41000 Series Control Valves

Transcription

1 Specification Data CH /98 Control Valves A Complete ine of Heavy Duty, Balanced, Cage Guided, Globe Valves with Noise Control o-db Trim

2 Table of Contents Foreword... 2 Numbering System... 3 Ratings/Connections... 3 General Data... 4 Allowable Pressure Drop Page Index... 4 Temperature Range/Seat eakage... 5 C V and F versus Travel Construction... 9 Materials Allowable Pressure Drops Dimensions Weights Accessories and Options Sales Offices and Distribution Centers... 3 Foreword Masoneilan s heavy-duty control valve line, engineered to handle the most demanding process conditions, exceeds the capabilities of regular valves. Broad Temperature Ranges for size, the provides effective control throughout a broad range of process temperatures from -19 C to +5 C. Higher Allowable Pressure Drops control valves provide exceptional and dependable performance over a wide range of pressure drops typical of severe services. Greater Capacity with ow Recovery Masoneilan s control valves have the highest capacities of contemporary cage-type globe valves. These unusually high capacities are attained with minimum pressure recovery, as indicated by high critical flow (F ) factors. High-Performance Materials are Standard Without exception, the materials we specify as standard on the have been tested and selected to provide trouble-free operation in services with high pressures and extreme temperatures. Therefore, specification is simplified and longevity on any application is assured. Variety of High Performance ngineered Trim Packages Available with full area as well as reduced C V capacities, trim options include : o-db Single Stage trim - provides excellent noise attenuation on gas and steam services and cavitation protection on liquid services. o-db Double Stage trim - designed for noise control on gas or steam at high pressure drop ratios. For more information regarding NAC conformance, cavitation, critical pressure drop, and VRT trim, consult your Masoneilan representative or refer to the following publications : 1. Masoneilan Handbook for Control Valve Sizing (Bulletin OZ00) 2. Masoneilan Noise Control Manual (Bulletin OZ3000) Trade names noted throughout are for reference only. Masoneilan reserves the right to supply trade named material or its equivalent. 2

3 Numbering System 1st 2nd 1st 2nd 3rd 4th 5th 4 1 Type Body Series Seal Type Control Characteristic Trim Type 37 Spring Diaphragm : direct, air to close (fail open action) 38 Spring Diaphragm : reverse, air to open (fail closed action) 87 Spring Diaphragm : direct, air to close (fail open action) 88 Spring Diaphragm : reverse, air to open (fail closed action) 41 Cage Guided Globe O. Undefined 3. Pressure nergized PTF Seal Ring 4. Auxiliary Shutoff Plug 5. Metal Seal Ring. PTF Seal Ring 9. Graphite Seal Ring 0. Undefined 1. inear 2. qual % 0. Undefined 1. Standard 2. o-db Single Stage 3. o-db Single Stage with Diffuser 4. o-db Double Stage Ratings/Connections Threaded Socket Weld Butt Weld RF & RTJ mm Valve inch to to to 400 to ANSI Class 150 to and equivalent PN ANSI Class 2500 and equivalent PN 80x50x80 0x50x0 0x80x0 3x2x3 4x2x4 4x3x4 to to 400x300x400 x12x Note : For AFNOR and DIN connections, consult Masoneilan 3

4 General Data Standard Valve (41300, 41400, 4, 400 and 41) Body type : high-capacity globe flow direction : see Allowable Pressure Drop Table o-db trim : flow to open for gas or steam o-db trim with diffuser : flow to close for gas or steam cavitation service : flow to close C V ratio : 0:1 standard capacity trim 50:1 o-db and reduced capacity trim Bonnet type : stud bolted, extended Trim cage : cylindrical ported or o-db plug : pressure balanced cage guided with metal, PTF, or graphite seal ring ; pressure balanced cage guided, with spring loaded internal auxiliary tight shutoff plug Flow Characteristic standard trim : linear, equal percentage o-db Double Stage Valve (41314) flow direction : flow to open gas or steam only C V ratio : 50:1 Trim cage : two-stage o-db plug : Flow Characteristic standard trim : type : handwheel : pressure balanced cage guided with pressure energized PTF seal ring linear spring diaphragm, optional Allowable Pressure Drop Page Index Model F.T.C./Page F.T.O./Page Model F.T.C./Page F.T.O./Page , 21, 22, , 21, 22, , 21, 22, , , 2, , 2, , , , , , 2, , 2, , , , 2, , 2, , , 27 4

