product. Rack Installation. Then, use the screws provided with the equipment rack to mount the firewall in the rack. About This Guide This guide contains step-by-step instructions for setting up the D-Link DFL-260E/860E Firewall. Please note that the model you have purchased may appear slightly different from those shown

More information