5 Temperature Range/Seat eakage Seat eakage per Valve Temperature Range ( C) Model IC and Type mm inch Minimum Maximum ANSI / FCI 70.2 Class IV & V Standard IV Single Stage V (optional) o-db II Anti-Cavitation III IV III IV o-db Double Stage IV & V C v and F versus Travel Standard Trim (Single Stage) Models 41411, 41511, 411 and Flow Characteristic : INAR Percent of Travel F Valve ANSI Class Orifice Travel and Diameter mm inch equivalent PN (mm) (mm) Rated C V ,

6 Cv and F versus Travel Standard Trim (Single Stage) Models 41421, 41521, 421 and Flow Characteristic : QUA PRCNTAG Percent of Travel F Valve ANSI Class Orifice and Diameter Travel mm inch equivalent PN (mm) (mm) Rated C V , Series (Single Stage) Model Flow Characteristic : INAR Percent of Travel F Valve ANSI Class Orifice and Diameter Travel mm inch equivalent PN (mm) (mm) Rated C V ,

7 Cv and F versus Travel Series (Single Stage) Model Flow Characteristic : QUA PRCNTAG Percent of Travel F Valve ANSI Class Orifice and Diameter Travel mm inch equivalent PN (mm) (mm) Rated C V o-db /Anti-cavitation (Single Stage) Model Flow Characteristic : INAR Percent of Travel F Valve ANSI Class Orifice and Diameter Travel Rated C V mm inch equivalent PN (mm) (mm) ,

8 C v and F versus Travel o-db/anti-cavitation (Single Stage) Models ➀ Flow Characteristic : INAR Percent of Travel F Valve ANSI Class Orifice and Diameter Travel mm inch equivalent PN (mm) (mm) Rated C V , , , , , ➀ Where diffuser is added on high capacity trim, overall C V is reduced as much as 15% o-db (Double Stage) Model Flow Direction : FOW TO OPN Flow Characteristic : INAR Percent of Travel F Valve ANSI Class Nominal and Orifice Travel Diameter mm inch equivalent PN (mm) (mm) Rated C V ,

9 Body S/A Construction Balance Plug Construction 4, 400, 41 Series DN 50 to DN 400 (2" to ") (DN 50 to DN 0 Shown) Pilot Balanced Construction Series DN 50 to DN 0 (2" to 4") Pilot Balanced Construction Series DN 150 to DN 400 (" to ") 9

10 Materials Carbon and ow Alloy Steel Version Ref. No Temperature Range Description -29 C +343 C +427 C +454 C +5 C Standard Materials 1 Valve plug stem Martensitic St. St. Type 17-4 PH ASTM A 38 Gr 0 2 Packing flange stud Austenitic St. St. Type Packing flange nut Austenitic St. St. Type Packing flange Carbon steel zinc plated 5 Packing spacer Austenitic St. St. Type 303 Packing KVAR + PTF GRAPHIT 7 Bonnet CARBON ST ASTM A 2 Gr WCC Body CHROM-MOYBDNUM ST ASTM A 217 Gr WC 8 Valve body nut ASTM A 194 Gr 2H ASTM A 194 Gr 4 9 Plug pin Austenitic Stainless Steel Valve body gasket Spiral wound 3 St. St. with graphite filler 11 Seal ring type See page Plug spring (41400 only) INCON X Seat ring Austenitic St. St. Type 3 with hardfacing Seat ring gasket Valve plug Spiral wound 3 St. St. with graphite filler Martensitic St. St. Type 17-4 PH Cage Martensitic St. St. Type CANM Chromium-plated Flat spring ( " to ") Martensitic St. St. Type 17-4 PH Retaining ring (41400 only) INCON X750 (2 to 4") St. St. Type 3 w. hardfacing (" to ") St St type CA NM w. hardfacing Martensitic St. St. Type CANM Nitrited Martensitic St. St. Type CANM Nitrited INCON X750 + shot peening 20 Auxiliary plug (41400 only) (2" to 4") Martensitic St. St Type 4 ( to " ) Martensitic St. St. Type CANM with hardfaced and chromium-plated Martensitic St. St. Type CANM with hardfaced and chromium-plated 21 Valve body stud ASTM A 193 Gr B7 ASTM A 193 Gr 22 Guide bushing Martensitic St. St. Type 440 C Packing follower Austenitic St. St. Type 303

11 Materials Stainless Steel Version Temperature Range Ref. No Description -19 C -1 C -4 C -29 C +149 C +343 C +427 C +454 C +5 C Standard Materials Valve plug stem Packing flange stud Packing flange nut Packing flange Packing spacer Packing ASTM A 38 Gr 0 Martensitic St. St. Type 17-4 PH Austenitic St. St. Type 304 Austenitic St. St. Type 304 Stainless Steel Austenitic St. St. Type 303 KVAR + PTF ASTM A 38 Gr 0 GRAPHIT 7 Bonnet Body AUSTNITIC STAINSS ST TYP 3 8 Valve body nut ASTM A 194 Gr 8M ASTM A 194 Gr 4 ASTM A 194 Gr 2H ASTM A 194 Gr Plug pin Valve body gasket Seal ring type 3 Stainless Steel Spiral wound 3 St. St. with graphite filler See page Plug spring (41400 only) INCON X750 (2 to 4") St. St. Type 3 13 Seat ring Austenitic St. St. Type 3 with hardfacing with hardfacing (" to ") St. St. Type CANM with hardfacing Seat ring gasket Spiral wound 3 St. St. with graphite filler Valve plug Martensitic St. St. Type 17-4 PH Cage Martensitic St. St. Type CANM Chrome-plated Consult Masoneilan Consult Masoneilan Flat spring ( " to ") INCON X750 +shot peening Martensitic St. St. Type 17-4 PH INCON X750 + shot peening Retaining ring INCON X750 (41400 only) (2" to 4") Martensitic St. St. Type 4 Auxiliary plug Martensitic St. St. Type CANM Martensitic St. St. Type CANM (" to ") Martensitic St. St. Ty. CANM (41400 only) with hardfaced and chromium-plated with hardfaced and chrome-plated w. hardfaced & chromium-plated 21 Valve body stud ASTM A 193 Gr 8M ASTM A 320 Gr 7 ASTM A 193 Gr B7 ASTM A 193 Gr 22 Guide bushing Austenitic St. St. Ty. 3 w. hardfacing Martensitic St. St. Type 440 C Packing follower Austenitic St. St. Type

12 Seal Ring Construction Series has a Pressure nergized Polymeric Seal Ring and 4 Series has a Metal Seal Ring. eakage Class Ranging from Class II to Class V are obtainable with temperatures ranging from -19 C to +5 C. PUG CAG PUG CAG 400 Series has a TF Seal Ring and a Resilient Inner Ring. eakage Class IV is standard with temperatures ranging from -29 C to +149 C. 41 has a Graphite Seal Ring and Metal Inner Ring. eakage Class IV is standard with temperatures ranging from -19 C to +5 C for " to " and Class III for 2" to 4" PUG CAG PUG CAG DN 50 - DN 400 (2" - ") Materials of Construction Temperature Range -19 C -4 C -29 C +149 C +2 C +343 C +5 C Ref. No. Description Materials 31 Seal Ring PTF + 25% graphite and GIOY spring 35 xternal Seal Ring Ni-Resist ASTM A439 Type D3 3 Internal Seal Ring Ni-Resist ASTM A439 Type D3 Ni-Resist ASTM A439 Type D3 Nitrited 40 xternal Seal Ring PTF (Bronze) 41 Internal Seal Ring Nordel 45 xternal Seal Ring Graphite 4 Internal Seal Ring Ni-Resist Cast Iron ASTM A439 Type D3 Temperature Range -19 C -4 C -29 C +149 C +2 C +343 C +5 C 12

13 Optional Trim Types Single Stage Multi-hole ow Noise and Cavitation Protection DN 50 - DN 0 Shown (2" - 4") Multi-hole, ow Noise and Cavitation Protection Trim with Internal Diffuser DN DN 400 (" - ") Pressure nergized Seal DN DN 400 Shown (" - ") Double Stage High Attenuation, ow Noise Trim DN 50 - DN 0 Shown (2" - 4") 13

14 Allowable Pressure Drops for Series Flow To Close Models and eakage : IC and ANSI/FCI 70.2, Class IV (V Optional) Kevlar PTF Packing Valve - mm (inch) Rated C V bench net supply P bench net supply P AIR TO OPN AIR TO COS ANSI Class and equivalent PN Travel ine qual % ,, 2500 (mm) full reduced full reduced range range range range (2) (2) (2) (3) (3) (3) (4) (4) (4) () Nominal bench range of actuator used for specifying actuator on valve data sheet Actual bench range of valve/actuator assembly, resulting from combined pilot plug load force and actuator nominal bench range Model 87/88 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 14

15 Allowable Pressure Drops for Series Flow To Close Models and eakage : IC and ANSI/FCI 70.2, Class IV (V Optional) Kevlar PTF Packing Model 87/88 and 37/38 s Valve - mm (inch) Rated C V Travel AIR TO OPN AIR TO COS ANSI Class and equivalent PN inear qual % bench net supply P bench net supply P ,, 2500 (mm) full reduced full reduced range range range range () () () (8) (8) (8) (8) () () () (12) (12) (12) () () () Nominal bench range of actuator used for specifying actuator on valve data sheet Actual bench range of valve/actuator assembly, resulting from combined pilot plug load force and actuator nominal bench range Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 15

16 Allowable Pressure Drops for Series o-db/anti-cavitation Flow to Close Models and eakage : IC and ANSI/FCI 70.2, Class IV (V Optional) Kevlar PTF Packing Valve - mm (inch) Rated C V bench net supply P bench net supply P AIR TO OPN AIR TO COS ANSI Class and equivalent PN Travel High ,, 2500 (mm) Capacity Standard Reduced range range range range (2) (2) (2) (3) (3) (3) (4) (4) (4) () () () () (8) (8) (8) (8) () () () (12) (12) (12) () () Model 87/88 and 37/38 s Nominal bench range of actuator used for specifying actuator on valve data sheet Actual bench range of valve/actuator assembly, resulting from combined pilot plug load force and actuator nominal bench range Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information.

17 Allowable Pressure Drops for 4, 400 and 41 Series Flow To Close Models 41511, 41521, 411, 421, and eakage : IC and ANSI/FCI 70.2, Class II (2" - 4") 400 eakage : IC and ANSI/FCI 70.2, Class IV 41 eakage : IC and ANSI/FCI 70.2, Class III (2" - 4") Kevlar PTF Packing Model 87/88 Valve - mm (inch) Rated C V Travel ANSI Class and equivalent PN inear qual % ,, 2500 (mm) full reduced full reduced range range (2) (2) (2) (3) (3) (3) (4) (4) (4) () AIR TO OPN AIR TO COS bench supply P bench supply P Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 17

18 Allowable Pressure Drops for 4, 400 and 41 Series Flow To Close Models 41511, 41521, 411, 421, and eakage : IC and ANSI/FCI 70.2, Class III (" - ") 400 eakage : IC and ANSI/FCI 70.2, Class IV 41 eakage : IC and ANSI/FCI 70.2, Class IV (" - ") Kevlar PTF Packing Model 87/88 and 37/38 s Valve - mm (inch) Rated C V AIR TO OPN AIR TO COS bench supply P bench supply P ANSI Class and equivalent PN Travel inear qual % ,, 2500 (mm) full reduced full reduced range range () () () (8) (8) (8) (8) () () () (12) (12) (12) () () () Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information.

19 Allowable Pressure Drops for Single Stage Series Anti-cavitation Trim Flow To Close Models 41512, 41513, 412, 413, and eakage : IC and ANSI/FCI 70.2, Class II (2" - 4") 4 eakage : IC and ANSI/FCI 70.2, Class III (" - ") 400 eakage : IC and ANSI/FCI 70.2, Class IV 41 eakage : IC and ANSI/FCI 70.2, Class III (2" - 4") 41 eakage : IC and ANSI/FCI 70.2, Class IV (" - ") Kevlar PTF Packing Valve - mm (inch) Rated C V AIR TO OPN AIR TO COS ANSI Class and equivalent PN Travel High bench supply P bench supply P ,, 2500 (mm) Capacity Standard Reduced range range (2) (2) (2) (3) (3) (3) (4) (4) (4) () () () () (8) (8) (8) (8) () () () (12) (12) (12) () () Model 87/88 and 37/38 s Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 19

20 Allowable Pressure Drops for Series Flow To Open Models 41311, and eakage : IC and ANSI/FCI 70.2, Class IV Kevlar PTF Packing Model 87/88 Valve ANSI Class and Travel equivalent PN (mm) Rated (1) C V AIR TO OPN (2) Allowable pressure drops Bench range AIR TO COS Allowable pressure drops Bench range 3-15 Bench range - 30 Supply Supply mm inch , , 50 O ou 25 DB , 35 30, 25 ou 12 O DB , , 95 ou 45 O DB , , 145 ou 70 O DB , 2 ou 5 O DB (1) : inear : qual percentage (2) Supply pressure is 0.4 bar (5 psi) over bench range o-db Trim Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 20

21 Allowable Pressure Drops for Series Flow To Open Models 41311, and eakage : IC and ANSI/FCI 70.2, Class IV Kevlar PTF Packing Models and Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V (1) AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P (1) : inear ; : qual percentage Model Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 21

22 Allowable Pressure Drops for Flow To Open Models 41311, and eakage : IC and ANSI/FCI 70.2, Class V Kevlar PTF Packing Model 87/88 Valve ANSI Class and Travel equivalent PN (mm) Rated C V (1) AIR TO OPN (2) Allowable pressure drops Bench range AIR TO COS Allowable pressure drops Bench range 3-15 Bench range - 30 Supply Supply mm inch , , 50 O ou 25 DB , 35 30, 25 ou 12 O DB , , 95 ou 45 O DB , , 145 ou 70 O DB , 2 ou 5 O DB (1) : inear : qual percentage (2) Supply pressure is 0.4 bar (5 psi) over bench range o-db Trim Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 22

23 Allowable Pressure Drops for Series Flow To Open Models 41311, and eakage : IC and ANSI/FCI 70.2, Class V Kevlar PTF Packing Models and Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V (1) AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P (1) : inear : qual percentage Model Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information.

24 Allowable Pressure Drops for Series Flow To Open Model eakage : IC and ANSI/FCI 70.2, Class IV Kevlar PTF Packing Valve mm inch ANSI Class and Travel equivalent PN (mm) Rated C V AIR TO OPN (1) Allowable pressure drops Bench range Bench range 3-15 Supply Model 87/88 AIR TO COS Allowable pressure drops Bench range - 30 Supply (1) Supply pressure is 0.4 bar (5 psi) over bench range Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V Bench range AIR TO OPN Supply P Bench range AIR TO COS Supply P Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information.

25 Allowable Pressure Drops for Series Flow To Open Models eakage : IC and ANSI/FCI 70.2, Class V Kevlar PTF Packing Valve mm inch ANSI Class and Travel equivalent PN (mm) Rated C V AIR TO OPN (1) Allowable pressure drops Bench range Allowable pressure drops Bench range 3-15 Supply Model 87/88 AIR TO COS Bench range - 30 Supply (1) Supply pressure is 0.4 bar (5 psi) over bench range Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 25

26 Allowable Pressure Drops for 4, 400 and 41 Series Flow To Open Models 41511, 41521, 411, 421, and Models 41512, 41513, 412, 413, and eakage : IC and ANSI/FCI 70.2, Class II (2" - 4") 4 eakage : IC and ANSI/FCI 70.2, Class III (" - ") 400 eakage : IC and ANSI/FCI 70.2, Class IV 41 eakage : IC and ANSI/FCI 70.2, Class III (2" - 4") 41 eakage : IC and ANSI/FCI 70.2, Class IV (" - ") Kevlar PTF Packing Model 87/88 Valve mm inch ANSI Class and Travel equivalent PN (mm) Rated C V 75, , 50 ou 25 40, 35 30, 25 ou , , 95 ou 45 0, , 145 ou , 2 ou (1) O DB O DB O DB O DB O DB AIR TO OPN (2) Allowable pressure drops Bench range Allowable pressure drops Bench range 3-15 Supply AIR TO COS Bench range - 30 Supply (1) : inear ; : qual percentage (2) Supply pressure is 0.4 bar (5 psi) over bench range o-db Trim Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 2

27 Allowable Pressure Drops for 4, 400 and 41 Series Flow To Open Models 41511, 41521, 411, 421, and Models 41512, 41513, 412, 413, and eakage : IC and ANSI/FCI 70.2, Class III (" - 12") 400 eakage : IC and ANSI/FCI 70.2, Class IV 41 eakage : IC and ANSI/FCI 70.2, Class IV (" - 12") Kevlar PTF Packing Models 41511, 41521, 411, 421, and Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V (1) AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P (1) : inear : qual percentage Models 41512, 41513, 412, 413, and Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 27

28 Dimensions (mm) Flanged Butt, Socket Weld or Screwed nds Body S/A Pressure Class ANSI Class 150 ANSI Class 300 and equivalent PN and equivalent PN Valve BW BW BW RF RTJ & RF RTJ & RF RTJ & RF RTJ mm inch SW SW SW x50x80 3x2x3 (a) (a) (a) x50x0 4x2x4 - - (a) (a) (a) 0x80x0 4x3x x80x150 x3x 150x0x150 x4x x0x200 8x4x8 200x150x200 8xx x150x250 xx x200x300 12x8x (a) x300x400 x12x (a) (a) (a) (a) A ANSI Class and equivalent PN ANSI Class and equivalent PN (a) Consult Masoneilan 28

29 Dimensions (mm) Body S/A A B max C max Pressure Class ANSI Class ANSI Class 2500 and equivalent PN and equivalent PN All All Valve BW BW & RF RTJ & RF RTJ Classes Classes mm inch SW SW (a) (a) (a) 80x50x80 3x2x3 (a) (a) (a) (a) (a) (a) x50x0 4x2x4 (a) (a) (a) x80x0 4x3x (a) (a) x80x150 x3x x0x150 x4x (a) (a) (a) x0x200 8x4x x150x200 8xx x150x250 xx (a) x200x300 12x8x12 (a) (a) (a) 400 (a) x300x400 x12x (a) (a) (a) Note : For AFNOR and DIN dimensions, consult Masoneilan (a) Consult Masoneilan 29

30 Dimensions (mm) Shown with optional handwheel Model 87/88 Spring Diaphragm P R S T removal clearance = 150 mm 30

31 Dimensions (mm) Direct (37) Air to Close Reverse (38) Air to Open Direct (37) Air to Close Type 8A Handwheel Reverse (38) Air to Open Model 37/38 Spring Diaphragm Top-Mounted Handwheel Removal D F Type G H J Clearance Dir. Rev. Dir. Rev. with " Spring A with 20" Spring A A * 1 /2" NPT for No. 31

32 Weights (kg) Body S/A Weights Valve Flanged Connection Threaded / Welded Connection ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class 150, 300 and and and and 2500 and and and and 2500 and mm inch equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN Model 87/88 Spring Diaphragm Standard With Handwheel Model 37/38 Spring Diaphragm Standard With Handwheel Direct Reverse Direct Reverse () (20)

33 Accessories and Options Accessories Side Mounted Handwheels For 87/88 s (See Specification Data CR8788 ) Top Mounted Handwheels For 37/38 s (See Specification Data CR3000) 4700 P Series Pneumatic Positioner Instrument signals and bar 3-15 and -30 psig Split range 4700 Series lectropneumatic Positioner 8013 Series lectropneumatic Positioner Input range 4-20 ma Split range 77-4 or Airset (See Bulletin 78 ) 77- ockup Valve 2'' Gauge 0-2 bar 49 Rotary lectric Switches 49-1 (1-Switch SPDT) 49-2 (2-Switches SPDT) 49-3 Potentiometer Position Transmitter 49-4 (1-Proximity Detector) 49-5 (2-Proximity Detectors) 49- (1-Switch DPDT) 49-7 (2-Switches DPDT) 49-8 Opto-electronic Position Transmitter (See Specification Data CS7050 ) Other imit Switches 7000 lectropneumatic (I/P) Transducer Input range 4-20 ma Split range Output bar, adjustable bar, adjustable 3-15 psi, adjustable -30 psi, adjustable (See TS-Model 7000) Smart Valve Interface (SVI ) Smart Positioner and Smart Valve Process Controller Input range 4-20 ma Split range HART Communication (See Brochure BW00 ) ValVue Software Calibration, Configuration, Diagnostic, and Operator Interface Tool (See Brochure BW00 ) Solenoid Valves Options xtension Bonnets nvironmental Capabilities ( Packing) ubricator & Isolation Valve Other Flange Facings imit Stops Body Drain Plug Reducer and Nipple Connections NAC Compliance Custom Trim Materials U.O.P. Trim Materials Other Materials Soft Seat (IC and ANSI Class VI) Non-Destructive xamination Oxygen Cleaning lectric s For additional Accessories and Options, consult Masoneilan 2700 Controllers (See Bulletin 213 ) 33

34 Notes 34

35 Notes 35